SPECIFICATION. TEST INSTRUMENTS CH-1062A LCR METER CH-502BC IMPEDANCE METER I-sat 2.7 typ Amps 90% L0 CH-3302 LCR METER + CH-1320 BIAS Irms ΔT 40

Transcription

1 C rightek (Europe) Limited SPECIFICTION HF COMPLINT 1.MECHNICL & DIMENSIONS (UNIT: mm) C 10.0max J D 5.0ref 151 E F 2.0ref 7.6ref J 17.5max a 2.9ref b 7.0ref c 5.4ref REMRK CIRCUIT c S F a b a PC Layout 2.ELECTRICL REQUIREMENTS: PRMETER L0 DCR SPECIFICTION 150±20% uh 2.1 max 3.TEMPERTURE RTING: 4.PRODUCT IDENTIFICTION: S M C D : Series Name. D : Inductance Tolerance. (M=±20% ) : Dimension. Coer breakage Dimensions : 2*2*1 C : Inductance. (150uH ) TEST INSTRUMENTS CH-1062 LCR METER CH-502C IMPEDNCE METER I-sat 2.7 typ mps 90% L0 CH-3302 LCR METER + CH-1320 IS Irms Operating 200 max -40 ~ +125 mohm mps CONDITION 25±5 ΔT 40 DIGITL THERMOMTER: DM6801

2 rightek (Europe) Limited 5.TESTING DT: PRMETER 6.MIENT CONDITION 7.TEST DT NO MEN UNIT SPECIFICTION MEN TEMPERTURE ± max D E F J C R L0 DCR I-sat uh mohm 150±20% max CONDITION 25± ref 2.0ref 7.6ref 17.5max R mps 2.7 typ 90% L0 ok HUMIDITY ± 10%

3 INDUCTNCE ( uh ) rightek (Europe) Limited 8.INDUCTNCE (uh) VS DC IS (mps) PRT NO % L % % % % % % % % % % CONDITION: 100KHz, 1.0Vrms (7)MRKING: NR DC IS (mps)

4 0 TEMPERTURE C Temperature ( ) 0 Temperature ( ) rightek (Europe) Limited 9.Recommended Soldering Conditions Figure 1. Re-flow Soldering Preheating Soldering Cooling Peak : 245±5 5±0.5 sec or more sec to 120 Sec. Time (Sec.) Within 4 Figure 2. Hand Soldering PRE-HETING SOLDERING NTURL COOLING Preheating Solderin Cooling 280 Within 3 sec Over 1 min. Over 1 min. Over 1 min. Gradual Cooling Gradual Cooling Within 3 sec. Gradual Cooling

5 rightek (Europe) Limited 10. Reliability and Testing Conditions / SMD Power Inductors Item Specification Conditions Operating temperature range Storage temperature and humidity range -40 ~ ±5, 70% RH Max. 230 Preheatin Dipping Cooling Solderability More than 90% of the terminal electrode should be covered with solder ±1.0 Unit: Second Preheating Dipping Cooling 260 Solder Heat Resistance ±0.5 Unit: Second Heat resistance fter 500 hours in 125±5 and 2 hour drying under normal condition. Cold resistance fter 500 hours in -40±5 and 2 hour drying under normal condition. Thermal shock fter 10 cycles of following condition. Step Temperature ( ) Times (min.) 1-40± Room Temperature Within ± Room Temperature Within 3 Humidity Resistance fter 500 hours in 40±2 and 90 to 95% humidity, and 2 hour drying under normal condition. Vibration Test Inductance within ±5% of initial value and appearance shall not break. fter vibration for 1hour, In each of three orientations at sweep vibration (10~55~10Hz) with 1.52mm P-P mplitudes.

6 D W 0 F 0.75 E 11. PCKGING Tape Dimension rightek (Europe) Limited P2 P0 P T 最外层加珍珠棉 90 C R1.7 Ko 中轴加珍珠棉 User Direction of Unreeling Type (mm) (mm) C(mm) D(mm) 13'' x 24mm 24.5 ± ± ± Series Name :S Unit: mm P/N o(mm) o(mm) Ko(mm) P(mm) T(mm) W(mm) PCS/REEL SCTT ± ± ± ± ± ± (7)MRKING: NR60 Packaging Quantity Series Name : S Unit: mm Reel Inner Carton Outer Carton Quantity Reel Quantity Size Inner Carton Quantity Size 200pcs 2 400pcs pcs Storage Transportation 1. Temperature and humidity conditions: Less than 40 and 70% RH. 2. Recommended products should be used within 6 months form the time of delivery. 3. The packaging material should be kept where no chlorine 1. Products should be handled with care to avoid damage or contamination from perspiration and skin oils. 2. The use of tweezers or vacuum pick up is strongly recommended for individual components. 3. ulk handling should ensure that abrasion and mechanical or sulfur exists in the air. shock are minimized.