FACT DATA 5-1 DUAL JK NEGATIVE EDGE-TRIGGERED FLIP-FLOP

Transcription

1 The MC113/T113 consists of o high-speed completely independent transition clocked flip-flops. The clocking operation is independent of rise and fall times of the clock waveform. The design allows operation as a D flip-flop (refer to MC74/T74 data sheet) by connecting the and inputs together. Asynchronous Inputs: LOW input to (Set) sets to HIGH level Set is independent of clock Outputs Source/Sink 24 ma ACT113 Has TTL Compatible Inputs CONNECTION DIAGRAM DUAL NEGATIE EDGE-TRIGGERED FLIP-FLOP N SUFFIX CASE PLASTIC CC D SUFFIX CASE 751A-03 PLASTIC GND 4 LOGIC SYMBOL 10 MODE SELECT TRUTH TABLE Operating Mode Inputs Outputs Set L X X H L Toggle H h h q q Load 0 (Reset) H l h L H Load 1 (Set) H h l H L Hold H l l q q CC = PIN 14 GND = PIN 7 8 H, h = HIGH oltage Level L, l = LOW oltage Level X = Don t Care l, h (q) = Lower case letters indicate the state of the referenced input (or output) one set-up time prior to the HIGH to LOW clock transition. 5-1

2 MC113 MCT113 LOGIC DIAGRAM (Each Flip-Flop) 5(9) 6(8) 3(11) SET () 4(10) 2(12) 1(13) CLOC () MAXIMUM RATINGS* alue CC DC Supply oltage (Referenced to GND) 0.5 to +7.0 in DC Input oltage (Referenced to GND) 0.5 to CC +0.5 out DC Output oltage (Referenced to GND) 0.5 to CC +0.5 Iin DC Input Current, per Pin ±20 ma Iout DC Output Sink/Source Current, per Pin ±50 ma ICC DC CC or GND Current per Output Pin ±50 ma Tstg Storage Temperature 65 to +150 C * Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. RECOMMENDED OPERATING CONDITIONS Min Max CC Supply oltage AC ACT in, out DC Input oltage, Output oltage (Ref. to GND) 0 CC Input Rise and Fall Time (Note 1) tr, r tff AC Devices except Schmitt Inputs tr, tf ns/ Input Rise and Fall Time (Note 2) ACT Devices except Schmitt Inputs T unction Temperature (PDIP) 140 C TA Operating Ambient Temperature Range C IOH Output Current High 24 ma IOL Output Current Low 24 ma 1. in from 30% to 70% CC ; see individual Data Sheets for devices that differ from the typical input rise and fall times. 2. in from 0.8 to 2.0 ; see individual Data Sheets for devices that differ from the typical input rise and fall times. ns/ 5-2

3 DC CHARACTERISTICS MC113 MCT113 CC () TA = 40 C Guaranteed Limits Conditions IH Minimum High Level OUT = 0.1 Input oltage or CC IL Maximum Low Level OUT = 0.1 Input oltage or CC OH Minimum High Level IOUT = 50 µa Output oltage *IN = IL or IH ma IOH 24 ma ma OL Maximum Low Level IOUT = 50 µa Output oltage IIN IOLD IOHD ICC Maximum Input Leakage Current Minimum Dynamic Output Current Maximum uiescent Supply Current *IN = IL or IH ma IOL 24 ma ma 5.5 ±0.1 ±1.0 µa I = CC, GND ma OLD = 1.65 Max ma OHD = 3.85 Min µa IN = CC or GND * All outputs loaded; thresholds on input associated with output under test. Maximum test duration 2.0 ms, one output loaded at a time. Note: I IN and I 3.0 are guaranteed to be less than or equal to the respective 5.5 CC. AC CHARACTERISTICS (For Figures and Waveforms See Section 3) CC* () Min Max Min Max Maximum Clock fmax Frequency tplh n to n or n tphl n to n or n tplh n to n tphl n to n MHz 3-3 * oltage Range 3.3 is 3.3 ±0.3. oltage Range 5.0 is 5.0 ±

4 MC113 MCT113 AC OPERATING REUIREMENTS ts th trec CC* () Guaranteed Minimum Set-up Time, HIGH or LOW n or n to n Hold Time, HIGH or LOW n or n to n Pulse Width Clock Pulse Width n Recovery TIme n to * oltage Range 3.3 is 3.3 ±0.3. oltage Range 5.0 is 5.0 ±0.5. ns 3-9 ns 3-9 ns 3-9 DC CHARACTERISTICS CC () T T TA = 40 C Guaranteed Limits IH Minimum High Level Input oltage IL Maximum Low Level Input oltage OH Minimum High Level Output oltage Conditions OUT = 0.1 or CC 0.1 OUT = 0.1 or CC 0.1 IOUT = 50 µa OL Maximum Low Level Output oltage *IN = IL or IH 24 ma IOH 24 ma IOUT = 50 µa IIN Maximum Input Leakage Current *IN = IL or IH ma IOL 24 ma 5.5 ±0.1 ±1.0 µa I = CC, GND ICCT Additional Max. ICC/Input ma I = CC 2.1 IOLD IOHD ICC Minimum Dynamic Output Current Maximum uiescent Supply Current ma OLD = 1.65 Max ma OHD = 3.85 Min µa IN = CC or GND * All outputs loaded; thresholds on input associated with output under test. Maximum test duration 2.0 ms, one output loaded at a time. 5-4

5 MC113 MCT113 AC CHARACTERISTICS (For Figures and Waveforms See Section 3) fmax tplh tphl tplh tphl Maximum Clock Frequency n to n or n n to n or n n to n n to n * oltage Range 5.0 is 5.0 ±0.5. CC* () T T Min Max Min Max MHz AC OPERATING REUIREMENTS ts Set-up Time, HIGH or LOW n or n to n th Hold Time, HIGH or LOW n or n to n Pulse Width Clock Pulse Width n trec Recovery TIme n to * oltage Range 5.0 is 5.0 ±0.5. CC* () T T Guaranteed Minimum ns ns ns 3-9 CAPACITANCE alue Test Conditions CIN Input Capacitance 4.5 pf CC = 5.0 D Power Dissipation Capacitance 35 pf CC =

6 MC113 MCT113 OUTLINE DIMENSIONS A F H G D N B SEATING PLANE C N SUFFIX PLASTIC DIP PACAGE CASE ISSUE L L M NOTES: 1. LEADS WITHIN 0.13 (0.005) RADIUS OF TRUE POSITION AT SEATING PLANE AT MAXIMUM MATERIAL CONDITION. 2. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 3. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 4. ROUNDED CORNERS OPTIONAL. INCHES MILLIMETERS DIM MIN MAX MIN MAX A B C D F G BSC 2.54 BSC H L BSC 7.62 BSC M N A B P 7 PL D SUFFIX PLASTIC SOIC PACAGE CASE 751A 03 ISSUE F 0.25 (0.010) M B M NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. T SEATING PLANE G D 14 PL C 0.25 (0.010) M T B S A S R X 45 M F MILLIMETERS INCHES DIM MIN MAX MIN MAX A B C D F G 1.27 BSC BSC M P R Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. ical parameters can and do vary in different applications. All operating parameters, including icals must be validated for each customer application by customer s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE: Motorola Literature Distribution; APAN: Nippon Motorola Ltd.; Tatsumi SPD LDC, Toshikatsu Otsuki, P.O. Box 20912; Phoenix, Arizona F Seibu Butsuryu Center, Tatsumi oto u, Tokyo 135, apan MFAX: RMFAX0@ .sps.mot.com TOUCHTONE (602) HONG ONG: Motorola Semiconductors H.. Ltd.; 8B Tai Ping Industrial Park, INTERNET: NET.com 51 Ting ok Road, Tai Po, N.T., Hong ong MC113/D