PRE-INSTALLATION BOLT CHART TOOLS / SUPPLIES REQUIRED:

Transcription

1 INSTALLATION MANUAL w w w. i n v i s i r ai l.cm

2

3 4 PRE-INSTALLATION REQUIREMENTS 4 BOLT SIZE CHART 5 POST INSTALLATION 5 ON-CENTRE POST MEASUREMENT CHART 6 POST BLOCKING DETAILS 7 FASCIA MOUNT POST CONNECTION DETAILS 8 GLASS SPECIFICATIONS 8 CONCRETE CONNECTION DETAILS 9 SPACER INFORMATION STAINLESS STEEL TOP RAIL INSTALLATION 12 tp rail BOARD bracket installatin 13 STAINLESS STEEL GLASS CONNECTOR INSTALLATION General Infrmatin InvisiPst - Cnnectr t Cnnectr InvisiPst - Cnnectr t Universal Angle Bracket 14 InvisiPst - Universal Angle Bracket t Universal Angle Bracket InvisiPst - End Pst with Cnnectr 15 InvisiPst - End Pst with Universal Angle Bracket VISTI POST and WOOD POST CONNECTOR INSTALLATION Straight Run Cnnectr Universal Angle Bracket 16 LITE 10 NYLON GLASS CONNECTOR INSTALLATION Lite 10 Angle Bracket 17 GLASS PANEL INSTALLATION Stainless Steel Cnnectrs Lite 10 Cnnectrs STAIR GLASS TEMPLATING INSTRUCTION INVISIPOST POSITIONING DETAIL DIAGRAMS VISTI POST POSITIONING DETAIL DIAGRAMS ALX pst POSITIONING DETAIL DIAGRAMS InvisiPst fascia munt POSITIONING DETAIL DIAGRAMS VISTIPst fascia munt POSITIONING DETAIL DIAGRAMS 37 Invisirail Scratch pad 38 Custm Hrizntal Glass Order Frm 3

4 PRE-INSTALLATION TOOLS / SUPPLIES REQUIRED: Tw (2) peple are necessary t handle and install glass Tape measure Drill with assrted bits including a T-40 bit fr deck fasteners and a 10mm hex scket if cnnecting t aluminum r wd psts Shims fr fine height adjustment t help in pin alignment during glass installatin Washers fr flange base adjustment t ensure psts are plumb during installatin Tw (2) shrt pieces f 2 x4 r 4 x4 t supprt glass during installatin Pipe cutter r saw with carbide-tipped metal cutting blade if installing stainless steel handrail r tp rail NOTE: There must be prper blcking in jists t secure psts! BOLT CHART Cnnectr t Universal Angle Bracket 4

5 POST INSTALLATION Only install ne panel sectin at a time. With InvisiPsts yu must slide the base cver nt pst befre attaching glass cnnectrs. DO NOT INSTALL POSTS BEFORE INSTALLING GLASS as minr adjustments may be needed t each pst. Start with the pst indicated n the layut diagram sent with yur rder. If necessary, use washer/s beneath the flange base t ensure yur pst is cmpletely plumb. Refer t the pst psitining diagrams in the back f this manual that apply t yur layut. Set the next pst accrding t the n-centre chart belw and the glass panel indicated n yur layut diagram. Remember t include any spacer measurements where indicated ON-CENTRE CHART Glass panels are 38 3/4 tall t be used fr a 42 rail height. Spans shwn in the stainless steel (SS) cnnectr chart assume that the 2mm backing plates are used with cnnectrs

6 BLOCKING DETAIL 4 LONG HEADLOK SCREWS (0.188 DIA) REFER TO SECTION FOR PLACEMENT 4 LONG HEADLOK SCREWS (0.188 DIA) 3 TOTAL DECKING MATERIAL BETWEEN BASE PLATE AND S INVISIPOST ALTERNATIVE BLOCKING DETAIL VISTI POST WITH BASE PLATE 5/16 X 6 GRK RSS SELF-DRILLING SCREWS ELEVATION HEADLOK SCREWS (4) 5/16 X 6 GRK RSS SELF-DRILLING SCREWS (4) 3/8 X 5 LAG SCREWS EACH END 6

7 FASCIA MOUNT CONNECTION HEADLOK SCREWS 7

8 Tempering Spec d as per CONCRETE CONNECTION ALTERNATIVE CONNECTION: 3/8 x 4 COBRA TORK CARBON STEEL ANCHOR- GLASS PANELS Rail Height: Rail Height: Rail Height: Rail Height: deck / surface 8

9 SPACERS Yur pst/panel layut diagram may indicate the requirement f spacers at certain lcatins. Spacers are used t make up small distances in the verall rail length in rder fr the railing t fit prperly n the deck. Shwn at right is an example f hw spacers are identified n a layut. Belw it is a picture f hw the spacer lks after installatin. InvisiRail spacers fr stainless steel cnnectrs cme in 3/8 (10mm), 1/2 (13m), 3/4 (19mm) and 1 (25mm) sizes. (2) x 1/2 indicates that ne spacer must be installed behind the tp cnnectr and ne behind the bttm cnnectr. Spacers fr Lite 10 nyln cnnectrs cme in, 3/8, 1/2 and 3/4 sizes. When referencing the n-centre chart t psitin yur psts be sure t ADD the spacer dimensin where indicated. 1 spacers 9

10 STAINLESS STEEL HANDRAIL TOP MOUNT INSTALLATION GENERAL INFORMATION Handrail brackets are installed between psts and glass cnnectrs / angle brackets, replacing the backing plates packaged with the cnnectrs. 42mm (1 5/8 ) diameter pipe with end cap Refer t pst detail drawings t determine the type f handrail bracket required with each pst. HANDRAIL PIPE INSTALLATION Install apprpriate left / right brackets n all intermediate and end psts and crner brackets n all crner psts. Remve the 1 blt frm the pivt and use the prvided 1 1/2 blt t cnnect the pivt t the bracket. InvisiPst Handrail Brackets Crner bracket Right hand bracket Crner pivt Carefully measure t determine the lengths f handrail required and cut yur pipe t length using a pipe cutter r saw with a carbide-tipped metal cutting blade. Left hand bracket Variable bracket fr nn 90-degree angles male / female jiners Jiners may be required fr lng spans requiring multiple lengths f pipe. T maintain a seamless length with multiple pipe pieces use the male jiners at the un-cut pipe ends. Rugh-cut pipe can be hidden with female jiners and/r in the female ends f the crner pivts. Pre-drill pilt hles and secure pipe t inline brackets with tapping screws. 5/32 cbalttipped drill bit and screws are prvided. Secure pipe t crner brackets using set screws lcated n the underside f the pivt. Fixtures (jiners, pivts r dmed ends) may be further secured t the pipe using prvided glue. 10 Use right hand bracket fr middle pst r left end pst Use shrt crner bracket fr utside 90-degree crners Use left hand bracket fr middle pst r right end pst Use lng crner bracket fr inside 90-degree crners

11 InvisiPst with shrt crner bracket and pivt n utside 90-degree crner InvisiPst with lng crner bracket and pivt n inside 90-degree crner Square pst with ALX crner bracket and pivt n utside 90-degree crner Square pst with ALX left and right brackets and pivt n inside 90-degree crner Square psts n nn 90- degree split angles can use left/right tp rail brackets (shwn at left) r a flangemunt handrail bracket (shwn abve) Transitining frm tp rail t stair rail is accmplished with tw pivts cnnected with a male jiner r shrt piece f rail pipe. Optinally, yu may terminate the tp rail with an end cap then install separate stair rail at the desired height. NO representatin is given that yur particular applicatin f these prducts cmplies with relevant building cdes. All prducts installed withut a tp rail DO NOT cmply with the USA IRC test reprt prvided by Intertek. Therefre, cnsult with prfessinals AND lcal building fficials befre starting t ensure cmpliance in yur area. The cnsumer r cntractr shuld take all necessary steps t ensure the safety f all invlved in installatin f the prject, including, but nt limited t use f safety glasses, wrk glves and safety shes. NO member f Liv Building Prducts, r Invisirail shall be liable fr any lss, damage r persnal injury due t the imprper installatin f prducts, r failure t use all items as per the USA-IRC test reprt. IN the unlikely event f any lss, damage r injury, the ttal aggregate liabilities will be limited t the retail purchase price f the prducts. 11

12 TOP RAIL BRACKETS FOR PRESSURE-TREATED, CEDAR OR COMPOSITE BOARD GENERAL INFORMATION Tp rail brackets are installed between psts and glass cnnectrs r angle brackets, replacing the backing plates packaged with yur stainless steel glass cnnectrs. BRACKET INSTALLATION Install ne bracket n every mid and end pst and tw brackets n all psts at crners r angles. Carefully measure t determine the lengths f tp rail required and cut yur bards t length. Crners and angles will require tp rail bards t be cut and secured at split angles. 12

13 STAINLESS STEEL GLASS CONNECTOR INSTALLATION GENERAL INFORMATION Only install the uter half f cnnectrs t psts. The remaining half gets installed with glass panel. Disassemble prir t installatin Glass panels cme with tw tp hles and tw bttm ntches. Fur cnnectr pins shuld be installed t secure glass t psts (minimum 1 per side must be used.) cnnectr pin Each cnnectr uses a 2mm (1/16 ) backing plate. InvisiPst: Cnnectr t Cnnectr Tp bracket t be installed in predrilled hle 40 inches O/C abve deck surface fr 42 inch rail height (34 inches fr 36 inch rail height.) Use the Blt Chart t determine the size yu need fr the applicatin. Refer t yur pst layut diagram t see if yu must add spacers. 5/16 X 1 1/2 blt Put the blt thrugh the cnnectr, backing plate (prvided in cnnectr packs), pst, backing plate and cnnectr. Thread the blt thrugh the nut n the ther side f the cnnectr. Make sure that cnnectrs are perfectly vertical! InvisiPst: Cnnectr t Universal Angle Bracket 5/16 X 1 blt Tp bracket t be installed in predrilled hle 40 inches O/C abve deck surface fr 42 inch rail height (34 inches fr 36 inch rail height.) Use the Blt Chart t determine the size yu need fr the applicatin. Refer t yur pst layut diagram t see if yu must add spacers. 13

14 Put the blt thrugh the cnnectr, backing plate (prvided in cnnectr packs), pst and thread int Universal Angle Bracket n the ther side. InvisiPst: Universal Angle Bracket t Universal Angle Bracket Disassemble the brackets by taking ut the lcking pin and hinge screw. Make sure yu have bth a threaded and a nn-threaded Universal Angle Bracket. 5/32 r 4mm hex key Tp bracket t be installed in predrilled hle 40 inches O/C abve deck surface fr 42 inch rail height (34 inches fr 36 inch rail height.) Use the Blt Chart t determine the size yu need fr the applicatin. Refer t yur pst layut diagram t see if yu must add spacers. 5/16 X 1 blt Put the blt thrugh the nn-threaded bracket, pst and thread int Universal Angle Bracket n the ther side. InvisiPst: End pst with Cnnectr Tp bracket t be installed in predrilled hle 40 inches O/C abve deck surface fr 42 inch rail height (34 inches fr 36 inch rail height.) Use the Blt Chart t determine the size yu need fr the applicatin. Refer t yur pst layut diagram t see if yu must add spacers. Put the blt thrugh the cnnectr, backing plate, pst and int the acrn nut prvided. 5/16 X 1 blt 14

15 InvisiPst: End pst with Universal Angle Bracket (UAB) Tp bracket t be installed in predrilled hle 40 inches O/C abve deck surface fr 42 inch rail height (34 inches fr 36 inch rail height.) Cnnectr t UAB: Thread a 5/16 X 1/2 blt thrugh the cnnectr int the swivel prtin f the bracket until tight. UAB t Pst: Thread a 5/16 X 1 blt thrugh bracket, pst and int the acrn nut prvided. VISTI OR ALX (ALUMINUM) POST AND WOOD POST CONNECTOR INSTALLATION If using VISTI r ALX psts, 4 x 4 wd psts, r 6 x 6 wd psts, refer t the INVISIRAIL BOLT CHART. Check yur pst layut diagram t see if yu must add spacers. Straight-Run Cnnectr Tp bracket t be installed 40 inches O/C abve deck surface fr 42 inch rail height (34 inches fr 36 inch rail height.) Re-assemble bracket using 5/32 r 4mm hex key Universal Angle Bracket Disassemble the brackets by taking ut the lcking pin and hinge screw. Tp bracket t be installed 40 inches O/C abve deck surface fr 42 inch rail height (34 inches fr 36 inch rail height.) Use InvisiRail Template t lcate exactly where cnnectrs shuld g. Use hardware prvided t attach Universal Angle Bracket t pst (stainless selftapping lags fr Vista/ALX/aluminum psts r wd screws fr wd psts.) Once the hinge is fastened t the pst, reassemble bracket and attach glass cnnectr. Use InvisiRail Template (shwn n p.16) t lcate exactly where cnnectrs shuld g. Use hardware prvided t attach cnnectr t pst (stainless self-tapping lags fr aluminum psts r wd screws fr wd psts.) D nt ver-tighten lags, causing stripping. 15

16 LITE 10 NYLON GLASS CONNECTOR INSTALLATION FOR WOOD POSTS ALX POSTS 16 Lite 10 cnnectrs are fr use with Visti, ALX psts (aluminum), wd psts r any slid flat surface EXCEPT InvisiPsts. They are nt designed fr use with InvisiPsts. Tp bracket t be installed 40 inches O/C abve deck surface fr 42 inch rail height (34 inches fr 36 inch rail height.) Use InvisiRail Template t lcate exactly where cnnectrs shuld g. Disassemble the tp cnnectr by backing ut the nyln retaining pin and sliding ff the splined prtin. Use hardware prvided t attach cnnectr t pst (stainless self-tapping screws fr Visti / ALX / aluminum psts r wd screws fr wd psts.) D nt ver-tighten tapping screws, causing stripping. Ensure cnnectrs are as parallel as pssible t the edge f the pst. Install the pen side f the tp cnnectr facing twards deck fr easier glass installatin. Lite 10 Angle Bracket Mark the bttm edge lcatin f bth tp and bttm cnnectrs. Bttm mark shuld be 3 abve flange base. Tp mark shuld be 38 15/16 abve flange base. Fasten the 45 degree bracket t the pst with the mark at the bttm f the bracket. Using #8 x 1 wd screws (nt included) attach- the Lite 10 cnnectr t the angle bracket. 45 degree angle bracket with cnnectr Template fr psitining cnnectrs n VISTI r ALX psts, square aluminum r wd psts Fr wd psts flip template upside dwn and place at base f pst n deck surface. TOP HOLE FOR BOTTOM LITE 10 CONNECTOR MIDDLE HOLE FOR TOP LITE 10 CONNECTOR LITE 10 LITE 10 MIDDLE HOLE FOR TOP LITE 10 CONNECTOR TOP HOLE FOR BOTTOM LITE 10 CONNECTOR FOR VISTI POSTS THIS SIDE DOWN SHOULD SIT ON TOP OF FLANGE

17 GLASS PANEL INSTALLATION Stainless Steel Cnnectrs Use tw shrt pieces f 2X4 s r 4X4 s, sitting n edge f the deck between the psts, t supprt the glass panels while installing. Dr shims help with fine height adjustments. Cnnectr pins need t be aligned with hles/ ntches in the glass. Lcate crrect glass panel t be installed (all panels are labeled.) Carefully pick up panel and set int psitin with ntches in glass at the bttm. Fasten tp cnnectrs first. Place pin thrugh glass and slide remaining cnnectr half int psitin. If required, shim panel until pin is psitined hrizntally, aiding in alignment f cnnectr halves. Tighten screws enugh t hld cnnectrs tgether but nt squeeze tightly n glass. Once cmpleted, check that all cnnectrs are parallel t each ther and tighten screws cmpletely. If the cnnectr halves d nt slide easily nt installed sectins, cnfirm that the cnnectr has nt been ver tightened - this wuld cause misalignment f the tw halves. The back half f cnnectr must be cmpletely flush with the frnt half t ensure the pin is in the hles in bth halves f the cnnectr. Once the pin is perfectly aligned, cmpletely tighten screws. Lite 10 Nyln Cnnectrs Lcate crrect glass panel t be installed (all panels are labeled.) Carefully pick up panel and set int psitin abve bttm cnnectrs (ntches in glass shuld be at the bttm) and push glass dwn int cnnectr until it bttms. Take tp cnnectr half and slide it int psitin, then screw pin back in. IF pin des nt screw in easily make sure there are n alignment issues. Pssible surces f errr are: ut f plumb psts, psts nt set at crrect dimensin, deck surface nt level, cnnectrs nt lcated crrectly. 17

18 TEMPLATING FOR CUSTOM STAIR GLASS Stair glass fr InvisiRail is always custm cut and takes 3-4 weeks fr prductin. Each piece f stair glass will require a template. Please ensure accuracy as yur glass will be made t the exact size/shape f yur template. Cardbard sheets are typically prvided with rders fr templating purpses. Alternatively, yu can use hardbard (ie. Masnite r similar) r plywd fr templating. Helpful tls fr templating: Bx cutter / knife t cut cardbard OR saw t cut hardbard r plywd Firm straight edge (i.e. drywall square)... the lnger the better Pen and/r sharpie Bubble level (t ensure psts are plumb) Clamps t hld template material nt psts/cnnectrs ½ drill bit t drill ut hles in template fr cnnectr pins (if using hardbard r plywd) String line t help align the tp/bttm edge f multiple panels dwn a lng staircase D nt install t clse t risers, but g as clse t step nsing as yu can. As shwn belw, the cnnectr at left is clear f the stair nsing (white line). Psitining the pst t clse t the riser will nt allw the bttm edge f the glass t be parallel t stair nsing line. YES NO STEP 2 - Clamp r hld template material in behind cnnectrs, psts. It may be helpful t rest the bttm edge f the template material n stair nsing. Trace a line indicating the inside pst edge. Trim template t fit between psts. STEP 1 - Install psts & cnnectrs. Refer t layut drawing t cnfirm pst cnfiguratin at tp f stairs, ensuring psts are plumb and are n mre than 60 O/C (hrizntally) apart. Psts shuld be installed t allw fr (near) equal sectins f glass, r whatever cnfiguratin is mst aesthetically pleasing. Fr square psts (withut predrilled hles fr cnnectrs), install the cnnectrs in similar psitins t the psts used fr the main deck. It is alright if small changes need t be made t these psitins, as the hles & ntches in the glass will be psitined where yu indicate. STEP 3 - Using a straight edge draw a line cnnecting tps f psts. This will represent the tp edge f the glass. Next, draw a line fr the bttm edge f glass. If the bttm edge 18

19 f the template is resting n the nsing, draw a line parallel t nsing s that bttm edge f glass will sit abve stair nsing. Yu shuld ensure that the bttm edge f the glass will meet cde and nt allw a 6 diameter ball t fit thrugh the pening. STEP 4 - Trace cnnectr psitins nt template then trim tp and bttm. The back edge f the rubber pads is rughly where the edge f the glass will be. If yu wish, yu can trim the sides f the template s that the material represents the exact shape & size f the glass panel. This way the template can be installed as if it were the panel. Indicate n cardbard the tp/bttm edges f glass if nt dne s already. STEP 5 - If handrail will be installed with the glass munted handrail brackets, please indicate where thse hles fr the brackets shuld be. Refer t handrail brackets if sent with initial shipment. Typically, hles are lcated apprx. 6 dwn frm tp edge f glass. Ensure lcatin will allw fr handrail t be installed at a height that passes lcal building cde. If there are multiple stair panels dwn the staircase, please indicate where the templates are lcated n the stairs (eg. upper panel, middle panel, lwer panel, etc.) Custm glass panels will be made t the exact specificatins f the template(s), except that crners are made with a ½ radius t avid sharp edges and sme hles r ntches may be mitted frm panel. Every panel shuld have at least tw details (hle r ntch). Please ensure that templates are nt damaged, warped etc. befre being sent t InvisiRail. Try t minimize the number f bends in the template if pssible. If, fr whatever reasn, there are errrs r ptential issues with the templates prvided (i.e. severely warped, curved edges, lack f inf., etc.) InvisiRail will ntify yu and may request new templates t be sent. Please write the fllwing infrmatin n yur template/s: Stre name where initial InvisiRail rder was purchased PO number/sales rder number if applicable Date templates were made and/r sent ut Cntact inf. fr creatr f templates (name, phne number, if applicable) Panel identificatin (i.e. upper panel 1 f 2, lwer panel 2 f 2, etc.) Frm the time the templates are received by InvisiRail, it typically takes 3-4 weeks until the custm panels are cmpleted and ready t ship. Templates will be duble checked against the custm panel and sent with the glass. 19

20 7/16 7/16 4 3/4 1 7/8 15/32 2 1/2 InvisiPst flange base scale 1:1 20

21 INVISIPOST POSITIONING DETAIL DIAGRAMS 1 5/8 MIN - 3 3/4 MAX t centre pst 2 t centre pst 1 RIM 3/8 3/8 MIN - 2 1/2 MAX t flange 3 t glass HOUSE HEADER r END 3 t glass 11/16 ( ) 3/8 STAIRS InvisiPst at huse r end f run scale 1:1 InvisiPst -- beside stairs scale 1:1 3 1/8 1 1/2 3/8 3 5/8 t angle bracket r 3/4 t centre pst equivalent 1 1/2 5 7/8 t angle bracket r 5 3/4 t centre pst equivalent nnthreaded bracket 3 t glass 3 5 7/8 t angle bracket r 5 3/4 t centre pst equivalent threaded bracket 3 5/8 t angle bracket r 3/4 t centre pst equivalent InvisiPst -- utside 90 split scale 1:1 w/ Universal Angle Brackets InvisiPst -- inside 90 split w/ Universal Angle brackets scale 1:1 21

22 13/16 ( ) t angle bracket r 15/16 ( ) t centre pst equivalent 3 1/2 t angle bracket r 3 3/8 t centre pst equivalent 1/ / InvisiPst -- inside 45 split scale 1:1 w/ Universal Angle brackets InvisiPst -- utside 45 split scale 1:1 w/ Universal Angle bracket 2 1/8 t angle bracket ON CENTRE 3 2 t centre pst equivalent 3/ /16 ( ) t pst face 1 3/8 t flange base 3 2 5/8 t centre pst 5/8 r 3/4 t centre pst equivalent 3/ InvisiPst -- inside 45 scale 1:1 w/ Universal Angle bracket InvisiPst -- utside 45 scale 1:1 w/ Universal Angle bracket

23 1 15/16 11/ /16 4 1/2 t angle bracket r 4 3/8 t centre pst equivalent 3 t glass 1 9/16 2 t angle bracket r 2 1/8 t centre pst equivalent 4 1/2 t angle bracket r 4 3/8 t centre pst equivalent t angle bracket r 2 1/8 t centre pst equivalent InvisiPst -- utside 90 split scale 1:1 w/ 45-degree brackets InvisiPst -- inside 90 split w/ 45-degree brackets scale 1: /16 (2.4375) t angle bracket r 2 5/16 (2.3125) t centre pst equivalent 1/2 3 1 t pst face r 1 3/8 t centre pst equivalent 3/8 3 1 r 1 1/8 t centre pst equivalent 3/8 r 1/2 t centre pst equivalent 3 InvisiPst -- utside 45 scale 1:1 w/ 45-degree bracket InvisiPst -- inside 45 scale 1:1 w/ 45-degree bracket 23

24 1/2 1/ /2 7/ /2 2 1/2 Visti Pst flange base scale 1:1 24

25 VISTI POST POSITIONING DETAIL DIAGRAMS 2 1/2 t centre pst 4 7/8 MAX - 2 1/2 MIN t centre pst 1 3/8 MIN - 2 1/2 MAX t flange HOUSE HEADER OR END 2 1/2 t centre pst 1 3/8 STAIRS VistiPst at huse r end f run scale 1:1 VistiPst -- beside stairs scale 1:1 2 1/2 2 1/2 t centre pst 1 3/8 1 3/8 2 1/2 2 1/2 2 1/2 VistiPst -- inside 90 scale 1:1 VistiPst -- utside 90 scale 1:1 25

26 2 1/2 1 t centre pst 1/8 2 1/2 2 1/2 2 1/8 3 t centre pst 5/16 ( ) r 1 7/16 ( ) fr centre pst equivalent 1 2 1/2 1 13/16 ( ) t angle bracket r 11/16 ( ) t centre pst equivalent VistiPst -- utside 45 scale 1:1 w/stainless steel cnnectrs VistiPst -- inside 45 scale 1:1 w/stainless steel cnnectrs 1 3/16 2 1/2 2 1/2 2 1/2 2 1/8 t centre pst 1 2 1/2 2 1/16 t angle bracket VistiPst -- inside 45 scale 1:1 w/ 45-degree bracket VistiPst -- utside 45 scale 1:1 w/ 45-degree bracket 26

27 1 9/16 ( ) t uter face 7/16 ( ) t centre pst 2 1/2 2 1/2 2 1/2 5/8 r 1 3/4 fr centre pst equivalent 1 3/8 2 1/2 t centre pst 2 1/2 1 3/8 VistiPst -- inside 45 scale 1:1 w/ Lite 10 cnnectrs VistiPst -- utside 45 scale 1:1 w / Lite 10 cnnectrs 27

28 5/8 5/8 2 1/2 5 3/8 2 1/2 5 ALX pst flange base scale 1:1 28

29 ALX POST POSITIONING DETAIL DIAGRAMS 2 3/4 MIN - 5 1/8 MAX t centre pst 1 1/2 MIN - 3 7/8 MAX t pst face MIN - 2 5/8 MAX t flange HOUSE HEADER OR END 2 3/4 t glass 2 3/4 1 1/2 t pst face r 2 3/4 t centre pst equivalent STAIRS ALX pst at huse r end f run scale 1:1 2 3/4 r centre f balusters ALX pst -- beside stairs scale 1:1 2 3/4 1 1/2 t pst face r 2 3/4 t centre pst equivalent 2 3/4 1 1/2 t pst face r 2 3/4 t centre pst equivalent 1/2 2 3/4 ALX pst -- inside 90 scale 1:1 ALX pst -- utside 90 scale 1:1 2 3/4 29

30 2 3/4 2 1/2 t uter face 1 t centre pst 2 3/4 2 3/ /2 t centre pst 7/16 ( ) r 1 11/16 ( ) fr centre pst equivalent 1 2 3/4 1 7/8 t angle bracket r 5/8 t centre pst equivalent ALX pst -- inside 45 scale 1:1 w / stainless cnnectrs ALX pst -- utside 45 scale 1:1 w/ stainless cnnectrs 1 11/16 ( ) t uter face 2 3/4 7/16 ( ) t centre pst 2 3/4 2 3/4 3/4 r 2 fr centre pst equivalent 2 11/16 t centre pst 1 7/16 ( ) 3/16 2 3/4 1 1/2 t angle bracket ALX pst -- inside 45 scale 1:1 w/ Lite 10 cnnectrs r t centre pst equivalent ALX pst -- utside 45 scale 1:1 w/lite 10 cnnectrs 30

31 1 3/8 t pst face 1/16 t centre pst 2 3/4 2 3/4 2 3/4 1/16 r 2 5/16 fr centre pst equivalent 2 3/8 t centre pst 1 1/8 1/8 ALX pst -- inside 45 scale 1:1 w/ 45-degree bracket 2 3/4 2 1/8 t angle bracket r 7/8 t centre pst equivalent ALX pst -- utside 45 scale 1:1 w/ 45-degree bracket 31

32 INVISIPOST FASCIA POSITIONING DETAIL DIAGRAMS FASCIA 11/16 (0.667 ) t angle bracket r 9/16 ( ) t centre pst equivalent 2 t flange 2 3/4 t angle bracket r 2 5/8 t centre pst equivalent 3 1/8 t face f pst 3 t centre pst 2 t glass FASCIA 2 2 fascia-munt SS InvisiPst - crner scale 1:1 fascia-munt SS InvisiPst inside 90 scale 1:1 2 t glass 1 t centre pst 1 t angle bracket r 1 3/8 t centre pst equivalent 1 1/8 t pst face 2 X 1 spacers between pst and angle bracket 2 t glass FASCIA 2 1/8 t centre pst 7/8 t flange 1 1/2 t angle bracket r 1 3/8 t centre pst equivalent FASCIA 2 t glass 2 32 fascia-munt SS InvisiPst utside 90 scale 1:1 fascia-munt SS InvisiPst -- inside 45 scale 1:1

33 FASCIA 3 1/4 t centre pst 2 t flange FASCIA 2 t glass 3 1/8 t face f pst STAIRS 2 t glass 1 1/2 t centre pst t flange 1/8 t angle bracket r t centre pst equivalent 2 t glass 2 3/4 t angle bracket r 2 5/8 t centre pst equivalent spacer between pst and angle bracket 2 fascia-munt SS InvisiPst -- utside 45 scale 1:1 fascia-munt SS InvisiPst -- beside stairs scale 1:1 33

34 FASCIA 11/16 (0.667 ) t angle bracket r 9/16 ( ) t centre pst equivalent 1 13/16 t flange 2 3/4 t angle bracket r 2 5/8 t centre pst equivalent 3 1/8 t face f pst 3 5/16 t centre pst 2 t glass FASCIA 2 2 fascia-munt aluminum InvisiPst - crner scale 1:1 fascia-munt aluminum InvisiPst inside 90 scale 1:1 FASCIA FASCIA 2 t glass 1 9/16 t centre pst 11/16 t flange 2 t glass /8 t angle bracket r t centre pst equivalent 2 t glass 1 1/2 t angle bracket r 1 5/16 t centre pst equivalent 1 spacer 2 t glass 2 t face f pst 2 3/16 t centre pst fascia-munt aluminum InvisiPst -- utside 45 scale 1:1 fascia-munt aluminum InvisiPst -- inside 45 scale 1:1 34

35 VISTI POST FASCIA POSITIONING DETAIL DIAGRAMS FASCIA 1 t face f pst 2 3/8 t centre pst 1 t face f pst 2 3/8 2 3/8 VistiPst fascia-munt crner scale 1:1 VistiPst fascia -- inside 90 RIM 3 1/2 gap meets cde requirements 1 5/16 ( ) t pst face 2 7/16 ( ) t centre pst VistiPst fascia-munt utside 45 crner scale 1:1 35

36 3 3/8 t centre pst 7/8 2 1/2 t centre pst 2 3/8 1/2 t equivalent 1 5/8 n centre t angle bracket 2 3/8 3/16 ( ) t 1 5/16 equivalent ( ) n centre t angle bracket 2 3/8 2 3/8 VistiPst fascia -- inside 45 scale 1:1 w/stainless steel cnnectrs Visti Pst fascia -- inside 45 scale 1:1 w/lite 10 cnnectrs 36

37 37

38 Custmer name:... Phne number:... InvisiRail dealer name:... Shipping address fr glass: Fax frm t r t sales@invisirail.cm 38

39

40 Fllw learn like Any installatin r use f the prduct must be in accrdance with all lcal zning and/r building cdes. The cnsumer assumes all risk and liability assciated with the installatin r use f this prduct. Check with lcal municipalities fr building cde requirement in yur area befre installing. sales@invisirail.cm Tll free