FACT DATA 5-1 DUAL JK NEGATIVE EDGE-TRIGGERED FLIP-FLOP
|
|
- Clement O’Brien’
- 5 years ago
- Views:
Transcription
1 The MC112/T112 consists of o high-speed completely independent transition clocked flip-flops. The clocking operation is independent of rise and fall times of the clock waveform. The design allows operation as a D flip-flop (refer to MC74/T74 data sheet) by connecting the and inputs together. Asynchronous Inputs: LOW input to (Set) sets to HIGH level LOW input to (Clear) sets to LOW level Clear and Set are independent of clock Simultaneous LOW on and makes both and HIGH Outputs Source/Sink 24 ma ACT112 Has TTL Compatible Inputs DUAL NEGATIE EDGE-TRIGGERED FLIP-FLOP N SUFFIX CASE PLASTIC CC 16 CONNECTION DIAGRAM D SUFFIX CASE 751B-05 PLASTIC LOGIC SYMBOL GND 4 10 MODE SELECT TRUTH TABLE Operating Mode Inputs Outputs Set L H X X H L Reset (Clear) H L X X L H *Undetermined L L X X H H Toggle H H h h q q Load 0 (Reset) H H l h L H Load 1 (Set) H H h l H L Hold H H l l q q CC = PIN 16 GND = PIN *Both outputs will be HIGH while both S D and C D are LOW, but the output states are unpredictable if S D and C D go HIGH simultaneously. H, h = HIGH oltage Level L, l = LOW oltage Level X = Don t Care l, h (q) = Lower case letters indicate the state of the referenced input (or output) one set-up time prior to the HIGH to LOW clock transition. 5-1
2 MC112 MCT112 LOGIC DIAGRAM (one half shown) MAXIMUM RATINGS* alue CC DC Supply oltage (Referenced to GND) 0.5 to +7.0 in DC Input oltage (Referenced to GND) 0.5 to CC +0.5 out DC Output oltage (Referenced to GND) 0.5 to CC +0.5 Iin DC Input Current, per Pin ±20 ma Iout DC Output Sink/Source Current, per Pin ±50 ma ICC DC CC or GND Current per Output Pin ±50 ma Tstg Storage Temperature 65 to +150 C * Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. RECOMMENDED OPERATING CONDITIONS Min Max CC Supply oltage AC ACT in, out DC Input oltage, Output oltage (Ref. to GND) 0 CC Input Rise and Fall Time (Note 1) tr, r tff AC Devices except Schmitt Inputs tr, tf ns/ Input Rise and Fall Time (Note 2) ACT Devices except Schmitt Inputs T unction Temperature (PDIP) 140 C TA Operating Ambient Temperature Range C IOH Output Current High 24 ma IOL Output Current Low 24 ma 1. in from 30% to 70% CC ; see individual Data Sheets for devices that differ from the typical input rise and fall times. 2. in from 0.8 to 2.0 ; see individual Data Sheets for devices that differ from the typical input rise and fall times. ns/ 5-2
3 DC CHARACTERISTICS MC112 MCT112 CC () TA = 40 C Guaranteed Limits Conditions IH Minimum High Level OUT = 0.1 Input oltage or CC IL Maximum Low Level OUT = 0.1 Input oltage or CC OH Minimum High Level IOUT = 50 µa Output oltage *IN = IL or IH ma IOH 24 ma ma OL Maximum Low Level IOUT = 50 µa Output oltage IIN IOLD IOHD ICC Maximum Input Leakage Current Minimum Dynamic Output Current Maximum uiescent Supply Current *IN = IL or IH ma IOL 24 ma ma 5.5 ±0.1 ±1.0 µa I = CC, GND ma OLD = 1.65 Max ma OHD = 3.85 Min µa IN = CC or GND * All outputs loaded; thresholds on input associated with output under test. Maximum test duration 2.0 ms, one output loaded at a time. Note: I IN and I 3.0 are guaranteed to be less than or equal to the respective 5.5 CC. AC CHARACTERISTICS (For Figures and Waveforms See Section 3) CC* () Min Max Min Max Maximum Clock fmax Frequency tplh n to n or n tphl n to n or n tplh n or n to n or n tphl n or n to n or n MHz 3-3 * oltage Range 3.3 is 3.3 ±0.3. oltage Range 5.0 is 5.0 ±
4 MC112 MCT112 AC OPERATING REUIREMENTS ts th trec CC* () Guaranteed Minimum Set-up Time, HIGH or LOW n or n to n Hold Time, HIGH or LOW n or n to n Pulse Width n Pulse Width n or n Recovery Time n or n to * oltage Range 3.3 is 3.3 ±0.3. oltage Range 5.0 is 5.0 ±0.5. ns 3-9 ns 3-9 ns 3-9 DC CHARACTERISTICS CC () T T TA = 40 C Guaranteed Limits IH Minimum High Level Input oltage IL Maximum Low Level Input oltage OH Minimum High Level Output oltage Conditions OUT = 0.1 or CC 0.1 OUT = 0.1 or CC 0.1 IOUT = 50 µa OL Maximum Low Level Output oltage *IN = IL or IH 24 ma IOH 24 ma IOUT = 50 µa IIN Maximum Input Leakage Current *IN = IL or IH ma IOL 24 ma 5.5 ±0.1 ±1.0 µa I = CC, GND ICCT Additional Max. ICC/Input ma I = CC 2.1 IOLD IOHD ICC Minimum Dynamic Output Current Maximum uiescent Supply Current ma OLD = 1.65 Max ma OHD = 3.85 Min µa IN = CC or GND * All outputs loaded; thresholds on input associated with output under test. Maximum test duration 2.0 ms, one output loaded at a time. 5-4
5 MC112 MCT112 AC CHARACTERISTICS (For Figures and Waveforms See Section 3) fmax tplh tphl tplh tphl Maximum Clock Frequency n to n or n n to n or n n or n to n or n n or n to n or n * oltage Range 5.0 is 5.0 ±0.5. CC* () T T Min Max Min Max MHz AC OPERATING REUIREMENTS ts Set-up Time, HIGH or LOW n or n to n th Hold Time, HIGH or LOW n or n to n Pulse Width n Pulse Width n or n trec Recovery TIme n or n to * oltage Range 5.0 is 5.0 ±0.5. CC* () T T Guaranteed Minimum ns ns ns 3-9 CAPACITANCE alue Test Conditions CIN Input Capacitance 4.5 pf CC = 5.0 D Power Dissipation Capacitance 35 pf CC =
6 MC112 MCT112 OUTLINE DIMENSIONS 16 A 1 8 H G F 9 D 16 PL B S C 0.25 (0.010) M T SEATING T PLANE A M N SUFFIX PLASTIC DIP PACAGE CASE ISSUE R L M NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. INCHES MILLIMETERS DIM MIN MAX MIN MAX A B C D F G BSC 2.54 BSC H BSC 1.27 BSC L M S T SEATING PLANE G A D 16 PL B D SUFFIX PLASTIC SOIC PACAGE CASE 751B 05 ISSUE P 8 PL 0.25 (0.010) M B S C 0.25 (0.010) M T B S A S M R X 45 F NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. MILLIMETERS INCHES DIM MIN MAX MIN MAX A B C D F G 1.27 BSC BSC M P R Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. ical parameters can and do vary in different applications. All operating parameters, including icals must be validated for each customer application by customer s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE: Motorola Literature Distribution; APAN: Nippon Motorola Ltd.; Tatsumi SPD LDC, Toshikatsu Otsuki, P.O. Box 20912; Phoenix, Arizona F Seibu Butsuryu Center, Tatsumi oto u, Tokyo 135, apan MFAX: RMFAX0@ .sps.mot.com TOUCHTONE (602) HONG ONG: Motorola Semiconductors H.. Ltd.; 8B Tai Ping Industrial Park, INTERNET: NET.com 51 Ting ok Road, Tai Po, N.T., Hong ong MC112/D
FACT DATA 5-1 DUAL JK NEGATIVE EDGE-TRIGGERED FLIP-FLOP
The MC113/T113 consists of o high-speed completely independent transition clocked flip-flops. The clocking operation is independent of rise and fall times of the clock waveform. The design allows operation
More informationFigure 1. Pinout: 16 Lead Packages Conductors (Top View) ORDERING INFORMATION Figure 2. Logic Symbol PIN ASSIGNMENT
The MC74AC138/74ACT138 is a high speed 1 of 8 decoder/demultiplexer. This device is ideally suited for high speed bipolar memory chip select address decoding. The multiple input enables allow parallel
More informationSchmitt Trigger Inputs Outputs Source/Sink 24 ma ACT132 Has TTL Compatible Inputs. ORDERING INFORMATION
The MC74AC/74ACT132 contains four 2 input NAND gates which are capable of transforming slowly changing input signals into sharply defined, jitter free output signals. In addition, they have greater noise
More informationMC74AC109, MC74ACT109. Dual JK Positive Edge Triggered Flip Flop
MC9, MC9 Dual JK Positive EdgeTriggered FlipFlop The MC9/9 coists of two highspeed completely independent traition clocked JK flipflops. The clocking operation is independent of rise and fall times of
More informationLOW POWER SCHOTTKY. GUARANTEED OPERATING RANGES ORDERING INFORMATION PLASTIC N SUFFIX CASE 648
The SN74LS194A is a High Speed 4-Bit Bidirectional Universal Shift Register. As a high speed multifunctional sequential building block, it is useful in a wide variety of applications. It may be used in
More informationMC74AC138, MC74ACT of 8 Decoder/Demultiplexer
1 of 8 Decoder/Demultiplexer The MC74AC138/74ACT138 is a high speed 1 of 8 decoder/demultiplexer. This device is ideally suited for high speed bipolar memory chip select address decoding. The multiple
More informationSN74LS157MEL. Quad 2 Input Multiplexer LOW POWER SCHOTTKY
Quad 2 Input Multiplexer The LSTTL/ MSI is a high speed Quad 2-Input Multiplexer. Four bits of data from two sources can be selected using the common Select and Enable inputs. The four buffered outputs
More informationSN74LS145MEL. 1 of 10 Decoder/Driver Open Collector LOW POWER SCHOTTKY
of 0 Decoder/Driver Open Collector The SN74LS45, -of-0 Decoder/Driver, is designed to accept BCD inputs and provide appropriate outputs to drive 0-digit incandescent displays. All outputs remain off for
More informationLOW POWER SCHOTTKY. ESD > 3500 Volts. GUARANTEED OPERATING RANGES ORDERING INFORMATION V CC 8 7 GND
ESD > 3500 Volts V CC 8 4 3 2 0 9 LOW POWER SCHOTTKY 2 3 4 5 6 7 GND GUARANTEED OPERATING RANGES Symbol Parameter Min Typ Max Unit V CC Supply Voltage 4.75 5.0 5.25 V T A Operating Ambient Temperature
More informationMC74AC132, MC74ACT132. Quad 2 Input NAND Schmitt Trigger
MC74AC32, MC74ACT32 Quad 2 Input NAND Schmitt Trigger The MC74AC/74ACT32 contains four 2 input NAND gates which are capable of transforming slowly changing input signals into sharply defined, jitter free
More informationSN74LS132MEL. Quad 2 Input Schmitt Trigger NAND Gate LOW POWER SCHOTTKY
Quad 2 Input Schmitt Trigger NAND Gate The SN74LS32 contains four 2-Input NAND Gates which accept standard TTL input signals and provide standard TTL output levels. They are capable of transforming slowly
More informationNE522 High Speed Dual Differential Comparator/Sense Amp
HighSpeed DualDifferential Comparator/Sense Amp Features 5 ns Maximum Guaranteed Propagation Delay 0 A Maximum Input Bias Current TTL-Compatible Strobes and Outputs Large Common-Mode Input oltage Range
More informationSN54/74LS145 1-OF-10 DECODER/DRIVER OPEN-COLLECTOR 1-OF-10 DECODER/ DRIVER OPEN-COLLECTOR FAST AND LS TTL DATA 5-240
-OF-0 DECODER/DRIVER OPEN-COLLECTOR The SN54 / 74LS45, -of-0 Decoder/Driver, is designed to accept BCD inputs and provide appropriate outputs to drive 0-digit incandescent displays. All outputs remain
More informationLOW POWER SCHOTTKY. GUARANTEED OPERATING RANGES ORDERING INFORMATION
These dc triggered multivibrators feature pulse width control by three methods. The basic pulse width is programmed by selection of external resistance and capacitance values. The LS22 has an internal
More informationSN74LS151MEL. 8 Input Multiplexer LOW POWER SCHOTTKY
8 Input Multiplexer The TTL/MSI SN74LS5 is a high speed 8-input Digital Multiplexer. It provides, in one package, the ability to select one bit of data from up to eight sources. The LS5 can be used as
More informationSN74LS175MEL. Quad D Flip Flop LOW POWER SCHOTTKY
uad Flip Flop The LSTTL/MSI SN74LS75 is a high speed uad Flip-Flop. The device is useful for general flip-flop requirements where clock and clear inputs are common. The information on the inputs is stored
More informationMC74AC161, MC74ACT161, MC74AC163, MC74ACT163. Synchronous Presettable Binary Counter
MC74AC161, MC74ACT161, MC74AC163, MC74ACT163 Synchronous Presettable Binary Counter The MC74AC161/74ACT161 and MC74AC163/74ACT163 are high speed synchronous modulo 16 binary counters. They are synchronously
More informationMC74AC259, MC74ACT Bit Addressable Latch
8 Bit Addressable Latch The MC74AC259/74ACT259 is a high speed 8 bit addressable latch designed for general purpose storage applicatio in digital systems. It is a multifunctional device capable of storing
More informationSN74LS147, SN74LS Line to 4 Line and 8 Line to 3 Line Priority Encoders LOW POWER SCHOTTKY
0 Line to Line and 8 Line to 3 Line Priority Encoders The SN7LS7 and the SN7LS8 are Priority Encoders. They provide priority decoding of the inputs to eure that only the highest order data line is encoded.
More informationHigh Performance Silicon Gate CMOS
SEIONDUTOR TEHNIAL DATA High Performance Silicon Gate OS The 5/7H32A is identical in pinout to the LS32. The device inputs are compatible with standard OS outputs; with pullup resistors, they are compatible
More informationMC74AC74, MC74ACT74. Dual D Type Positive Edge Triggered Flip Flop
Dual D Type Positive Edge Triggered Flip Flop The MC74AC74/74ACT74 is a dual D type flip flop with Asynchronous Clear and Set inputs and complementary (Q,Q) outputs. Information at the input is traferred
More informationLOW POWER SCHOTTKY. MODE SELECT TRUTH TABLE ORDERING INFORMATION GUARANTEED OPERATING RANGES OPERATING MODE
The SN74S74A dual edge-triggered flip-flop utilizes Schottky TT circuitry to produce high speed D-type flip-flops. Each flip-flop has individual clear and set inputs, and also complementary and outputs.
More informationLOW POWER SCHOTTKY. GUARANTEED OPERATING RANGES ORDERING INFORMATION PLASTIC N SUFFIX CASE 648
The SN74LS247 is a BCD-to-Seven-Segment Decoder/Drivers. The LS247 composes the and with the tails. The LS247 has active-low outputs for direct drive of indicators. The LS247 features a lamp test input
More informationMC Bit Magnitude Comparator
Bit Magnitude Comparator The MC0 is a high speed expandable bit comparator for comparing the magnitude of two binary words. Two outputs are provided: and. A = B can be obtained by NORing the two outputs
More information74LS195 SN74LS195AD LOW POWER SCHOTTKY
The SN74LS95A is a high speed 4-Bit Shift Register offering typical shift frequencies of 39 MHz. It is useful for a wide variety of register and counting applications. It utilizes the Schottky diode clamped
More informationSN74LS125A, SN74LS126A. Quad 3 State Buffers LOW POWER SCHOTTKY. LS125A LS126A TRUTH TABLES ORDERING INFORMATION
Quad 3 State Buffers V CC E D O E D O 4 3 2 0 9 8 LOW POWER SCHOTTKY 2 3 4 5 6 E D O E D O LS25A GND V CC E D O E D O 4 3 2 0 9 8 4 PLASTIC N SUFFIX CASE 646 LS25A INPUTS 2 3 4 5 6 E D O E LS26A D O GND
More informationMC3346. General Purpose Transistor Array One Differentially Connected Pair and Three Isolated Transistor Arrays
General Purpose Transistor Array One Differentially Connected Pair and Three Isolated Transistor Arrays The MC336 is designed for general purpose, low power applications for consumer and industrial designs.
More informationSN74LS74AMEL LOW POWER SCHOTTKY
The SN74S74A dual edge-triggered flip-flop utilizes Schottky TT circuitry to produce high speed D-type flip-flops. Each flip-flop has individual clear and set inputs, and also complementary Q and Q outputs.
More informationMC74HC132A. Quad 2 Input NAND Gate with Schmitt Trigger Inputs. High Performance Silicon Gate CMOS
Quad 2 Input NAND Gate with Schmitt Trigger Inputs High Performance Silicon Gate CMOS The is identical in pinout to the LS32. The device inputs are compatible with standard CMOS outputs; with pull up resistors,
More informationMC74ACT Input Universal Shift/Storage Register with Synchronous Reset and Common I/O Pins
8 Input Universal Shift/Storage Register with Synchronous Reset and Common I/O Pins The MC74ACT323 is an 8-bit universal shift/storage register with3-state outputs. Its function is similar to the MC74ACT299
More informationNLSV2T Bit Dual-Supply Inverting Level Translator
2-Bit Dual-Supply Inverting Level Translator The NLSV2T240 is a 2 bit configurable dual supply voltage level translator. The input A n and output B n ports are designed to track two different power supply
More informationSN74LS157MEL LOW POWER SCHOTTKY
The LSTTL/MSI SN74LS157 is a high speed Quad 2-Input Multiplexer. Four bits of data from two sources can be selected using the common Select and Enable inputs. The four buffered outputs present the selected
More informationSN74LS373, SN74LS374. Octal Transparent Latch with 3 State Outputs; Octal D Type Flip Flop with 3 State Output LOW POWER SCHOTTKY
Octal Transparent Latch with 3 State Outputs; Octal Type Flip Flop with 3 State Output The SN74LS373 consists of eight latches with 3-state outputs for bus organized system applications. The flip-flops
More information74AC00, 74ACT00 Quad 2-Input NAND Gate
74AC00, 74ACT00 Quad 2-Input NAND Gate Features I CC reduced by 50% Outputs source/sink 24mA ACT00 has TTL-compatible inputs Ordering Information Order Number Package Number General Description The AC00/ACT00
More informationLOW POWER SCHOTTKY. MARKING DIAGRAMS GUARANTEED OPERATING RANGES ORDERING INFORMATION. SN74LS37xN AWLYYWW PDIP 20 N SUFFIX CASE 738
The SN74LS373 consists of eight latches with 3-state outputs for bus organized system applications. The flip-flops appear transparent to the data (data changes asynchronously) when Latch Enable (LE) is
More informationCONNECTION DIAGRAM (TOP VIEW) 20. Note: Pin 1 is marked for orientation. Symbol Parameter Min Typ Max Unit VCC Supply Voltage 54 74
FOUR-BIT UP/DOWN COUNTER WITH THREE-STATE OUTPUTS The SN54/ LS569A is designed as programmable up/down BCD and Binary counters respectively. These devices have 3-state outputs for use in bus organized
More informationMARKING DIAGRAMS 16 LOGIC DIAGRAM DIP PIN ASSIGNMENT CLOCKED TRUTH TABLE ORDERING INFORMATION CDIP 16 L SUFFIX CASE 620
The MC06 contains six high speed, master slave type D flip flops. Clocking is common to all six flip flops. Data is entered into the master when the clock is low. Master to slave data transfer takes place
More informationMC74VHC132. Quad 2 Input NAND Schmitt Trigger
MC74HC32 Quad 2 Input NAND Schmitt Trigger The MC74HC32 is an advanced high speed CMOS Schmitt NAND trigger fabricated with silicon gate CMOS technology. It achieves high speed operation similar to equivalent
More informationMC74AC259, MC74ACT Bit Addressable Latch
8-Bit Addressable Latch The MC259/T259 is a high speed 8 bit addressable latch designed for general purpose storage applicatio in digital systems. It is a multifunctional device capable of storing single
More information74HC of 8 Decoder/ Demultiplexer. High Performance Silicon Gate CMOS
of 8 Decoder/ Demultiplexer High Performance Silicon Gate CMOS The 74HC38 is identical in pinout to the LS38. The device inputs are compatible with standard CMOS outputs; with pullup resistors, they are
More informationMARKING DIAGRAMS 16 LOGIC DIAGRAM DIP PIN ASSIGNMENT CLOCKED TRUTH TABLE ORDERING INFORMATION CDIP 16 L SUFFIX CASE 620
The MC10176 contains six high-speed, master slave type D flip-flops. Clocking is common to all six flip-flops. Data is entered into the master when the clock is low. Master to slave data transfer takes
More informationSEMICONDUCTOR TECHNICAL DATA
SEMIONDUTOR TEHNIAL DATA The M4532B is cotructed with complementary MOS (MOS) enhancement mode devices. The primary function of a priority encoder is to provide a binary address for the active input with
More informationMARKING DIAGRAMS LOGIC DIAGRAM DIP PIN ASSIGNMENT ORDERING INFORMATION CDIP 16 L SUFFIX CASE 620 MC10138L AWLYYWW
The MC101 is a four bit counter capable of divide by two, five, or ten functions. It is composed of four set reset master slave flip flops. Clock inputs trigger on the positive going edge of the clock
More informationSN54/74LS147 SN54/74LS148 SN54/74LS LINE-TO-4-LINE AND 8-LINE-TO-3-LINE PRIORITY ENCODERS
10-LINE-TO-4-LINE AND 8-LINE-TO-3-LINE PRIORITY ENCODERS The SN54/ 74LS147 and the SN54/ 74LS148 are Priority Encoders. They provide priority decoding of the inputs to eure that only the highest order
More informationMC74LCX74. Low-Voltage CMOS Dual D-Type Flip-Flop. With 5 V Tolerant Inputs
Low-oltage CMOS Dual D-Type Flip-Flop With 5 Tolerant Inputs The MC74LCX74 is a high performance, dual D type flip flop with asynchronous clear and set inputs and complementary (O, O) outputs. It operates
More informationMC74VHC14. Hex Schmitt Inverter
MC74HC4 Hex Schmitt Inverter The MC74HC4 is an advanced high speed CMOS Schmitt inverter fabricated with silicon gate CMOS technology. It achieves high speed operation similar to equivalent Bipolar Schottky
More informationIs Now Part of To learn more about ON Semiconductor, please visit our website at
Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC
More informationSN74LS166MEL. 8 Bit Shift Registers LOW POWER SCHOTTKY
8 Bit Shift Registers The SN74S166 is an 8-Bit Shift Register. Designed with all inputs buffered, the drive requirements are lowered to one 74S standard load. By utilizing input clamping diodes, switching
More informationLOW POWER SCHOTTKY. GUARANTEED OPERATING RANGES ORDERING INFORMATION PLASTIC N SUFFIX CASE 648
The SN74LS247 is a BCD-to-Seven-Segment Decoder/Drivers. The LS247 composes the and with the tails. The LS247 has active-low outputs for direct drive of indicators. The LS247 features a lamp test input
More information74HC74. Dual D Flip Flop with Set and Reset. High Performance Silicon Gate CMOS
Dual D Flip Flop with Set and Reset High Performance Silicon Gate CMOS The 74HC74 is identical in pinout to the LS74. The device inputs are compatible with standard CMOS outputs; with pullup resistors,
More informationLOW POWER SCHOTTKY. GUARANTEED OPERATING RANGES ORDERING INFORMATION
The LSTTL/MSI SN74LS18 is a high speed 1-of-8 Decoder/ Demultiplexer. This device is ideally suited for high speed bipolar memory chip select address decoding. The multiple input enables allow parallel
More information74HCT245. Octal 3-State Noninverting Bus Transceiver with LSTTL-Compatible Inputs. High-Performance Silicon-Gate CMOS
Octal 3-State Noninverting Bus Transceiver with LSTTL-Compatible Inputs High-Performance Silicon-Gate CMOS The 74HCT245 is identical in pinout to LS245. The device has TTL-Compatible Inputs. The HCT245
More informationSEMICONDUCTOR TECHNICAL DATA
SEICONDUCTOR TECHNICAL DATA The is a COS look ahead carry generator capable of anticipating a carry across four binary adders or groups of adders. The device is cascadable to perform full look ahead across
More informationMARKING DIAGRAMS DIP PIN ASSIGNMENT ORDERING INFORMATION FUNCTION TABLE CDIP 16 L SUFFIX CASE 620 MC10136L AWLYYWW
The MC16 is a high speed synchronous counter that can count up, count down, preset, or stop count at frequencies exceeding 1 MHz. The flexibility of this device allows the designer to use one basic counter
More informationMARKING DIAGRAMS 16 LOGIC DIAGRAM DIP PIN ASSIGNMENT TRUTH TABLE ORDERING INFORMATION CDIP 16 L SUFFIX CASE 620 MC10173L AWLYYWW
The MC03 is a quad two channel multiplexer with latch. It incorporates common clock and common data select inputs. The select input determines which data input is enabled. A high (H) level enables data
More informationNTJD4105C. Small Signal MOSFET. 20 V / 8.0 V, Complementary, A / A, SC 88
NTJD5C Small Signal MOSFET V / 8. V, Complementary, +.63 A /.775 A, SC 88 Features Complementary N and P Channel Device Leading 8. V Trench for Low R DS(on) Performance ESD Protected Gate ESD Rating: Class
More informationThe MC10107 is a triple 2 input exclusive OR/NOR gate. P D = 40 mw typ/gate (No Load) t pd = 2.8 ns typ t r, t f = 2.
The MC10107 is a triple input exclusive OR/NOR gate. P D = 0 mw typ/gate (No Load) t pd =. ns typ t r, t f =. ns typ (0% 0%) LOGIC DIAGRAM MARKING DIAGRAMS CDIP 16 L SUFFIX CASE 60 16 1 MC10107L AWLYYWW
More informationSN74LS42MEL. One of Ten Decoder LOW POWER SCHOTTKY
SN74S42 One of Ten Decoder The STT/ MSI SN74S42 is a Multipurpose Decoder designed to accept four BCD inputs and provide ten mutually exclusive outputs. The S42 is fabricated with the Schottky barrier
More informationSN74LS138MEL LOW POWER SCHOTTKY
The LSTTL/MSI SN74LS18 is a high speed 1-of-8 Decoder/ Demultiplexer. This device is ideally suited for high speed bipolar memory chip select address decoding. The multiple input enables allow parallel
More informationDual D Flip-Flop with Set and Reset High-Speed Silicon-Gate CMOS
TECHNICAL DATA IN74ACT74 Dual D Flip-Flop with Set and Reset High-Speed Silicon-Gate CMOS The IN74ACT74 is identical in pinout to the LS/ALS74, HC/HCT74. The IN74ACT74 may be used as a level converter
More informationIs Now Part of To learn more about ON Semiconductor, please visit our website at
Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC
More informationNLSV22T244. Dual 2-Bit Dual-Supply Non-Inverting Level Translator
Dual 2-Bit Dual-Supply Non-Inverting Level Translator The NLSV22T244 is a dual 2 bit configurable dual supply bus buffer level translator. The input ports A and the output ports B are designed to track
More informationNGTG50N60FLWG IGBT. 50 A, 600 V V CEsat = 1.65 V
NGTGN6FLWG IGBT This Insulated Gate Bipolar Transistor (IGBT) features a robust and cost effective Trench construction, and provides superior performance in demanding switching applications, offering both
More informationV N (8) V N (7) V N (6) GND (5)
4-Channel Low Capacitance Dual-Voltage ESD Protection Array Features Three Channels of Low Voltage ESD Protection One Channel of High Voltage ESD Protection Provides ESD Protection to IEC61000 4 2 Level
More informationMC74HCT138A. 1 of 8 Decoder/ Demultiplexer with LSTTL Compatible Inputs. High Performance Silicon Gate CMOS
of 8 Decoder/ Demultiplexer with LSTTL Compatible Inputs High Performance Silicon Gate CMOS The MC74HCT38A is identical in pinout to the LS38. The HCT38A may be used as a level converter for interfacing
More informationMC14070B, MC14077B CMOS SSI. Quad Exclusive OR and NOR Gates
C070B, C077B COS SSI Quad Exclusive OR and NOR Gates The C070B quad exclusive OR gate and the C077B quad exclusive NOR gate are constructed with OS Pchannel and Nchannel enhancement mode devices in a single
More informationMC74HC139A. Dual 1 of 4 Decoder/ Demultiplexer. High Performance Silicon Gate CMOS
MC74HC39A Dual of 4 Decoder/ Demultiplexer High Performance Silicon Gate CMOS The MC74HC39A is identical in pinout to the LS39. The device inputs are compatible with standard CMOS outputs; with pull up
More informationBAS19LT1G, BAS20LT1G, BAS21LT1G, BAS21DW5T1G. High Voltage Switching Diode HIGH VOLTAGE SWITCHING DIODE
BAS9LTG, BAS20LTG, BAS2LTG, BAS2DWTG High Voltage Switching Diode Features These Devices are PbFree, Halogen Free/BFR Free and are RoHS Compliant MAXIMUM RATINGS Continuous Reverse Voltage Rating Symbol
More informationLOW POWER SCHOTTKY. GUARANTEED OPERATING RANGES ORDERING INFORMATION
The SN74S240 and SN74S244 are Octal Buffers and ine Drivers designed to be employed as memory address drivers, clock drivers and bus-oriented transmitters/receivers which provide improved PC board density.
More informationMC74AC74, MC74ACT74. Dual D Type Positive Edge Triggered Flip Flop
Dual D Type Positive Edge Triggered Flip Flop The MC74/T74 is a dual D type flip flop with Asynchronous Clear and Set inputs and complementary (Q,Q) outputs. Information at the input is traferred to the
More informationMC74HC244A Octal 3 State Noninverting Buffer/Line Driver/ Line Receiver
Octal 3 State Noninverting Buffer/Line Driver/ Line Receiver High Performance Silicon Gate CMOS The MC74HC244A is identical in pinout to the LS244. The device inputs are compatible with standard CMOS outputs;
More informationSN74LS85MEL LOW POWER SCHOTTKY
The SN74LS85 is a 4-Bit Magnitude Camparator which compares two 4-bit words (A, B), each word having four Parallel Inputs (A0 A3, B0 B3); A3, B3 being the most significant inputs. Operation is not restricted
More informationMARKING DIAGRAMS LOGIC DIAGRAM DIP PIN ASSIGNMENT TRUTH TABLE ORDERING INFORMATION CDIP 16 L SUFFIX CASE 620 MC10161L AWLYYWW
The MC10161 is designed to decode a three bit input word to a one of eight line output. The selected output will be low while all other outputs will be high. The enable inputs, when either or both are
More informationNDF08N50Z, NDP08N50Z. N-Channel Power MOSFET. Low ON Resistance Low Gate Charge 100% Avalanche Tested These Devices are Pb Free and are RoHS Compliant
N-Channel Power MOSFET 500 V, 0.69 Features Low ON Resistance Low Gate Charge 0% Avalanche Tested These Devices are Pb Free and are RoHS Compliant ABSOLUTE MAXIMUM RATINGS (T C = 25 C unless otherwise
More informationMC1403, B. Low Voltage Reference PRECISION LOW VOLTAGE REFERENCE
Low Voltage Reference A precision bandgap voltage reference designed for critical instrumentation and D/A converter applications. This unit is designed to work with D/A converters, up to bits in accuracy,
More informationNGTB40N60FLWG IGBT. 40 A, 600 V V CEsat = 1.85 V
NGTB4N6FLWG IGBT This Insulated Gate Bipolar Transistor (IGBT) features a robust and cost effective Trench construction, and provides superior performance in demanding switching applications, offering
More informationMC74HCT573A/D. Octal 3-State Noninverting Transparent Latch with LSTTL Compatible Inputs. High Performance Silicon Gate CMOS
Octal 3-State Noninverting Transparent Latch with LSTTL Compatible Inputs High Performance Silicon Gate CMOS The MC74HCT573A is identical in pinout to the LS573. This device may be used as a level converter
More information74VHC08 Quad 2-Input AND Gate
74VHC08 Quad 2-Input AND Gate Features High Speed: t PD = 4.3ns (Typ.) at T A = 25 C High noise immunity: V NIH = V NIL = 28% V CC (Min.) Power down protection is provided on all inputs Low power dissipation:
More informationMC74LV594A. 8-Bit Shift Register with Output Register
8-Bit Shift Register with Output Register The MC74LV594A is an 8 bit shift register designed for 2 V to 6.0 V V CC operation. The device contain an 8 bit serial in, parallel out shift register that feeds
More informationSN74LS153D 74LS153 LOW POWER SCHOTTKY
74LS153 The LSTTL/MSI SN74LS153 is a very high speed Dual 4-Input Multiplexer with common select inputs and individual enable inputs for each section. It can select two bits of data from four sources.
More informationMC14584B. Hex Schmitt Trigger
MC4584B Hex Schmitt Trigger The MC4584B Hex Schmitt Trigger is constructed with MOS Pchannel and Nchannel enhancement mode devices in a single monolithic structure. These devices find primary use where
More information74HC244 Octal 3 State Noninverting Buffer/Line Driver/ Line Receiver
Octal 3 State Noninverting Buffer/Line Driver/ Line Receiver High Performance Silicon Gate CMOS The is identical in pinout to the LS244. The device inputs are compatible with standard CMOS outputs; with
More informationNL27WZ14. Dual Schmitt Trigger Inverter
N7WZ Dual Schmitt Trigger Inverter The N7WZ is a high performance dual inverter with Schmitt Trigger inputs operating from a.5 to supply. Pin configuration and function are the same as the N7WZ0, but the
More informationFST Bit Bus Switch
FST32 4-Bit Bus Switch The ON Semiconductor FST32 is a quad, high performance switch. The device is CMOS TTL compatible when operating between 4 and. Volts. The device exhibits extremely low R ON and adds
More informationMC74HC138A. 1-of-8 Decoder/ Demultiplexer. High Performance Silicon Gate CMOS
MC74HC38A -of-8 Decoder/ Demultiplexer High Performance Silicon Gate CMOS The MC74HC38A is identical in pinout to the LS38. The device inputs are compatible with standard CMOS outputs; with pullup resistors,
More information1PMT5920B Series. 3.2 Watt Plastic Surface Mount POWERMITE Package PLASTIC SURFACE MOUNT 3.2 WATT ZENER DIODES VOLTS
PMT90B Series. Watt Plastic Surface Mount POWERMITE Package This complete new line of. Watt Zener Diodes are offered in highly efficient micro miniature, space saving surface mount with its unique heat
More informationNGTB25N120LWG IGBT. 25 A, 1200 V V CEsat = 1.85 V E off = 0.8 mj
NGTBNLWG IGBT This Insulated Gate Bipolar Transistor (IGBT) features a robust and cost effective Field Stop (FS) Trench construction, and provides superior performance in demanding switching applications.
More information74FST Bit Bus Switch
4FST32 4 Bit Bus Switch The ON Semiconductor 4FST32 is a quad, high performance switch. The device is CMOS TTL compatible when operating between 4 and. Volts. The device exhibits extremely low R ON and
More informationMC14049B, MC14050B. Hex Buffer
MC4049B, MC4050B Hex Buffer The MC4049B Hex Inverter/Buffer and MC4050B Noninverting Hex Buffer are constructed with MOS PChannel and NChannel enhancement mode devices in a single monolithic structure.
More informationMMBZ5221BLT1 Series. Zener Voltage Regulators. 225 mw SOT 23 Surface Mount
MMBZ5BLT Series Zener Voltage Regulators 5 mw SOT Surface Mount This series of Zener diodes is offered in the convenient, surface mount plastic SOT package. These devices are designed to provide voltage
More informationMUR3020PTG SUR83020PTG MUR3040PTG MUR3060PTG SUR83060PTG. SWITCHMODE Power Rectifiers ULTRAFAST RECTIFIERS 30 AMPERES, VOLTS
MUR00PTG, SUR00PTG, MUR00PTG, MUR00PTG, SUR00PTG SWITCHMODE Power Rectifiers These state of the art devices are designed for use in switching power supplies, inverters and as free wheeling diodes. Features
More informationMMBZ5221BLT1 Series. Zener Voltage Regulators. 225 mw SOT 23 Surface Mount
MMBZ5BLT Series Preferred Device Zener Voltage Regulators 5 mw SOT Surface Mount This series of Zener diodes is offered in the convenient, surface mount plastic SOT package. These devices are designed
More informationNGTG25N120FL2WG. IGBT - Field Stop II. 25 A, 1200 V V CEsat = 2.0 V E off = 0.60 mj
NGTGNFLWG IGBT - Field Stop II This Insulated Gate Bipolar Transistor (IGBT) features a robust and cost effective Field Stop II Trench construction, and provides superior performance in demanding switching
More informationNGTB30N120LWG IGBT. 30 A, 1200 V V CEsat = 1.75 V E off = 1.0 mj
NGTBNLWG IGBT This Insulated Gate Bipolar Transistor (IGBT) features a robust and cost effective Field Stop (FS) Trench construction, and provides superior performance in demanding switching applications.
More informationSEMICONDUCTOR TECHNICAL DATA
SEICONDUCTOR TECHNICL DT The C7 is a static clocked serial shift register whose length may be programmed to be any number of bits between and. The number of bits selected is equal to the sum of the subscripts
More informationMC74LCX138MEL. With 5 V Tolerant Inputs
With 5 V Tolerant Inputs The MC74LCX38 is a high performance, 3 to 8 decoder/demultiplexer operating from a 2.3 to 3.6 V supply. High impedance TTL compatible inputs significantly reduce current loading
More information74HC245. Octal 3 State Noninverting Bus Transceiver. High Performance Silicon Gate CMOS
Octal 3 State Noninverting Bus Traceiver High Performance Silicon Gate CMOS The 74HC245 is identical in pinout to the LS245. The device inputs are compatible with standard CMOS outputs; with pull up resistors,
More informationNL17SV16. Ultra-Low Voltage Buffer
N7S6 Ultra-ow oltage Buffer The N7S6X5T is an ultra high performance single Buffer fabricated in sub micron silicon gate 0.35 m technology with excellent performance down to 0.9. This device is ideal for
More information2N5401. PNP Silicon. These are Pb Free Devices* Features. MAXIMUM RATINGS THERMAL CHARACTERISTICS MARKING DIAGRAM
Preferred Device Amplifier Transistors PNP Silicon Features These are PbFree Devices* MAXIMUM RATINGS Rating Symbol alue Unit Collector Emitter oltage CEO 1 Collector Base oltage CBO 16 Emitter Base oltage
More informationMJW18020G. NPN Silicon Power Transistors High Voltage Planar 30 AMPERES 1000 VOLTS BV CES 450 VOLTS BV CEO, 250 WATTS
NPN Silicon Power Transistors High Voltage Planar The MJW18020 planar High Voltage Power Transistor is specifically Designed for motor control applications, high power supplies and UPS s for which the
More information