SPECIFICATION. 1. Scope This specification applies ferrite Chip common mode filters C3-2012F-Series to be delivered to user.

Transcription

1 C C3-202F-Series. Scope This specification applies C3-202F-Series to be delivered to user. 2. Product Identification C3-202 F P - T () (2) (3) (4) (5) (6) () Product name (2) Shapes and dimensions (3) Shielding Type (4) Impedance at 00MHz 900:90Ω (5) Number of Line 2P:2-Line (6) Taping Type SPECIFICATION 3. Shapes and Dimensions [Dimensions in mm] A Epoxy B A : 2.0 ± 0.2 B :.2 ± 0.2 C :.2 ± 0.2 Terminations Wires 4 (0.4) Equivalent circuit (0.4) 2 No Polarity 3 (0.45) (0.45) 2/02/207 Copyright All rights reserved.

2 C3-202F-Series 4. Electrical Characterisitics 4- Electrical Spec. Common-Mode Insulation Withstand DC Resistance Rated Current Rated Voltage Our Product Part Number Impedance Resistance Voltage Rdc(Ω) Max. Idc(mA) Max. Vdc(V) Z(Ω) at 00MHz (MΩ)Min. Vdc(V) C3-202F-250-2P-T 25 ±25% C3-202F-300-2P-T 30 ±25% C3-202F-400-2P-T 40 ±25% C3-202F-420-2P-T 42 ±25% C3-202F-500-2P-T 50 ±25% C3-202F-670-2P-T 67 ±25% C3-202F-750-2P-T 75 ±25% C3-202F-900-2P-T 90 ±25% C3-202F-2-2P-T 20±25% C3-202F-6-2P-T 60±25% C3-202F-8-2P-T 80±25% C3-202F-20-2P-T 200±25% C3-202F-22-2P-T 220±25% C3-202F-26-2P-T 260±25% C3-202F-30-2P-T 300±25% C3-202F-33-2P-T 330±25% C3-202F-37-2P-T 370±25% C3-202F-60-2P-T 600±25% C3-202F-67-2P-T 670±25% C3-202F-68-2P-T 680±25% C3-202F-80-2P-T 800±25% C3-202F-90-2P-T 900±25% C3-202F-02-2P-T 000±25% C3-202F-222-2P-T 2200±25% /02/207 Copyright All rights reserved.

3 Impedance(OHM) Impedance(ohm) Impedance(Ω) Impedance(Ω) C3-202F-Series 4-2Characteristics(Reference) 000 C3-202F-300-2P-T 000 C3-202F-400-2P-T C3-202F-420-2P-T C3-202F-500-2P-T C3-202F-670-2P-T C3-202F P-T /02/207 Copyright All rights reserved.

4 Impedance(OHM) Impedance(OHM) Impedance (ohm) Impedance(ohm) Impedance(Ω) Impendance(OHM) C3-202F-Series C3-202F-900-2P-T C3-202F-2-2P-T Common mode Differential mode C3-202F-6-2P-T C3-202F-8-2P-T 000 Z (common mode) Z(differential mode) C3-202F-20-2P-T 0000 C3-202F-22-2P-T /02/207 Copyright All rights reserved.

5 Impedance(OHM) Impedance(OHM) Impedance(OHM) Impedance ( ohm) C3-202F-Series C3-202F-26-2P-T T q C3-202F-30-2P-T Z (common mode) Z(differential mode) C3-202F-33-2P-T C3-202F-37-2P-T C3-202F-67-2P-T 0000 C3-202F-60-2P-T Common mode Differential mode /02/207 Copyright All rights reserved.

6 Impedance( ohm) C3-202F-Series C3-202F-68-2P-T T q C3-202F-80-2P-T Z (common mode) Z(differential mode) C3-202F-90-2P-T C3-202F-02-2P-T C3-202F-222-2P-T 2/02/207 Copyright All rights reserved.

7 2/02/207 Copyright All rights reserved. C3-202F-Series 4-3 Test Equipment 4-3- Impedance Measured by using Agilent E499A RF Impedance Analyzer. Measurement terminal DC Resistance Measured by using Chroma 6502 mill ohm meter. Measurement terminal Measurement terminal Insulation Resistance Measured by using Chroma 9073 Measurement voltage : 50v. Measurement terminal 2 4 3

8 2/02/207 Copyright All rights reserved. C3-202F-Series 5.Reliability Test Operating temperature : -40 to +05 Specifications Item Solder ability Terminal Storage temp and humidity : 20~25,60%RH max. It can be connected on the Apply cream solder to the test circuit board. Recommendation soldering conditioit is mounted on the recommendation soldering condition. Dip pads in flux and dip in solder pot( 96.5 Sn/3.5 Ag solder) at 255 C ±5 C. Test conditions The terminal electrode and the ferrit Solder a chip to test substrate, and then laterally apply a strength must not be damaged. load 0.5Kg in the arrow direction. Strength on The terminal electrode and the ferrit Soldering a chip to a test substrate, pc board must not be damaged. bend the substrate by 2mm and then return. bending Width side length Force Dimensions in mm R0 Test board : Glass base epoxy multiplayer board pc board pattern. PC board pattern : Recommended PC board pattern.

9 C3-202F-Series Item High temperature resistance Appearance : Ferrite shall not be damaged. Temperature : +05±2 Applied voltage : Rated voltage Applied current : Rated current initial value. Testing time : 500±2 hours insulation resistance: >0(MΩ) Measurement : After placing for 24 hours min. DC resistance : standard value Humidity inside. Temperature : +85±2 resistance Specifications Test conditions Humidity : 90 to 95%RH Applied current : Rated current Applied voltage : Rated voltage Testing time : 500±2 hours Measurement : After placing for 24 hours min. Thermal Temperature : -40,+05 cycle kept stabilized for 30 minutes each. Cycle : 00 cycle Measurement : After placing for 24 hours min. cycle min. 3 min min. Low Temperature : -40±2 temperature resistance Testing time : 500±2 hours Measurement : After placing for 24 hours min. Vibration Appearance : Ferrite shall not be Frequency : 0 to 50 Hz damaged. Amplitude :.52 mm Dimension and times : X,Y and Z directions for 2 hours each. 2/02/207 Copyright All rights reserved.

10 2/02/207 Copyright All rights reserved. C3-202F-Series 6.Packaging The packaging must be done not to receive any damage during transporting and storing P P 0 P Ko W Bo t Ao ( Dimensions in mm; Tolerance:±0.) Symbol W P P 0 P Ao Bo Ko t Dimension Reel dimensions D C B A ( Dimensions in mm ) Symbol T A 80 B 60 C 3 D 4.4 E 8.4 E 6-3 Tapping figure Top cover tape Carrier tape Sprocket hole Cavity (chip insert)

11 C3-202F-Series 6-4 Packaging Form There shall not continuation more than two vacancies of the product. (360 mm) Blank Chip Blank Leader. 50 pitches 70 pitches Material of carrier tape : Polystyrene Material of cover tape : Polyester 6-5 Cover Tape Peel Strength The force for tearing off cover tape is 0.~0.69(N) in the arrow direction at the following conditions: Temperature : 5 ~ 35 Humidity : 45 ~ 85% Atmospheric pressure : 860 ~ 060 hpa 60 ~ 80 Top cover tape Base tape 6-6 Packing Quantity φ80 mm reel T type : 2000 pcs./reel 7. Recommended Soldering Conditions (Please use this product by reflow soldering) 7- Recommended Footprint Termination Number : Please refer to the equivalent circuit in chapter Unit:mm 2/02/207 Copyright All rights reserved.

12 2/02/207 Copyright All rights reserved. C3-202F-Series 7-2 Recommended Reflow Pattern Reflow : until two times 0sec. Min Natural cooling 50 50sec Max.. 60sec. Min. 7-3 Iron Soldering Use a solder iron of less than 30W when soldering,do not allow the soldering iron tip directly touch the ferrite body outside of terminal electrode. 5 seconds max. at Attention in Case of Using 9. Others In case of using product,please avoid following matters: Splashing water or salt water Dew condenses Toxic gas (Hydrogen sulfide, Sulfurous acid,chlorine, Ammonia) Vibrations or shocks which exceed the specified condition Please be careful for the stress to this product by board flexure or something after the mounting. 9- Operating temperature range : -40~ Storage condition : Temperature 20~25, Relative Humidity 40% ~ 60% 9-3 Recommended wire wound inductors should be used within 6 months from the time of delivery.