POE INTERNATIONAL CORPORATION. SPECIFICATION OF MULTI-LAYER RADIAL-LEADED TYPE CAPACITOR Ver: 8 Page: 1

Transcription

1 SPECIFICATION OF MULTI-LAYER RADIAL-LEADED TYPE CAPACITOR Ver: 8 Page:. Scope: Its specification applies to Radial Series Ceramic Capacitor. 2.How to order: CODE: U RD2 R 02 K T Rated Voltage Code:U = 50 VDC, A = 00 VDC Size Code : refer to 3 Dielectric Code:C = NPO, R = X7R, F = Y5V Capacitance Code:02 = 000 pf (Two significant digits followed by no. of zeros) Tolerance Code:J = ±5%, K = ±0%, M = ±20%, Z = +80%/-20% (NPO: all tolerance, X7R: K M, Y5V: M Z) Package Code:T = Taping, B = Bulk 3. Lead configuration and size: (Lead material: Copper wire leads with Tin coating) Size Width Height Thickness Code (W) max. (H) max. (T) max. Length (L) RD " (5.5) 0.26" (5.5) 0.57" (4.0) 0.28"±0.003" (7.0±) RD2 0.26" (5.5) 0.26" (5.5) 0.57" (4.0) 0.28"±0.003" (7.0±) Unit: inch (mm) Lead spacing (F) 0.00"±0.030" (2.54±.0) 0.200"±0.030" (5.08±.0)

2 SPECIFICATION OF MULTI-LAYER RADIAL-LEADED TYPE CAPACITOR Ver: 8 Page: 2 4. Product structure: Chip capacitor Radial capacitor (6) Epoxy coating Chip capacitor (7) Radial lead NO Specifications Material Ceramic dielectric Ceramic 2 Internal Electrode Ag-Pd or Ni (BME) 3 Ag or Cu (BME) layer 4 End Termination Ni layer 5 Sn-Pb layer or Sn layer 6 Coating Expoxy 7 Radial Lead Wire Tined Copper wire 5. Test conditions: Tests shall, unless otherwise specified, be carried out at 5 to 35 and RH 45 to 75%. If any doubt and argument has been encounter in judgement, the final test shall be done at 25±2, RH45 to 55% and 860~060mbar. (Based on JIS standard) 6. Handle procedure: To avoid unexpected testing results from occurring, the tested capacitor must be kept at room temperature for at least 30 minutes and completely discharged.

3 SPECIFICATION OF MULTI-LAYER RADIAL-LEADED TYPE CAPACITOR Ver: 8 Page: 3 7.Identification of termination lead-plated and lead-free plated product There a mark P follow the lot number of Lead-free product for identification Ex: The lot number of Termination Lead product is: R3JBXXXX The lot number of Termination Lead-free product is: R3JBXXXX P 8. Test items: No. Item Performance Test or inspection method () Appearance No defects which may affect As section 8 structure size performance. (2) Withstand Voltage (3) Insulation resistance Withstand test voltage without Insulation breakdown or other damage. DC Tested voltage shall be applied for ~5sec. Charge/discharge current shall not exceed 50 ma. Rated Voltage Tested Voltage <00V 2.5Ra 00V 3.0Ra 200~300V 2.0 Ra 500~999V.5 Ra 000~3000V.2 Ra NPO: Insulation resistance shall be 0,000MΩ Min. or 500Ω*F Min measured at 20±5 seconds after X7R Y5V: 0GΩ Min or rated voltage applied. R C 500Ω.F Rated Voltage Tested Voltage (Whichever is smaller) <500V.0 Ra 500V 500V (4) Capacitance Within the specified tolerance. (5) Dissipation Factor More than 30pF Q 000 NPO Less than 30pF Q C 2.5% 50V (Except Cap 0.047uF,DF 3.0%) 3.5% 25V (Except Cap uf, DF 5.0%) X7R 6V(Except Cap uf DF 5.0%) 5.0% 0V 7.5% 6.3V 50V 5% 25V (Except Cap 0.uF; DF 7%) 6V (Cap < uf) Y5V 7% (Except Cap uf, DF 9%) 9% 6V (Cap uf) 2.5% 0V Measuring frequency & voltage: NPO:>000pF: KHz±0%.0±0.2 Vrms 000pF: MHz±0%.0±0.2 Vrms X7R Y5V: C 0uF.0±0.2 Vrms KHz±0% C>0 uf 0.5±0.2 Vrms 20Hz±20%

4 SPECIFICATION OF MULTI-LAYER RADIAL-LEADED TYPE CAPACITOR Ver: 8 Page: 4 No. Item Performance Test or inspection method The temperature coefficient is (6) Temperature Temperatures Coefficient determined using the capacitance Characteristic measured at base temperature as Operating Capacitance a reference. Test the specimen in of T.C. a range of maximum and Temperature Change(ΔC) minimum operation temperature Capacitance that shown as left table. NPO -55~+25 0±30(ppm/ ) * Base Temp 25±2 * Base Temp for Y5V: 20±2 (7) Terminal strength (8) Soldering heat resistance X7R Y5V -55~+25-25~+85 Tensile strength: No breakdown Bending strength: No breakdown External No mechanical damage. appearance Cap. change (ΔC/C) D.F. NPO X7R Y5V ± 5% +30%~-80% ±2.5% or ± 0.25 pf max. Whichever is larger ±7.5% ±20% To meet initial standard value Step Temperature( ) Base Temp.(25 )±2 2 Min. Operation Temp.±2 3 Base Temp.(25 )±2 4 Max. Operation Temp.±2 5 Base Temp.(25 )±2 Loading weight 0.5 Kgs is applied for 0± seconds Loading weight 0.25 Kgs is applied Bending back and forth 90 degrees twice Lead wire or terminals shall be immersed (A) up to 2.0 mm from body (B) into the Molten solder of which temperature is 270±5 for 0±3 sec. Then leave at standard test conditions for 24±2 hours, then measured. To meet initial standard value *Preconditioning: (only for Class 2): Perform a heat treatment at 50 +0/-0 for one hour and then let sit for 48 ± 4 hours at room temperature. I.R.

5 SPECIFICATION OF MULTI-LAYER RADIAL-LEADED TYPE CAPACITOR Ver: 8 Page: 5 No. Item Performance Test or inspection method (9) Solderability Lead wire shall be soldered over 75% of the circumfluent direction. (0) Humidity (Steady state) External appearance Cap. change (ΔC/C) D.F. No mechanical damage. NPO: ± 5% or ±0.5 pfmax. (Whichever is larger) X7R: ±2.5 % Y5V: ±30% NPO: C 30pF: D.F pF C<30pF: D.F. C<0pF: D.F C C PS: C: Nominal Capacitance (pf) X7R: 3.0% Rated voltage: 50V [Except Cap 0.047μF, DF 6%] 5.0% Rated voltage:25v [Except Cap μf, DF 0%] 5.0% Rated voltage:6v [Except Cap 0.033μF, DF 0%] 7.5% Rated voltage:0v [Except Cap 0.056μF, DF 5%] 5% Rated voltage:6.3 To comply with JIS-C , the soldering temperature is 235±5 and dipping time is 2±0.5 seconds. Flux: weight ratio of Rosin 25% Humidity (Steady state): At temperature 40±2 and humidity 90 to 95%RH for /-0 hours. Leave the capacitors in ambient condition for the following time before measurement. Class :24±2 hours. Class 2:48±4 hours. * Charge / discharge current shall. not exceed 50 ma. * Preconditioning: (only for Class 2): Apply the rated DC voltage for hour at 50 ±5. Remove and let sit for 48±4 hours at room temperature. Perform initial measurement. I.R. Y5V: 7.5% Rated voltage: 50V 7.5% Rated voltage:25v [Except Cap 0.μF,DF 0%] 0% Rated voltage:6v (C<.0μF) [Except Cap 0.068μF, DF 2.5%] 2.5% Rated voltage:6v (C.0μF) 5% Rated voltage: 0V GΩ min. or 50Ω*F (Whichever is smaller)

6 SPECIFICATION OF MULTI-LAYER RADIAL-LEADED TYPE CAPACITOR Ver: 8 Page: 6 No. Item Performance Test or inspection method () Humidity load External appearance Cap. change (ΔC/C) D.F. No mechanical damage. NPO: ± 5% or ±0.5 pfmax. (Whichever is larger) X7R: ±2.5 % Y5V: ±30% NPO: C 30pF: D.F. 200 C<30pF: D.F / 3 C PS: C: Nominal Capacitance (pf) X7R: 3.0% Rated voltage: 50V [Except Cap 0.047μF DF 6%] 5.0% Rated voltage:25v [Except Cap μf, DF 0%] 5.0% Rated voltage:6v [Except Cap 0.033μF, DF 0%] 7.5% Rated voltage:0v [Except Cap 0.056μF, DF 5%] 5% Rated voltage:6.3 Humidity load: ( apply for the product with rated voltage 500V-Max): Apply the rated voltage at temperature 40±2 and humidity 90 to 95%RH for /-0 hours. Leave the capacitors in ambient condition for the following time before measurement. Class :24±2 hours. Class 2:48±4 hours. * Charge / discharge current shall. not exceed 50 ma. * Preconditioning:(only for Class 2): Apply the rated DC voltage for hour at 50 ±5. Remove and let sit for 48±4 hours at room temperature. Perform initial measurement. I.R. Y5V: 7.5% Rated voltage: 50V 7.5% Rated voltage:25v [Except Cap 0.μF DF 0%] 0% Rated voltage:6v (C<.0μF) [Except Cap 0.068μF,DF 2.5%] 2.5% Rated voltage:6v (C.0μF) 5% Rated voltage: 0V 500MΩ min. or 25Ω*F (Whichever is smaller)

7 SPECIFICATION OF MULTI-LAYER RADIAL-LEADED TYPE CAPACITOR Ver: 8 Page: 7 No. Item Performance Test or inspection method (2) Load Life External appearance Cap. change (ΔC/C) No mechanical damage. NPO: ±3% or ±0.3pFmax. (Whichever is larger) X7R: ±2.5 % Rated Voltage Tested Voltage < 500V 2.0Ra 500V < 000V.5Ra 000V.2Ra D.F. I.R. Y5V: ±30% NPO: C 30pF: D.F pF>C 0pF: D.F C C<0pF:D.F C PS: C: Nominal Capacitance (pf) X7R: 3.0% Rated voltage: 50V Apply 200% of the rated DC voltage [Except Cap 0.047μF, DF 6%] for hour at the maximum operating 5.0% Rated voltage:25v [Except Cap μf, DF 0%] temperature ± 3. Remove and let 5.0% Rated voltage:6v sit for 48±4 hours at room [Except Cap 0.033μF,DF 0%] 7.5% Rated voltage:0v temperature. Perform initial [Except Cap 0.056μF, DF 5% measurement. 5% Rated voltage:6.3 Y5V: 7.5% Rated voltage: 50V 7.5% Rated voltage:25v [Except Cap 0.μF,DF 0%] 0% Rated voltage:6v (C<.0μF) [Except Cap 0.068μF,DF 2.5%] 2.5% Rated voltage:6v (C.0μF) 5% Rated voltage: 0V 000MΩ min. or 50Ω*F (Whichever is smaller) at maximum operating temperature ±2 for /-0 hours. Leave the capacitors in ambient condition for the following time before measurement. Class I: 24±2 hours Class II: 48±4 hours * Charge / discharge current shall. not exceed 50 ma. * Preconditioning:(only for Class 2):

8 SPECIFICATION OF MULTI-LAYER RADIAL-LEADED TYPE CAPACITOR Ver: 8 Page: 8 No. Item Performance Test or inspection method External (3) Temperature No mechanical damage. appearance cycle Cap. change (ΔC/C) D.F. I.R. 9. Storing condition and term: NPO: ±2.5% or ±0.25pFmax. ( Whichever is larger) X7R: ±7.5 % Y5V: ±20 % To meet initial standard value 0000MΩ min. or 500Ω*F (Whichever is smaller) The capacitor shall be subject 5 cycles according to four heat treatments listed in the following table. Then Leave the capacitors in ambient condition for the following time before measurement. Class I: 24±2 hours Class II: 48±4 hours Step Duration Temperature ( ) (min.) Min. Operation Temp.±3 30±3 2 Room Temp. (25 ) 2 ~ 3 3 Max. Operation Temp.±3 30±2 4 Room Temp. (25 ) 2 ~ 3 *Preconditioning:(only for Class 2): Perform a heat treatment at for one hour and then let sit for 48±4 hours at room Recommends the storing of products within 6 months at temperature 5 ~ 40 and humidity 20~70% RH max. 0.Description: Pan Overseas Radial-Leaded, Epoxy-Dipped Multilayer ceramic capacitors are built by superior moisture and shock resistant Epoxy coating, can be supplied in both bulk or tape and reel package for automatic insertion in printed circuit board. Our RD series capacitors have wide application in computer, data Processor, telecom communication, industrial control, and instrumentation equipment, etc. (Epoxy coated: Flame resistance for UL94 V-0 Approved). Features: () Enhanced environmental protection coating. (2) COG (NPO) X7R Y5V characteristic. (3) Variety of Lead configuration.

9 SPECIFICATION OF MULTI-LAYER RADIAL-LEADED TYPE CAPACITOR Ver: 8 Page: 9 2. Taping specification: (RD2) Description Symbol Dimension Remarks Pitch Of Component P 2.7±0. Feed Hold Pitch P0 2.7±0.3 Feed Hold Center to Lead P 3.85±0.7 Feed Hold Center to Component Center Lead To Lead Spacing Component Alignment, F-R P2 6.35±.3 F Δh 5.0 ±0.8 or 2.5 ± Max Tape Width W /-0.5 Adhesive Tape Width W0.0 Min. Hole Position W 9.0±0.5 Adhesive Tape Position W2 3.0 max. Height Of Bottom Body From Tape Center Lead-Wire Clinch Height Unit: mm Cumulative Pitch Error: ±.0 Mm/20 Pitches To Lead Tip Within Tolerance The Alignment From The Center Of The Lead Is±.0mm H /-0 H+2.5mm H H0 6.0±0.5 or 8.0±0.5 Component Height H Max. Feed Hole Diameter D0 4.0±0.3 Tape Thickness t 0.7± H0-W

10 SPECIFICATION OF MULTI-LAYER RADIAL-LEADED TYPE CAPACITOR Ver: 8 Page: 0 3. Taping specification: (RD20) Description Symbol Dimension Remarks Pitch Of Component P 2.7±0. Feed Hold Pitch P0 2.7±0.3 Feed Hold Center to Lead P 3.85±0.7 Feed Hold Center to Component Center P2 6.35±.3 Lead To Lead Spacing F 5.0 ±0.8 or 2.5 ±0.8 Component Alignment, F-R Δh 2.0 Max Tape Width W /-0.5 Adhesive Tape Width W0.0 Min. Hole Position W 9.0±0.5 Adhesive Tape Position W2 3.0 max. Height Of Bottom Body From Tape Center Lead-Wire Clinch Height Unit: mm Cumulative Pitch Error: ±.0 Mm/20 Pitches To Lead Tip Within Tolerance The Alignment From The Center Of The Lead Is±.0mm H /-0 H+2.5mm H H0 6.0±0.5 or 8.0±0.5 Component Height H Max. Feed Hole Diameter D0 4.0±0.3 Tape Thickness t 0.7± Packing quantity: Size code Taping type 6.5 H0-W Bulk type Quantity per reel Quantity per box Qunatity per bag RD20, RD2 3,000 2,000,000

11 SPECIFICATION OF MULTI-LAYER RADIAL-LEADED TYPE CAPACITOR Ver: 8 Page: 5. Size code and capacitance (pf) available: 0603 Size Code Rated Voltage COG(NPO) X7R Y5V RD20,RD2 0VDC VDC VDC VDC ~ ~ , VDC 00~ ~ VDC 00~ Size Code Rated Voltage COG(NPO) X7R Y5V RD20,RD2 0VDC VDC VDC VDC 200~ ~ , VDC 000~ ~ VDC 820~ ~ VDC 0~470 00~ VDC 0~270 47~ Size Code Rated Voltage COG(NPO) X7R Y5V RD20,RD2 0VDC VDC VDC VDC 3900~ ~ VDC 3900~ ~ VDC 3300~ ~ VDC 0~000 00~ VDC 0~270 47~

12 SPECIFICATION OF MULTI-LAYER RADIAL-LEADED TYPE CAPACITOR Ver: 8 Page: 2 Size code and capacitance (pf) available: 20 Size Code Rated Voltage COG(NPO) X7R Y5V RD20,RD2 0VDC VDC VDC VDC 5000~ ~ VDC 5000~ , VDC 0000, ~ VDC 0~ ~ VDC 0~500 00~ Size Code Rated Voltage COG(NPO) X7R Y5V RD20,RD2 0VDC VDC VDC VDC 47000~ ~ VDC 47000~ , VDC 22000~ ~ VDC 0~ ~ VDC 0~ ~

13 SPECIFICATION OF MULTI-LAYER RADIAL-LEADED TYPE CAPACITOR Ver: 8 Page: 3

14 SPECIFICATION OF MULTI-LAYER RADIAL-LEADED TYPE CAPACITOR Ver: 8 Page: 4

15 SPECIFICATION OF MULTI-LAYER RADIAL-LEADED TYPE CAPACITOR Ver: 8 Page: 5