Thyristors 6 Amp Sensitive & Standard SCRs. Sxx06xSx & Sxx06x Series

Transcription

1 Sxx06xSx & Sxx06x Series RoHS Description This Sxx06x SCR series is ideal for uni-directional switch applications such as phase control, heating, motor speed controls, converters/rectifiers and capacitive discharge ignitions. These SCRs have a low gate current trigger level of 0.2 to 15 ma at approximately 1.5V, with a sensitive version of this series having a gate trigger current less than 500µA. The sensitive gate SCR version is easily triggered by sense coils, proximity switches, and microprocessors. Features & Benefits Agency Approval Agency Agency File Number Halogen free and RoHS compliant Glass passivated junctions Voltage capability up to 0 V Surge capability up to A at 60 Hz half cycle L-Package is UL recognized for 2500Vrms L Package: E71639 Applications Main Features Symbol Value Unit I T(RMS) 6 A RM /V RRM 400 to 0 V I GT 0.2 to 15 ma Typical applications are capacitive discharge systems for strobe lights, nailers, staplers and gas engine ignition. Also, AC control & rectification for power tools, home/brown goods and white goods appliances and 2-wheeler rectifier/ battery regulators. Internally constructed isolated packages are offered for ease of heat sinking with highest isolation voltage. Schematic Symbol Additional Information A K Datasheet Resources Samples G

2 Absolute Maximum Ratings Sensitive SCRs Symbol Parameter Test Conditions Value Unit I T(RMS) I T(AV) I TSM RMS on-state current Average on-state current Peak non-repetitive surge current Sxx06LSy T C = 80 C Sxx06NSy Sxx06RSy Sxx06DSy Sxx06VSy T C = 95 C Sxx06LSy T C = 80 C Sxx06NSy Sxx06RSy Sxx06DSy Sxx06VSy TC = 95 C single half cycle; f = 50Hz; (initial) = 25 C single half cycle; f = 60Hz; (initial) = 25 C 6 A 3.8 A I 2 t I 2 t Value for fusing t p = 8.3 ms 41 A 2 s di/dt Critical rate of rise of on-state current f = 60Hz; = 110 C A/μs I GTM Peak gate current = 110 C 1 A P G(AV) Average gate power dissipation = 110 C 0.1 W T stg Storage temperature range -40 to 150 C Operating junction temperature range -40 to 110 C Note: xx = voltage, y = sensitivity 83 A Absolute Maximum Ratings Standard SCRs Symbol Parameter Value Unit I T(RMS) I T(AV) I TSM RMS on-state current Average on-state current Peak non-repetitive surge current Sxx06L T C = C Sxx06N Sxx06R Sxx06D Sxx06V T C = 110 C Sxx06L T C = C Sxx06N Sxx06R Sxx06D Sxx06V T C = 110 C single half cycle; f = 50Hz; (initial) = 25 C single half cycle; f = 60Hz; (initial) = 25 C 6 A 3.8 A I 2 t I 2 t value for fusing t p = 8.3 ms 41 A 2 s di/dt Critical rate-of-rise of on-state current f = 60Hz; =125 C A/μs I GTM Peak gate current = 125 C 2 A P G(AV) Average gate power dissipation = 125 C 0.5 W T stg Storage temperature range -40 to 150 C Note: xx = voltage Operating junction temperature range -40 to 125 C 83 A

3 Electrical Characteristics ( = 25 C, unless otherwise specified) Sensitive SCRs Symbol Test Conditions Value Sxx06xS2 Sxx06xS3 Unit I GT = 6V R L = Ω MAX μa V GT = 6V R L = Ω MAX. 0.8 V dv/dt = RM ; R GK = 1kΩ; = 110 C TYP. 8 V/μs V GD = RM R L = 3.3 kω = 110 C MIN. 0.2 V V GRM I GR = 10μA MIN. 6 V I H I T = 20mA (initial) MAX. 6 8 ma t q I T = 2A; t p = 50µs; dv/dt=5v/µs; di/dt=-30a/µs MAX μs t gt I G = 2 x I GT PW = 15µs I T = 12A TYP. 4 5 μs Note: xx = voltage, x = package Electrical Characteristics ( = 25 C, unless otherwise specified) Standard SCRs Symbol Test Conditions Value Sxx06x Unit I GT = 12V R L = 60 Ω MAX. 15 ma V GT = 12V R L = 60 Ω MAX. 1.5 V 400V 350 = RM ; gate open; = C 600V V 250 dv/dt 0V MIN. V/μs 400V 250 = RM ; gate open; = 125 C 600V V 200 V GD = RM R L = 3.3 kω = 125 C MIN. 0.2 V I H I T = 200mA (initial) MAX. 30 ma t q I T = 2A; t p = 50µs; dv/dt=5v/µs; di/dt=-30a/µs MAX. 35 μs t gt I G = 2 x I GT PW = 15µs I T = 12A TYP. 2 μs Note: xx = voltage, x = package

4 Static Characteristics Symbol Test Conditions Value Unit V TM I T = 12A; t p = 380 µs MAX. 1.6 V Sxx06xyy = 25 C V 5 = 110 C V 250 I DRM / I RRM RM = V RRM = 25 C V 10 0V MAX. 20 μa Sxx06x = C V 200 0V 3000 = 125 C V 500 Note: xx = voltage, x = package, yy = sensitivity Thermal Resistances Symbol Parameter Value Unit Sxx06RSy / Sxx06NSy 2.6 Sxx06LSy 4.3 Sxx06VSy 2.4 R θ(j-c) Junction to case (AC) Sxx06DSy 1.8 Sxx06R / Sxx06N 2.5 C/W Sxx06L 4.0 Sxx06V 2.3 Sxx06D 1.7 Sxx06RSy 40 Sxx06LSy 65 R θ(j-a) Junction to ambient Sxx06VSy 85 Sxx06R 40 C/W Sxx06L 50 Sxx06V 70 Note: xx = voltage, y = sensitivity

5 Figure 1: Normalized DC Gate Trigger Current vs. Junction Temperature (Sensitive SCR) Figure 2: Normalized DC Gate Trigger Current vs. Junction Temperature (Standard SCR) Ratio of I GT /I GT ( =25ºC) Ratio of I GT / I GT ( = 25ºC) Junction Temperature ( ) - (ºC) Junction Temperature ( ) - (ºC) Figure 3: Normalized DC Gate Trigger Voltage vs. Junction Temperature Figure 4: Normalized DC Holding Current vs. Junction Temperature Ratio of V GT / V GT ( = 25ºC) Ratio of I H / I H ( = 25ºC) Junction Temperature ( ) - (ºC) Junction Temperature ( ) - (ºC) Figure 5: On-State Current vs. On-State Voltage (Typical) Figure 6: Power Dissipation (Typical) vs. RMS On-State Current = 25 C 6 5 Instantaneous On-State Current (i T ) -Amps Average On-State Power Dissipation [P D(AV) ] - (Watts) Instantaneous On-State Voltage (v T ) - Volts RMS On-State Current [I T(RMS) ] - (Amps)

6 Figure 7: Maximum Allowable Case Temperature vs. RMS On-State Current Figure 8: Maximum Allowable Case Temperature vs. Average On-State Current Maximum Allowable Case Temperature (T C ) - º C Sxx06RSy/ Sxx06NSy Sxx06RSy Sxx06DSy Sxx06R/Sxx06N Sxx06D Sxx06V 95 Sxx06LSy 90 CURRENT WAVEFORM: Sinsuoidal LOAD: Resistive or Inductive 85 CONDUCTION ANGLE: 180 FREE AIR RATING RMS On-State Current [I T(RMS) ] - Amps Sxx06L Maximum Allowable Case Temperature (T C ) - ºC Sxx06RSy/ Sxx06NSy Sxx06RSy Sxx06DSy Sxx06VSy CURRENT WAVEFORM: Sinsuoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180 FREE AIR RATING Sxx06R/Sxx06N Sxx06D Sxx06V Average On-State Current [I T(AVE) ] - Amps Sxx06L Sx06LSy 4 Figure 9: Maximum Allowable Ambient Temperature vs. RMS On-State Current Figure 10: Maximum Allowable Ambient Temperature vs. Average On-State Current Maximum Allowable Temperature (T A ) - ºC Sxx06LSy Sxx06RSy Sxx06VSy Sxx06R Sxx06L CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180 FREE AIR RATING Sxx06V Maximum Allowable Ambient Temperature (T A ) - ºC Sxx06RSy Sxx06LSy Sxx06VSy Sxx06R CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180 FREE AIR RATING Sxx06L Sxx06V RMS On-State Current [I T(RMS) ] - Amps Average On-State Current [I T(AVE) ] - Amps 1.5 Note: xx = voltage, y = sensitivity Figure 11: Peak Capacitor Discharge Current Figure 12: Peak Capacitor Discharge Current Derating Peak Discharge Current (I TM ) - Amps I TRM Normalized Peak Current Sensitive SCR Standard SCR 0.2 t W Pulse Current Duration (t w ) - ms Case Temperature (T C ) - ºC

7 Figure 13-1: Typical DC Gate Trigger Current with R GK vs. Junction Temperature for S6008DS2 Figure 13-2: Typical DC Gate Trigger Current with R GK vs. Junction Temperature for SS6008DS3 Figure 14-1: Typical DC Holding Current with R GK vs. Junction Temperature for S6008DS2 Figure 14-2 Typical DC Holding Current with R GK vs. Junction Temperature for SS6008DS3 Figure 15-1: Typical Static dv/dt with R GK vs. Junction Temperature for S6008DS2 Figure 15-2 Typical Static dv/dt with R GK vs. Junction Temperature for SS6008DS3

8 Figure 16-1: Typical Static dv/dt with R GK vs. Junction Temperature for S6008DS2 Figure 16-2 Typical Static dv/dt with R GK vs. Junction Temperature for SS6008DS3 Figure 17: Surge Peak On-State Current vs. Number of Cycles Peak Surge (Non-repetitive) On-State Current (I TSM ) AMPS 10 SUPPLY FREQUENCY: 60 Hz Sinusoidal LOAD: Resistive RMS On-State Current: [I T(RMS) ]: Maximum Rated Value at Specified Case Temperature Notes: 1. Gate control may be lost during and immediately following surge current interval. 2. Overload may not be repeated until junction temperature has returned to steady-state rated value Surge Current Duration -- Full Cycles

9 Temperature Thyristors Soldering Parameters Reflow Condition - Temperature Min (T s(min) ) 150 C Pb Free assembly T P Ramp-up t P Pre Heat - Temperature Max (T s(max) ) 200 C - Time (min to max) (t s ) secs Average ramp up rate (Liquidus Temp) (T L ) to peak 5 C/second max T L T S(max) T S(min) Preheat t L Ramp-down T S(max) to T L - Ramp-up Rate 5 C/second max t S - Temperature (T L ) (Liquidus) 217 C Reflow - Temperature (t L ) seconds Peak Temperature (T P ) /-5 C 25 time to peak temperature Time Time within 5 C of actual peak Temperature (t p ) seconds Ramp-down Rate 5 C/second max Time 25 C to peak Temperature (T P ) 8 minutes Max. Do not exceed 280 C Physical Specifications Terminal Finish Body Material Lead Material % Matte Tin-plated UL recognized epoxy meeting flammability rating 94V-0 Copper Alloy Design Considerations Careful selection of the correct component for the application s operating parameters and environment will go a long way toward extending the operating life of the Thyristor. Good design practice should limit the maximum continuous current through the main terminals to 75% of the component rating. Other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. Overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. Correct mounting, soldering, and forming of the leads also help protect against component damage.

10 Environmental Specifications Test AC Blocking Temperature Cycling Temperature/ Humidity High Temp Storage Low-Temp Storage Resistance to Solder Heat Solderability Lead Bend Specifications and Conditions MIL-STD-750, M-1040, Cond A Applied Peak AC 125 C for 8 hours MIL-STD-750, M-1051, cycles; -40 C to +150 C; 15-min dwell-time EIA / JEDEC, JESD22-A101 8 hours; 320V - DC: 85 C; 85% rel humidity MIL-STD-750, M-1031, 8 hours; 150 C 8 hours; -40 C MIL-STD-750 Method 2031 ANSI/J-STD-002, category 3, Test A MIL-STD-750, M-2036 Cond E Product Selector Voltage Part Number 400V 600V 800V 0V Gate Sensitivity Type Package Sxx06RS2 X X 0.2mA Sensitive SCR TO-220R Sxx06LS2 X X 0.2mA Sensitive SCR TO-220L Sxx06VS2 X X 0.2mA Sensitive SCR TO-251 Sxx06DS2 X X 0.2mA Sensitive SCR TO-252 Sxx06RS3 X X 0.5mA Sensitive SCR TO-220R Sxx06LS3 X X 0.5mA Sensitive SCR TO-220L Sxx06VS3 X X 0.5mA Sensitive SCR TO-251 Sxx06DS3 X X 0.5mA Sensitive SCR TO-252 Sxx06R X X X X 15mA Standard SCR TO-220R Sxx06L X X X X 15mA Standard SCR TO-220L Sxx06V X X X X 15mA Standard SCR TO-251 Sxx06D X X X X 15mA Standard SCR TO-252 Note: xx = voltage

11 Dimensions TO-251AA (V/I-Package) V/I-PAK Through Hole Anode E D T C MEASURING POINT H J AREA: IN Inches Millimeters Dimension Min Typ Max Min Typ Max A A B B C D E C P Q R S K F G H I J Cathode Anode GATE I G F L K L P Q R S Dimensions TO-252AA (D-Package) D-PAK Surface Mount Anode A B E D T C MEASURING POINT Dimension Inches Millimeters Min Typ Max Min Typ Max A B C Cathode Anode I G P Q GATE F O L M N AREA: IN 2 K J H C D E F G H I J K L M N O P Q

12 Dimensions TO-220AB (R-Package) Non-Isolated Mounting Tab Common with Center Lead E B C D A ANODE T C MEASURING POINT O P AREA (REF.) 0.17 IN Dimension Inches Millimeters Min Max Min Max A B C D E G F L H R NOTCH IN GATE LEAD TO ID. NON-ISOLATED TAB F G H J CATHODE ANODE K J GATE N M Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). K L M N O P R Dimensions TO-220AB (L-Package) Isolated Mounting Tab E A T C MEASURING POINT AREA (REF.) 0.17 IN 2 O P Dimension Inches Millimeters Min Max Min Max B C D A B C D E F F G L H R G H J CATHODE ANODE K J GATE N M Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). K L M N O P R

13 Dimensions TO-263 (N Package) D 2 Pak Surface Mount Dimension Inches Millimeters Min Max Min Max A B C D E F G H J K S V U W Packing Options Part Number Marking Weight Packing Mode Base Quantity Sxx06L/RyyTP Sxx06L/Ryy 2.2 g Tube 500 (50 per tube) Sxx06DyyTP Sxx06Dyy 0.3 g Tube 750 (75 per tube) Sxx06DyyRP Sxx06Dyy 0.3 g Embossed Carrier 2500 Sxx06VyyTP Sxx06Vyy 0.4 g Tube 750 (75 per tube) Sxx06L/RTP Sxx06L/R 2.2 g Tube 500 (50 per tube) Sxx06DTP Sxx06D 0.3 g Tube 750 (75 per tube) Sxx06DRP Sxx06D 0.3 g Embossed Carrier 2500 Sxx06VTP Sxx06V 0.4 g Tube 750 (75 per tube) Sxx06NyyRP Sxx6Nyy 1.6g Embossed Carrier 500 Sxx06NyyTP Sxx6Nyy 1.6g Tube 500 (50 per tube) Sxx06NRP Sxx6N 1.6g Embossed Carrier 500 Sxx06NTP Sxx6N 1.6g Tube 500 (50 per tube) Note: xx = Voltage/10; yy = Sensitivity

14 Thyristors TO-202 Type 1 (F Package) TO-252 Embossed Carrier Reel Pack (RP) Specs Meets all EIA Standards (4.0) Gate DIA (1.5) Cathode Part Marking System S6006F1 yxxxx TO-251AA- (V Package) TO-252AA- (D Package) TO-251AA (V Pac TO-252AA (D Pac YMLDD S6006DS2 S6006DS2 S6006DS (16.0) (13.3) * XXXXXX XX DC XXXXXX XX DC XXXXXX XX DC XXXXXX * Cover tape (13.0) Arbor Hole Diameter (8.0) (330.0) Anode Dimensions are in inches (and millimeters). YMLDD YMLDD Date Code Marking Y:Year Code M: Month Code L: Location Code DD: Calendar Code TO-263 AA (N Package) TO-220 AB - (L and R Package) S6006RS2 YM 0.64 (16.3) Direction of Feed Date Code Marking Y:Year Code M: Month Code XXX: Lot Trace Code Part Numbering System S L S2 56 COMPONENT DEVICE TYPE S: SCR VOLTAGE RATING 40: 400V 60: 600V 80: 800V K0: 0V CURRENT RATING 06: 6A LEAD FORM DIMENSIONS xx: Lead Form Option SENSITIVITY & TYPE Sensitive SCR: S2: 200µA S3: 500µA Standard SCR: (blank): 15mA PACKAGE TYPE L: TO-220 Isolated R: TO-220 Non-Isolated V: TO-251 (V/I-Pak) D: TO-252 (D-Pak) N: TO-263 (D2-Pak)