DJ Controller DDJ-SX2

Transcription

1 J-SX J ontroller J-SX ORR NO. RRV THIS MNUL IS PPLIL TO TH OLLOWIN MOL(S) N TYP(S). Model Type Power Requirement Remarks J-SX SVYX 00 V to 0 V J-SX UX 00 V to 0 V J-SX JKLPX 00 V to 0 V J-SX X 00 V to 0 V PIONR ORPORTION -, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa -00, Japan PIONR LTRONIS (US) IN. P.O. ox 0, Long each, 00-0, U.S.. PIONR UROP NV Haven 0, Keetberglaan, 0 Melsele, elgium PIONR LTRONIS SINTR PT. LT. lexandra Road, #0-0, Singapore PIONR ORPORTION 0 K-MZV OT. 0 Printed in Japan

2 STY INORMTION This service manual is intended for qualified service technicians; it is not meant for the casual do-ityourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair to a qualified service technician. WRNIN This product may contain a chemical known to the State of alifornia to cause cancer, or birth defects or other reproductive harm. Health & Safety ode Section. - Proposition (OR US MOL ONLY). STY PRUTIONS The following check should be performed for the continued protection of the customer and service technician. LK URRNT HK Measure leakage current to a known earth ground (water pipe, conduit, etc.) by connecting a leakage current tester such as Simpson Model - or equivalent between the earth ground and all exposed metal parts of the appliance (input/output terminals, screwheads, metal overlays, control shaft, etc.). Plug the line cord of the appliance directly into a 0 V 0 Hz outlet and turn the power switch on. ny current measured must not exceed 0. m. evice under test Test all exposed metal surfaces lso test with plug reversed (Using adapter plug as required) Leakage current tester Leakage Test Reading should not be above 0. m arth ground NY MSURMNTS NOT WITHIN TH LIMITS OUTLIN OV R INITIV O POTNTIL SHOK HZR N MUST ORRT OR RTURNIN TH PPLIN TO TH USTOMR.. PROUT STY NOTI Many electrical and mechanical parts in the appliance have special safety related characteristics. These are often not evident from visual inspection nor the protection afforded by them necessarily can be obtained by using replacement components rated for voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in this Service Manual. lectrical components having such features are identified by marking with a > on the schematics and on the parts list in this Service Manual. The use of a substitute replacement component which does not have the same safety characteristics as the PIONR recommended replacement one, shown in the parts list in this Service Manual, may create shock, fire, or other hazards. Product Safety is continuously under review and new instructions are issued from time to time. or the latest information, always consult the current PIONR Service Manual. subscription to, or additional copies of, PIONR Service Manual may be obtained at a nominal charge from PIONR. J-SX

3 ONTNTS STY INORMTION.... SRVI PRUTIONS.... NOTS ON SOLRIN.... NOTS ON SP P SSY.... SPIITIONS.... SI ITMS OR SRVI.... HK POINTS TR SRVIIN.... JIS LIST.... P LOTIONS.... LOK IRM.... OVRLL WIRIN IRM.... OVRLL LOK IRM INOSIS.... TROULSHOOTIN.... OPRTION HK WITH Serato J.... SRVI MO.... SRVI MO.... ISSSMLY.... H STTIN N JUSTMNT.... NSSRY ITMS TO NOT.... UPTIN O TH IRMWR.... ITMS OR WHIH USR STTINS R VILL.... XPLO VIWS N PRTS LIST PKIN STION XTRIOR STION SHMTI IRM ONTROL P SSY, and TRNSR P SSY SP, OUTPUT and L. P SSYS MIX and R R P SSYS RONT P SSY TOUH P SSY L P SSY.... P ONNTION IRM.... ONTROL P SSY, and TRNSR P SSY.... SP, OUTPUT and L. P SSYS MIX and R R P SSYS.... RONT and TOUH P SSYS.... L P SSY P PRTS LIST... J-SX

4 . SRVI PRUTIONS. NOTS ON SOLRIN or environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit. e sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs accompanied by reworking of soldering. ompared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 0 º. Therefore, for lead-free soldering, the tip temperature of a soldering iron must be set to around º in general, although the temperature depends on the heat capacity of the P board on which reworking is required and the weight of the tip of the soldering iron. o NOT use a soldering iron whose tip temperature cannot be controlled. ompared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting temperatures (hard to melt/easy to harden). The following lead-free solders are available as service parts: Parts numbers of lead-free solder: YP00.0 in dia. YP00 0. in dia. YP00 0. in dia.. NOTS ON SP P SSY or stabilization of power-supply start, the circuitry of the SP P ssy was modified during production. The serial numbers of the J-SX units with the SP P ssy before modification are as follows: Model Not modified R eliminated J-SX/UX to to 0 J-SX/SVYX None to 00 J-SX/JKLPX to 00 0 to 00 J-SX/X ll modified The modified parts in the circuitry are shown below. The circuit diagram indicated in this service manual is that after modification. ll the SP P ssys to be supplied as service parts (Part No.: 0-SMK-00) are modified ones. R eliminated Modified SP P ssy R added J-SX

5 . SPIITIONS adapter Power V to 0 V, 0 Hz/0 Hz Rated current...00 m Rated output... V, eneral Main Unit Main unit weight.... kg (. lb) Max. dimensions... mm (W) 0. mm (H). mm () (. in. (W). in. (H). in. ()) Tolerable operating temperature...+ to + (+ to + ) Tolerable operating humidity... % to % (no condensation) udio Section Sampling rate.... khz /, / converter... bits requency characteristic US, /LIN, MI, MI...0 Hz to 0 khz S/N ratio (rated output, -WIHT) US...0 d /LIN... d PHONO... d MI...0 d Total harmonic distortion (0 Hz 0 khzw) US % /LIN % Standard input level / Input impedance /LIN... du/ kω PHONO... du/ kω MI... du/ kω Standard output level / Load impedance / Output impedance MSTR OUT... + du/0 kω/0 Ω MSTR OUT...+ du/0 kω/ kω OOTH OUT... + du/0 kω/0 Ω PHON... + du/ Ω/ Ω Rated output level / Load impedance MSTR OUT... du/0 kω MSTR OUT... 0 du/0 kω OOTH OUT... du/0 kω rosstalk /LIN... d hannel equalizer characteristic HI... d to + d ( khz) MI... d to + d ( khz) LOW... d to + d (0 Hz) Input / Output terminals input terminal R pin jack... sets PHONO/LIN input terminals R pin jack... sets MI terminal XLR connector/phone jack (Ø. mm)... set MI terminal Phone jack (Ø. mm)... set MSTR OUT output terminal XLR connector... set MSTR OUT output terminal R pin jacks... set OOTH OUT output terminal Phone jack (Ø. mm)... set PHONS output terminal Stereo phone jack (Ø. mm)... set Stereo mini phone jack (Ø. mm)... set US terminal type... set or improvement purposes, specifications and design of this unit and the included software are subject to change without notice. ccessories adapter (-SMK-0) Power plug (SVYX: 0-JM0--H, 0-JM0-0) (UX: 0-JM0-) (JKLPX: 0-JM0-, 0-JM0-0, 0-JM0--H, 0-JM0--H, 0-JM0-0) (X: 0-JM0-0) US cable (0-SU-) Warranty (for some regions) * Operating Instructions (Quick Start uide) (SVYX: 0-JSXM-) (UX: 0-JSXM-) (JKLPX: 0-JSXM-, 0-JSXM-) (X: 0-JSXM-) Serato J XPNSION PK VOUHR * *: or the Japanese region, the corresponding information is provided on the back cover of the Operating Instructions (Quick Start uide). *: Note that the Serato J XPNSION PK VOUHR cannot be reissued. You will need to use the voucher code to activate the expansion pack. Make sure to store it in a safe place so that you do not lose it. J-SX

6 . SI ITMS OR SRVI. HK POINTS TR SRVIIN Items to be checked after servicing To keep the product quality after servicing, confirm recommended check points shown below. No. Procedures heck points heck the firmware version. The firmware version must be the latest one. If it is not the latest one, be sure to update it. onfirm that the customer complaint has been resolved. If the problem pointed out by the customer occurs with a specific source (music file, input channel) or specific operation then perform that operation for checking. heck operations of the each operating elements and Ls. There must be no errors in operations of each button, the Jog dial, Performance pads, needle search pads, VOL, fader control, rotary encoder and Ls in service mode. heck the analog audio output. onnect this unit with a P with the J application (Serato J) installed, via US, then operate J application. The symptoms in question must not be reproduced. There must be no abnormality in audio signals or operations. There must be no errors, such as noise, in audio signals and operations of the MSTR/HPHONS outputs. heck the analog audio input. There must be no abnormality in audio signals or operations. Input an audio signal via each channel (MI/LIN/PHONO). heck the appearance of the product. No scratches or dirt on its appearance after receiving it for service. See the table below for the items to be checked regarding audio. Item to be checked regarding audio istortion Volume too high Noise Volume fluctuating Volume too low Sound interrupted. JIS LIST Jigs List Jig Name Part No. Purpose of use / Remarks US cable P for P connection adapter -SMK-0 ccessory (Note: The power plug part is different.) xtension for diagnosis P -pin (Part No.: 0-S--H) (Two s required for diagnosis Lubricants and lues List Name Part No. Remarks dhesive YL00 Refer to. ISSSMLY. dhesive YL00 Refer to. ISSSMLY. rease M0 Refer to. ISSSMLY. J-SX

7 . P LOTIONS OUTPUT P SSY SP P SSY L P SSY K SNSOR P SSY Top view L. P SSY J TOUH P SSY MIX P SSY J TOUH P SSY TRNSR P SSY TRNSR P SSY ONTROL P SSY H R R P SSY I RONT P SSY ONTROL P SSY ottom view NOTS: - Parts marked by NSP are generally unavailable because they are not in our Master Spare Parts List. - The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. Mark No. escription Part No. Mark No. escription Part No. LIST O SSMLIS..R R P SSY..SNSOR P SSY..MIX P SSY..ONTROL P SSY..ONTROL P SSY..RONT P SSY..TOUH P SSY..TRNSR P SSY 0-N000-0-PJ-00-H 0-SMK-0 0-SMK- 0-SMK- 0-SMK-0 0-SMK- 0-SMK-0..I/O & IX PLT SSY..SP P SSY..OUTPUT P SSY..L P & IX P. SSY..L. P SSY..L & OVR SSY..L P SSY 0-SMK- 0-SMK-00 0-SMK- 0-SMK- 0-SMK- 0-SMK- 0-SMK- J-SX

8 . LOK IRM. OVRLL WIRIN IRM N N SP P SSY (0-SMK-00) N N N : -INTL : -SL : N : -SK : N : -SI : -SOL :.V : PHL N : PH N W : PH : PHR : VL : NL P 0-SMK- N : V : V : : : : : N N : -INTR : -SR : N : -SK : N : -SI : -SOR :.V N N : VL : NL P 0-SMK- N N : _INT : _S : N : _SK : N : _SI : _SO :.V W J TOUH P SSY (0-SMK-) K R W : WL- : V : WL- : N N0 To SNSOR P SSY N W00 N : VL : OL : PL : SHP W00 : PL : NL : VL : NL N00 TRNSR P SSY (0-SMK-0) W0 0P 0-SMK- W0 MIX P SSY (0-SMK-0) K L P SSY (0-SMK-) ONTROL P SSY (0-SMK-) N N0 : V : TP : TP : TP : TP : TP : TP : TP : TP 0: V W00 : V : 0 : N N0 RON P H R R P SSY (0-N000-) N : V : V : : : : : N - When ordering service parts, be sure to refer to "XPLO VIWS and PRTS LIST" or "P PRTS LIST". - The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. J-SX

9 N N N : L.L+ : L.L : L.L- : L.R+ : L.R : L.R- P 0-SMK- N N : OOTH.L+ : OOTH.L- : OOTH.N : OOTH.R+ : OOTH.R- : ML : M : MR OUTPUT P SSY (0-SMK-) W : L+ : L- : N : R+ : R- W : ML : M : MR : L+ : L : L- : R+ : R : R- W L. P SSY (0-SMK-) : _INT : _S : N : _SK : N : _SI : _SO :.V Y 0) N W0 SSY 0-) : WL- : V : WL- : N N0 N : VL : OL : PL : SHP W00 : PL : NL N N00 R TRNSR W K P SSY (0-SMK-0) W00 ONTROL P SSY (0-SMK-) RON P To SNSOR P SSY N0 : V : TP : TP : TP : TP : TP : TP : TP : TP 0: V : VL : NL W J TOUH P SSY (0-SMK-) K R N N or or N N V V W V V N N N N JOT JOR_L WL - WL - WL - WL - NL NL NL or NL 0 0 UL UL PLYL PLYL PL PL OL OL PL PL OL OL PL PL STL STL SL SL 0 0 I N I N N N L K L K N N SHP SHP V V V V K L P SSY (0-SMK-) SP P SSY ONTROL P SSY or ONTROL P SSY N N N : HPL : HP : HP : HPR I RONT P SSY (0-SMK-0) MIX P SSY V 0 0 N N N PWM O PL ST S I N L K VL SHP VL NL V 0 0 N N N PWM O PL ST S I N L K VL SHP VL NL SP P SSY J-SX

10 . OVRLL LOK IRM SP P SSY JK V/ OVP Limit.V Over Voltage Protection VL I TPS INVRTR I TPS0 OOST -V V I 0P I TP0 OOST I KP V.V.V.0V I0 0 V I 0P V V.V ONTRO P SS LT PNL KY SN TT SW * J TOUH P SSY (right) RIHT PNL NL SRH * I0 I/O XPN SR.<-->PL PT LT PNL NL SRH * J TOUH P SSY (left) SPI- UR.V<=>V TT SW * NO * JO WHL * SPI- PIO * STM LIN I I SW OP +.d +.d - - 0d +.d -.d I0 I PM0 I MI (XLR) I I Vbus X M LIN / PHONO LIN / PHONO LIN I +.0d(RI) I +.0d(RI) +.d -.d I I +.d -.d I I I I SW OP +.d I PM0 I PM0 US Port H H H H 0 T (MH I0 O0 (. (IS alance (mono) L MI S +.d I - - 0d +.d I -.d I I PM0 0 J-SX

11 K L P SSY (right) L RIN L * I000-I00 RIHT RIN H * K L P SSY (left) MIX P SSY ONTROL P SSY LT PNL KY SN TT SW * ONTROL P SSY RIHT PNL KY SN TT SW * L RIN L * L IMMR L * I000-I00 LT RIN H * ONTROL P SSY MIX P SSY I00-I0, I0-I0 RIHT PNL H * NTR PNL KY SN TT SW *0 I0 I/O XPN SR.<-->PL. PT LVL MTR 0Ls - PIO * I0 I/O XPN SR.<-->PL. PT SPI- I MU STMS0MT ( MHz) I0 I/O XPN SR.<-->PL. PT * * SPI- L IMMR L * L IMMR L * NO * I00-I0 NTR H * I00-I0, I0-I0 LT PNL H * ONTROL P SSY PIO * SPI- I MU STMS0MT ( MHz) PIO * * SPI- * * * ONTROL P SSY I0 XP. H0 * I00 XP. H0 * XP. I0, I0, I0 H0 * I0 H0 * RIHT PNL VR * TMPO * I RONT P SSY MIX P SSY RONT PNL VR * SLI SW * NTR PNL VR * SLI SW * I LT PNL SR P * RIHT PNL SR P * * I0 XP. H0 * LT PNL VR * TMPO * ONTROL P SSY X M I MLK I0 SK 0 TUS00 PLL X (MHz or MHz) IS0 I0 O0 O LRK K 0 I SP (. MHz) (.K/bit/fs for /,/) (IS format for audio data) 0 X.M 0 SPI- / LK MS,MS,OOTH,HP L & R PNL JO TOUH * I 0 0 PM0 NTR PNL H R * S R * +.0d +.0d I0 I NJM0 NJM0 +.0d +0.0d I NJM0 +.0d I I NJM0 NJM0 L. P SSY OUTPUT P SSY MSTR (XLR) MSTR (R) L R OOTH +.d I NJM J RONT P SSY Headphone ( ohm/.mm &.mm) J-SX

12 . INOSIS. TROULSHOOTIN [] bnormality regarding startup and communications No power. heck that the adapter is securely connected. Is -V power output from the adapter? No The adapter is in failure. Replace the adapter. Yes Is -V power properly output from the SP Pssy? No Q, Q or Q is defective. Replace the defective part. Still when trouble is not repaired, replace the SP P ssy. Yes The UOM (I and I) is in failure. The UOM (I and I) is in failure. Replace the SP P ssy. Yes Is the oscillator oscillating at MHz? I: X I: X No The oscillator (X or X) is defective. Replace the defective part. Yes The UOM (I or I) is defective. Replace the SP P ssy. The unit is not recognized to a P. heck that the US cable is securely connected. heck whether US communication line is fixed at "H" or "L". No The US I (I) is defective. place the defective part. Yes oes not the part on the US line have the abnormality? Part: to, L No The US I (I) is defective. Rplace the defective part. Yes Rplace the defective part. [] bnormality regarding the operating elements and Ls The keys or slide switches do not function. heck that the corresponding wires are properly connected. Is the inoperable switch a direct or matrix key? Matrix key irect key Turn on the corresponding switch and check conduction between the two ends of the switch. If current is not conducted, replace the switch. If current is conducted, the UOM (I) is defective. Replace the SP P ssy. heck whether the corresponding switch is defective or the matrix circuitry is defective. Is there another disabled key in the same segment (S**) or on the same signal line (K**) of the matrix circuitry? No Turn on the corresponding switch and check conduction between the two ends of the switch. If current is not conducted, replace the switch. Yes If the segment or signal line in question is on ONTROL P ssy /, I0 is defective. If it is on the MIX P ssy, I0 is defective. Replace the defective part. J-SX

13 The rotary VRs or slide VRs do not function. heck that the corresponding wires are properly connected. If the defective VR is operated, does the corresponding voltage of signal change? No The VR is defective. Replace the defective part. Yes No Is the defective VR a H fader or crossfader? Yes The UOM (I) is in failure. Replace the SP P ssy. heck the analog SW I to which the corresponding signal is connected. heck whether input signal,, or is fixed at "H" or "L". No The analog SW I is defective. Replace the defective part. Yes The UOM (I) is in failure. Replace the SP P ssy. The rotary selectors do not function. heck that the corresponding wires are properly connected. Which operations do not function, pushing or turning? Pushing See "The keys or slide switches do not function." Turning heck whether the signals from Pins and of the corresponding rotary selector are fixed at "H" when it is turned. No With ROWS: The UOM (I) is defective. With TS: The UOM (I) is defective. Replace the SP P ssy. Yes The rotary selector is in failure. Replace the defective part. There is no response to turning of the jog dial. heck that the corresponding wires are properly connected. heck whether the signals from Pins and of N0 are fixed at "H" when the jog dial is turned. No The UOM (I) is in failure. Replace the SP P ssy. Yes The photo interrupter is defective. Replace the SNSOR P ssy. J-SX

14 There is no response to pressing of the jog dial. The sensitivity when the jog dial is pressed is low. heck that the corresponding wires are properly connected. heck soldering of the wires for signals corresponding to pressing of the jog dial. heck the Sensitivity adjustment value does not lower too much. oes the signal at Pin of N on ONTROL P ssy or N on ONTROL P ssy change in response to pressing of the jog dial? No The PI UOM (I0) is in failure. Replace the defective part. Yes The UOM (I) is in failure. Replace the SP P ssy. NeedleSearch does not function. heck that the corresponding wires are properly connected. Is there any abnormality in the waveforms of signals from Pins,,, or of N or N? Yes No If there is an abnormality in the waveform of the signal from Pin of N or N, the sensor I (I) is defective. Replace the defective part. The UOM (I) is in failure. Replace the SP P ssy. There is no response to touching on the P. heck that the corresponding wires are properly connected. o the signals from Pins of N0 change in response to touching of the P? No P & SR ssy is in failure. Replace the P & SR ssy. Yes The UOM (I) is in failure. Replace the SP P ssy. The Ls do not light. heck that the corresponding wires are properly connected. No re the Ls that do not light those of a level indicator? Yes Is there any other L that does not light in the same segment (S**) or on the same signal line (K**) of the matrix circuitry? No The L is defective. Replace the defective part. Yes The I0 is defective. Replace the defective part.y. Is there only one L that does not light? Yes No heck the transistor to which the L in question is connected. If it is OK, then the I to which the L in question is connected is defective. Replace the I which target L is connected to. heck the diode of the L that does not light. If it is OK, then the I to which the L in question is connected is defective. Replace the I which target L is connected to. J-SX

15 [] bnormality in audio input/output udio is not output from the audio output. heck that the corresponding wires are properly connected. heck that there is no abnormality in the operating element system. Yes Is no audio output from any of the audio output terminals? No re the voltages at the following power-supply Is appropriate? V +V -V Yes No The power circuitry is in failure. See "bnormality in internal power supplies." Is the MUT signal - V? No The MUT drive circuitry is in failure. heck the peripheral circuits of Q. If no problem is found, replace Q. Yes Is the audio waveform output from the output? Yes No heck for digital input to (I). If a signal is input, is in failure. Replace the SP P ssy. If a signal is NOT input, SP (I) is in failure. Replace SP (I). Is the audio signal interrupted around the MUT Tr? No The audio circuitry is in failure. heck the periphery of the OP amplifier. If no problem is found, replace the OP amplifier. Yes The MUT Tr is in failure. Replace it. udio input is not output. heck that the corresponding wires are properly connected. heck that there is no abnormality in the operating element system. No re the level indicators lit? No Yes See "udio is not output from the audio output." Is the LIN/ signal of the channel whose level indicator is unlit output? Yes No heck that the power-supply Is are normal. If any problem is found, see "bnormality in internal power supplies." If no problem is found in the power-supply Is, the audio circuitry is in failure. heck for a point where the audio signal is interrupted then replace the part in failure. Which signal is not output, PHONO or MI? MI See "The MI/MI input signal is not output." PHONO If the LIN/PHONO switching signal is NOT "L," UOM (I) is in failure. If the LIN/PHONO switching signal is "L," the connected transistor is in failure. Replace the part in failure or P ssy. J-SX

16 The MI/MI input signal is not output. heck that the corresponding wires are properly connected. heck that there is no abnormality in the operating element system. When the INPUT SLT switch for the channel whose signal is not output is set to LIN, is the LIN input signal output? No See "The audio input is not output." Yes Is conduction of the wires for the microphone OK? Perform a continuity check between the two ends of each wire. Yes No One of the wires is broken. Replace the broken wire. Is the resistance value of the TRIM VR for the microphone normal? Points to be checked: MI: etween Pins and of W0 MI: etween Pins and of W0 MX: pprox. 0 kohms MIN: pprox. 0 ohm Yes No The TRIM VR for the microphone is in failure. Replace it. The OP amplifier is in failure. heck the peripheral parts. If no problem is found, replace the following part: MI: I MI: I [] bnormality in internal power supplies ither + V or - V power supply is abnormal. heck that the adapter properly supplies V power. Is the voltage on the source side of the T normal? + V: Q - V: Q Yes No The / converter I is in failure. heck the peripheral parts. If no problem is found, replace the / converter I. The T is in failure. Replace it. V is in failure. heck that the adapter properly supplies V power. No Is V output from the output terminal of I0? No Yes bead is in failure. Replace the part in failure. orresponding parts: L, L Is the input to I0 approx.. V? No The / converter I (I) is in failure. heck the peripheral parts. If no problem is found, replace the / converter I. Yes The regulator I is in failure. heck the peripheral parts. If no problem is found, replace the regulator I..V power supply is abnormal. heck that the adapter properly supplies V power. Is the input to I V? Yes No Q, Q, or Q is in failure. Replace the part in failure. If the problem persists, replace the SP P ssy. The regulator I is in failure. heck the peripheral parts. If no problem is found, replace I. If the problem persists, replace the SP P ssy. J-SX

17 .V power supply is abnormal. heck that the adapter properly supplies V power. Is the input to I V? No See "V is in failure." Yes The regulator I is in failure. heck the peripheral parts. If no problem is found, replace I. If the problem persists, replace the SP P ssy. Power supply of.v is abnormal. heck that the adapter properly supplies V power. Is the input to I. V? No See ".V is in failure." Yes The regulator I is in failure. heck the peripheral parts. If no problem is found, replace I. If the problem persists, I is in failure. Replace I. J-SX

18 . OPRTION HK WITH Serato J [Installation of Serato J] brief explanation of how to install Serato J on a P is given below. or details, refer to the operating instructions of the software. If the OS of the P to be used is Windows, install the driver software that enables audio output from the P beforehand. The operating environment of the P required for installation of Serato J is shown below. or the latest information on the required operating environment and compatibility as well as to acquire the latest operating system, refer to Software Info under J-SX on the Pioneer J support site below. Operating System support assumes you are using the latest point release for that version. or the latest version of the Serato J software, access Serato.com and download the software from there. or downloading, registration of a user account at "Serato.com" is required. Unzip the downloaded file, then double-click the unzipped file to launch the installer. Read the terms of the license agreement carefully, and if you agree, select [I agree to the license terms and conditions], then click [Install]. fter installation is completed, the Installation ompleted screen will be displayed. lick on [lose] to terminate the Serato J installer. [Operating procedures] onnect headphones to one of the [PHONS] terminals. onnect powered speakers, a power amplifier, components, etc., to the [MSTR OUT ] or [MSTR OUT ] terminals. onnect this unit to your computer via a US cable. Turn on the computer s power. onnect the adapter. Press the [STNY/ON] switch on this unit s rear panel to turn this unit s power on. Turn on the power of the devices connected to the output terminals (powered speakers, power amplifier, components, etc.). [onnections] J-SX

19 Starting the system or Windows rom the Windows [Start] menu, click the [Serato J] icon under [ll Programs] > [Serato] > [Serato J]. or Windows. rom [pps view], click the [Serato J] icon. or Mac OS X In inder, open the [pplications] folder, then click the [Serato J] icon. omputer screen directly after the Serato J software is launched (The ight screen at the unit is not connected to a P) The [UY/TIVT] icon may appear on the right side of the screen displayed when Serato J is launched for the first time, but for those using J-SX there is no need to activate or purchase a license. You can purchase extended packs such as VS and use them as additional options. lick [Online] to use the unit as is. omputer screen when a track is loaded in the Serato J software lick [Library] at the upper left of the computer screen, then select [Vertical] or [Horizontal] from the pull-down menu to switch the Serato J screen. eck section The track information (the name of the loaded track, artist name, PM, etc.), the overall waveform and other information is displayed here. Waveform display The loaded track s waveform is displayed here. rowser section rates in which tracks in the library or sets of multiple tracks are stored are displayed here. J-SX

20 Importing tracks lick the [iles] key on the Serato J software screen to open the [iles] panel. lick the folder on the [iles] panel containing the tracks you want to add to the library to select it. On the Serato J software screen, drag and drop the selected folder to the crates panel. a a b : [iles] panel : rates panel b Loading tracks and playing them Press this unit s [K] button, move the cursor to the crates panel on the computer s screen, then turn the rotary selector to select the crate, etc. Press the rotary selector, move the cursor to the library on the computer s screen, then turn the rotary selector and select the track. Press the [LO] button to load the selected track onto the deck. a b a b : Library : rates panel Playing tracks and outputting the sound Set the positions of the controls, etc., as shown below. Press the [f] button to play the track. Move the channel fader () away from you. Turn the [TRIM] control (). djust [TRIM] so that the orange indicator on the channel level indicatorlights at the peak level. Turn the [MSTR LVL] control () to adjust the audio level of the speakers. Monitoring sound with headphones Set the positions of the controls, etc., as shown below. 0 J-SX

21 . SRVI MO. SRVI MO [] rror larming When the controller detects following types of problem while the controller is launching or working, it should indicate using Ls so that user notices the problem. No. uilt-in LSH ROM of MIN UOM Part where problem occurs Symptom ontroller's behavior when detect the problem When firmware is updated, the internal data on LSH ROM can not be erased. When firmware is updated, the update data can not be written to LSH ROM correctly. US controller lthough the controller connects with a computer via US cable, the US controller within the controller can not communicate with the computer. L within X assign button for eck should be flashed in cycle of second. (*) L within X assign button for eck should be flashed in cycle of second. *: When the controller launches next, same L should be flashed. [] Service mode [How to enter Service mode] Turn on the power while pressing both left "SHIT" button and the "K " button or while pressing both right "SHIT" button and the "K " button. Ls of hannel Level Indicator (H), hannel Level Indicator (H), and hannel Level Indicator (H) should be lit depending on the firmware version and other Ls should be unlit right after the controller launches in Service mode. Note: ven if the controller connects with a computer via US cable, it does not communicate with the computer during Service mode. Unused Ls should be unlit during Service mode. [How to exit Service mode] In order to exit Service mode, turn off the power. [Note] When in this mode, the firmware version display appear first. In this mode, it does not work to communicate with computer via US. In this mode, L dimmer is not available. irmware version (x.xx) into Service mode into Service mode J-SX

22 . onfirmation of firmware version Ls of hannel Level Indicator (H) indicate first digit of the firmware version. (*) Ls of hannel Level Indicator (H) indicate second digit of the firmware version. (*) Ls of hannel Level Indicator (H) indicate third digit of the firmware version. (*) The firmware version is indicated right after the controller launches in Service mode. (*) x.xx not used 0 (all off) bove figure is shown "Ver...". *: If the firmware version is "0", all segments of the hannel Level Indicator are unlit. *: If any hannel fader is slid, state of the hannel fader is indicated instead of firmware version.. heck of buttons ll buttons on this controller can be checked using Ls in Service Mode. J-SX

23 Table- L behavior of when buttons are checked roup Trigger Press Press Press etails L color is changed as follows whenever the button is pressed. ven if the button is released while the L is lit, the controller holds lighting. (The L is embedded within the button.) White Red Yellow reen yan lue Magenta Unlit White L is lit while the button is pressed and held. When the button is released, the L is unlit. (The L is embedded within the button.) L within HOT U Mode button of the same side is lit with blue color while the "" button is pressed and held. When the "" button is released, the L is unlit. (L within the HOT U Mode button is used in order to check the "" button.) L within SMPLR Mode button of the same side is lit with blue color while the "" button is pressed and held. When the "" button is released, the L is unlit. (L within the SMPLR Mode button is used in order to check the "" button.) L within the HPHON U (H) button is lit while the "" button is pressed and held. When the "" button is released, the L is unlit. (L within the HPHON U (H) button is used in order to check the "" button.) L within right SYN button is lit while the "" button is pressed and held. When the "" button is released, the L is unlit. (L within right SYN button is used in order to check the "" button.) L within left NSOR button is lit while the "" button is pressed and held. When the "" button is released, the L is unlit. (L within left NSOR button is used in order to check the "" button.). heck of rotary knobs, sliders and NL SRH pads ll rotary knobs, sliders and NL SRH pad on this controller can be checked using Ls in Service Mode. J-SX

24 Table- L behavior of when rotary knobs, sliders and NL SRH pads are checked roup Trigger etails Turn Lighting position of white Ls of Jog dial of the same side is moved depending on the turned amount. Refer to igure-. Lighting position of white Ls of both side Jog dials are moved depending on the turned amount. Refer to igure-. Slide Lighting position of white Ls of Jog dial of the same side is moved depending on the slid amount. If the position after sliding is upper than center, The upper "TMPO slider Take-over" indicator of the same side is lit. If the position after sliding is lower than center, The lower "TMPO slider Take-over" indicator of the same side is lit. If the position after sliding is center, The upper and lower "TMPO slider Take-over" indicators of the same side are unlit. Refer to igure-. Lighting of hannel Level Indicator of the same channel is changed depending on the slid amount. Refer to igure-. Lighting of Master level indicator is changed depending on the slid amount. Refer to igure-. Lighting position of white Ls of both side Jog dials are moved depending on the slid amount. Refer to igure-. Touch and move Lighting position of white Ls of Jog dial of the same side is moved depending on the touching position. Refer to igure-. igure- L behavior of when a rotary knob is turned, a slider is slid, or a NL SRH pad is touched and moved When position of the knob is center, these Ls are lit. When position of the slider is center, these Ls are lit. When position of rossfader is center, these Ls are lit. When touching position of the NL SRH pad is center, these Ls are lit. When the knob is fully turned counterclockwise, these Ls are lit. When position of the slider is top, these Ls are lit. When position of rossfader is left edge, these Ls are lit. When the touching position of the NL SRH pad is left edge, these Ls are lit. When the knob is fully turned clockwise, these Ls are lit. When position of the slider is bottom, these Ls are lit. When position of rossfader is right edge, these Ls are lit. When the touching position of the NL SRH pad is right edge, these Ls are lit. igure- L behavior of when a hannel fader is slid This controller has hannel faders with 0 bit resolution. ut, hannel Level Indicator is only steps. Therefore, the controller should round the actual position data to steps. When position of the hannel fader is bottom, all segments of the hannel Level Indicator should be unlit. When position of the hannel fader is top, all segments of the hannel Level Indicator should be lit. J-SX

25 igure- L behavior of when the SMPLR VOLUM fader is slid This controller has the SMPLR VOLUM fader with 0 bit resolution. ut, Master level indicator is only steps. Therefore, the controller should round the actual position data to steps. When position of the SMPLR VOLUM fader is bottom, all segments of the Master level indicator should be unlit. When position of the SMPLR VOLUM fader is top, all segments of the Master level indicator should be lit.. heck of rotary encoders, slide SWs, and Jog dials ll rotary encoders, slide SWs, and Jog dials on this controller can be checked using Ls in Service Mode. H H H I I J-SX

26 Table- L behavior of when rotary encoders, slide SWs, and Jog dials are checked roup Trigger etails Slide Lighting position of white Ls of Jog dial of the same side is moved clockwise whenever position of the slide SW is moved. Refer to igure-. H H Press L lighting is changed as shown in following order whenever the Rotary selector is pressed. ven if the Rotary selector is released while the Ls are lit, the controller holds lighting. ll Ls are lit with full brightness. (L color of the Pad Mode buttons and Pads is white.) ll Ls are lit with full brightness. (L color of the Pad Mode buttons and Pads is red.) ll Ls are lit with full brightness. (L color of the Pad Mode buttons and Pads is yellow.) ll Ls are lit with full brightness. (L color of the Pad Mode buttons and Pads is green.) ll Ls are lit with full brightness. (L color of the Pad Mode buttons and Pads is cyan.) ll Ls are lit with full brightness. (L color of the Pad Mode buttons and Pads is blue.) ll Ls are lit with full brightness. (L color of the Pad Mode buttons and Pads is magenta.) ll Ls are lit dimly. (L color of the Pad Mode buttons and Pads is white.) ll Ls are lit dimly. (L color of the Pad Mode buttons and Pads is red.) ll Ls are lit dimly. (L color of the Pad Mode buttons and Pads is yellow.) ll Ls are lit dimly. (L color of the Pad Mode buttons and Pads is green.) ll Ls are lit dimly. (L color of the Pad Mode buttons and Pads is cyan.) ll Ls are lit dimly. (L color of the Pad Mode buttons and Pads is blue.) ll Ls are lit dimly. (L color of the Pad Mode buttons and Pads is magenta.) ll Ls are unlit. Turn Lighting position of white Ls of both side Jog dials are moved whenever the Rotary selector is turned. Refer to igure-. H Press L within the TP button of the same side is lit while the rotary encoder is pressed and held. When the rotary encoder is released, the L is unlit. Turn Lighting position of white Ls of Jog dial of the same side is moved whenever the rotary encoder is turned. Refer to igure-. I Touch ll white and red Ls of Jog dial are lit while top surface of the Jog dial is touched and held. When top surface of the JO is released, the Ls are unlit. Turn Lighting position of white Ls of Jog dial is moved when the Jog dial is turned. Refer to igure-. igure- L behavior of when a slide SW is slid, a rotary encoder is turned, or a Jog dial is turned *: Only when positon of a slide SW is moved, lighting position of white L is moved clockwise. *: The starting position depends on the last position. J-SX

27 . actory reset ll settings in Utilities mode and adjustment value for Jog dial touch sensitivity can be initialized in Service mode. [Trigger to initialize] In order to initialize all settings in Utilities mode, press and hold both left and right SYN buttons for over seconds during Service mode. [Posterior condition] Ls wihin both left and right SYN buttons are lit while the controller is initializing the settings. When the initialization is completed, the Ls are unlit. *: ll settings in Utilities mode are initialized. djustment values for left and right Jog dial touch sensitivity are returned to center value. actory Reset. heck of velocity ehavior of velocity can be checked using hannel Level Indicator in Service Mode. [Preparation to check velocity] In order to check the velocity, press both left and right HOT U Mode buttons firstly during Service mode. In order to select Pads of which check the velocity, press left Pad Mode button. Relation between left Pad Mode button and checkable Pad is shown in Table-. State transition between Service mode and Velocity check mode is shown in igure-. Table- Relation between left Pad Mode button and checkable Pads Mode Velocity check mode heckable Pads Left Pad, Pad, Pad, and Pad *: L within the pressed Pad Mode button is lit with blue color. Pad Mode button Left HOT U Mode button (*) Velocity check mode Left Pad, Pad, Pad, and Pad Left ROLL Mode button (*) Velocity check mode Right Pad, Pad, Pad, and Pad Left SLIR Mode button (*) Velocity check mode Right Pad, Pad, Pad, and Pad Left SMPLR Mode button (*) In order to return from Velocity check mode to Service mode, press the Rotary selector. Then the controller should return to condition right after it launches in Service mode. J-SX

28 igure- State transition between Service mode and Velocity check mode Press the Rotary selector. Service mode Press the Rotary selector. Press the Rotary selector. Press both left and right HOT U Mode buttons. Press left HOT U Mode button. Press left ROLL Mode button. Velocity check mode Left Pad, Pad, Pad, and Pad are checkable. Press left HOT U Mode button. Press left SMPLR Mode button. Velocity check mode Left Pad, Pad, Pad, and Pad are checkable. Press left ROLL Mode button. Press left SLIR Mode button. Press left HOT U Mode button. Press left SLIR Mode button. Velocity check mode Right Pad, Pad, Pad, and Pad are checkable. Press left SMPLR Mode button. Press left SLIR Mode button. Velocity check mode Right Pad, Pad, Pad, and Pad are checkable. Press the Rotary selector. Press left SMPLR Mode button. Service mode Press left ROLL Mode button. [Trigger of which check velocity] ) Press left Pad, Pad, Pad, or Pad when L within left HOT U Mode button is lit with blue color. ) Press left Pad, Pad, Pad, or Pad when L within left ROLL Mode button is lit with blue color. ) Press right Pad, Pad, Pad, or Pad when L within left SLIR Mode button is lit with blue color. ) Press right Pad, Pad, Pad, or Pad when L within left SMPLR Mode button is lit with blue color. [Posterior condition] ) Lighting of hannel Level Indicator (H) is changed depending on pressure force of the pressing Pad (*). ) Lighting of hannel Level Indicator (H) is changed depending on pressure force of the pressing Pad (*). ) Lighting of hannel Level Indicator (H) is changed depending on pressure force of the pressing Pad (*). ) Lighting of hannel Level Indicator (H) is changed depending on pressure force of the pressing Pad (*). *: When L within left HOT U Mode button is lit with blue color, hannel Level Indicator (H) is used in order to check velocity of left Pad. When L within left ROLL Mode button is lit with blue color, hannel Level Indicator (H) is used in order to check velocity of left Pad. When L within left SLIR Mode button is lit with blue color, hannel Level Indicator (H) is used in order to check velocity of right Pad. When L within left SMPLR Mode button is lit with blue color, hannel Level Indicator (H) is used in order to check velocity of right Pad. *: When L within left HOT U Mode button is lit with blue color, hannel Level Indicator (H) is used in order to check velocity of left Pad. When L within left ROLL Mode button is lit with blue color, hannel Level Indicator (H) is used in order to check velocity of left Pad. When L within left SLIR Mode button is lit with blue color, hannel Level Indicator (H) is used in order to check velocity of right Pad. When L within left SMPLR Mode button is lit with blue color, hannel Level Indicator (H) is used in order to check velocity of right Pad. *: When L within left HOT U Mode button is lit with blue color, hannel Level Indicator (H) is used in order to check velocity of left Pad. When L within left ROLL Mode button is lit with blue color, hannel Level Indicator (H) is used in order to check velocity of left Pad. When L within left SLIR Mode button is lit with blue color, hannel Level Indicator (H) is used in order to check velocity of right Pad. When L within left SMPLR Mode button is lit with blue color, hannel Level Indicator (H) is used in order to check velocity of right Pad. *: When L within left HOT U Mode button is lit with blue color, hannel Level Indicator (H) is used in order to check velocity of left Pad. When L within left ROLL Mode button is lit with blue color, hannel Level Indicator (H) is used in order to check velocity of left Pad. When L within left SLIR Mode button is lit with blue color, hannel Level Indicator (H) is used in order to check velocity of right Pad. When L within left SMPLR Mode button is lit with blue color, hannel Level Indicator (H) is used in order to check velocity of right Pad. *: This controller's velocity has resolution of steps. ut, hannel Level Indicator is only steps. So, the controller should round the actual velocity value to steps so that indicate behavior of velocity using hannel Level Indicator during Velocity check mode. *: Lighting of hannel Level Indicator should be applied pressure force of not only initial touch (velocity) but also after touch during Velocity check mode. J-SX

29 igure- Relation between Pad and hannel Level Indicator during Velocity check mode (ollowing example is left-side. It is the same for right-side.) igure- Relation between pressure force and lighting segment few segment is lit. Many segments are lit. Tap a Pad weakly Tap a Pad hard J-SX

30 [] Measurement mode This controller can measure "Jog dial rotation time" and drift of knobs and faders in Measurement mode. [How to enter Measurement mode] Turn on the power while pressing both left SHIT button and the K button. Ls within the K button, K button, and left X - ON button should be lit and other Ls should be unlit right after the controller launches in Measurement mode. Note: ven if the controller connects with a computer via US cable, it does not communicate with the computer during Measurement mode. Unused Ls should be unlit during Measurement mode. [How to exit Measurement mode] In order to exit Measurement mode, turn off the power. These Ls are lit right after the controller launches in Measurement mode. into Measurement mode 0 J-SX

31 . Measurement of Jog dial rotation time This controller should measure the rotation time by rotating Jog dial during Measurement mode. In particular, when Jog dial is turned with. rpm (. X ) or more during Measurement mode, the controller should measure difference between time of when the rotation speed slows down to. rpm (. X ) and time of when it slows down to. rpm (. X.). (The controller should measure "T" shown in igure-.) ut, when the rotation speed is less than. rpm, the controller does not measure. igure- haracteristic example of when Jog dial is turned 0 rpm Speed up Slow down Rotation speed 0 rpm 00 rpm 0 rpm Jog dialrotation is started. Time T Jog dial rotation is stopped [Trigger of which measure Jog dial rotation time] ) In order to measure the rotation time for left-side Jog dial, turn left-side Jog dial clockwise or counterclockwise during Measurement mode. ) In order to measure the rotation time for right-side Jog dial, turn right-side Jog dial clockwise or counterclockwise during Measurement mode. [Posterior condition] When the rotation speed is more than. rpm, measurement value ("T" shown in igure-) is indicated using hannel Level Indicator and Ls within left side SLIP buttons are unlit (*). Indication method by hannel Level Indicator is common to both side. The measurement unit is "milli second". When the rotation speed is less than. rpm, all hannel Level Indicators are unlit and L within SLIP button of the left side is lit. The specified range is ± msec. x x x bove figure is shown " msec". not used 0 (all off) *: If a place of a measurement value is "0", all segments of the related hannel Level Indicator are unlit. hannel Level Indicator (H) is not used in Measurement mode. J-SX

32 . heck of drift of knobs and faders rift of all knobs and faders can be checked using Master level indicator during Measurement mode. In order to select test subject, turn the Rotary selector clockwise or counterclockwise. Then, lighting L is moved whenever the Rotary selector is turned. In order to start or reset observation of drift, press the Rotary selector. [Use of this mode during repair] or failure judgment of the rotary VRs s a guide, amplitude values higher than + or lower than - may be judged as failure. The VRs can be set to any position during measurement. Possible symptoms are shown below. The volume changes arbitrarily. Interrupted sound leakage occurs even if the volume is decreased to the minimum at the Master or ooth Monitor. The MII signal is output even if the corresponding VR is not operated. or operation check of a rotary VR after replacement igure- Relation between knob/fader and L Knobs and faders painted with light blue color are checkable. Number in this figure means order of which select test subject J-SX

33 [Preparation of when check drift] irstly, Select knob or fader of which check drift. In order to select it, turn the Rotary selector clockwise or counterclockwise. Whenever the Rotary selector is turned, lighting L is moved according to the order shown in igure-. Knob or fader of which check drift can be identified by lighting L. [Trigger of which observe drift] In order to start observation of drift, press the Rotary selector. In order to clear measured result of drift and start new observation of drift, press the Rotary selector again. The controller should store / converted value for knob/fader as "reference value" right after the Rotary selector is pressed. The controller should always calculate difference between the "reference value" and latest value during observation. The controller should indicate maximum difference value until now as drift. If latest difference value is more than past maximum difference value, the drift value should be used the latest difference value. If not, the drift value should be used not the latest difference value but past maximum difference value. [Posterior condition] Segments of Master level indicator are lit depending on amount of the drift. The controller should always indicate both negative and positive maximum drift value at the same time until the Rotary selector is pressed next. Table- Relation between amount of drift and Master level indicator mount of drift Master level indicator Lighting segments Lighting pattern Side + - d Pattern Right-side + - d and - d Pattern Right-side + - d, - d and 0 d Pattern Right-side + - d, - d, 0 d and + d Pattern Right-side + or more - d, - d, 0 d, + d and "OVR" Pattern Right-side - "OVR" Pattern Left-side - + d and "OVR" Pattern Left-side - 0 d, + d and "OVR" Pattern Left-side - - d, 0 d, + d and "OVR" Pattern Left-side - or less - d, - d, 0 d, + d and "OVR" Pattern 0 Left-side igure-0 Lighting pattern of Master level indicator during drift observation Pattern Pattern Pattern Pattern Pattern Pattern Pattern Pattern Pattern Pattern 0 J-SX

34 . ISSSMLY Note: ven if the unit shown in the photos and illustrations in this manual may differ from your product, the procedures described here are common. Knobs and Volumes Location 00-S-00-H 00-S-00-H 00-S-00-H 00-S-00-H White White lack lack lack lack 00-S-00-H White lack 00-S-00-H White lack 00-SXMK- White lack J-SX

35 isassembly [] SP and OUTPUT P ssemblies ase () Remove the ase by removing the screws. (0-PTP0--H) ase Screw tightening order 0 0 ottom view Shield () Remove the screws. (0-MP--H) () Remove the Isolation plate by removing the screws. ( H) () Remove the screw. (0-N-) () Remove the screw. (0-SL-0-H) () Remove the screw. (0-QMXPM--H) () Remove the over by removing the screw. ( H) over Isolation plate ottom view SP and OUTPUT P ssemblies () Remove the Strain relief bush by removing the screw. (0-T0--H) () Remove the screws. (0-MP--H) () Remove the round terminal and washer. Rear view Screw tightening order J-SX

36 () isconnect the flexible cable and connectors. (N,,,,,, ) () Remove the Output board with P ssemblies by removing the screws. ( H) Screw tightening order 0 N N N N N N N MIX P ssy ottom view RONT P ssy arth lead Note on connection of the flexible cable (N) N N Tuck the flexible cable between the P boards. () isconnect the flexible cables and connectors. (N,,,, ) Screw tightening order (reference information) 0 N N OUTPUT P ssy N SP P ssy N N When replacing the US JK When the US JK in the SP P ssy is to be replaced, the US fixing bracket (US fixed plate) must be detached together with it. To detach them, remove the solder from the JK and US fixed plate. ONTROL P ssy ONTROL P ssy US fixed plate US JK ottom view J-SX

37 iagnosis of SP P ssy When you diagnose SP P ssy in an electricity state, perform it in the following procedures. xtension s to be used: P ( pcs) Step : Perform the disassembly steps up to Step () described in [] SP, OUTPUT P ssy in "ISSSMLY." Remove the L. P ssy. SP, OUTPUT P ssy L. P ssy Step : isconnect the s and and the wires and then turn over the SP P ssy toward the front side. Step : Replace the s and with the ones for diagnosis. xtension (P) for diagnoses Step : onnect the adapter and cables. iagnosis J-SX

38 [] Jog dial section Note: figure is only left K side, but the right side is similar, too. SNSOR P ssy () Remove the ust-proof slice by removing the screws. (0-PROS--H) ust-proof slice ottom view () isconnect the connector. (N0) () Remove the Sensor fixed plate by removing the screws. (0-J00--H) () Remove the SNSOR P ssy. SNSOR P ssy Sensor fixed plate N0 ottom view Jog dial section () Remove the solders. () Remove the nut and washer. () Remove the JW L base by removing the screws. (0---H) JW L base TRNSR P ssy ottom view () Remove the ring. ottom view J-SX

39 () Remove the jog dial section. Jog dial section L P ssy () Remove the Windows lens. Insert a slim rod in the hole for disassembly in the jog dial section bottom side, and remove it. Windows lens L & OVR ssy Hole WHL ssy ottom view () Remove the L & OVR ssy. () Remove the JW cover by unhooking the hooks. () Remove the L P ssy. JW cover When replacing the L & OVR ssy or WHL ssy When replacement of the L & OVR ssy is required, the Windows Lens must be detached, because the Windows Lens is attached to the WHL ssy with double-back tape, which is attached around the outer periphery of the Windows Lens as a tube, and the L & OVR ssy is placed in between them. Once the Windows Lens is detached, the double-back tape cannot be reused. The Windows Lens may not be reused either, because it may be scratched, depending on the manner in which it was detached. When replacement of the WHL ssy is required, the Windows Lens must also be detached and may not be reused. Note that when replacement of the following ssys are required, replace them together with the parts mentioned below. ouble-back tape is supplied with the WHL ssy. When the L & OVR ssy is to be replaced: ouble-back tape (TWIN HSIV) (must), Windows Lens (if necessary) When the WHL ssy is to be replaced: Windows Lens (if necessary) L P ssy ottom view J-SX

40 [] ach P ssemblies Note: When you remove each P ssemblies, it is not necessary to remove a jog dial section. R R P ssy () Remove the Push button. () Remove the Panel & ushion ssy by removing the screws. (0-T00--H) () Remove the R R P ssy. Panel & ushion ssy R R P ssy () isconnect the connector. (N0) N0 R R P ssy L. P ssy () Remove the L. P ssy by removing the screws. (0-J00--H) L. P ssy ottom view RONT P ssy () Remove the ain rotate knobs. () Remove the screws. (0-MP--H) () Remove the RONT P ssy by removing the screws. (0-J00--H) Screw tightening order RONT P ssy ottom view 0 J-SX

41 ONTROL and MIX P ssemblies () Remove the all knobs. () Remove the ront panel by removing the screws. (0-HP00K--H) ront panel etachment/reattachment of the front panel or replacement of the ONTROL / P ssy or MIX P ssy, the front panel must be detached. The front panel is secured to the hassis ssy with double-back tape at locations for prevention of lifting. e fully careful not to deform the front panel when detaching it. bout the double-back tape that is used for securing the front panel and the hassis ssy When detaching the front panel The front panel and the hassis ssy are secured with pieces of double-back tape at the locations shown in the photo below. Slowly peel off the tape, taking care that you will not deform the front panel. When reattaching the front panel Neatly remove any residue of double-back tape from the back of the front panel and the hassis ssy. Stick pieces ( mm 0 mm) of NITTO No. 00 double-back tape to the locations shown in the photo below then remove the paper liner. Note: ven if double-back tape was not used in the initial state, be sure to attach double-back tape when reattaching the front panel. ouble-back tape ouble-back tape ouble-back tape: NITTO No. 00 ( mm 0 mm) ouble-back tape ouble-back tape J-SX

42 () Remove the nuts and washers. () Remove the 0 screws. ( H) 0 () Remove the screws (0-N-) () Remove the MI and isolation slices by removing the screws. (0-SL-0-H) ottom view MI isolation slice MI isolation slice () Remove the Isolation slice by removing the screws. (0-SL-0-H) Isolation slice ottom view () Remove the round plate by removing the screws. (0-SL-0-H) () isconnect the flexible cables and connectors. (N00 x, N0 x, N0 x) (0) Remove the solders. N0 N00 N0 N N0 N0 ottom view J-SX

43 () Remove the MIX P ssy by removing the screws. (0-SL-0-H) () Remove the ONTROL P ssy by removing the screws. (0-SL-0-H) () Remove the ONTROL P ssy by removing the screws. (0-SL-0-H) ONTROL P ssy MIX P ssy ottom view ONTROL P ssy Screw tightening order The other screws are random order. 0 0 TOUH P ssy () Remove the TOUH P ssemblies by removing the screws. ( H) TOUH P ssy TOUH P ssy ottom view J-SX

44 The pplication Position of dhesive and rease dhesive (YL00) JW L base dhesive (YL00) dhesive (YL00) SNSOR P ssy fixed plate dhesive (YL00) Sponge dhesive (YL00) H fader fixed plate dhesive (YL00) dhesive (YL00) Sensor fixed plate SNSOR P ssy MIX P ssy rease (M0) rease (M0) dhesive (YL00) US Jack SP P ssy hassis ssy dhesive (YL00) Washer rease (M0) Jog dial section ottom view J-SX

45 . H STTIN N JUSTMNT. NSSRY ITMS TO NOT fter repairing, be sure to check the version of the firmware, and if it is not the latest one, update to the latest version. Perform the each item when the following parts are replaced. I and P ssy storing firmware and utlity settings I, I, SP P ssy onfirmation of the version of the firmware Updating to the latest version of the firmware actory reset When replaced WHL ssy onfirmation of the specified value by the mode which measures Jog dial rotation time J-SX

46 . UPTIN O TH IRMWR What you need for updating Update file for J-SX * When the downloaded zip file is double-clicked, the update file is unzipped. xample) J-SX_V0.jar Updating procedures onnect the above prepared computer to J-SX via the US cable included with the product. adapter ( IN) J-SX_V0.jar computer where Java has been installed. * If Java has not been installed, please download the Java Runtime nvironment (JR) at: and install it on your computer. Please note that if you fail to update, turn on the power of J-SX again and start from Step of the above Updating Procedures. How to check the firmware version [or Windows] SIO driver exclusively for J-SX is required to be installed. rom the [Start menu], Run [ll the programs] [Pioneer] [J-SX] [J_SX Version isplay Utility] Pioneer_J-SX_Version/exe omputer (US) Turn on the power of J-SX while pressing the [SHIT] button and the [SYN] button on the LT deck ensure the Level meter Ls flash before releasing your finger from the these buttons. When the update file for J-SX (J-SX_Vxxx.jar) is activated, the following dialogue is displayed. lick the [Start] button. [or Mac] Open the pple menu while pressing the option key, then select System Profiler. The update of the firmware starts. Select the [US] from the [Hardware] to display the name of the controller. Select the controller to display the firmware version. When the firmware update process is complete, click the [OK] button. 0. J-SX

47 . ITMS OR WHIH USR STTINS R VILL This unit is provided with user settable items, as shown below. lthough no serious operational problems occur even if data for such user settable items are cleared during repair, it is recommended that you take note of those settings before starting repair. Use the heck Sheet, to which you can transcribe the settings. If the corresponding part or board ssy is replaced for repair, change the user resettable settings to those noted on the heck Sheet before starting repair. If resetting is not possible, when returning the repaired product, be sure to tell the customer that the Utility settings have been cleared and will have to be reset, as required. Item for Which User's Setting is vailable Setting Value (The factory default settings are indicated in bold.) Indication method MII controller setting utomatically switching modes, according to whether or not Serato J is running / orced operations to be generally expected from the MII controller, regardless of running or not running of Serato J Right eck HOT U mode button lit / ROLL mode button lit hannel fader start setting With SYN / without SYN / function disabled Left eck ffect parameter: button lit / button lit / button lit rossfader start setting With SYN / without SYN / function disabled Right eck ffect parameter: button lit / button lit / button lit ttenuator level setting for the Master output lashing setting in Slip mode Light/flash setting of the SLIP button 0 d (without attenuation) / d / d Left eck HOT U mode button lit / ROLL mode button lit / SLIR mode button lit lashing enable / lashing disenable Left eck SLIP button lit / SLIP button unlit The SLIP button to start flashing when Slip mode is entered / The SLIP button to light when Slip mode is entered and flash while normal playback is being performed in the background Right eck SLIP button lit / SLIP button unlit emo mode setting Time required for start of emo mode: One minute / minutes / 0 minutes of no operation / emo mode disabled Part Name ontent to be Stored Right eck LOOP X button lit / LOOP IN button lit / OOP OUT button lit / LOOP /X button lit Utility mode SMPLR VLOITY mode Velocity curve setting fter touch setting Operation setting for NL SRH pad urve / urve / urve / urve LOOP X button lit / LOOP IN button lit / OOP OUT button lit / LOOP /X button lit Setting enable / Setting disenable Left eck SMPLR mode button lit / SMPLR mode button unlit NL SRH pad operation to be limited / NL SRH pad operation NOT to be limited Left eck NSOR button lit / NSOR button unlit 0 (0. mm) / (0. mm) to ( mm) to (. mm) / (. mm) The number of lit segments of the [H] channel level indicator denotes a value in tens, and the number of lit segments of the [H] channel level indicator denotes a value in units. I (SP P ssy) Utility mode setting value ut lag setting for crossfader Microphone output setting to ooth monitor Illuminations mode setting for jog dial Setting for backspin length High-pass filter operation setting for microphone sound MII message operation setting for crossfader Jog dial touch sensor sensitivity adjustment White illuminations Red illuminations Microphone sound to be output from the [OOTH OUT] connector / Microphone sound NOT to be output from the [OOTH OUT] connector Right eck SMPLR mode button lit / SMPLR mode button unlit ecks and : Pattern / Pattern / Pattern / Pattern / Pattern, ecks and : Pattern / Pattern / Pattern / Pattern / Pattern Left eck Performance pad: lit / lit / lit / lit / lit, Right eck Performance pad: lit / lit / lit / lit / lit The red illuminations to be lit when the playback position of a track comes close to a hot cue point / the red illuminations to light or flash in the same way as the SLIP button Left eck Performance pad: lit / lit ackspin length: Short / Normal / Long Right eck Performance pad: lit / lit / lit nable / disable the high-pass filter for the microphone sound Left eck TP button lit / TP button unlit nable / disable optimization of MII messages for the crossfader Left eck KY LOK button lit / KY LOK button unlit / / + ( steps) The Ls at the center of the jog dial: ll unlit ( ) to half lit (0) to all lit (+) Jog dial touch sensor sensitivity adjustment J-SX

48 ach of the above items can be set in Utility mode or Jog ial Touch Sensor Sensitivity djustment mode. To enter Utility mode, disconnect the US cable from the P then press the STNY/ON switch on the rear panel of this unit to set it to Standby. Then while holding the SHIT and PLY/PUS buttons on the left deck pressed, press the STNY/ON switch to set it to ON. To start this unit in Jog ial Touch Sensor Sensitivity djustment mode, connect the P and this unit, using the supplied US cable, then while holding the SHIT button pressed, press the K or K button for the left jog dial or press the K or K button for the right jog dial. (or details, refer to the operating instructions of the unit.) Sheet for confirmation of the user setting MII controller setting hannel fader start setting uto ompulsion with SYN Without SYN isenable rossfader start setting with SYN Without SYN isenable ttenuator level setting for the Master output 0 d - d - d lashing setting in Slip mode nable isenable Light/flash setting of the SLIP button lashing Lit emo mode setting min min 0 min isenable Velocity curve setting urve urve urve urve fter touch setting nable isenable Operation setting for NL SRH pad Limit Non limit ut lag setting for crossfader 0 to to Microphone output setting to ooth monitor Output Non output Illuminations mode setting for jog dial White illuminations (Left deck) White illuminations (Right deck) Pattern Pattern Pattern Pattern Pattern Pattern Pattern Pattern Pattern Pattern Red illuminations Lit lashing Setting for backspin length Short Normal Long High-pass filter operation setting for microphone sound nable isenable MII message operation setting for crossfader nable isenable Jog dial touch sensor sensitivity adjustment J-SX

49 J-SX

50 . XPLO VIWS N PRTS LIST NOTS: - Parts marked by NSP are generally unavailable because they are not in our Master Spare Parts List. - The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. - Screws adjacent to b mark on product are used for disassembly. - or the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.). PKIN STION or or or or or or 0 J-SX

51 () PKIN STION PRTS LIST Mark No. escription Part No. Mark No. escription Part No. US able (L = 00 mm) 0-SU- Handle ase 00-SX-0 > dapter -SMK-0 Polyfoam 0-SX- > Power Plug See ontrast table () Polyfoam 0-SX- > Power Plug See ontrast table () Pasterboard 0-S--H > Power Plug See ontrast table () 0 ift ox See ontrast table () > Power Plug See ontrast table () > Power Plug See ontrast table () > Power Plug See ontrast table () > Power Plug See ontrast table () 0 Quick Start uide See ontrast table () Soft ag 0-JSX-0-H P ag (0*0mm, 0.0T) 0-JM0-0-H Quick Start uide See ontrast table () Quick Start uide See ontrast table () Quick Start uide See ontrast table () Quick Start uide See ontrast table () Handle 00-SX-0 () ONTRST TL J-SX/SVYX, UX, JKLPX and X are constructed the same except for the following: Mark No. Symbol and escription J-SX /SVYX J-SX /UX J-SX /JKLPX J-SX /X > Power Plug 0-JM0--H Not used 0-JM0- Not used > Power Plug 0-JM0-0 Not used 0-JM0-0 Not used > Power Plug Not used 0-JM0- Not used Not used > Power Plug Not used Not used 0-JM0--H Not used > Power Plug Not used Not used 0-JM0--H Not used > Power Plug Not used Not used 0-JM0-0 Not used > Power Plug Not used Not used Not used 0-JM0-0 0 Quick Start uide 0-JSXM- Not used Not used Not used (n, r, e, It, NI, s, Pt, Ru) Quick Start uide (n) Not used 0-JSXM- Not used Not used Quick Start uide (n, s, Ja) Not used Not used 0-JSXM- Not used Quick Start uide (Ko) Not used Not used 0-JSXM- Not used Quick Start uide (Zhcn) Not used Not used Not used 0-JSXM- 0 ift ox 0-SX-0 0-SX-0 0-SX-0 0-SX-0 J-SX

52 . XTRIOR STION K H I mm J-SX