IntesisBox HS-RC-KNX-1i v1.1

Transcription

1 IntesisBx HS-RC-KNX-1i v1.1 KNX (TP-1) Interface fr HISENSE VRF Air Cnditining. User's Manual Issue Date: 01/2018 r1.0 EN Order Cde: IBKNXHIS001R000

2 IntesisBx KNX Hisense Intesis Sftware S.L.U. All Rights Reserved. Infrmatin in this dcument is subject t change withut prir ntice. The sftware described in this dcument is furnished under a license agreement r nndisclsure agreement. The sftware may be used nly in accrdance with the terms f thse agreements. N part f this publicatin may be reprduced, stred in a retrieval system r transmitted in any frm r any means electrnic r mechanical, including phtcpying and recrding fr any purpse ther than the purchaser s persnal use withut the written permissin f Intesis Sftware S.L.U. Intesis Sftware S.L.U. Milà i Fntanals, 1 bis Igualada Spain TRADEMARKS All trademarks and trade names used in this dcument are acknwledged t be the cpyright f their respective hlders. Infrmatin in this dcument is subject t changes withut prir ntice. Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 2 / 60

3 IntesisBx KNX Hisense INDEX 1. Presentatin Cnnectin HS-RC-KNX-1i withut Hisense Remte Cntrller HS-RC-KNX-1i with HISENSE Remte Cntrller Cnfiguratin and setup ETS Parameters General dialg HS-RC-KNX-1i is master in AB bus Send READs fr Cntrl_ bjects n bus recvery Scene t lad n bus recvery / startup Disallw cntrl frm remte cntrller Enable func Cntrl_ Lck Cntrl Obj Enable use f bjects fr Filter Enable func Operating Time Cunter Enable bject Errr Cde [2byte] Enable bject Errr Text Cde [14byte] Mde Cnfiguratin dialg When Mde is AUTO Status_ bjs reprt actual perating status (HEAT/COOL/..) Enable use f Heat / Cl bit-type bj Enable PID-Cmpat. Scaling Mde Objects Enable use f +/- bject fr Mde Enable use f bit-type Mde bjects (fr cntrl) Enable use f bit-type Mde bjects (fr status) Enable use f Text bject fr Mde Special Mdes Cnfiguratin dialg Enable use f POWER mde Enable use f ECONOMY mde Enable use f ADDITIONAL HEATING mde Enable use f ADDITIONAL COOLING mde Fan Speed Cnfiguratin dialg Available fan speeds in Indr Unit Indr unit has AUTO fan speed DPT bject type fr fanspeed Enable use f +/- bject fr Fan Speed Enable use f bit-type Fan Speed bjects (fr Cntrl) Enable use f bit-type Fan Speed bjects (fr Status) Enable use f Text bject fr Fan Speed Vanes Up-Dwn Cnfiguratin dialg Indr unit has U-D Vanes Available psitins in Indr Unit DPT bject type fr Vanes Up-Dwn Enable use f +/- bject fr Vanes U-D Enable use f bit-type Vane U-D bjects (fr Cntrl) Enable use f bit-type Vane U-D bjects (fr Status) Enable Vanes U-D Swing bjects (fr Cntrl and Status) Enable use f Text bject fr Vane U-D Temperature Cnfiguratin dialg Peridic sending f Status_ AC Setp Transmissin f Status_ AC Reference Temp Enable use f +/- bject fr Setpint Temp Enable limits n Cntrl_ Setpint bj Ambient temp. ref. is prvided frm KNX Scene Cnfiguratin dialg Enable use f scenes Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 3 / 60

4 IntesisBx KNX Hisense Scenes can be stred frm KNX bus Enable use f bit bjects fr scene executin Scene x preset Switch-Off Timeuts Cnfiguratin dialg Enable use f Open Windw / Switch ff timeut functin Enable use f Occupancy functin Enable use f SLEEP timeut Binary Input x Cnfiguratin dialg Enable use f Input x Cntact type Debunce time Disabling functin Functin Specificatins AC Unit Types cmpatibility Errr Cdes Appendix A Cmmunicatin Objects Table Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 4 / 60

5 IntesisBx KNX Hisense 1. Presentatin HS-RC-KNX-1i allws a cmplete and natural integratin f HISENSE air cnditiners with KNX cntrl systems. Cmpatible with VRF air cnditiners cmmercialized by HISENSE. Main features: Reduced dimensins, quick installatin. Multiple bjects fr cntrl and status (bit, byte, characters ) with KNX standard datapint types. Status bjects fr every cntrl available. Timeut fr Open Windw and Occupancy. Sleep functin als available. Cntrl f the AC unit based in the ambient temperature read by the wn AC unit, r in the ambient temperature read by any KNX thermstat. AC unit can be cntrlled simultaneusly by the wired remte cntrl f the AC unit and by KNX. Direct cnnectin t the AC indr unit. Ttal Cntrl and Mnitring f the AC unit frm KNX, including mnitring f AC unit s state f internal variables, running hurs cunter (fr filter maintenance cntrl), and errr indicatin and errr cde. Up t 5 scenes can be saved and executed frm KNX, fixing the desired cmbinatin f Operatin Mde, Set Temperature, Fan Speed, Vane Psitin and Remte Cntrller Lck in any mment by using a simple switching. Fur ptential-free binary inputs prvide the pssibility t integrate many types f external devices. Cnfigurable frm ETS t, they can be used fr switching, dimming, shutter/blind cntrl, and mre. Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 5 / 60

6 IntesisBx KNX Hisense 2. Cnnectin Cnnectin f the HS-RC-KNX-1i t the AC indr unit 2.1 HS-RC-KNX-1i withut Hisense Remte Cntrller The HS-RC-KNX-1i can be cnnected directly t the AB bus f the indr unit (n HISENSE remte cntrller -RC frm nw n- als cnnected in the AB bus). If this is the case, HS- RC-KNX-1i must be cnfigured as master (using the ETS sftware), see cnnectin diagram belw. 2.2 HS-RC-KNX-1i with HISENSE Remte Cntrller If a HISENSE remte cntrller (RC) is present and cnnected t the AB bus, cnnect the gateway as Slave in parallel with the wired remte cntrllers (cntrller acts as Master). Wired remte cntrl available. Discnnect mains pwer frm the AC unit and use a 2-wire cable with a diameter f 0.75mm 2 t 1.25mm 2 fr the cnnectin f HS-RC-KNX-1i, Hisense remte cntrller and its crrespnding indr unit. Screw the suitably peeled cable ends in the crrespnding AB terminals f each device, as summarized in the Figure 2.2. Maximum AB bus length is 500 meter. HISENSE RC and HS-RC-KNX-1i are n plarity dependent. Cnnectin f the HS-RC-KNX-1i t the KNX bus: Discnnect pwer f the KNX bus. Cnnect the HS-RC-KNX-1i t the KNX TP-1 (EIB) bus using the KNX standard cnnectr (red/grey) f the HS-RC-KNX-1i, respect plarity. Recnnect pwer f the KNX bus, and mains pwer f the AC unit. Cnnectin diagrams: HS-RC-KNX-1i withut HISENSE RC Binary inputs fr ptential-free cntacts. AC Indr Unit IntesisBx COM IN4 IN3 IN2 IN1 KNX AC Unit A B KNX TP-1 (EIB) bus Internal electrnic cntrl B A HS-RC-KNX-1i Cnnectin t AB bus. Tw wire cable. Max.500 m Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 6 / 60

7 IntesisBx KNX Hisense HS-RC-KNX-1i with HISENSE RC Remte Cntrller Binary inputs fr ptential-free cntacts. HISENSE AC Indr Unit Internal electrnic cntrl A B A B IntesisBx COM IN4 IN3 IN2 IN1 KNX AC Unit A B HS-RC-KNX-1i KNX TP-1 (EIB) bus Cnnectin t AB bus. Tw wire cable. Max. 500 m Figure 2.2 HS-RC-KNX-1i cnnectin diagrams Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 7 / 60

8 IntesisBx KNX Hisense 3. Cnfiguratin and setup This is a fully cmpatible KNX device which must be cnfigured and setup using standard KNX tl ETS. ETS database fr this device can be dwnladed frm: 1i_ets_database.zip Please cnsult the README.txt file, lcated inside the dwnladed zip file, t find instructins n hw t install the database. Imprtant: D nt frget t select the crrect settings f AC indr unit being cnnected t the HS-RC-KNX-1i. This is in "Parameters" f the device in ETS. Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 8 / 60

9 IntesisBx KNX Hisense 4. ETS Parameters When imprted t the ETS sftware fr the first time, the gateway shws the fllwing default parameter cnfiguratin: Figure 4.1 Default parameter cnfiguratin With this cnfiguratin it s pssible t send On/Off (Cntrl_ On/Off), change the AC Mde (Cntrl_ Mde), the Fan Speed (Cntrl_ Fan Speed), the Vane Psitin (Cntrl_ Vanes U-D) and als the Setpint Temperature (Cntrl_ Setpint Temperature). The Status_ bjects, fr the mentined Cntrl_ bjects, are als available t use if needed. Als bjects Status_ AC Reference Temp and Status_ Errr/Alarm are shwn. Figure 4.2 Default cmmunicatin bjects Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 9 / 60

10 IntesisBx KNX Hisense 4.1 General dialg Inside this parameter s dialg it is pssible t activate r change the parameters shwn in the Figure 4.1. The first field shws the where t dwnlad the database and the user manual fr the prduct HS-RC-KNX-1i is master in AB bus This parameter changes the gateway s behavir, being able t prgram it as master r slave in AB bus. If set t n, the gateway will wrk as a slave and it will be necessary t have a Hisense remte cntrller cnfigured as a master. If set t yes the gateway will be master f the bus. It is nt necessary t have any Hisense remte cntrller in this case but, if there are, they must be cnfigured as slave. The next parameter is als shwn when selecting HS-RC-KNX-1i as master in AB bus: Figure 4.3 Parameter detail Send READs fr Cntrl_ bjects n bus recvery When this parameter is enabled, HS-RC-KNX-1i will send READ egrams fr the grup addresses assciated n its Cntrl_ bjects n bus recvery r applicatin reset/start-up. If set t n the gateway will nt perfrm any actin. If set t yes all Cntrl_ bjects with bth Transmit (T) and Update (U) flags enabled will send READs and their values will be updated with the respnse when received. Delay befre sending READs (sec): Figure 4.4 Parameter detail With this parameter, a delay can be cnfigured between 0 and 30 secnds fr the READs sent by the Cntrl_ bjects. This is t give time enugh t ther KNX devices n the bus t start-up befre sending the READs. Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 10 / 60

11 IntesisBx KNX Hisense Scene t lad n bus recvery / startup This parameter executes a selected scene n bus recvery r startup, nly if the selected scene has an enabled preset r values previusly saved frm KNX bus (see Scene Cnfiguratin dialg). If the gateway is discnnected frm the indr unit the scene will nt be applied, even when cnnecting t the indr unit again. Figure 4.5 Parameter detail Disallw cntrl frm remte cntrller This parameter allws: 1- Having the remte cntrller always lcked, r 2- Decide thrugh a new cmmunicatin bject if the RC is lcked r nt. If set t yes all the actins perfrmed thrugh the remte cntrller will be disabled. If set t n the remte cntrller will wrk as usually. It als appears a new parameter and the cmmunicatin bject Cntrl_ Lck Remte Cntrl. 36 Figure 4.6 Cmmunicatin bject and parameter detail Enable cmm bj Ctrl_ Remte Lck : If set t n the bject will nt be shwn. If set t yes the Cntrl_ Lck Remte Cntrl bject will appear. When a 1 value is sent t this cmmunicatin bject, the remte cntrller is lcked. T be unlcked a 0 value must be sent. The gateway remembers the last value received even if a KNX bus reset/failure happens. Imprtant: If an initial scene is enabled and it has as Value fr Remte Lck (unchanged) r unlcked, this wuld unlck the remte cntrller because the initial scene has pririty ver the Cntrl_ Lck Remte Cntrl cmmunicatin bject Enable func Cntrl_ Lck Cntrl Obj This parameter shws/hide the Cntrl_ Lck Cntrl Obj cmmunicatin bject which, depending n the sent value, lcks r unlcks ALL the Cntrl_ cmmunicatin bjects except itself. Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 11 / 60

12 IntesisBx KNX Hisense 37 If set t n the bject will nt be shwn. If set t yes the Cntrl_ Lck Cntrl Objects bject will appear. When a 1 value is sent t this cmmunicatin bject, all the Cntrl_ bjects will be lcked. T unlck a 0 value must be sent, as the gateway remembers the last value received even if a KNX bus reset/failure happens Enable use f bjects fr Filter This parameter shws/hides Cntrl_ Reset Filter and Status_ Filter Status that lets reset the filter status and als mnitr if there is a filter alarm If set t n the bject will nt be shwn. If set t yes Cntrl_ Reset Filter and Status_ Filter Status bjects will appear. When a 0 value is shwn in the Status_ bject, it indicates n filter alarm. When a 1 value is shwn in the Status_ bject, it indicates that the filter is full. Once the filter has been cleaned, alarm shuld be reset sending a 1 value t the Cntrl_ Reset Filter bject Enable func Operating Time Cunter This parameter shws/hides the Status_ Operatin Sec Cunter cmmunicatin bject which cunts the number f perating secnds fr the HS-RC-KNX-1i. If set t n the bject will nt be shwn. If set t yes the Status_ Operatin Time Cunter bject will appear. It als appears a new parameter. This bject can be read and sends its status every time a whle functining hur (3600s) is cunted. The gateway keeps that cunt in memry and the status is sent als after a KNX bus reset/failure. Althugh this bject is marked as a Status_ bject it als can be written t update the cunter when needed. T reset the cunter shuld be written a 0 value. Imprtant: This bject cmes by default withut the write (W) flag activated. If is necessary t write n it, this flag must be activated. Imprtant: This bject will als return its status, every time a value is written, nly if it s different frm the existing ne. Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 12 / 60

13 IntesisBx KNX Hisense Imprtant: If the stred value is 0 hurs, the gateway will nt send the status t KNX. Enable func Operating Hurs Cunter : If set t n the bject will nt be shwn. If set t yes the Cntrl_ Operatin Hur Cunter bject will appear. It prvides same functinality as Status_ Operating Sec Cunter but prvides infrmatin in hurs instead f secnds. 96 Imprtant: This bject cmes by default withut the write (W) flag activated. If is necessary t write n it, this flag must be activated. Imprtant: This bject will als return its status, every time a value is written, nly if it s different frm the existing ne. Imprtant: If the stred value is 0 hurs, the gateway will nt send the status t KNX Enable bject Errr Cde [2byte] This parameter shws/hides the Status_ Errr Cde cmmunicatin bject which shws the indr unit errrs, if ccurred, in numeric frmat. 88 If set t n the bject will nt be shwn. If set t yes the Status_ Errr Cde [2byte] bject will appear. This bject can be read and als sends the indr unit errr, if ccurred, in numeric frmat. If a 0 value is shwn that means n errr Enable bject Errr Text Cde [14byte] This parameter shws/hides the Status_ Errr Text Cde cmmunicatin bject which shws the indr unit errrs, if ccurred, in text frmat. 89 If set t n the bject will nt be shwn. Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 13 / 60

14 IntesisBx KNX Hisense If set t yes the Status_ Errr Text Cde bject will appear. This bject can be read and als sends the indr unit errr, if ccurred, in text frmat. The errrs shwn have the same frmat as at the remte cntrller and at the errr list frm the indr unit manufacturer. If the bject s value is empty that means n errr. 4.2 Mde Cnfiguratin dialg Figure 4.7 Default Mde Cnfiguratin dialg All the parameters in this sectin are related with the different mde prperties and cmmunicatin bjects. 1 The byte-type cmmunicatin bject fr Mde wrks with the DTP_ Aut mde will be enabled with a 0 value, Heat mde with a 1 value, Cl mde with a 3 value, Fan mde with a 9 value and Dry mde with a 14 value When Mde is AUTO Status_ bjs reprt actual perating status (HEAT/COOL/..) When set t n (default) Status_ bjects fr perating mde will reprt AUTO as perating mde while indr unit is in AUTO mde. If set t yes, Status_ bjects fr perating mde will reprt actual perating mde f the whle system ( HEAT r COOL ), accrding t status reprted by the indr unit Enable use f Heat / Cl bit-type bj This parameter shws/hides the Cntrl_ and Status_ Mde Cl/Heat cmmunicatin bjects Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 14 / 60

15 IntesisBx KNX Hisense If set t n the bjects will nt be shwn. If set t yes the Cntrl_ and Status_ Mde Cl/Heat bjects will appear. When a 1 value is sent t the Cntrl_ cmmunicatin bject, Heat mde will be enabled in the indr unit, and the Status_ bject will return this value. When a 0 value is sent t the Cntrl_ cmmunicatin bject, Cl mde will be enabled in the indr unit, and the Status_ bject will return this value Enable PID-Cmpat. Scaling Mde Objects This parameter shws/hides the Cntrl_ Mde Cl & On and Cntrl_ Mde Heat & On cmmunicatin bjects. 3 4 If set t n the bjects will nt be shwn. If set t yes the Cntrl_ Mde Cl & On and Cntrl_ Mde Heat & On bjects will appear. These bjects prvide cmpatibility with thse KNX thermstats that cntrl the demand f heating r cling by using scaling (percentage) bjects. In these thermstats, the percentage demand is meant t be applied n a fluid valve f the heating / cling system. HS-RC-KNX-1i device des nt prvide individual cntrl n the internal parts f the indr unit (as can be its cmpressr, refrigerant valves, etc). Rather, it prvides the same level f cntrl as a (user) remte cntrller. Objects Cntrl_ Mde Cl & On and Cntrl_ Mde Heat & On intend t bring cmpatibility between thermstats riented t the cntrl f custm heating / cling systems and ready-made AC indr units, by applying the fllwing lgic: Whenever a nn-zer value (>0%) is received at Cntrl_ Mde Cl & On, indr unit will switch On in COOL mde. Whenever a nn-zer value (>0%) is received at Cntrl_ Mde Heat & On, indr unit will switch On in HEAT mde. Lastest updated bject will define the perating mde Indr unit will switch ff nly when bth bjects becme zer (0%) r when an OFF is requested at bject 0. On/Off [DPT_ bit] Imprtant: These bjects functin is nly t send On/Off and Cl/Heat t the indr unit. The PID (Inverter system) is calculated by the indr unit itself. Please cnsider Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 15 / 60

16 IntesisBx KNX Hisense intrducing an apprpriate PID cnfiguratin t the external KNX thermstat t nt interfere the indr unit PID Enable use f +/- bject fr Mde This parameter shws/hides the Cntrl_ Mde -/+ cmmunicatin bject which lets change the indr unit mde by using tw different datapint types. 10 If set t n the bject will nt be shwn. If set t yes the Cntrl_ Mde -/+ bject and a new parameter will appear. Figure 4.8 Parameter detail DPT type fr +/- Mde Object This parameter lets chse between the datapints 0-Up / 1-Dwn [DPT_1.008] and 0-Decrease / 1-Increase [DPT_1.007] fr the Cntrl_ Mde -/+ bject. The sequence fllwed when using this bject is shwn belw: AUTO HEAT COOL FAN DRY Up / Increase Dwn / Decrease Imprtant: Read the dcumentatin f yur indr unit t check if it has AUTO mde available Enable use f bit-type Mde bjects (fr cntrl) This parameter shws/hides the bit-type Cntrl_ Mde bjects If set t n the bjects will nt be shwn. Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 16 / 60

17 IntesisBx KNX Hisense If set t yes the Cntrl_ Mde bjects fr Aut, Heat, Cl, Fan and Dry will appear. T activate a mde by using these bjects a 1 value has t be sent Enable use f bit-type Mde bjects (fr status) This parameter shws/hides the bit-type Status_ Mde bjects If set t n the bjects will nt be shwn. If set t yes the Status_ Mde bjects fr Aut, Heat, Cl, Fan and Dry will appear. When enabled, a mde will return a 1 thrugh its bit-type bject Enable use f Text bject fr Mde This parameter shws/hides the Status_ Mde Text cmmunicatin bject. 65 If set t n the bject will nt be shwn. If set t yes the Status_ Mde Text bject will appear. Als, in the parameters, will be shwn five text fields, ne fr each mde, that will let mdify the text string displayed by the Status_ Mde Text when changing mde. Figure 4.9 Parameter detail 4.3 Special Mdes Cnfiguratin dialg Figure 4.10 Default Special Mdes Cnfiguratin dialg Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 17 / 60

18 IntesisBx KNX Hisense The Special Mdes can be parameterized thrugh the ETS parameters dialg, and they can be used t give extra functinality. Imprtant: When executing any f the Special Mdes the real state f the indr unit will NOT be shwn in KNX. Imprtant: When the predefined time fr the Special Mde is finished r a 0 value is sent t stp it, the previus state will be recvered. Imprtant: If a value cncerning On/Off, Mde, Fan Speed r Setpint Temperature is received frm KNX while any Special Mde is running ( 1 ), the Special Mde will stp and the previus state will be recvered. The value received will be als applied then. Imprtant: If a value cncerning On/Off, Mde, Fan Speed r Setpint Temperature is mdified thrugh the remte cntrller, the Special Mde will stp WITHOUT recvering the previus state. Then the real indr unit state will be shwn in KNX including the new value received thrugh the remte cntrller Enable use f POWER mde This parameter shws/hides the Cntrl_ Pwer Mde and Status_ Pwer Mde cmmunicatin bjects. The Pwer Mde lets change the Setpint Temperature and the Fan Speed within a given perid f time If set t n the bjects will nt be shwn. If set t yes the Cntrl_ Pwer Mde and Status_ Pwer Mde bjects and new parameters will appear. Figure 4.11 Parameter detail When a 1 value is sent t the Cntrl_ cmmunicatin bject Pwer Mde will be enabled, and the Status_ bject will return this value. When a 0 value is sent t the Cntrl_ cmmunicatin bject, Pwer Mde will be disabled, and the Status_ bject will return this value. Imprtant: This mde will ONLY wrk if the indr unit is bth turned n and in a Heat, Cl, Aut-Heat r Aut-Cl Mde. Actin time fr this mde (minutes): Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 18 / 60

19 IntesisBx KNX Hisense Duratin f Pwer Mde, in minutes, nce started. Setpint delta increase (HEAT) r decrease (COOL) in Celsius: Number f degrees Celsius that will increase in Heat Mde, r decrease in Cl Mde, while in Pwer Mde. Fan Speed fr this mde: Fan Speed that will be set in the unit while in Pwer Mde Enable use f ECONOMY mde This parameter shws/hides the Cntrl_ Ecn Mde and Status_ Ecn Mde cmmunicatin bjects. The Ecn Mde lets change the Setpint Temperature and the Fan Speed within a given perid f time If set t n the bjects will nt be shwn. If set t yes the Cntrl_ Ecn Mde and Status_ Ecn Mde bjects and new parameters will appear. When a 1 value is sent t the Cntrl_ cmmunicatin bject, EcnMde will be enabled, and the Status_ bject will return this value. When a 0 value is sent t the Cntrl_ cmmunicatin bject, EcnMde will be disabled, and the Status_ bject will return this value. Imprtant: This mde will ONLY wrk if the indr unit is bth turned n and in a Heat, Cl, Aut-Heat r Aut-Cl Mde. Actin time fr this mde (minutes): Duratin f EcnMde, in minutes, nce started. Setpint delta increase (HEAT) r decrease (COOL) in Celsius: Number f degrees Celsius that will increase in Heat Mde, r decrease in Cl Mde, while in EcnMde. Fan Speed fr this mde: Fan Speed that will be set in the unit while in EcnMde. Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 19 / 60

20 IntesisBx KNX Hisense Enable use f ADDITIONAL HEATING mde This parameter shws/hides the Cntrl_ Additinal Heat Mde and Status_ Additinal Heat Mde cmmunicatin bjects. The Additinal Heating Mde lets change the Setpint Temperature and the Fan Speed within a given perid f time If set t n the bjects will nt be shwn. If set t yes the Cntrl_ Start Additinal Heat Mde and Status_ Additinal Heat Mde bjects and new parameters will appear. When a 1 value is sent t the Cntrl_ cmmunicatin bject, Additinal Heating Mde will be enabled, and the Status_ bject will return this value. When a 0 value is sent t the Cntrl_ cmmunicatin bject, Additinal Heating Mde will be disabled, and the Status_ bject will return this value. Imprtant: This mde will ALWAYS turn n the indr unit in Heat mde. Actin time fr this mde (minutes): Duratin f Additinal Heating Mde, in minutes, nce started. Setpint temp fr this mde (ºC): Setpint temperature that will be applied while in Additinal Heating Mde. Fan Speed fr this mde: Fan Speed that will be set in the unit while in Additinal Heating Mde Enable use f ADDITIONAL COOLING mde This parameter shws/hides the Cntrl_ Additinal Cl Mde and Status_ Additinal Cl Mde cmmunicatin bjects. The Additinal Heating Mde lets change the Setpint Temperature and the Fan Speed within a given perid f time If set t n the bjects will nt be shwn. If set t yes the Cntrl_ Start Additinal Cl Mde and Status_ Additinal Cl Mde bjects and new parameters will appear. When a 1 value is sent t the Cntrl_ cmmunicatin bject, Additinal Cling Mde will be enabled, and the Status_ bject will return this value. Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 20 / 60

21 IntesisBx KNX Hisense When a 0 value is sent t the Cntrl_ cmmunicatin bject, Additinal Cling Mde will be disabled, and the Status_ bject will return this value. Imprtant: This mde will ALWAYS turn n the indr unit in Cl mde. Actin time fr this mde (minutes): Duratin f Additinal Cling Mde, in minutes, nce started. Setpint temp fr this mde (ºC): Setpint temperature that will be applied while in Additinal Cling Mde. Fan Speed fr this mde: Fan Speed that will be set in the unit while in Additinal Cling Mde. 4.4 Fan Speed Cnfiguratin dialg Figure 4.12 Default Fan Speed Cnfiguratin dialg All the parameters in this sectin are related with the Fan Speed prperties and cmmunicatin bjects Available fan speeds in Indr Unit This parameter lets chse hw many fan speeds are available in the indr unit. Figure 4.13 Parameter detail Imprtant: Read the dcumentatin f yur indr unit t check hw many fan speeds are available. Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 21 / 60

22 IntesisBx KNX Hisense Indr unit has AUTO fan speed This parameter lets chse if AUTO fan speed is available in the indr unit. When Yes is selected, Enable Fan Speed Man/Aut bjects parameter will appear. Enable Fan Speed Man/Aut bjects Figure 4.14 Parameter detail When Yes is selected, bjects Cntrl_ and Status_ Fan Speed Man/Aut will appear When value 1-Aut is received at Cntrl_ bject, indr unit will be set up Aut Fan Speed. When value 0-Manual is received, indr unit will be set up in first speed (fan speed 1). Writing a certain fan speed (1, 2, 3 r 4 (if available)) t its crrespnding cntrl bject will cancel Aut fan speed. Imprtant: Read the dcumentatin f yur indr unit t check if AUTO fan speed is available DPT bject type fr fanspeed With this parameter is pssible t change de DPT fr the Cntrl_ Fan Speed and Status_ Fan Speed byte-type cmmunicatin bjects. Datapints Scaling (DPT_5.001) and Enumerated (DPT_5.010) can be selected. Imprtant: The cmmunicatin bjects shwn in this sectin may be different depending n the number f fan speeds available, althugh they all share the same cmmunicatin bject number. When Enumerated [DPT 5.010] is selected, Cntrl_ Fan Speed and Status_ Fan Speed cmmunicatin bjects fr this DPT will appear The first fan speed will be selected if a 1 is sent t the Cntrl_ bject. The secnd ne will be selected sending a 2 ; the third ne (if available) will be selected sending a 3 ; the furth ne (if available) will be selected sending a 4. Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 22 / 60

23 IntesisBx KNX Hisense The Status_ bject will always return the value fr the fan speed selected. Imprtant: If a 0 value is sent t the Cntrl_ bject, the minimum fan speed will be selected. If a value bigger than 4 is sent t the Cntrl_ bject, then the maximum fan speed will be selected. When Scaling [DPT 5.001] is selected, Cntrl_ Fan Speed and Status_ Fan Speed cmmunicatin bjects fr this DPT will appear The next table shws the range f values that can be sent thrugh the Cntrl_ bject and the value returned by the Status_ bject. Fan Speed 1 Fan Speed 2 Fan Speed 3 Fan Speed 4 Cntrl_ 0% - 49% 50% - 82% 83% - 100% Status_ 33% 67% 100% Cntrl_ 0% - 37% 38% - 62% 63% - 87% 88% - 100% Status_ 25% 50% 75% 100% Imprtant: Read the dcumentatin f yur indr unit t check hw many fan speeds are available Enable use f +/- bject fr Fan Speed This parameter shws/hides the Cntrl_ Fan Speed -/+ cmmunicatin bject which lets increase/decrease the indr unit fan speed by using tw different datapint types. 17 If set t n the bject will nt be shwn. If set t yes the Cntrl_ Fan Speed -/+ bject and a new parameter will appear. Figure 4.15 Parameter detail DPT type fr +/- Fan Speed bject Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 23 / 60

24 IntesisBx KNX Hisense This parameter lets chse between the datapints 0-Up / 1-Dwn [DPT_1.008] and 0-Decrease / 1-Increase [DPT_1.007] fr the Cntrl_ Fan Speed -/+ bject. Rll-ver Speed at upper/lwer limit This parameter lets chse if rll-ver will be enabled ( yes ) r disabled ( n ) fr the Cntrl_ Fan Speed -/+ bject. Only if Rll-ver is enabled FS 1 FS 2 FS 3 FS 4* Only if Rll-ver is enabled Up / Increase Dwn / Decrease * If Available Enable use f bit-type Fan Speed bjects (fr Cntrl) This parameter shws/hides the bit-type Cntrl_ Fan Speed bjects If set t n the bjects will nt be shwn. If set t yes the Cntrl_ Fan Speed bjects fr Speed 1, Speed 2, Speed 3 and Speed 4 (if available) will appear. T activate a Fan Speed by using these bjects a 1 value has t be sent Enable use f bit-type Fan Speed bjects (fr Status) This parameter shws/hides the bit-type Status_ Fan Speed bjects If set t n the bjects will nt be shwn. If set t yes the Status_ Fan Speed bjects fr Speed 1, Speed 2, Speed 3 and Speed 4 (if available) will appear. When a Fan Speed is enabled, a 1 value is returned thrugh its bit-type bject. Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 24 / 60

25 IntesisBx KNX Hisense Enable use f Text bject fr Fan Speed This parameter shws/hides the Status_ Fan Speed Text cmmunicatin bject. 72 If set t n the bject will nt be shwn. If set t yes the Status_ Fan Speed Text bject will appear. Als, in the parameters, will be shwn fur text fields, ne fr each Fan Speed, that will let mdify the text string displayed by the Status_ Fan Speed Text when changing a fan speed. Figure 4.16 Parameter detail 4.5 Vanes Up-Dwn Cnfiguratin dialg Figure 4.17 Vanes Up-Dwn Cnfiguratin dialg All the parameters in this sectin are related with the Vanes Up-Dwn prperties and cmmunicatin bjects Indr unit has U-D Vanes Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 25 / 60

26 IntesisBx KNX Hisense This parameter lets chse if the unit has Up-Dwn Vanes available r nt. Figure 4.18 Parameter detail If set t n all the parameters and cmmunicatin bjects fr the Up-Dwn Vanes will nt be shwn. If set t yes all the parameters and cmmunicatin bjects (if enabled in the parameters dialg) fr the Up-Dwn Vanes will be shwn. Imprtant: Read the dcumentatin f yur indr unit t check if Up-Dwn Vanes are available Available psitins in Indr Unit This parameter lets select the number f vane psitins available in yur indr unit, frm 5 t 7. Figure 4.19 Parameter detail Number f Vane Psitins cnfigured here will have effect n the pssible values in Cntrl_ and Status_ bjects fr Vanes. Imprtant: Read the dcumentatin f yur indr unit t check hw many psitins f Up-Dwn Vanes are available DPT bject type fr Vanes Up-Dwn With this parameter is pssible t change the DPT fr the Cntrl_ Vanes U-D and Status_ Vanes U-D byte-type cmmunicatin bjects. Datapints Scaling (DPT_5.001) and Enumerated (DPT_5.010) can be selected. Imprtant: The cmmunicatin bjects shwn in this sectin may be different depending n the number f vanes psitin available, althugh they all share the same cmmunicatin bject number. When Enumerated [DPT 5.010] is selected, Cntrl_ Vanes U-D and Status_ Vanes U-D cmmunicatin bjects fr this DPT will appear Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 26 / 60

27 IntesisBx KNX Hisense T chse a vanes psitin, values frm 1 t 7 can be sent t the Cntrl_ bject. Each value will crrespnd t the psitin (i.e. Value 3 = Psitin 3). The Status_ bject will always return the value fr the vane psitin selected. Imprtant: If a 0 value is sent t the Cntrl_ bject, the Psitin 1 will be selected. If a value bigger than 7 is sent t the Cntrl_ bject, then the higher Psitin will be selected. When Scaling [DPT 5.001] is selected, Cntrl_ Vanes U-D and Status_ Vanes U-D cmmunicatin bjects fr this DPT will appear The next table shws the range f values that can be sent thrugh the Cntrl_ bject and the value returned by the Status_ bject. Cntrl_ Vanes Ps.1 0% - 29% Vanes Ps.2 30% - 49% Vanes Ps.3 50% - 69% Vanes Ps.4 70% - 89% Vanes Ps.5 90% - 100% Status_ 20% 40% 60% 80% 100% Cntrl_ 0% - 24% 25% - 41% 42% - 58% 59% - 74% 75% - 91% Vanes Ps.6 92% - 100% Status_ 16% 33% 50% 67% 83% 100% Cntrl_ 0% - 20% 21% - 35% 36% - 49% 50% - 64% 65% - 78% 79% - 92% Vanes Ps.7 93% - 100% Status_ 14% 28% 43% 57% 71% 85% 100% Enable use f +/- bject fr Vanes U-D This parameter shws/hides the Cntrl_ Vanes U-D -/+ cmmunicatin bject which lets change the indr unit vane psitin by using tw different datapint types. 27 If set t n the bject will nt be shwn. If set t yes the Cntrl_ Vanes U-D -/+ bject and a new parameter will appear. Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 27 / 60

28 IntesisBx KNX Hisense Figure 4.20 Parameter detail DPT type fr +/- Vanes U-D bject This parameter lets chse between the datapints 0-Up / 1-Dwn [DPT_1.008] and 0-Decrease / 1-Increase [DPT_1.007] fr the Cntrl_ Vanes U-D -/+ bject. Des +/- sequence include SWING vanes Up-Dwn? This parameter lets chse if SWING functin is included ( yes ) r nt ( n ) in the sequence when using Cntrl_ Vanes U-D -/+ bject as shwn in the discntinuus segment at the picture belw. Rll ver Vanes at upper/lwer limit This parameter lets chse if rll-ver will be enabled ( yes ) r disabled ( n ) fr the Cntrl_ Vanes U-D -/+ bject. Only if Rll-ver is enabled P. 1 P. 2 P. 3 P. 4 P. 5 P. 6* P. 7* SW* Only if Rll-ver is enabled Up / Increase Dwn / Decrease * If Available Enable use f bit-type Vane U-D bjects (fr Cntrl) This parameter shws/hides the bit-type Cntrl_ Vanes U-D bjects If set t n the bjects will nt be shwn. If set t yes the Cntrl_ Vanes U-D bjects fr each Psitin will appear. T activate a Vanes Psitin by using these bjects, a 1 value has t be sent Enable use f bit-type Vane U-D bjects (fr Status) Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 28 / 60

29 IntesisBx KNX Hisense This parameter shws/hides the bit-type Status_ Vanes U-D bjects If set t n the bjects will nt be shwn. If set t yes the Status_ Vanes U-D bjects fr each Psitin will appear. When a Vanes Psitin is enabled, a 1 value is returned thrugh its bit-type bject Enable Vanes U-D Swing bjects (fr Cntrl and Status) This parameter shws/hides the Cntrl_ Vanes U-D Swing and Status_ Vanes U-D Swing cmmunicatin bjects If set t n the bjects will nt be shwn. If set t yes the Cntrl_ Vanes U-D Swing and Status_ Vanes U-D Swing bjects will appear. When a 1 value is sent t the Cntrl_ cmmunicatin bject, Vanes Up- Dwn will be in Swing mde, and the Status_ bject will return this value. When a 0 value is sent t the Cntrl_ cmmunicatin bject, Vanes Up- Dwn will stp Swing mde. The Status_ bject will return this value Enable use f Text bject fr Vane U-D This parameter shws/hides the Status_ Vanes U-D Text cmmunicatin bject. 82 If set t n the bject will nt be shwn. If set t yes the Status_ Vanes U-D Text bject will appear. Als, in the parameters will be shwn five text fields, fur fr the Vane Psitin and ne fr the Swing functin that will let mdify the text string displayed by the Status_ Vanes U-D Text when changing a vane psitin. Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 29 / 60

30 IntesisBx KNX Hisense 4.6 Temperature Cnfiguratin dialg Figure 4.21 Parameter detail Figure 4.22 Default Temperature Cnfiguratin dialg All the parameters in this sectin are related with the Temperature prperties and cmmunicatin bjects Peridic sending f Status_ AC Setp This parameter lets change the interval f time (in secnds, frm 0 t 255) at the end f which the AC setpint temperature is sent t the KNX bus. Fr a 0 value, the AC setpint temperature will ONLY be sent n change. The AC setpint temperature is sent thrugh the cmmunicatin bject Status_ AC Setpint Temp. 83 Figure 4.23 Parameter detail Imprtant: In case the ambient temperature is prvided frm KNX, the setpint temperature returned frm this bject, will be the ne resulting frm the frmula shwn in the sectin Ambient temp. ref. is prvided frm KNX. Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 30 / 60

31 IntesisBx KNX Hisense Transmissin f Status_ AC Reference Temp This parameter lets t yu chse if the AC return temperature will be sent nly cyclically, nly n change r cyclically and n change. The AC reference temperature is sent thrugh the cmmunicatin bject Status_ AC Reference Temp. 84 Figure 4.24 Parameter detail Status_ AC Reference Temp peridic sending time (in sec) This parameter will nly be available fr the nly cyclically and cyclically and n change ptins, and let s yu change the interval f time (in secnds, frm 1 t 255) at the end f which the AC return temperature is sent t the KNX bus Enable use f +/- bject fr Setpint Temp This parameter shws/hides the Cntrl_ Setpint Temp -/+ cmmunicatin bject which lets change the indr unit setpint temperature by using tw different datapint types. 29 If set t n the bject will nt be shwn. If set t yes the Cntrl_ Setpint Temp -/+ bject and a new parameter will appear. Figure 4.25 Parameter detail DPT type fr +/- Setp Temp bject This parameter lets chse between the datapints 0-Up / 1-Dwn [DPT_1.008] and 0-Decrease / 1-Increase [DPT_1.007] fr the Cntrl_ Setpint Temp -/+ bject. (Lwer limit) 20ºC 21ºC 29ºC 30ºC (Upper limit) Enable limits n Cntrl_ Setpint bj Up / Increase Dwn / Decrease Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 31 / 60

32 IntesisBx KNX Hisense This parameter enables t define temperature limits fr the Cntrl_ Setpint Temperature bject. Figure 4.26 Parameter detail If set t n the setpint temperature limits fr the Cntrl_ Setpint Temperature bject will be the default: 18ºC fr the lwer limit and 30ºC fr the upper limit. If set t yes it is pssible t define temperature limits fr the Cntrl_ Setpint Temperature bject. Lwer limit (ºC) This parameter lets t define the lwer limit fr the setpint temperature. Upper limit (ºC) This parameter lets t define the upper limit fr the setpint temperature. Imprtant: If a setpint temperature abve the upper defined limit (r belw the lwer defined limit) is sent thrugh the Cntrl_ Setpint Temperature bject, it will be ALWAYS applied the limit defined. Imprtant: When limits are enabled, any setpint temperature sent t the AC (even thrugh scenes, special mdes, etc.) will be limited Ambient temp. ref. is prvided frm KNX This parameter shws/hides the Cntrl_ Ambient Temperature cmmunicatin bject which lets use an ambient temperature reference prvided by a KNX device. 30 If set t n the bject will nt be shwn. If set t yes the Cntrl_ Ambient Temperature bject will appear. Meant t be enabled when yu want the temperature prvided by a KNX sensr t be the reference ambient temperature fr the air cnditiner. Then, the fllwing frmula applies fr calculatin f real Cntrl_ Setpint Temperature sent t the AC unit: AC Setp. Temp = AC Ret. Temp - ( KNX Amb. Temp. - KNX Setp. Temp ) AC Setp. Temp: AC indr unit setpint temperature AC Ret. Temp: AC indr unit return temperature KNX Amb. Temp.: Ambient temperature prvided frm KNX KNX Setp. Temp: Setpint temperature prvided frm KNX Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 32 / 60

33 IntesisBx KNX Hisense As an example, cnsider the fllwing situatin: User wants: 19ºC ( KNX Setp. Temp. ) User sensr (a KNX sensr) reads: 21ºC ( KNX Amb Temp. ) Ambient temp. read by HISENSE system is: 24ºC ( AC Ret. Temp ) In this example, the final setpint temperature that HS-RC-KNX-1i will send ut t the indr unit (shwn in Setp. Temp. ) will becme 24ºC (21ºC - 19ºC) = 22ºC. This is the setpint that will actually be requested t HISENSE unit. This frmula will be applied as sn as the Cntrl_ Setpint Temperature and Cntrl_ Ambient Temperature bjects are written at least nce frm the KNX installatin. After that, they are kept always cnsistent. Nte that this frmula will always drive the AC indr unit demand in the right directin, regardless f the peratin mde (Heat, Cl r Aut). 4.7 Scene Cnfiguratin dialg Figure 4.27 Parameter detail All the parameters in this sectin are related with the Scene prperties and cmmunicatin bjects. A scene cntains values f: On/Off, Mde, Fan speed, Vane psitin, Setpint Temperature and Remte Cntrller Disablement Enable use f scenes This parameter shws/hides the scene cnfiguratin parameters and cmmunicatin bjects. 42 Figure 4.28 Parameter detail If set t n the scene parameters and cmmunicatin bjects will nt be shwn. Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 33 / 60

34 IntesisBx KNX Hisense If set t yes the scene parameters and cmmunicatin bjects will be shwn. T execute a scene thrugh the byte-type bject, a value frm 0 t 4 has t be sent, crrepnding each ne t a different scene (i.e. 0 = Scene 1; 4 = Scene 5) Scenes can be stred frm KNX bus This parameter shws/hides the Cntrl_ Save/Exec Scene and all the Cntrl_ Stre Scene (if enabled) cmmunicatin bjects If set t n the cmmunicatin bjects will nt be shwn. If set t yes the cmmunicatin bjects and a new parameter will appear. T stre a scene thrugh the byte-type bject, a value frm 128 t 132 has t be sent t the bject, crrepnding each ne t a different scene (i.e. 128 = Scene 1; 132 = Scene 5). Figure 4.29 Parameter detail Enable use f bit bjects fr string scenes (frm bus) If set t n the bjects will nt be shwn. If set t yes the Cntrl_ Stre Scene bjects fr string scenes will appear. T stre a scene by using these bjects, a 1 value has t be sent t the scene s bject we want t stre (i.e. t stre scene 4, a 1 has t be sent t the Cntrl_ Stre Scene 4 bject) Enable use f bit bjects fr scene executin This parameter shws/hides the Cntrl_ Execute Scene bit-type cmmunicatin bjects Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 34 / 60

35 IntesisBx KNX Hisense Figure 4.30 Parameter detail If set t n the cmmunicatin bjects will nt be shwn. If set t yes the cmmunicatin bjects will appear. T execute a scene by using these bjects, a 1 value has t be sent t the scene s bject we want t execute (i.e. t execute scene 4, a 1 has t be sent t the Cntrl_ Execute Scene 4 bject) Scene x preset This parameter lets define a preset fr a scene (the fllwing descriptin is valid fr all the scenes). Figure 4.31 Parameter detail If set t n the preset fr the scene x will be disabled. If set t yes the preset will be enabled. When a scene is executed the values cnfigured in the preset will be aplied. Imprtant: If a scene s preset is enabled, will nt be pssible t mdify (stre) the scene frm the KNX bus. Figure 4.32 Parameter detail Scene x / Value fr On-Off This parameter lets chse the pwer f the indr unit when the scene is executed. The fllwing ptins are available: ON, OFF r (unchanged). Scene x / Value fr Mde This parameter lets chse the mde f the indr unit when the scene is executed. The fllwing ptins are available: AUTO (if available), HEAT, COOL, FAN, DRY, r (unchanged). Scene x / Value fr Fan Speed (if available) This parameter lets chse the fan speed f the indr unit when the scene is executed. The fllwing ptins are available: FAN SPEED 1, FAN SPEED 2 (if Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 35 / 60

36 IntesisBx KNX Hisense available), FAN SPEED 3 (if available), FAN SPEED 4 (if available), r (unchanged). Scene x / Value fr Vanes U-D (if available) This parameter lets chse the vane psitin f the indr unit when the scene is executed. The fllwing ptins are available: VANES U-D POS 1, VANES U-D POS 2, VANES U-D POS 3, VANES U-D POS 4, VANES U-D SWING r (unchanged). Scene x / Value fr Setp Temp (ºC) This parameter lets chse the setpint temperature f the indr unit when the scene is executed. The fllwing ptins are available: frm 18ºC t 30ºC (bth included), r (unchanged). Scene x / Value fr Remte Lck This parameter lets chse the remte cntrller status f the indr unit when the scene is executed. The fllwing ptins are available: lcked, unlcked, r (unchanged). Imprtant: If any preset value is cnfigured as (unchanged), the executin f this scene will nt change current status f this feature in the AC unit. Imprtant: When a scene is executed, Status_ Current Scene bject shws the number f this scene. Any change in previus items des Status_ Current Scene shw N Scene. Only changes n items marked as (unchanged) will nt disable current scene. 4.8 Switch-Off Timeuts Cnfiguratin dialg Figure 4.33 Default Switch-Off Timeuts Cnfiguratin dialg All the parameters in this sectin are related with the timeut prperties and cmmunicatin bjects. Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 36 / 60

37 IntesisBx KNX Hisense Enable use f Open Windw / Switch ff timeut functin This parameter shws/hides the Cntrl_ Windw Cntact Status cmmunicatin bject which lets Start/Stp a timeut t switch ff the indr unit. 33 If set t n the bject will nt be shwn. If set t yes the Cntrl_ Windw Cntact Status bject and new parameters will appear. If a 1 value is sent t this bject, and the indr unit is already turned n, the switch-ff timeut will begin. If a 0 value is sent t this bject, the switch-ff timeut will stp. Figure 4.34 Parameter detail AC switch-ff timeut (min) This parameter lets select hw much time (in minutes) t wait befre switching ff the indr unit. DPT fr Windw This parameter lets chse between the datapints 0-Open / 1-Clsed Windw [DPT_1.009] and 0-Clsed / 1-Open Windw [DPT_1.019]. Disallw On/Off peratin while windw is Open If set t n, On/Off cmmands while the windw is pen will be accepted. If a 1 value is sent t the Cntrl_ Switch Off Timeut bject the switch-ff timeut perid will begin again. If a 0 value is sent t the Cntrl_ Switch Off Timeut bject, n actin will be perfrmed. If set t yes, On/Off cmmands, while the windw is pen, will be saved (but nt applied). These cmmands will be used in the next parameter if set t yes. Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 37 / 60

38 IntesisBx KNX Hisense Relad last On/Off value nce windw is clsed? If set t n, nce the switch-ff timeut is stpped, any value will be reladed. If set t yes, nce the switch-ff timeut is stpped, the last On/Off value sent will be reladed. If a 1 value is sent t the Cntrl_ Switch Off Timeut bject after the timeut perid, the indr unit will turn n. If a 0 value is sent t the Cntrl_ Switch Off Timeut after the timeut perid, n actin will be perfrmed Enable use f Occupancy functin This parameter shws/hides the Cntrl_ Occupancy cmmunicatin bject which lets apply different parameters t the indr unit depending n the presence/n presence in the rm. 34 If set t n the bject will nt be shwn. If set t yes the Cntrl_ Occupancy bject and new parameters will appear. If a 1 value is sent t this bject (n rm ccupancy), the timeut will begin. If a 0 value is sent t this bject, the timeut will stp. Timeut t apply actin (minutes) Figure 4.35 Parameter detail This parameter lets chse hw much time t wait (in minutes) befre executing the actin specified in the next parameter ( Actin after timeut elapsed ). Actin after timeut elapsed When Switch-Off is selected, nce the timeut has elapsed, the indr unit will be turned ff. When Apply Preset Delta is selected, nce the timeut has elapsed, a delta temperature will be applied in rder t save energy (decreasing the setpint when in Heat mde, r increasing the setpint when in Cl mde). Als new parameters will appear. Figure 4.36 Parameter detail Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 38 / 60

39 IntesisBx KNX Hisense Temp delta decrease (HEAT) r increase (COOL) (ºC) This parameter lets cnfigure the delta temperature (increase r decrease) that will be applied when the timeut has elapsed. Imprtant: When there is ccupancy again after the applicatin f a delta, the same delta will be applied inversely. (i.e. In a rm with AC in cl mde and 25ºC setpint temperature, a +2ºC delta is applied after the ccupancy timeut, setting the setpint at 27ºC because there is n ccupancy in the rm. If the setpint is raised t 29ºC during that perid, when the rm is ccupied again, a -2ºC delta will be applied and the final setpint temperature will then be 27ºC). Enable secndary timeut If set t n nthing will be applied. If set t yes, a new timeut will be enabled and tw new parameters will appear. Figure 4.37 Parameter detail Timeut t apply actin (minutes) This parameter lets chse hw much time t wait (in minutes) befre executing the actin specified in the next parameter ( Actin after timeut elapsed ). Actin after timeut elapsed When Switch-Off is selected, nce the timeut has elapsed, the indr unit will turn ff. When Apply Preset Delta is selected, nce the timeut cnfigured is extinguished, a delta temperature will be applied (decreasing the setpint when in Heat mde, r increasing the setpint when in Cl mde). Als new parameters will appear. Temp delta decrease (HEAT) r increase (COOL) (ºC) This parameter lets cnfigure the delta temperature that will be applied when the timeut is extinguished. Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 39 / 60

40 IntesisBx KNX Hisense Imprtant: When there is ccupancy again after the applicatin f a delta, the same delta will be applied inversely as explained abve. Disallw On/Off peratin while nt Occupied If set t n, On/Off cmmands while the windw is pen will be accepted. If a 1 value is sent t the Cntrl_ Occupancy bject the switch-ff timeut perid will begin again. If a 0 value is sent t the Cntrl_ Occupancy bject, n actin will be perfrmed. If set t yes, On/Off cmmands while nt ccupied will be saved (but nt applied). These cmmands will be used in the next parameter if set t Yes. Figure 4.38 Parameter detail Relad last On/Off value when Occupied If set t n, nce the switch-ff timeut has elapsed, any value will be reladed. If set t yes, nce the switch-ff timeut has elapsed, the last On/Off value will be reladed. If a 1 value is sent t the Cntrl_ Occupancy bject after the timeut perid, the indr unit will turn n. If a 0 value is sent t the Cntrl_ Occupancy after the timeut perid, n actin will be perfrmed Enable use f SLEEP timeut This parameter shws/hides the Cntrl_ Sleep Timeut cmmunicatin bject which lets start a timeut t autmatically turn ff the indr unit. 35 If set t n the bject will nt be shwn. If set t yes the Cntrl_ Sleep Timeut bject and a new parameter will appear. If a 1 value is sent t this bject the switch-ff timeut will begin. If a 0 value is sent t this bject, the switch-ff timeut will stp. Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 40 / 60

41 IntesisBx KNX Hisense Figure 4.39 Parameter detail Sleep functin switch-ff timeut (minutes) This parameter lets select hw much time (in minutes) t wait befre switching ff the AC unit. 4.9 Binary Input x Cnfiguratin dialg Figure 4.40 Binary Input Cnfiguratin dialg All the parameters in this sectin are related with the binary inputs prperties and cmmunicatin bjects Enable use f Input x This parameter enables the use f the Input x and shws/hides the Status_ Inx cmmunicatin bject(s) which will act as cnfigured in the Functin parameter If set t n the bjects will nt be shwn. If set t yes the Status_ Inx bject(s) and new parameters will appear Cntact type Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 41 / 60

42 IntesisBx KNX Hisense This parameter lets chse the behavir that will have the binary input depending n if the cntact is nrmally pen r nrmally clsed. There are tw pssible ptins t cnfigure the cntact type: NO: Nrmally Open and NC: Nrmally Clsed Debunce time This parameter lets chse a debunce time (in millisecnds) that will be applied t the cntact Disabling functin This parameter shws/hides the Cntrl_ Disable Input x cmmunicatin bject which will let disable/enable the input x If set t n any bject will be shwn. When DPT 1.003: 0-Disable; 1-Enable is selected, the input can be disabled using the value 0 and enabled using the value 1. When DPT 1.002: 1-True (Disable); 0-False (Enable) is selected, the input can be disabled using the value 1 and enabled using the value Functin This parameter lets chse the functin that will have the binary input. There are 7 different functins available: Switching, Dimming, Shutter/Blind, Value, Execute Scene (internal), Occupancy (internal) and Windw Cntact (internal). When Switching is selected the cmmunicatin bject and new parameters fr the Input x will appear as shwn belw. 99 Figure 4.41 Parameter detail Send egram after bus recvery Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 42 / 60

43 IntesisBx KNX Hisense This parameter lets select if the Binary Input x will send a egram, r nt, after a bus recvery, and the type f egram sent (if enabled). When N actin is selected, n egram will be sent after a bus recvery. When Current status is selected, the binary input will send a egram with its current status after a bus recvery. Als a new parameter will appear (see belw). When On is selected, the binary input will send a egram with a 1 value after a bus recvery. Als a new parameter will appear (see belw). When Off is selected, the binary input will send a egram with a 0 value after a bus recvery. Als a new parameter will appear (see belw). Figure 4.42 Parameter detail Sending delay after a bus recvery (secnds) This parameter lets cnfigure a delay (in secnds) that will be applied after a bus recvery and, after which, a egram will be sent. Value n rising edge This parameter lets select the value that the Binary Input x will send n a rising edge (cntact activated). When On is selected, the binary input will always send egrams with a 1 value. When Off is selected, the binary input will always send egrams with a 0 value. When Tggle (On/Off) is selected, the binary input will send a 1 value after a 0 value and viceversa. When N actin is selected, the binary input will nt perfrm any actin. Value n falling edge This parameter lets select the value that the Binary Input x will send n a falling edge (cntact deactivated). When On is selected, the binary input will always send egrams with a 1 value. Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 43 / 60

44 IntesisBx KNX Hisense When Off is selected, the binary input will always send egrams with a 0 value. When Tggle (On/Off) is selected, the binary input will send a 1 value after a 0 value and viceversa. When N actin is selected, the binary input will nt perfrm any actin. Cyclical sending This parameter lets enable/disable cyclical sending when a determined cnditin is met. When When utput value is On is selected, everytime a 1 value is sent, it will be sent cyclically. Als a new parameter will appear (see belw). When When utput value is Off is selected, everytime a 0 value is sent, it will be sent cyclically. Als a new parameter will appear (see belw). When Always is selected, the binary input will send any value cyclically. Als a new parameter will appear (see belw). When Never is selected, cyclical sending will be disabled. Perid fr cyclical sending (secnds) This parameter lets cnfigure a time (in secnds) fr the cyclical sending. Figure 4.43 Parameter detail When Dimming is selected the cmmunicatin bjects and new parameters fr the Input x will appear as shwn belw Figure 4.44 Parameter detail Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 44 / 60

45 IntesisBx KNX Hisense Send egram after bus recvery This parameter lets select if the Binary Input x will send a egram, r nt, after a bus recvery, and the type f egram sent (if enabled). When N actin is selected, n egram will be sent after a bus recvery. When On is selected, the binary input will send a egram with a 1 value after a bus recvery. Als a new parameter will appear (see belw). When Off is selected, the binary input will send a egram with a 0 value after a bus recvery. Als a new parameter will appear (see belw). Figure 4.45 Parameter detail Sending delay after a bus recvery (secnds) This parameter lets cnfigure a delay (in secnds) that will be applied after a bus recvery and, after which, a egram will be sent. Mde fr shrt (lng) peratin This parameter lets select the value that the Binary Input x will send n a rising edge (cntact activated), fr a shrt and a lng peratin. When On (increase) is selected, the binary input will always send egrams with a 1 value fr a shrt peratin, and an increase step fr a lng peratin. When Off (decrease) is selected, the binary input will always send egrams with a 0 value fr a shrt peratin, and an decrease step fr a lng peratin. When Tggle: On/Off (increase/decrease) is selected: Fr the shrt peratin the binary input will send a 1 value after a 0 value and viceversa. Fr the lng peratin the binary input will send an increase step after a decrease step and viceversa. Imprtant: Nte that the first lng peratin in tggle depends n the last shrt peratin, meaning that after a 1 value will be sent a decrease step and after a 0 value will be sent an increase step. Imprtant: The time perid between a shrt and a lng peratin is defined in the parameter Shrt/lng peratin limit (x100ms). Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 45 / 60

46 IntesisBx KNX Hisense Increasing step This parameter lets select the increasing step value (in %) that will be sent fr a lng peratin. Decreasing step This parameter lets select the decreasing step value (in %) that will be sent fr a lng peratin. Shrt/lng peratin limit (x100ms) This parameter lets intrduce the time perid difference fr the shrt and the lng peratin. Cycl. send. perid in lng per. (x100ms) This parameter lets cnfigure a time (in secnds) fr the cyclical sending f a lng peratin. When Shutter/Blind is selected the cmmunicatin bjects and new parameters fr the Input x will appear as shwn belw Figure 4.46 Parameter detail Send egram after bus recvery This parameter lets select if the Binary Input x will send a egram, r nt, after a bus recvery and the type f egram sent (if enabled). When N actin is selected, n egram will be sent after a bus recvery. When Mve Up is selected, the binary input will send a egram with a 0 value after a bus recvery. Als a new parameter will appear (see belw). When Mve Dwn is selected, the binary input will send a egram with a 1 value after a bus recvery. Als a new parameter will appear (see belw). Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 46 / 60

47 IntesisBx KNX Hisense Figure 4.45 Parameter detail Sending delay after a bus recvery (secnds) This parameter lets cnfigure a delay (in secnds) that will be applied after a bus recvery and, after which, a egram will be sent. Operatin This parameter lets select the value that the Binary Input x will send n a rising edge (cntact activated). When Up is selected, the binary input will always send egrams with a 0. When Dwn is selected, the binary input will always send egrams with a 1 value. When Tggle (Up/Dwn) is selected the binary input will send a 0 value after a 1 value and viceversa. Methd This parameter lets select the wrking methd fr the shutter/blind. When Step-Mve-Step is selected: On a rising edge (cntact activated) a step/stp egram will be sent and will begin a time called T1. If a falling edge ccurs (cntact deactivated) during the T1, n actin will be perfrmed. If the rising edge is maintained lnger than T1, a mve egram will be sent and will start a time called T2. If a falling edge ccurs during the T2, a step/stp egram will be sent. If a falling edge ccurs after T2 n actin will be perfrmed. When Mve-Step is selected: On a rising edge a mve egram will be sent and will begin the T2 time. If a falling edge ccurs during the T2, a step/stp egram will be sent. If a falling edge ccurs after T2 n actin will be perfrmed. Imprtant: The T1 time have t be defined in the Shrt/lng peratin limit (x100ms) parameter. The T2 time has t be defined in the Vanes adjustment time (x100ms) parameter t. Shrt/lng peratin limit (x100ms) This parameter lets intrduce the time perid difference fr the shrt and the lng peratin (T1 time). Vanes adjustment time (x100ms) Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 47 / 60

48 IntesisBx KNX Hisense This parameter lets intrduce the time perid fr the vanes adjustment/blind mvement (T2 time). When Value is selected the cmmunicatin bjects and new parameters fr the Input x will appear as shwn belw. 106 Figure 4.46 Parameter detail Send egram after bus recvery This parameter lets select if the Binary Input x will send a egram, r nt, after a bus recvery and the type f egram sent (if enabled). When N actin is selected, n egram will be sent after a bus recvery. When Fixed value is selected, the binary input will send a egram with the same value cnfigured in the Value n rising edge parameter. Als a new parameter will appear (see belw). Figure 4.47 Parameter detail Sending delay after a bus recvery (secnds) This parameter lets cnfigure a delay (in secnds) that will be applied after a bus recvery and, after which, a egram will be sent. DPT t be sent This parameter lets select the DPT type fr the value that will be defined in the next parameter. This value will be sent n a rising edge (cntact activated). Figure 4.48 Parameter detail Value n rising edge (when cntact activated) Intesis Sftware SLU - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU inf@intesisbx.cm 48 / 60