Application Guidelines
|
|
- Gwendolyn Simmons
- 6 years ago
- Views:
Transcription
1
2 Application Guidelines PERFORMANCE CHARACTERISTICS SUNIL ELECTRONICS IND. CO., LTD.
3 Application Guidelines SUNIL ELECTRONICS IND. CO., LTD.
4 Application Guidelines When using Plastic film capacitors, pay strict attention to the following; 1. DC Rated voltage vs. AC Rated voltage Rated voltage of capacitor is normally specified at DC voltage except for special type. When DC rated capacitor is operated in AC circuit, Please consult our engineering department for assistance in these application. RATED VOLTAGE Rated voltage vs. Operating temperature Use the plastic film capacitors according to the specified operating temperature range. Usage at room temperature will ensure longer life. When operating Metallized Polyester Film Capacitors(Series 230S) at high temperature range(max. 105 ), the rated voltage shall be derated to operating temperature. However, in case of Metallized Polypropylene Film Capacitors(Series 430S), they shall be operated within the specified temperature range since their heat shrinkage is much greater than Metallized Polyester Film. Dielectric Type Rated Temperature 310S, 910S Polyester Dipe 230S, 230M S Polypropylene Dipe 510S, 430S 530S, 598S 435D, 460S Box 530B, 598B 436D Operating temperature Operating temperature is specified as a sum of ambient temperature and inherent temperature rise. Especially at high frequency operation, temperature of capacitor rises inherently. For such an application, make sure that the temperature at capacitor surface is within the operating temperature range. SUNIL ELECTRONICS IND. CO., LTD.
5 Application Guidelines 4. Inherent temperature rise When capacitor is operated in AC circuit, especially at high frequency, temperature of capacitor rises inherently. In case temperature rises to high, performance of capacitor may be deteriorated or damaged. The inherent temperature rise at no air circulation(ambient temperature at 40 )shall be within a value specified follow. (1) Metallized Polyester Film Capacitors (230S Series) Within ± 15 (2) Metallized Polypropylene Film Capacitors (430S Series) Within ± 15 (3) Range of a working temperature A working temperature of a capacitor, which is calculated from (Ambient temperature) + (Temperature rise due to radiation heat from other heat sources), has been specified by type. When using a capacitor, check that a working temperature comes within specified limits. When used in a high-frequency AC circuit, a capacitor generates heat due to a current running through the capacitor. And when the self-heat generation is large, the capacitor may deteriorate or there is the risk break down by heat. When using a capacitor, make sure that your requirements are within a working temperature and a specified value of self-temperature rise shown below. Dielectric Self-Temperature rise Type Metallized polypropylene capacitor Within D, 436D, 460S, 430S Polypropylene capacitor Within 5 510S, 530S, 598S, 530B, 598B Metallized polyester capacitor Within M, 230S Polyester capacitor Within S, 330S Polyester & Polypropylene capacitor Within 7 910S 5. General precautions (1) Soldering conditions When soldering, high temperature and long time process may result in deterioration of electric characteristics or short-circuit. Please pay attentions to the handing of capacitors. SUNIL ELECTRONICS IND. CO., LTD.
6 Application Guidelines (2) Shock to capacitors Attention must be paid so that any sharp objects like air-driver, soldering iron, pincette edge and etc. mat not stick strongly to surface of capacitors, Otherwise short circuit, etc, will occur. (3) Load to lead wire If excessive force is applied to the lead wires, it may be broken or its connections with the internal may be affected. (4) Charging/Discharging If used in circuits in which charge and discharge are frequently repeated, the capacitance value may crop or the capacitor may be damaged. Please consult our engineering department for assistance in these applications. SUNIL ELECTRONICS IND. CO., LTD.
7 Application Guidelines Soldering work (1) Soldering of a capacitor with leads 1) When soldering a capacitor with leads by se of a soldering iron or a soldering bath, heat is conducted to the interior of the capacitor. There for, solder in accordance with the following conditions. If dipping a capacitor into solder twice, the second dipping shall be carried after a temperature of the capacitor goes back to room temperature.(time to leave a capacitor at room temperature: For about 30 minutes) 2) If soldering a capacitor together with a chip-type component which has been mounted on a pc board, conditions vary. Contact us. (2) Soldering for CHA type capacitors 1) Reflow Soldering 1 The maximum temperature in preheating shall be 165 or less, and the time shall be within 70 seconds. 2 Soldering at 230 or more shall be preformed within 30 seconds. 3 The maximum temperature shall be A temperature specified here is one measured on a surface of a capacitor. 2) Flow Soldering 1 The maximum temperature in preheating shall be 150 or less, and the time shall be within 180 seconds. 2 Solder time shall be within 5 seconds. 3 The maximum temperature shall be 250 3) Iron Soldering 1 Mount a capacitor, being careful not to allow soldering iron to touch a capacitor directly. 2 After getting solder molten on a land, put a capacitor on it. 3 Remove a soldering iron as soon molten solder conforms to the capacitor. 4 The maximum temperature of the soldering iron tip and soldering time shall be 270 and 4 seconds, and a capacitor shall be mounted at minimal thermal capacitor. 5 Avoid reusing capacitors which have been mounted on a board once. SUNIL ELECTRONICS IND. CO., LTD.
8 Application Guidelines (3) Soldering of CAN-type capacitors 1) Reflow soldering 1 Mount a capacitor, being careful not to allow a soldering iron to touch a capacitor directly. 2 After getting solder molten on a land, put a capacitor on it. 3 Remove a soldering iron as soon as molten solder confirms to a capacitor. 4 The maximum temperature on the soldering iron tip and soldering time shall be 260 and 4 seconds. 5 Avoid reusing capacitors which have been mounted on a board once. SUNIL ELECTRONICS IND. CO., LTD.
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
Percentage tp the rated volt. Temperature ( )
1 Instructions for handling For use of any type of capacitor, you are recommended to obtain individual specification in advance and use it within the limits specified thereby. Use beyond such limits may
More informationMLCC APPLICATION GUIDE
MLCC APPLICATION GUIDE 1/10 No. Process Condition 1 Operating Condition (Storage) 1) The capacitor must be stored in an ambient temperature between 5 ~ 40 with a relative humidity of 20 ~ 70%. The products
More informationMLCC APPLICATION GUIDE
MLCC APPLICATION GUIDE 1/11 No. Process Condition 1 Operating Condition (Storage) 1) The capacitor must be stored in an ambient temperature between 5 ~ 40 with a relative humidity of 20 ~ 70%. The products
More informationPLASTIC FILM CAPACITORS
PLASIC FILM CAPACIORS APPLICAION GUIDELINES FOR PLASIC FILM CAPACIORS 1.Circuit Design (1) Please make sure that the environmental and mounting conditions in which the capacitor will be exposed are within
More informationApplication Guidelines For Tantalum Electroilytic Capacitors
For obtaining the most stable quality and sufficient Performance of the tantalum electrolytic capacitors,appropriate use must be made.before use,confirm the use conditions and rating performance of the
More informationPMLCAP. Polymer Multi Layer Capacitor Specification Sheet RUBYCON CORPORATION PML DIVISION. PMLCAP ST series RPR Rubycon PART No. Drawing No.
To Polymer Multi Layer Capacitor Specification Sheet Rubycon PART No. ST series Drawing No. RPR-0024 Issued Date October 15, 2008 PML DIVISION 2932, MOTOOSHIMA, MATSUKAWA-MACHI, SHIMOINA-GUN, NAGANO-KEN,
More information3 CONDUCTIVE POLYMER ALUMINUM ELECTROLYTIC CAPACITORS
3 CONDUCTIVE POLYMER ALUMINUM ELECTROLYTIC CAPACITORS Hi-CAP (Conductive Polymer Aluminum Electrolytic Capacitor) Hi-CAP is an electrolytic capacitor that uses a highly electric conductive polymer as it
More informationSPECIFICATION FOR APPROVAL INDEX
SPECIFICATION FOR APPROVAL INDEX COVER PAGE INDEX. 0 SCOPE...1 EXPLANATION OF PART NUMBER 1 CIRCUIT DIAGRAM & DIMENSION...1 SPECIFICATION..... 2-3 TAPING PACKAGE AND LABEL MARKING 4-5 PRECAUTIONS FOR HANDLING.....6-8
More informationElectric Double Layer Capacitors Product Specification. To. : DATE : SPECIFICATION WRITTEN CHECKED APPROVED
To. : DATE : 200... SPECIFICATION PRODUCT MODEL : STARCAP : DCS series WRITTEN CHECKED APPROVED 1 Index Page No. ITEM etc. 1 Cover Page 2 Index 1. Scope 2. Part Number System 3 3. Product Model Name 4.
More informationPLASTIC FILM CHIP CAPACITOR TYPE ECHU(X)
1 / 17 P 1. SCOPE This specification covers the requirement for metallized polyphenylene sulfide dielectric fixed chip capacitor for use in electronic equipments. 2. PRODUCT NAME Plastic film chip capacitor
More informationTEA10402V15A0 Engineering Specification
TEA10402V15A0 Engineering 1. Scope This specification is applied to electrostatic discharge (ESD) protection. It is designed to protect the high-speed data lines against ESD transients. It has very low
More information1W, 1206, Low Resistance Chip Resistor (Lead free / Halogen Free)
1W, 1206, (Lead free / Halogen Free) 1. Scope This specification applies to 1.6mm x 3.2mm size 1W, fixed metal film chip resistors rectangular type for use in electronic equipment. 2. Type Designation
More informationRS INDUSTRY LIMITED. RS Chip Array ESD Suppressor APPROVAL SHEET. Customer Information. Part No. : Model No. : COMPANY PURCHASE R&D
APPROVAL SHEET Customer Information Customer : Part Name : Part No. : Model No. : COMPANY PURCHASE R&D Vendor Information Name: RS INDUSTRY LIMITED Part Name ARRAY TYPE MULTILAYER VARISTOR Part No. RS
More information1.2 Scope: This specification is applied Noise Filter STC-D series supplied
1.0 PURPOSE / SCOPE 1.1 Purpose: To define the quality of Noise Filter STC-D series. 1.2 Scope: This specification is applied Noise Filter STC-D series supplied by SMI-ED. 2.0 GENERAL 2.1 Reference 2.1.1
More informationPLASTIC FILM CHIP CAPACITOR TYPE ECHU1(C) Operating temperature range
1/ 16 P. 1. SCOPE This specification covers the requirement for metallized polyphenylene sulfide dielectric fixed chip capacitor for use in inverter circuit for LCD back light and use in electronic equipments.
More informationApproval sheet. WLBD2012 Chip Bead. *Contents in this sheet are subject to change without prior notice.
WLBD2012 Chip Bead *Contents in this sheet are subject to change without prior notice. Page 1 of 8 ASC_ WLBD2012 Series_V5.0 Jun. 2017 FEATURES 1. Closed magnetic circuit. APPLICATIONS 1. Noise reduction
More informationApproval sheet. WLBD1005 Chip Bead. *Contents in this sheet are subject to change without prior notice.
WLBD1005 Chip Bead *Contents in this sheet are subject to change without prior notice. Page 1 of 8 ASC_ WLBD1005 Series_V4.0 Jun. 2017 FEATURES 1. Closed magnetic circuit. APPLICATIONS 1. Noise reduction
More informationChip tantalum capacitors
Chip tantalum capacitors TCO series Case TCO Series Case Features () ) Conductive polymer used for the cathode material. 2) Ultra-low ESR. (/ compared with the conventional type) 3) Screening by thermal
More informationChip tantalum capacitors (Fail-safe open structure type)
TCFG1C6M8R Chip tantalum capacitors (Fail-safe open structure type) TCFG Series Case Features 1) Safety design by open function built - in. 2) Wide capacitance range 3) Screening by thermal shock. Dimensions
More informationNo Item Code Description Series Reference. Thickness. M B min (mm) T (mm) code. See Thickness Specification Reference Table below
FEATURE A wide selection of sized is available (0201 to 2225) High capacitance in given case size Capacitor with lead-free termination (pure Tin) RoHS and HALOGEN compliant. Application: DC to DC converter.
More informationApproval sheet. WLBD1608 Chip Bead. *Contents in this sheet are subject to change without prior notice.
WLBD1608 Chip Bead *Contents in this sheet are subject to change without prior notice. Page 1 of 8 ASC_ WLBD1608 Series_V4.0 Sep. 2016 FEATURES 1. Closed magnetic circuit. APPLICATIONS 1. Noise reduction
More informationChip tantalum capacitors (Fail-safe open structure type)
TCFG0J106M8R Chip tantalum capacitors (Fail-safe open structure type) TCFG Series Case Features 1) Safety design by open function built - in. 2) Wide capacitance range 3) Screening by thermal shock. Dimensions
More informationRS INDUSTRY LIMITED. RS Chip Single ESD Suppressor APPROVAL SHEET. Customer Information. Part No. : Model No. : COMPANY PURCHASE R&D
APPROVAL SHEET Customer Information Customer : Part Name : Part No. : Model No. : COMPANY PURCHASE R&D Vendor Information Name: Part Name RS INDUSTRY LIMITED Chip ESD Part No. RS 0402-5V500S Lot No. PART
More informationWCAP-AS5H Aluminum Electrolytic Capacitors
A Dimensions: [mm] B Recommended hole pattern: [mm] D1 Electrical Properties: Properties Test conditions Value Unit Tol. Capacitance 0.25V; 120Hz C 10 µf ± 20% Rated voltage U R 16 V (DC) max. Leakage
More informationApproval sheet. WLBD0603 Chip Bead. *Contents in this sheet are subject to change without prior notice.
WLBD0603 Chip Bead *Contents in this sheet are subject to change without prior notice. Page 1 of 8 ASC_ WLBD0603 Series_V2.0 Sep. 2016 FEATURES 1. Closed magnetic circuit. APPLICATIONS 1. Noise reduction
More informationPLASTIC FILM CHIP CAPACITOR TYPE ECWUC2J
1/16 P. 1. SCOPE This specification covers the requirement for metallized polyethylene naphthalate dielectric fixed chip capacitor for use in xdsl/dc blocking and electronic equipment. 2. PRODUCT NAME
More informationWIP201610P L Series Engineering Specification
RoHS Pb WIP16P L Series Engineering 1. Scope Feature High saturation current realized by material properties and structure design Low DC resistance to achieve high conversion efficiency and lower temperature
More informationWIP252012P L Series Engineering Specification
RoHS Pb WIP212P L Series Engineering 1. Scope Feature High saturation current realized by material properties and structure design Low DC resistance to achieve high conversion efficiency and lower temperature
More informationElectronics Corp. Multi-Layer Ceramic Capacitor. Lead-free termination is in compliance with the requirement of green plan and ROHS.
X5R, X7R Dielectrics Features A monolithic structure ensures high reliability and mechanical strength. High capacitance density. A wide range of capacitance values in standard case size. Suitable for high
More informationLow Inductance Ceramic Capacitor (LICC)
Low Inductance Ceramic Capacitor (LICC) LICC(Low Inductance Ceramic Capacitor) is a kind of MLCC that is used for decoupling in High Speed IC. The termination shape of LICC is different from that of MLCC.
More informationWLBD1608HC High Current Chip Bead
WLBD1608HC High Current Chip Bead *Contents in this sheet are subject to change without prior notice. Page 1 of 7 ASC_ WLBD1608HC Series_V5.0 Jun.2017 FEATURES 1. Closed magnetic circuit. 2. High current
More informationApplications. Capacitance Tolerance G = ±2% J = ±5%
Surface Mount Metallized PPS Film Capacitor LDB, Unencapsulated Stacked Chip, Size 1206 1812, 16 and 50 VDC Overview Polyphenylene sulphide (PPS) film capacitor for surface mounting. Applications Typical
More informationApplications. Capacitance Code (pf) First two digits represent significant figures. Third digit specifies number of zeros.
AC Line EMI Suppression and RC Networks P410 Series, Integrated Resistor, Metallized Impregnated Paper, Class X1, 300 VAC Overview Applications The P410 Series is constructed of multilayer metallized paper
More informationWIP201610P Series Engineering Specification
RoHS Pb WIP201610P Series Engineering 1. Scope Feature Low Profile: 2.0 mm 1.6 mm 1.0 mm. Magnetically shielded structure to accomplish high resolution in EMC protection. Halogen free, Lead Free, RoHS
More informationApplications. Capacitance Code (pf) First two digits represent significant figures. Third digit specifies number of zeros.
AC Line EMI Suppression and RC Networks P409 Series, Integrated Resistor, Metallized Impregnated Paper, Class X2, 275 VAC Overview Applications The P409 Series is constructed of multilayer metallized paper
More informationINPAQ. Specification. WIP252012S L Series. Product Name. Power Inductor. Size EIAJ Global RF/Component Solutions
WIP252012S L Series Specification Product Name Series Power Inductor WIP252012S L Series Size EIAJ 2520 WIP252012S L Series Engineering Specification 1. Scope Feature High saturation current realized by
More informationNP0 Dielectric Non-Magnetic Multilayer Ceramic Capacitors C 0603 CG 101 J 500 P
EIA High Non-Magnetic Multilayer Ceramic Capacitors NP0 Dielectric Non-Magnetic Multilayer Ceramic Capacitors Product Features Non-Magnetism, Suitable for MRI Part Numbering C 0603 CG 101 J 500 P T 1 2
More information1. INTRODUCTION 2. FEATURES 3. APPLICATIONS 4.HOW TO ORDER
1. INTRODUCTION General Purpose Multilayer capacitors supplied in bulk or tape & reel package are ideally suitable for thick film hybrid circuits and automatic surface mounting on any printed circuit boards.
More information3/4W, 2010 Low Resistance Chip Resistor
1. Scope 3/4W, 2010 This specification applies to 2.5mm x 5.0mm size 3/4W, fixed metal film chip resistors rectangular type for use in electronic equipment. 2. Type Designation RL2550 L - Where (1) (2)
More informationReference Specification
Reference Specification High Voltage Ceramic Capacitor DHRB5AD221M1CB Issued Date: November 14, 2012 Product specifications in this drawing are subject to change or our products described in this drawing
More informationW (mm) Parameter NPO Temperature Wave X7R Temperature Wave
F E A T U R E S Small size Excellent Break down voltage, low DF Suit to re-flow soldering, wave soldering, hand soldering A P P L I C A T I O N S SMD is widely used in Analog & Digital Modems, LAN/WAN
More informationG P L 4 7 M V
1. Scope These specifications specify GPL series of the Aluminum Solid Capacitors with Conductive Polymer electrolyte. 2. Applicable standards KS C 6421(W), KS C 6035, except as specified in this specification.
More information5mm Silicon PIN Photodiode, T-1 3/4 PD333-3B/H0/L2
Features Fast response time High photo sensitivity Small junction capacitance Pb free This product itself will remain within RoHS compliant version. Description is a high speed and high sensitive PIN photodiode
More informationSpecification of V-PORT XXXX-X-V05 Series
1 Scope Specification of V-PORT-0402 -XXXX-X-V05 Series This specification is applied to ESD and EMI protection for I/O port, for example, VGA, US etc. The customer designed part number drawing take precedence
More informationPECIFICATIONS Model TC03 Page 3 1. Scope This specification applies to the ceramic type trimmer capacitor using ceramic as a dielectric.
PECIFICATIONS Model TC3 Page 3 1. Scope This specification applies to the ceramic type trimmer capacitor using ceramic as a dielectric. 2. Main characteristics Table 1 Part No. TC3Z5H169B TC3Z1H169B TC3R1H169B
More informationReference Specification
Reference Specification High Voltage Ceramic Capacitor DHRB34C221M1FB Issued Date: March 18, 2014 Product specifications in this drawing are subject to change or our products described in this drawing
More informationMetal Oxide Varistor:TVM-B Series
Features. RoHS & Halogen Free (HF) compliant. EIA size: 040 ~ 0 3. Operating voltage: 5.5Vdc ~ 85Vdc 4. High surge suppress capability 5. Bidirectional and symmetrical V/I characteristics 6. Multilayer
More informationSCM Series Supercapacitor Modules Series-Connected Supercapacitors
The new series of cylindrical electrochemical double-layer capacitors offers excellent pulse power handling characteristics based on the combination of very high capacitance and very low. Used by themselves
More informationPRODUCT SPECIFICATION
SCOPE 1.25mm 9(& 2$ 2 This specification covers the 1.25 mm PITCH WIRE TO BOARD CONNECTOR (DUAL TYPE) series PRODUCT NAME AND PART NUMBER
More informationEVERLIGHT ELECTRONICS CO., LTD.
Lead (Pb) Free Product - RoHS Compliant Feature Piranha package. Colorless clear resin. Low thermal resistance Packaged in tubes for automatic insertion equipment. Total flux: 7150 to 14250 mlm at 70mA.
More informationSPECIFICATION. 1. Scope This specification applies ferrite Chip common mode filters C3-2012F-Series to be delivered to user.
C C3-202F-Series. Scope This specification applies C3-202F-Series to be delivered to user. 2. Product Identification C3-202 F - 900-2P - T () (2) (3) (4) (5) (6) () Product name (2) Shapes and dimensions
More informationSPECIFICATION FOR APPROVAL
SPECIFICATION FOR APPROVAL THICK FILM CHIP RESISTOR STANDARD TYPE CHIP RESISTOR ARRAY TYPE CHIP RESISTOR CONTENTS 1. STANDARD TYPE CHIP RESISTOR 1 2. ARRAY TYPE CHIP RESISTOR 4 3. THICK FILM CHIP RESISTOR
More informationChip Attenuator. Chip Attenuator
Chip Attenuator 00 Type: EXBAT (Unbalanced p type) Type: EXBAB (Balanced O type) n Features EXBAT type : Unbalanced p type l Unbalanced p type attenuator circuit in one chip(1.0 mm 1.0 mm) l Mounting occupation
More informationFrelTec GmbH. Thick Film Chip Resistor SMD Low Ohm
GmbH Mathildenstr. 10A 82319 Starnberg Germany Thick Film Chip Resistor SMD Low Ohm 9/10/2012 1/13 GmbH www.freltec.com SPECIFICATION Part Number 016 05 * 001k * J * T05 ** *** Type Size Value Tolerance
More informationPRODUCT SPECIFICATION 1 SCOPE APPLICABLE STANDARDS CATALOG NO. STRUCTURE..3 4 CONNECTOR SHAPE, DIMENSIONS AND MARTERIALS..
1 of 1 A Table of Contents: 1 SCOPE.. 3 2 APPLICABLE STANDARDS..... 3 3 CATALOG NO. STRUCTURE..3 4 CONNECTOR SHAPE, DIMENSIONS AND MARTERIALS..3 5 ACCOMMOD CONDUCTORS (CIC).....3 6 PACKAGING CONDITION........3
More informationYBR-12FRW00-C. ø12mm bi-color LED (common cathode)
Features: 1) Chip Material: AlGaInP & InGaN 2) Lens Color: Water Clear 3) Source Color: Red & White 4) Pb free 5) The product itself will remain within RoHS compliant version. Dimensions: 13.4 11.5 13.6
More informationTechnical Data Sheet 3ψ Infrared Piranha
Technical Data Sheet 3ψ Infrared Piranha Features High reliability High total radiated power Peak wavelength λp=730nm Low forward voltage Pb free The product itself will remain within RoHS compliant version.
More informationFMS series Metal Strip Shunt Lead Free Current Sensing Resistors
1. Features......2 2. Applications...... 2 3. Dimension and construction.. 2 4. Power Derating Curve....3 5. Rating.3 6. Part Number.. 3 7. Marking / Soldering..4 8. Reliability Performance..5 9. Packing.
More information*Contents in this sheet are subject to change without prior notice.
MULTILAYER CERAMIC CAPACITORS Soft Termination High Voltage Series (SH_200V to 3000V) NP0 & X7R Dielectrics 0603 to 1812 Sizes, 200V to 3000V Halogen Free & RoHS Compliance *Contents in this sheet are
More informationTo. : DATE : SPECIFICATION WRITTEN CHECKED APPROVED KORCHIP CORP.
To. : DATE : 200... SPECIFICATION PRODUCT MODEL : STARCAP : DA series WRITTEN CHECKED APPROVED KORCHIP CORP. KORCHIP B/D, 817-38, Anyang 2-dong, Manan-gu, Anyang-si, Gyeonggi-do, KOREA TEL : 82-31 - 361-8000
More information- CAUTION AND WARNING -
- CAUTION AND WARNING - Please contact us for complete technical specification before use and confirm the appropriate condition of your application. If used in a specific appliance that requires an extremely
More information3mm Photodiode PD204-6B
3mm Photodiode Features Fast response time High photo sensitivity Small junction capacitance Pb free This product itself will remain within RoHS compliant version. Description is a high speed and high
More informationShielded Power Inductors TL- 4020SG Series (4.0 x 4.0 x 2.1mm)
Shielded Power Inductors TL- 42SG Series (4. x 4. x 2.1mm) FEATURES Low DCR and excellent current handling 4. x 4. mm footprint; 2.1 mm maximum height Operating temperature range: 4 C to +125 C with Irms
More informationSMD Switch SI-C3436A General specification. Soldering conditions Reflow Soldering condition. Standard Reel Dimensions (mm) Packing specification
SMD Switch SI - C3436A - 7017 Features External Dimensions : 3.4mm x 3.6mm, Height 0.70mm Suitable for thinner and lighter portable devices Suitable for water proof devices Reflow soldering Package With
More informationProsperity Dielectrics Co., Ltd. 1 ACS-1045 Rev15
1. DESCRIPTION MLCC consists of a conducting material and electrodes. To manufacture a chip-type SMT and achieve miniaturization, high density and high efficiency, ceramic condensers are used. WTC high
More informationFIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE & HIGH OHM. RoHS COMPLIANCE ITEM Halogen and Antimony Free
Spec. No.: RHC K HTS 0001 /8 Date: 2017. 1. 10 Specification Title: FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE & HIGH OHM Style:,20 RoHS COMPLIANCE ITEM Halogen and Antimony Free Product specification
More informationERB Series. High Frequency Ceramic Capacitors. ERB Product Summary
ERB Product Summary : Exhibiting a capacitance range of 0.5 to 1,000pF, the ERB series of capacitors comes with higher Q and lower ESR which is better than the standard products of equivalent packages.
More informationPLASTIC FILM CAPACITORS
System chart Metallized polyester MDDS,MDD - For general electronic devices - For communication devices - For computer control devices - For power circuits MDDSA Metallized polypropylene MDD-P FMDD-P MMX
More informationMetallized polyester film capacitors MKT 470
MKT RADIAL POTTED TYPE PITCH 5 mm CBA141 Fig.1 Simplified outlines. FEATURES Low-inductive wound cell of metallized (PETP) film Potted with epoxy resin in a flame-retardant case Radial leads of solder-coated
More informationCHIP-TYPE EDLC Surface Mount Type Product Catalog
www.clcfactory.co.kr CHIP-TYPE EDLC Surface Mount Type Product Catalog Reflowable Super Capacitor (Chip-type EDLC) CLC Factory is a global leading power parts and materials company of the super capacitor(edlc)
More informationCommon mode ESD filter LXES**D series Document No. LX Rev1.2
Common mode ESD filter LXES**D series Document No. LX 1-1126 Rev1.2 1. This specification shall be applied to the ESD Protection Device. LXES11DAA2-135 LXES21DAA4-136 LXES11DAA2-137 LXES21DAA4-138 LXES21DAA4-14
More informationAPT1608SYCK-AMT. 1.6 x 0.8 mm SMD Chip LED Lamp DESCRIPTIONS PACKAGE DIMENSIONS FEATURES APPLICATIONS ATTENTION SELECTION GUIDE
1.6 x 0.8 mm SMD Chip LED Lamp DESCRIPTIONS The Super Bright Yellow device is made with AlGaInP (on GaAs substrate) light emitting diode chip Electrostatic discharge and power surge could damage the LEDs
More informationVariable Capacitor LXRW0YV
1. This specification shall be applied to the VARIABLE CAPACITOR. p1/17 LXRW0YV330-056 2. Features This device can carry out variable of the capacitor by adjusting the tuning voltage. This device can be
More informationPAN OVERSEAS ELECTRONIC CO., LTD.
Document No.: PRODUCT: MULTILAYER CERAMIC CAPACITOR TYPE : CHIP CAPACITOR APPROVED BY CUSTOMER ELECTRONIC CO., LTD. TAIWAN HEAD OFFICE: TEL: 02-25213252~5, 02-25634133 FAX: 02-25373069 TAIWAN FACTORY:
More informationAA2214VRBXS/A-TR-AMT 2.2 x 1.4 mm Surface Mount LED Lamp
2.2 x 1.4 mm Surface Mount LED Lamp DESCRIPTIONS The source color devices are made with InGaN Light Emitting Diode Electrostatic discharge and power surge could damage the LEDs It is recommended to use
More information100 pf to 47µF RoHS compliant & Halogen free
Product Specification August 7, 2017 V.4 DATA SHEET SURFACE MOUNT MULTILAYER CERAMIC CAPACITORS General purpose class II X6S 4 V TO 50 V 0 pf to 47µF RoHS compliant & Halogen free 2 SCOPE This specification
More informationDATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS General purpose & High capacitance Class 2, X5R
DATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS General purpose & High capacitance Class 2, 6.3 V TO 50 V 10 nf to 100 µf RoHS compliant Product Specification Product specification 2 Surface-Mount
More informationThick Film Chip Resistors (CR, CJ Series)
Thick Film hip Resistors (R, J Series) Structure and material D E Features Low Noise Nickel arrier Terminations pplication General Purpose ode Structure Material oating Glass or Epoxy Resistor RuO2 Resistor
More informationConductive Polymer Capacitors
CONDUCTIVE POLYMER CHARACTERISTICS Conductive Polymer Capacitors ITEM CONDITIONS SPECIFICATION Rotational temperature test High-temperature endurance life test Capacitors are placed in an oven with a specific
More informationSolid Tantalum Chip Capacitors TANTAMOUNT, Low Profile, Conformal Coated, Maximum CV
Solid Tantalum Chip Capacitors TANTAMOUNT, Low Profile, Conformal Coated, Maximum CV FEATURES New case size offerings. 2mm height Terminations: Tin (2) standard. Low ESR 8mm, 12mm tape and reel packaging
More informationCHIP RESISTOR. Chip Resistors Selection Guide. General Purpose Chip Resistor. Zero Ohm Jumper Resistor. Chip Resistor Array MAX WORKING VOLTAGE
Chip Resistors Selection Guide General Purpose Chip Resistor SIZE/ mm POWER RATING MAX WORKING VOLTAGE TOLERANCE RESISTANCE RANGE 0402 1.00*0.50 0603 1.60*0.80 1/10W 0. 0805 2.00*1.25 1/8W 1 0. 1206 3.10*1.60
More information5484BN/R7DC-AHJB/XR/MS(ELA)
Features High luminous intensity output Oval Shape Well defined spatial radiation Wide viewing angle (2θ 1/2 ) : 110 / 40 UV resistant epoxy The product itself will remain within RoHS compliant version
More informationDATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS General purpose & High capacitance Class 2, X5R
DATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS General purpose & High capacitance Class 2, 6.3 V TO 50 V 10 nf to 100 µf RoHS compliant Product Specification Product specification 2 Surface-Mount
More informationPRODUCT SPECIFICATION
Page 1 Page 2 1.0 SCOPE. This specification covers performance, tests and quality requirements for the SIM Card Connector SIM 2055 (Receiver Type, 6-Pin, SMT, 1.8 & 2.2mm Profiles). 2.0 PRODUCT NAME AND
More informationTechnical Data Sheet Mini Top View LEDs
Features White SMT package. Optical indicator. Wide viewing angle. Soldering methods: IR reflow soldering Available on tape and reel Pb-free The product itself will remain within RoHS compliant version.
More information3mm Advanced Super Flux LEDs B84-YSC-A1T1U1DH-AM
3mm Advanced Super Flux LEDs Feature RoHS compliant. Piranha package. Colorless clear resin. Low thermal resistance Packaged in tubes for automatic insertion equipment. Total flux: 7150 to 14250 mlm at
More information(1) SHAPES AND DIMENSIONS
Ⅰ. SCOPE: This specification applies to the Pb Free high current type SMD Common mode filter for MCM-2M-SERIES PRODUCT INDENTIFICATION MCM - 2M - 70 2 3 Product Code 2 Dimensions Code 3 Impedance Code
More information5mm Phototransistor PT333-3B
Features Fast response time High photo sensitivity Pb free The product itself will remain within RoHS compliant version. Description is a high speed and high sensitive NPN silicon NPN epitaxial planar
More informationChip tantalum capacitors
Chip tantalum capacitors TCO Series Features ( ) 1) Conductive polymer used for the cathode material. 2) Ultra-low ESR. (1/ compared with the conventional type) 3) Screening by thermal shock. External
More informationSuper High AUTO (SHA) Series
PART NO. SFI1206SA240-1R5J 1.1 Technology Data Symbol Value Unit Maximum allowable continuous DC voltage V DC 12 V Breakdown voltage measured Vv 24(±10%) V Maximum clamping voltage V CLAMP < 40 V Maximum
More informationDATA SHEET General Purpose Thick Film Chip Resistor CR Series
Towards Excellence in Quality, Service & Innovation DATA SHEET General Purpose Thick Film Chip Resistor 1% TO 5%, TCR -200 TO +600 SIZE: 01005/0201/0402/0603/0805/1206/1210/2010/2512 RoHs Compliant Jan
More informationCONTENT (MLCC) E STANDARD NUMBER... 3 STRUCTURE... 4 ORDERING CODE... 4 GENERAL PURPOSE FOR SMARTPHONE... 5
MLCC MLCC CONTENT (MLCC) E STANDARD NUMBER... 3 STRUCTURE... 4 ORDERING CODE... 4 GENERAL PURPOSE FOR SMARTPHONE... 5 CLASS II: HIGH DIELECTRIC CONSTANT TYPE... 6 X5R Series... 6 TEST SPEC.... 7 PACKAGE...
More information/ NTSSeries NTFSeries Temperature cycle : 1000 cycles
/ NTSSeries NTFSeries Temperature cycle : 00 cycles FEATURES 1. Large capacitance by small size. 2. Excellent noise absorption. 3. High permissible ripple current capability. 4. NTF: Temperature cycle
More informationRing encoder with 4mm height contribute to space saving and multifunctioning. Typical Specifications. Rating. Operating life
E E mm Size encoder with mm height contribute to space saving and multifunctioning Typical Specifications Items Specifications Product Line Structure Dip ctuator l e n g t h(m m) Reflow Detent torque (mn
More informationTo Non-Controlled Copy
SPECIFICATION SPEC. No. C-Open-a D A T E : 2013 Sep. To Non-Controlled Copy CUSTOMER S PRODUCT NAME TDK PRODUCT NAME Upon the acceptance of this spec. previous spec. (C2004-816-031) shall be abolished.
More informationALUMINUM ELECTROLYTIC CAPACITORS REFERENCE SHEET
TO Messrs. AVNET ABACUS ALUMINUM ELECTROLYTIC CAPACITORS REFERENCE SHEET CUSTOMER PART No. Rubycon PART No. 35 TLV 470 M 12.5X13.5 DRAWING No. RERS 011758 ISSUE No. 1 ISSUE DATE 25 AUGUST 2010 ENGINEERING
More informationMetal Oxide Varistor:TVM-G Series
Features 1. RoHS compliant 2. Low clamping voltage 3. EIA size 0402, 0603, 0805 4. Working voltage: 5.5 ~ 30 Vdc 5. Bidirectional and symmetrical V/I characteristics 6. Multilayer ceramic construction
More informationEAPL4040WA1. SMD Side View LEDs PRELIMINARY. Features. Applications.
SMD Side View LEDs PRELIMINARY Features Fluorescence Type High Luminous Intensity High Efficiency Pb-free. The product itself will remain within RoHS compliant version. ESD protection. Applications OA
More information50 TZV 1500 M JDE VB 18X21.5
EXTENDED BASE FEATURES: VB- VIBRATION BASE AEC-Q200 SURFACE MOUNT ROHS COMPLIANT APPLICATIONS: AUTOMOTIVE POWER INDUSTRIAL SPEC: VALUE: MPN :50 TZV 1500 M JDE VB 18X21.5 VDC 50 CAPACITANCE 1500μF +/- 20%
More informationLAMP UTW/S400-X9/T10(WS)
Features Popular 5mm package High luminous power Typical chromaticity coordinates x=0.24, y=0.20 according to CIE1931 Bulk, available taped on reel. ESD-withstand voltage: up to 150V The product itself
More information