ULTRA OVAL METER SIZES:29, 60, 31, 32, 33 (Single-case Construction) Register Types A, B, and D

Transcription

1 UT OV METE SIZES:9, 60,,, (Singlecase Construction) egister Types, B, and GENE SPECIICTION GS.No. GENE Our workhorse P flowmeter series is redesigned in this UT OV with the most advanced multifunction electronic register (UT register) capable of indicating the instantaneous flowrate and total flow on an easytoread C and of providing the pulse and output. Significantly improved performance along with compact and lightweight design are among the many benefits it offers. ETUES. Systematic arrangement of pressure rating and temperature range for each model has been restructured.. Microprocessorbased UT register indicates variablestotal flow, both resettable and cumulative, instantaneous flowrate, selectable with mode select switch, plus alarm (low battery alarm) on the C.. Output signal is available in two channels simultaneously in the form of total flow (/0m C factored or unfactored current pulses) and instantaneous flowrate signal ( 0mC analog).. complete series of explosionproof models also available. 5. We also manufacture models approved for applicable highpressure gas control law. 6. With batch controller equipped UT register, you can simply and readily a batch control system. Meter size: 9 Meter sizes:, Meter sizes: 60, GENE SPECIICTIONS Meter Body Item escription Meter size 9 60 Nominal size, mm 0 ( ) 00 ( ) 50 (6 ), 00 ( ) 00 ( ), 50 (6 ) 00 ( ), 50 (6 ) Construction Singlecase construction, pocketless design pplicable fluid Water, petroleums, liquid foods, chemical liquids in general, etc. low range See flow range table (page ). Operating temp. ± 0.5% 0 to +0 C range inearity ± 0.5% 0 to + 60 C inearity ± 0.5% or ± 0.5% epeatability ± 0.05% or ± 0.0% Body SCS Materials otors SUS6 or SUS6 Bearings Carbon bearings or ceramic bearings low direction ight eft (std.), eft ight, Bottom Top, Top Bottom lange atings and Max. Operating Pressures: MPa Pressure ating 0K lange ating JIS 0K lange ating SME, JPI 0K..7 0K Note : eference temperature; 0 C 50 Special Head Office (Tokyo): Tel ax International Sales ivision SK0@oval.co.jp Overseas Branch Offices: Beijing, Seoul, Singapore, Taipei

2 UT OV Meter sizes: 9 to (Single Case) egister Specifications Item Meter size ocal Cumulative totalizing counter display eset counter, 7digits C mode (C) Instantaneous b mode ( ) flowrate (5 digits) b mode None nalog Type Current Pulse (, 5) Pulse width Unit of scaled pulse Type Open Pulse Pulse width collector (, 5) Unit of scaled pulse Type Voltage Pulse (, 5) Pulse width Unit of scaled pulse Without output signal Output signal Power supply Transmission cable With output signal Transmission length wire system Transmission wire system lines wire system mbient temperature Explosionproof configuration pplicable EU directive pplicable EN directive egree of Protection for enclosure Material for housing inish Nominal Meter actors 9 escription 0.00 m (std.) 0.0 m, 0. m 0.0 m /h (std.) m /min (std.) ocal C only to 0mC efer to diagram, page 5. Scaled or unscaled: 0/=/0 mc Scaled: ms ( std. ), 50 ms Unscaled: ms Same as of C counter Scaled or unscaled: Max. V: 0 VC Scaled: ms ( std. ), 50 ms Unscaled: ms 60,,, 0.00 m (std.) 0.0 m, 0. m 0. m /h (std.) 0.00 m /min (std.) allowable current: 50 m Same as of C counter ( ) Scaled or unscaled: 0/= VC Max./7VC Min. Scaled: ms ( std. ), 50 ms Unscaled: ms Same as of C counter ( ) Installed lithium battery ife: years ( years with explosionproof construction and ) External power source: to 5 VC (nalog or current pulse) to VC (Open collector pulse or voltage pulse) to 5 VC (Combination analog and current pulse) Current consumption: Max. 0 mc efer to diagram, page 6. ( ) Capture cable w/external shield (VCT.5 mm, finished O...5 to mm) ( ) Max. km nalog or current pulse Open collector or voltage pulse nalog + current pulse 0 to +60 C (Explosionproof model: 0 to +55 C) (Without dew condensation) Select either one from following two Nonexplosionproof type TIIS Exd B T / Exia B T, Exia B T ( 6) NEPSI Exd B T TEX G Exd B T IP66 (usttight/watertight Type)IEC/EN6059, JIS C 090 luminum die casting Munsell No..5PB5/ baked : If factored pulse units other than above are required, consult the factory. : Battery powered register features a local indicator alone; output signal is not available. : or wiring of explosionproof type, do not fail to use the ancillary pressureresistant packing. lso, in case of TIIS explosionproof type used under the ambient temperature of 5 or higher, use a cable resistant to the temperature of 75 or higher. : Under certain circumstances, the max. flowrate may have limitations if the minimum factored pulse unit is chosen and the pulse width exceeds msec. If this problem arises, consult the factory. 5: If the minimum factored pulse unit is chosen with the capacity indicated by an asterisk, pulse width other than ms is NOT selectable. 6: Explosionproof configuration of UT OV register with batch control function. 7: etails as 9/9/EC compliant explosionproof equipment pplicable hazardous area Zone and Zone EMC 00 / 0 / EC TEX 9 / 9 / EC ( 7) PE 97 / / EC ( ) : s the application to 97/9/EC (Pressurizing instrument order) is dependent on the condition of use, please contact OV representative. Meter Size Nominal meter factor (m/p) req. at max. flowrate (Hz) Max. flowrate (m /h) Pulse (P/rev.) ( ) M Class I, ivision I / Group C, T Ex / Exd B T KOSH Exd B T EMC EN550 : 99 / : 999 Group, Class B EN60006 : 999 TEX EN : 006, EN60079 : 007

3 UT OV Meter sizes: 9 to (Single Case) OW NGES Table low ange for iquid in General (inearity : ±0.5%) (Operating temp. range : 0 to +0 C) Unit in m /h Type of iquid Water iquids other than water 60 C max. 60 C to ess than 0. to 0. to to 5 to 000 to 500 to 0 C 0.mPa s 0.mPa s mpa s 5mPa s 000mPa s 500mPa s 000mPa s Continuous to 0 0 to 5 5 to 50 0 to 50 to 50 6 to 70 to 70 to 60 to Intermittent to 60 0 to 0 5 to 70 0 to 70 to 70 6 to 90 to 90 to 77 to 70.I Continuous 5 to 75 0 to 60 0 to 5 0 to 5 5 to 5 to 0 5 to 0 5 to 0 5 to Intermittent 5 to 0 0 to 75 0 to 5 0 to 5 5 to 5 to 50 5 to 50 5 to 5 5 to 5.I Meter Size Nom. size mm Temp. Viscosity ange Operating Condition Continuous 5 to 0 0 to 90 0 to 0 0 to 0 5 to 0 6 to 0 0 to 0 0 to 50 5 to 0 50 Intermittent 5 to 60 0 to 0 0 to 90 0 to 90 5 to 90 6 to 0 0 to 0 0 to 95 5 to I Continuous 5 to 60 0 to 0 60 to 0 0 to 0 0 to 0 5 to 60 5 to 60 5 to 0 5 to Intermittent 5 to 0 0 to to 70 0 to 70 0 to 70 5 to 0 5 to 0 5 to 75 5 to 5 50.I Continuous 0 to 0 50 to 0 0 to to 50 0 to 50 0 to 60 0 to 60 0 to 05 0 to 0 00 Intermittent 0 to 0 50 to 0 0 to 0 50 to 0 0 to 0 0 to 50 0 to 50 0 to 5 0 to I Table B Meter Size Nom. size mm Type of iquid Temp. Viscosity ange Operating Condition low ange for iquid in General (inearity : ±0.5%) (Operating temp. range : 0 to +60 C) Water iquids other than water Unit in m /h 60 Cmax. ess than 0.mPa s 0. to 0. mpa s 0. to mpa s to 5 mpa s 5 to 000 mpa s 000 to 500 mpa s 500 to 000 mpa s Continuous 5 to 0 to 50 5 to 50 to 50 9 to 70 6 to 70 6 to 60 6 to Intermittent 5 to 60 to 70 5 to 70 to 70 9 to 90 6 to 90 6 to 77 6 to 70.I Continuous 5 to 75 5 to 5 0 to 5 5 to 5 to 0 to 0 to 0 to Intermittent 5 to 0 5 to 5 0 to 5 5 to 5 to 50 to 50 to 5 to 5.I Continuous 0 to 0 60 to 0 0 to 0 5 to 0 5 to 0 5 to 0 5 to 50 5 to 0 50 Intermittent 0 to to 90 0 to 90 5 to 90 5 to 0 5 to 0 5 to 95 5 to I Continuous 50 to to 0 60 to 0 50 to 0 5 to 60 0 to 60 0 to 0 0 to Intermittent 55 to 0 90 to to to 70 5 to 0 0 to 0 0 to 75 0 to 5 50.I Continuous 60 to 0 0 to 50 0 to to to 60 0 to 60 0 to 05 0 to 0 00 Intermittent 60 to 0 0 to 0 0 to 0 70 to 0 50 to 50 0 to 50 0 to 5 0 to I In the Operating Condition column Continuous means continuous operation; Intermittent means no more than hours operation a day, and.i.. indicates allowable instantaneous flowrate. low range should be selected within the Continuous or Intermittent range specified. or applications where viscosity exceeds 00mPa s, specially machined rotors are used. egarding special chemical liquid (liquid ammonia, nitric acid, ammonium sulfate, chlorosulfonic acid, fuming sulfuric acid, sulfuric acid) and highly viscous liquids in excess of 000mPa s, consult factory. egarding liquid ammonia, consult factory. Special

4 OV MOE E000 UT OV Meter sizes: 9 to (Single Case) METE EOS and PESSUE OSSES Error (%) Gasoline 0.mPa s Water mpa s Gas oil mpa s uel oil mpa s Pressure oss (kpa) 0 Meter size lowrate (m /h) Note: Pressure loss varies more or less depending on the meter size. HOOKUP WITH ECEIVING INSTUMENTS eceiving instruments UT OV Totalizer (E0) Batch controller (E series) Pulse divider (SU0) Valve control output Open MOSET Scaled pulse (current, open collector, voltage) Totalizer (E0) Unscaled pulse (current, open collector, voltage) nalog ( to 0mC) Converter, Compensator (E0 ) low computer (E00 series) nalog output Pulse output Pulse output Power supply unit (SU50) ecorder NOTE: Typical examples are shown here. Many other receving instruments are acceptable.

5 UT OV Meter sizes: 9 to (Single Case) WIING CONNECTIONS () Current pulse output (wire system ) ( ) nalog output (wire system) Terminal block V Terminal block SIG 0V G VC Below 600Ω Terminal block V SIG 0V VC Below 600Ω + + to 5VC Power supply nalog indicator Terminal block Oval receiving instrument Oval receiving instrument NOTE: OV offers two circuit configurations to accept current pulses as shown above. See the respective instruction manual of receiving instrument for correct connections. () Current pulse and nalog output (wire system) Tie point G oad resistor Power supply Minimum electrical capacity 60m Totalizer to 5VC nalog indicator : Select voltage signal input for the totalizer. Make sure of the trigger level of incoming voltage signal and determine the supply voltage and load resistance value. In case of current input NOTE: To accept a voltage signal, couple an external load rasistor (see acceptable load resistance range on page 6). NOTE : In an OV receiving instrument, an internal load resistor plays the role of I/V conversion. But if you build a system like the one shown here with a commercially available totalizer, a combination /0m x load resistance serves as a current pulse/voltage pulse converter, make sure of the input level of the totalizer before use. NOTE : With a configuration like the one shown here where an OV receiving instrument is used, make sure of the current carrying capacity of receiving instrument s power supply before use. If found inadequate in current carrying capacity, prepare an additional power supply for the analog indicator. () Open collector pulse (wire system) (5) Voltage pulse (wire system) Terminal block to VC V SIG 0V Max. 50m E ( 0VC) Select so that the allowable current be 50m max. Constant voltage kω Terminal block V SIG 0V to VC Over 0kΩ ms (std.) or 50ms ms (std.) or 50ms Min.7V Max.V ange of oad esistance (for current pulse and analog output) This instrument uses a twowire transmission line for analog and pulse signals, so the line serves for both power supply and signal. C power supply is required for transmission loop. When connecting a meter to the loop, ensure that the meter and the load resistance of cable conductor is within the operating limits shown in the figure at right. Standard: Power supply voltage = VC oad resistance = 50Ω oad resistance (Ω) 660 (600) Operating range () 5 Power supply voltage (V C)

6 UT OV Meter sizes: 9 to (Single Case) OUTINE IMENSIONS (Standard register type provided) [Unit in mm] Meter size: 9 6 Meter size: TEX M0 M NPT TEX and M explosionproof Conduit Connection G/ (female) lange ating JIS 0K JIS 0K Press. ating imensions SME/JPI K pprox. Weight 0K:0.5kg 0K:.5kg 0K TEX M0 M NPT TEX and M explosionproof Conduit Connection G/ (female) pprox. Weight 0K:5kg 0K:90kg Press. ating imensions 0K 0K lange ating JIS 0K JIS 0K SME/JPI or batch controller equipped UT register, refer to General Specification (No. GBC0E). or models provided with auto temperature compensator equipped UT register, consult the factory.

7 UT OV Meter sizes: 9 to (Single Case) OUTINE IMENSIONS (Standard register type provided) [Unit in mm] Meter size: TEX M0 M NPT TEX and M explosionproof Conduit Connection G/ (female) pprox. Weight 0K: 50kg 0K: 55kg Press. ating imensions 0K 0K lange ating JIS 0K JIS 0K SME/JPI Meter size: 00 TEX M0 M NPT 90 TEX and M explosionproof Conduit Connection G/ (female) pprox. Weight : 600kg Press. ating imensions 0K lange ating JIS 0K 00, SME/JPI

8 UT OV Meter sizes: 9 to (Single Case) OUTINE IMENSIONS (Standard register type provided) [Unit in mm] Meter size: 00 TEX M0 M NPT TEX and M explosionproof Conduit Connection G/ (female) pprox. Weight : 50kg Press. ating imensions 0K lange ating JIS 0K SME/JPI or batch controller equipped UT register, refer to General Specification (No. GBC0E). or models provided with auto temperature compensator equipped UT register, consult the factory.

9 UT OV Meter sizes: 9 to (Single Case) POUCT COE EXPNTION Main code Exproof temp. class Explosionproof Process connection Major material Temp. category luid category Nominal diameter Capacity (Nominal iameter) Model Main code egulations egister Power supply Output Version code Bearing Viscosity category Seal material Special / / / dditional code Model U S UT OV (integral type) Single case all stainless 5 Capacity (Nominal iameter) 9 0mm (") N (Small) mm (") N (Big) 00mm or 50mm (" or 6") N (Small (special) or Big) 50mm or 00mm (6" or ") N (Small (special) or Big) 50mm or 00mm (6" or ") N (Small (special) or Big) 6 Nominal diameter Nominal diameter (Small) (Special) Nominal diameter (Big) integral type 7 luid category iquid 9 Temp. category 0 60 and lower Over 60 up to 0 0 Major material C S Z SCS (SUS6) SCS6 (SUS6) Special Process connection J JIS0K J JIS0K Z 9 Special Explosionproof 0 Nonexplosionproof TIIS 5 TEX 6 M 7 NEPSI KOSH T ITI 5 Exproof temp. class 0 Nonexplosionproof T T 6 egulations 0 Standard G High Pressure Gas Safety ct (pproved product) w/material test certificate H J High Pressure Gas Safety ct (Individual test) High Pressure Gas Safety ct (Completion inspection) Gas Business ct (pproved product) w/material test certificate (esigned on PO issued) w/material test certificate w/material test certificate (esigned on PO issued) M Gas Business ct w/material test certificate Q Electricity Business ct (Certificate required) w/material test certificate (esigned on PO issued) Electricity Business ct w/material test certificate T ire Service ct w/material test certificate Z Nuclear power w/material test certificate Special : When register code is "", selectable. : When register code is ", B", selectable. : See General Specification Sheet No. GBC0 for detail. : Consult with OV. 5: When register code is "B", selectable. w/material test certificate (esigned on PO issued) 7 egister Standard UT register B Batch controller equipped UT register (W7E/W76E) uto temp. compensator equipped UT register 9 Power supply 0 External power supply (standard) V Battery drive 0 Output G Standard output (open collector pulse output) nalog Current pulse B Voltage pulse T Current pulse + analog N No output (w/battery unit) Pneumatic step open and close (w/w76e register) 5 Z Special Version code Version code: Bearing 0 Standard (carbon bearing) Standard (strong alkali carbon) Polymerizing liquid (carbon bearing) 5 Hydrogen peroxide solution (ceramic bearing) 6 Highly corrosive polymerizing liquid (ceramic bearing) 7 Polymerizing liquid (carbon bearing) Viscosity category 5 Below 00mPa s (sintered rotors inapplicable) cut rotor 6 00mPa s and over (sintered rotors inapplicable) special cut cut rotor Seal material Oring (PM), gasket (T#0) C Oring (II), gasket (T#0) T Oring (PTE), gasket (V700) P Oring (PTE), gasket (V705) Z Special Special 0 Standard Z Special 9

10 UT OV Meter sizes: 9 to (Single Case) POUCT COE EXPNTION Exproof temp. class Explosionproof Process connection Major material Temp. category luid category Nominal diameter Capacity (Nominal iameter) Model Main code egulations egister Power supply Output Version code Bearing Viscosity category Seal material Special / / / dditional code dditional code Category of High Pressure Gas H P 0 Other than High Pressure Gas H P Toxic gas and flammable gas H P Toxic gas H P lammable gas H P Other than toxic or flammable gas ccuracy 0 5 ±0.50% CCUCY 0 ±0.5% INEITY Only for export 0 ±0.5% INEITY Only for export 0 ±0.0% CCUCY 9 9 Special Operating condition C 0 Continuous M 0 Intermittent Special test (instrumental error) 0 Taxed custody transfer 0 By certified measurer 6 0 Standard oil meter ccording to JMI standard (Bore size 0mm and over) 7 0 Std. fuel oil meter, std. water meter 0 Std. fuel oil meter, std. water meter 9 9 esignation of instrumental error test method ddition of one () test point, etc. low direction 0 0 U 0 T B: Electric conduit at the bottom 0 B T: Electric conduit at the bottom esignated special paint on body B C 0 Corrosion proof B 0 Salinity and acid tolerance 0 and lower B X 0 Customer designation esignated special paint on transmitter S 0 Corrosion proof Special treatment S 0 Salinity tolerance S E 0 cid tolerance Special treatment S X 0 Customer designated paint Special treatment Cleansing T W 0 Nonoil and nonwater treatment T W Nonoil and nonwater treatment equivalent T 0 ood cleansing T 0 Nuclear cleansing T C 0 CIP Choose countermeasure to sudden temp. change abel N P J abel (Japanese) N P E abel (English) ocument S J WG and specifications for approval (Japanese) S E WG and specifications for approval (English) 0 esubmission of WG with specifications C J inal WG (Japanese) C E inal WG (English) P J Calculation sheet (Japanese) P E Calculation sheet (English) S E J Instrumental error test report (Japanese) S E E Instrumental error test report (English) S T J Pressure test report (Japanese) S T E Pressure test report (English) S J irtight test report (Japanese) S E irtight test report (English) J imensional check record (Japanese) E imensional check record (English) S P J Penetrant test report (Japanese) S P E Penetrant test report (English) S M J Magnetic particle inspection (Japanese) S M E Magnetic particle inspection (English) S J adiographic inspection (Japanese) S E adiographic inspection (English) S U J Ultrasonic inspection (Japanese) S U E Ultrasonic inspection (English) S X J PMI test report (Japanese) S X E PMI test report (English) S S J Impact test report (Japanese) S S E Impact test report (English) Y J WPS/PQ (Japanese) Y E WPS/PQ (English) 9 J Photo (Japanese) 9 E Photo (English) T J Inspection procedure (Japanese) T E Inspection procedure (English) C J Inspection certificate: set Only Japanese C B J Inspection certificate: B set Only Japanese C C J Inspection certificate: C set Only Japanese C J Inspection certificate: set Only Japanese Witnessed by customer V 0 equired 0

11 UT OV Meter sizes: 9 to (Single Case)

12 UT OV Meter sizes: 9 to (Single Case) OPETING PECUTIONS This flowmeter is not provided with subtract function. If pulsation in the flow (where the fluid moves back and forth in the pipeline under the influence of pressure) or reversal of flow exists, the total counter may show erratic reading, accumulating all incoming pulses irrespective of flow direction. OEING INOMTION Please complete the following form when making inquiries.. Model. luid to be measured Name Viscosity mpa s Specific gravity. lowrate (m /h) Maximum Normal Minimum. luid temperature ( C) Maximum Normal Minimum 5. mbient temperature ( C) Maximum Normal Minimum 6. Pressure (MPa) Maximum Normal Minimum 7. low direction ight eft, Bottom Top. lange connection Nominal size mm lange rating 9. equired inearity % 0. Explosionproof configuration equired class Not required. ccessories Strainer ir eliminator Companion flange. Quantity Including accessories. eceiving instrument Type, manufacturer, model, specifications (input, output, power supply, etc.). istance between flow meter and receiving device m The specification as of pril, 07 is stated in this GS Sheet. Specifications and design are subject to change without notice. Sales epresentative: GS.No.GBU00E 初版改訂印刷