AQ3041 Series 0.5pF 20kV Unidirectional Discrete TVS

Transcription

1 AQ304 Series 0.5pF 20kV Unidirectional Discrete TVS RoHS Pb GREEN Description The AQ304 includes low capacitance rail to rail diodes with an additional Zener diode to provide protection for electronic equipment that may experience destructive electrostatic discharges (ESD). These robust diodes can safely absorb repetitive ESD strikes above the maximum level specified in IEC international standard (±20kV contact discharge) without performance degradation. The low loading capacitance makes it ideal for protecting high speed data lines such as HDMI, DVI, USB2.0, USB3.0 and esata. Pinout SOD882 2 (AEC-Q0 qualified) Functional Block Diagram Features ESD protection of ±20kV contact discharge, ±30kV air discharge, (IEC ) EFT protection, IEC , 40A (t p =5/50ns) Lightning Protection, IEC nd edition, 3A (t p =8/20µs) Low capacitance of V R =0V Low leakage current of 0.μA at 5V Small SOD882 packaging helps save board space AEC-Q0 qualified Halogen free, lead free and RoHS compliant Moisture Sensitivity Level(MSL -) Life Support Note: Not Intended for Use in Life Support or Life Saving Applications The products shown herein are not designed for use in life sustaining or life saving applications unless otherwise expressly indicated. 2 Applications Tablets Ultrabook ereader Smart Phones Digital Cameras MP3/ PMP Set Top Boxes Portable Medical Automotive Applications HDMI Application Example USB3.0 Application Example HDMI Port D2+ *Packages are shown as transparent HDMI Chipset USB Port VBUS USB Controller D2- D+ D- AQ003 D0+ D0- *Packages are shown as transparent CLK+ D+ CLK- D- IC IC SSTX+ CEC SCL AQ304 (x8) SSTX- SSRX+ SSRX- SDA HPD PWR Signal Ground SP3002 AQ304 (x6)

2 Absolute Maximum Ratings Symbol Parameter Value Units Peak Current (t p =8/20μs) 3.0 A T OP Operating Temperature -40 to 50 C T STOR Storage Temperature -55 to 50 C Thermal Information Parameter Rating Units Maximum Junction Temperature 50 C Maximum Lead Temperature (Soldering 30s) 260 C CAUTION: Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the component. This is a stress only rating and operation of the component at these or any other conditions above those indicated in the operational sections of this specification is not implied. Electrical Characteristics (T OP =25ºC) Parameter Symbol Test Conditions Min Typ Max Units Reverse Standoff Voltage V RWM 5 V Reverse Leakage Current I LEAK V R =5V with pin at GND µa Clamp Voltage V C =A, t p =8/20µs, Fwd 9.2 V =2A, t p =8/20µs, Fwd 0.0 V ESD Withstand Voltage V ESD IEC (Contact) ±20 kv IEC (Air) ±30 kv Dynamic Resistance 2 R DYN TLP, t P =00ns, I/O to GND 0.3 Ω Diode Capacitance C I/O-I/O Reverse Bias=0V, f= MHz 0.5 pf Note: Parameter is guaranteed by design and/or component characterization. 2 Transmission Line Pulse (TLP) with 00ns width, 2ns rise time, and average window t=70ns to t2= 90ns Normalized Capacitance vs. Reverse Voltage 8/20μs Pulse Waveform.5 Capacitance (pf) Bias Voltage (V) Percent of 0% 00% 90% 80% 70% 60% 50% 40% 30% 20% 0% 0% Time (μs)

3 Temperature TVS Diode Arrays (SPA Diodes) Transmission Line Pulsing(TLP) Plot TLP Current (A) TLP Voltage (V) Soldering Parameters Reflow Condition Pb Free assembly - Temperature Min (T s(min) ) 50 C Pre Heat - Temperature Max (T s(max) ) 200 C - Time (min to max) (t s ) secs Average ramp up rate (Liquidus) Temp (T L ) to peak 3 C/second max T S(max) to T L - Ramp-up Rate 3 C/second max - Temperature (T L ) (Liquidus) 27 C Reflow - Temperature (t L ) seconds Peak Temperature (T P ) /-5 C Time within 5 C of actual peak Temperature (t p ) seconds Ramp-down Rate 6 C/second max Time 25 C to peak Temperature (T P ) 8 minutes Max. Do not exceed 260 C Part Numbering System Automotive Grade TVS Diode Arrays (SPA Diodes) Series Number of Channels AQ E T G G= Green T= Tape & Reel Package E: SOD882 T P T L T S(max) T S(min) 25 t S Preheat Ramp-up time to peak temperature Product Characteristics Lead Plating Lead Material Substrate material Body Material Flammability t P t L Ramp-down Time Pre-Plated Frame Copper Alloy Silicon Molded Epoxy UL Recognized epoxy meeting flammability rating V-0. Notes :. All dimensions are in millimeters 2. Dimensions include solder plating. 3. Dimensions are exclusive of mold flash & metal burr. 4. Blo is facing up for mold and facing down for trim/form, i.e. reverse trim/form. 5. Package surface matte finish VDI -3. Part Marking System Critical Zone TL to TP PIN PIN 2 T

4 Ordering Information Part Number Package Marking Min. Order Qty. Packaging Option P0/P Packaging Specification AQ304-0ETG SOD882 T 0000 Tape & Reel 8mm tape/7 reel 4mm/2mm EIA RS-48 Package Dimensions SOD882 T D Top Cover Tape 3 REF WL E A P0 A P2 Φ2:.55± E Recommended Soldering Pad Layout F Package SOD882 Symbol JEDEC MO-236 Millimeters Inches Min Max Min Max A b L e D E B0 b K0 P Φ: 0.40±0.05 e W Embossed Carrier Tape & Reel Specification SOD882 R K M N H S Symbol Millimetres Inches Min Max Min Max User Feeding Direction ComponentOrientationinTape Pin W Pin Location A B C dø E F P P P W mm TAPE AND REEL Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at

5 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Littelfuse: AQ304-0ETG