Valve Selection Guide

Transcription

1

2 Valve Selection Guide Series Inlet Sizes Available Metals Min. Temp F ( C) 0 / to - -( ) 0 ( ) Yes 00 (.) Air/Gas / Steam / Liquid ASME VIII, CE, CRN / to /Bronze - -( ) ( ) Yes 0 (.) Air/Gas / Steam / Liquid ASME VIII, CE, CRN / to /Carbon ( ) Yes 0 (.) Air/Gas / Steam / Liquid ASME VIII, CE, CRN / to - -( ) ( ) Yes 0 (.) Air/Gas / Steam / Liquid ASME VIII, CE, CRN / to Brass/SS/Bronze - -( ) ( ) Yes 0 (.0) Water / Liquid Non-Code / to Brass/SS/Bronze - -( ) 0 ( ) Yes (.) Air / Gas ASME VIII / to Brass/SS/Bronze - -( ) 0 ( ) Yes (.) Air / Gas ASME VIII -/ - /Bronze - -( ) 0 ( ) Yes 00 (.) Air / Gas Non-Code Brass/Bronze Max. Temp F ( C) - -( ) Soft Seat Max Pressure Available () Services Certifications -/ - /Bronze - -( ) 0 ( ) Yes (.) Air / Gas Non-Code 0 / to -/ Brass/Bronze - -( ) 0 ( ) Yes (.) Steam ASME I, CE, CRN / to -/ /Bronze - -( ) 0 ( ) Yes (.) Steam ASME I, CE, CRN 0 / to -/ - -( ) 0 ( ) Yes 00 (.) Air / Gas / Steam ASME VIII, CE, CRN / to -/ /Bronze - -( ) 0 ( ) Yes 00 (.) Air / Gas / Steam ASME VIII, CE, CRN / - - Brass/Bronze - -( ) 0 ( ) No 0 (.) Air / Gas / Steam ASME VIII, CRN 0 / -/ -/ Brass/Bronze - -( ) 0 ( ) No 0 (.) Air / Gas / Steam ASME VIII, CRN / -/ -/ Brass/Bronze - -( ) 0 ( ) No 0 (.) Liquid Non-Code 0 / -/ -/ Brass/SS - -( ) 0 ( ) No 0 (.0) Air / Gas / Steam Non-Code Brass/Bronze Multiply By Centimeters To Find Multiply By To Find kg / min. Pounds / Hr kg/cm^ kg / cm^. Kilopascals Kilopascals Inches Kilopascals 0.0 Centimeters 0.0 Feet Liters 000 Cm^ Cubic Feet / min 0.0 Meters^ / min Liters 0. Gallons Cubic Feet / sec. Gallons / Min. Liters / hr Gallons / Min Cubic Meters. Gallons Meters. Feet SCFM 0.0 Nm^ / min Meters 00 Centimeters SCFM. Nm^ / hr Pounds. Grams Feet 0.0 Meters Pounds 0. Kilograms Feet 0. Centimeters Pounds / hr. / M.W. SCFM Feet of Water 0. Inches of Mercury Pounds / hr 0. Kg / hr Feet of Water 0. Pounds / hr (Liquid).00 / S.G. Gallons / Min Gallons Cubic Centimeters. Inches of water Gallons 0. Cubic Feet 0.00 Kg / cm^ Gallons. Liters 0.0 Meters of water Gallons (Water). Pounds 0.0 Gallons / Min Cubic Feet / sec. Kilopascals Gallons / Min. x S.G. kg / hr Cm^ 0. Inch^ Gallons / Min.. Liters / min Inch^. Cm^ Gallons / Min. 0. Cubic Meters / hr Inch^. Mm^ Inches. Centimeters Inches 0.0 Feet Fahrenheit ( F-) * / Celsius Inches of Water 0.00 Celsius ( C *.) + Fahrenheit Kilograms. Pounds Fahrenheit F 0 = Rankine Kilograms. Ounces Celsius C = Kelvin

3 Aquatrol, Inc. Aquatrol is an American based manufacturer of safety and relief valve products; soon to be celebrating our 0th year anniversary. With this, we are proud to say that all products are manufactured right here, in the USA; allowing us to control all aspects of service and just as importantly, quality. Engineering, sales, manufacturing and assembly is done on-site and by an experienced team of safety and relief valve specialists allowing our customers to get what they need and when they need it. Our facilities include modern CNC manufacturing, robotics, in-house flow and capacity testing, CAD design and a myriad of other manufacturing specialties. We are growing to fit your needs. New, in is our Series 0 Safety Relief Valve line of products. This is a high capacity, full nozzle valve, certified by the ASME (Section VIII) for Air-Gas-Steam and Liquid services. Pressures are available up to 0 ; with the ability to choose standard brass/bronze metals or carbon steel and stainless steel valve options. See page for more information. The addition of new product allows Aquatrol to crossover with all screwed or portable safety and relief valve manufactures; and, on a world-wide basis. The depth of our offering helps to choose the best fit solution for most applications within the safety and relief valve industrial and commercial marketplace. Not changing from our companies strengths, we strive to offer 00% of our product line in stock. Your valves can be built, set, tested and shipped on a just in time basis. While helping to reduce inventory and expenses, this allows our customers the opportunity to make quick, accurate and timely decisions. We look forward towards being of service. Respectfully, Your Aquatrol Staff Please visit for expanded information.

4 Series 0 Safety Valves Series 0 safety and relief valve is designed for accuracy and reliability. Engineered for heavy-duty industrial usage. Multiple purpose safety and relief valve for all services: Liquid, Steam and Air/Gas. ASME and National Board Certified for Section VIII as well as CE and CRN Certifications. Pressures are to 0. Available with the full array of metal and seating options. Series 0 Brass, bronze construction with stainless steel ring, seat (Disc) and springs. ASME Section VIII to 00 for air/gas and liquid and for steam services. Series steel nozzle, ring, disc and springs. Bronze bonnet, and body. ASME Section VIII to 0 for Liquid and air/gas. 00 for Steam. Series steel nozzle, ring, disc and springs. Carbon steel body and bonnet. Ratings same as. Used as an all steel option. Series Same as, with stainless steel bonnet, body and components. Used where a stainless steel valve is required. Usages: Pressure Vessels, Pumps, Hydraulics, Tanks, Steam Systems, Chemical, Cryogenic, Air and Gas Compressors, Separators, by-pass and over pressure protection. Choose for most industrial applications requiring a safety relief valve. Features: Full nozzle Top guided design Short, precise blow-down Wide choice of inlet/outlet sizes Excellent re-seating characteristics Designed for heavy industrial use Closed hex cap Back-pressure tight Drain hole with threaded plug Cryogenic compatible Options: O-ring seating options (see charts) Packed lift lever Open lift lever BSPT Piping Tri-Clamp Inlets Full array of metal options API Seating CRN //

5 Series 0 thru # 0 DESCRIPTION Nozzle Lock Screw Lower Ring Disc Holder Lock Screw Disc Holder Shaft Disc Guide Bonnet Washer Seal Wire Hood Pressure Screw Lock Nut Spring Plate Spring Spring Post Spring Pin Guide Washer Disc Body Nozzle Washer Nameplate Washer 0 SA-CFM - SS Steel / Lead 0/- - SS B-C00 SA-CFM - SS Steel / Lead 0/- - SS B-C00 SA-CFM - SS SA0-/SA Steel / Lead SA0-0 0/- - SS SA-WCB SA-CFM - SS / Lead 0/- - SS A- SS Series 0 thru Orifice D D D D D E E E E E E E F F F G G G H H H J J J Flow Area In (mm). (0.). (0.). (0.). (0.). (0.). (0.0). (0.0). (0.0). (0.0). (0.0). (0.0). (0.0). (.). (.). (.). (.). (.). (.). (.). (.). (.). (.). (.). (.) Inlet / / / / -/ -/ -/ -/ -/ -/ -/ -/ Outlet -/ -/ -/ -/ -/ -/ -/ -/ -/ -/ DN Size I.D. C D E F G A B C D G F H F H G G H F H J K J K L A Closed Cap /" () /" () /" () /" () /" () /" () /" () /" () /" () /" () /" () /" () /" () /" () /" () 0 /" (0) 0 /" (0) 0 /" (0) /" () /" () /" () /" () /" () /" () Dimensions In. (mm) A B Lift Lever /" () /" (0) /" () /" (0) /" () /" (0) /" () /" (0) /" () /" (0) " () /" () " () /" () " () /" () " () /" () " () /" () " () /" () /" () /" () /" () /" () /" () /" () /" () /" () 0 /" (0) /" () 0 /" (0) /" () 0 /" (0) /" () /" (0) /" () /" (0) /" () /" (0) /" () /" () " (0) /" () " (0) /" () " (0) C /" /" /" /" /" " " " " " " " /" /" /" /" /" /" /" /" /" /" /" /" () () () () () () () () () () () () () () () () () () () () () () () () Weight Lb (Kg) (0.) (0.) (0.) (0.) (0.) (.) (.) (.) (.) (.) (.) (.) (.) (.) (.) (.) (.) (.) (.) (.) (.) (.) (.) (.)

6 Seating Materials Material Names Min Temp F ( C) Max Temp F ( C) FKM Viton-A - -( ) ( ) Nitrile Buna-N -0 -(0 ) EPDM FFKM -0 -(0 ) Kalrez -0 -( ) *Use for: Acetone, Air, Alcohol, Benzine, Butane, Ethylene, Ethylene Glycol, Ethyl Alcohol, Gasoline, Isobutyl Alcohol, Kerosene, Lube Oil, Natural Gas, Naphtha, Nitrogen, Propane, Water, Xylene Air, Butane, Carbon Dioxide, Diesel Oil, Ethyl Chloride, Ethyl Ether, Fuel Oil, Gasoline, Helium, ( ) Hydrogen Sulphide, Kerosene, Natural Gas, Nitrogen, Oxygen (Gas), Propane Steam, Water, Hot Water, Acetone, Beer, Brake Fluid, Hydrogen Gas, Sulfur Dioxide, Acids, 0 ( ) Alkalies Aromatic Hydrocarbons, Chlorinated Hydrocarbons, Polar Solvents (ketones, esters, ethers), 0 ( ) Inorganic and Organic Acids, Water, and Steam (Steam service up to 0 F ( C) saturated) -00 -( ) 0 ( ) Cryogenic Service including Argon, Carbon Dioxide, Helium, Hydrogen, Nitrogen, Oxygen, Steam Note: This is just a partial listing. Visit for links to websites with more specific applications. Seating # DESCRIPTION Nozzle Lower Ring Disc Holder Disc Holder Shaft Disc 0 SA-CFM SA-CFM SA-CFM SA-CFM O-Ring Seating # 0 SA-CFM - SS Various Metals Min. Temp F ( C) Max. Temp, F ( C) / to Brass/Bronze - -( ) 0 ( ) 00 / to /Bronze - -( ) ( ) 0 / to /Carbon - -( ) ( ) / to - -( ) ( ) Series Inlet Sizes 0 ) ) ) ) DESCRIPTION Nozzle Lower Ring Disc Holder Disc Holder Shaft O-Ring Disc Screw Disc Insert O-Ring Max Pressure, () SA-CFM - SS Various SA-CFM - SS Various SA-CFM - SS Various Services Certifications (.) Air / Gas / Steam / Liquid ASME VIII, CE, CRN (.) Air / Gas / Steam / Liquid ASME VIII, CE, CRN 0 (.) Air / Gas / Steam / Liquid ASME VIII, CE, CRN 0 (.) Air / Gas / Steam / Liquid ASME VIII, CE, CRN Maximum set pressure for steam service is 00 (. ) Maximum set pressure for steam on Series 0 is (. ) Maximum temperatures depend upon seating material. Contact Aquatrol for temps over F ( C)

7 Inlet / Lift Lever Options Open Lift Lever Options Material Options Item Description Handle C0/Plated C0/Plated C0/Plated Hood Anodized Alum. Anodized Alum. Anodized Alum. Lifter Nut Brass Jam Nut Lift Lever Pin Brass Spring Brass Carbon Steel Steel Optional Anti-Vibration Spring Packed Lift Lever Options Item Description 0 Handle Handle Screw Cam Retaining Ring O-RIngs Cam Nut O-RIng Hood Jam Nut Lifter Nut Hood Seal Plug Washer Gag Screw Brass Brass Steel/Plated Brass Steel/Plated Viton Brass Brass - Brass - - Material Options Carbon Steel Brass/Plated Steel/Plated - SS Viton SA0-C Steel Brass/Plated Steel/Plated - SS Viton Inlet Options: BSPP NPT or BSPT NPT or BSPT Tri-Clamp Lifting Device as required by the ASME, ASME Section VIII: UG() Each pressure relief valve on air, water at the valve inlet that exceeds 0 F (0 C), excluding over-pressure or relief events, or steam service shall have a substantial lifting device which when activated will release the seating force on the disc when the pressure relief valve is subjected to a pressure of at least % of the set pressure of the valve.

8 Series 0 thru - Threaded Inlet Part Numbers 0 Series 0 ED Description Brass/Bronze SS/Bronze SS/Carbon Orifice/Size ID DC- / x DD- / x DE- x DF- x DG- x EA- / x EB- / x -/ EC- x ED- x -/ EG- x EF- x -/ EH- -/ x -/ FF- x -/ FH- -/ x -/ FG- -/ x -/ GG- -/ x GH- -/ x GF- x HH- -/ x -/ HJ- x -/ HK- -/ x -/ JJ- x JK- -/ x V Connection - NPT MxF - NPT FxF - BSPT MxF - BSPT FxF - BSPP MxF - BSPP FxF Seating M- Metal P- R- PCTFE V- Viton B- Buna K- Kalrez E- EPDM - Cap Lift lever Closed cap Packed lift lever Lift Lever with Anti-Vibe Spring - Closed Cap with Test Gag - Packed Lever with Test Gag J KLJPEDNTU- Service ASME VIII-Air/gas ASME VIII-Steam ASME VIII-Liquid CE - Air/gas CE - Steam CE - Liquid Non-code Air/gas Non-code Steam Non-code Liquid - Options None Chrome Plating O Cleaned API Seating O Clean / API Seating Ex. Note: This chart is for threaded inlets only. JL- x Series 0 thru - Tri-Clamp Inlet Part Numbers Series 0 Description Brass/Bronze SS/Bronze SS/Carbon ED Orifice/Size ID DE- x DF- x DH- x DG- x DJ- -/ x DK- -/ x EC- x ED- x -/ EG- x EF- x -/ EJ- -/ x EK- -/ x -/ FF- x -/ FG- -/ x -/ GE- x GH- -/ x HH- -/ x -/ HJ- x -/ JG- -/ x JJ- x M Connection Seating MMetal Tri-clamp x NPT P- Tri-clamp x R- PCTFE BSPT V- Viton B- Buna K- Kalrez E- EPDM - Cap Lift lever Closed cap Packed lift lever Lift Lever with Anti-Vibe Spring - Closed Cap with Test Gag - Packed Lever with Test Gag Note: This chart is for Tri-Clamp inlets only L KLJPEDNTU- Service ASME VIII - Air/gas ASME VIII - Steam ASME VIII - Liquid CE - Air/gas CE - Steam CE - Liquid Non-code Air/gas Non-code Steam Non-code Liquid - Options None Chrome Plating O Cleaned API Seating O Clean / API Seating Ex.

9 Liquid Capacity Series 0 thru Capacities Liquid GPM ASME Section VIII Orifice area in^ Series 0 thru Capacities Liquid LPM ASME Section VIII Flow Coefficient =. Orifice area mm^ D. E. F. G. H. J Flow Coefficient =. D. E 0.0 F. G. H. J pressures below (.0 ) are NON-Code. Maximum back-pressure is 0% of set pressure or 0 (. ) whichever is less. Lifting Device as required by the ASME, ASME Section VIII: UG() Each pressure relief valve on air, water at the valve inlet that exceeds 0 F (0 C), excluding overpressure or relief events, or steam service shall have a substantial lifting device which when activated will release the seating force on the disc when the pressure relief valve is subjected to a pressure of at least % of the set pressure of the valve.

10 Air Capacity Series 0 thru Capacities Air SCFM ASME Section VIII Orifice area in^ Series 0 thru Capacities Air Nm/hr ASME Section VIII Flow Coefficient =. Orifice area in^ D. E. F. G. H. J Flow Coefficient =. D. E 0.0 F. G. H. J pressures below (.0 ) are NON-Code. Maximum back-pressure is 0% of set pressure or 0 (. ) whichever is less. Lifting Device as required by the ASME, ASME Section VIII: UG() Each pressure relief valve on air, water at the valve inlet that exceeds 0 F (0 C), excluding overpressure or relief events, or steam service shall have a substantial lifting device which when activated will release the seating force on the disc when the pressure relief valve is subjected to a pressure of at least % of the set pressure of the valve. 0

11 Steam Capacity Series 0 thru Capacities Steam Lbs/hr ASME Section VIII Orifice area in^ Series 0 thru Capacities Steam Kg/hr ASME Section VIII Flow Coefficient =. Orifice area in^ D. E. F. G. H. J Flow Coefficient =. D. E 0.0 F. G. H. J pressures below (.0 ) are NON-Code. Maximum back-pressure is 0% of set pressure or 0 (. ) whichever is less. Lifting Device as required by the ASME, ASME Section VIII: UG() Each pressure relief valve on air, water at the valve inlet that exceeds 0 F (0 C), excluding overpressure or relief events, or steam service shall have a substantial lifting device which when activated will release the seating force on the disc when the pressure relief valve is subjected to a pressure of at least % of the set pressure of the valve.

12 Series 0/0 Safety Valves Our 0 / 0 valve line is a high capacity safety valve used for boilers, piping lines and vessel protection. Designed and engineered for heavy-duty industrial use. ASME and National Board Certified for Section I and VIII as well as CE and CRN Certifications. Series 0 Use for ASME Section I applications, set pressure up to (. ). Boilers, or most areas where steam safety valves are required. Series Same as Series 0 except with Steel wetted trimming (Nozzle and Disc). Series 0 ASME Section VIII, CE, CRN certified for unfired vessel protection. pressure up to 00 (. ). Used for many applications to protect or relieve pressure for Air / Gas or Steam. Series Same as Series 0 except with Steel wetted trimming (Nozzle and Disc). Usages: Steam Boilers, Air Compressors, Dryers, Receivers, Pressure Vessels, Piping Systems, Accumulators, Reducing Stations, Tanks, Inter/After Coolers, Cooking Equipment, Autoclaves, Sterilizers or wherever higher capacity pressure protection or relief may be required. Features: Designed for durability orifices sizes of piping options Top guided seating and discharge Full nozzle, high capacity levels Short, tuned blow-down with dual-ring technology Heavy duty hood and lever mechanism Standard - stainless steel springs Options: O-ring seating options (see charts) Packed lift lever steel trimming package, nozzle, disc (all sizes) O-ring seating options (, EPDM, Viton, or as specified) Bubble tight seating options Anti-vibration spring for lift lever BSPT pipe threading CRN //

13 Series 0 / 0 / / ITEM 0 DESCRIPTION Body Bonnet Lower Ring Lock Screw Upper Ring Spring Support Lift Lever Seal Wire Hood Lifter Nut Jam Nut Lever Pin Pressure Screw Lock Nut Stem Spring Plate Spring Disc Nut Ball Bearing Disc Name Plate 0 / 0 /B-C00 B-C00 B-C00 B-C00 Steel / Plated Steel / Galvanized Aluminum / Plated / A- SS B-C00 B-C00 B-C00 Steel / Plated Steel / Galvanized Aluminum / Plated A- SS Series Weight Lbs. (Kg) C Dimensions In. (mm) A B C -/" () /" () /" () D /" () /" () /" (). (.) D /" () /" () /" () (.) E /" () /" () /" () (.) -/ E /" () /" () /" () (.) -/ F /" () /" () /" () (.) -/ -/ F /" () /" () /" () (.). (.) -/ -/ 0 G /" () /" () /" () (.). (0.0) -/ 0 G " () /" () /" () 0 (.) H. (0.0) 0 H " () /" () /" () 0 (.) J. (.) -/ 0 H /" () " (0) /" () (.) J. (.) -/ -/ J /" () " (0) /" () (.) Orifice Flow Area In (mm) Inlet Outlet DN Size I.D. D. (0.) / D. (0.) E. (.) E. (.) F. (.) F. (.) -/ G. (.) G H Series Inlet Sizes Metals 0 / to -/ Brass/Bronze. (.) Min. Temp F ( C) Max. Temp F ( C) Max Pressure () Services Certifications - -( ) 0 ( ) (.) Steam ASME I, CE, CRN / to -/ /Bronze - -( ) ( ) (.) Steam ASME I, CE, CRN 0 / to -/ - -( ) 0 ( ) 00 (.) Air / Gas / Steam ASME VIII, CE, CRN / to -/ /Bronze - -( ) ( ) 00 (.) Air / Gas / Steam ASME VIII, CE, CRN Brass/Bronze

14 Seating Materials Material Names Min Temp F ( C) Max Temp F ( C) FKM Viton-A - -( ) ( ) Nitrile Buna-N -0 -(0 ) EPDM FFKM -0 -(0 ) Kalrez -0 -( ) *Use for: Acetone, Air, Alcohol, Benzine, Butane, Ethylene, Ethylene Glycol, Ethyl Alcohol, Gasoline, Isobutyl Alcohol, Kerosene, Lube Oil, Natural Gas, Naphtha, Nitrogen, Propane, Water, Xylene Air, Butane, Carbon Dioxide, Diesel Oil, Ethyl Chloride, Ethyl Ether, Fuel Oil, Gasoline, Helium, ( ) Hydrogen Sulphide, Kerosene, Natural Gas, Nitrogen, Oxygen (Gas), Propane Steam, Water, Hot Water, Acetone, Beer, Brake Fluid, Hydrogen Gas, Sulfur Dioxide, Acids, 0 ( ) Alkalies Aromatic Hydrocarbons, Chlorinated Hydrocarbons, Polar Solvents (ketones, esters, ethers), 0 ( ) Inorganic and Organic Acids, Water, and Steam (Steam service up to 0 F ( C) saturated) -00 -( ) 0 ( ) Cryogenic Service including Argon, Carbon Dioxide, Helium, Hydrogen, Nitrogen, Oxygen, Steam Note: This is just a partial listing. Visit for links to websites with more specific applications. Soft seat option ITEM DESCRIPTION Disc O-Ring Center Insert Screw 0 / 0 Various - / A- SS Various A- SS - Soft Seat Option Series Part Numbers Series/Description 00- DC Orifice/Size ID M Connection Seating Brass/bronze Section I DC- / x - NPT MxF M- Metal - Lift lever DD- x - NPT FxF P- - Packed lift lever SS/Bronze Section I ED- x - BSPT MxF E- EPDM EE- x - BSPT FxF Brass/bronze Section VIII FE- x -/ - BSPP MxF B- Buna FF- -/ x -/ - BSPP FxF SS/bronze GF- -/ x -/ Section VIII GG- -/ x -/ V- Viton K- Kalrez Cap - Lift Lever with Anti Vibe Spring L Service Options K- ASME VIII - Air/gas - None L- ASME VIII - Steam A- ASME I Steam P- CE - Air/gas Packed Lever with E- CE - Steam Test Gag N- Non-code Air/gas - Easy Test Lever HG- -/ x HH- x JH- x -/ JJ- -/ x -/ T- Non-code Steam - Chrome Plating - O Cleaned - API Seating - O Clean / API Seating Ex.

15 Section I Steam Capacity Series 0 Capacities Steam Lbs/hr ASME Section I Orifice area in^ D E F Series 0 Capacities Steam Kg/hr ASME Section I Flow Coefficient =. G H Orifice area in^ J D E F Flow Coefficient =. G H J pressures on steam below (.0 ) and above (. ) are NON-Code. Section I Lift levers can not be omitted. Lifting Device as required by the ASME: ASME Section I - PG-.. Each safety valve shall have a substantial lifting device, which when activated will release the seating force on the disc when the valve is subjected to a pressure of at least % of the set pressure.

16 Section VIII Steam Capacity Series 0 Capacities Steam Lbs/hr ASME Section VIII Orifice area in^ D E F Series 0 Capacities Steam Kg/hr ASME Section VIII Flow Coefficient =. G H Orifice area in^ J pressures on steam below (.0 ) and above (. ) are NON-Code. Lifting Device as required by the ASME, ASME Section VIII: UG() Each pressure relief valve on air, water at the valve inlet that exceeds 0 F (0 C), excluding overpressure or relief events, or steam service shall have a substantial lifting device which when activated will release the seating force on the disc when the pressure relief valve is subjected to a pressure of at least % of the set pressure of the valve. D 0. 0 E F Flow Coefficient =. G H J

17 Section VIII Air Capacity Series 0 Capacities Air SCFM ASME Section VIII Orifice area in^ D E F Series 0 Capacities Air Nm/hr ASME Section VIII Flow Coefficient =. G H Orifice area in^ J D E F. 0 0 Flow Coefficient =. G H J pressures on air below (.0 ) and above 00 (. ) are NON-Code. Lifting Device as required by the ASME, ASME Section VIII: UG() Each pressure relief valve on air, water at the valve inlet that exceeds 0 F (0 C), excluding overpressure or relief events, or steam service shall have a substantial lifting device which when activated will release the seating force on the disc when the pressure relief valve is subjected to a pressure of at least % of the set pressure of the valve.

18 Series Relief Valves Series is a non-code, industry standard relief valve used for liquid relief and by-pass. Engineered and designed for heavy duty, industrial and commercial usages. A single piece bonnet to eliminate leakage while allowing for simple cleaning. Easy removable sealed hex-cap to adjust pressure. Series Series relief valves are calibrated (set to pressure) based on a range of flow-rates (GPM) versus seat size and set pressure. Standard valve is set to pressure to achieve flow rate maximum and minimums within each set pressure range. See capacity chart for details. Usages: Include liquid by-pass, regulation, continuous relief and overprotection. Used on pumping stations, tanks, hydraulics, fluid / piping lines, oil fields, gas lines and more where a Liquid or Water Relief Valve is needed. Features: Field adjustable by simple removal of the hex-cap Metal to metal precision lapped seating Back pressure tested at factory Ease of cleaning and maintenance with simple bonnet removal. steel springs Single piece leak free bonnet Options: BSPT connections Female inlet Viton embedded o-ring at hex cap Packed lift lever Wide range WR adjustable (0 increments) steel body and disk Low Lead Configurations (for a potable Water Relief Valve) Seating Adjustable wheel handle Tamper proof wire seal O Cleaning Wide Range: Series is available with a wider adjustable range (as an option). Valves are set to the mid-level pressure (or as specified). Typical wide-range is 0 increments. Note: Flow rates are not showing. //

19 Series 0 "A" "B" Item Description Brass Option Option 0 Body Bonnet Ball Disc Nameplate Disc Nut Spring Support Spring Spring Plate Washer Hood Pressure Screw Spring Post Lock-nut /B B B 0/- Nylon B 0/- Nylon "C" Female Connections "A" Dimensions same as Male Series Size I.D. Inlet Outlet DN A A B B C C D D E E F F G G H / / -/ -/ -/ -/ -/ -/ / -/ -/ -/ -/ -/ -/ Dimensions In. (mm) B C " () /" () /" " () /" () /" /" () /" () /" /" () /" () /" /" () /" () /" /" () /" () /" /" () /" () " /" () /" () " /" () /" () /" /" () /" () /" " () /" () /" " () /" () /" " (0) /" () /" " (0) /" () /" /" () /" () /" Weight Lb - (Kg) A () () () () () () () () () () () () () () (). (0.). (0.). (). () (.) (.) (.) (.). (.). (.). (.). (.) (.) (.) (.)

20 Soft Seat Item Description Material Body /C Support Disc Insert Disc Wings Packed Lift Lever Options Item Description 0 Handle Handle Screw Cam Retaining Ring O-RIngs Cam Nut O-RIng Hood Jam Nut Lifter Nut Hood Seal Plug Washer Gag Screw Brass Brass Steel/Plated Brass Steel/Plated Viton Brass Brass - Brass - - Open Lift Lever Options Material Options Item Description Brass Carbon Steel Steel Handle C0/Plated C0/Plated C0/Plated Hood Anodized Alum. Anodized Alum. Anodized Alum. Lifter Nut Brass Jam Nut Lift Lever Pin Brass Spring Optional Anti-Vibration Spring Inlet Options: BSPP NPT or BSPT NPT or BSPT Material Options Carbon Steel Brass/Plated Steel/Plated - SS Viton SA0-C Steel Brass/Plated Steel/Plated - SS Viton - - -

21 Series Part Numbers C A Series Inlet Outlet A- / Same Size as Inlet B- C- Next Larger than Inlet D- -/ E- -/ F- G- -/ H- Metals A- Brass/Bronze SS NozzleBDisc w/bronze L- No Lead NozzleDisc w/bronze M- SS/ No Lead Bronze M Connection Seating - NPT MxF M- Metal - NPT FxF P- - BSPT MxF - BSPT FxF - BSPP MxF - BSPP FxF U Cap Service Options - Lift lever Non-Code - None ULiquid - Closed cap Chrome Plating - Packed lift lever Lift Lever AntiO Vibration Spring Cleaned - Closed Cap with Test Gag - Packed Lever with Test Gag Ex. Closed Cap With O-Ring W- Wheel Handle - Series Liquid Capacity GPM at % Over Pressure Series Liquid Capacity LPM at % Over Pressure Flow Factor Flow Factor A / B 0 C D E -/ -/ F G -/ H A / B C D E F G H -/ -/ -/

22 Series Safety Valves Series / Series and are multiple purpose safety valves for air / gas protection. Designed for durability, yet an economical choice for safety and relief applications. Choose for a variety of applications where mid-level capacity is required. ASME and National Board Certified for Section VIII as well as CRN Certifications. Usages: Over pressure protection on Pressure vessels, Piping systems, Tanks, Compressors, Dryers, Inter and After-coolers Features: Adjustable tuned blow-down Precision lapped metal to metal seating steel springs Ruggedly constructed Closed seal hex cap or lift lever options Wide variety of inlet and outlet options Disk-guided seat provides quick, accurate and excellent re-seating Options: steel body and disk Chrome plating Viton embedded o-ring at hex cap Packed lift lever Low Lead Configurations Seating Oxygen cleaning BSPT connections Cryogenic: Standard with seating O Cleaned and bagged CRN //

23 Series / Item Description Brass 0 Body Disc Bonnet Lock Screw Lower Ring Ball Disc Nut Spring Support Lift Lever Seal Wire Hood Lifter Nut Jam Nut Lever Pin Pressure Screw Locknut Spring Post Spring Plate Spring Nameplate Hood Washer /B B B B Plated Steel Steel / Lead Aluminum - 0/- Nylon B B Plated Steel Steel / Lead Aluminum - 0/- Nylon 0 "A" SEAL "B" "C" /" & /" Series Series /" - /" Lift Levers Series / Size I.D. Inlet Outlet DN A A B B C C D D E E F F G G H / / -/ -/ -/ -/ -/ -/ / -/ -/ -/ -/ -/ -/ A- /" () /" () /" () /" () /" (0) /" (0) /" () /" () /" () /" () /" () /" () /" () /" () /" () Dimensions In. (mm) A- B " () /" () " () /" () /" () /" () /" () /" () /" () /" () /" () /" () /" () /" () /" () /" () /" () /" () /" () /" () " () /" () " () /" () " (0) /" () " (0) /" () /" () /" () C /" /" /" /" /" /" " " /" /" /" /" /" /" /" () () () () () () () () () () () () () () () Weight Lb - (Kg). (0.). (0.). (). () (.) (.) (.) (.). (.). (.). (.). (.) (.) (.) (.)

24 Soft Seat Item Description Brass Body Lower Ring Disc Wings Insert Disc Support /B B B Packed Lift Lever Options Item Description 0 Handle Handle Screw Cam Retaining Ring O-RIngs Cam Nut O-RIng Hood Jam Nut Lifter Nut Hood Seal Plug Washer Gag Screw Brass Brass Steel/Plated Brass Steel/Plated Viton Brass Brass - Brass - - Material Options Carbon Steel Brass/Plated Steel/Plated - SS Viton SA0-C Steel Brass/Plated Steel/Plated - SS Viton Series / Part Numbers C A M K Series Inlet Outlet Metals Connection Seating Cap Service Options M- Metal P- - Lift lever - Closed cap - Packed Lift Lever ABCDEFGH- / -/ -/ -/ - Same Size as Inlet Next Larger than Inlet A- Brass/Bronze B- SS Nozzle Disc w/bronze L- No Lead Nozzle Disc w/bronze M- SS/ No Lead Bronze - NPT MxF NPT FxF BSPT MxF BSPT FxF BSPP MxF BSPP FxF - Lift Lever AntiVibration Spring - Closed Cap with Test Gag - Packed Lever with Test Gag - Closed Cap with O-Ring Ex. ASME VIII - None Air/gas Chrome Plating Non-code NAir/gas - O Cleaned Non-code - API Seating TSteam O Clean / API Seating K-

25 Air Capacities Series / Air Capacity 0% over Pressure Series / Air Capacity 0% over Pressure Slope Slope A / B C D -/ E -/ F G -/ H A / B C D -/ E -/ F G -/ H pressures below (.0 ) and above (. bar) are NON-Code. Maximum back-pressure is 0% of set pressure or 0 (. ) whichever is less. Lifting Device as required by the ASME, ASME Section VIII: UG() Each pressure relief valve on air, water at the valve inlet that exceeds 0 F (0 C), excluding overpressure or relief events, or steam service shall have a substantial lifting device which when activated will release the seating force on the disc when the pressure relief valve is subjected to a pressure of at least % of the set pressure of the valve.

26 Series Safety Valves Series - Our Series air/gas and steam safety valve is designed for safety and pressure relief for light and medium capacity applications where a smaller sized valve is needed. The series valves have a higher capacity than our Series 0. Many are manufactured to meet specific field and OEM applications. ASME and National Board Certified for Section VIII as well as CRN Certifications. Usages: High quality smaller valve, Compressors, Receivers, Gas lines,steam lines, Air and Gas receivers, Piping system/tanks,steam cleaners, sterilizers, Autoclaves Features: Fixed blow-down Brass/bronze construction Metal-to-metal seating Rugged, yet economical steel springs Factory set and sealed Excellent seat tightness Options: body and disk Polishing and chrome plating Oxygen cleaning Variety of inlets/outlets and lift levers or pull ring Many configurations (not shown) Oxygen cleaning BSPT connections pressures below (.0 ) and above 0 (. bar) are NON-Code. Maximum back-pressure is 0% of set pressure or 0 (. ) whichever is less. Lifting Device as required by the ASME, ASME Section VIII: UG() Each pressure relief valve on air, water at the valve inlet that exceeds 0 F (0 C), excluding overpressure or relief events, or steam service shall have a substantial lifting device which when activated will release the seating force on the disc when the pressure relief valve is subjected to a pressure of at least % of the set pressure of the valve. CRN //

27 B B Series thru A A Series Series A A Item Description Brass Option Option Body Disc Bronze Seal Wire Steel/Lead Steel/Lead Lock Screw Bonnet Bronze Bronze Support Spring Plate Brass Brass Lift Lever Plated Steel Plated Steel Spring 0 Spring Post Lift Pin Nameplate Hood Bronze Bronze Lever Pin Hood Mount B B C C Series Series Series thru Series Inlet Outlet Seat * * * * / / / / Top Top Top Top Top Top Top Top Dimensions Inches (mm) A /" /" /" /" /" /" /" /" /" /" /" /" /" /" /" /" () () () () (0) (0) (0) () () () () () (0) (0) (0) () B /" /" /" /" /" /" /" /" Max. (g) C () () () () () () () () /" /" /" /" /" /" /" /" /" /" /" /" /" /" /" /" () () () () () () () () () () () () () () () () 0 (.) 0 (.) 0 (.) 0 (.) 0 (.) 0 (.) 0 (.) 0 (.) 0 (.) 0 (.) 0 (.) 0 (.) 0 (.) 0 (.) 0 (.) 0 (.) Weight Lbs (Kg) (.) (.) (.) (.) (.) (.0) (.0) (.) (.) (.) (.) (.) (.) (.) (.) (.) * seat is non-code

28 Series thru Part Numbers B A M K Series/Description Inlet/Outlet Metals Connection Seating Cap Service Options Top Outlet w/lift Lever Top Outlet Hood And Lift Lever Side Outlet w/lift Lever Side Outlet Hood And Lift Lever A- / B- C- *D- x A- / x B- x C- x *D- x A- Brass Bronze B- SS Bronze No Lead LBronze M- - NPT MxF NPT FxF BSPT MxF BSPT FxF BSPP MxF BSPP FxF M- Metal - Lift lever Hood and HLift Lever K- ASME VIII Air/gas L- ASME VIII Steam Non-code NAir/gas SS No Lead T- - None Ex. Chrome Plating - O Cleaned Non-code Steam pressures below (.0 ) or above 0 (. ) are non-code Inlet/Outlet D are non-code valves Series thru Series thru Air Capacity 0% Over Pressure Air Capacity 0% Over Pressure Slope.0 Seat. Seat* Slope.0 Seat. Seat* Series thru Series thru Steam Capacity 0% Over Pressure Steam Capacity 0% Over Pressure Slope.. Slope.. Seat Seat* Seat Seat* * Seat is Non-Code

29 Series 0 Safety Valves Series 0 - Our Series 0 air/gas and steam safety valves are designed for safety and pressure relief for light and medium capacity applications; where a smaller sized valve is needed. Many are manufactured to meet specific field and OEM applications. ASME and National Board Certified for Section VIII as well as CRN Certifications. Usages: Compressors, Receivers, Gas lines, Steam lines, Air and Gas receivers, Piping system/tanks, Steam cleaners, sterilizers, Autoclaves Features: Fixed blow-down Brass/bronze construction Metal-to-metal seating Rugged, yet economical steel springs Factory set and sealed Excellent seat tightness Options: body and disk Polishing and chrome plating Oxygen cleaning Variety of inlets/outlets and lift levers or pull ring Oxygen cleaning BSPT connections pressures below (.0 ) and above 0 (. bar) are NON-Code. Maximum back-pressure is 0% of set pressure or 0 (. ) whichever is less. Lifting Device as required by the ASME, ASME Section VIII: UG() Each pressure relief valve on air, water at the valve inlet that exceeds 0 F (0 C), excluding overpressure or relief events, or steam service shall have a substantial lifting device which when activated will release the seating force on the disc when the pressure relief valve is subjected to a pressure of at least % of the set pressure of the valve. CRN //

30 C C Series 0 thru A A Series 0 Series A A Item Description Brass Option Option Body Disc Bronze Seal Wire Steel/Lead Steel/Lead Lock Screw Bonnet Bronze Bronze Support Spring Plate Brass Brass Lift Lever Plated Steel Plated Steel Spring 0 Spring Post Lift Pin Nameplate Hood Bronze Bronze Lever Pin Hood Mount B B C C Series Series Series 0,,, Series Inlet Outlet Seat / / / / / / / / / / / / Top Top Top Top Top Top / / / / / / / / / / / / / / / / / / A /" /" /" /" /" /" /" /" /" " " " Dimensions Inches (mm) B C () /" () /" () /" () /" () /" () /" () /" () /" () /" () /" () /" () /" () /" () /" () /" () /" () /" () /" 0 Max. (g) () () () () () () () () () () () () 0 (.) 0 (.) 0 (.) 0 (.) 0 (.) 0 (.) 0 (.) 0 (.) 0 (.) 0 (.) 0 (.) 0 (.) Weight Lbs (Kg) / / / / / / / / / / / / (.) (.) (.) (.) (.) (.) (.) (.) (.) (.) (.) (.)

31 Series 0 thru Part Numbers 0 B A M K Series/Description Inlet/Outlet Metals Connection Seating Cap Service Options 0 Top Outlet w/lift Lever Top Outlet Hood And Lift Lever Side Outlet Hood And Lift Lever Side Outlet Closed Cap A- / B- / C- / A- Brass Bronze B- SS Bronze No Lead LBronze A- / x / B- / x / SS MNo Lead C- / x / - NPT MxF M- Metal NPT FxF BSPT MxF BSPT FxF BSPP MxF BSPP FxF - Lift lever Closed Cap Hood and HLift Lever K- ASME VIII Air/gas L- ASME VIII Steam Non-code NAir/gas T- Series 0 thru Series 0 thru Air Capacity 0% Over Pressure Air Capacity 0% Over Pressure Slope = None Ex. Chrome Plating - O Cleaned Non-code Steam Slope = 0.0 All Sizes All Sizes Series 0 thru Series 0 thru Steam Capacity 0% Over Pressure Steam Capacity 0% Over Pressure Slope =. Slope =. All Sizes All Sizes

32 Series 0 Safety Valves Series 0 A ball-seated safety valve used for applications where higher capacity may be required with a smaller sized valve. Designed, tested and built for heavy-duty applications. Note: Currently non-asme code Usages: Steel Ball Disc Fixed blow-down Factory preset to specified pressures Features: Pressures to 0 P.S.I. Economical Steel Spring Steel Ball Disc Fixed blow-down Factory preset to specified pressures Options: BSPT Inlet Female Inlet Oxygen Cleaning Full Steel Construction //

33 Series 0 Item Description Brass Option Option 0 Body Disk Disk Holder Name Plate Spring Plate Pressure Screw Pull Ring Spring Post Hood Lock Nut Spring Bonnet Brass Brass Aluminum Brass Brass Plated Steel Brass Brass Brass A-0 SS Brass 0 Aluminum Plated Steel 0 / - Series 0 Capacity Series 0 Capacity Air 0% over set pressure Air 0% over set pressure SCFM SCFM Nm/hr Nm/hr Series 0 Part Numbers 0 Series / Description B A Inlet 0 Brass A- / Metals A- Brass Connection - NPT Male S.S. Nozzle B- / B- SS - NPT Female S.S. C- / - BSPT Male - BSPT Female - BSPP Male M N Seating Cap - Lift Lever Service M- Metal - Pull Ring NT- Non-code Air/gas Non-code Steam Options - None - Chrome Plating - O Cleaned Ex. - BSPP Female

34 Lift Lever Options Open Lift Lever Options Material Options Item Description Handle C0/Plated C0/Plated C0/Plated Hood Anodized Alum. Anodized Alum. Anodized Alum. Lifter Nut Brass Jam Nut Lift Lever Pin Brass Spring Brass Carbon Steel Steel Optional Anti-Vibration Spring Packed Lift Lever Options Item Description 0 Handle Handle Screw Cam Retaining Ring O-RIngs Cam Nut O-RIng Hood Jam Nut Lifter Nut Hood Seal Plug Washer Gag Screw Brass Brass Steel/Plated Brass Steel/Plated Viton Brass Brass - Brass - - Material Options Carbon Steel Brass/Plated Steel/Plated - SS Viton SA0-C Steel Brass/Plated Steel/Plated - SS Viton Easy Test Lever Options Item Description Handle Material Options Brass Carbon Steel Steel C0/Plated C0/Plated C0/Plated Hood Lift Washer Brass Brass Brass Cotter Pin Spring Post Lift lever options for Series,, 0 thru, 0 thru Easy Test Lever for Series 0 thru only Packed lever not available on Series 0 thru Lifting Device as required by the ASME, ASME Section VIII: UG() Each pressure relief valve on air, water at the valve inlet that exceeds 0 F (0 C), excluding over-pressure or relief events, or steam service shall have a substantial lifting device which when activated will release the seating force on the disc when the pressure relief valve is subjected to a pressure of at least % of the set pressure of the valve.

35 When Ordering Visit Aquatrol Valve Series Number Inlet Size x Outlet Size Special Seating Service Steam, Air, Gas or Liquid Special Options If Required Pressure Point Options (See Each Particular Valve For Details) Packed Lift Levers Soft Seating, O-Ring Seating Female Inlets Over-sized Inlets Various Steel(s) and Brass Grades BSPT Connections Polishing/Chrome Plating Closed Caps (as applicable by ASME code) Others Tri-Clamp Aquatrol, Inc Fax: 0-- Industries Served (By Aquatrol Valves) CAD files of valves / Cut sheets Operating and installation manuals Basic sizing guidelines Cleaning instructions Flow/pressure charts /metric Glossary of safety and relief valve terms AND INDUSTRY GATEWAYS (LINKS) TO -Chemical compatibility charts -Equivalency links -VMA -The National Board -ASME Chemical/Pharmaceutical Marine/Mining Power/Energy Water Works Manufacturing Food/Beverage Construction Oil/Gas sales@aquatrol.com Our Guarantee/Warranty Unless otherwise agreed upon, Aquatrol valves are guaranteed for a period of year from shipment. The guarantee covers all parts and labor. The guarantee applies to valves properly used under industry standards for sizing and usages. Aquatrol will not be held responsible for any form of incidental or consequential damages. Our valves all ship FOB, Elburn, IL. Unless otherwise specified, we will choose the most efficient manner of delivery.

36 // 0:0 PM