WLPM Series SMD Molded Power Inductors

Transcription

1 WLPM25212 Series SMD Molded Power Inductors *Contents in this sheet are subject to change without prior notice. Page 1 of 1 ASC_WLPM25212 Series_V4. Jun. 217

2 Features 1. Shielded construction. 2. Ultra low buzz noise. 3. Low DCR/µH. 4. Handles high transient current spikes without saturation. 5. Encapsulated body offers improved environmental protection and moisture resistance. 6. Higher dielectric withstanding voltage. 7. Corrosion resistant package. 8. RoHS Compliance. Applications 1. PDA/Notebook/Desktop/Server applications high current and low profile power supplier. 2. High current POL converters. 3. Battery powered devices. Shape and Dimension Code Dimensions(mm) L 2.5 ±.2 W 2. ±.2 T 1.2 MAX. e.5 ±.3 Recommend Pattern (Unit: mm) Page 2 of 1 ASC_WLPM25212 Series_V4. Jun. 217

3 Ordering Information WL PM M R33 P B Product Code Series Dimensions Thickness Tolerance Value Packing Code WL: Inductor SMD molded power inductor. 2.5 * 2.mm 1.2mm M: ± 2% R33=.33uH 2R2=2.2uH P=7 Reeled (Embossed tape) B:STD Electrical Characteristics WLPM25212 series Walsin Part Number L(uH) Tolerance Measuring Frequency (MHz),1V RDC Maximum (Ω) Rated Current (ma) (MAX.) (MAX.) Idc 1 Idc 2 WLPM25212MR47PB.47 M WLPM25212MR68PB.68 M WLPM25212M1RPB 1. M WLPM25212M1R5PB 1.5 M WLPM25212M2R2PB 2.2 M WLPM25212M3R3PB 3.3 M WLPM25212M4R7PB 4.7 M Maximum rated voltage: DC25V *)The saturation current value (Idc1) is the maximum DC current value having inductance decrease down to 3% (at 2 deg C) *)The temperature rise current value (Idc2) is the maximum DC current value having temperature increase up to 4degC. (at 2 deg C) *)The rated current is following either Idc1 or Idc2. which is the lower one. Caution for Temperature Rise. Temperature rise of this inductor depends on the installed board condition. It shall be confirmed in the actual end product that. temperature rise of inductor is within operating temperature. Operating temperature:-4 ~15 Storage temperature:-4 ~+85 Page 3 of 1 ASC_WLPM25212 Series_V4. Jun. 217

4 Electrical Properties DC Current Characteristics L VS Frequency Current Characteristics Inductance(µH) CSCA252D-R68M WLPM25212MR68PB DC DC Current Characteristics Temp. Rise T( ) Inductance(uH) WLPM25212MR68PB CSCA252D-R68M L VS FREQUENCE L VS Frequency ΔT( ) IDC(A) Frequency(MHz) Inductance(µH) Temp. Rise T( ) CSCA252D-1RM WLPM25212M1RPB DC DC Current Characteristics IDC(A) ΔT( ) Inductance(uH) WLPM25212M1RPB CSCA252D-1RM L VS L VS FREQUENCE Frequency Frequency(MHz) Inductance(µH) Temp. Rise T( ) WLPM25212M2R2PB CSCA252D-2R2M DC Current Characteristics IDC(A) ΔT( ) Inductance(uH) WLPM25212M2R2PB CSCA252D-2R2M L VS L VS FREQUENCE Frequency Frequency(MHz) Page 4 of 1 ASC_WLPM25212 Series_V4. Jun. 217

5 Reliability Testing Test Item Standard Test method Resistance to flexure substrate No damage. The test samples shall be soldered to the testing board and by reflow soldering conditions as show in page5 (Reflow profile chart). Apply pressure in the direction of the arrow until bent width reaches 2 mm. MECHANICAL CHARACTERISTICS Adhesion of Terminal electrode. Substrate size:1*4*1. Substrate material:glass epoxy-resin Solder cream thickness :.12 (Land size refer to recommended Land Pattern Dimensions of Precaution:) The test samples shall be soldered to the testing board and by reflow soldering conditions as shown page5 (Reflow profile chart). 1 N, 5 s Applied force:1 N to X and Y directions Duration:5 s. Solder cream thickness:.12mm (Land size refer to recommended Land pattern defined in Precaution ) Body strength No damage. Applied force :1 N Duration :1 s Page 5 of 1 ASC_WLPM25212 Series_V4. Jun. 217

6 Resistance to vibration Resistance to Soldering Solderability Temperature characteristics Thermal shock Low temperature life test observed in appearance. At least 9% of surface of terminal electrode is covered by new solder. Within±15%. The test samples shall be soldered to testing jig as shown in under table. Frequency range 1~55Hz 1.5mm(Shall not exceed acceleration Overall Amplitude 196 m/s 2 ) Sweeping Method 1 to 55 to 1 Hz for 1 min. 2 hours each in X,Y, and Z direction. 3 time of reflow oven at 23 degc min for 4 sec max. with peak temperature at 26+/-5 degc for 5 sec max. Substrate thickness. 1.mm Substrate material:glass epoxy-resin The test samples shall be submerged molten solder as shown in under table. Flux: methanol solution with 25% of rosin or equivalent. { Pb free solder: Sn-3Ag-.5Cu} Solder Temperature 245±5 deg C Immersing Speed {Eutectic solder} Solder Temperature Immersing Speed 5±.5s. 25 mm/s 23±5 deg C 5±.5s. 25 mm/s Measurement shall be taken in a temperature range of -4 degc to +85 degc and the value at +2 degc was used as the standard value. The test samples shall be soldered to the testing jig and by reflow soldering conditions as shown in page5 (Reflow profile chart). The test samples shall be left for the specified time at each of temperature in steps from 1 to 4, as shown in under table in sequence. The temperature cycles shall be repeated 1 cycled in the Method. Conditions for 1 cycle. Step Temperature (min) 1-4±3 deg C 3±3 2 Room Temp Within ±2 deg C 3±3 4 Room Temp Within 3 The test samples shall be soldered to the testing jig and by reflow soldering conditions as shown in page5 (Reflow profile chart). And after that proceed the test as shown condition under table. Temperature -4±2 deg C 1+24 h Page 6 of 1 ASC_WLPM25212 Series_V4. Jun. 217

7 Hihg temperature life test The test samples shall be soldered to the testing jig and by reflow soldering conditions as shown in page5 (Reflow profile chart). And after that proceed the test as shown condition under table. Temperature -4±2 deg C 5+24h ENVIRONMENT TESTS Damp heat life test Loading under damp heat life test The test samples shall be soldered to the testing jig and by reflow soldering conditions as shown in page5 (Reflow profile chart). The test samples shall be put in thermostatic oven set at temperature with humidity as shown in under table. Temperature Humidity 6±2 deg C 9~95%RH 5+24 h The test samples shall be soldered to the testing jig and by reflow soldering conditions as shown in page5 (Reflow profile chart). The test samples shall be put in thermostatic oven set at temperature with humidity, as shown in under table and with the rated current continuously applied. Temperature 6±2 deg C Humidity 9~95%RH Applied current Refer to Page h Standard measuring condition Unless otherwise specified, at least 2 hrs of recovery under the room temperature and normal humidity after the test. followed by the measurement within 48 hrs Page 7 of 1 ASC_WLPM25212 Series_V4. Jun. 217

8 Reflow Profile Chart (Reference): *Temperature on surface of circuit board 2.2 The products may be exposed to reflow soldering process of above profile up to two times. Page 8 of 1 ASC_WLPM25212 Series_V4. Jun. 217

9 Tape & Reel Packaging Dimensions Dimensions A B W F E P1 P2 P D T K Φ ±.1 ±.2 ±.5 ±.1 ±.1 ±.5 ±.1 ± ± max Direction of rolling Page 9 of 1 ASC_WLPM25212 Series_V4. Jun. 217

10 Reel Top tape strength Peel-off strength:.1n~1.2n Peel-off angle:165 ~18 Peel-off speed: 3mm/min Quantity per reel:3k pcs Page 1 of 1 ASC_WLPM25212 Series_V4. Jun. 217