SPECIFICATION FOR APPROVAL

Transcription

1 Ⅰ. onfiguration and dimensions: ' 'S WG NO. SF090 P - REV PGE H I.0 ref..70 ref. F E.0 ref ref. ( P Pattern ) Unit:m/m ' E F H I 9.00± typ. 5.0±0..70± 5. typ..5 typ. 0. typ..75 typ. 0.0 typ. Ⅱ. Schematic diagram: N N Ⅲ. escription: " " : Polarity a. Ferrite toroidal core construction. b. Enamelled copper wire:h class c. Product weight: 0.7g(ref.) d. Moisture sensitivity Level e. Products comply with RoHS' requirements f. Halogen free available Ⅳ. General specification: a. Storage temp.: b. Operating temp.: (Temp. rise included) c. Resistance to solder heat:. 0 secs. Temperature ( ) Temperature Rising rea +.0 / sec max. Preheat rea ~ 00 / 60 ~ 0sec 60sec~0sec Peak Temp: max. Max. Peak Temp - 5 :0sec max. Max time above 7 :60sec~sec max. 00 Time ( seconds ) Reflow rea +.0 / sec max. 60sec max. 60sec~sec Forced ooling rea -(.0 ~ 5.0) / sec max. Peak Temperature: 7 00 R-00

2 Ⅴ. Electrical characteristics: 'S WG NO. SF090 P - REV PGE WG No. L 00KHz,0. Vrms ( μh ) LL (-) ( μh 00KHz,0. Vrms typ. ( - short ) R ( Ω ) max. Rated urrent max. () Impedance ( Ω ) min. Freq. Range ( MHz ) Winding SF0900YP -.0±5% ~00 ifilar SF090YP - 5.0±5% ~ Sector SF090YP - 5.0±5% SF0900YP ±5% ~00 Sector 700 ~0 Sector SF0907YP ±5% ~5 ifilar SF0900YP ±5% ~0 ifilar SF0907YP ±5% ~ ifilar ). :Packaging information: ode ). "- ":Reference code ). Electrical specifications at 5 ). Rated voltage 80 Vdc / Vac 5). Hi-Pot ( N-N ): Vac / 60 Hz, m / sec. 6). Rated current base on Temp. rise 0 max. R-00

3 Ⅵ. urve: 'S WG NO. SF090 P - REV PGE Impedance VS. Frequency Y Y Impedance(Ω) 000 0Y 7Y Y 0Y Measuring circuit : 00 0Y Frequency(MHz) Network nalyzer Impedance VS. Frequency Insertion Loss(d) Y 0Y -5 Y -0 7Y Y -5 0Y -0 7Y Frequency(MHz) Measuring circuit : Network nalyzer R-00

4 Ⅶ. Packaging information: 'S WG NO. SF090 P - REV PGE ( ) onfiguration T.0± over Tape N G Embossed carrier End P:8 m/m m/m arrier tape width : Start Leader no component 00 m/m min. omponents Trailer no component 00 m/m min User direction of feed ( ) imensions Unit:m/m Style G N T ±0.8 ± ( ) Q'TY & G.W. Per package ode Q'TY (pcs) Inner : Reel G.W. (gw) Style Q'TY (pcs) Outer : arton G.W. (Kg) Size (cm), , x 7 x R-00

5 Ⅷ. Reliability test: 'S WG NO. SF090 P - REV PGE 5.High Temperature Exposure.Temperature ycling.iased Humidity Test.Operational Life 5.Exeternal Visual 6.Physical imensions 7.Resistance to solvents 8.Vibration Test 9.Resistance To Soldering Heat Test 0.Rated current.temperature rise.over load.solderability Test.Electrical haracteriazation 5.Withstanding Voltage Test 6.rop Item 7.Terminal Strength Test Reference documents MIL-ST-0 Method 08 JES Method J-0 MIL-ST-0 Method 0 MIL-PRF-7 MIL-PRF-7 MIL-PRF-7 J-ST-00 User Spec. MIL-ST-0 Method 0 JES- JIS--69.Temperature: 85±5.Time:96 Hours.Humidity: 85±5% RH..Temperature: 05.Time:96 hours..pply rated current. Inspect product MIL-ST-88 Method 009 constructions, marking and workmanship. JES Method J-00 MIL-ST-0 Method 5 MIL-ST-0 Method 0 MIL-ST-0 Method 0 MIL-ST-0 Method 0.Temperature: 05.Time:96 hours..temperature: -0 ~ 05.Number of cycle:96 cycle.well time:0 minutes Verify physical dimensions to the applicable product detail specification. Immerse into solvent for ± minutes & brush 0 times for therr cycles..frequency and mplitued : Hz,.5 mm..irection:x, Y, Z.Test duration: hours for each direction, 6 hours in total..highest temperature: ±5.Time(temp. 7 ):60~ Second..IR reflow times: times..no mechanical and electrical pply rated current for 5 second..inductance shall not change more than ±%..No mechanical and electrical pply rated current for 0 minutes..inductance shall not change more than ±%..No mechanical and electrical pply twice as rated current for 5 minutes. (It's not application to some special design).inductance shall not change more than ±%..aking in pre-testing: 55±5 / 6Hours±0 min..peak temperature:0±5.time(temp. 7 ):60~ second..ir reflow times: times..operating temperature: -0 ~05.Room temperature:5..v:0v.time:minutes Test ondition Packaged & rop down from m.in angle ridges & surfaces orientation..pply push force to samples mounted on P..Force of.8 kg for 60± seconds. Test Specification.No mechanical and electrical.inductance shall not change more than ±%..No mechanical and electrical.inductance shall not change more than ±%..No mechanical and electrical.inductance shall not change more than ±%..No mechanical and electrical.inductance shall not change more than ±%..No pollution on the surface of products..lear marking..no crack. Per product specification standard.no body change in apperarance..no marking blurred..inductance shall not change more than ±%..No mechanical and electrical.inductance shall not change more than ±%..No mechanical and electrical.inductance shall not change more than ±%. The terminal shall be at least 95% covered with fresh solder..no mechanical and electrical.inductance shall not change more than ±%..uring the test no breakdown..the characteristic is normal after test..no case deformation or change in appearance..inductance shall not change more than ±%. fter test, inductors shall be no mechanical R-00