Chip Type Y5U Temperature Characteristics

Transcription

1 Chip Type Y5U Temperature Characteristics Features Dimensions Large capacitance in small size Temperature characteristics of Y5U (within +% to 56% in the range of 5 C to +85 C) Features equivalent to X7V. Reel packaging at customer request (8 and mm carrier tapes are available) Available in silver electrode type and solder plated electrode type. All capacitors of this type designed for use in reflow soldering. Case code Q W L W T L Unit: mm Q (min.) 3.±..6±. 3.± ± ±.7± 4.5±.4 3.± ±.4 5.±.4 Standard Products Line-up and Outer Dimension T R.V. (V) A(V) Case Code C (µf) C (6V) E (5V) H (5V) A (V) : Silver electrode type : Plated type Unit: mm max. 3. Multilayer Ceramic Capacitors Vol.

2 Specifications Item Operating Temperature Rated Voltage Dimensions Capacitance Tolerance Insulation Resistance Withstanding Voltage Capacitance change owing to temperature ( 5 C to +85 C) Adhesion Specification 5 C to +5 C 6, 5, 5, VDC Refer to dimensions and standard products list Between +8 and % Less than (Y5UA type: 5max.) More than 5 ΩF No insulation destruction or breakage should exist Between + and 56% (no applied voltage) Test Conditions (JIS C 5, 994) 5 C:.7 wv max, 5 C:.5 wv max. Refer to paragraph 6. Measure the dimension of the capacitor using vernier calipers of more than second grade defined in JIS B 757. Refer to paragraphs 7.8 and 7.9 Frequency for measurement: khz ±% Time for applying voltage: ±. V.rms Refer to paragraph 7.6 Applied voltage: Rated voltage Application time: 6±5 sec. Refer to paragraph 7. Applied voltage: Rated voltage Application time: to 5 sec. Charging and discharging currents: Less than 5 ma Refer to paragraph 7. Preprocessing: + C and C After having been subjected to heat treatment for one hour, the capacitor is left for 4± hrs. at room temperature Test of an aluminum substrate shown below The substrate is soldered to a jig using solder containing a mixture of - 3. wt.% silver, and a force of 5N (.5 kg f) in the direction designated by the arrow. The substrate is retained for ± sec. Substrate for test purposes Direction of application of force (5N) Capacitor C/C Within ±% In compliance with an appendix of JIS C 649 Press the center of the substrate at a rate of about mm/sec. until the amount of deflection becomes mm, and the substrate is retained for 5 sec. while remaining in that state Bond strength of Face Plating Press Bar Capacitor Pressure 45± 45± Support Table Test table Solderability Resistance to Soldering Heat C/C Within ±% Withstanding Voltage More than 75% of each terminal electrode covered with new solder Less than initially specified value More than initially specified value C/C Within ±% Initial spec Less than initially specified value Refer to paragraph 8.4 Solder: Including a mixture of to 3. wt.% Ag Solder temperature: 35±5 C Dipping time: ±.5 sec. Dipping rate: 5± mm/sec. Refer to paragraph 8.5 Solder: Including a mixture of to 3. wt.% Ag Preprocessing: Between + C and C, hr. Preheating: Between + C and C, - min. Solder temperature: 6±5 C Dipping time: 5±.5 sec. Dipping rate: 5± mm Refer to paragraph 9.3 Preprocessing: Between + C and C, hr. Number of cycles: 5 Temperature Cycle Withstanding Voltage More than initially specified value Initial spec Level 3 4 5± Ambient temperature +85± Ambient temperature Time (min.) 3±3 ~5 3±3 ~5 Humidity Resistance C/C Within ±% Less than initially specified value No abnormality Refer to paragraph 9.9 Temperature: 4± C Relative humidity: 9-95% RH Applied voltage: Rated voltage Time: Between 5 +4 and 5 hrs. Multilayer Ceramic Capacitors Vol. 3

3 High-temperature Load (I) High-temperature Load (II) C/C Within ±3% Less than initially specified value No abnormality C/C Within ±3% Less than initially specified value No abnormality Refer to paragraph 9. Temperature: 85± C Applied voltage: Rated voltage Time: between +48 and hrs. Preprocessing: 85 C and hr has been applied to the capacitor, the capacitor is left for 4±hr at ambient temperature Refer to paragraph 9. Temperature: 5± C Applied voltage: Half the rated voltage Time: between +48 and hrs. Preprocessing: 5 C and hr has been applied to the capacitor, the capacitor is left for 4±hr at ambient temperature Others Complies with Fixed Multilayer Magnetic Capacitor for Electronic Equipment JEITA RCR-5 Note: Capacitors here are designed for reflow soldering purposes. Standard Products Part Number Rated Voltage (VDC) Case Code Nominal Capacitance (µf) Thickness "T" (mm) max. Taping K (±.) Y5UA5ZP Y5UA685ZP Y5UA6ZP Y5UA6Z Y5UA6Z Y5UA6Z.7 Y5UA6Z Y5UA6Z.7 Y5UA6Z Y5UA6Z.7 Y5UA686Z Y5UA7Z.7 Y5UC5ZP Y5UC5ZP Y5UC5ZP Y5UC5ZP Y5UC5ZP Y5UC5ZP Y5UC5ZP Y5UC5ZP Y5UC5Z Y5UC685Z Y5UC6Z Y5UC5ZP Y5UC5ZP Y5UC685ZP Y5UC6ZP Y5UC6Z Y5UC6Z Y5UC6Z Y5UC5ZP Y5UC685ZP Y5UC6ZP Y5UC6Z Y5UC6Z Y5UC6Z Y5UC6Z Y5UC6Z Y5UE684ZP Y5UE5ZP Y5UE5ZP Y5UE5Z [ ] Y5UE5Z [ ] Y5UE5Z [ ] Y5UE5Z [ ] Y5UE685Z [ ] Y5UE6Z [ ] Y5UE5Z [ ] Y5UE685Z [ ] Y5UE6Z [ ] Y5UE6Z Y5UE6Z Y5UE6Z Y5UE36Z () (.6) () (.7) () (.7) () () () (.7) () () () (.7) () () (3.) 4 Multilayer Ceramic Capacitors Vol.

4 Part Number Y5UH5Z [ ] Y5UH5Z [ ] Y5UH5Z [ ] Y5UH5Z [ ] Y5UH5Z [ ] Y5UH5Z [ ] Y5UH5Z Y5UH685Z Y5UH6Z Y5UA4Z Y5UA4Z [ ] Y5UA4Z [ ] Y5UA4Z [ ] Y5UA684Z [ ] Y5UA5Z [ ] Y5UA5Z [ ] Y5UA4Z [ ] Y5UA4Z [ ] Y5UA684Z [ ] Y5UA5Z [ ] Y5UA5Z Y5UA5Z Y5UA5Z 5 Rated Voltage (VDC) Case Code Nominal Capacitance (µf) Thickness "T" (mm) max. Taping K (±.) () (.7).7 (.7) (.7) () () () () () ().6.7 (.6) (.7). 3.8 () () () () () () () 3. () () () () (.7) (.7) (.7).7.7 () () 3 () () () () () (.7) Please add "P" to plated electrode or no suffix to silver electrode for type of terminal electrode in square brackets. Dimensions in parentheses are for plated-electrode models. Note : Products of this type are designed for reflow soldering purposes. If taped chip capacitors are required,refer to page 9~3 when Test Data (Typical Examples) Temperature and DC bias characteristics of capacitance Y5UH5Z Y5UE6Z Y5UA5Z V V V 5 V 5 V 5 5 V V 5 5 V 5 V Impedance vs Frequency Characteristics Impedance (Ω) Y5UA4Z Y5UA5Z Y5UA5Z Y5UC6Z Y5UE6Z Y5UC6Z Y5UC6Z Y5UA7Z.. Frequency (khz) Multilayer Ceramic Capacitors Vol.

5 ordering. High-temperature Load Characteristics (85 C) 4 Y5UE6Z Applied voltage of 5 V 4 Y5UH5Z Applied voltage of V 4 Y5UA5Z Applied voltage of V (Ω) (Ω) (Ω) Time (hr.) Time (hr.) Time (hr.) 6 Multilayer Ceramic Capacitors Vol.