Low-profile Master Type (Slim Type) The thinnest possible body contributes to reduced size, height and weight of the set product

Transcription

1 RS NS Low-profile Master Type (Slim Type) The thinnest possible body contributes to reduced size, height and weight of the set product Typical Specifications Items Specifications tolerance ±0% Maximum operating voltage 00V AC, 0V DC (RSN ) 500V AC, 0V DC (RSA0N ) Operating force N Operating life 0,000 cycles Product Line Operating range 0 to + Number of resistor elements Travel Lever type Length of lever Resistance taper Minimumorder unit(pcs.) Terminal style Japan Export Products Drawing Single-unit 00 9-T (T-Bar) Note Other varieties are also available. Refer to "Other Specifications" (P.7). Packing Specifications Tray B For PC board 0, RSNS006 RSA0NS9A0K Travel Number of packages(pcs.) case /Japan case /export packing Export package measurements 0, Style PC board mounting hole dimensions (Viewed from mounting side) t= ø hole -ø.5 hole.75 6 Refer to P.7 for other specifications. Refer to P.8 for ordering products not listed. Refer to P.8 for soldering conditions.

2 RS NS/Low-profile Master Type (Slim Type) Style PC board mounting hole dimensions (Viewed from mounting side) t= ø hole -ø.5 hole Low-profile Master Type (Slim Type) / Other Specifications In addition to the products listed, we can accommodate the follow specifications. Total Resistance Variety Resistance Taper 5A B 0A Lever Types Configuration code 9-T (T-Bar) 8 t=. t=. t=. (0) (5.8) Corresponding Specification Terminal Layout / Circuit Diagram Dust cover Available Marked are specifications recommended by Alps. 7

3 Low-profile Master Type (Slim Type) / Ordering Products Not Listed When ordering product varieties that are not listed, specify referring to the examples below. Sample Part Number R S 6 0 N S 0 B 0 Travel mm A0 00mm Number of resistor elements Single-unit Lever types Code Configuration code 0 0 9T 9 -T( T- B a r) Code A 5A B B D 0A J G 00 (%) Output volt.across term.- Input volt. across term B(B) D(0A) A(5A) Code 0 0 Code Term."" Rotation travel (%) J Term.""

4 List of Varieties Type Low-profile master type Motor-driven master type N Fader Slim Type Super P Fader Motor N Fader Motor K Fader Motor V Fader RS N RS NS RS P RS N M RSA0K V RSA0VM Single-unit/Dual-unit Single-unit Single-unit/Dual-unit Single-unit/Dual-unit Single-unit/Dual-unit Single-unit Photo Travel, 00, Direction of lever Vertical Lever material Metal Resin Operating range 0 to + Operating life 0,000 cycles 00,000 cycles 00,000 cycles Available for automotive use ーーーーーー Electrical performance Life cycle Rated Power 0, 50, 00, 50 0, 0, 50 0, 50, 00, W (RSN) 0.5W (RSA0N) 5A, B, 0A 0.W (RSNS) 0.5W (RSA0NS) 0.W (Single-unit) 0.W (Dual-unit) Single-unit:B Dual-unit:Servo B Audio 5A, B, 0A 0.W (RSN M) 0.5W (RSA0N M) 0.5W B Insulation resistance 00MΩ min. 50V DC Voltage proof 50V AC for minute Center-taps Without Operating force Single-unit:0. Dual-unit:0. N N N 0.5 N 0.8±0.5N Single-unit:0.±0.5N Dual-unit:0.5 to 0.9N ー Center detent Without Mechanical performance Stopper strength 00N 0N Lever push-pull strength 50N 5N Lever wobble Both sides Lever deviation ( L) max.(one side) Terminal style Insertion Lead, Insertion Connector(Fader) Lead(Motor) Connector Page 6 9 Soldering Conditions 8 Potentiometer Cautions 9 Measurement and Test Methods Resistance Taper. Attenuation is specified for residual resistance.. "L" in the "Lever Wobble" column of the above table indicates the length of lever. 00

5 / Soldering Conditions Reference for Manual Soldering Tip Duration of Soldering time of solders RS, RS H, RS08U, RS K (Standard), RS N, RS NS, RS P, RS N M, RSA0K V (Motor terminal) 50 max. s max. time Reference for Dip Soldering Preheating Dip soldering Soldering surface Soldering Number of soldering Heating time Soldering time RS, RS H, RS N, RS NS, 00 max. min. max. 5s max. time RS P, RS N M Example of Reflow Soldering Condition Temperature profile General-use Mixer Temperature ( C ) A B C D Room Time (s) Pre-heating E max. F max. G max. H max. A B C D E F G H of reflows RS08U min. s 0s min. time. When using an infrared reflow oven, solder may sometimes not be applied. Be sure to use a hot air reflow oven or a type that uses infrared rays in combination with hot air.. The s given above are the maximum s at the terminals of the potentiometer when employing a hot air reflow method. The of the PC board and the surface of the potentiometer may vary greatly depending on the PC board material, its size and thickness. Ensure that the surface of the potentiometer does not rise to 50 C or greater.. Conditions vary to some extent depending on the type of reflow bath used. Be sure to give due consideration to this prior to use. 8