Vortex Flow Measuring System PROline prowirl 72

Transcription

1 Technical Information TI 062D/06/en No Vortex Flow Measuring System PROline prowirl 72 Reliable Flow Measurement of Gas, Steam and Liquids pplication For measuring the volume flow of steam, gases and liquids. For utility and process applications in the chemical, petrochemical, power and district heating industries and in many other branches. Your benefits Proven capacitive sensor (installed base > 100,000) Immune to: Vibrations (over 1 g in all axes) Temperature shocks (> 150 K/s) Dirty media Water hammer Process temp. range C Universal: Compact or remote version Dualsens version, with two sensors and electronics (for redundancy) lloy C-22 version Connection to all common systems: HRT PROFIUS-P FOUNDTION Fieldbus Galvanically isolated pulse output available (for alarm, limit value etc.). Permanent self-monitoring and diagnosis of electronics and sensor. Correction of diameter mismatch. No maintenance, no moving parts, no zero-point drift.

2 Function and system design Measuring principle Vortex shedding flowmeters work on the principle of the Karman vortex street. When a fluid flows past a bluff body, vortices are alternately formed and shed on both sides with opposite senses of rotation. These vortices each generate a local low pressure. The pressure fluctuations are recorded by the sensor and converted to electrical pulses. The vortices develop very regularly within the application limits of the device. Therefore, the frequency of vortex shedding is directly proportional to the volume flow. v F06-7xxxxxxx-15-xx-06-xx-000 The K-factor is used as the proportional constant: K-Factor = pulses unit volume [dm³] F06-7xxxxxxx-19-xx-06-en-000 Within the application limits of the device, the K-factor only depends on the geometry of the device. It is independent of the fluid velocity and its properties viscosity and density. In this way, the K-factor is also independent of the type of fluid to be measured, regardless of whether this is steam, a gas or a liquid. The primary measuring signal is already digital (frequency signal) and a linear function of the flow. fter manufacturing the meter, the K-factor is determined once-off in the factory by means of calibration and is not subjected to any long term drift or zero point shift. The device does not contain any moving parts and requires no maintenance. The capacitive sensor The sensor of a vortex flowmeter has a major influence on the performance, robustness and reliability of the whole measuring system. Prowirl 72 uses ndress + Hauser's proven and patented capacitive measuring technology, with to date more than 100,000 Vortex measuring points installed world wide. Due to its internal mechanical balance, the DSC sensor (Differential Switched Capacitance), reads only the pressure pulses caused by the vortices and stays immune to any influence from mechanical pipe line vibrations. The DSC sensor measures low flow rates at low fluid density even when pipe line vibrations are present. Therefore, Prowirl 72 keeps its wide turndown ratio even under rough operating conditions. Vibrations of at least 1g at frequencies up to 500 Hz in all axes do not affect the flow measurement. Thanks to its mechanical design, the capacitive sensor is also especially resistant to temperature shocks and water hammer in steam lines. Z-xis Sensor Seal Y-xis X-xis F06-7xxxxxxx en ndress + Hauser

3 Measuring system The measuring system consist of a sensor and a transmitter. Two versions are available: Compact version: sensor and transmitter form a mechanical unit. Remote version: sensor is mounted separate from the transmitter. Sensor Prowirl F (DN ) Flanged version (also available as version with two sensors and electronics for redundancy, DN ) Prowirl W (DN ) Wafer version Transmitter Prowirl 72 Input Measured variable Measuring range Volumetric flow (volume flow), is proportional to the frequency of vortex shedding after the bluff body. The output variables are volume flow or, if the process conditions are non-varying, calculated mass flow or corrected volume flow. The measuring range depends on the fluid and the nominal diameter. Start of measuring range: Depends on the density and the Reynolds number (Re min = 4000 Re linear = 20000) DN v min. = 6 [kg/m³] [m/s] DN v min. = 7 [kg/m³] [m/s] F06-72xxxxxx-19-xx-06-xx-002.eps Full scale value: Gas/steam: v max = 75 m/s (DN 15: v max = 46 m/s) Liquids: v max = 9 m/s Note! y using the selection and sizing software "pplicator", you can determine the exact values for the fluid you use. You can obtain pplicator from your ndress+hauser sales centre or on the Internet at Measuring range for gases [m³/h or Nm³/h] In the case of gases, the start of the measuring range depends on the density. With ideal gases, the density [ρ] or corrected density [ρ N ] can be calculated using the following formulae: [kg/m³] = N [kg/nm³] P [bar abs] [K] T [K] [bar abs] N [kg/nm³] = [kg/m³] T [K] [bar abs] P [bar abs] [K] F06-7xxxxxxx-19-xx-xx-en-002 The following formulae can be used to calculate the volume [Q] or corrected volume [Q N ] in the case of ideal gases: Q[m³/h] = Q [Nm³/h] T [K] [bar abs] N P [bar abs] [K] [Nm³/h] = Q N Q [m³/h] P [bar abs] [K] T [K] [bar abs] F06-7xxxxxxx-19-xx-xx-en-003 T = Operating temperature P = Operating pressure ndress + Hauser 3

4 Output Output signal Current output: m with HRT, Full scale value and time constant ( s) can be set Temperature coefficient: typically 0.005% o.r. / C (o.r. = of reading) Pulse/status output: Open collector, passive, Galvanically isolated, Non-x, x d: U max = 36 V, with 15 m current limit, R i = 500 Ω x i: U max = 30 V, with 15 m current limit, R i = 500 Ω Can be configured as: Pulse output: Pulse value and polarity can be selected ( ms), Pulse frequency max. 100 Hz Status output: Can be configured for error messages or flow limit values Vortex frequency: Direct output of unscaled vortex pulses Hz (pulse ratio 1:1). PFM signal (pulse-frequency modulation): y connecting the pulse and current output. PROFIUS-P interface: PROFIUS-P in accordance with N Volume 2, IC (MP), galvanically isolated Current consumption = 15 m FD (Fault Disconnection lectronic) = 0 m Data transmission rate: Supported baudrate = kit/s Signal encoding = Manchester II Function blocks: 1 x nalog Input, 1 x Totalizer Output data: Volume flow, Calculated mass flow, Corrected volume flow, Totalizer Input data: mpty pipe detection (ON/OFF), Control totalizer us address adjustable via DIP-switches at the measuring device FOUNDTION Fieldbus interface: FOUNDTION Fieldbus H1, IC , galvanically isolated Current consumption available on request Signal encoding = Manchester II FD (Fault Disconnection lectronic) = 0 m Data transmission rate: Supported baudrate = kit/s Function blocks: 2 x nalog Input, 1 x Digital Output, 1 x PID Output data: Volume flow, calculated Mass flow, corrected Volume flow, Totalizer Input data: mpty pipe detection (ON/OFF), Reset totalizer Signal on alarm Current output: error response can be selected (e.g. in accordance with NMUR Recommendation N 43) Pulse output: error response can be selected Status output: not conducting in event of fault 4 ndress + Hauser

5 Load R [ ] R [ ] Non-x x d U [ ] S V R [ ] x i U [ ] S V The load can be calculated as follows: U S UKl U S UKl R = = 3 I 10 0,022 max The grey shaded area indicates the permissible load (for HRT: min. 250 ) R Load US Supply voltage Non-x = V DC, x i = V DC, x d = V DC Imax Output current ( 22,6 m) F06-72xxxxxx-05-xx-xx-en-001 Low flow cut off Galvanic isolation Switch points for low flow cut off can be selected as required The electrical connections are galvanically isolated from one another. ndress + Hauser 5

6 lectrical connection Power supply D C C lectrical connection Prowirl 72 - HRT: Power supply, current output - PROFIUS-P: 1 = P+, 2 = P - FOUNDTION Fieldbus: 1 = FF+, 2 = FF Optional pulse output, can also be operated as status output (except PROFIUS-P and FOUNDTION Fieldbus) C Ground terminal (relevant for remote version) D PFM wiring (pulse-frequency modulation) F06-72xxxxxx xx-000.eps Supply voltage Cable entry Power supply failure Non-x: V DC (with HRT V DC) x i: V DC (with HRT V DC) x d: V DC (with HRT V DC) PROFIUS-P and FOUNDTION Fieldbus Non-x: V DC x i: V DC x d: V DC Current consumption PROFIUS-P: 15 m, FOUNDTION Fieldbus: on request Power supply and signal cables (outputs): Cable entry M20 x 1.5 ( mm) Thread for cable entry: ½" NPT, G ½" (not for remote version) Fieldbus connector Totalizer stops at the last value determined (can be configured) ll settings are kept in the PROM rror messages (incl. value of operated hours counter) are stored Performance characteristics Reference operating conditions Maximum measured error rror limits following ISO/DIN 11631: C, bar, Calibration rig traccable to national standards Calibration with the corresponding process connection of the respective norms Liquid: < 0.75% o.r. for Re > < 0.75% o.f.s for Re between Gas/steam: < 1% o.r. for Re > < 1% o.f.s for Re between o.r. = Of reading, o.f.s = Of full scale, Re = Reynolds number Repeatability ±0.25% o.r. (of reading) 6 ndress + Hauser

7 PROline Prowirl 72 F, W Operating conditions: installation Installation instructions Vortex meters require a fully developed flow profile as a prerequisite for correct volume flow measurement. For this reason, please note the following points when installing the device: Orientation The device can generally be installed in any position in the piping. In the case of liquids, upward flow is prefered in vertical pipes to avoid partial pipe filling (see orientation ). In the case of hot fluids (e.g. steam or fluid temperature 200 C), select orientation C or D so that the permitted ambient temperature of the electronics is not exceeded. Orientations and D are recommended for very cold fluid (e.g. liquid nitrogen). Orientations, C and D are possible with horizontal installation. The arrow indicated on the device must always point in the direction of flow in all mounting orientations. Caution! If fluid temperature is 200 C, orientation is not permitted for the wafer version (Prowirl 72 W) with a nominal diameter of DN 100 and DN 150. C D Possible orientations of the device F06-7xxxxxxx-04-xx-xx-xx-002 Minimum spacing and cable length Please pay attention to the following dimensions when installing in piping: Minimum spacing in all directions = 100 mm () Necessary cable length L mm L Minimum spacing and cable length F06-7xxxxxxx xx-xx-000 ndress + Hauser 7

8 PROline Prowirl 72 F, W Rotating the electronics housing and the display The electronics housing can be rotated continuously 360 on the housing support. The display unit can be rotated in 45 steps. This means you can read off the display comfortably in all orientations. Piping insulation When insulating, please ensure that a sufficiently large area of the housing support is exposed. The uncovered part serves as a radiator and protects the electronics from overheating (or undercooling). The maximum insulation height permitted is illustrated in the diagrams. These apply equally to both the compact version and the sensor in the remote version = Flanged version 2 = Wafer version F06-7xxxxxxx xx-001 Wafer version mounting set The centering rings supplied with the wafer style meters are used to mount and center the instrument. mounting set consisting of tie rods, seals, nuts and washers can be ordered separately Mounting wafer version 1 = Nut 2 = Washer 3 = Tie rod 4 = Centering ring (is supplied with the device) 5 = Seal F06-7xxxxxxx xx ndress + Hauser

9 PROline Prowirl 72 F, W Inlet and outlet run s a minimum, the inlet and outlet runs shown below must be observed to achieve the specific accuracy of the device. The longest inlet and outlet run shown must be observed if two or more flow disturbances are present x DN 5 x DN 2 18 x DN 5 x DN x DN 5 x DN 40 x DN 5 x DN 5 25 x DN 5 x DN 6 50 x DN 5 x DN Minimum inlet and outlet runs with various flow obstructions = Inlet run = Outlet run 1 = Reduction 2 = xtension 3 = 90 elbow or T-piece 4 = 2 x 90 elbow, 3-dimensional 5 = 2 x 90 elbow 6 = Control valve F06-7xxxxxxx-04-xx-xx-xx-000 Note! specially designed perforated plate flow conditioner can be installed if it is not possible to observe the inlet runs required (see Page 10). Outlet runs with pressure and temperature measuring points If pressure and temperature measuring points are installed after the device, please ensure there is a large enough distance between the device and the measuring point so there are no negative effects on the vortex shedding. PT TT x DN x DN PT = Pressure measuring point TT = Temperature measuring point F06-7xxxxxxx-04-xx-xx-xx-003 ndress + Hauser 9

10 PROline Prowirl 72 F, W Perforated plate flow conditioner specially designed perforated plate flow conditioner, available from ndress+hauser, can be installed if it is not possible to observe the inlet runs required. The flow conditioner is fitted between two piping flanges and centered with mounting bolts. Generally, this reduces the inlet run required to 10 x DN with complete accuracy. 2 x DN 8 x DN 5 x DN Flow conditioner F06-7xxxxxxx-04-xx-xx-xx-001 The pressure loss for flow conditioners is calculated as follows: p [mbar] = ρ [kg/m³] v² [m/s] xamples of pressure loss for flow conditioner xample with steam p = 10 bar abs t = 240 C ρ = 4.39 kg/m³ v = 40 m/s p = ² = 59.7 mbar xample with H 2 O condensate (80 C) ρ = 965 kg/m³ v = 2.5 m/s p = ² = 51.3 mbar Operating conditions: environment mbient temperature range Compact version: C Display can be read between 20 C C Remote version: Sensor C Transmitter C Display can be read between 20 C C When mounting outside, protect from direct sunlight with a protective cover (order number ), especially in warmer climates with high ambient temperatures. Storage temperature C Degree of protection IP 67 (NM 4X) according to N Vibration resistance cceleration up to 1 g, Hz, following IC lectromagnetic compatibility (MC) ccording to N 61326/1 and NMUR Recommendation N ndress + Hauser

11 Operating conditions: process Medium temperature range DSC sensor (differential switched capacitor) capacitive sensor: DSC standard sensor C DSC high/low temperature sensor C DSC sensor Inconel (PN , Class 600, C JIS 40K and Dualsens version) DSC sensor lloy C C Seal: Graphite C Viton C Kalrez C Gylon (PTF) C Medium pressure Pressure-temperature curve according to DIN (stainless steel) PN Prowirl 72 W and 72 F PN Prowirl 72 F bar PN 40 PN 25 PN 16 PN PN C bar PN 160 PN 100 PN PN C F06-7xxxxxxx-05-xx-xx-xx-000 Pressure-temperature curve according to NSI 16.5 and JIS 2238 (stainless steel) NSI 16.5: Class Prowirl 72 W and 72 F Class 600 Prowirl 72 F JIS 2238: K Prowirl 72 W and 72 F 40K Prowirl 72 F Class bar Cl Cl Cl C bar 40 K 20 K 10 K K C F06-7xxxxxxx-05-xx-xx-xx-001 Continued on next page. ndress + Hauser 11

12 PROline Prowirl 72 F, W Pressure-temperature curve according to DIN, NSI 16.5 and JIS 2238 (lloy C-22) PN , Class , K Prowirl 72 F bar PN 40 PN Class 300 Class K 10 K C F06-7xxxxxxx-05-xx-xx-xx-002 Pressure loss The pressure loss can be determined with the aid of the pplicator, a software for selection and sizing of flowmeters. The software is available both via Internet ( and on a CD-ROM for local PC installation. Mechanical construction Design, dimensions Dimensions of transmitter, remote version 232 (226)* Ø 8.6 (M8) (163)* 345 (368)* * The following dimensions differ depending on the version: The dimension 232 mm changes to 226 mm in the blind version (without local operation). The dimension 150 mm changes to 163 mm in the x d version. The dimension 345 mm changes to 368 mm in the x d version. F06-72xxxxxx xx-000.eps 12 ndress + Hauser

13 NICHT UNTR SPNNUNG ÖFFNN N IN XPLOSIV TMOSPHR TIGHT W H S WRNUNG VRTISSMNT WRNING LIV PROline Prowirl 72 F, W Dimensions of Prowirl 72 W Wafer version for flanges according to: DIN 2501, PN NSI 16.5, Class , Sch40 JIS 2238, K, Sch (142)* ** ** H H 42.5 d D C 151 (144)* 161 PS OUVRIR OUS TNSION N CIRCUIT KP H + 7 Dimensions: = Standard and x i version = Remote version C = x d version (transmitter) * The following dimensions change as follows in the blind version (without local operation): Standard and x i version: the dimension 149 mm changes to 142 mm in the blind version. x d version: the dimension 151 mm changes to 144 mm in the blind version. ** The dimension depends on the cable gland used. F06-72xxxxxx xx-000 Note! In the following tables, dimension H increases by 29 mm in the version with extended temperature range (high temperature version) and in the version with a DSC sensor made of lloy C-22. The weight data refer to the compact version. The weight increases by 0.5 kg for the version with extended temperature range. DN d D H Weight DIN/JIS NSI [mm] [mm] [mm] [kg] 15 ½" " ½" " " " " ndress + Hauser 13

14 NICHT UNTR SPNNUNG ÖFFNN N IN XPLOSIV TMOSPHR TIGHT W H S WRNUNG VRTISSMNT WRNING LIV PROline Prowirl 72 F, W Dimensions of Prowirl 72 F Flanged version according to: DIN 2501, R a = µm raised face according to DIN 2526 form C for pressure ratings PN , raised face according to DIN 2526 form for pressure ratings PN NSI 16.5, Class , R a = µin JIS 2238, K, R a = µin 149 (142)* ** ** H H 42 D d X L C 151 (144)* 161 PS OUVRIR OUS TNSION N CIRCUIT KP H + 7 = Standard and x i version = Remote version C = x d version (transmitter) * The following dimensions change as follows in the blind version (without local operation): Standard and x i version: the dimension 149 mm changes to 142 mm in the blind version. x d version: the dimension 151 mm changes to 144 mm in the blind version. ** The dimension depends on the cable gland used. F06-72xxxxxx xx-001 Note! In the following tables, dimension H increases by 29 mm in the version with extended temperature range (high temperature version) and in the version with a DSC sensor made of lloy C-22. The weight data refer to the compact version. The weight increases by 0.5 kg for the version with extended temperature range. 14 ndress + Hauser

15 Table: dimensions of Prowirl 72 F according to DIN 2501 DN Pressure rating d [mm] D [mm] H [mm] L [mm] x [mm] Weight [kg] 15 PN PN PN PN PN PN PN PN PN PN PN PN PN PN PN PN PN PN PN PN PN PN PN PN PN PN PN PN PN PN PN PN PN PN PN PN PN PN ndress + Hauser 15

16 Table: dimensions of Prowirl 72 F according to NSI 16.5 DN Pressure rating d [mm] D [mm] H [mm] L [mm] x [mm] Weight [kg] ½" Schedule 40 Cl Cl Cl Cl Cl " Schedule 40 Cl Cl Cl Cl Cl ½" Schedule 40 Cl Cl Cl Cl Cl " Schedule 40 Cl Cl Cl Cl Cl " Schedule 40 Cl Cl Cl Cl Cl " Schedule 40 Cl Cl Cl Cl Cl " Schedule 40 Cl Cl Cl Cl Cl " Schedule 40 10" Schedule 40 12" Schedule 40 Cl Cl Cl Cl Cl Cl ndress + Hauser

17 Table: dimensions of Prowirl 72 F according to JIS 2238 DN Pressure rating d [mm] D [mm] H [mm] L [mm] x [mm] Weight [kg] Schedule 40 20K K K Schedule 40 20K K K Schedule 40 20K K K Schedule 40 10K K K K K Schedule 40 10K K K K K Schedule 40 10K K K K K Schedule 40 10K K K K K Schedule Schedule Schedule 40 10K K K K K K ndress + Hauser 17

18 NICHT UNTR SPNNUNG ÖFFNN N IN XPLOSIV TMOSPHR TIGHT W H S WRNUNG VRTISSMNT WRNING LIV PROline Prowirl 72 F, W Dimensions of Prowirl 72 F, Dualsens version DIN 2501, R a = µm raised face according to DIN 2526 form C for pressure ratings PN , raised face according to DIN 2526 form for pressure ratings PN NSI 16.5, Class , R a = µin JIS 2238, K, R a = µin 149 (142)* ** ** H H 42.5 D d 2 x H H 85 x C 151 (144)* L 161 PS OUVRIR OUS TNSION N CIRCUIT KP H + 7 = Standard and x i version = Remote version C = x d version (transmitter) * The following dimensions change as follows in the blind version (without local operation): Standard and x i version: the dimension 149 mm changes to 142 mm in the blind version. x d version: the dimension 151 mm changes to 144 mm in the blind version. ** The dimension depends on the cable gland used. F06-72xxxxxx xx ndress + Hauser

19 Note! The weight data refer to the compact version. The weight increases by 0.5 kg for the version with extended temperature range. Table: dimensions of Prowirl 72 F Dualsens version according to DIN 2501 DN Pressure d D H L x Weight DIN/JIS rating [mm] [mm] [mm] [mm] [mm] [kg] PN PN PN PN PN PN PN PN PN PN PN PN PN PN PN PN PN PN PN PN PN Table: dimensions of Prowirl 72 F Dualsens version according to NSI 16.5 DN Pressure rating d D H L x Weight NSI [mm] [mm] [mm] [mm] [mm] [kg] Schedule 40 Cl Cl ½" 2" 3" Cl Cl Cl Schedule 40 Cl Cl Cl Cl Schedule 40 Cl Cl Cl Cl Cl ndress + Hauser 19

20 DN Pressure rating d D H L x Weight NSI [mm] [mm] [mm] [mm] [mm] [kg] Schedule 40 Cl Cl " 6" Cl Cl Cl Schedule 40 Cl Cl Cl Cl Cl Table: dimensions of Prowirl 72 F Dualsens version according to JIS 2238 DN Pressure rating d D H L x Weight DIN/JIS [mm] [mm] [mm] [mm] [mm] [kg] 40 Schedule 40 20K K K Schedule 40 10K K K K K Schedule 40 10K K K K K Schedule 40 10K K K K K Schedule 40 10K K K K K ndress + Hauser

21 Dimensions of flow conditioner according to DIN/NSI s Flow conditioner according to DIN/NSI, material (316L) F06-7xxxxxxx xx-001 Table: dimensions of flow conditioner DN 15 / ½" 25 / 1" 40 / 1½" s [mm] DIN PN Weight in [kg] PN PN PN PN NSI Cl Weight in [kg] Cl / 2" 80 / 3" 100 / 4" 150 / 6" 200 / 8" 250 / 10" 250 / 12" Weight Weight of Prowirl 72 W see dimension table on Page 13. Weight of Prowirl 72 F see dimension tables on Page 14 ff. Weight of Prowirl 72 F, Dualsens version see dimen. tab. on Page 18 ff. Weight of flow conditioner according to DIN/NSI see dimension table on Page 21. Material Transmitter housing: Powder-coated die-cast aluminium Sensor: Flanged version: Stainless steel, (351-CF3M), in conformity with NC MR 0175; lloy C-22, ( 494-CX2MW/N 26022) Wafer version: Stainless steel, (351-CF3M), in conformity with NC MR 0175 DSC sensor (differential switched capacitor; capacitive sensor): Wetted parts (marked as wet on the DSC sensor flange): Standard for pressure ratings up to PN 40, Cl 300, JIS 40 K (apart from Dualsens version): Stainless steel (316L), in conformity with NC MR 0175 Higher pressure ratings and Dualsens version: Inconel /N (637) (Inconel 718), in conformity with NC MR 0175 lloy C-22 sensor: lloy C-22, /N 06022, in conformity with NC MR 0175 Non-wetted parts: Stainless steel (CF3) Support: Stainless steel, (CF8) Seal: Graphite (Grafoil) Viton Kalrez 6375 Gylon (PTF) 3504 ndress + Hauser 21

22 Human interface Display elements Operating elements (HRT) Remote operation Liquid crystal display, double-spaced, plain text display, 16 characters per line Display can be configured individually, e.g. for measured variables and status values, totalizers Local operation with three keys (,,) Quick Setup for quick commissioning Operating elements accessible also in x-zones Remote operation possible via: HRT PROFIUS-P FOUNDTION Fieldbus ndress+hauser Service Protocol Certificates and approvals C mark The device is in conformity with the statutory requirements of the C Directives. ndress+hauser confirms successful testing of the device by affixing the C mark. x-approval x i: TX/CNLC II1/2G, x ia IIC T1...T6 (T1...T4 for PROFIUS-P and FOUNDTION Fieldbus) II1G, x ia IIC T1...T6 (T1...T4 for PROFIUS-P and FOUNDTION Fieldbus) II2G, x ia IIC T1...T6 (T1...T4 for PROFIUS-P and FOUNDTION Fieldbus) II3G, x n IIC T1...T6 X (T1...T4 X for PROFIUS-P and FOUNDTION Fieldbus) FM Class I/II/III Div. 1/2, Group...G CS Class I/II/III Div. 1/2, Group...G Class II Div. 1, Group...G Class III x d: TX/CNLC II1/2G, x d [ia] IIC T1...T6 (T1...T4 for PROFIUS-P and FOUNDTION Fieldbus) II2G, x d [ia] IIC T1...T6 (T1...T4 for PROFIUS-P and FOUNDTION Fieldbus) FM Class I/II/III Div. 1, Groups...G CS Class I/II/III Div. 1,2 Groups...G Class II Div. 1, Groups...G Class III More information on the x-approvals can be found in the separate x-documentation. Pressure measuring device approval Certification FOUNDTION Fieldbus Devices with a nominal diameter smaller than or equal to DN 25 correspond to rticle 3 (3) of the C Directive 97/23/C (Pressure quipment Directive). For larger nominal diameters, certified flowmeters to Category III are optionally also available if necessary (depends on fluid and operating pressure). ll devices are applicable for all fluids and instable gases on principle and have been designed and manufactured in accordance to sound engineering practice. The flowmeter has successfully passed all test procedures and is certified and registered by the Fieldbus FOUNDTION. The device thus meets all the requirements of the specifications following: Certified according to FOUNDTION Fieldbus Specification The device meets all the specifications of the FOUNDTION Fieldbus-H1 Interoperability Test Kit (ITK), revision status 4.0 (device certification no. available on request): The device can also be operated with certified devices of other manufacturers Physical Layer Conformance Test of the Fieldbus FOUNDTION 22 ndress + Hauser

23 Certification PROFIUS-P Other standards and guidelines The flowmeter has successfully passed all test procedures and is certified and registered by the PNO (PROFIUS User Organisation). The device thus meets all the requirements of the specifications following: Certified according to PROFIUS-P profile version 3.0 (device certification number available on request) The device can also be operated with certified devices of other manufacturers (interoperability) N 60529: Degrees of protection by housing (IP code). N 61010: Protection measures for electrical equipment for measurement, control, regulation and laboratory procedures. N 61326/1: lectromagnetic compatibility (MC requirements). NMUR N 21: lectromagnetic compatibility (MC) of industrial process and laboratory control equipment. NMUR N 43: Standardisation of the signal level for the breakdown information of digital transmitters with analogue output signal. NC Standard MR0175: Standard Material Requirements - Sulfide Stress Cracking Resistant Metallic Materials for Oilfield quipment. VDI 2643: Measurement of fluid flow by means of vortex flowmeters. ccessories Wafer version mounting set Spare parts as per separate price list Replacement transmitter Prowirl 72 RMS-621 steam computer Compart DXF 351 flow computer Flow conditioner HRT Communicator DXR 275 handheld terminal ctive barrier preline RN 221 N Pressure transducer Cerabar T resp. Cerabar S (PROFIUS-P, FOUNDTION Fieldbus) Thermoresistance Omnigrad TST Process display RI 250, RI 251 Field display RI 261 resp. RID 261 (PROFIUS-P) pplicator FieldTool Fieldgate FX 520 Documentation Operating Instructions PROline Prowirl 72 Operating Instructions PROline Prowirl 72 PROFIUS-P Operating Instructions PROline Prowirl 72 FOUNDTION Fieldbus Related x-documentation System Information PROline Prowirl 72 Related documentation for Pressure quipment Directive ndress + Hauser 23