THICK FILM CHIP NETWORK RESISTOR THICK FILM CHIP NETWORK RESISTOR FEATURES TYPE DESIGNATION R C M L 0 8 W J T L

Transcription

1 THICK FILM CHIP NETORK RESISTOR THICK FILM CHIP NETORK RESISTOR FEATURES Miniature and light weight. Suit for reflow solder. Stable electrical capability, high reliability. Low assembly cost, suit for automatic SMT equipment. Superior mechanical and frequency characteristics. ROHS RoHS compliant TYPE DESIGNATION RCM RCM Series 8P4R 4P2R R C M L J T L Product Terminal Number Terminal Style Value Thick Film Chip Network Resistor T L C V Terminal Number convex type with corner convex type without corne (E-24 ):, Three digits (E-24 series): The first two digits are significant figures and the third one denotes number of zeros. eg:103=10k OOO : Jumper is expressed by OOO. R : Decinial poirt should be expressed by R eg:1r0=1.0 Tolerance Packing Style Lead-free Level F G J K J ( chip jumper) Tolerance 1% 2% 5% 10% 50m T B C Packing Style Tape & Reel Bulk Case Case ( 100ppm) No Terminal Lead-free Marking ( pb content in terminal 100ppm) L Lead-free Level ( 1000ppm) Low Lead ( pb content in resistor body 1000ppm) G ( 100ppm) Low Lead ( pb content in resistor body 100ppm) 1

2 GB/T GB/T REFERENCE STANDARD CONSTRUCTION RCMT/RCML/RCMC RCMT/RCML/RCMC DIMENSIONS AND EQUIVALENT CIRCUIT 2

3 THICK FILM CHIP NETORK RESISTOR TYPE L T P A B C Normal Terminal Style Special / / RCML V RCMC V / DERATING CURVE Percent rat edload Operating Temperature Range Ambient temperature ( ) 70 ( ) For resistors operated in ambient over 70,rated load (power rating or current rating) shall be derated in accordance with the above figure. 3

4 RATINGS Item RCML08 RCMC08 Power Rating 1/16 1/16 1/8 Max.orking Voltage 50V 50V 200V Max.Overload Voltage 100V 100V 400V Jumper Rated Current 1A 1A 2A Jumper Max. Overload Current 2A 3A 5A Temperature Coefficient 10 R 1M : 200ppm/ 1 R<10,1M <R 10M: 400ppm/ 10 R 1M : 100ppm/ 1 R<10,1M <R 10M : 250ppm/ Range 0 chip jumper, 1 ~10M E-24 series E-96 0 chip jumper, 1 ~10M E-24 series E-96 Tolerance 1%, 2%, 5%, 10% chip jumper: 50m 1%, 2%, 5%, 10% chip jumper 50m Operating Temperature Range Rated Temperature -55 ~ = Note Rated Voltage= Power Rating Value or Max. orking Voltage, whichever is lower. CHARACTERISTICS Item Specifications GB/T Test Methods ( GB/T ) Bending Strength R 1.0%R+0.05 (Bending Distance):3mm (duration):10s 1S T.C.R within specified T.C.R -55 ~+125 Measure between -55 ~+125 Temperature Cycling R 1.0%R ~ 2 ~3 ~ min ~normal temperature 2min~3min ~125 30min 5 cycles Short Time Overload R %R Rated voltage or Max. Overload Voltage whichever is lower for 5 seconds 0 : 5S 0 :Apply Max.overload current for 5s. Steady state humidity R 3.0%R+0.1 Chip jumper:r 100m ~95 RH ~95 RH 1000h 4

5 THICK FILM CHIP NETORK RESISTOR Item 70 Load Life Endurance at upper temperature to Solvent Specifications R 3.0%R+0.1 Chip jumper:r 100m R 3.0%R+0.1 Chip jumper:r 100m R 1.0%R+0.05 GB/T Test Methods ( GB/T ) 70 2,1000, (0 ) 1.5 / 70 2,1000h,rated voltage or rated current (0 ) 1.5h on /h off h 10h 1h Dip in chloroethylene for 10h 1h. Insulation 1000M Min 100V, 1,. Apply DC 100V between substrate and termination for 1 minute, then check insulation resistance. to Soldering Heat R 1.0%R s 1s Solderability 95% 95% Cover Min s s Adhesion 5N 10s 1s Applying 5N 10s 1s PACKAGING Tape and reel Paper taping TYPE A B F E unit:mm RCML TYPE P P0 P1 D0 T RCML

6 Embossed taping D0 P0 A0 K0 A0 B0 D1 E F t K0 B0 P P1 t unit:mm TYPE A0 B0 F E t RCMC08 P P0 P1 D0 D1 K Reel unit:mm TYPE M T A B C D / / RCML08/ A B C D M RCMC T Bulk case unit:mm PACKAGING QUANTITY Packaging style Tape and reel Bulk case Bulk RCML08 RCMC08 RCML08 RCMC08 RCML08 RCMC08 PCS Quantity

7 THICK FILM CHIP NETORK RESISTOR The Explanation For The Value Marking IEC E-24 E-96 IEC E-24 E-96 Series Cross-reference List E-24 E-24 series 10 n unit K 10K 100K 1M 10M Table one E-96 E-96 series K 10K 100K 1M 10M Table two

8 E E-24 series: Express resistance value on the glass side with three digits, the first tow digits should be significant and the third one denote number of zeros. Example 33 E E-96 series: Express the resistance value with four digits, the first three digits are significant figures and the fourth denotes the number of zeros. Example 133 Example the decimal point should be expressed by "R" 1 the jumper should be expressed by 0 For the type of, there is no mark on the glass side. For the resistance which don't belong to IEC serial, use the resistance of IEC serial which is most close to the required resistance of non-iec serial for replacement. To get agreement by both party if there special requirement for the marking. 8