Chip Attenuator. Chip Attenuator

Size: px

Start display at page:

Download "Chip Attenuator. Chip Attenuator"

Colin Booker
5 years ago
Views:

1 Chip Attenuator 00 Type: EXBAT (Unbalanced p type) Type: EXBAB (Balanced O type) n Features EXBAT type : Unbalanced p type l Unbalanced p type attenuator circuit in one chip(1.0 mm 1.0 mm) l Mounting occupation area reduction : about 50 % reduction compared with an attenuator circuit consisting of three 00 chip resistors, almost equal to an attenuator circuit consisting of three 001 chip resistors l Mounting cost reduction : Mounting times times Õ 1 time l Attenuation : 1 db to 10 db EXBAB type : Balanced O type l Balanced O type attenuator circuit in one chip(1.0 mm 1.0 mm) l Mounting occupation area reduction : about 6 % reduction compared with an attenuator circuit consisting of four 00 chip resistors, about 6 % reduction compared with attenuator circuit consisting of four 001 chip resistors l Mounting cost reduction : Mounting times times Õ 1 time l Attenuation : 0 db to 10 db n Recommended Applications l Attenuation / level control / impedance matching of high frequency signals of communication equipment; cellular phones(gsm, CDMA, PDC, etc.), PHS, PDA, for example.

2 n Explanation of Part Numbers l EXBAT type : Unbalanced p type E X B A T A R X l EXBAB type : Balanced O type E X B A B G R 8 X n Attenuation-Frequency Characteristics (typical) (EXBAT type)

3 n Construction EXBAT EXBAB n Circuit Configuration EXBAT EXBAB n (not to scale) EXBAT EXBAB L W T A B 1.00 ± ± ± ±0.10 L W T A B 1.00 ± ± ± ±0.10 C P(typical value) 0.5 ± C P(typical value) 0.0 ± <Marking Configuration> The bar marking for recognizing terminal direction is located on the side of terminal.

4 n Ratings Item Attenuation Value EXBAT 1 db, db, db, db, 5 db, 6 db, 10 db* 1 db, db, db, db, 5 db : ± 0. db Attenuation Value Tolerance 6 db, 10 db : ± 0.5 db Characteristic Impedance Power Rating Frequency Range 50 W* 0.0 W /package DC to GHz VSWR (Voltage Standing Wave Ratio) Number of Resistors Number of Terminals 1. Max. resistors terminals Category Temperature Range (Operating Temperature Range) -55 C to +15 C *Please inquire about the other attenuator value / characteristics impedance. EXBAB 0 db, 1 db, db, db, 6 db, 10 db* 0 db to db : ± 0.8 db 6 db : ± 1.0 db 10 db : ±.0 db 100 W, 00 W, 00 W* 0.0 W /package DC to.5 GHz 1. Max.(typical value) 1.5 Max.(0 db, typical value) resistors terminals -55 C to +15 C Power Derating Curve For resistors operated in ambient temperature above 70 C, power rating shall be derated in accordance with the figure on the right. n Packaging Methods l Standard Quantity Type (inches) Thickness Weight (mg) Punched (Paper) Taping ( mm Pitch) EXBAT/AB (00) pcs./reel n Taping l Taping Reel l Punched (Paper) Taping fa fb fc W T min. 1.0 ± ± ±.0 Ð.0 A B W F E 1.0 ± ± ± ± ±0.10 P0 P1 P fd0 T.00 ± ± ± ±0.10 <Product direction in the chip pocket of carrier tape> Products shall be sealed so as to locate the terminal 1 and on the side of feeding direction in the chip pocket.

5 nrecommend Land Pattern a b c d to to 1.5 Safety Precautions 1. Soldering Recommendation for soldering method is noted below. lreflow soldering Precautions and recommendations are described below. lplease inquire with us when you use the different conditions. lplease measure a temperature of terminations and study the solderability for every type of board before using. Rising temperature I The normal to Preheating temperature 0 s to 60 s Preheating 10 C to 160 C 60 s to 10 s Rising temperature II Preheating to 00 C 0 s to 0 s Main heating (cf. The limits of resistance to reflow soldering heat) Gradual cooling 00 C to 100 C 1 C/s to C/s (Reflow soldering shall be within two times.) l Flow soldering We cannot recommend the flow soldering, because a solder bridge may occur owing to narrow 0.65 mm pitch. l Iron soldering 1Solder at 80 C max. and seconds max. with the soldering iron tip. The soldering iron tip shall not touch the protective coating of the part. l Use rosin type flux. Do not use high-activity flux (the chlorine content is 0. wt % or more). l Allow enough preheating so that the difference of soldering temperature and temperature of surface of the part is 100 C or less. This temperature difference shall be kept in rapid cooling by immersion into solvent. l Use of more solder results in more mechanical stress to the part resulting in cracking or impaired characteristics. Avoid excessive amount of solder.. Cleaning l Residual flux after board washing may cause solder migration. Carefully check the status of board washing. Study the type and amount of flux to be used when no washing is made. Study the type of water-soluble flux and cleaning agent and drying condition when water washing is done. Confirm they will not cause any trouble.. Others l Take necessary precautions to avoid any abnormal stress caused by bending of board. l Do not use the product in dewy atmosphere.

6 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Panasonic: EXB-AB1CR8X EXB-ABCR8X EXB-ABCR8X

MLCC APPLICATION GUIDE

MLCC APPLICATION GUIDE 1/10 No. Process Condition 1 Operating Condition (Storage) 1) The capacitor must be stored in an ambient temperature between 5 ~ 40 with a relative humidity of 20 ~ 70%. The products