PRODUCT SPECIFICATION
|
|
- Whitney Carr
- 5 years ago
- Views:
Transcription
1 SCOPE 1.25mm 9(& 2$ 2 This specification covers the 1.25 mm PITCH WIRE TO BOARD CONNECTOR (DUAL TYPE) series PRODUCT NAME AND PART NUMBER <N $ D/P Plug Terminal Product Name <N 4X B+È;R( Plug Housing (With Positive Lock) -Q - O Ç X;O Straight Receptacle Assembly XA Embossed Tape Packaging For **00 NÉ-ÇXP O Ç X;O Right Angle Receptacle Assembly XA Embossed Tape Packaging For **00 LEAD FREE LEAD FREE LEAD FREE LEAD FREE LEAD FREE Part Number * : Refer to the drawing. RATINGS AND APPLICABLE WIRES Item Standard Rated Voltage (MAX.) 50 V [ AC ( rms) / DC ] AWG#26 1.0A Rated Current ( MAX. ) and Applicable wires AWG#28 1.0A mm Insulation O.D. Ambient Temperature Range (Operating and Non-operating) -25 C ~ + 85 C *1 *1 : Including terminal temperature rise. Not freeze to low temperature A 1~12 A RELEASED ECN No. J /11/16 N.NISHI DESIGN CONTROL J STATUS 1.25mm PITCH WIRE TO BOARD CONNECTOR DUAL TYPE WRITTEN BY: N.NISHII CHECKED BY: K.ASAKAWA APPROVED BY: YO.ITO DATE : YR/MO/DAY 2007/11/16 1 of 12 EN-37(019)
2 PERFORMANCE hPa hPa Standard atmospheric conditions: Unless otherwise specified, the standard range of atmospheric conditions for making measurements and tests are as follows. Ambient temperature : 5 to 35 Relative humidity : 25% to 85% Air pressure : 860hPa to 1060hPa If there is any doubt about the results, measurements shall be made by the following test conditions. Ambient temperature : 20 1 Relative humidity : 63% to 67% Air pressure : 860hPa to 1060hPa. Electrical performance Item Test Condition Requirement 2$ 20mV 10mA (JIS C ) Insulation Dielectric Strength Mate connectors and measured by dry circuit, 20mV MAX., 10mA. (JIS C ) 2$ $ D/P $ D/P Ç DC 250V (JIS C /MIL-STD ) Mate connectors and apply 250V DC between adjacent terminal or ground. (JIS C /MIL-STD-202 Method 302) 2$ $ D/P $ D/P Ç AC(rms) 500V ( ) 1 2 (JIS C /MIL-STD ) Mate connectors and apply 500V AC(rms) for 1 minute between adjacent terminal or ground. Trip current 2mA. (JIS C /MIL-STD-202 Method 301) 20 milliohms MAX. 100 Megohms MIN. No Breakdown on Crimped Portion $ D/P 20mV 10mA Crimp the applicable wire to the terminal, measured by dry circuit, 20mV MAX., 10mA. 5 milliohms MAX. A SEE 1 of 12 2 OF 12
3 . Mechanical Performance Item Test Condition Requirement mm Insertion and Withdrawal Force Crimping Pull out Force $ D/P Terminal Insertion Force <N$ D/P Plug Terminal Retention Force O $ D/P Rec. Terminal Retention Force Insert and withdraw connectors at the speed rate of mm/minute. (JIS C ) $ D/P 25 3mm Fix the crimped terminal, apply axial pull out force on the wire at the speed rate of 25 3mm/minute. (JIS C ) $ D/P 4X Insert the crimped terminal into the housing. <N4X 1 5mm/sec <N$ D/P Apply axial pull out force at the speed rate of 1 5mm/sec on the plug terminal assembled in the plug housing. O 4X 25±3mm $ D/P Apply axial pull out force at the speed rate of 25±3mm/minute on the rec. terminal assembled in the rec. housing. AWG#26 AWG#28 Refer to paragraph 6 9.8N{1.0kgf}MIN. 9.8N{1.0kgf}MIN. 4.9N { 0.5kgf } MAX. 4.9N {0.5 kgf} MIN. 1.96N {0.2 kgf} MIN. 4XR( 4X 19.6N{2.0kgf} Housing Lock Strength Mated connectors, and apply axial pull out force of 19.6N. A SEE 1 of 12 3 OF 12
4 Environmental Performance and Others Item Test Condition Requirement Repeated Insertion / Withdrawal When mated up to 30 cycles repeatedly by the rate of 10 cycles per minute. / Temperature Rise All crimp-style terminal shall be connected in a direct series by minimum AWG. The temperature rise shall be measured by thermocouple when the terminal reaches terminal equilibrium under rated voltage / rated current. (However with resistive load) Temperature Rise 30 C MAX Vibration Mechanical Shock DC 1mA Hz/ 1.52mm 2 (MIL-STD ) Mate connectors and subject to the following vibration conditions, for a period of 2 hours in each of 3 mutually perpendicular axes, passing DC 1mA during the test. Amplitude : 1.52mm P-P Frequency : 10~55~10 Hz in 1 minute. Duration : 2 hours in each X.Y.Z.axes. (MIL-STD-202 Method 201) DC 1mA 6 490m/s { 50G } 11ms 3 (JIS C /MIL-STD ) Mate connectors and subject to the following shock conditions. 3 shocks shall be applied along 3 mutually perpendicular axes, passing DC 1 ma current during the test. (Total of 18 shocks) Test pulse : Half Sine Peak value : 490 m/s 2 (50 G) Duration : 11 ms (JIS C /MIL-STD-202 Method 213) Discontinuity Discontinuity 1 microsecond MAX. 1 microsecond MAX. 40 milliohms MAX A SEE 1 of 12 4 OF 12
5 Item Test Condition Requirement 2$ 85±2 C 96 1 (JIS C /MIL-STD ) Heat Mate connectors and expose to 85 2 for 96 hours. Upon completion of the exposure period, the test specimens shall be conditioned at ambient room conditions for 1 hour, after which the specified measurements shall be performed. (JIS C /MIL-STD-202 Method 108) 40 milliohms MAX 2$ 25±3 C 96 1 (JIS C ) Cold Mate connectors and expose to for 96 hours. Upon completion of the exposure period, the test specimens shall be conditioned at ambient room conditions for 1 hour, after which the specified measurements shall be performed. (JIS C ) Humidity 2$ 40±2 C 90~ (JIS C /MIL-STD ) Mate connectors and expose to 40 2, relative humidity 90 to 95% for 96 hours. Upon completion of the exposure period, the test specimens shall be conditioned at ambient room conditions for 1 to 2 hours, after which the specified measurements shall be performed. (JIS C /MIL-STD-202 Method 103) Insulation Dielectric Strength Must meet Must meet A SEE 1 of 12 5 OF 12
6 Item Test Condition Requirement ÉP Temperature Cycling 2$ 25 3 C ÉP 5ÉP (JIS C0025) Mate connectors and subject to the following conditions for 5 cycles. Upon completion of the exposure period, the test specimens shall be conditioned at ambient room conditions for 1 to 2hours, after which the specified measurements shall be performed. 5 cycles of : a) 25 3 C 30 minutes b) C 30 minutes (JIS C0025) 2$ 35±2 C 5±1% 48 (JIS C /MIL-STD ) Salt Spray Mate connectors and expose to the following salt mist conditions. Upon completion of the exposure period, salt deposits shall be removed by a gentle wash or dip in running water, after which the specified measurements shall be performed. NaCl solution Concentration : 5 1 % Spray time : 48 4 hours Ambient temperature : 35 2 (JIS /MIL-STD-202 Method 101) SO 2 Gas 2$ 40±2 C 50±5ppm 24 Mated connectors and expose to the conditions of 50 5ppm SO2 gas ambient temperature 40 2 for 24 hours. A SEE 1 of 12 6 OF 12
7 Item Test Condition Requirement ÇXG0Ç Ammonia gas 2$ 28 ÇXG0 Ç Mated connectors and expose to the conditions of NH3 gas evaporating from 28% Ammonia solution for 40 minutes. 78 without damage such as cracks or other breaks 40 milliohms MAX Solderability 0.5mm Dip soldertails into the molten solder [held at degree centigrade] up to 0.5mm from the bottom of the housing for 4 5 seconds. Solder Wetting 90 90% of immersed area must show no voids,pin holes. O:R Reflow soldering method Reference reflow condition at 7 clause to Soldering Heat 3 0.2mm C + $ Soldering iron method 0.2mm from terminal tip Solder Temperature : C Soldering Time :3 4 seconds MAX. ( ): Reference Standard { }: Reference Unit A SEE 1 of 12 7 OF 12
8 Refer to the drawing. PRODUCT SHAPE, DIMENSIONS AND MATERIALS INSERTION / WITHDRAWAL FORCE No. of CKT 20 UNIT N {kgf} Insertion (MAX.) Withdrawal (MIN.) 1st 6th 30th 1st 6th 30th 19.6 { 2.0 } 14.7 { 1.5 } 14.7 { 1.5 } 0.98 { 0.1 } 0.78 { 0.8 } 0.78 { 0.8 } 30 N {kgf} 24.5 { 2.5 } 19.6 { 2.0 } 19.6 { 2.0 } 1.47 { 0.15 } 1.27 { 0.13 } 1.27 { 0.13 } N {kgf} { 3.0 } { 2.5 } { 2.5 } { 0.2 } { 0.18 } { 0.18 } R( Released lock, and measure. { } : Reference Unit A SEE 1 of 12 8 OF 12
9 O:R REFLOW CONDITION 9 N: TEMPERATURE CONDITION GRAPH ( ) (SOLDER JOINT PART) O:R O:R (O:R ) + P 2ÉP NOTE : Please check the mount condition (reflow soldering condition) by your own devices beforehand, because the condition changes by the soldering devices, p.c.boards, and so on. Although tail of terminal and nail may discolors, a solderability does not have a problem NOTES <N&( There is no influence in the product performance though the black spot etc. might be confirmed to the plastic part of this product and the shade might be different. ELV RoHS ELV and RoHS Compliant COMPLIANCE WITH ENVIRONMENTAL DIRECTIVE A SEE 1 of 12 9 OF 12
10 INSTRUCTION UPON USAGE 2$ 1.25 W/B CONN. DUAL 2$ AS Please refer to the manual of the 1.25 W/B connector. DUAL series for the detailed handling of the connector. AS O 4X 4X R( Please push the part directed by FIG.1 at the time of mate. It may damage, when electric wires or lock part of the receptacle housing are pushed. WIRE PUSH PUSH O 4X REC. HOUSING 1 FIG.1 2$ R( R( 5 R( R( When unmated connectors, positive locks shall be released. Mounting performance of coplanarity shall not contain the influence of the warpage of the mounting board. A SEE 1 of OF 12
11 O:R O:R The coplanarity assurance of this product is a guarantee alone before mounting, and the coplanarity during and after the empty reflow is not guaranteed. + O?Ç H(< G P. Please conduct it under the condition of the specifications when repairing by hand soldering iron after mounting. In the case of practicing beyond the condition, the backlash, the change in the contact gap, the deformation of the mold and the melting, etc. may cause a damage. 6$ X In the case of changing our recommended board pattern size and designing, please consult in advance because it may cause a fatal defect. O:R F( MO Strand, etc. may be generated on the terminal plating part according to the reflow condition, however, there is no influence in the product performance. O:R Discoloration may be generated in the resin part according to the reflow condition, however, there is no influence in the product performance. 2$ O:R N2O:R O:R N2O:R Soldering wicking: "This connector assumes the mounting by an air reflow. In the case of mounting by the N2 reflow, there is a risk of the soldering wicking. The separate evaluation is necessary for mounting by the N2 reflow." F$PC T 0.11mm F$PC Description of size of thickness of recommended metal mask and the aperture ratio. And the metal mask of thickness of T=0.11mm and the aperture ratio of 100% is used in our evaluation. A SEE 1 of OF 12
12 RECORD DATE EC NO. WRITTEN: CH K: A RELEASED 07/11/16 J N.NISHI K.ASAKAWA A SEE 1 of OF 12
Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. PRODUCT SPECIFICATION 1. SCOPE 1.0mm9(&FPC 2$ This specification covers
More informationPRODUCT SPECIFICATION
CONNECTOR CONNECTOR 1 of 6 CONNECTOR 1.0 SCOPE This Product Specification covers the dip type for 13pins slimline SATA receptacle connector. 2.0 PRODUCT DESCRIPTION 2.1 PRODUCT NAME AND SERIES NUMER(S)
More informationThis specification covers the requirements for product performance, test methods and quality assurance provisions of FG Terminal.
DESIGN OBJECTIVES The product described in this document has not been fully tested to ensure conformance to the requirements outlined below. Therefore AMP Ltd makes no representation or warranty, express
More informationPRODUCT SPECIFICATION
Page 1 Page 2 1.0 SCOPE. This specification covers performance, tests and quality requirements for the SIM Card Connector SIM 2055 (Receiver Type, 6-Pin, SMT, 1.8 & 2.2mm Profiles). 2.0 PRODUCT NAME AND
More informationBlower Motor 3P Connector
1. Scope Blower Motor P Connector 1.1 Content This specification covers the requirements for product performance, test methods and quality assurance provisions of Blower Motor P connector. Applicable product
More informationProduct Data Sheet PD-0053-A
Product Data Sheet PD-0053-A 3M Mini D Ribbon (MDR) Connector MDR Surface Mount 102XX-1210 XE 102XX-1S10 XE Page: 1 of 11 Table of Contents 1.0 SCOPE...2 2.0 PRODUCT TESTED...2 3.0 GENERAL CONDITIONS...2
More informationProduct Series Specification Document
Product Series 3.96mm pitch board-to-board connectors - Socket SCOPE This document covers 3.96mm socket connectors. The connector will perform to the specifications outlined. All tests have been performed
More informationPRODUCT SPECIFICATION 1 SCOPE APPLICABLE STANDARDS CATALOG NO. STRUCTURE..3 4 CONNECTOR SHAPE, DIMENSIONS AND MARTERIALS..
1 of 1 A Table of Contents: 1 SCOPE.. 3 2 APPLICABLE STANDARDS..... 3 3 CATALOG NO. STRUCTURE..3 4 CONNECTOR SHAPE, DIMENSIONS AND MARTERIALS..3 5 ACCOMMOD CONDUCTORS (CIC).....3 6 PACKAGING CONDITION........3
More informationPRODUCT SPECIFICATION FOR Micro SIM +Nano SIM/Micro SD (T/F)Card Connector SERIES
Page 1 of 5 1.0 SCOPE This Specification covers Micro SIM +Nano SIM/Micro SD Card Connector SERIES 2.0 APPLICABLE DOCUMENTS AND SPECIFICATIONS See sales drawings and other sections of this specification
More informationProduct Data Sheet PD-0037-B
Product Data Sheet PD-0037-B 3M Shielded Compact Ribbon (SCR) Connector 3M Shielded Compact Ribbon (SCR) Boardmount Right Angle 36110-2220 XX 3 Electronic Solutions Division Page: 1 of 12 Table of Contents
More informationProduct Specification
Product Specification 2013-10-21 FPC Connector 0.5mm Pitch SMT Type Bottom Contact H:2.0 Update List: Item Update Description Rev. Issued Date Revisor 1 New Edit A 2013/10/21 DLITY Prepared By DLITY Rechecked
More informationPRODUCT. Part. A1 Micro USB USB3140. Rev. Page. Description Doc USB3140.
1 PREL LIM MI IN AR RY 1.0 SCOPE. This specification covers performance, tests and quality requirements for the Receptacle (Type B, SMT, Vertical)..0 NAME AND PART NUMBER. Receptacle, 5 Pins, SMT, Type
More informationQualification Test Report
Qualification Test Report 501-97 28Jun10 Rev E Connector, Shielded, Miniature Circular DIN, PCB Mounted 1. INTRODUCTION 1.1. Purpose Testing was performed on Tyco Electronics Mini DIN Printed Circuit Board
More informationMOLEX TAIWAN LTD ( GC ) TITLE : SINGLE PORT UP-RIGHT TYPE USB CONNECTOR
SINGLE PORT UP-RIGHT TYPE USB CONNECTOR 971205 1 of 8 1.0 SCOPE This specification covers the USB series product. 2.0 APPLICABLE DOCUMENTS The following documents form a part of this specification to the
More informationPRELIMINARY PRODUCT SPECIFICATION. Part Number Product Description Doc Number
Page 1 PRELIMINARY Page 2 1.0 SCOPE. This specification covers performance, tests and quality requirements for the USB Type C Receptacle range. USB4050, USB4055, USB4060, USB4065. 2.0 PRODUCT NAME AND
More informationSPECIFICATION AND PERFORMANCE CHARACTERISTICS OF SCA-2 CONNECTOR SERIES
SPECIFICATION AND PERFORMANCE CHARACTERISTICS OF SCA-2 CIRCUIT ASSEMBLY CORP. 18 THOMAS STREET, IRVINE, CA 92618-2777 Page No. 1 CONTENTS CLAUSE PAGE 1.0 SCOPE. 4 1.2 Description. 4 2.0 APPLICABLE DOCUMENTS
More informationDATA SHEET Metal Element Current Sensing Chip Resistor (Jumper) CLS Series
DATA SHEET Metal Element Current Sensing Chip Resistor (Jumper) 5% SIZE: 0805,1206 & 2512 RoHs Compliant January 19, 2017 V.5 DS-ENG-009 Page: 2 of 14 1. SCOPE 1.1 This specification is applicable to lead
More informationAPR 10 Rev. A
1. Introduction 1.1 Testing was performed on the DDR SODIMM SOCKET 200P to determine if it meets the requirement of Product Specification, 108-78628 1.2 Scope This report covers the electrical, mechanical
More informationDDR4 SODIMM Socket 0.5mm Pitch 260Pos
1. Introduction 1.1 Testing was performed on DDR4 SODIMM SOCKET 260P to determine if it meets the requirement of Product Specification, 108-115122 Rev.A. 1.2 Scope This report covers the electrical, mechanical
More information3M Pak 10 Plug, PK10 series PK10-XXXPX-X-DA. 3M Pak 10 Socket, PK10 series PK10-XXXSX-X-DA
Page of 8 M Pak 0 Plug, PK0 series PK0-XXXPX-X-DA M Pak 0 Socket, PK0 series PK0-XXXSX-X-DA Product Specification Revised 08-0- Page of 8 Table of Contents Title Page.............................................................................
More informationSMD Switch SI-C3436A General specification. Soldering conditions Reflow Soldering condition. Standard Reel Dimensions (mm) Packing specification
SMD Switch SI - C3436A - 7017 Features External Dimensions : 3.4mm x 3.6mm, Height 0.70mm Suitable for thinner and lighter portable devices Suitable for water proof devices Reflow soldering Package With
More informationWIESON TECHNOLOGIES CO., LTD.
TABLE OF CONTENT 1. Scope.... 2 2. Reference Documents. 2 3. Material and Components.... 2 4. Design and Construction.... 2 5. Rating.. 2 6. Performance and Test Descriptions. 2 7. Test Requirements and
More information2W, 2816, SL Type Low Resistance Chip Resistor (Lead / Halogen Free)
2W, 2816, SL Type (Lead / Halogen Free) 1. Scope This specification applies to 4.2mm x 7.1mm size 2W, fixed metal foil current sensing resistors used in electronic equipment. 2. Features / Applications
More informationSERIAL ATA POWER CONNECTOR 1.27 mm PITCH
: 1.27 mm PITCH TBLE OF CONTENTS 1.0 SCOPE 2.0 PPLICBLE DOCUMENTS 3.0 MTERIL SPECIFICTIONS 3.1 DESIGN ND CONSTRUCTION 3.2 MTERILS 4.0 PERFORMNCE ND TEST 5.0 TEST REQUIREMENTS ND PROCEDURES SHT 1 2 3 4
More information3M Pak 50 Boardmount Socket, P50 series P50-XXXS-XXX-EA. 3M Pak 50 Boardmount Plug, P50 series P50-XXXP-XXX-EA
Page of 8 3M Pak 50 Boardmount Socket, P50 series P50-XXXS-XXX-EA 3M Pak 50 Boardmount Plug, P50 series P50-XXXP-XXX-EA Product Specification 78-50-0-7 Revised 08-09- Page of 8 Table of Contents Title
More information3/4W, 2010 Low Resistance Chip Resistor
1. Scope 3/4W, 2010 This specification applies to 2.5mm x 5.0mm size 3/4W, fixed metal film chip resistors rectangular type for use in electronic equipment. 2. Type Designation RL2550 L - Where (1) (2)
More informationPMLCAP. Polymer Multi Layer Capacitor Specification Sheet RUBYCON CORPORATION PML DIVISION. PMLCAP ST series RPR Rubycon PART No. Drawing No.
To Polymer Multi Layer Capacitor Specification Sheet Rubycon PART No. ST series Drawing No. RPR-0024 Issued Date October 15, 2008 PML DIVISION 2932, MOTOOSHIMA, MATSUKAWA-MACHI, SHIMOINA-GUN, NAGANO-KEN,
More information1W, 1206, Low Resistance Chip Resistor (Lead free / Halogen Free)
1W, 1206, (Lead free / Halogen Free) 1. Scope This specification applies to 1.6mm x 3.2mm size 1W, fixed metal film chip resistors rectangular type for use in electronic equipment. 2. Type Designation
More informationProduct Data Sheet PD-0036-B. 3M PC Boardmount Plug and Receptacle, 2 mm 95X Series
Product Data Sheet PD-0036-B 3M PC Boardmount Plug and Receptacle, 2 mm 95X Series Page: 1 of 7 1.0 SCOPE...2 2.0 PRODUCT TESTED...2 3.0 GENERAL CONDITIONS...2 3.1 Test Specimens...2 3.2 Standard Test
More informationSC-1000/2000 ROTARY CODED SWITCHES S C T B FEATURES PART NUMBER DESIGNATION. Please refer to the LIST OF PART NUMBERS when placing orders.
SC-00/2000 RoHS compliant INTERNAL STRUCTURE SC-00 / 2000 series 4 2 3 6 7 5 FEATURES Part name Material Flammability Housing Metallic spring O ring Insert rotor Polyphenylenesulphide Stainless (SUS 30)
More informationSpezifikation Z56-xx Series ZIF FFC/FPC Connector 0,5mm Pitch Double Contact H1,96mm Piano
1 Scope This Specification covers the construction and characteristics of 0,5mm Pitch FFC and FPC (Flat Flexible Cable and Flat PCB Cable ) of Z56-xx ZIF Connector Series. The part shall satisfy the following
More informationSD-1000/2000 ROTARY CODED SWITCHES S D T B FEATURES PART NUMBER DESIGNATION. Please refer to the LIST OF PART NUMBERS when placing orders.
SD-00/2000 RoHS compliant INTERNAL STRUCTURE SD-00 / 2000 series Part name Material Flammability FEATURES Housing Polyphenylenesulphide UL9V-0 Metallic spring O ring Insert rotor Base Stainless (SUS 30)
More informationJun-2012 Rev A
Design Objective 108-57912 01-Jun-2012 Rev A MINI USB CONNECTOR, RECEPTACLE, VERTICAL, DIP, B TYPE 1. SCOPE 1.1. Contents This specification covers the performance, tests and quality requirements for the
More informationQualification Test Report. Modular Plugs, Unshielded and Shielded
Qualification Test Report 501-131013 26 JAN 16 Rev. A Modular Plugs, Unshielded and Shielded 1. INTRODUCTION 1.1. Purpose Testing was performed on modular plugs to determine their conformance to the requirements
More informationTITLE STATUS SPEC. NO. DATE PAGE NO. 3.5Φ EARPHONE JACK 4 POLEs / 2 SWITCH GENERAL SMT TYPE BS S-01
Specification TITLE STATUS SPEC. NO. DATE PAGE NO. 3.5Φ EARPHONE JACK 4 POLEs / 2 SWITCH GENERAL SMT TYPE BS123-000S-01 1 OF 4 1999/09/30 1. GENERAL SCOPE THIS SPECIFICATION COVERs THE GENERAL REQUIREMENTs
More informationPRODUCT SPECIFICATION
1 of 10 H 1.0 GENERAL THIS SPECIFICATION COVERS.039 INCHES VERTICAL DDR II SOCKETS WITH BLANKED / FORMED CONTACT DESIGNED FOR PRINTED WIRING BOARD TO DUAL IN-LINE MEMORY MODULE INTERCONNECTION. IN ALL
More informationCFP PIANO SWITCHES (FULL PITCH) FEATURES APPLICATIONS PART NUMBER DESIGNATION C F P T B
CFP RoHS compliant INTERNA STRUCTURE FEATURES Part name Cover Material Flammability Slider Housing Polyamide U94V- Slider contact APPICATIONS Fixed contact Terminal pin Copper alloy, Gold-plated Piano
More informationData sheet FIXED CHIP RESISTORS; RECTANGULAR TYPE & WIDE TERMINATION. AEC-Q200 qualified. RoHS COMPLIANCE ITEM Halogen and Antimony Free
No.: TWMC K HTS-0001 /4 Date: 2017. 4. 21 Data sheet Title: FIXED CHIP RESISTORS; RECTANGULAR TYPE & WIDE TERMINATION Style: TWMC32, 50, 63 AEC-Q200 qualified RoHS COMPLIANCE ITEM Halogen and Antimony
More informationSPECIFICATIONS. Multi-layer Chip Ferrite Bead GZ Series Customer Part Number. [ New Released, Revised] SPEC No.: GZ110000
Sunlord Specifications for Multi-layer Chip Ferrite Bead Page 1 of 16 SPECIFICATIONS Customer Product Name Sunlord Part Number Multi-layer Chip Ferrite Bead G Series Customer Part Number [ New eleased,
More informationWW25R ±1%, ±5%, 2W Metal plate low ohm power chip resistors Size 2512 (6432)
WW25R ±1%, ±5%, 2W Metal plate low ohm power chip resistors Size 2512 (6432) Current Sensing Type Automotive AEC Q200 compliant *Contents in this sheet are subject to change without prior notice. Page
More informationWW25Q ±1%, ±5%, 1W Metal plate low ohm power chip resistors Size 2512 (6432)
WW25Q ±1%, ±5%, 1W Metal plate low ohm power chip resistors Size 2512 (6432) Current Sensing Type Automotive AEC Q200 compliant *Contents in this sheet are subject to change without prior notice. Page
More informationSuper High AUTO (SHA) Series
PART NO. SFI1206SA240-1R5J 1.1 Technology Data Symbol Value Unit Maximum allowable continuous DC voltage V DC 12 V Breakdown voltage measured Vv 24(±10%) V Maximum clamping voltage V CLAMP < 40 V Maximum
More informationAREP Series Aluminum Solid Electrolytic Capacitors Aluminum Solid Electrolytic Capacitors
Features -Super low ESR, high ripple current capability -Rated voltage:6.3~35vdc -Endurance:5,000 hours at 105ºC -Suitable for DC-DC converters, voltage regulators and decoupling applications -RoHS Compliant
More informationLow Inductance Ceramic Capacitor (LICC)
Low Inductance Ceramic Capacitor (LICC) LICC(Low Inductance Ceramic Capacitor) is a kind of MLCC that is used for decoupling in High Speed IC. The termination shape of LICC is different from that of MLCC.
More informationDATA SHEET General Purpose Thick Film Chip Resistor CR Series
Towards Excellence in Quality, Service & Innovation DATA SHEET General Purpose Thick Film Chip Resistor 1% TO 5%, TCR -200 TO +600 SIZE: 01005/0201/0402/0603/0805/1206/1210/2010/2512 RoHs Compliant Jan
More informationData sheet FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE AND HIGH POWER ANTI SURGE. AEC-Q200 qualified
No.: RPCH-K-HTS-0001 /2 Date: 2017.4.21 Data sheet Title: Style: FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE AND HIGH POWER ANTI SURGE RPCH16,20,32,35 AEC-Q200 qualified RoHS COMPLIANCE ITEM Halogen
More informationData sheet FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE ANDULTRAHIGH VOLTAGE. AEC-Q200 qualified. RoHS COMPLIANCE ITEM Halogen and Antimony Free
No.: RZC K HTS 0001 /6 Date: 2017. 4. 21 Data sheet Title: FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE ANDULTRAHIGH VOLTAGE Style: RZC50, 63 AEC-Q200 qualified RoHS COMPLIANCE ITEM Halogen and Antimony
More informationCFP PIANO SWITCHES (FULL PITCH) FEATURES APPLICATIONS PART NUMBER DESIGNATION C F P T B. RoHS compliant
RoHS compliant INTERNA STRUCTURE FEATURES RoHS compliant High-reliability 1 Part name Cover Slider Housing Material Polyamide Flammability U9V- Slider contact APPICATIONS Communication devices, Air-conditioning
More informationData sheet FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE RMC1/32,1/20,1/16S,1/16,1/10,1/8,1/4,1/2,1. AEC-Q200 qualified (Without RMC1/32)
No.: RMC-K-HTS-0006 /11 Date: 2017. 4. 18 Data sheet Title: Style: RMC1/32,1/20,1/16S,1/16,1/10,1/8,1/4,1/2,1 AEC-Q200 qualified (Without RMC1/32) RoHS COMPLIANCE ITEM Halogen and Antimony Free Note: Stock
More informationCeramic PTC Thermistor: PT Series
Sensor Features. RoHS compliant 2. Small size 3. Very fast reaction time 4. Wide range of protection temperatures 5. Stable over a long life 6. Operating temperature range: 0 ~ Ts+25 C (V=Vmax) 7. Agency
More informationFIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE & HIGH OHM. RoHS COMPLIANCE ITEM Halogen and Antimony Free
Spec. No.: RHC K HTS 0001 /8 Date: 2017. 1. 10 Specification Title: FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE & HIGH OHM Style:,20 RoHS COMPLIANCE ITEM Halogen and Antimony Free Product specification
More informationPLASTIC FILM CHIP CAPACITOR TYPE ECHU1(C) Operating temperature range
1/ 16 P. 1. SCOPE This specification covers the requirement for metallized polyphenylene sulfide dielectric fixed chip capacitor for use in inverter circuit for LCD back light and use in electronic equipments.
More informationTEA10402V15A0 Engineering Specification
TEA10402V15A0 Engineering 1. Scope This specification is applied to electrostatic discharge (ESD) protection. It is designed to protect the high-speed data lines against ESD transients. It has very low
More informationPECIFICATIONS Model TC03 Page 3 1. Scope This specification applies to the ceramic type trimmer capacitor using ceramic as a dielectric.
PECIFICATIONS Model TC3 Page 3 1. Scope This specification applies to the ceramic type trimmer capacitor using ceramic as a dielectric. 2. Main characteristics Table 1 Part No. TC3Z5H169B TC3Z1H169B TC3R1H169B
More informationAll part numbers in the coding below start with "TC-" and end with "203"
1. Scope: This specification for approval relates to 2. Type designation: The type designation shall be in the following form : All part numbers in the coding below start with "TC-" and end with "203"
More informationDATA SHEET Anti-Sulphur Thick Film Chip Resistor SAS(A/B) Series
DATA SHEET Anti-Sulphur Thick Film Chip Resistor SAS(A/B) Series 0.5% TO 5.0%, TCR -200 TO +400 SIZE: 0201/0402/0603/0805/1206/1210/2010/2512 RoHs Compliant May 08, 2017 V.4 Page: 2 of 1. SCOPE 1.1 This
More informationPLASTIC FILM CHIP CAPACITOR TYPE ECHU(X)
1 / 17 P 1. SCOPE This specification covers the requirement for metallized polyphenylene sulfide dielectric fixed chip capacitor for use in electronic equipments. 2. PRODUCT NAME Plastic film chip capacitor
More informationPREJECTION INDUSTRIAL CORP. 百泉工業股份有限公司
: 1 OF 11 1. Features High performance (Isat) realized by metal dust core. Performance low resistance,high current rating. Low loss realized with low DCR. Frequency range : up to (1.0 MHz). 100% lead (pb)
More informationFMS series Metal Strip Shunt Lead Free Current Sensing Resistors
1. Features......2 2. Applications...... 2 3. Dimension and construction.. 2 4. Power Derating Curve....3 5. Rating.3 6. Part Number.. 3 7. Marking / Soldering..4 8. Reliability Performance..5 9. Packing.
More informationST-32 SURFACE MOUNT CERMET TRIMMERS (SINGLE TURN) S T E T A ( 1 2 ) FEATURES PART NUMBER DESIGNATION
SURFACE MOUNT CERMET TRIMMERS (SINGLE TURN) ST- RoHS compliant INTERNAL STRUCTURE 7 6 5 4 9 8 FEATURES 4 5 6 7 8 9 Part name Wiper Cover Housing Terminal pin Base element O ring Rotor Electrode Resistive
More information0805 CG 102 J 500 N T
NPO/COG for General-use is class I high frequency capacitor, its capacitance is very stable, almost will not change along with the temperature, voltage and time. Specially be suitable for high frequency
More informationFeatures Instant light (less than 100ns) Lead free reflow soldering RoHS compliant Cool beam, safe to the touch
ProLight PM2G-1LYE-WSL 1W 370nm + 400nm Power LED Technical Datasheet Version: 1.3 Features Instant light (less than 100ns) Lead free reflow soldering RoHS compliant Cool beam, safe to the touch Typical
More information50 TZV 1500 M JDE VB 18X21.5
EXTENDED BASE FEATURES: VB- VIBRATION BASE AEC-Q200 SURFACE MOUNT ROHS COMPLIANT APPLICATIONS: AUTOMOTIVE POWER INDUSTRIAL SPEC: VALUE: MPN :50 TZV 1500 M JDE VB 18X21.5 VDC 50 CAPACITANCE 1500μF +/- 20%
More informationCeramic PTC Thermistor: PPL Series
Features. RoHS compliant 2. Leaded type 3. Voltage rating: 270V ac ~500V ac 4. Resistance range:0~000ω 5. Stable over a long time 6. Operating temperature range: -20 ~ +85 C (V=V max ) -40 ~ +25 C (V=0)
More informationCommon mode ESD filter LXES**D series Document No. LX Rev1.2
Common mode ESD filter LXES**D series Document No. LX 1-1126 Rev1.2 1. This specification shall be applied to the ESD Protection Device. LXES11DAA2-135 LXES21DAA4-136 LXES11DAA2-137 LXES21DAA4-138 LXES21DAA4-14
More informationReference Only Spec. No. JEFL243B 0003F-01 P 1/ 6
Spec. No. JEFL243B 0003F-01 P 1/ 6 DC Common Mode Choke Coil PLT09HN2003R0P1B Reference Specification 1. Scope This reference specification applies to DC Common Mode Choke Coil (PLT09H Series). 2. Part
More informationNo Item Code Description Series Reference. Thickness. M B min (mm) T (mm) code. See Thickness Specification Reference Table below
FEATURE A wide selection of sized is available (0201 to 2225) High capacitance in given case size Capacitor with lead-free termination (pure Tin) RoHS and HALOGEN compliant. Application: DC to DC converter.
More informationPOE INTERNATIONAL CORPORATION. SPECIFICATION OF MULTI-LAYER RADIAL-LEADED TYPE CAPACITOR Ver: 8 Page: 1
SPECIFICATION OF MULTI-LAYER RADIAL-LEADED TYPE CAPACITOR Ver: 8 Page:. Scope: Its specification applies to Radial Series Ceramic Capacitor. 2.How to order: CODE: U RD2 R 02 K T Rated Voltage Code:U =
More informationMain Applications CCTV Wireless communication Indoor Lighting Outdoor Lighting
ProLight PK2N-2LJE-SD 2W Infrared 850 Power LED Technical Datasheet Version: 1.6 Features Instant light (less than 100ns) Lead free reflow soldering RoHS compliant Cool beam, safe to the touch Superior
More informationRF Transformer (Stabilized Matching Device) SMST15 series
1 Features RF Transformer Stabilized Matching Device is RF impedance matching components. You can adjust impedance matching easily between antenna and feeding point, when you use RF Transformer. RF Transformer
More informationNP0 Dielectric Non-Magnetic Multilayer Ceramic Capacitors C 0603 CG 101 J 500 P
EIA High Non-Magnetic Multilayer Ceramic Capacitors NP0 Dielectric Non-Magnetic Multilayer Ceramic Capacitors Product Features Non-Magnetism, Suitable for MRI Part Numbering C 0603 CG 101 J 500 P T 1 2
More informationMetal Oxide Varistor:TVM-B Series
Features. RoHS & Halogen Free (HF) compliant. EIA size: 040 ~ 0 3. Operating voltage: 5.5Vdc ~ 85Vdc 4. High surge suppress capability 5. Bidirectional and symmetrical V/I characteristics 6. Multilayer
More informationElectric Double Layer Capacitors Product Specification. To. : DATE : SPECIFICATION WRITTEN CHECKED APPROVED
To. : DATE : 200... SPECIFICATION PRODUCT MODEL : STARCAP : DCS series WRITTEN CHECKED APPROVED 1 Index Page No. ITEM etc. 1 Cover Page 2 Index 1. Scope 2. Part Number System 3 3. Product Model Name 4.
More informationCPTC Thermistor: PP Series
Features. RoHS compliant 2. Lead type 3. Voltage rating: 270Vac~500Vac 4. Resistance range:0~000ω 5. Stable over a long time 6. Operating temperature range: -20 ~ +85 C (V=Vmax) -40 ~ +25 C (V=0) 7. Agency
More informationSUNSTAR 传感与控制 TEL: FAX: Hall Sensor As of Nov SUNSTAR 自动化
As of Nov. 2004 E-MAIL: INTRODUCTION is a magnetic sensor using Hall effect, generating output voltage directly proportional to magnetic field. FEATURE AND APPLICATION Feature - SAMSUNG is highly sensitive
More informationChip Inductors. LCCM Series Chip Common Mode Filter FEATURES CONSTRUCTION
FEATURES Small wire wound chip inductor with ferrite core and 2 common mode lines. Highly effective in noise suppression High common-mode impedance at noise band an low differential mode impedance at signal
More informationSpecifications: The shelf life of product is within 6 months. Features Description Test Conditions Requirements
Specifications: Operating Temperature Range : -25 C to+70 C Storage Temperature Range : -30 C to +80 C Current Range : 50mA, 12V DC The shelf life of product is within 6 months Test Sequence: Appearance
More informationRS INDUSTRY LIMITED. RS Chip Array ESD Suppressor APPROVAL SHEET. Customer Information. Part No. : Model No. : COMPANY PURCHASE R&D
APPROVAL SHEET Customer Information Customer : Part Name : Part No. : Model No. : COMPANY PURCHASE R&D Vendor Information Name: RS INDUSTRY LIMITED Part Name ARRAY TYPE MULTILAYER VARISTOR Part No. RS
More information1.2 Scope: This specification is applied Noise Filter STC-D series supplied
1.0 PURPOSE / SCOPE 1.1 Purpose: To define the quality of Noise Filter STC-D series. 1.2 Scope: This specification is applied Noise Filter STC-D series supplied by SMI-ED. 2.0 GENERAL 2.1 Reference 2.1.1
More informationAD Scope: Its specification applies to Radial Series Ceramic Capacitor. 2.How to order: CODE
1 1. Scope: Its specification applies to Radial Series Ceramic Capacitor. 2.How to order: CODE U AD10 R 102 K T Rated Voltage CodeT = 25 VDC U = 50 VDC Size Code : refer to the description in 3 Dielectric
More informationFrelTec GmbH. Multilayer Chip Ferrite Bead SMD
GmbH Mathildenstr. 10A 82319 Starnberg Germany SMD 3/21/2017 1/12 GmbH www.freltec.com SPECIFICATION Part Number 198 05 * 151 * S * Q * E02 Type Size Nominal Impedance Material Rated Current Tolera nce
More informationProsperity Dielectrics Co., Ltd. 1 ACS-1045 Rev15
1. DESCRIPTION MLCC consists of a conducting material and electrodes. To manufacture a chip-type SMT and achieve miniaturization, high density and high efficiency, ceramic condensers are used. WTC high
More informationALUMINUM ELECTROLYTIC CAPACITORS REFERENCE SHEET
TO Messrs. AVNET ABACUS ALUMINUM ELECTROLYTIC CAPACITORS REFERENCE SHEET CUSTOMER PART No. Rubycon PART No. 35 TLV 470 M 12.5X13.5 DRAWING No. RERS 011758 ISSUE No. 1 ISSUE DATE 25 AUGUST 2010 ENGINEERING
More informationWIP201610P Series Engineering Specification
RoHS Pb WIP201610P Series Engineering 1. Scope Feature Low Profile: 2.0 mm 1.6 mm 1.0 mm. Magnetically shielded structure to accomplish high resolution in EMC protection. Halogen free, Lead Free, RoHS
More informationMain Applications Backlighting Signaling Exterior Automotive Lighting Automotive Interior Lighting
ProLight PJ2N-FFPE-A 0.5W PC Amber Power LED Technical Datasheet Version: 1.1 Features Good color uniformity Lead free reflow soldering RoHS compliant Instant light (less than 100ns) No UV Main Applications
More informationFrelTec GmbH. Thick Film Chip Resistor SMD Low Ohm
GmbH Mathildenstr. 10A 82319 Starnberg Germany Thick Film Chip Resistor SMD Low Ohm 9/10/2012 1/13 GmbH www.freltec.com SPECIFICATION Part Number 016 05 * 001k * J * T05 ** *** Type Size Value Tolerance
More informationCHIP RESISTOR. Chip Resistors Selection Guide. General Purpose Chip Resistor. Zero Ohm Jumper Resistor. Chip Resistor Array MAX WORKING VOLTAGE
Chip Resistors Selection Guide General Purpose Chip Resistor SIZE/ mm POWER RATING MAX WORKING VOLTAGE TOLERANCE RESISTANCE RANGE 0402 1.00*0.50 0603 1.60*0.80 1/10W 0. 0805 2.00*1.25 1/8W 1 0. 1206 3.10*1.60
More informationConfigurations: Dimension (mm) A (max) Item IRS IRS
Configurations: FEATURES Magnetically shielded construction. Compact and thin. Put the electrode with ferrite core directly, a small surface area allow a high mounting. Shielding Drum Choke for good in
More informationOpen-mode Design Capacitors
Open-mode Design Capacitors HOW TO ORDER OP 32 B 103 K 201 C T Series Size Dielectric Capacitance Tolerance Rated voltage Termination Packaging OP=Open-mode 21=0805 (2012) 31=1206 (3216) B=X7R Two significant
More informationMain Applications T8/T5 tube LED bulb Indoor/Outdoor Commercial and Residential Architectural
ProLight PJ2N-2FPE-A2 2W PC Amber Power LED Technical Datasheet Version: 1.4 Features Good color uniformity Lead free reflow soldering RoHS compliant Instant light (less than 100ns) No UV Main Applications
More informationSM-3/31 SURFACE MOUNT CERMET TRIMMERS. S M - 3 T W 1 k ( ) FEATURES PART NUMBER DESIGNATION
SURFCE MOUNT CERMET TRIMMERS SM-/ RoHS compliant INTERNL STRUCTURE 6 9 8 7 FETURES 6 7 8 9 Part name Housing Base element Electrode Resistive element dhesive Wiper Terminal pin Rotor gear Shaft Material
More informationMetal Oxide Film Resistors Axial Connections Metal Oxide Film Resistors 1/4W, 5% Components
Metal Oxide Film Resistors Axial Connections Metal Oxide Film Resistors 1/4W, 5% Components High safety standard, high purity ceramic core Excellent non-flame coating Stable performance in diverse environment,
More informationFrelTec GmbH. Multilayer Chip Ferrite Bead SMD
GmbH Mathildenstr. 10A 82319 Starnberg Germany SMD 5/16/2016 1/12 GmbH www.freltec.com SPECIFICATION Part Number 19C 03 * 151 * A50 D * Q * T04 _ Type Size Impedance Rated Current Material Toler ance Packing
More informationWW12C, WW08C, WW06C, WW04C, WW02C. Low ohm chip resistors ( power ) Size 1206, 0805, 0603, 0402, 0201
WW12C, WW08C, WW06C, WW04C, WW02C ±5%, ±1%, ±0.5% Low ohm chip resistors ( power ) Size 1206, 0805, 0603, 0402, 0201 *Contents in this sheet are subject to change without prior notice. Page 1 of 8 ASC_WWxxC_V05
More information東莞永力電業有限公司 YUNG LI CO., LTD REVISION RECORD YUNG LI. Customer : Parts No. : Draw No. : CY-U0003 TC02CCCCYY-95 CUSTOMER APPROVED
東莞永力電業有限公司 YUNG LI CO., LTD Da Pu Industrial Zone, Gang Zi, Changping Town, Dong Guan City, Guangdong 523571 China.P.R.C TEL:0769-3396797~8 E-mail: sales@yung-li.com FAX:0769-3396796 Description : YP-11/YC-13
More informationReference Only. Spec. No. JENF243G 0004G-01 P 1 / 12. Ferrite Bead Inductor BL02/BL03 Series
Spec. No. JENF243G 0004G-01 P 1 / 12 1. Scope Ferrite Bead Inductor B02/B03 Series Reference Specification This reference specification applies Ferrite Bead Inductor (Radial Type). 2. Part Numbering (Ex.)
More informationINPAQ. Specification. WIP252012S L Series. Product Name. Power Inductor. Size EIAJ Global RF/Component Solutions
WIP252012S L Series Specification Product Name Series Power Inductor WIP252012S L Series Size EIAJ 2520 WIP252012S L Series Engineering Specification 1. Scope Feature High saturation current realized by
More informationSurface Mount Power Resistor Thick Film Technology
Surface Mount Power Resistor Thick Film Technology DESIGN SUPPORT TOOLS click logo to get started Models Available FEATURES AEC-Q200 qualified 35 W at 25 C case temperature Surface mounted resistor - TO-263
More information*Contents in this sheet are subject to change without prior notice.
MULTILAYER CERAMIC CAPACITORS Automotive Capacitor Arrays Series (MY) Qualified to 4 x 0402, 4 x 0603 Sizes NP0 & X7R Dielectrics Halogen Free & RoHS Compliance *Contents in this sheet are subject to change
More informationSp e c i f i c a t i o n
K M Y Last update: 2015.2.6 No.RC-K-HTS-0001-13 (Uncontrolled copy) Sp e c i f i c a t i o n (Reference) Style: RC1/4,1/2 RoHS COMPLIANCE ITEM Product specification contained in this specification are
More information