THREE HOLE SPLICE CLEVIS FOR B52 Standard finishes: ZN, GRN Wt./C 126 Lbs. (57.1 kg)

Transcription

1 CLEVIS FITTINGS B169 TWO HOLE SPLICE Wt./C 84 Lbs. (38.1 kg) B168 THREE HOLE SPLICE Wt./C 126 Lbs. (57.1 kg) B167 Wt./C 178 Lbs. (80.7 kg) 3 1 /2 (88.9) B170 TWO HOLE SPLICE Wt./C 123 Lbs. (55.8 kg) 5 3 /8 (136.5) B171 THREE HOLE SPLICE Wt./C 195 Lbs. (88.4 kg) 7 B172 Wt./C 266 Lbs. (120.6 kg) 3 1 /2 (88.9) 5 3 /8 (136.5) 7 & B CLEVIS FOR B12 Wt./C 326 Lbs. (147.8 kg) 7 B172-22A CLEVIS FOR B11 OR B22A Wt./C 406 Lbs. (184.1 kg) 7 B450 U-WASHER Material: ASTM A607 Gr. 50 H HOLE SIZE 11 Gauge (3.1) 1 5 /8 (41.3) 15 /32 (11.9) Part No. Hole Size Wt./C & Size H Lbs. kg B450-1 /4 5/16 (7.9) 14 B450-3 /8 7/16 (11.1) 14 B450-1 /2 9/16 (14.3) 13 (5.8) B450-5 /8 11/16 (17.4) 13 (5.8) B450-3 /4 13/16 (20.6) 13 (5.8) 72 page 58 for general fitting and standard finish specifications.

2 FITTINGS This section offers a full selection of fittings and accessories to complete B-Line s metal framing system. are made from hot rolled, pickled and oiled plate or strip steel in accordance with ASTM A907, unless noted. Dimensions The following dimensions apply to all fittings except as noted: Hole Size 9 /16 (14.3 mm) diameter Hole Spacing 1 7 /8 (47.6 mm) on center Hole Spacing 13 /16 (20.6 mm) from end Thickness (6.3 mm) Finishes* Finish Code Finish Specification PLN Plain ASTM A907 Gr. 33 ZN Electro-Plated Zinc ASTM B633 SC3 Type III GRN Dura-Green TT-C-490B HDG Hot-Dipped Galvanized ASTM A123 SS4 Stainless Steel Type 304 ASTM A240 SS6 Stainless Steel Type 316 ASTM A240 AL Aluminum ASTM B209 *Unless otherwise noted. Load Data The load data published includes safety factor of 2.5 when used with 12 ga. (2.6) channel (safety factor = ratio of ultimate load to the design load). Use 1 /2 by 7 /8 hex head cap screws and 1 /2 (N225 or TN225) channel nuts for the rated results. Recommended Bolt Torque Bolt Size 1 / / / /2-13 Foot/Lbs Nm See chart on page 98 for setscrew torque. Width 1 5 /8 (41.3 mm) Hardware Nuts and bolts are not included with the fittings and must be ordered separately, unless noted. Metric Metric dimensions are shown in parentheses. Unless noted, all metric dimensions are in millimeters. & 58

3 MINI CHANNEL & FITTINGS B-Line s mini channels and fittings provide for an economical method of supporting light load requirements on a metal framing system. Channel Channels are cold formed on our modern rolling mills from 18 Ga. (1.2 mm) low carbon steel strips plain steel (ASTM A 611 Grade C) and pre-galvanized steel strips, (ASTM A653 SS Grade 33). A continuous slot with inturned lips provides the ability to make attachments at any point. Channel combinations are made with new state of the art, high-tech welding equipment. Lengths Standard lengths are 10 (3.05 m) and 20 (6.09 m) for B62 series, and 10 (3.05 m) for B72 series. Custom lengths are available. Mini fittings are formed from hot rolled pickled and oiled strip or sheet steel (ASTM A 607 Grade 50). The following dimensions apply to all fittings except as noted on the drawings: Hole Size 9 /32 (7.14 mm) Dia. Hole Spacing 13 /32 (10.3 mm) from end and 1 1 /16 (27.0 mm) on center. Width 13 /16 (20.6 mm) Thickness 1 /8 (3.2 mm) Finishes* Finish Code Finish Specification PLN Plain ASTM A607 Gr. 50 ZN Electro-Plated Zinc ASTM B633 SC3 Type II GRN Dura-Green TT-C-490B GALV Pre-Galvanized ASTM A653 SS Gr. 33 HDG Hot-Dipped Galvanized ASTM A123 *Unless otherwise noted. Metric Metric dimensions are shown in parentheses. Unless noted, all metric dimensions are in millimeters. Channel, & 174

4 & REFERENCE DATA METRIC CONVERSION CHART To Convert From To Multiply By To Convert From To Multiply By Angle Length degree radian (rad) x 10-2 foot (ft) meter (m) x 10-1 radian (rad) degree x inch (in) meter (m) x 10-2 mil meter (m) x 10-5 Area inch (in) micrometer (mm) x foot 2 square meter (m 2 ) x 10-2 meter (m) foot (ft) inch 2 square meter (m 2 ) x 10-4 meter (m) inch (in) x circular mil square meter (m 2 ) x meter (m) mil x sq. centimeter (cm 2 ) square inch (in 2 ) x 10-1 micrometer (mm) inch (in) x 10-5 square meter (m 2 ) foot x square meter (m 2 ) inch x Volume square meter (m 2 ) circular mil x foot 3 cubic meter (m 3 ) x 10-2 inch 3 cubic meter (m 3 ) x 10-5 Temperature cubic centimeter (cm 2 ) cubic inch (in 3 ) x 10-2 degree Fahrenheit degree Celsius t C =(t F -32)/1.8 cubic meter (m 3 ) foot x degree Celsius degree Fahrenheit t F =1.8t C +32 cubic meter (m 3 ) inch x gallon (U.S. liquid) cubic meter (m 3 ) x 10-3 Force pounds-force (lbf) newtons (N) x 10 Section Properties section modulus S (in 3 ) S (m 3 ) x 10-5 moment of inertia I (in 4 ) I (m 4 ) x 10-7 modulus of elasticity E (psi) E (Pa) x section modulus S (m 3 ) S (in 3 ) x moment of inertia I (m 4 ) I (in 4 ) x modulus of elasticity E (Pa) E (psi) x 10-4 To Convert From To Multiply By Bending Moment or Torque lbf ft newton meter (N m) lbf in newton meter (N m) x 10-1 N m lbf ft x 10-1 N m lbf in Mass ounce (avoirdupois) kilogram (kg) x 10-2 pound (avoirdupois) kilogram (kg) x 10-1 ton (short, 2000 lb) kilogram (kg) x ton (long, 2240 lb) kilogram (kg) x kilogram (kg) ounce (avoirdupois) x kilogram (kg) pound (avoirdupois) kilogram (kg) ton (short, 2000 lb) x 10-3 kilogram (kg) ton (long, 2240 lb) x 10-4 Mass Per Unit Length lb/ft kilogram per meter (kg/m) lb/in kilogram per meter (kg/m) x kg/m lb/ft x 10-1 kg/m lb/in x 10-1 Mass Per Unit Volume lb/ft 3 kilogram per cubic meter (kg/m 3 ) x lb/in 3 kilogram per cubic meter (kg/m 3 ) x kg/m 3 lb/ft x 10-2 kg/m 3 lb/in x 10-5 lbs/ft 3 lbs/in x 10-4 Mass Per Unit Area lb/ft 2 kilogram per square meter (kg/m 2 ) kg/m 2 pound per square foot (lb/ft 2 ) x 10-1 Pressure or Stress lbf/in 2 (psi) pascal (Pa) x kip/in 2 (ksi) pascal (Pa) x lbf/in 2 (psi) megapascals (MPa) x 10-3 pascal (Pa) pound-force per square inch (psi) x 10-4 pascal (Pa) kip per square inch (ksi) x 10-7 megapascals (MPa) lbf/in 2 (psi) x Defl. S.F. Ft. Pre-galv. K Factor o.c. PVC In. psi wt./c Abbreviations = Deflection = Safety Factor = Feet = Pre-galvanized Steel = Deflection Divided by load in Lbs./Ft. = On Center = Poly Vinyl Chloride = Inch = Pounds per Square Inch = Weight pre 100 pieces Metric Symbols m = meter cm = centimeter mm = millimeter µm = micrometer kg = kilogram N = newton kn = kilonewton Pa = pascal MPa = megapascal 202

5 INTRODUCTION B-Line Systems, Inc. is a leading manufacturer and fabricator of steel and aluminum products which are used in support of equipment for industrial, commercial, utility, and OEM installations. B-Line is proud of the exacting standards of research, design, engineering, and manufacturing that go into each and every product that comprise our metal framing product line. Our customers have access to the most complete support systems offered in the industry, including metal framing, cable tray, pipe hangers, slotted angle, and fasteners. Many of B-Line s products are listed by the Underwriter s Laboratories, Inc., and approved by the Factory Mutual Laboratories. All B-Line products are manufactured to meet or exceed MFMA and other industry standards set for their design and manufacture. B-Line products are produced in eight modern plants consisting of over 1,000,000 square feet. These facilities are located in Highland, Illinois; Troy, Illinois; Norcross, Georgia; Reno, Nevada; Sherman, Texas; Modesto, California; Portland, Oregon; and Aurora, Colorado. Regional sales and distribution centers are located throughout the United States stocking standard B-Line products for quick service and delivery. This catalog is designed to be helpful to engineers and contractors in the application and selection of strut products for construction and maintenance. If a unique application requires a special product not included in this catalog. B-Line engineering personnel are ready to furnish design consultation and realistic cost estimates. In addition, sales representatives with engineering know-how are located throughout the United States and abroad for your convenience. Cooper B-Line 509 West Monroe Street P.O. Box 326 Highland, Illinois Phone: B-Line Systems, Inc.