SMCJ5.0~440(C)A. MAXIMUM RATINGS AND CHARACTERISTICS Ra ngs at 25 C ambient temperature unless otherwise specified. THERMAL CONSIDERATIONS

Size: px

Start display at page:

Download "SMCJ5.0~440(C)A. MAXIMUM RATINGS AND CHARACTERISTICS Ra ngs at 25 C ambient temperature unless otherwise specified. THERMAL CONSIDERATIONS"

Primrose Horn
6 years ago
Views:

1 Transient Suppressors DESCRIPTION The SMCJ series is designed specifically to protect sensi ve electronic equipment from voltage transients induced by lightning and other transient voltage events. FEATURES > Low profile package > Ideal for automated placement > Available in unidirec onal and Bidirec onal > 5 Wa peak pulse power capability with a / μs waveform > For surface mounted applica ons to op mize board space > Excellent clamping capability > Very fast response me > Low incremental surge resistance DO24AB(SMC) PACKAGE Bidirec onal APPLICATIONS TVS devices are ideal for the protec on of I/O Interfaces, VCC bus and other vulnerable circuits used in Telecom, Computer, Industrial and Consumer electronic applica ons. Cathode Anode Unidirec onal SCHEMATIC SYMBOL o MAXIMUM RATINGS AND CHARACTERISTICS Ra ngs at 25 C ambient temperature unless otherwise specified. R AT I N G SY M B O L VA LU E U N I T S Peak Pulse Power Dissipa on on /us waveform (Note,Note2). P P P M 5 Wa s Peak Pulse of on /us waveform(note). I P P M See Table Amps Steady State Power Dissipa on at T =5 (Note2). P M(AV) 6.5 Wa s Peak Forward Surge,8.3ms Single Half SineWave Superimposed on Rated Load, (JEDEC Method) (Note 3). IFS M 2 Amps NOTES:. Nonrepe ve current pulse, TA = Mounted on 8.mm x 8.mm (.3mm thick) Copper Pads to each terminal ms single half sinewave, or equivalent square wave, Duty cycle=4 pulses per minutes maximum. THERMAL CONSIDERATIONS Symbol Parameter Value Unit T J Opera ng Jun con Temperature 55 to +25 T S Storage Temperature Range 55 to +5 RθJA Junc on to Ambient on printed circuit 75 /W Product Datasheet/Rev.26823A Page

2 Transient Suppressors ELECTRICAL CHARACTERISTICS Part Number Device Marking Code Standoff Test Maximum P P Peak Pulse RW M U N TP O L A R B IP O L A R U N I B I V RW M(V) I T(mA) V C(V) I P P(A) I R(uA) SMC J5.A SMC J5.CA G D E B D E SMC J6.A SMC J6.CA G D G B D G SMC J6.5A SMC J6.5CA G D K B D K SMC J7.A SMC J7.CA G D M B D M SMC J7.5A SMC J7.5CA G D P B D P SMC J8.A SMC J8.CA G D R B D R SMC J8.5A SMC J8.5CA G DT B DT SMC J9.A SMC J9.CA G DV B DV SMC JA SMC JCA G DX B DX SMC JA SMC JCA G DZ B DZ SMC J2A SMC J2CA G E E B E E SMC J3A SMC J3CA G EG B EG SMC J4A SMC J4CA G E K B E K SMC J5A SMC J5CA G E M B E M SMC J6A SMC J6CA G E P B E P SMC J7A SMC J7CA G E R B E R SMC J8A SMC J8CA G E T B E T SMC J2A SMC J2CA G E V B E V SMC J22A SMC J22CA G E X B E X SMC J24A SMC J24CA G E Z B E Z SMC J26A SMC J26CA G F E B F E SMC J28A SMC J28CA G F G B F G SMC J3A SMC J3CA G F K B F K SMC J33A SMC J33CA G F M B F M SMC J36A SMC J36CA G F P B F P SMC J4A SMC J4CA G F R B F R SMC J43A SMC J43CA G F T B F T SMC J45A SMC J45CA G F V B F V SMC J48A SMC J48CA G FX B FX SMC J5A SMC J5CA G F Z B F Z SMC J54A S M C J54C A G G E B G E Product Datasheet/Rev.26823A Page 2

3 Transient Suppressors ELECTRICAL CHARACTERISTICS Part Number Device Marking Code Standoff Test Maximum P P Peak Pulse RW M U N TP O L A R B IP O L A R U N I B I V RW M(V) I T(mA) V C(V) I P P(A) I R(uA) SMC J58A SMC J58CA G G G B G G SMC J6A SMC J6CA G G K B G K SMC J64A SMC J64CA G G M B G M SMC J7A SMC J7CA G G P B G P SMC J75A SMC J75CA G G R B G R SMC J78A SMC J78CA G G T B G T SMC J85A SMC J85CA G G V B G V SMC J9A SMC J9CA G G X B G X SMC JA SMC JCA G G Z B G Z SMC JA SMC JCA G H E B H E SMC J2A SMC J2CA G H G B H G SMC J3A SMC J3CA G H K B H K SMC J5A SMC J5CA G H M B H M SMC J6A SMC J6CA G H P B H P SMC J7A SMC J7CA G H R B H R SMC J8A SMC J8CA G H T B H T SMC J2A SMC J2CA G H V B H V SMC J22A SMC J22CA G H X B H X SMC J25A SMC J25CA G H Z B H Z SMC J3A SMC J3CA G J E B J E SMC J35A SMC J35CA G J G B J G SMC J4A SMC J4CA G J K B J K SMC J44A SMC J44CA G J M B J M Product Datasheet/Rev.26823A Page 3

4 Transient Suppressors RATINGS AND CHARACTERISTIC CURVES (T A=25 C unless otherwise noted) Transients or Across TVS Through TVS PPPM Peak Pulse Power (kw) Time.. t d Pulse Width (us) Figure TVS Transients Clamping Waveform Figure 2 Peak Pulse Power Ra ng Curve 5 Peak Pulse Power (P PP )or (I PP ) Dera ng in Percentage % I PPM Peak Pulse, % I RSM 5 tr =µ sec Peak Value I PPM Half Value I I PPM PPM ( 2 ) TJ =25 C Pulse Width(td) is defined as the point where the peak current decays to 5% of I PPM / µ sec. Waveform as defined by R.E.A T A Ambient temperature ( C) td ttime (ms) Figure 3 Pulse Dera ng Curve Figure 4 Pulse Waveform 9. Cj (pf) R R Bidirectional V=V Unidirectional V=V Tj=25 C f=.mhz Vsig=5mVpp.... V BR (V) P M(AV),Steady State Power Dissipa on (W) T A Ambient temperature ( C) Figure 5 Typical Junc on Capacitance Figure 6 Steady State Power Dissipa on Dera ng Curve Product Datasheet/Rev.26823A Page 4

5 Transient Suppressors SOLDERING PARAMETERS Reflow Condion Lead free assembly Temperature Min (Ts(min)) 5 C Pre Heat Temperature Max (Ts(max) 2 C Time (min to max) (ts) Average ramp up rate (Liquidus Temp (TL) to peak 6 8 secs 3 C/second max T P T L T S(max) Rampup Critical Zone TL to TP Reflow T S(max)to T L Rampup Rate 3 C/second max Temperature (T L) (Liquidus) 27 C Time (min to max) (t L) 6 5 seconds T S(min) Rampdown Peak Temperature (TP) 26 C Preheat Time within 5 C of actual peak Temperature (tp) Rampdown Rate 2 4 seconds 6 C/second max 25 Time to peak temperature (t 25 to peak) Time Time 25 C to peak Temperature (T P ) 8 minutes Max. Do not exceed 28 C SMC PACKAGE DIMENSIONS SMC/DO24AB Item Millimeters Inches Min. Max. Min. Max. L D D T T d.2.8 s t RECOMMENDED PAD LAYOUT DIMENSIONS E Item Min. Millimeters Max. Min. Inches Max. B C D A A B C D E REF.32 REF.65 Product Datasheet/Rev.26823A Page 5

6 Transient Suppressors TAPE AND REEL SPECIFICATION.57 (4.).63 (6.) Cathode.35 (8.).59 DIA (.5) Cover tape.8 (2.2) Arbor Hole Dia. 3. (33) Dimensions are in inches (and millimeters) Polarity Band is only applicable to the unidirec onal package.65 (6.4) Direction of Feed ORDERING INFORMATION Part Number Component Package QT Y/Reel Reel Size SMC Jxx(C)A D O24A B(S M C) 3P C S 3" Product Datasheet/Rev.26823A Page 6

7 Transient Suppressors CONTACT US Headquarters A Building Caohejing I&E Park Pujiang Minhang Shanghai China Hotline Web h p:// By Telephone Sales: Customer Service: /8826 Technical Support: By Sales: sales3@semiware.com.cn Customer Service: sales7@semiware.com.cn Technical Support: fae3@semiware.com.cn By Fax General: Sales: COPYRIGHT Semiware 29 This literature is subject to all applicable copyright laws and is not for resale in any manner. SPECIFICATIONS: Semiware reserves the right to change the electrical and or mechanical characteris cs described herein without no ce. DESIGN CHANGES : Semiware reserves the right to discon nue product lines without no ce and that the final judgement concerning selec on and specifica ons is the buyer s and that in furnishing engineering and technical assistance. Semiware assumes no responsibility with respect to the selec on or specifica ons of such products.semiware makes no warranty,representa on or guarantee regarding the suitability of its products for any par cular purpose, nor does Semiware assume any liability arising out of the applica on or use of any product or circuit and specifically disclaims any and all liability without limita on special,consequen al or incidental damages. LIFE SUPPORT POLICY: Semiware products are not authorized for use in life support systems without wri en consent from the factory. Product Datasheet/Rev.26823A Page 7

SIDACtor Protection Thyristors Broadband Optimized TM Protection. TwinChip Series - DO-214. Description

SIDACtor Protection Thyristors Broadband Optimized TM Protection. TwinChip Series - DO-214. Description TwinChip Series - DO-214 RoHS Pb e3 Description TwinChip Series DO-214 are very low capacitance SIDACtor thyristors designed to protect broadband equipment such as VoIP, DSL modems and DSLAMs from damaging