SIDACtor Protection Thyristors Broadband Optimized TM Protection. TwinChip Series - DO-214. Description

Transcription

1 TwinChip Series - DO-214 RoHS Pb e3 Description TwinChip Series DO-214 are very low capacitance SIDACtor thyristors designed to protect broadband equipment such as VoIP, DSL modems and DSLAMs from damaging overvoltage transients. This series provides a surface mount solution that enables equipment to comply with global regulatory standards, while limiting the impact to broadband signals. Features and Benefits Agency Approvals Agency Agency File Number E13383 Pinout Designation NOT APPLICABLE Schematic Symbol Low voltage overshoot Low on-state voltage Does not degrade surge capability after multiple surge events within limit. Low distortion Fails short circuit when surged in excess of ratings Applicable Global Standards TIA/968-A/B ITU K.2/21/45 IEC nd edition GR 189 Intra-building YD/T 182 YD/T 993 * Additional series resistance may be required to comply 4% lower than comparable product RoHS Compliant and Halogen-Free Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is tin(sn (IPC/JEDEC J-STD- 69A.1 YD/T 95 ITU K.2/21/45 Enhanced* GR 189 Inter-building* Electrical Characteristics Part Number =2.2 2V bias V min V max ma min ma max A max V max pf min pf max P642SALRP P62A P722SALRP P72A P92SALRP P92A P112SALRP P112A P132SALRP P132A P152SALRP P152A P182SALRP P182A P232SALRP P232A P262SALRP P262A P32SALRP P32A P352SALRP P352A P422SALRP P422A P482SALRP P482A P62SALRP P62A Table continues on next page.

2 Electrical Characteristics (continued Part Number =2.2 2V bias V min V max ma min ma max A max V max pf min pf max P642SBLRP P62B P722SBLRP P72B P92SBLRP P92B P112SBLRP P112B P132SBLRP P132B P152SBLRP P152B P182SBLRP P182B P232SBLRP P232B P262SBLRP P262B P32SBLRP P32B P352SBLRP P352B P422SBLRP P422B P482SBLRP P482B P62SBLRP P62B P32SCLRP P32C P352SCLRP P352C P422SCLRP P422C P482SCLRP P482C P62SCLRP P62C P72SCLRP P72C Notes: - Absolute maximum ratings measured at T A = 25ºC (unless otherwise noted. - Components are bi-directional. Surge Ratings Series I PP.2/31 1 2/1 1 8/2 1 1/16 1 1/56 1 5/32 1 1/36 1 1/1 1 5/31 1.5/7 2 2/ /5 2 1/16 2 1/56 2 9/72 2 1/36 2 1/1 2 1/7 2 SM 5/6 Hz A min A min A min A min A min A min A min A min A min A min A/µs A B C di/dt Notes: 1 Current waveform in µs 2 Voltage waveform in µs - Peak pulse current rating (I PP is repetitive and guaranteed for the life of the product that remains in thermal equilibrium. - I PP ratings applicable over temperature range of -4ºC to +85ºC - The component must initially be in thermal equilibrium with -4 C < T J < +15 C Additional Information Datasheet Resources Samples

3 Thermal Considerations Package Symbol Parameter Value Unit DO-214AA T J Operating Junction Temperature Range -4 to +15 C T S Storage Temperature Range -65 to +15 C R JA Thermal Resistance: Junction to Ambient 9 C/W V-I Characteristics t r x t d Pulse Waveform +I -V I DRM -I +V IPP Peak Pulse Current %IPP 1 5 t r Peak Value Waveform = t r x t d t d t r = rise time to peak value t d = decay time to half value Half Value t Time (µs Normalized Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature Percent of Change % Junction Temperature (T J C (T C = 25ºC C C Ratio of Case Temperature (T C - ºC

4 Temperature SIDACtor Protection Thyristors Soldering Parameters Reflow Condition Pb-Free assembly (see Fig. 1 - Temperature Min (T s(min +15 C Pre Heat - Temperature Max (T s(max +2 C - Time (Min to Max (t s 6-18 secs. Average ramp up rate (Liquidus Temp (T L to peak 3 C/sec. Max. T S(max to T L - Ramp-up Rate 3 C/sec. Max. Reflow - Temperature (T L (Liquidus +217 C - Temperature (t L 6-15 secs. T P T L T S(max T S(min Preheat t S Figure 1 Ramp-up t P t L Critical Zone TL to TP Ramp-down Peak Temp (T P Time within 5 C of actual Peak Temp (t p Ramp-down Rate Time 25 C to Peak Temp (T P Do not exceed +26(+/-5 C 3 secs. Max. 6 C/sec. Max. 8 min. Max. +26 C 25 time to peak temperature (t 25ºC to peak Time Physical Specifications Environmental Specifications Lead Material Terminal Finish Body Material Copper Alloy 1% Matte-Tin Plated UL Recognized epoxy meeting flammability classification V- High Temp Voltage Blocking Temp Cycling Biased Temp & Humidity 8% Rated (V AC Peak +125 C or +15 C, 54 or 18 hrs. MIL-STD-75 (Method 14 JEDEC, JESD22-A C to +15 C, 15 min. dwell, 1 up to 1 cycles. MIL-STD-75 (Method 151 EIA/JEDEC, JESD22-A14 52 V DC (+85 C 85%RH, 54 up to 18 hrs. EIA/ JEDEC, JESD22-A-11 High Temp Storage +15 C 18 hrs. MIL-STD-75 (Method 131 JEDEC, JESD22-A-11 Part Marking Low Temp Storage Thermal Shock -65 C, 18 hrs. C to +1 C, 5 min. dwell, 1 sec. transfer, 1 cycles. MIL-STD-75 (Method 156 JEDEC, JESD22-A-16 Pxxxx xxxxx Part Marking Code (Refer to Electrical Characteristics Table Date Code Autoclave (Pressure Cooker Test Resistance to Solder Heat +121 C, 1%RH, 2atm, 24 up to 168 hrs. EIA/ JEDEC, JESD22-A C, 3 secs. MIL-STD-75 (Method 231 Moisture Sensitivity Level 85%RH, +85 C, 168 hrs., 3 reflow cycles (+26 C Peak. JEDEC-J-STD-2, Level 1

5 Dimensions DO-214AA E B D K C Case Temperature Measurement Point H A F G.79 (2. Pad Outline.79 (2..11 (2.8 inch (millimeter Dimensions Inches Millimeters Min Max Min Max A B C D E F G H K Part Numbering Packing Options TYPE SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE PACKAGE TYPE P xxx 2S x LRP REEL PACK RoHS COMPLIANT Compliance with RoHS Directive 211/65/EU I PP RATING Package Type S Description Quantity Added Suffix DO-214AA Tape & Reel Industry Standard 25 RP EIA-481-D Tape and Reel Specification DO-214AA.157 ( ( ( (13. Arbor Hole Dia..315 ( ( DIA (1.5 Cover tape Dimensions are in inches (and millimeters..49 (12.4 Direction of Feed Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at