SMD 3R3 3R3. (Unit: mm) (6) (1) (1) (4) Choke; Dimension (2) (3) (4) (5) (6) Production Inductance. A,B,C,D...T...etc., etc. N:±30% Unit A 7.

Transcription

1 . Scope This is applied to the Pb freee high current type SMD inductor for ZLRH6D8CXXXXX Series.. Part Number Code ZLRH 6D8 C R M T () () () () () () (6) () () () () (6) Series Number: ZLMR Magnetic bead; ZLDL Multilayer Inductor; ZLMS Common Mode Choke; ZLNR Magnetic Inductance; ZLML High Frequency Winding inductance; ZLHC Power Inductor; ZLS Color Loop Inductance; ZLW DR Core; ZLRH Shielding Inductance; ZLSR Integrated Inductor; etc. Dimensionn Code: 00/060/080/D8/D8/6D8/8D/0R//00 etc. Production Code: Inductance Code: A,B,C,D...T...etc., for example: 0=MH; =.MH; 0=00uH; 00=0uH; R= =.uh; R0=00NH; N=.NH; N0=0.NH; etc. Tolerance Code: G: ± % J:±% K:±0% L: ±% M: P:±% N:±0% Packaging Code: T Tape; B Bulk. External Dimensions (Unit: mm) R Position Dimension Unit A 7.0 B 7.0 C.0 D.0 Ref. mm E 6.±0. mm F 6.±0. mm G 9.. Materials List 6 Item BARE CORE RING CORE WIRE SOLDER CLIP EPOXY Description&Type DR 6.6* *.7 B.F.7 JNH RI 6.7*.7*.6 JNH ø0.mm (UEW/H) Sn C 6D8 G00/H0 Remark Page of 6

2 . Electrical Characteristics ZLRH6D8 Series P/N L(uH) Tolerance Test Frequency DCR(mΩ) Isat(A) Marking ZLRH6D8CRMT..8 R ZLRH6D8CR0MT.0.88 R ZLRH6D8C6RMT R ZLRH6D8C7RMT 7..8 R7 ZLRH6D8C8R7MT R7 ZLRH6D8C00MT ZLRH6D8C0MT.6 0 ZLRH6D8C0MT ZLRH6D8C80MT ZLRH6D8C0MT 9. 0 ZLRH6D8C70MT ZLRH6D8C0MT.08 0 ZLRH6D8C90MT ZLRH6D8C70MT ZLRH6D8C60MT ZLRH6D8C680MT ZLRH6D8C80MT ZLRH6D8C0MT Remark: The table is not all the P/N of D8 Series, but summary the main P/N. Page of 6

3 6. Reliability Test Electrical Performance Test L DCR Refer to standard Electrical Characteristic RATED CURRENT TEMPERATURE RISE List 0 Max.( t) OVER LOAD No Evidence of Electrical Damage 06 LCZ OR EQUIV. HK0BC OR EQUIV. Applier the current to coils the inductance change should be less than % of initial value and temperaturee not be more than 0. Applied the allowed DC current for Hours. Temperature measured by digital surface thermometer. APPLIED. TIMES OF RATED ALLOWED DC CURRENT TO FOR A PERIOD OF MINUTES. Mechanical Performance Test SOLDER HEAT RESISTANCE VIBRATION (LOW FREQUENCY) SHOCK SHOULD HAVE NO EVIDENCE OF ELECTRICAL DAMAGE INDUCTANCE SHOULD NOT CHANGE MORE THAN 0% PREHEAT:0 00s Max. SOLDER:(Sn99.) SOLDER TEMPERATURE:60 ± DIP TIME:0s Max. AMPLITUDE:.mm; DIRECTIONS:X,Y,Z REQUENCY:0 0Hz/ Minute. SHOULD BE DROPPED 0 TIMES FROM A HEIGHT OF m ONTO cm WOODEN BOARD. SOLDERABILITY More than 90% of terminal electrode should be covered with new solder PREHEAT:0 00s Max. SOLDER:(Sn99.) SOLDER TEMPERATURE: ± DIP TIME:0s Max. RESISTANCE TO SOLVENT There should be no case deformation, Change in appearance of marking SHALL WITHSTAND 6 MINUTES OF ALCOHOL 6 (PUSH ) ADHESION.kg Min. THE DIVICE SHOULD BE REFLOW SOLDERED (± FOR 0 SECONDS) TO A TINNED COPPER SUBSTRATE. A DYNOMETER FORCE GAUGE SHOULD BE APPLIED TO THE SIDE OF THE..THE DEVICE MUST WITHSTAND A MINIMUM FORCE OF.kg WITHOUT AILURE OF THE TERMINATIONN 7 (PULL ) ADHESION.kg Min. INSERT 0cm WIRE INTO THE REMAINING OPEN EYE BEND THE ENDS OF EVEN WIRE LENGTHS UPWARD AND WIND TOGETHER. ELECTRODE SHALL NOT BE REMARKABLY DAMAGED. Page of 6

4 Environment Test TEMPERATURE CHARACTERISTIC HUMIDITY LOW TEMPERATURE STORAGE THERMAL SHOCK T HIGH TEMPERATURE STORAGE Appearance: No Damage Inductance: Within 0% of Initial Value ~+8 60 ± 96± HOURS R.H:90 9%RH TEMPERATURE: ± TIME: 96±HOURS. ± FOR 0 MINUTES 8 ± FOR 0 MINUTES. TOTAL: 0 CYCLES APPLIED CURRENT: RATED CURRENT TEMPERATURE:80 ± TIME:96± HOURS. LIFE HIGH TEMPERATURE LOAD LIFE HUMIDITY LOAD LIFE SHOULD BE NO EVIDENCE OF SHORT OR OPEN CIRCUIT TEMPERATURE:8 ± TIME:00± HOURS. LOAD:ALLOWED DC CURRENT. TEMPERATURE:60 ± R.H.:90 9% TIME: :00± HOURS 7. Soldering Recommends Recommendable Reflow soldering profile Page of 6

5 8. Packaging Information Tape Dimension (Unit: mm) Reel Dimension (Unit: mm) Package Dimension and Quantity Amount(PCS) B C W P Material 000 6mm 0mmm 6mm mm Plastic Remark: The Materials are packaged so that no damage will be sustained. The MPQ will be also refer to formal Quotation due to different Customer requirement. Page of 6

6 9. RoHS compliant Declaration We hereby declare that the components delivered to your company are compliant with RoHS directivee 0/6/EU. 0. Attached The Test Report 06 LCZ Test Instruments VR7 T DATA HK-0BC Callipers Test Temperature: ± Test Humidity: 60 7% S P E C L.uH ELECTRICAL CHARACTERISTICS IDC RDC.A mω L(0A)*7% % Max. 87.% % % % % 6.87 DIMENSIONS (UNIT: mm) A B C G D Max. Max. Max. Max. Ref Max.. 87.% Min.. 8.6% R 0..6% X.8 86.% 判定 Page 6 of 6