STEVAL-ILL0V Smart home lighting based on HVLEDPF and SPSGRF Data brief Description The STEVAL-ILL0V evaluation board is an offline LED driver based on the HVLEDPF, coupled with Sub-GHz connectivity based on the SPSGRF- low power programmable RF transceiver module. The interface between the HVLEDPF and the SPSGRF is managed by an STML0 ultra-low-power ARM Cortex -M0+ MCU. The microcontroller and connectivity module are supplied by the LED driver through an auxiliary winding. The LED driver evaluation board can operate in standalone mode in communication with the bundled STEVAL-ILL0V_Remote controller based on SPML to help to reduce development and certification time. The board can also be rendered visible to cloud applications with the addition of a wireless bridge. Features LED driver features: 0 W flyback converter with quasiresonant operation Primary side regulation, no optocoupler required High power factor and low THD Open circuit and short-circuit LED management ±% LED current regulation Dimming range:.% to 00% Sub-GHz connectivity features: Works with the bundled STEVAL- ILL0V_remote controller based on SPML- sub-ghz module Allows remote lamp powering on and off Allows lamp remote dimming Standby power consumption: < 0. W RoHS compliant October 0 DocID000 Rev / For further information contact your local STMicroelectronics sales office www.st.com
J HEADER.0 mm Pitch Fusable resisitor/0e R F A RV PB_LED_DIMM R9 K - + R 00K HD0-T D C nf/x Q L R mh.k C 00nF/X L mh.k R BSS R.K R 0K R 0K R 0K R C AC-DC Converter Circui t C 0nF U 00pF R 0K C.uF PA0_LED_OFF HVLEDPF C.nF D STTHL0 C9 00nF D BAT R 0K R.0R R.K C0 00uF D N DMG Q R.99K MMBT90 R0 K C N D MCU Supply 0uF R K T EF0 C nf/y D STTHL0 C 0uF Lp = 9µH, Np =, Ns=, Naux = TP C 0uF TP R K TP R0 Mounting Holes J HEADER.0 mm Pitch STEVAL-ILL0V Figure : STEVAL-ILL0V circuit schematic ( of ) DMG N.A COMP DMG ILED NC 9 NC 0 NC NC DRAIN VCC DRAIN CS DRAIN SOURCE DRAIN / DocID000 Rev
STEVAL-ILL0V Figure : STEVAL-ILL0V circuit schematic ( of ) V R 0K SW PB_SDN_RADIO PB_LED_DIMM C 00nF PUSHBUTTON C 00nF V C 00nF V PA0_GPIO_0_RADIO PA_GPIO RADIO PA_GPIO RADIO _PA D PB BOOT0 PB 0 PB 9 PB PB PB PA U VDD_ PC_OSC_IN PC_OSC_OUT VDDA STML0x PA0 PA PA PA PA PA PA 0 PA0 9 PA9 PA VDD PA_SWCLK PA_SWDIO PA0_LED_OFF V PA PA PA PA PA PB0 PB PB C9 00nF 9 0 PA_GPIO RADIO PA_SPI_SCK_RADIO PA_SPI_MISO_RADIO PA_SPI_MOSI_RADIO PB_SPI_CS_RADIO Microcontroller Unit R9 K U R 0K J C 0uF C V MCU Supply C VOUT VIN LDL VADJ EN PA_SWDIO PA_SWCLK 0 9 V 00nF uf HEADER X MCU Power Supply Programming Connector PA_GPIO RADIO PA_GPIO RADIO PA_GPIO RADIO PA0_GPIO_0_RADIO V C0 0uF U GPIO_ SDN GPIO_ SPI_CS 0 GPIO_ SPI_MOSI 9 GPIO_0 SPI_MISO Vin SPI_CLK SPSGRF PB_SDN_RADIO PB_SPI_CS_RADIO PA_SPI_MOSI_RADIO PA_SPI_MISO_RADIO PA_SPI_SCK_RADIO BLE/SPIRIT Transceiver Unit DocID000 Rev /
SPMOD_IC_SDA DRDY SDA/SDI/SDO INT INT Vdd_IO Res Res Res Figure : STEVAL-ILL0V_Remote circuit schematic STEVAL-ILL0V C 0µF V C 00nF R 0K C 00pF SPMOD_TXRXLED SPMOD_SHDN SPMOD_LED_USER SPMOD_INT V SPMOD_LED_USER U TXRXLED SHDN GPIO0 GPIO MODE0 MODE VDD SPML MHz CTS RTS RXD TXD RESET BOOTMODE SWCLK 0 SWDIO 9 SPMOD_IC_SDA SPMOD_IC_SCL R 0K SPMOD_SW SPMOD_SW R 0K R 0K SPMOD_SWCLK SPMOD_SWDIO D SPMOD_SHDN V SPMOD_TXRXLED J SW BATJ SPMOD_SW BT BATTERY JUMPER R 0K C9 00nF V R 0K SPMOD_LED_USER SPMOD_LED_USER R9 0E R 0E D D LED LED SW R 0K D BATJ C 00nF SPMOD_SHDN SPMOD_SW V R 0K SPMOD_SW SPMOD_SW D ESDALCV-U D ESDALCV-U SW RESET C0 00nF V R R V SPMOD_IC_SCL SPMOD_IC_SDA R R SCL/SPC SDA/SDI/SDO SDO/SA0 CS 0 9 Vdd V C U R0 R U C V VDD SPMOD_IC_SCL SCL/SPC CS SPMOD_INT V R 0K R 0K V SPMOD_SWDIO SPMOD_SWCLK J CON / DocID000 Rev
STEVAL-ILL0V Revision history Revision history Table : Document revision history Date Version Changes 0-Feb-0 Initial release. -Oct-0 Updated cover page Features and Description DocID000 Rev /
STEVAL-ILL0V IMPORTANT NOTICE PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries ( ST ) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. 0 STMicroelectronics All rights reserved / DocID000 Rev