Parameter List Edition 11/2004. sinamics SINAMICS G110

Transcription

1 Parameer Lis Ediion /2004 sinamics SINAMICS G0

2 SINAMICS G0 Documenaion Geing Sared Guide The Geing Sared Guide is designed o give he user quick access o all he basic informaion required o insall and se-up he SINAMICS G0 for operaion. Operaing Insrucions Gives informaion regarding he feaures of SINAMICS G0 including Insallaion, Commissioning, Conrol modes, Sysem Parameer srucure, Troubleshooing, Specificaions and available opions for he inverer. Parameer Lis The Parameer Lis conains a deailed descripion of all Parameers relaing o he SINAMICS G0 and is srucured in numerical order. Caalogues In he caalogue you will find all he necessary informaion o selec an appropriae inverer, as well as he Basic Operaor Panel and Communicaion Opions for he SINAMICS G0 series.

3 s SINAMICS SIMATIC MICROMASTER Produc Informaion Ediion 08/20 English Changes o he moor hermal proecion feaure of he MICROMASTER, SIMATIC & SINAMICS inverers On 9h November 200 Underwriers Laboraories Inc.(UL) revised he sandard for safey of power conversion equipmen which covers Siemens inverers. These changes in he sandard become effecive from he 9h of May 20. The changes relae o he performance of he sofware moor proecion offered by he inverer, in ha when he inverer is power-cycled i mus now reain he moor emperaure daa for use when power is reapplied. The following producs have had a sofware updae o comply wih he new requiremens. MICROMASTER 420 sofware V. or above. (Order No. 6SE ) MICROMASTER 40 sofware V2.2 or above. (Order No. 6SE640.) MICROMASTER 440 sofware V2.2 or above. (Order No. 6SE6440.) SINAMICS G0 sofware V.2 or above. (Order No. 6SL2..) SINAMICS G0D sofware V.6 or above. (Order No. 6SL5.. ) SINAMICS Pool CU-2 sofware V4.6 or above *) (CU20P-2, CU240E-2, CU240B-2, G20C, CU240D-2, CU250D-2). SIMATIC ET200pro FC-2 sofware V4.7 or above *) These producs now, by defaul, sore he moor emperaure (r004 for SINAMICS G0 and MICROMASTER 420; r005 for SINAMICS G0D and MICROMASTER 40/440) and re-use his value when power is reapplied: Parameer P060 has been changed o reflec his new requiremen as follows: The defaul value of parameer P060 is now 6 and he following seings have been added: Value 4 = Warning Only, no reacion, no rip, save emperaure on power down. Value 5 = Warning, Imax reducion, rip F00, save emperaure on power down. Value 6 = Warning, no reacion, rip F00, save emperaure on power down. *) Those unis have oher seings and defaul values. Please refer o he relevan parameer liss. The following producs will no have he sofware updae o suppor he new requiremens. All MICROMASTER varians All MICROMASTER 40 All MICROMASTER 4 All MICROMASTER 46 All MICROMASTER MMI / CM2 (Order No. 6SE2.. ) (Order No. 6SE640.. ) (Order No. 6SE64..) (Order No. 6SE646..) (Order No. 6SE96..) These producs are unchanged from heir original design, bu his is no longer complian wih he new requiremens. These producs may sill bear he UL symbol bu i is now he end users responsibiliy o provide lised moor overload proecion exernal o he inverer. We sugges he end user consider devices such as he Siemens overload relay RU series on he moor side of he inverer in order o provide he moor proecion, deails of which can be found a he link below: hp:// *A5E67445A*

4 Deusch Änderung zum hermischen Moorschuz bei Frequenzumrichern MICROMASTER, SIMATIC und SINAMICS Ab 9. November 200 ha Underwriers Laboraories Inc.(UL) den Sandard Safey of power conversion equipmen geänder. Davon sind auch Siemens-Frequenzumricher beroffen. Die Änderung ra am 9. Mai 20 in Kraf. Die Änderung bezieh sich auf die Leisungsfähigkei der Sofware für den Moorschuz, den der Frequenzumricher biee. Wenn bei dem Frequenzumricher ein Power-Cycle durchgeführ wird, muss der Wer der Mooremperaur beim Wiedereinschalen beibehalen werden. Folgende Produke erfüllen die neue Anforderung zum hermischen Moorschuz: MICROMASTER 420, ab Sofware V. (Besell- Nr. 6SE ) MICROMASTER 40, ab Sofware V2.2 (Besell- Nr. 6SE640.) MICROMASTER 440, Sofware V2.2. (Besell- Nr. 6SE6440.) SINAMICS G0, ab Sofware V.2 (Besell- Nr. 6SL2..) SINAMICS G0D, ab Sofware v.6 (Besell- Nr. 6SL5.. ) SINAMICS Pool CU-2, ab Sofware V4.6 *) (CU20P-2, CU240E-2, CU240B-2, G20C, CU240D-2, CU250D-2). SIMATIC ET200pro FC-2, ab Sofware V4.7 *) Dabei wird in der Werkseinsellung die Mooremperaur gespeicher (r004 für SINAMICS G0 und MICROMASTER 420; r005 für SINAMICS G0D und MICROMASTER 40/440) und beim Zuschalen der Spannung, also nach einem Power Cycle, für die Berechnung der Mooremperaur verwende. Die Änderung wird über folgende Erweierung des Parameers P060 realisier. Neue Einsellmöglichkeien: Wer 4 = nur Warnung, keine Reakion, Temperaurwer beim Ausschalen speichern. Wer 5 = Warnung, Imax reduzieren, Abschalung mi F00, Temperaurwer beim Ausschalen speichern. Wer 6 = Warnung, keine Reakion, Abschalung mi F00, Temperaurwer beim Ausschalen speichern (neue Werkseinsellung) *) Bei diesen Geräen gib es andere Einsellmöglichkeien und Werkseinsellungen. Beachen Sie die ensprechenden Lisenhandbücher! Die folgenden Produke erfüllen die neue Anforderung zum hermischen Moorschuz nich: Alle MICROMASTER Varianen (Besell- Nr. 6SE2.. ) Alle MICROMASTER 40 (Besell- Nr. 6SE640..) Alle MICROMASTER 4 (Besell- Nr. 6SE64..) Alle MICROMASTER 46 (Besell- Nr. 6SE646..) Alle MICROMASTER MMI / CM2 (Besell- Nr. 6SE96...) Am Original Design dieser Produke ha sich nichs geänder, aber sie erfüllen nich mehr die neuen UL Vorschrifen. Diese Produke dürfen am Typenschild ein UL Symbol zeigen, aber es is in der Veranworung des Endkunden einen geliseen exernen Moorüberlasschuz einzubauen. Wir empfehlen dem Endkunden ein Siemens-Überlasrelais der Serie RU moorseiig am Frequenzumricher zu insallieren, um den Moorschuz zu gewährleisen. Weiere Informaionen zu den Sirius RU-Überlasrelais finden Sie uner folgendem Link: hp:// *A5E67445A* 2 SINAMICS, SIMATIC and MICROMASTER inverers Produc Informaion, A5E67445A, Ediion 08/20

5 Français Changemen de la foncion de proecion hermique du moeur des variaeurs de viesse MICROMASTER & SINAMICS Le 09 Novembre 200 Underwriers Laboraories Inc.(UL) on révisé les sandards sur la sécurié des converisseurs de puissance ( safey of power conversion equipmen ) qui s appliquen aux variaeurs de viesse Siemens. Ces changemens des sandards son effecifs à parir du 09 Mai 20. Les changemens se rapporen à la performance de la foncion proecion hermique du moeur des variaeurs de viesse, en ceci que lorsque le variaeur de viesse es mis hors ension, les données hermiques du moeur doiven désormais êre conservées jusqu'à la prochaine mise sous ension e uilisaion du produi. Une mise à jour du sofware sur les produis suivans a éé implémenée afin de se conformer aux nouveaux sandards. MICROMASTER 420 sofware V. ou supérieur (Order No. 6SE ) MICROMASTER 40 sofware V2.2 ou supérieur (Order No. 6SE640.) MICROMASTER 440 sofware V2.2 ou supérieur (Order No. 6SE6440.) SINAMICS G0 sofware V.2 ou supérieur (Order No. 6SL2..) SINAMICS G0D sofware V. ou supérieur (Order No. 6SL5.. ) SINAMICS Pool CU-2 sofware V4.6 ou supérieur *) (CU20P-2, CU240E-2, CU240B-2, G20C, CU240D-2, CU250D-2). SIMATIC ET200pro FC-2 sofware V4.7 ou supérieur *) Désormais, les produis enregisren par défau la empéraure du moeur (r004 pour SINAMICS G0 e MICROMASTER 420 ; r005 pour SINAMICS G0D e MICROMASTER 40/440) e réuilisen cee valeur dès que la puissance es réablie sur l équipemen. Le paramère P060 a éé modifié afin de refléer ces changemens, comme indiqué ci-dessous : La valeur par défau du paramère P060 es désormais 6, e les réglages suivans on éé ajoués : Value 4 = Averissemen uniquemen, empéraure enregisrée lors de la mise hors ension. Value 5 = Averissemen e réducion Imax, arrê F00, empéraure enregisrée lors de la mise hors ension. Value 6 = Averissemen, pas réacion, arrê F00, empéraure enregisrée lors de la mise hors ension. *) Ces appareils on d aures possibiliés de réglage e d aures réglages usine. Tenir compe des ables de paramères! Les versions de sofware des produis suivans n inègren pas les modificaions pour répondre aux nouveaux sandards UL. ous les MICROMASTER varians ous les MICROMASTER 40 ous les MICROMASTER 4 ous les MICROMASTER 46 ous les MICROMASTER MMI / CM2 (N de réf. 6SE2..) (N de réf. 6SE640.. ) (N de réf. 6SE64..) (N de réf. 6SE646..) (N de réf. 6SE96..) Ces produis resen inchangés de leur concepion d origine e ne son pas conforme à ce nouveau sandards UL. Bien que ces produis aien oujours le marquage UL, les uilisaeurs finaux son mainenan responsables de la mise en place sur le variaeur d équipemen exerne de proecion hermique moeur lisés. Nous recommandons aux uilisaeurs exernes d uiliser des relais de proecion hermique côé moeur de ype Siemens Sirius RU. Plus d informaions sur ces relais son disponibles sous le lien suivan : hp:// SINAMICS, SIMATIC and MICROMASTER inverers Produc Informaion, A5E67445A, Ediion 08/20 *A5E67445A*

6 Ialiano Modifiche della funzione di proezione ermica del moore dei converiori di frequenza MICROMASTER, SIMATIC e SINAMICS In daa 9 novembre 200 Underwriers Laboraories Inc.(UL) ha riviso lo sandard per la "sicurezza delle apparecchiaure di conversione di poenza" (safey of power conversion equipmen) che si applica ai converiori di frequenza Siemens. Quese modifiche della norma sono enrae in vigore il 9 maggio 20. Le variazioni riguardano le caraerisiche della proezione sofware del moore offere dal converiore di frequenza: quando ques'ulimo viene speno e riacceso deve ora memorizzare i dai ermici del moore per riuilizzarli al momeno della riaccensione. I prodoi segueni hanno implemenao un aggiornameno del sofware per conformarsi ai nuovi requisii normaivi. MICROMASTER 420 sofware V. o successiva. (n. di ordinazione 6SE ) MICROMASTER 40 sofware V2.2 o successiva. (n. di ordinazione 6SE640.) MICROMASTER 440 sofware V2.2 o successiva. (n. di ordinazione 6SE6440.) SINAMICS G0 sofware V.2 o successiva. (n. di ordinazione 6SL2..) SINAMICS G0D sofware V.6 o successiva. (n. di ordinazione 6SL5.. ) SINAMICS Pool CU-2 sofware V4.6 o successiva *) (CU20P-2, CU240E-2, CU240B-2, G20C, CU240D-2, CU250D-2). SIMATIC ET200pro FC-2 sofware V4.7 o successiva *) Tali prodoi memorizzano adesso sisemaicamene la emperaura del moore (r004 per SINAMICS G0 e MICROMASTER 420; r005 per SINAMICS G0D e MICROMASTER 40/440) e riuilizzano queso valore alla riaccensione: Il paramero P060 è sao modificao come segue per enere cono di queso nuovo requisio: Il valore predefinio del paramero P060 è divenao 6 e sono sae aggiune le segueni imposazioni: Valore 4 = solo avviso, nessuna reazione, nessuna disinserzione, memorizzazione della emperaura allo spegnimeno. Valore 5 = solo avviso, riduzione Imax, disinserzione F00, memorizzazione della emperaura allo spegnimeno. Valore 6 = solo avviso, nessuna reazione, disinserzione F00, memorizzazione della emperaura allo spegnimeno. *) Quese unià presenano imposazioni e valori predefini differeni. Fare riferimeno alla lisa parameri corrispondene. I prodoi segueni non implemeneranno l'aggiornameno sofware e di conseguenza non supporeranno i nuovi requisii. Tue le variani MICROMASTER Tui i MICROMASTER 40 Tui i MICROMASTER 4 Tui i MICROMASTER 46 Tui i MICROMASTER MMI / CM2 (n. di ordinazione 6SE2.. ) (n. di ordinazione 6SE640.. ) (n. di ordinazione 6SE64..) (n. di ordinazione 6SE646..) (n. di ordinazione 6SE96..) Quesi prodoi resano invariai rispeo alla loro progeazione originale, ma non sono più compaibili con i nuovi requisii. Quesi prodoi possono manenere il simbolo UL, ma compee all'uene finale assicurare la proezione eserna conro i sovraccarichi del moore richiesa dalla norma per il converiore di frequenza. Per assicurare la proezione del moore si consiglia all'uene finale di ricorrere a disposiivi come i relè di sovraccarico Siemens della serie RU sul lao moore del converiore di frequenza. Per i deagli fare riferimeno al link seguene: hp:// *A5E67445A* 4 SINAMICS, SIMATIC and MICROMASTER inverers Produc Informaion, A5E67445A, Ediion 08/20

7 Español Cambios en la función de proección érmica del moor de los converidores MICROMASTER, SIMATIC y SINAMICS El 9 de noviembre de 200, Underwriers Laboraories Inc. (UL) revisó el esándar de "seguridad de los equipos converidores de energía", que afeca a los converidores de Siemens. Esos cambios en el esándar enraron en vigor el 9 de mayo de 20. Los cambios esán relacionados con el rendimieno de la proección del moor por sofware ofrecida por el converidor, por la cual, cuando el converidor se apaga y se vuelve a encender, debe conservar los daos sobre la emperaura del moor para uilizarlos al volver a arrancar. Para cumplir con los nuevos requisios, se ha acualizado el sofware de los producos siguienes. Sofware MICROMASTER 420 V. o superior. (Ref. 6SE ) Sofware MICROMASTER 40 V2.2 o superior. (Ref. 6SE640.) Sofware MICROMASTER 440 V2.2 o superior. (Ref. 6SE6440.) Sofware SINAMICS G0 V.2 o superior. (Ref. 6SL2..) Sofware SINAMICS G0D V.6 o superior. (Ref. 6SL5.. ) Sofware SINAMICS Pool CU-2 V4.6 o superior *) (CU20P-2, CU240E-2, CU240B-2, G20C, CU240D-2, CU250D-2). Sofware SIMATIC ET200pro FC-2 V4.7 o superior. *) De forma predeerminada, esos producos almacenan la emperaura del moor (r004 para SINAMICS G0 y MICROMASTER 420; r005 para SINAMICS G0D y MICROMASTER 40/440) y reuilizan ese valor al volver a arrancar: El parámero P060 se ha modificado para reflejar ese nuevo requisio de la forma siguiene: El valor predeerminado del parámero P060 ahora es 6, y se han añadido los siguienes ajuses: Valor 4 = Solo aviso, sin reacción, sin disparo, guardar emperaura al apagar. Valor 5 = Aviso, reducción Imáx, disparo F00, guardar emperaura al apagar. Valor 6 = Aviso, sin reacción, disparo F00, guardar emperaura al apagar. *) Esas unidades ienen oros ajuses y valores predeerminados. Consule las lisas de parámeros perinenes. Los producos siguienes no dispondrán de la acualización de sofware para cumplir los nuevos requisios. Todas las varianes de MICROMASTER Todos los MICROMASTER 40 Todos los MICROMASTER 4 Todos los MICROMASTER 46 Todos los MICROMASTER MMI/CM2 (Ref. 6SE2.. ) (Ref. 6SE640.. ) (Ref. 6SE64..) (Ref. 6SE646..) (Ref. 6SE96..) Esos producos no han sufrido cambios respeco a su diseño original, pero ya no cumplen los nuevos requisios. Esos producos odavía pueden llevar el símbolo UL, pero ahora es responsabilidad de los usuarios finales proporcionar una proección homologada conra sobrecarga del moor exerna al converidor. Para la proección del moor, recomendamos al usuario final disposiivos como el relé de sobrecarga de la serie RU de Siemens en el lado del moor del converidor. Puede enconrar información deallada en el enlace siguiene: hp:// *A5E67445A* SINAMICS, SIMATIC and MICROMASTER inverers 5 Produc Informaion, A5E67445A, Ediion 08/20

8 Parameers Fauls and Alarms 2 Appendix SINAMICS G0 20 W - kw Parameer Lis User Documenaion Inverer Type SINAMICS G0 Firmware Version.0 &. (on page 4) Issue /2004

9 Imporan Informaion /2004 Imporan Informaion This Parameer Lis mus only be used in conjuncion wih he Operaing Insrucions of he SINAMICS G0. WARNING Please pay special aenion o he Warnings, Cauions, Noices and Noes conained in he Operaing Insrucions. You will find he Operaing Insrucions on he Docu CD which can be ordered via your local Siemens deparmen under he Order No. 6SL27-0CA00-0AG0 or downloaded from our websie hp:// Summary of amendmens Ediion Valid for firmware version Saus/Changes Order no of he inverer 6SL2-0xxxx-xxxx 04/200.0 Firs issue Las digi 0 6SL2-0xxxx-xxx0 / Las digi 0 6SL2-0xxxx-xxx0. New feaures insered: P0727: 2-wire / -wire conrol mehod P24: DC braking sar frequency P26: Compound braking P4: Slip compensaion acivaion range P272: Threshold DC link volage P25-P27: Moor holding brake opimized Las digi 6SL2-0xxxx-xxx Approved Siemens Qualiy for Sofware and Training is o DIN ISO 900, Reg. No The reproducion, ransmission or use of his documen, or is conens is no permied unless auhorized in wriing. Offenders will be liable for damages. All righs including righs creaed by paen gran or regisraion of a uiliy model or design are reserved. Siemens AG All Righs Reserved. SINAMICS is a regisered rademark of Siemens Oher funcions no described in his documen may be available. However, his fac shall no consiue an obligaion o supply such funcions wih a new conrol, or when servicing. We have checked ha he conens of his documen correspond o he hardware and sofware described. There may be discrepancies neverheless, and no guaranee can be given ha hey are compleely idenical. The informaion conained in his documen is reviewed regularly and any necessary changes will be included in he nex ediion. We welcome suggesions for improvemen. Siemens handbooks are prined on chlorine-free paper ha has been produced from managed susainable foress. No solvens have been used in he prining or binding process. Documen subjec o change wihou prior noice. Prined in he Federal Republic of Germany Siemens-Akiengesellschaf. SINAMICS G0 Parameer Lis 4 6SL298-0BA-0BP0

10 /2004 Table of Conens Table of Conens Parameers Inroducion o SINAMICS G0 Sysem Parameers Quick commissioning (P000=) Parameer Descripion Fauls and Alarms Faul messages Alarm Messages Appendix Lis of Abbreviaions Parameer Lis SINAMICS G0 6SL298-0BA-0BP0 5

11 Parameers /2004 Parameer Lis SINAMICS G0 6 6SL298-0BA-0BP0

12 /2004 Parameers Parameers. Inroducion o SINAMICS G0 Sysem Parameers The layou of he parameer descripion is as follows. Par number 2 Parameer name 9 Min: [index] CSa: 5 Daaype: 7 Uni: 0 Def: 4 P-Group: 6 Acive: 8 QuickComm.: Max: 2 : 2 Descripion:. Parameer number Indicaes he relevan parameer number. The numbers used are 4-digi numbers in he range 0000 o Numbers prefixed wih an r indicae ha he parameer is a read-only parameer, which displays a paricular value bu canno be changed direcly by specifying a differen value via his parameer number (in such cases, dashes - are enered a he poins Uni, Min, Def and Max in he header of he parameer descripion. All oher parameers are prefixed wih a P. The values of hese parameers can be changed direcly in he range indicaed by he Min and Max seings in he header. [index] indicaes ha he parameer is an indexed parameer and specifies he number of indices available. 2. Parameer name Indicaes he name of he relevan parameer. The BICO sysem is no available wih he SINAMICS G0 inverer. To allow he parameer names o be used across a variey of inverer ypes, he names of parameer have no been changed.. Csa Commissioning saus of he parameer. Three saes are possible: Commissioning C Run U Ready o run T This indicaes when he parameer can be changed. One, wo or all hree saes may be specified. If all hree saes are specified, his means ha i is possible o change his parameer seing in all hree inverer saes. 4. P-Group Indicaes he funcional group of he paricular. Noe Parameer P0004 (parameer filer) acs as a filer and focuses access o parameers according o he funcional group seleced. Parameer Lis SINAMICS G0 6SL298-0BA-0BP0 7

13 Parameers / Daaype The daa ypes available are shown in he able below. Noaion Meaning U6 U2 I6 I2 Floa 6. Acive Indicaes wheher 6-bi unsigned 2-bi unsigned 6-bi ineger 2-bi ineger Floaing poin Immediaely changes o he parameer values ake effecive immediaely afer hey have been enered, or firs confirm he P buon on he basic operaor panel (BOP) mus be pressed before he changes ake effec. 7. Uni Indicaes he uni of measure applicable o he parameer values 8. QuickComm Indicaes wheher or no (Yes or No) a parameer can only be changed during quick commissioning, i.e. when P000 (parameer groups for commissioning) is se o (quick commissioning). 9. Min Indicaes he minimum value o which he parameer can be se. 0. Def Indicaes he defaul value, i.e. he value which applies if he user does no specify a paricular value for he parameer.. Max Indicaes he maximum value o which he parameer can be se. 2. Indicaes he level of user access. There are hree access levels: Sandard, Exended and Exper. The number of parameers ha appear in each funcional group depends on he access level se in P000 (user access level). Parameer Lis SINAMICS G0 8 6SL298-0BA-0BP0

14 /2004 Parameers. Descripion The parameer descripion consiss of he secions and conens lised below. Some of hese secions and conens are opional and will be omied on a caseo-case basis if no applicable. Descripion: Brief explanaion of he parameer funcion. Diagram: Seings: Example: Where applicable, diagram o illusrae he effecs of parameers on a characerisic curve, for example Lis of applicable seings. These include Possible seings, Mos common seings, Index and Bifields Opional example of he effecs of a paricular parameer seing. Dependency: Any condiions ha mus be saisfied in connecion wih his parameer. Also any paricular effecs, which his parameer has on oher parameer(s) or which oher parameers have on his one. Warning / Cauion / Noice / Noe: Imporan informaion which mus be observed o preven personal injury or damage o equipmen / specific informaion which should be observed in order o avoid problems / informaion which may be helpful o he user More deails: Any sources of more deailed informaion concerning he paricular parameer. Parameer Lis SINAMICS G0 6SL298-0BA-0BP0 9

15 Parameers / Quick commissioning (P000=) The following parameers are necessary for quick commissioning (P000=). No Name Access level P000 Europe / Norh America C P004 Moor volage raing C P005 Moor curren raing C P007 Moor power raing C P008 Moor cosphi raing C P009 Moor efficiency raing C P00 Moor frequency raing C P0 Moor speed raing C P05 Moor cooling CT P0640 Moor overload facor [%] CUT P0700 Selecion of command source CT P000 Selecion of frequency sepoin CT P080 Min. frequency CUT P082 Max. frequency CT P20 Ramp-up ime CUT P2 Ramp-down ime CUT P5 OFF ramp-down ime CUT P00 Conrol mode 2 CT P900 End of quick commissioning C Csa When P000 = is chosen, P000 (user access level) can be used o selec he parameers o be accessed. This parameer also allows selecion of a user-defined parameer lis for quick commissioning. A he end of he quick commissioning sequence, se P900 = o carry ou he necessary moor calculaions and clear all oher parameers (no included in P000=) o heir defaul seings. NOTE This applies only in Quick Commissioning mode. Rese o Facory defaul To rese all parameers o he facory defaul seings; he following parameers should be se as follows: Se P000 = 0 Se P0970 = NOTE The rese process akes approximaely 0 seconds o complee. Parameer Lis SINAMICS G0 0 6SL298-0BA-0BP0

16 /2004 Parameers Seven-segmen display The seven-segmen display is srucured as follows: Segmen Bi Segmen Bi The significance of he relevan bis in he display are described in he saus and conrol word parameers. Parameer Lis SINAMICS G0 6SL298-0BA-0BP0

17 Parameers /2004. Parameer Descripion r0000 Drive display Min: - Daaype: U6 Uni: - Def: - P-Group: ALWAYS Max: - Noe: Displays he user seleced oupu as defined in P0005. Pressing he "Fn" buon for 2 seconds allows he user o view he values of DC link volage, oupu frequency, oupu volage and chosen r0000 seing (defined in P0005). r0002 Drive sae Min: - Daaype: U6 Uni: - Def: - P-Group: COMMANDS Max: - Displays acual drive sae. Possible Seings: 0 Commissioning mode (P000!= 0) Drive ready 2 Drive faul acive Drive saring (DC-link precharging) 4 Drive running 5 Sopping (ramping down) Dependency: Sae visible only while precharging DC link. P000 User access level Min: CSa: CUT Daaype: U6 Uni: - Def: P-Group: ALWAYS Acive: firs confirm QuickComm.: No Max: 4 Defines user access level o parameer ses. The defaul seing (sandard) is sufficien for mos simple applicaions. Possible Seings: Sandard: Allows access ino mos frequenly used parameers. 2 Exended: Allows exended access e.g. o inverer I/O funcions. Exper: For exper use only. 4 reserved P0004 Parameer filer Min: 0 CSa: CUT Daaype: U6 Uni: - Def: 0 P-Group: ALWAYS Acive: firs confirm QuickComm.: No Max: 2 Filers available parameers according o funcionaliy o enable a more focused approach o commissioning. Possible Seings: 0 All parameers 2 Inverer Moor 7 Commands, binary I/O 8 ADC 0 Sepoin channel / RFG 2 Drive feaures Moor conrol 20 Communicaion 2 Alarms / warnings / monioring Example: P0004 = 8 specifies ha only ADC parameers will be visible. Dependency: The parameers are sub-divided ino groups (P-Group) according o heir funcionaliy. This increases he ransparency and allows a parameer o be quickly searched for. Furhermore, parameer P0004 can be used o conrol he abiliy o be visualized for he operaor panel. Value P-Group ALWAYS INVERTER MOTOR COMMANDS TERMINAL SETPOINT FUNC CONTROL COMM ALARMS Group All parameers Drive inverer parameers Moor parameers Conrol commands, digial I/O Analog inpus/oupus Sepoin channel and ramp-funcion gen. Drive inverer funcions Moor open-loop/closed-loop conrol Communicaions Fauls, warnings, monioring funcions Parameer area Parameer Lis SINAMICS G0 2 6SL298-0BA-0BP0

18 /2004 Parameers P0005 Display selecion Min: 2 CSa: CUT Daaype: U6 Uni: - Def: 2 P-Group: FUNC Acive: firs confirm QuickComm.: No Max: 4000 Selecs display for parameer r0000 (drive display). Common Seings: 2 Acual frequency 25 Oupu volage 26 DC link volage 27 Oupu curren Noice: These seings refer o read only parameer numbers ("rxxxx"). Deails: See relevan "rxxxx" parameer descripions. P000 Commissioning parameer Min: 0 CSa: CT Daaype: U6 Uni: - Def: 0 P-Group: ALWAYS Acive: firs confirm QuickComm.: No Max: 0 2 Filers parameers so ha only hose relaed o a paricular funcional group are seleced. Possible Seings: 0 Ready Quick commissioning 2 Inverer 29 Download 0 Facory seing Dependency: - Rese o 0 for inverer o run. - P000 (user access level) also deermines access o parameers. Noe: P000 = The inverer can be commissioned very quickly and easily by seing P000 =. Afer ha only he imporan parameers (e.g.: P004, P005, ec.) are visible. The value of hese parameers mus be enered one afer he oher. The end of quick commissioning and he sar of inernal calculaion will be done by seing P900 = -. Aferward parameer P000 and P900 will be rese o zero auomaically. P000 = 2 For service purposes only. P000 = 29 To ransfer a parameer file via PC ool (e.g.: STARTER) parameer P000 will be se o 29 by he PC ool. When download has been finished PC ool reses parameer P000 o zero. P000 = 0 When reseing he parameers of inverer P000 mus be se o 0. Reseing of he parameers will be sared by seing parameer P0970 =. The inverer will auomaically rese all is parameers o heir defaul seings. This can prove beneficial if you experience problems during parameer seup and wish o sar again. Parameer Lis SINAMICS G0 6SL298-0BA-0BP0

19 Parameers /2004 P004[] Sore mode Min: 0 CSa: UT Daaype: U6 Uni: - Def: 0 P-Group: - Acive: firs confirm QuickComm.: No Max: Ses he sore mode for parameers. The sore mode can be configured for all inerfaces lised under "Index". Possible Seings: 0 Volaile (RAM) Nonvolaile (EEPROM) Index: P004[0] : USS P004[] : reserved P004[2] : reserved Noe: An independen sore reques may be par of he serial communicaions (e.g. PKE bis 5-2 of USS proocol), se by a PLC or PC ools like STARTER. See he able below for an influence on he seings of P004.. Wih he BOP he parameer will always be sored in he EEPROM. 2. P004 iself will always be sored in he EEPROM.. P004 will no be changed by performing a facory rese (P000 = 0 and P097 = ). 4. P004 can be ransferred during a DOWNLOAD (P000 = 29). 5. If "Sore reques via USS = volaile (RAM)" and "P004[x] = volaile (RAM)", you can make a ransfer of all parameer values ino he nonvolaile memory via P If "Sore reques via USS" and P004[x] are no consisen, he seing of P004[x] = "sore nonvolaile (EEPROM)" has always higher prioriy. Sore reques via USS EEPROM EEPROM RAM RAM Value of P004[x] RAM EEPROM RAM EEPROM Resul EEPROM EEPROM RAM EEPROM r008 Firmware version Min: - Daaype: U2 Uni: - Def: - P-Group: INVERTER Max: - Displays version number of insalled firmware. r009 CO/BO: BOP conrol word Min: - Daaype: U6 Uni: - Def: - P-Group: COMMANDS Max: - Displays saus of operaor panel commands. Bifields: Bi00 ON/OFF 0 NO YES Bi0 OFF2: Elecrical sop 0 YES NO Bi08 JOG righ 0 NO YES Bi Reverse (sepoin inversion) 0 NO YES Bi Moor poeniomeer MOP up 0 NO YES Bi4 Moor poeniomeer MOP down 0 NO YES Noe: The following funcions can be "conneced" o individual buons: - ON/OFF, - OFF2, - JOG, - REVERSE, - INCREASE, - DECREASE Deails: The 7-segmen display of he bi-parameers (binary parameers) is explained in he Inroducion of he Parameer Lis. Parameer Lis SINAMICS G0 4 6SL298-0BA-0BP0

20 /2004 Parameers r0020 CO: Freq. sepoin before RFG Min: - Daaype: Floa Uni: Hz Def: - P-Group: CONTROL Max: - 2 Displays acual frequency sepoin (inpu for ramp funcion generaor). JOG P0 P09 P080 P082 P20 P5... Sepoin source Reverse Inhibi neg. freq. sepoin Skip frequency IfI RFG Moor conrol r078 r0020 r70 r002 CO: Ac. frequency Min: - Daaype: Floa Uni: Hz Def: - P-Group: CONTROL Max: - 2 Displays acual inverer oupu frequency (r0024) wihou slip compensaion and frequency limiaion. r0024 CO: Ac. oupu frequency Min: - Daaype: Floa Uni: Hz Def: - P-Group: CONTROL Max: - Displays acual oupu frequency (slip compensaion and frequency limiaion are included). r0025 CO: Ac. oupu volage Min: - Daaype: Floa Uni: V Def: - P-Group: CONTROL Max: - Displays [rms] volage applied o moor. r0026 CO: Ac. DC-link volage Min: - Daaype: Floa Uni: V Def: - P-Group: INVERTER Max: - Displays DC-link volage. r0027 CO: Ac. oupu curren Min: - Daaype: Floa Uni: A Def: - P-Group: CONTROL Max: - Displays esimaed rms value of moor curren [A]. r004 CO: Moor emperaure (i2) Min: - Daaype: Floa Uni: % Def: - P-Group: MOTOR Max: - 2 Noe: Displays acual moor i2 emperaure (I2 model), see parameer P06, P064) as [%]. The maximum permissible operaing emperaure (i2) of he moor is given, if he parameer r004 has reached he value of P064. In his case, he moor will aemp o reduce he moor loading as defined in P060 (moor I2 emperaure reacion). A value of 0% means ha he moor has reached is maximum permissible operaing emperaure. Parameer Lis SINAMICS G0 6SL298-0BA-0BP0 5

21 Parameers /2004 r0052 CO/BO: Ac. saus word Min: - Daaype: U6 Uni: - Def: - P-Group: COMMANDS Max: - 2 Displays firs acive saus word of inverer (bi forma) and can be used o diagnose inverer saus. Bifields: Bi00 Drive ready 0 NO YES Bi0 Drive ready o run 0 NO YES Bi02 Drive running 0 NO YES Bi0 Drive faul acive 0 NO YES Bi04 OFF2 acive 0 YES NO Bi05 OFF acive 0 YES NO Bi06 ON inhibi acive 0 NO YES Bi07 Drive warning acive 0 NO YES Bi08 Deviaion sepoin / ac. value 0 YES NO Bi09 PZD conrol 0 NO YES Bi0 f_ac >= P082 (f_max) 0 NO YES Bi Warning: Moor curren limi 0 YES NO Bi2 Moor holding brake acive 0 NO YES Bi Moor overload 0 YES NO Bi4 Moor runs righ 0 NO YES Bi5 Inverer overload 0 YES NO Dependency: r0052 Bi00 - Bi02: Sae-sequence diagram afer Power On or ON/OFF respecively: ==> see below Power ON Drive ready r0052 Bi00 ON/OFF r0052 Bi Pre-charging acive 0 Drive ready o run 0 Pulse enable Drive running r0052 Bi02 r005 Bi Ramping finished 0 r0052 Bi0 "Drive faul acive": Oupu of Bi (Faul) will be invered on digial oupu (Low = Faul, High = No Faul). Parameer Lis SINAMICS G0 6 6SL298-0BA-0BP0

22 /2004 Parameers r0052 Bi08 "Deviaion sepoin/ac. value": ==> see below ON OFF f f se Hz Hz Hz f ac Hz Hz Deviaion sepoin/ac. value r0052 Bi08 0 = NO 0 = YES r0052 Bi0 "f_ac >= P082 (f_max)" ==> see parameer P082 r0052 Bi2 "Moor holding brake acive" ==> see parameer P25 r0052 Bi4 "Moor runs righ" ==> see below ON/OFF r0054 ON Bi00 Reverse r0054 Bi f ac 0 Drive running r0052 Bi02 Moor runs righ r0052 Bi4 lef no defined las sae is displayed Deails: The 7-segmen display of he bi-parameers (binary parameers) is explained in he Inroducion of he Parameer Lis. Parameer Lis SINAMICS G0 6SL298-0BA-0BP0 7

23 Parameers /2004 r005 CO/BO: Ac. saus word 2 Min: - Daaype: U6 Uni: - Def: - P-Group: COMMANDS Max: - 2 Displays second saus word of inverer (in bi forma). Bifields: Bi00 DC brake acive 0 NO YES Bi0 f_ac > P267 (f_off) 0 NO YES Bi02 f_ac <= P080 (f_min) 0 NO YES Bi06 f_ac >= sepoin (f_se) 0 NO YES Bi07 Vdc_ac r0026 < P272 0 NO YES Bi08 Vdc_ac r0026 > P272 0 NO YES Bi09 Ramping finished 0 NO YES Noice: r005 Bi00 "DC brake acive" ==> see parameer P2 r005 Bi0 "f_ac > P267 (f_off)" r005 Bi02 "f_ac<= P080 (f_min)" r005 Bi06 "f_ac >= sepoin (f_se)" ==> see parameer P267 ==>see parameer P080 ==> see below ON OFF f f se Hz f ac r005 Bi06 f se 0 f ac r005 Bi07 "Vdc_ac r0026< P272" r005 Bi08 "Vdc_ac r0026 > P272" ==>see parameer P272 ==> see parameer P272 r005 Bi09 "Ramping finished" ==> see below ON OFF f f se f ac Ramping finished r005 Bi09 0 Deails: The 7-segmen display of he bi-parameers (binary parameers) is explained in he Inroducion of he Parameer Lis. Parameer Lis SINAMICS G0 8 6SL298-0BA-0BP0

24 /2004 Parameers r0054 CO/BO: Ac. conrol word Min: - Daaype: U6 Uni: - Def: - P-Group: COMMANDS Max: - Displays firs conrol word of inverer (in bi forma) and can be used o diagnose which commands are acive. Bifields: Bi00 ON/OFF 0 NO YES Bi0 OFF2: Elecrical sop 0 YES NO Bi02 OFF: Fas sop 0 YES NO Bi0 Pulse enable 0 NO YES Bi04 RFG enable 0 NO YES Bi05 RFG sar 0 NO YES Bi06 Sepoin enable 0 NO YES Bi07 Faul acknowledge 0 NO YES Bi08 JOG righ 0 NO YES Bi09 JOG lef 0 NO YES Bi0 Conrol from PLC 0 NO YES Bi Reverse (sepoin inversion) 0 NO YES Bi Moor poeniomeer MOP up 0 NO YES Bi4 Moor poeniomeer MOP down 0 NO YES Bi5 Hand/Auo 0 NO YES Noice: Idenical o r206 if USS is seleced as command source via P0700 or P079. Deails: The 7-segmen display of he bi-parameers (binary parameers) is explained in he Inroducion of he Parameer Lis. r0055 CO/BO: Ac. conrol word 2 Min: - Daaype: U6 Uni: - Def: - P-Group: COMMANDS Max: - Displays addiional conrol word of inverer (in bi forma) and can be used o diagnose which commands are acive. Bifields: Bi00 Fixed frequency Bi 0 0 NO YES Bi0 Fixed frequency Bi 0 NO YES Bi02 Fixed frequency Bi 2 0 NO YES Bi09 Enable DC brake 0 NO YES Bi Exernal faul 0 YES NO Noice: Idenical o r207 if USS is seleced as command source via P0700 or P079. Deails: The 7-segmen display of he bi-parameers (binary parameers) is explained in he Inroducion of he Parameer Lis. r0056 CO/BO: Saus of moor conrol Min: - Daaype: U6 Uni: - Def: - 2 P-Group: CONTROL Max: - Displays saus of moor conrol (in bi forma), which can be used o diagnose inverer saus. Bifields: Bi00 Ini. conrol finished 0 NO YES Bi0 Moor demagneizing finished 0 NO YES Bi02 Pulses enabled 0 NO YES Bi04 Moor exciaion finished 0 NO YES Bi05 Saring boos acive 0 NO YES Bi06 Acceleraion boos acive 0 NO YES Bi07 Frequency is negaive 0 NO YES Bi08 Field weakening acive 0 NO YES Bi09 Vols sepoin limied 0 NO YES Bi0 Slip frequency limied 0 NO YES Bi I-max conroller acive 0 NO YES Bi4 Vdc-max conroller acive 0 NO YES Noice: The I-max conroller (r0056 Bi) will be acivaed when he acual oupu curren (r0027) exceeds he curren limi in r0067. Deails: See descripion of seven-segmen display given in he inroducion. Parameer Lis SINAMICS G0 6SL298-0BA-0BP0 9

25 Parameers /2004 r0067 CO: Ac. oupu curren limi Min: - Daaype: Floa Uni: A Def: - P-Group: CONTROL Max: - Displays valid maximum oupu curren of inverer. Parameer r0067 is influenced/deermined by he following facors: - Raed moor curren P005 - Moor overload facor P Moor proecion in dependency of P060 - r0067 is less han or equal o maximum inverer curren r Inverer proecion in dependency of P0290 P005 Noe: P0640 Moor Moor proecion Min r0067 r0209 Inverer Inverer proecion A reducion of r0067 may indicae an inverer overload or a moor overload. Parameer Lis SINAMICS G0 20 6SL298-0BA-0BP0

26 /2004 Parameers P000 Europe / Norh America Min: 0 CSa: C Daaype: U6 Uni: - Def: 0 P-Group: QUICK Acive: firs confirm QuickComm.: Yes Max: 2 Deermines wheher power seings are expressed in [kw] or [hp] (e.g. Raed moor power P007). The defaul seings for he raed moor frequency P00 and maximum frequency P082 are also se auomaically here, in addiion o reference frequency P2000. Possible Seings: 0 Europe [kw], moor base frequency is 50 Hz Norh America [hp], moor base frequency is 60 Hz 2 Norh America [kw], moor base frequency is 60 Hz Dependency: Where: - Sop drive firs (i.e. disable all pulses) before you change his parameer. - Changing P000 reses all raed moor parameers as well as oher parameers ha depend on he raed moor parameers (see P040 - calculaion of moor parameers). Changing P000 overwries he seings of he DIP50/60 swich (locaion shown in he diagram below):. Parameer P000 has an higher prioriy han he DIP50/60 swich. 2. However, afer he inverer is powered-on again and P000 < 2, he DIP50/60 seing will ake prioriy and overwrie P000.. The DIP50/60 swich does no have any effec, if P000 = 2. DIP50/60 swich Flow char Power cycle Quick commissioning P000 = P000 = 2? yes yes P000 = 2? no no no P000 =? DIP50/60 = 50 Hz? no yes yes Power in kw Frequency 50 Hz Power in kw Frequency 60 Hz Power in hp Frequency 60 Hz P000 = 0 P000 = 2 P000 = Noice: P000 seing 2 (==> [kw], frequency defaul 60 [Hz]) is no overwrien by he seing of DIP50/60 swich (see diagram above). r027 Analogue / USS Varian Min: - Daaype: U6 Uni: - Def: - 2 P-Group: INVERTER Max: - Displays he Conrol Board Varian Type. Possible Seings: 0 Analogue USS Parameer Lis SINAMICS G0 6SL298-0BA-0BP0 2

27 Parameers /2004 r0200 Ac. power sack code number Min: - Daaype: U2 Uni: - Def: - P-Group: INVERTER Max: - Idenifies hardware varian as shown in able below. Code- No. G0 Type G0 Type Inpu Volage & Frequency Power kw Inernal Filer Hea sink Frame Size 400 6SL2-0AB-2UAx AIN AC20V 47-6Hz 0,2 no Y A SL2-0AB2-5UAx AIN AC20V 47-6Hz 0,25 no Y A 400 6SL2-0AB-7UAx AIN AC20V 47-6Hz 0,7 no Y A SL2-0AB5-5UAx AIN AC20V 47-6Hz 0,55 no Y A SL2-0AB7-5UAx AIN AC20V 47-6Hz 0,75 no Y A SL2-0KB-2UAx AIN AC20V 47-6Hz 0,2 no N A SL2-0KB2-5UAx AIN AC20V 47-6Hz 0,25 no N A SL2-0KB-7UAx AIN AC20V 47-6Hz 0,7 no N A SL2-0KB5-5UAx AIN AC20V 47-6Hz 0,55 no N A 400 6SL2-0KB7-5UAx AIN AC20V 47-6Hz 0,75 no N A 40 6SL2-0AB2-UAx AIN AC20V 47-6Hz,0 no Y B 402 6SL2-0AB2-5UAx AIN AC20V 47-6Hz,50 no Y B 40 6SL2-0AB22-2UAx AIN AC20V 47-6Hz 2,20 no Y C 404 6SL2-0AB2-0UAx AIN AC20V 47-6Hz,00 no Y C 405 6SL2-0AB-2BAx AIN AC20V 47-6Hz 0,2 Cl. A Y A 406 6SL2-0AB2-5BAx AIN AC20V 47-6Hz 0,25 Cl. A Y A 407 6SL2-0AB-7BAx AIN AC20V 47-6Hz 0,7 Cl. A Y A 408 6SL2-0AB5-5BAx AIN AC20V 47-6Hz 0,55 Cl. A Y A 409 6SL2-0AB7-5BAx AIN AC20V 47-6Hz 0,75 Cl. A Y A SL2-0KB-2BAx AIN AC20V 47-6Hz 0,2 Cl. A N A 402 6SL2-0KB2-5BAx AIN AC20V 47-6Hz 0,25 Cl. A N A SL2-0KB-7BAx AIN AC20V 47-6Hz 0,7 Cl. A N A 402 6SL2-0KB5-5BAx AIN AC20V 47-6Hz 0,55 Cl. A N A SL2-0KB7-5BAx AIN AC20V 47-6Hz 0,75 Cl. A N A SL2-0AB2-AAx AIN AC20V 47-6Hz,0 Cl. A Y B SL2-0AB2-5AAx AIN AC20V 47-6Hz,50 Cl. A Y B SL2-0AB22-2AAx AIN AC20V 47-6Hz 2,20 Cl. A Y C SL2-0AB2-0AAx AIN AC20V 47-6Hz,00 Cl. A Y C Parameer Lis SINAMICS G0 22 6SL298-0BA-0BP0

28 /2004 Parameers Code- No. G0 MLFB G0 Type Inpu Volage & Frequency Power kw Inernal Filer SL2-0AB-2UBx USS AC20V 47-6Hz 0,2 no Y A 400 6SL2-0AB2-5UBx USS AC20V 47-6Hz 0,25 no Y A 40 6SL2-0AB-7UBx USS AC20V 47-6Hz 0,7 no Y A 402 6SL2-0AB5-5UBx USS AC20V 47-6Hz 0,55 no Y A 40 6SL2-0AB7-5UBx USS AC20V 47-6Hz 0,75 no Y A 404 6SL2-0KB-2UBx USS AC20V 47-6Hz 0,2 no N A 405 6SL2-0KB2-5UBx USS AC20V 47-6Hz 0,25 no N A 406 6SL2-0KB-7UBx USS AC20V 47-6Hz 0,7 no N A 407 6SL2-0KB5-5UBx USS AC20V 47-6Hz 0,55 no N A 408 6SL2-0KB7-5UBx USS AC20V 47-6Hz 0,75 no N A 409 6SL2-0AB2-UBx USS AC20V 47-6Hz,0 no Y B SL2-0AB2-5UBx USS AC20V 47-6Hz,50 no Y B 404 6SL2-0AB22-2UBx USS AC20V 47-6Hz 2,20 no Y C SL2-0AB2-0UBx USS AC20V 47-6Hz,00 no Y C 404 6SL2-0AB-2BBx USS AC20V 47-6Hz 0,2 Cl. A Y A SL2-0AB2-5BBx USS AC20V 47-6Hz 0,25 Cl. A Y A SL2-0AB-7BBx USS AC20V 47-6Hz 0,7 Cl. A Y A SL2-0AB5-5BBx USS AC20V 47-6Hz 0,55 Cl. A Y A SL2-0AB7-5BBx USS AC20V 47-6Hz 0,75 Cl. A Y A SL2-0KB-2BBx USS AC20V 47-6Hz 0,2 Cl. A N A SL2-0KB2-5BBx USS AC20V 47-6Hz 0,25 Cl. A N A SL2-0KB-7BBx USS AC20V 47-6Hz 0,7 Cl. A N A 405 6SL2-0KB5-5BBx USS AC20V 47-6Hz 0,55 Cl. A N A SL2-0KB7-5BBx USS AC20V 47-6Hz 0,75 Cl. A N A 405 6SL2-0AB2-ABx USS AC20V 47-6Hz,0 Cl. A Y B SL2-0AB2-5ABx USS AC20V 47-6Hz,50 Cl. A Y B SL2-0AB22-2ABx USS AC20V 47-6Hz 2,20 Cl. A Y C SL2-0AB2-0ABx USS AC20V 47-6Hz,00 Cl. A Y C Noice: Parameer r0200 = 0 indicaes ha no power sack has been idenified. P020 Power sack code number Min: 0 CSa: C Daaype: U6 Uni: - Def: 0 P-Group: INVERTER Acive: firs confirm QuickComm.: No Max: 6555 Hea sink Frame Size Confirms acual power sack idenified. r0206 Raed inverer power [kw] / [hp] Min: - Daaype: Floa Uni: - Def: - P-Group: INVERTER Max: - Displays nominal raed moor power from inverer. Dependency: Value is displayed in [kw] or [hp] depending on seing for P000 (operaion for Europe / Norh America). r0206 [hp] 0.75 r0206 [kw] Parameer Lis SINAMICS G0 6SL298-0BA-0BP0 2

29 Parameers /2004 r0207[] Raed inverer curren Min: - Daaype: Floa Uni: A Def: - P-Group: INVERTER Max: - Indicaes he raed inverer curren. Index: r0207[0] : Raed inverer curren r0207[] : Raed VT curren r0207[2] : Raed CT curren Noes: VT (variable orque) and CT (consan orque) specify he overload capabiliy (CT/VT applicaion) of he inverer. The definiion of he raed as well as he overload and base load values depend on he inverer ype and inverer power. The differen values can be aken from he appropriae Caalog or are saved in he inverer. The VT raed curren r0207[] or CT raed curren r0207[2] represen he maching 4-pole Siemens IEC sandard moor for he seleced load duy cycle (refer o he diagram). Parameers r0207[] or r0207[2] are used as defaul values for P005 as a funcion of he CT/VT applicaion (load duy cycle). If r0207[] = r0207[2], hen i is no possible o make a differeniaion beween a CT/VT applicaion. Inverer curren/power % r % r0207[0] 00 % 85 % Raed inverer curren (coninuous) Base load curren (wih overload capabiliy) Shor-ime curren 60 s 00 s Overload in operaion is only possible if, before he overload condiion, he load curren was less han he raed curren. For drives, which mus be able o handle overload condiions, i is firs necessary o define a base load curren for he required load. If he full overload capabiliy is used, hen his is deeced using an I² monioring and he power module is proeced as a funcion of parameer P0290. The above diagram refers o he inverer curren. Since he moor raed curren of a maching 4-pole Siemens sandard moor is smaller as he inverer curren moor overhea will occur when his inverer load cycle is applied o he maching moor. r0209 Maximum inverer curren Min: - Daaype: Floa Uni: A Def: - P-Group: INVERTER Max: - Displays maximum oupu curren of inverer. Dependency: Parameer r0209 depends on he deraing which is affeced by pulse frequency P800, ambien emperaure and aliude. The daa of deraion is given in he OPERATING INSTRUCTION. Parameer Lis SINAMICS G0 24 6SL298-0BA-0BP0

30 /2004 Parameers P0290 Inverer overload reacion Min: 0 CSa: CT Daaype: U6 Uni: - Def: 0 P-Group: INVERTER Acive: firs confirm QuickComm.: No Max: Selecs reacion of inverer o an inernal over-emperaure. Possible Seings: 0 Reduce oupu frequency Trip (F0004 / F0005) Dependency: Following physical values influence he inverer overload proecion (see diagram): - hea sink emperaure - inverer I² Inverer Inverer overload reacion P0290 i 2 i_max conrol A0505 F0005 Hea Sink Temperaure F0004 Noice: P0290 = 0: - Reducion of oupu frequency is only effecive if he load is also reduced. This is for example valid for variable orque applicaions wih a quadraic orque characerisic as pumps or fans. - In seings P0290 = 0, he I-max conroller will ac upon he oupu curren limi (r0067) in case of overemperaure. A rip will always resul, if he acion aken does no sufficienly reduce inernal emperaure. P0295 Inverer fan off delay ime Min: 0 CSa: CUT Daaype: U6 Uni: s Def: 0 P-Group: TERMINAL Acive: firs confirm QuickComm.: No Max: 600 Noe: Defines inverer fan swich off delay ime in seconds afer drive has sopped. Seing o 0, inverer fan will swich off when he drive sops, ha is no delay. SINAMICS G0 FS A has no fan. Parameer Lis SINAMICS G0 6SL298-0BA-0BP0 25

31 Parameers /2004 P004 Raed moor volage Min: 0 CSa: C Daaype: U6 Uni: V Def: 20 P-Group: MOTOR Acive: firs confirm QuickComm.: Yes Max: 2000 Nominal moor volage [V] from raing plae. Following diagram shows a ypical raing plae wih he locaions of he relevan moor daa. Line supply volage SINAMICS G0 AC 20 V X AC 20 V - AC 400 V - AC 560 V Dependency: Changeable only when P000 = (quick commissioning). Cauion: The inpu of raing plae daa mus correspond wih he wiring of he moor (sar / dela). This means, if dela wiring is used for he moor, dela raing plae daa has o be enered. IEC Moor - W2 U U2 V V2 W W2 U U2 V V2 W U U V W Dela connecion V W Sar connecion Noe: e.g.: Vols 20 V (Dela connecion) / 400 V (Sar connecion) Defaul value is depending on inverer ype and is raing daa. Parameer Lis SINAMICS G0 26 6SL298-0BA-0BP0

32 /2004 Parameers P005 Raed moor curren Min: 0.0 CSa: C Daaype: Floa Uni: A Def: (x) P-Group: MOTOR Acive: firs confirm QuickComm.: Yes Max: Nominal moor curren [A] from raing plae - see diagram in P004. Dependency: - Changeable only when P000 = (quick commissioning). Noe: The maximum value of P005 depends on he maximum inverer curren r0209 and he moor ype: Asynchronous moor : P005 max, asyn = 2 r0209 I is recommended ha he raio of P005 (raed moor curren) and r0207 (raed inverer curren) should no be lower han: V/f: 8 P005 r0207 When he relaion of he nominal moor curren P005 and half of he maximal inverer curren (r0209) exceeds,5 an addiional curren deraing is applied. This is necessary o proec he inverer from harmonic curren waves. r0209 I max,inv 0.7 r P005 r0209 (x) Defaul value is depending on inverer ype and is raing daa and he maching 4 pole Siemens sandard moor. P007 Raed moor power Min: 0.0 CSa: C Daaype: Floa Uni: - Def: (x) P-Group: MOTOR Acive: firs confirm QuickComm.: Yes Max: Nominal moor power [kw/hp] from raing plae. Dependency: - If P000 =, values will be in [hp] - see diagram P004 (raing plae). - Changeable only when P000 = (quick commissioning). - (x) Defaul value is depending on inverer ype and is raing daa and he maching 4 pole Siemens sandard moor. P008 Raed moor cosphi Min: CSa: C Daaype: Floa Uni: - Def: P-Group: MOTOR Acive: firs confirm QuickComm.: Yes Max:.000 Nominal moor power facor (cosphi) from raing plae - see diagram P004. Dependency: - Changeable only when P000 = (quick commissioning). - Visible only when P000 =. - Applicable only if he moor power is enered in [kw]) i.e. P000= 0 or 2 In his case P009 is no relevan. - Seing 0 causes inernal calculaion of value. Parameer Lis SINAMICS G0 6SL298-0BA-0BP0 27

33 Parameers /2004 P009 Raed moor efficiency Min: 0.0 CSa: C Daaype: Floa Uni: % Def: 0.0 P-Group: MOTOR Acive: firs confirm QuickComm.: Yes Max: 99.9 Nominal moor efficiency in [%] from raing plae. Dependency: - Changeable only when P000 = (quick commissioning). - Visible only when P000 =. - Applicable only if he moor power is enered in [hp]) i.e. P000 = In his case P008 is no relevan. - Seing 0 causes inernal calculaion of value. Noe: P009 = 00 % corresponds o superconducing. Deails: See diagram in P004 (raing plae). P00 Raed moor frequency Min: 2.00 CSa: C Daaype: Floa Uni: Hz Def: P-Group: MOTOR Acive: firs confirm QuickComm.: Yes Max: Nominal moor frequency [Hz] from raing plae. Dependency: - Changeable only when P000 = (quick commissioning). - Pole pair number recalculaed auomaically if parameer is changed. Deails: See diagram in P004 (raing plae) P0 Raed moor speed Min: 0 CSa: C Daaype: U6 Uni: /min Def: (x) P-Group: MOTOR Acive: firs confirm QuickComm.: Yes Max: Nominal moor speed [rpm] from raing plae. Dependency: - Changeable only when P000 = (quick commissioning). - Seing 0 causes inernal calculaion of value. - Slip compensaion in V/f conrol requires raed moor speed for correc operaion. - Pole pair number recalculaed auomaically if parameer is changed. (x) Defaul value depends on he inverer ype and is raing daa and he maching 4 pole Siemens sandard moor. Deails: See diagram in P004 (raing plae) r00 Raed moor slip Min: - Daaype: Floa Uni: % Def: - P-Group: MOTOR Max: - Displays nominal moor slip in [%] relaive o P00 (raed moor frequency) and P0 (raed moor speed). P05 Moor cooling Min: 0 CSa: CT Daaype: U6 Uni: - Def: 0 P-Group: MOTOR Acive: firs confirm QuickComm.: Yes Max: Selecs moor cooling sysem used. Possible Seings: 0 Self-cooled: Using shaf mouned fan aached o moor Force-cooled: Using separaely powered cooling fan P040 Calculaion of moor parameers Min: 0 CSa: CT Daaype: U6 Uni: - Def: 0 P-Group: MOTOR Acive: firs confirm QuickComm.: No Max: Calculaes various moor parameers (see able below). This parameer is required during commissioning o opimize inverer performance. Possible Seings: 0 No calculaion Complee parameerizaion Noe: P040 = : - P046 Magneizaion ime - P047 Demagneizaion ime - P050 Saor resisance (line-o-line) - P6 Boos end frequency - P2000 Reference frequency Parameer Lis SINAMICS G0 28 6SL298-0BA-0BP0