L78LxxAB L78LxxAC - L78LxxC
|
|
|
- Benedict Baldwin
- 5 years ago
- Views:
Transcription
1 L78LxxAB L78LxxAC - L78LxxC Positive voltage regulators Features Output current up to 100 s of 3.3; 5; 6; 8; 9; 10; 12; 15; 18; 24 Thermal overload protection Short circuit protection No external components are required Available in either ± 5% (AC) or ± 10% (C) selection TO-92 Description SO-8 SOT-89 The L78Lxx series of three-terminal positive regulators employ internal current limiting and thermal shutdown, making them essentially indestructible. If adequate heat-sink is provided, they can deliver up to 100 output current. They are intended as fixed voltage regulators in a wide range of applications including local or oncard regulation for elimination of noise and distribution problems associated with single-point regulation. In addition, they can be used with power pass elements to make high-current voltage regulators. The L78Lxx series used as Zener diode/resistor combination replacement, offers an effective output impedance improvement of typically two orders of magnitude, along with lower quiescent current and lower noise. Table 1. Device summary Part numbers L78L33C L78L08AC L78L15C L78L33AC L78L08AB L78L15AC L78L33AB L78L09C L78L15AB L78L05C L78L09AC L78L18C L78L05AC L78L09AB L78L18AC L78L05AB L78L10AC L78L24C L78L06AC L78L12C L78L24AC L78L06AB L78L12AC L78L24AB L78L08C L78L12AB April 2009 Doc ID 2145 Rev 17 1/
2 Contents L78LxxAB - L78LxxAC - L78LxxC Contents 1 Diagram Pin configuration Maximum ratings Electrical characteristics Typical performance Typical application Package mechanical data Order codes Revision history /29 Doc ID 2145 Rev 17
3 L78LxxAB - L78LxxAC - L78LxxC Diagram 1 Diagram Figure 1. Schematic diagram Doc ID 2145 Rev 17 3/29
4 Pin configuration L78LxxAB - L78LxxAC - L78LxxC 2 Pin configuration Figure 2. Pin connection (top view, bottom view for TO-92) SO-8 SOT-89 PIN 1 = OUT PIN 2 = GND PIN 3 = IN TO-92 Figure 3. Test circuits 4/29 Doc ID 2145 Rev 17
5 L78LxxAB - L78LxxAC - L78LxxC Maximum ratings 3 Maximum ratings Table 2. Absolute maximum ratings Symbol Parameter alue Unit O = 3.3 to 9 30 I DC Input voltage O = 12 to O = 18 to I O Output current 100 P D Power dissipation Internally limited (1) mw T STG Storage temperature range -65 to 150 C T OP Operating junction temperature range for L78L00AC 0 to 150 C for L78L00AB -40 to Our SO-8 package used for voltage regulators is modified internally to have pins 2, 3, 6 and 7 electrically communed to the die attach flag. This particular frame decreases the total thermal resistance of the package and increases its ability to dissipate power when an appropriate area of copper on the printed circuit board is available for heat-sinking. The external dimensions are the same as for the standard SO-8. Table 3. Thermal data Symbol Parameter SO-8 TO-92 SOT-89 Unit R thjc Thermal resistance junction-case. (max) C/W R thja Thermal resistance junction-ambient. (max) 55 (1) (1) C/W 1. Considering 6 cm 2 of copper Board heat-sink. Doc ID 2145 Rev 17 5/29
6 Electrical characteristics L78LxxAB - L78LxxAC - L78LxxC 4 Electrical characteristics Refer to the test circuits, T J = 0 to 125 C, I O = 40, C I = 0.33 µf, C O = 0.1 µf unless otherwise specified. Table 4. Electrical characteristics of L78L33C ( I = 8.3 ) O T J = 25 C O Δ change I O = 1 to 40, I = 5.3 to I O = 1 to 70, I = I = 5.3 to 20, T J = 25 C 150 I = 6.3 to 20, T J = 25 C 100 I O = 1 to 100, T J = 25 C 60 I O = 1 to 40, T J = 25 C 30 T J = 25 C 6 T J = 125 C 5.5 I O = 1 to I = 6.3 to en Output noise voltage B =10 Hz to 100 khz, T J = 25 C 40 µ SR Supply voltage rejection I = 6.3 to 16.3, f = 120 Hz I O = 40, T J = 25 C db d Dropout voltage 1.7 6/29 Doc ID 2145 Rev 17
7 L78LxxAB - L78LxxAC - L78LxxC Electrical characteristics Table 5. Electrical characteristics of L78L05C ( I = 10 ) O T J = 25 C O Δ change I O = 1 to 40, I = 7 to I O = 1 to 70, I = I = 8.5 to 20, T J = 25 C 200 I = 9 to 20, T J = 25 C 150 I O = 1 to 100, T J = 25 C 60 I O = 1 to 40, T J = 25 C 30 T J = 25 C 6 T J = 125 C 5.5 I O = 1 to I = 8 to en Output noise voltage B =10 Hz to 100 khz, T J = 25 C 40 µ SR Supply voltage rejection I = 9 to 20, f = 120 Hz I O = 40, T J = 25 C db d Dropout voltage 1.7 Table 6. Electrical characteristics of L78L08C ( I = 14 ) O T J = 25 C O Δ change I O = 1 to 40, I = 8.5 to I O = 1 to 70, I = I = 8.5 to 20, T J = 25 C 200 I = 9 to 20, T J = 25 C 150 I O = 1 to 100, T J = 25 C 80 I O = 1 to 40, T J = 25 C 40 T J = 25 C 6 T J = 125 C 5.5 I O = 1 to I = 8 to en Output noise voltage B =10 Hz to 100 khz, T J = 25 C 60 µ SR Supply voltage rejection I = 9 to 20, f = 120 Hz I O = 40, T J = 25 C db d Dropout voltage 1.7 Doc ID 2145 Rev 17 7/29
8 Electrical characteristics L78LxxAB - L78LxxAC - L78LxxC Table 7. Electrical characteristics of L78L09C ( I = 15 ) O T J = 25 C O Δ change I O = 1 to 40, I = 11.5 to I O = 1 to 70, I = I = 11.5 to 23, T J = 25 C 250 I = 12 to 23, T J = 25 C 200 I O = 1 to 100, T J = 25 C 80 I O = 1 to 40, T J = 25 C 40 T J = 25 C 6 T J = 125 C 5.5 I O = 1 to I = 12 to en Output noise voltage B =10 Hz to 100 khz, T J = 25 C 70 µ SR Supply voltage rejection I = 12 to 23, f = 120 Hz I O = 40, T J = 25 C db d Dropout voltage 1.7 Table 8. Electrical characteristics of L78L10C ( I = 16 ) O T J = 25 C O Δ change I O = 1 to 40, I = 12.5 to I O = 1 to 70, I = I = 12.5 to 23, T J = 25 C 230 I = 13 to 23, T J = 25 C 170 I O = 1 to 100, T J = 25 C 80 I O = 1 to 40, T J = 25 C 40 T J = 25 C 6 T J = 125 C 5.5 I O = 1 to I = 13 to en Output noise voltage B =10Hz to 100kHz, T J = 25 C 60 µ SR Supply voltage rejection I = 14 to 23, f = 120Hz I O = 40, T J = 25 C db d Dropout voltage 1.7 8/29 Doc ID 2145 Rev 17
9 L78LxxAB - L78LxxAC - L78LxxC Electrical characteristics Table 9. Electrical characteristics of L78L12C ( I = 19 ) O T J = 25 C O Δ change I O = 1 to 40, I = 14.5 to I O = 1 to 70, I = I = 14.5 to 27, T J = 25 C 250 I = 16 to 27, T J = 25 C 200 I O = 1 to 100, T J = 25 C 100 I O = 1 to 40, T J = 25 C 50 T J = 25 C 6.5 T J = 125 C 6 I O = 1 to I = 16 to en Output noise voltage B =10 Hz to 100 khz, T J = 25 C 80 µ SR Supply voltage rejection I = 15 to 25, f = 120 Hz I O = 40, T J = 25 C db d Dropout voltage 1.7 Table 10. Electrical characteristics of L78L15C ( I = 23 ) O T J = 25 C O Δ change I O = 1 to 40, I = 17.5 to I O = 1 to 70, I = I = 17.5 to 30, T J = 25 C 300 I = 20 to 30, T J = 25 C 250 I O = 1 to 100, T J = 25 C 150 I O = 1 to 40, T J = 25 C 75 T J = 25 C 6.5 T J = 125 C 6 I O = 1 to I = 20 to en Output noise voltage B =10 Hz to 100 khz, T J = 25 C 90 µ SR Supply voltage rejection I = 18.5 to 28.5, f = 120 Hz I O = 40, T J = 25 C db d Dropout voltage 1.7 Doc ID 2145 Rev 17 9/29
10 Electrical characteristics L78LxxAB - L78LxxAC - L78LxxC Table 11. Electrical characteristics of L78L18C ( I = 27 ) O T J = 25 C O Δ change I O = 1 to 40, I = 22 to I O = 1 to 70, I = I = 22 to 33, T J = 25 C 320 I = 22 to 33, T J = 25 C 270 I O = 1 to 100, T J = 25 C 170 I O = 1 to 40, T J = 25 C 85 T J = 25 C 6.5 T J = 125 C 6 I O = 1 to I = 23 to en Output noise voltage B =10 Hz to 100 khz, T J = 25 C 120 µ SR Supply voltage rejection I = 23 to 33, f = 120 Hz I O = 40, T J = 25 C db d Dropout voltage 1.7 Table 12. Electrical characteristics of L78L24C ( I = 33 ) O T J = 25 C O Δ change I O = 1 to 40, I = 27 to I O = 1 to 70, I = I = 27 to 38, T J = 25 C 350 I = 28 to 38, T J = 25 C 300 I O = 1 to 100, T J = 25 C 200 I O = 1 to 40, T J = 25 C 100 T J = 25 C 6.5 T J = 125 C 6 I O = 1 to I = 28 to en Output noise voltage B =10 Hz to 100 khz, T J = 25 C 200 µ SR Supply voltage rejection I = 29 to 35, f = 120 Hz I O = 40, T J = 25 C db d Dropout voltage /29 Doc ID 2145 Rev 17
11 L78LxxAB - L78LxxAC - L78LxxC Electrical characteristics T J = 0 to 125 C for L78L33AC, T J = -40 to 125 C for L78L33AB. Table 13. Electrical characteristics of L78L33AB and L78L33AC ( I = 8.3 ) O T J = 25 C O Δ change I O = 1 to 40, I = 5.3 to I O = 1 to 70, I = I = 5.3 to 20, T J = 25 C 150 I = 6.3 to 20, T J = 25 C 100 I O = 1 to 100, T J = 25 C 60 I O = 1 to 40, T J = 25 C 30 T J = 25 C 6 T J = 125 C 5.5 I O = 1 to I = 6.3 to en Output noise voltage B =10 Hz to 100 khz, T J = 25 C 40 µ SR Supply voltage rejection I = 6.3 to 16.3, f = 120 Hz I O = 40, T J = 25 C db d Dropout voltage 1.7 T J = 0 to 125 C for L78L05AC, T J = -40 to 125 C for L78L05AB. Table 14. Electrical characteristics of L78L05AB and L78L05AC ( I = 10 ) O T J = 25 C O Δ change I O = 1 to 40, I = 7 to I O = 1 to 70, I = I = 7 to 20, T J = 25 C 150 I = 8 to 20, T J = 25 C 100 I O = 1 to 100, T J = 25 C 60 I O = 1 to 40, T J = 25 C 30 T J = 25 C 6 T J = 125 C 5.5 I O = 1 to I = 8 to en Output noise voltage B =10 Hz to 100 khz, T J = 25 C 40 µ SR Supply voltage rejection I = 8 to 18, f = 120 Hz I O = 40, T J = 25 C db d Dropout voltage 1.7 Doc ID 2145 Rev 17 11/29
12 Electrical characteristics L78LxxAB - L78LxxAC - L78LxxC T J = 0 to 125 C for L78L06AC, T J = -40 to 125 C for L78L06AB. Table 15. Electrical characteristics of L78L06AB and L78L06AC ( I = 12 ) O T J = 25 C O Δ change I O = 1 to 40, I = 8.5 to I O = 1 to 70, I = I = 8.5 to 20, T J = 25 C 150 I = 9 to 20, T J = 25 C 100 I O = 1 to 100, T J = 25 C 60 I O = 1 to 40, T J = 25 C 30 T J = 25 C 6 T J = 125 C 5.5 I O = 1 to I = 9 to en Output noise voltage B =10 Hz to 100 khz, T J = 25 C 50 µ SR Supply voltage rejection I = 9 to 20, f = 120 Hz I O = 40, T J = 25 C db d Dropout voltage 1.7 T J = 0 to 125 C for L78L08AC, T J = -40 to 125 C for L78L08AB. Table 16. Electrical characteristics of L78L08AB and L78L08AC ( I = 14 ) O T J = 25 C O Δ change I O = 1 to 40, I = 10.5 to I O = 1 to 70, I = I = 10.5 to 23, T J = 25 C 175 I = 11 to 23, T J = 25 C 125 I O = 1 to 100, T J = 25 C 80 I O = 1 to 40, T J = 25 C 40 T J = 25 C 6 T J = 125 C 5.5 I O = 1 to I = 11 to en Output noise voltage B =10 Hz to 100 khz, T J = 25 C 60 µ SR Supply voltage rejection I = 12 to 23, f = 120 Hz I O = 40, T J = 25 C db d Dropout voltage /29 Doc ID 2145 Rev 17
13 L78LxxAB - L78LxxAC - L78LxxC Electrical characteristics T J = 0 to 125 C for L78L09AC, T J = -40 to 125 C for L78L09AB. Table 17. Electrical characteristics of L78L09AB and L78L09AC ( I = 15 ) O T J = 25 C O Δ change I O = 1 to 40, I = 11.5 to I O = 1 to 70, I = I = 11.5 to 23, T J = 25 C 225 I = 12 to 23, T J = 25 C 150 I O = 1 to 100, T J = 25 C 80 I O = 1 to 40, T J = 25 C 40 T J = 25 C 6 T J = 125 C 5.5 I O = 1 to I = 12 to en Output noise voltage B =10 Hz to 100 khz, T J = 25 C 70 µ SR Supply voltage rejection I = 12 to 23, f = 120 Hz I O = 40, T J = 25 C db d Dropout voltage 1.7 T J = 0 to 125 C for L78L10AC, T J = -40 to 125 C for L78L10AB. Table 18. Electrical characteristics of L78L10AC ( I = 16 ) O T J = 25 C O Δ change I O = 1 to 40, I = 12.5 to I O = 1 to 70, I = I = 12.5 to 23, T J = 25 C 230 I = 13 to 23, T J = 25 C 170 I O = 1 to 100, T J = 25 C 80 I O = 1 to 40, T J = 25 C 40 T J = 25 C 6 T J = 125 C 5.5 I O = 1 to I = 13 to en Output noise voltage B =10 Hz to 100 khz, T J = 25 C 60 µ SR Supply voltage rejection I = 14 to 23, f = 120 Hz I O = 40, T J = 25 C db d Dropout voltage 1.7 Doc ID 2145 Rev 17 13/29
14 Electrical characteristics L78LxxAB - L78LxxAC - L78LxxC T J = 0 to 125 C for L78L12AC, T J = -40 to 125 C for L78L12AB. Table 19. Electrical characteristics of L78L12AB and L78L12AC ( I = 19 ) O T J = 25 C O Δ change I O = 1 to 40, I = 14.5 to I O = 1 to 70, I = I = 14.5 to 27, T J = 25 C 250 I = 16 to 27, T J = 25 C 200 I O = 1 to 100, T J = 25 C 100 I O = 1 to 40, T J = 25 C 50 T J = 25 C 6.5 T J = 125 C 6 I O = 1 to I = 16 to en Output noise voltage B =10 Hz to 100 khz, T J = 25 C 80 µ SR Supply voltage rejection I = 15 to 25, f = 120 Hz I O = 40, T J = 25 C db d Dropout voltage 1.7 T J = 0 to 125 C for L78L15AC, T J = -40 to 125 C for L78L15AB. Table 20. Electrical characteristics of L78L15AB and L78L15AC ( I = 23 ) O T J = 25 C O Δ change I O = 1 to 40, I = 17.5 to I O = 1 to 70, I = I = 17.5 to 30, T J = 25 C 300 I = 20 to 30, T J = 25 C 250 I O = 1 to 100, T J = 25 C 150 I O = 1 to 40, T J = 25 C 75 T J = 25 C 6.5 T J = 125 C 6 I O = 1 to I = 20 to en Output noise voltage B =10 Hz to 100 khz, T J = 25 C 90 µ SR Supply voltage rejection I = 18.5 to 28.5, f = 120 Hz I O = 40, T J = 25 C db d Dropout voltage /29 Doc ID 2145 Rev 17
15 L78LxxAB - L78LxxAC - L78LxxC Electrical characteristics T J = 0 to 125 C for L78L18AC, T J = -40 to 125 C for L78L18AB. Table 21. Electrical characteristics of L78L18AC ( I = 27 ) O T J = 25 C O Δ change I O = 1 to 40, I = 22 to I O = 1 to 70, I = I = 22 to 33, T J = 25 C 320 I = 22 to 33, T J = 25 C 270 I O = 1 to 100, T J = 25 C 170 I O = 1 to 40, T J = 25 C 85 T J = 25 C 6.5 T J = 125 C 6 I O = 1 to I = 23 to en Output noise voltage B =10 Hz to 100 khz, T J = 25 C 120 µ SR Supply voltage rejection I = 23 to 33, f = 120 Hz I O = 40, T J = 25 C db d Dropout voltage 1.7 T J = 0 to 125 C for L78L24AC, T J = -40 to 125 C for L78L24AB. Table 22. Electrical characteristics of L78L24AB and L78L24AC ( I = 33 ) O T J = 25 C O Δ change I O = 1 to 40, I = 27 to I O = 1 to 70, I = I = 27 to 38, T J = 25 C 350 I = 28 to 38, T J = 25 C 300 I O = 1 to 100, T J = 25 C 200 I O = 1 to 40, T J = 25 C 100 T J = 25 C 6.5 T J = 125 C 6 I O = 1 to I = 28 to en Output noise voltage B =10 Hz to 100 khz, T J = 25 C 200 µ SR Supply voltage rejection I = 29 to 33, f = 120 Hz I O = 40, T J = 25 C db d Dropout voltage 1.7 Doc ID 2145 Rev 17 15/29
16 Typical performance L78LxxAB - L78LxxAC - L78LxxC 5 Typical performance Figure 4. L78L05/12 output voltage vs. ambient temperature Figure 5. L78L05/12/24 load characteristics Figure 6. L78L05/12/24 thermal shutdown Figure 7. L78L05/12 quiescent current vs. output current Figure 8. L78L05 quiescent current vs. input voltage Figure 9. L78L05/12/24 output characteristics 16/29 Doc ID 2145 Rev 17
17 L78LxxAB - L78LxxAC - L78LxxC Typical performance Figure 10. L78L05/12/24 ripple rejection Figure 11. L78L05 dropout characteristics Figure 12. L78Lxx short circuit output current Doc ID 2145 Rev 17 17/29
18 Typical application L78LxxAB - L78LxxAC - L78LxxC 6 Typical application Figure 13. High output current short circuit protected Figure 14. Edit boost circuit Figure 15. Current regulator 18/29 Doc ID 2145 Rev 17
19 L78LxxAB - L78LxxAC - L78LxxC Typical application Figure 16. Adjustable output regulator Doc ID 2145 Rev 17 19/29
20 Package mechanical data L78LxxAB - L78LxxAC - L78LxxC 7 Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: ECOPACK is an ST trademark. 20/29 Doc ID 2145 Rev 17
21 L78LxxAB - L78LxxAC - L78LxxC Package mechanical data SO-8 mechanical data Dim. mm. inch. Min. Typ. Max. Min. Typ. Max. A A A B C D E e H h L k 8 (max.) ddd /C Doc ID 2145 Rev 17 21/29
22 Package mechanical data L78LxxAB - L78LxxAC - L78LxxC SOT-89 mechanical data Dim. mm. mils. Min. Typ. Max. Min. Typ. Max. A B B C C D D E e e H L P025H 22/29 Doc ID 2145 Rev 17
23 L78LxxAB - L78LxxAC - L78LxxC Package mechanical data TO-92 mechanical data Dim. mm. mils. Min. Typ. Max. Min. Typ. Max. A b D E e e L R S W α /D Doc ID 2145 Rev 17 23/29
24 Package mechanical data L78LxxAB - L78LxxAC - L78LxxC Tape & reel SO-8 mechanical data Dim. mm. inch. Min. Typ. Max. Min. Typ. Max. A C D N T Ao Bo Ko Po P /29 Doc ID 2145 Rev 17
25 L78LxxAB - L78LxxAC - L78LxxC Package mechanical data Tape & reel SOT-89 mechanical data Dim. mm. inch. Min. Typ. Max. Min. Typ. Max. A C D N T Ao Bo Ko Po P Doc ID 2145 Rev 17 25/29
26 Package mechanical data L78LxxAB - L78LxxAC - L78LxxC Tape & reel for TO-92 mechanical data Dim. mm. inch. Min. Typ. Max. Min. Typ. Max. A T T T d P P F1, F delta H ± W W W W H H H D t L delta P ± u Φ Φ delta P A1 T2 T T1 H1 delta H H H0 L d W2 l1 W0 W1 W F1 P2 F2 P0 D0 t DRAWING NOT IN SCALE 26/29 Doc ID 2145 Rev 17
27 L78LxxAB - L78LxxAC - L78LxxC Order codes 8 Order codes Table 23. Order codes Packages Part numbers SO-8 TO92 (BAG) (1) SOT-89 s L78L33C L78L33CD-TR 3.3 L78L33AC L78L33ACD13TR L78L33ACZ L78L33ACUTR 3.3 L78L33AB L78L33ABD-TR L78L33ABZ L78L33ABUTR 3.3 L78L05C L78L05CD13TR L78L05CZ 5 L78L05AC L78L05ACD13TR L78L05ACZ L78L05ACUTR 5 L78L05AB L78L05ABD13TR L78L05ABZ L78L05ABUTR 5 L78L06AC L78L06ACD13TR L78L06ACZ L78L06ACUTR 6 L78L06AB L78L06ABD13TR L78L06ABZ L78L06ABUTR 6 L78L08C L78L08CD13TR 8 L78L08AC L78L08ACD13TR L78L08ACZ L78L08ACUTR 8 L78L08AB L78L08ABD13TR L78L08ABZ L78L08ABUTR 8 L78L09C L78L09CD13TR 9 L78L09AC L78L09ACD13TR L78L09ACZ L78L09ACUTR 9 L78L09AB L78L09ABD13TR L78L09ABZ L78L09ABUTR 9 L78L10AC L78L10ACUTR 10 L78L12C L78L12CD13TR 12 L78L12AC L78L12ACD13TR L78L12ACZ L78L12ACUTR 12 L78L12AB L78L12ABD-TR L78L12ABZ L78L12ABUTR 12 L78L15C L78L15CD-TR 15 L78L15AC L78L15ACD13TR L78L15ACZ L78L15ACUTR 15 L78L15AB L78L15ABZ L78L15ABUTR 15 L78L18C L78L18CD13TR 18 L78L18AC L78L18ACD13TR L78L18ACUTR 18 L78L24C L78L24CD-TR 24 L78L24AC L78L24ACD-TR L78L24ACZ L78L24ACUTR 24 L78L24AB L78L24ABD13TR L78L24ABZ Available in Ammopak with the suffix "-AP" or in tape and reel with the suffix "TR". Please note that in these cases pins are shaped according to tape and reel specifications. Doc ID 2145 Rev 17 27/29
28 Revision history L78LxxAB - L78LxxAC - L78LxxC 9 Revision history Table 24. Document revision history Date Revision Changes 14-Mar Add tape and reel for TO Mar Add note on Table Dec Mistake on ordering Table in header. 12-Sep Order codes updated. 07-Jun Order codes updated. 18-Sep Added Table 1 in cover page. 15-Jul Modified: Table 1 on page 1 and Table 23 on page Aug Modified Figure 12 on page Apr Added: R thja value for SOT-89 Table 3 on page 5. 28/29 Doc ID 2145 Rev 17
29 L78LxxAB - L78LxxAC - L78LxxC Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics N and its subsidiaries ( ST ) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROED IN WRITING BY AN AUTHORIZED ST REPRESENTATIE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEERE PROPERTY OR ENIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIE GRADE" MAY ONLY BE USED IN AUTOMOTIE APPLICATIONS AT USER S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America Doc ID 2145 Rev 17 29/29
79L05-SMD. Negative voltage regulators. Features. Description 79L05 SMD (SO-8)
79L05-SMD 79L05 SMD (SO-8) Negative voltage regulators Features Output current up to 100 s of -5; -6; -8; -9; -12; -15 Thermal overload protection Short circuit protection No external components are required
Order codes Part numbers DPAK (tape and reel) PPAK (tape and reel)
800 ma fixed and adjustable output very low drop voltage regulator Features ery low dropout voltage (typ. 0.4 at 800 ma) Guaranteed output current up to 800 ma Fixed and adjustable output voltage (± 1
L79L00 SERIES NEGATIVE VOLTAGE REGULATORS
L79L00 SERIES NEGATIVE VOLTAGE REGULATORS OUTPUT CURRENT UP TO 100 ma OUTPUT VOLTAGES OF -5; -6; -8; -9; -12; -15 V THERMAL OVERLOAD PROTECTION SHORT CIRCUIT PROTECTION NO EXTERNAL COMPONENTS ARE REQUIRED
LD29300xx. 3 A, very low drop voltage regulators. Features. Description
3 A, very low drop voltage regulators Features Very low dropout voltage (Typ. 0.4 at 3 A) Guaranteed output current up to 3 A Fixed voltage with ± 1 % tolerance at 25 C Internal current and thermal limit
L78L00 SERIES POSITIVE VOLTAGE REGULATORS
L78L00 SERIES POSITIE OLTAGE REGULATORS OUTPUT CURRENT UP TO 100 OUTPUT OLTAGESOF 3.3; 5; ; 8; 9; 12; 15; 18; 24 THERMAL OERLOAD PROTECTION SHORT CIRCUIT PROTECTION NO EXTERNAL COMPONENTS ARE REQUIRED
AN922 Application note
Application note Using a Super Cap to back up the M41T56, M41T00 M41T11, M41T81, M41T94, and M41ST84W (16-pin) Introduction The M41T56, M41T00, M41T11, M41T81, M41T94, and M41ST84W (16-pin) real-time clocks
STTH60R04. Ultrafast recovery diode. Main product characteristics. Features and benefits. Description. Order codes
STTH6R4 Ultrafast recovery diode Main product characteristics I F(AV) 6 A V RRM T j 4 V 175 C A K V F (typ).95 V t rr (typ) 31 ns Features and benefits Very low switching losses High frequency and/or high
Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. L7900 SERIES NEGATIVE VOLTAGE REGULATORS OUTPUT CURRENT UP TO 1.5A OUTPUT
AN2970 Application note
Application note Principles of capacitive touch and proximity sensing technology The objective of this document is to present the principles of capacitive sensing and charge transfer used in STMicroelectronics
STM1831. Voltage detector with sense input and external delay capacitor. Features. Applications
Voltage detector with sense input and external delay capacitor Features Voltage monitored on separate sense input V SEN Factory-trimmed voltage thresholds in 100 mv increments from 1.6 V to 5.7 V ±2% voltage
STTH61R04TV. Ultrafast recovery diode. Main product characteristics. Features and benefits. Order codes. Description A1 K2 ISOTOP ISOTOP STTH61R04TV1
STTH61R4TV Ultrafast recovery diode Main product characteristics I F(AV) 2 x 3 A V RRM 4 V T j V F (typ) 15 C.95 V t rr (typ) 24 ns Features and benefits Ultrafast Very low switching losses High frequency
STTH16R04CT. Ultrafast recovery diode. Main product characteristics. Features and benefits. Description. Order codes TO-220AB TO-220FPAB
Ultrafast recovery diode Main product characteristics I F(AV) 2 X 8 A A1 A2 K V RRM 4 V T j 175 C V F (typ) t rr (typ).9 V 25 ns A1 K A2 A1 A2 K Features and benefits TO-22AB T TO-22FPAB FP Very low switching
T810H. High temperature 8 A sensitive TRIACs. Features. Applications. Description. Medium current TRIAC
T8H High temperature 8 A sensitive TRIACs Features Medium current TRIAC Logic level sensitive TRIAC 5 C max. T j turn-off commutation G Clip bounding A RoHS (22/95/EC) compliant packages Applications The
DO-15 DO-201AD STTH3R04Q STTH3R04
STTH3R4 Ultrafast recovery diode Features Negligible switching losses Low forward and reverse recovery times High junction temperature Description The STTH3R4 series uses ST's new 4 V planar Pt doping
LD1117A SERIES LOW DROP FIXED AND ADJUSTABLE POSITIVE VOLTAGE REGULATORS
LD1117A SERIES LOW DROP FIXED AND ADJUSTABLE POSITIVE VOLTAGE REGULATORS LOW DROPOUT VOLTAGE (1.15V TYP. @ I OUT = 1A, 25 C) VERY LOW QUIESCENT CURRENT (5 ma TYP. @ 25 C) OUTPUT CURRENT UP TO 1A FIXED
Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. LM117/217 LM317 1.2V TO 37V VOLTAGE REGULATOR OUTPUT VOLTAGE RANGE: 1.2
STTH6110TV. Ultrafast recovery - high voltage diode. Main product characteristics. Features and benefits. Order codes. Description ISOTOP ISOTOP
Ultrafast recovery - high voltage diode Main product characteristics I F(AV) V RRM T j V F (typ) t rr (typ) Features and benefits Ultrafast, soft recovery Very low conduction and switching losses High
Obsolete Product(s) - Obsolete Product(s)
Features W flyback SMPS demonstration board for alarm system based on the L99 and STPNKZ Input voltage: Vin: Vac (f: Hz) Output voltages: Vout =. V, Iout = A Vout = V, Iout= ma Vout =. V, Iout = ma (.9
STTH6006W. Turbo 2 ultrafast - high voltage rectifier. Features and benefits. Description. Main product characteristics
Turbo 2 ultrafast - high voltage rectifier Table 1. Main product characteristics I (AV) 6 A A K V RRM 6 V T j 175 C V (typ) 1.1 V t rr (max) 6 ns A eatures and benefits Ultrafast switching Low reverse
KD A LOW DROP POSITIVE VOLTAGE REGULATOR ADJUSTABLE AND FIXED
7.5A LOW DROP POSITIVE VOLTAGE REGULATOR ADJUSTABLE AND FIXED THREE TERMINAL ADJUSTABLE OR FIXED OUTPUT VOLTAGE 1.5V,1.8V, 2.5V, 3.0, 3.3V OUTPUT CURRENT UP TO 7.5A 1.4V MAX DROPOUT VOLTAGE AT FULL LOAD
STTH312B. Ultrafast recovery V diode. Main product characteristics. Features and benefits. Description. Order codes
STTH31 Ultrafast recovery - 1 V diode Main product characteristics I (AV) 3 A V RRM 1 V T j 175 C V (typ) 1.15 V t rr (typ) 55 ns K A K eatures and benefits Ultrafast, soft recovery Very low conduction
L7800 SERIES POSITIVE VOLTAGE REGULATORS
L7800 SERIES POSITIVE VOLTAGE REGULATORS OUTPUT CURRENT TO 1.5A OUTPUT VOLTAGES OF 5; 5.2; 6; 8; 8.5; 9; 10; 12; 15; 18; 24V THERMAL OVERLOAD PROTECTION SHORT CIRCUIT PROTECTION OUTPUT TRANSITION SOA PROTECTION
STTH15L06. Turbo 2 ultrafast high voltage rectifier. Description. Features
STTH15L6 Turbo 2 ultrafast high voltage rectifier Datasheet - production data Description K A K A The STTH15L6, which is using ST Turbo 2 6 V technology, is specially suited for use in switching power
L7800 SERIES POSITIVE VOLTAGE REGULATORS
L7800 SERIES POSITIVE VOLTAGE REGULATORS OUTPUT CURRENT TO 1.5A OUTPUT VOLTAGES OF 5; 5.2; 6; 8; 8.5; 9; 12; 15; 18; 24V THERMAL OVERLOAD PROTECTION SHORT CIRCUIT PROTECTION OUTPUT TRANSITION SOA PROTECTION
STPS20M60S. Power Schottky rectifier. Features. Description. High current capability Avalanche rated Low forward voltage drop High frequency operation
Power Schottky rectifier Features High current capability valanche rated Low forward voltage drop High frequency operation Description The is a single Schottky diode, suited for high frequency switch mode
L7800AB/AC SERIES PRECISION 1A REGULATORS
L7800AB/AC SERIES PRECISION 1A REGULATORS OUTPUT CURRENT IN EXCESS OF 1A OUTPUT VOLTAGES OF 5; 6; 8; 9; 12; 15; 18; 20; 24V THERMAL OVERLOAD PROTECTION OUTPUT TRANSITION SOA PROTECTION 2% OUTPUT VOLTAGE
LD1117A SERIES LOW DROP FIXED AND ADJUSTABLE POSITIVE VOLTAGE REGULATORS
LD1117A SERIES LOW DROP FIXED AND ADJUSTABLE POSITIVE VOLTAGE REGULATORS LOW DROPOUT VOLTAGE (1.15V TYP. @ I OUT =1A,25 C) VERY LOW QUIESCENT CURRENT (5 ma TYP. @ 25 C) OUTPUT CURRENT UP TO 1A FIXED OUTPUT
Description. Part numbers. AB version C version Output voltage LD2980ABM30TR LD2980ABM33TR LD2980CM33TR 3.3 V LD2980ABM50TR LD2980CM50TR 5.
Features SOT23-5L Stable with low ESR ceramic capacitors Ultra low dropout voltage (0.12 V typ. at 50 ma load, 7 mv typ. at 1 ma load) Very low quiescent current (80 µa typ. at no load in on mode; max
ST2L Very low quiescent current dual voltage regulator. Description. Features. Applications
Very low quiescent current dual voltage regulator Description Datasheet - production data Features DFN8 (5x6 mm) V O1 : fixed V O2 : adjustable from 1.25 to V I - V DROP Guaranteed current of output 1:
7.5A LOW DROP POSITIVE VOLTAGE REGULATOR ADJUSTABLE AND FIXED. October 2002
THREE TERMINAL ADJUSTABLE OR FIXED OUTPUT VOLTAGE 1.5V,1.8V, 2.5V, 3.0, 3.3V OUTPUT CURRENT UP TO 7.5A 1.4V MAX DROPOUT VOLTAGE AT FULL LOAD LINE REGULATION: MAX 0.2% OVER FULL TEMPERATURE RANGE LOAD REGULATION:
STTH3002. Ultrafast recovery diode. Main product characteristics. Features and benefits. Description. Order codes K DOP3I STTH3002PI DO-247 STTH3002W
Ultrafast recovery diode Main product characteristics I F(V) 3 K V RRM 2 V T j (max) 175 C V F (typ).77 V t rr (typ) 22 ns Features and benefits Very low conduction losses Negligible switching losses K
ST3L01 TRIPLE VOLTAGE REGULATOR
TRIPLE VOLTAGE REGULATOR DUAL INPUT VOLTAGE (12V AND 5V) TRIPLE OUTPUT VOLTAGE (2.6V, 3.3V, 8V) 2.6V GUARANTEED I OUT UP TO 1.2A 3.3V GUARANTEED I OUT UP TO 1.0A 8V GUARANTEED I OUT UP TO 200mA THERMAL
Obsolete Product(s) - Obsolete Product(s)
L494 MULTIFUNCTION OLTAGE REGULATOR FOR CAR RADIO PROGRAMMABLE OUTPUTS: TO (00mA); TO (00mA); TO (00mA) STANDBY OUT AND OUT2 WITH INDEPENDENT EN- ABLE CONTROL FOR STAND-BY MODE 0.4A HIGH SIDE DRIER LOAD
STPS60L30C-Y. Automotive power Schottky rectifier. Features. Description
Automotive power Shottky retifier Features ery small ondution losses Negligible swithing losses Extremely fast swithing AEC-Q11 qualified A1 A2 Desription Pin 1 6 A dual enter tab Shottky retifier suitable
LDL212. High PSRR, low drop linear regulator IC. Datasheet. Features. Applications. Description
Datasheet High PSRR, low drop linear regulator IC Features Input voltage from 2.5 V to 18 V 2 V AMR Any fixed output voltages, from 1.2 V to 12 V in 1 mv steps (from 1.2 V to 6.6 V in 5 mv steps) available
LD A high PSRR ultra low drop linear regulator with reverse current protection. Datasheet. Features. Applications.
Datasheet 2 A high PSRR ultra low drop linear regulator with reverse current protection Features Input voltage from 1.25 V to 6. V Ultra low drop: 13 mv (typ.) at 2 A load 1 % output accuracy at 25 C,
74VHCT138ATTR 3 TO 8 LINE DECODER (INVERTING)
3 TO 8 LINE DECODER (INVERTING) HIGH SPEED: t PD = 7.6 ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 4 µa (MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS: V IH = 2V (MIN.), V IL = 0.8V (MAX) POWER
Order code Marking Package Packaging. STGB30V60DF GB30V60DF D²PAK Tape & reel STGP30V60DF GP30V60DF TO-220 Tube
STGB30V60DF STGP30V60DF 600 V, 30 A very high speed trench gate fieldstop IGBT Datasheet preliminary data Features Maximum junction temperature : T J = 175 C Very high speed switching Negligible tail current
Symbol Parameter Value Unit V RRM Repetitive peak reverse voltage 150 V I F(RMS) RMS forward voltage 15 A
Power Schottky rectifier Main product characteristics I F(AV) V RRM j (max) V F (max) 3 A 15 V 175 C.67 V Description 15 V Power Schottky rectifier are suited for switch mode power supplies on up to 24
AN420 Application note
Application note Expanding A/D resolution of the ST6 A/D converter Introduction Occasionally the analog signal provided by external sensors require an Analog to Digital conversion with a resolution of
Obsolete Product(s) - Obsolete Product(s)
8-BIT PRIORITY ENCODER CONVERTS FROM 1 TO 8 TO INPUTS BINARY PROVIDES CASCADING FEATURE TO HANDLE ANY NUMBER OF INPUTS GROUP SELECT INDICATES ONE OR MORE PRIORITY INPUTS QUIESCENT CURRENT SPECIFIED UP
ESDAULC5-1BF4. Low clamping and ultra low capacitance single line bidirectional ESD protection. Applications. Description.
Low clamping and ultra low capacitance single line bidirectional ESD protection Applications Datasheet - production data Where transient over voltage protection in ESD sensitive equipment is required,
STTH12R06. Turbo 2 ultrafast high voltage rectifier. Features. Description
STTH12R6 Turbo 2 ultrafast high voltage rectifier eatures Ultrafast switching Low reverse recovery current Low thermal resistance Reduces switching losses Package insulation voltage: TO22C ins: 25 V RMS
STPS1545. Power Schottky rectifier. Main product characteristics. Features and Benefits. Description 15 A 45 V
Power Schottky rectifier Main product characteristics I F(V) V RRM T j (max) V F (max) Features and Benefits Very small conduction losses Negligible switching losses Extremely fast switching Insulated
STPS1L40M LOW DROP POWER SCHOTTKY RECTIFIER. Table 1: Main Product Characteristics I F(AV) V RRM. 1 A 40 V T j (max) 150 C V F (max) 0.
LOW DROP POWER SCHOTTKY RECTIFIER Table 1: Main Product Characteristics I F(AV) V RRM 1 A 40 V T j (max) 150 C V F (max) 0 V C A FEATURES AND BENEFITS Very small conduction losses Negligible switching
Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. STTH112/A/U HIGH VOLTAGE ULTRAFAST RECTIFIER Main product characteristics
LD1117 SERIES LOW DROP FIXED AND ADJUSTABLE POSITIVE VOLTAGE REGULATORS
LD7 SERIES LOW DROP FIXED AND ADJUSTABLE POSITIE OLTAGE REGULATORS LOW DROPOUT OLTAGE ( TYP) 2.85 DEICE PERFORMANCES ARE SUITABLE FOR SCSI-2 ACTIE TERMINATION OUTPUT CURRENT UP TO 800mA FIXED OUTPUT OLTAGE
STPS1045B. Power Schottky rectifier. Description. Features
Power Schottky rectifier Datasheet production data Description High voltage Schottky rectifier suited for switch mode power supply and other power converters. Packaged in DPAK, this device is intended
BAR42FILM BAR43FILM SMALL SIGNAL SCHOTTKY DIODE. Table 1: Main Product Characteristics I F(AV) 0.1 A V RRM. 30 V T j 150 C 0.33 and 0.
BR42FILM BR43FILM SMLL SIGNL SCHOTTY DIODE Table 1: Main Product Characteristics I F(V) 0.1 V RRM 30 V T j 150 C V F (max) 0.33 and 0.40 V FETURES ND BENEFITS Very small conduction losses Negligible switching
K G. Order code 400 V 600 V Min. Max. P0111MA 1AA3 X 4 µa 25 µa TO-92. P0111MN 5AA4 X 4 µa 25 µa SOT-223. P0115DA 5AL3 X 15 µa 50 µa TO-92
Sensitive high immunity SCRs up to.8 Features I T(RMS) up to.8 V DRM /V RRM and 6 V I GT from.5 to 5 µ G K Description Thanks to highly sensitive triggering levels, the P11xx SCR series is suitable for
STTH5L06RL. Turbo 2 ultrafast high voltage rectifier. Main product characteristics. Features and benefits. Order codes.
STTH5L6 Turbo 2 ultrafast high voltage rectifier Main product characteristics K I (V) 5 V RRM 6 V I R (max) 125 µ / 15 µ T j (max) 175 C V (max) 1.5 V K TO-22C STTH5L6D K TO-22PC STTH5L6P t rr (max) 95
STTH6004W. Ultrafast high voltage rectifier. Table 1: Main product characteristics I F(AV) 60 A V RRM. 400 V T j (max) 175 C V F (typ)
STTH64W Ultrafast high voltage rectifier Table 1: Main product characteristics I F(AV) 6 A V RRM 4 V T j (max) 175 C V F (typ).83 V t rr (max) 5 ns Features and benefits Ultrafast switching Low reverse
Very low conduction losses Low forward voltage drop Low thermal resistance High specified avalanche capability High integration ECOPACK 2 compliant
Datasheet 100 V, 30 A power Schottky rectifier Features Very low conduction losses Low forward voltage drop Low thermal resistance High specified avalanche capability High integration ECOPACK 2 compliant
ST2378E. 8-bit dual supply 1.71V to 5.5V level translator with I/O V CC ± 15KV ESD protection. General features. Description.
8-bit dual supply 1.71V to V level tralator with I/O V CC ± 15KV ESD protection General features High speed: t PD = 15 (Max.) at T A = 85 C V L = 1.8V V CC = V Guaranteed data rate: 13Mbps (1.8V V L V
STTH1210G. Ultrafast recovery - high voltage diode. Main product characteristics. Features and benefits. Description. Order codes K TO-220AC STTH1210D
STTH12 Ultrafast recovery - high voltage diode Main product characteristics I F(V) 12 K V RRM V T j 175 C V F (typ) 1.3 V t rr (typ) 48 ns Features and benefits Ultrafast, soft recovery Very low conduction
2N3904 SMALL SIGNAL NPN TRANSISTOR
SMALL SIGNAL NPN TRANSISTOR PRELIMINARY DATA Ordering Code Marking Package / Shipment TO-92 / Bulk -AP TO-92 / Ammopack SILICON EPITAXIAL PLANAR NPN TRANSISTOR TO-92 PACKAGE SUITABLE FOR THROUGH-HOLE PCB
Table 3: Absolute Ratings (limiting values) Symbol Parameter Value Unit I T(RMS)
TYN61M 1 SCR Table 1: Main Features Symbol Value Unit I T(RMS) 1 V DRM /V RRM 6 V I T (min./max.) 1.5 / 5 m K DESCRIPTION The TYN61M SCR is suitable to fit modes of control found in applications such as
AN1755 APPLICATION NOTE
AN1755 APPLICATION NOTE A HIGH RESOLUTION / PRECISION THERMOMETER USING ST7 AND NE555 INTRODUCTION The goal of this application note is to present a realistic example of a thermometer using an ST7 and
TDA7439DS. Three-band digitally-controlled audio processor. Features. Description
Three-band digitally-controlled audio processor Features! Input multiplexer four stereo inputs selectable input gain for optimal adaptation to different sources! Single stereo output! Treble, mid-range
Silicon carbide Power MOSFET 650 V, 90 A, 18 mω (typ., T J = 25 C) in an H²PAK-7 package. Order code V DS R DS(on) max. I D
Datasheet Silicon carbide Power MOSFET 650 V, 90 A, 18 mω (typ., T J = 25 C) in an H²PAK-7 package TAB Features Order code V DS R DS(on) max. I D 1 H2PAK-7 7 SCTH90N65G2V-7 650 V 25 mω 90 A Very high operating
High brightness RGB LED array driver with local dimming and diagnostics based on the LED1642GW and STM32
STEVAL-ILL0V High brightness RGB D array driver with local dimming and diagnostics based on the DGW and STM Data brief Features High brightness x RGB D matrix Complete hardware and software package Various
Obsolete Product(s) - Obsolete Product(s)
STTH124TV1 Ultrafast high voltage rectifier Table 1: Main product characteristics I F(AV) 2 x 6 A V RRM 4 V T j (max) 15 C V F (typ) t rr (max) Features and benefits Ultrafast switching Low reverse current
STD5N20L N-CHANNEL 200V Ω - 5A DPAK STripFET MOSFET
N-CHANNEL 200V - 0.65Ω - 5A DPAK STripFET MOSFET Table 1: General Features TYPE V DSS R DS(on) I D Pw Figure 1: Package STD5N20L 200 V < 0.7 Ω 5 A 33 W TYPICAL R DS (on) = 0.65 Ω @ 5V CONDUCTION LOSSES
STPS2H V power Schottky rectifier. Datasheet. Features. Description. Negligible switching losses
Datasheet 100 V power Schottky rectifier Features A Negligible switching losses A High junction temperature capability Low leakage current K SMA K SMB Good trade-off between leakage current and forward
Obsolete Product(s) - Obsolete Product(s)
8-INPUT NAND GATE HIGH SPEED: t PD = 13ns (TYP.) at V CC = 6V LOW POWER DISSIPATION: I CC = 1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28 % V CC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE: I
STPSC15H V power Schottky silicon carbide diode. Datasheet. Features A. Description. No or negligible reverse recovery
Datasheet 1200 V power Schottky silicon carbide diode Features A K No or negligible reverse recovery K K Switching behavior independent of temperature Robust high voltage periphery Operating from -40 C
BCM857BV; BCM857BS; BCM857DS
BCM857BV; BCM857BS; BCM857DS Rev. 05 27 June 2006 Product data sheet 1. Product profile 1.1 General description in small Surface-Mounted Device (SMD) plastic packages. The transistors are fully isolated
M74HC20TTR DUAL 4-INPUT NAND GATE
DUAL 4-INPUT NAND GATE HIGH SPEED: t PD = 9ns (TYP.) at V CC = 6V LOW POWER DISSIPATION: I CC = 1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28 % V CC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE:
HCF4532B 8-BIT PRIORITY ENCODER
8-BIT PRIORITY ENCODER CONVERTS FROM 1 TO 8 TO INPUTS BINARY PROVIDES CASCADING FEATURE TO HANDLE ANY NUMBER OF INPUTS GROUP SELECT INDICATES ONE OR MORE PRIORITY INPUTS QUIESCENT CURRENT SPECIFIED UP
STTH8R06. Turbo 2 ultrafast high voltage rectifier. Description. Features
Turbo 2 ultrafast high voltage rectifier Description Datasheet - production data The STTH8R06, which uses ST Turbo 2 600 V technology, is specially suited as boost diode in continuous mode power factor
Obsolete Product(s) - Obsolete Product(s)
DUAL BINARY TO 1 OF 4 DECODER/DEMULTIPLEXER OUTPUT LOW ON SELECT EXPANDABLE WITH MULTIPLE PACKAGES STANDARDIZED SYMMETRICAL OUTPUT CHARACTERISTICS QUIESCENT CURRENT SPECIFIED UP TO 20V 5V, 10V AND 15V
HCF4555B DUAL BINARY TO 1 OF 4 DECODER/DEMULTIPLEXER OUTPUT HIGH ON SELECT
DUAL BINARY TO 1 OF 4 DECODER/DEMULTIPLEXER OUTPUT HIGH ON SELECT EXPANDABLE WITH MULTIPLE PACKAGES STANDARDIZED SYMMETRICAL OUTPUT CHARACTERISTICS QUIESCENT CURRENT SPECIFIED UP TO 20V 5V, 10V AND 15V
STTH212RL. High voltage ultrafast diode. Main product characteristics. Features and benefits. Order codes. Description DO-201AD STTH212
High voltage ultrafast diode Main product characteristics I F(AV) 2 A A K V RRM 12 V T j 175 C V F (typ) 1. V t rr (max) Features and benefits Low forward voltage drop High reliability High surge current
65 V, 100 ma NPN/PNP general-purpose transistor. Table 1. Product overview Type number Package NPN/NPN PNP/PNP Nexperia JEITA
Rev. 1 17 July 29 Product data sheet 1. Product profile 1.1 General description NPN/PNP general-purpose transistor pair in a very small Surface-Mounted Device (SMD) plastic package. Table 1. Product overview
Obsolete Product(s) - Obsolete Product(s)
3 TO 8 LINE DECODER HIGH SPEED: t PD = 15ns (TYP.) at V CC = 6V LOW POWER DISSIPATION: I CC = 4µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28 % V CC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE:
BTA12, BTB12 and T12 Series
BTA12, BTB12 and T12 Series SNUBBERLESS, LOIC LEVEL & STANDARD 12A TRIACS Table 1: Main Features Symbol Value Unit I T(RMS) 12 A V DRM /V RRM 6 and 8 V I T (Q1 ) 5 to 5 ma A1 DESCRIPTION Available either
T4 Series 4A TRIACS. Table 1: Main Features Symbol Value Unit I T(RMS) 4 A. V DRM /V RRM 600 to 800 V. I GT (Q1 ) 5 to 35 ma
T4 Series SNUBBERLESS & LOIC LEVEL 4A TRIACS Table 1: Main Features Symbol Value Unit I T(RMS) 4 A V DRM /V RRM 600 to 800 V I T (Q1 ) 5 to 35 ma DESCRIPTION Based on ST s Snubberless / Logic level technology
Automotive-grade 400 V internally clamped IGBT E SCIS 320 mj
STGB25N40LZAG, STGD25N40LZAG Datasheet Automotive-grade 400 V internally clamped IGBT E SCIS 320 mj Features TAB D 2 PAK 2 1 3 TAB 2 1 DPAK 3 AEC-Q101 qualified SCIS energy of 320 mj @ T J = 25 C Parts
STTH3R06RL TURBO 2 ULTRAFAST HIGH VOLTAGE RECTIFIER. Table 1: Main Product Characteristics I F(AV) V RRM
STTH3R6 TURBO 2 ULTRAAST HIGH VOLTAGE RECTIIER Table 1: Main Product Characteristics I (AV) V RRM 3 A 6 V I R (max) 1 µa T j 175 C V (typ) 1. V t rr (typ) 35 ns A K EATURES AND BENEITS Ultrafast switching
Obsolete Product(s) - Obsolete Product(s)
BCD TO DECIMAL DECODER HIGH SPEED : t PD = 14ns (TYP.) at V CC = 6V LOW POWER DISSIPATION: I CC =4µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28 % V CC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE:
Obsolete Product(s) - Obsolete Product(s)
Three-band digitally-controlled audio processor Features! Input multiplexer four stereo inputs selectable input gain for optimal adaptation to different sources! Single stereo output! Treble, mid-range
M74HCT688TTR 8 BIT EQUALITY COMPARATOR
8 BIT EQUALITY COMPARATOR HIGH SPEED: t PD = 21ns (TYP.) at V CC = 4.5V LOW POWER DISSIPATION: I CC = 4µA(MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS : V IH = 2V (MIN.) V IL = 0.8V (MAX) SYMMETRICAL
TURBO 2 ULTRAFAST HIGH VOLTAGE RECTIFIER
STTH5R6 TURBO 2 ULTRST HIGH VOLTGE RECTIIER Table 1: Main Product Characteristics I (V) 5 V RRM 6 V T j 175 C V (typ) 1.4 V t rr (max) 4 ns ETURES ND BENEITS Ultrafast switching Low reverse recovery current
Obsolete Product(s) - Obsolete Product(s)
N-CHANNEL 3A - 600 D 2 PAK Power MESH IGBT TYPE CES CE(sat) I c STGB3NB60SD 600
TURBO 2 ULTRAFAST HIGH VOLTAGE RECTIFIER
TURBO 2 ULTRAAST HIGH VOLTAGE RECTIIER Table 1: Main Product Characteristics I (AV) Up to 2 x A V RRM 6 V T j 175 C V (typ).95 V t rr (max) 55 ns EATURES AND BENEITS Ultrafast switching Low reverse current
STEVAL-MKI109V2. emotion: ST MEMS adapters motherboard based on the STM32F103RE compatible with all ST MEMS adapters. Features.
EVAL-MKI0V emotion: MEMS adapters motherboard based on the MFE compatible with all MEMS adapters Data brief Features Compatible with all available MEMS adapter boards Controlled by the MFET highperformance
M74HCT138TTR 3 TO 8 LINE DECODER (INVERTING)
3 TO 8 LINE DECODER (INVERTING) HIGH SPEED: t PD = 16ns (TYP.) at V CC = 4.5V LOW POWER DISSIPATION: I CC = 4µA(MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS : V IH = 2V (MIN.) V IL = 0.8V (MAX) SYMMETRICAL
Small Signal Zener Diodes, Dual
Small Signal Zener Diodes, Dual DESIGN SUPPORT TOOLS Models Available PRIMARY CHARACTERISTICS 6 PARAMETER VALUE UNIT range nom.. to V Test current T specification Pulse current Circuit configuration Dual
ULTRAFAST RECTIFIER PDP ENERGY RECOVERY
STTH40P03S ULTRST RECTIIER PDP ENERGY RECOVERY Table 1: Main Product Characteristics I (V) 40 V RRM 300 V V P (typ) 2.5 V I RM (typ) 5 T j 175 C V (typ) 0.9 V ETURES ND BENEITS Ultrafast recovery allowing
M74HC147TTR 10 TO 4 LINE PRIORITY ENCODER
10 TO 4 LINE PRIORITY ENCODER HIGH SPEED: t PD = 15ns (TYP.) at V CC = 6V LOW POWER DISSIPATION: I CC = 4µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28 % V CC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE:
STTH10R04. High efficiency rectifier. Description. Features
STTH1R4 High efficiency rectifier Datasheet - production data Features K A A NC D 2 PAK K Ultrafast recovery Low power losses High surge capability Low leakage current High junction temperature ECOPACK
STTH5L06. Turbo 2 ultrafast high voltage rectifier. Description. Features
Turbo 2 ultrafast high voltage rectifier Description Datasheet - production data The STTH5L06 is developed using St's Turbo 2 600 V technology. It is well-suited as a boost diode, especially for use in
Small Signal Zener Diodes, Dual
DZ-G Series Small Signal Zener Diodes, Dual PRIMARY CHARACTERISTICS PARAMETER ALUE UNIT range nom.. to Test current T specification Pulse current Int. construction Dual common cathode FEATURES Dual silicon
Negligible switching losses. Low forward voltage drop Surface mount miniature packages Avalanche rated ECOPACK 2 compliant
Datasheet 60 V - 1 power Schottky rectifier K Features Negligible switching losses K SM K DO-41 Low forward voltage drop Surface mount miniature packages valanche rated ECOPCK 2 compliant K STmite flat
Features. Description. Table 1. Device summary. Order code Marking Packages Packing. STGD19N40LZ GD19N40LZ DPAK Tape and reel
Automotive-grade 390 V internally clamped IGBT E SCIS 180 mj Features Datasheet - production data TAB DPAK 1 3 AEC-Q101 qualified 180 mj of avalanche energy @ T C = 150 C, L = 3 mh ESD gate-emitter protection
Obsolete Product(s) - Obsolete Product(s)
DUAL 4 CHANNEL MULTIPLEXER 3 STATE OUTPUT HIGH SPEED: t PD = 16ns (TYP.) at V CC = 6V LOW POWER DISSIPATION: I CC = 4µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28 % V CC (MIN.) SYMMETRICAL
SCT10N120. Silicon carbide Power MOSFET 1200 V, 12 A, 520 mω (typ., T J = 150 C) in an HiP247 package. Datasheet. Features. Applications.
Datasheet Silicon carbide Power MOSFET 12 V, 12 A, 52 mω (typ., T J = 15 C) in an HiP247 package Features Very tight variation of on-resistance vs. temperature Very high operating junction temperature
STTH60SW03C. Turbo 2 ultrafast high voltage rectifier. Description. Features
STTH6SW3C Turbo 2 ultrafast high voltage rectifier A1 A2 K Description Datasheet production data The STTH6SW3C uses ST Turbo 2 3 V technology. It is especially suited to be used for DC/DC and DC/AC converters
STPS30SM100S. Power Schottky rectifier. Features. Description
Power Schottky rectifier Features High current capability valanche rated Low forward voltage drop current High frequency operation Insulated package: Insulation voltage 2000 V rms Package capacitance =
STTH10LCD06. Turbo 2 ultrafast - high voltage rectifier for flat panel displays. Description. Features
STTH1LCD6 Turbo 2 ultrafast - high voltage rectifier for flat panel displays Description Datasheet - production data The STTH1LCD6 uses ST Turbo 2 technology. This device is suited for power applications