Auxiliary Sensors Module

Transcription

1 Auxiliary Sensors Module Technical Manual BASM Version 00 BRUKER

2 The information in this manual may be altered without notice. BRUKER accepts no responsibility for actions taken as a result of use of this manual. BRUKER accepts no liability for any mistakes contained in the manual, leading to coincidental damage, whether during installation or operation of the instrument. Unauthorised reproduction of manual contents, without written permission from the publishers, or translation into another language, either in full or in part, is forbidden. This manual was written by P. KRENCKER September, 998: Bruker SA Wissembourg, France Manual P/N: Z80 DWG-Nr: 8 / 00

3 Contents Contents... Description Introduction Description of the BASM BASM front view.... Installation....5 Input connectors... 8 Pt00 connector...9 Thermocouple connector...0 Technical specifications.... W08 (xpt00 inputs).... W08 (xk chromel-alumel inputs).... W08 (xe + xt inputs)... Schematics... 5 Figures... 9 Tables... BASM Version 00 BRUKER ()

4 Contents () BRUKER BASM Version 00

5 Description Introduction. The BASM (Bruker Auxiliary Sensor Module) is an option module for a BVT000 or BVT00 temperature controller unit. The VTU s firmware must be version. or more recent. It is designed for temperature monitoring only, not for sample temperature regulation. It has inputs which can be for Pt00 or thermocouple. The module is mounted on the front panel of the temperature unit. Three modules with different inputs exist : W08 auxiliary sensor module with Pt00. W08 auxiliary sensor module with K thermocouple inputs. W08 auxiliary sensor module with T thermocouple inputs and E thermocouple inputs. Description of the BASM. Figure.. BASM overview CJC CH0 Analog to digital converter mux : CH CH interface CH to microcontroller BASM Version 00 BRUKER 5 ()

6 Description BASM front view. Figure.. BASM front view CH0 CH CH CH module with Pt00 inputs CH0 CH CH CH module with thermocouple inputs Installation. Check that mains is removed from temperature unit. Remove the cover of the temperature unit. Unscrew the small rectangular plate on the front panel and remove also the cover of the module. Insert the module and hold it with screws. Install the cable as shown in figure "Flat cable installation" on page 7. Mount the cover of the module and close the temperature unit. Power on the temperature unit. () BRUKER BASM Version 00

7 Installation Figure.. Flat cable installation cable P/N W098 BASM Version 00 BRUKER 7 ()

8 Description Input connectors.5 For the Pt00 inputs small round LEMO connectors are used. The thermocouple compensated connectors are miniature size and have a shield pin. An adapter cable must be used when connecting a thermocouple with a standard size connector. Table.. Adapter cable list thermocouple type T K E adapter cable W099 W000 W00 Figure.. Adapter cable blue = T violet = E yellow = K color dot 8 () BRUKER BASM Version 00

9 Input connectors Pt00 connector.5. Figure.5. Pt00 connector (front view) Table.. Pt00 connector pin assignment PIN SIGNAL current + measure measure current - BASM Version 00 BRUKER 9 ()

10 Description Thermocouple connector.5. Figure.. Thermocouple connector Table.. Thermocouple connector pin assignment PIN SIGNAL input - frame ground input + 0 () BRUKER BASM Version 00

11 Technical specifications tions W08 (xpt00 inputs). Auxiliary sensor module with Pt00 inputs. Range: -00 C to 800 C. Precision: <±0.5 % of full scale with room C ± C. sensor current: ma. Application: AVANCE spectrometer. Weight: 500 gr. Dimensions: 87 mm (W) x mm (H) x 55 mm (D) aluminium/steel case. Operating temperature: 0to50 C. BASM Version 00 BRUKER ()

12 Technical specifications W08 (xk chromel-alumel inputs). Auxiliary sensor module with K(chromel-alumel) thermocouple inputs. Scale: -00 C to 70 C. Precision: <±0.5 % of full scale with room C ± C. internal CJC (cold junction compensation). small size compensated thermocouple connector with shield pin. Application: EPR spectrometer. Weight: 500 gr. Dimensions: 87 mm (W) x mm (H) x 55 mm (D) aluminium/steel case. Operating temperature: 0to50 C. () BRUKER BASM Version 00

13 W08 (xe + xt inputs) W08 (xe + xt inputs). Auxiliary sensor module with E (chromel-constantan) and T(copper-constantan) thermocouple inputs. Scale T: -00 C to 00 C. Scale E: -00 C to 000 C. Precision: <±0.5 % of full scale with room C ± C. internal CJC(cold junction compensation). E inputs for CH0 and CH. T inputs for CH and CH. small size compensated thermocouple connector with shield pin. Application: AVANCE spectrometer with MAS probe. Weight: 500 gr. Dimensions: 87 mm (W) x mm (H) x 55 mm (D) aluminium/steel case. Operating temperature: 0to50 C. BASM Version 00 BRUKER ()

14 Technical specifications () BRUKER BASM Version 00

15 Schematics BASM Version 00 BRUKER 5 ()

16 () BRUKER BASM Version 00 Figure.. Auxiliary sensors board sheet/ A A -5V ADC_REFOUT C 00N C 00n C 00n C 0u C7 0u A TA TB TC TD X0 X X 5 X Y0 Y 5 Y Y V + G N D 8 V - 7 X Y A 0 B 9 ENA- U 05 SMD A V D D RTD 9 IN+ 7 IN- 8 RTD 0 IN+ 7 A G N D 8 D G N D V S S S Y N C - 5 CLKOUT CLKIN D V D D V B I A S R E F - R E F + 5 R E F O U T DRDY- TFS- 9 RFS- 0 SDATA SCLK A0 MODE U AD77AR PTI DRDY- SDATA TFS- RFS- SCLK A0 X 0 X Y 0 Y Z 0 5 Z I N H A B 0 C 9 X Y 5 Z V C C G N D 8 V S S 7 U 05 SMD C5 00n TYPE A TP7.5V ADC_REFOUT ALIM_RES +5V_PULLUP -5V_PULLDOWN X QUARTZ 0M R.k.5V R8.5k R7 0K TP U LM5CZ S0 S A TA TB TC TD C 00n A C 00n -5V X0 X X 5 X Y0 Y 5 Y Y V + G N D 8 V - 7 X Y A 0 B 9 ENA- U5 05 SMD 0mV / C R 00R R 0R R 0K C0 00n -5V -5V J A0 SDA SDATA SCLK DRDY- TFS- RFS- SCL RST- C7 0u C8 0u A L L TP0 TP C 00n A B QA QB QC 5 QD QE 0 QF QG QH CLEAR- 9 CLK 8 U7 7HC SMD TYPE S0 S ALIM_RES TP8 TP9 JP R9 0K R0 0K SDATA - Extern - Normal TP EXT_SSCLK TP TP5 5 UB 7HC08 SMD TFS- RFS- S0 S PTI PTI PTI PTI PTI C7 00n A C8 00n -5V TP UC 7HC08 SMD A0 UA 7HC08 SMD SCLK R 0K R.7k RST- C 00n C5 0u TST C+ GND C- V+ 8 OSC 7 LV VOUT 5 U8 ICL70CBA TP EXT_SSCLK TP TP TP M C0 0u -5V L C9 0u R0 0R CONVERTER +5v - C5 0u R7 0R R 0K R5 0K SCL SDA 5 A0 A A PTC 7 U9 X0S8 SDA SCL R7 R5 *0K C 00n R LINK S0505.SCH ART: BVTX00 W09 AUXILIARYSENSORS BOARD APPROV: DWG: EC: DATE : DATE : DRAWN : VISA: VISA: SHEET: 0/05/9 WS050 JFP / DP /

17 BASM Version 00 BRUKER 7 () J J C 00n +5V_PULLUP R 0M C 00n L 0u L5 0u C 00n R 0M -5V_PULLDOWN C5 00n C 00n A R8 0M C 00n L 0u L7 0u C 00n R9 0M -5V C7 00n C u 0V C u 0V C u 0V C9 u 0V R 0R R 0R PTI TA TA PTI TB TB R5 0R R 0R UD 7HC08 SMD C 00n C 00n A R0 C 0M J 00n C0 00n R 0M C0 00n C9 00n A R 0M C8 J5 00n C9 00n R 0M C8 00n ART: W09 EC: BVTX00 AUXILIARYSENSORS BOARD L0 L -5V L8 L9-5V 0u 0u 0u 0u DRAWN : DATE : APPROV: DATE : JFP / DP 0/05/9 DWG: WS0505 C5 u 0V C R 0R u 0V C u 0V C7 R 0R u 0V VISA: VISA: SHEET: / PTI TC TC PTI TD TD Figure.. Auxiliary sensors board sheet /

18 Schematics 8 () BRUKER BASM Version 00

19 Figures Description 5 Figure.. BASM overview...5 Figure.. BASM front view... Figure.. Flat cable installation...7 Figure.. Adapter cable...8 Figure.5. Pt00 connector (front view)...9 Figure.. Thermocouple connector...0 Technical specifications Schematics 5 Figure.. Auxiliary sensors board sheet/... Figure.. Auxiliary sensors board sheet /...7 BASM Version 00 BRUKER 9 ()

20 Figures 0 () BRUKER BASM Version 00

21 Tables Description 5 Table.. Adapter cable list... 8 Table.. Pt00 connector pin assignment... 9 Table.. Thermocouple connector pin assignment... 0 Technical specifications Schematics 5 BASM Version 00 BRUKER ()

22 Tables () BRUKER BASM Version 00

23 Lastpage BASM Version 00 BRUKER ()