AD Scope: Its specification applies to Radial Series Ceramic Capacitor. 2.How to order: CODE

Transcription

1 1 1. Scope: Its specification applies to Radial Series Ceramic Capacitor. 2.How to order: CODE U AD10 R 102 K T Rated Voltage CodeT = 25 VDC U = 50 VDC Size Code : refer to the description in 3 Dielectric CodeC = NPO, R = X7R, F = Y5V, E = Z5U Capacitance Code102 = 1000 pf (Two significant digits followed by no. of zeros) Tolerance CodeJ = 5%, K = 10%, M = 20%, Z = +80%/-20% ( all tolerance, X7R: KM, Z5U & Y5V: MZ) Package CodeT = Taping, B = Bulk 3. Lead configuration and size: (Lead material: Copper wire leads with Tin coating) Unit: mm Length Body diameter Wire diameter Size Code (L) max. (D) max. (d) AD10 AD20

2 2 4. Product structure: MLCC Chip capacitor Axial Lead Capacitor NO Specifications Material 1 Ceramic dielectric Ceramic 2 Internal Electrode Ag-Pd or Ni (BME) 3 Ag or Cu (BME) layer 4 End Termination Ni layer 5 Sn-Pb layer or Sn layer 6 Coating Expoxy 7 Axial Lead Wire Tined Copper wire

3 3 5. Test conditions: Tests shall, unless otherwise specified, be carried out at 15 to 35and RH 45 to 75%. If any doubt and argument has been encounter in judgement, the final test shall be done at 25±2, RH45 to 55% and mbar. (Based on JIS standard) 6. Handle procedure: To avoid unexpected testing results from occurring, the tested capacitor must be kept at room temperature for at least 30 minutes and completely discharged. 7. Test items: No. Item Performance Test or inspection method (1) Appearance structure size No defects which may affect performance. (2) Withstand Voltage Withstand test voltage without (3) Insulation resistance Insulation breakdown or other damage. 100,000MMin. or RC 0 F (Whichever is smaller) X7R, Y5V, Z5U: 10,000MMin or RC 1,000 F (Whichever is smaller) As section times of rated DC voltage shall be applied for 15sec. Charge/discharge current shall not exceed 50 ma. Insulation resistance shall be measured at 60 5 seconds after rated voltage applied. Rated voltage DC Tested voltage V V 1.0 Ra 500V (4) Capacitance Within the specified tolerance. Measuring frequency: Z5UY5VX7R1KHz 50Hz (5) Dissipation Factor NPO NPO 1000pF1KHz 50Hz 1000pF1MHz 100KHz 30pFQ Measuring voltage: < 30pF : Q Z5U0.5 Vrms PS: C: Nominal Capacitance (pf) NPOX7RY5V Vrms T.C. 50V 25V 16V 10V X7R2.5% 3.0% 3.5% 5.0% Z5U 4.0% Y5V 5.0% 7.5% 9.0% 12.5%

4 4 No. Item Performance Test or inspection method (6) Temperature Temperatures Coefficient The temperature coefficient is determined using the capacitance Characteristic Operating Capacitance measured in step 3 as a reference. T.C. of Temperature Change(C) Test the specimen from step 1 through step 5, the capacitance Capacitance shall be within the specified NPO -55~+125 0±30(ppm/) tolerance for the capacitance coefficient and capacitance X7R -55~+125 ± 15% change as left table. Y5V -25~+85 Temperature() 30%~80% (7) Terminal strength (8) Soldering heat resistance Z5U +10~+85 Tensile strength: No breakdown +22%~ -56% Bending strength: No breakdown External No mechanical damage. appearance Cap. change C/C) D.F. I.R. NPO X7R Z5U Y5V ±2.5% or ± 0.25 pf max.( Whichever is larger) ±7.5% ±20% ±20% C30pFQ1000 C30pFQ400+20*C PS: C: Nominal Capacitance (pf) (Max. value) T.C. 50V 25V 16V 10V X7R 2.5% 3.0% 3.5% 5.0% Z5U 4.0% Y5V 5.0% 7.5% 9.0% 12.5% 100,000MMin. or RC 0 F (Whichever is smaller) X7R, Y5V, Z5U: 10,000MMin or RC 1,000 F (Whichever is smaller) Loading weight 0.5 Kgs is applied for 10±1 seconds Loading weight 0.25 Kgs is applied Bending back and forth 90 degrees twice Lead wire or terminals shall be immersed (A) up to 2.0 mm from body (B) into the Molten solder of which temperature is 270±5 for 10±1 sec. Then leave at standard test conditions for 24±2 hours, then measured. Preconditioning(only for Class 2): Perform a heat treatment at ±

5 No. Item Performance Test or inspection method (9) Solderability Lead wire shall be soldered over 75% of the circumfluent direction. To comply with JIS-C , the soldering temperature is and dipping time is seconds. Flux: weight ratio of Rosin 25% (10) Humidity (Steady state) External No mechanical damage. appearance Cap. change C/C) D.F. ± 5% or ±0.5 pfmax. (Whichever is larger) X7R: 12.5 Y5V: ±30% Z5U: ±30% C30pF: Q 10pFC30pF: Q *C C10pF: *C PS: C: Nominal Capacitance (pf) X7R: Less than 2 times of initial value Y5V & Z5U: Less than 1.5 times of initial value Humidity (Steady state): At temperature 40±2 and humidity 90 to 95%RH for 50024/ 0 hours. Leave the capacitors in ambient condition for the following time before measurement. Class hours. Class hours. * Charge / discharge current shall. not exceed 50 ma. * Preconditioning (only for Class 2): Apply the rated DC voltage for 1hour at 150 ±5. Remove and let sit for 48±4 hours at room temperature. Perform initial measurement. I.R. 500M min. or 25*F (Whichever is smaller)

6 (11) Humidity load External appearance Cap. change C/C) D.F. I.R. No mechanical damage. ± 5% or ±0.5 pfmax. (Whichever is larger) X7R: 12.5 Y5V: ±30% Z5U: ±30% C30pF: Q 10pFC30pF: Q *C C10pF: *C PS: C: Nominal Capacitance (pf) X7R: Less than 2 times of initial value Y5V & Z5U: Less than 1.5 times of initial value 500M min. or 25*F (Whichever is smaller) Humidity load: ( apply for the product with rated voltage 500V-Max): Apply the rated voltage at temperature 40±2 and humidity 90 to 95%RH for 50024/ 0 hours. Leave the capacitors in ambient condition for the following time before measurement. Class hours. Class hours. * Charge / discharge current shall. not exceed 50 ma. * Preconditioning(only for Class 2): Apply the rated DC voltage for 1hour at 150 ±5. Remove and let sit for 48±4 hours at room temperature. Perform initial measurement. (12) Load Life External No mechanical damage. appearance Cap. change C/C) D.F. ±3% or ±0.3pFmax. (Whichever is larger) X7R: 12.5 Y5V: ±30% Z5U: ±30% Apply 2 ± Leave the capacitors in ambient condition for the following time before measurement. C30pF: Q350 30pF>C10pF: * Charge / discharge current shall. Q *C not exceed 50 ma. C10pFQ200+10*C PS: C: Nominal Capacitance (pf) * Preconditioning(only for Class 2): Apply 200% of the X7R: Less than 2 times of initial value ± Y5V & Z5U: Less than 1.5 times of initial value I.R. Whichever is smaller

7 7 (13) Temperature cycle External No mechanical damage. appearance Cap. change (C/C) D.F. ±2.5% or ±0.25pFmax. Whichever is larger) X7R: 7.5 Y5V: 20 C30pFQ1000 C30pFQ400+20*C X7RY5V&Z5U: (Max. value) T.C. 50V 25V 16V 10V X7R 2.5% 3.0% 3.5% 5.0% Z5U 4.0% Y5V 5.0% 7.5% 9.0% 12.5% The capacitor shall be subject 5 cycles according to four heat treatments listed in the following table. Then Leave the capacitors in ambient condition for the following time before measurement. Class II: 48 4 hours Duration Step (min.) 1 ± ± 2 3 ±± 4 I.R. 8. Storing condition and term: 10000Mmin. or 500*F (Whichever is smaller) *Preconditioning(only for Class 2): Perform a heat treatment at ± Recommends the storing of products within 6 months at temperature 5 ~ 40and humidity 20~70% RH max. 9. Description: Pan Overseas Axial-Leaded, Epoxy-coated Multilayer ceramic capacitors are coated with superior moisture and shock resistant coating, built by high volume, automatic process to ensure an uniform conformal coating. These capacitors are supplied in both bulk or tape and reel package for automatic insertion and sequencing with any axial leaded components. 10. Features: (1) Enhanced environmental protection coating. (2) 50V, 100V rated voltage. (3) COG (NPO)X7RY5VZ5U characteristic. (4) Bulk or tape / reel packing.

8 8 11. Taping specification: Unit: mm Item Symbol Dimension Item Symbol Dimension Pitch of component P Centered C Cumulative tolerance of pitch over 6 consecutive units 0.15 Core Diameter D (standard 61.0) Tape width Wt Real Diameter D2 360 max. Lead Wire Protrusion Le 1.57max. Core Width W Lead Extension into Tape Li 3.96max. Recess Depth R 9.5 min. Offset between tapes T 0.8max. Arbor Hole H0 Width between tapes W Deflection Form Nominal Position h (standard 15.9) 1.2 max. 12. Packing quantity: Size code Taping type Bulk type Quantity per reel Quantity per box Qunatity per bag AD10, AD20 5,000 5,000 1,000

9 13. Size code and capacitance (pf) available: 0603/0805 Size Rated Code Voltage AD10 COG(NPO) X7R Y5V Z5U 25 VDC , VDC 10 ~ 3, VDC 10 ~ 1, ~ 2,200, ~ 1,000, ,000 ~ 1,000,000 10,000 ~ 2,200, ,000 ~ 1,000,000 1,000 ~ 330, Size Code AD20 Rated Voltage 25 VDC VDC VDC --- COG(NPO) X7R Y5V Z5U 1,000,000 ~ 2,200, ,000 ~ 1,000, ,000 ~ 470,000 1,000,000 ~ 2,200,000 1,000, ,000 ~ 1,000,

10 10 Capacitance Specification Table (Class I) T.C NPO Size Rated Voltage Code pF pF pF uF 103

11 11 Capacitance Specification Table (Class II) T.C X7R Size Rated Voltage Code pF pF uF

12 12 Capacitance Specification Table (Class II) T.C Y5V Size Rated Voltage Code pF pF uF

13 13 T.C Z5U Size Rated Voltage Code pF uF Capacitance Specification Table (Class II)