SULFURATION-RESISTANT CHIP RESISTOR

Transcription

1 FEATURES ROHS ith good sulfuration-resistant performance Miniature and light weight. Suit for reflow and wave flow solder. Stable electrical capability, high reliability. Low assembly cost, suit for automatic SMT equipment. Superior mechanical and frequency characteristics. RoHS compliant Example TYPE DESIGNATION R H S 0 3 K F T L Product ode Power Rating Series ode Type ode Resistance Temperature oefficient ode Sulfuration-resistant chip resistor ode S Power rating series Normal Power Series Upgraded Power Series ode Type ode K L U M T..R HTR: 0ppm/ 100ppm/ 00ppm/ 0ppm/ ppm/ 00ppm/ Jumper Resistance Value ode Resistance Tolerance ode Packing Style ode Lead-free Level ode (E-4 ) Three digits (E-4 series): The first two digits are significant figures and the third one denotes number of zeros. (E-96 ) Four digits (E-96 series): The first three digits are significant figures and the four one denotes number of zeros. 000 Jumper is expressed by 000. R Decimal point should be expressed by "R". Example 103=10K E =100K E-96 1R0=1.0 ode Tolerance D 0.% F 1% G % J % K 10% F(Jumper) 10m G(Jumper) 0m J(Jumper) 0m ode T B Packing Style Tape & Reel Bulk ase ase ode No Marking L G Lead-free Level ( 100ppm) Terminal Lead-free ( pb content in terminal 100ppm) ( 1000ppm) Low Lead ( pb content in resistor body 1000ppm) ( 100ppm) Low Lead ( pb content in resistor body 100ppm) 1

2 ONSTRUTION AND DIMENSION unit:mm TYPE L t a b

3 APPEARANE, The surface of resistor is covered with Protective oating which hard to fade, and the surface of coating should avoid unevenness. The terminal part is covered equable, the plating is hard to fade, and should avoid unevenness,flaw, pinhole and discoloration. ith a clear mark, the resistor body is crack-free. GB/T GB/T REFERENE STANDARD DERATING URVE Percent rat edload Operating Temperature 0 Range Ambient temperature ( ) 70 ( ) For resistors operated in ambient over 70,rated load (power rating or current rating) shall be derated in accordance with the above figure. 3

4 RATINGS Item Power Rating Normal Power Series Upgraded Power Series (V) Max.orking Voltage (V) Max.Overload Voltage 1/16 / /16 1/ /10 1/8 R0:100 RS0:10 R0:00 RS0:300 1/8 1/4 00 1/4 1/3 00 1/ / 00 1/ 3/ / 00 rated current for chip jumper 1 1 (A) Max.Overload urrent 3 Resistance Temperature oefficient 040:10 R 1M : 00ppm/ 1 R<10,1M <R 10M : ppm/ 040 : 100 R 100K : 0ppm/ R 1M : 100ppm/ 1 R<10,1M <R 10M : 0ppm/ 10M <R M : 00ppm/ Resistance Range 1 ~M 0 E-4 E-96 Resistance Tolerance 1 ~M : 1% % % 10% 10 ~1M : 0.% hip jumper 0m 0m 10m 1% % % 10% hip jumper 0m 0m 10m Operating Temperature Range - ~+1 Rated Temperature 70 = Note Rated Voltage= Power Rating Resistance Value or Max. orking Voltage, whichever is lower. HARATERISTIS Item Bending Strength Specifications R 1.0%R R 0m (J ) R 0m (G ) R 10m (F ) GB/T Test Methods ( GB/T ) (Bending Distance): 040 3mm mm (duration):10s 1S T..R Temperature ycling within specified T..R R 1.0%R R 0m (J ) R 0m (G ) R 10m (F ) - ~+1 Measure between - ~+1-30 ~ ~3 ~ min ~normal temperature min~3min ~1 30min cycles 4

5 Item Short Time Overload Steady state humidity Specifications R.0%R R 0m (J ) R 0m (G ) R 10m (F ) R 3.0%R R 100m (J ) R 40m (G ) R 0m (F ) GB/T Test Methods ( GB/T ).. Rated voltage or Max. Overload Voltage whichever is lower for seconds 0 : S 0 :Apply Max.overload current for s ~9 RH ~9 RH 1000h 70 Load Life R 3.0%R R 100m (J ) R 40m (G ) R 0m (F ) 70,1000, (0 ) 1. / 0. 70,1000h,rated voltage or rated current (0 ) 1.h on /0.h off. Endurance at upper temperature R 3.0%R R 100m (J ) R 40m (G ) R 0m (F ) h Resistance to Solvent R 1.0%R R 0m (J ) R 0m (G ) R 10m (F ) 10h 1h Dip in chloroethylene for 10h 1h. Insulation Resistance 1000M Min 100V, 1,. Apply D 100V between substrate and termination for 1 minute, then check insulation resistance. Resistance to Soldering Heat R 1.0%R R 0m (J ) R 0m (G ) R 10m (F ) 70 10s 1s Solderability sulfuration-resistant 9% 9% over Min without electrical open. 40 s 0.s HS :100ppm :0~60 90%RH 96h resistor should be exposed at a test chamber with concentration of HS : 100ppm; temperature of 0~60 ; humidity of 90%RH for 96 hours. 040 PAKAGING Tape and reel Paper taping

6 D0 P0 T A B E F P P1 TYPE A B F E TYPE P P0 P1 D0 T Embossed taping D0 P0 A0 K0 A0 B0 D1 E F t K0 B0 P P1 t TYPE A0 B0 F E t

7 TYPE P P0 P1 D0 D1 K / / Reel TYPE M T A B D A B D M T Bulk case unit:mm PAKAGING QUANTITY 110 Packaging style Tape and reel Bulk case Bulk Type PS Quantity