PERFORMANCE SPECIFICATION SHEET TRANSFORMERS, AUDIO FREQUENCY, ULTRA-MINIATURE
|
|
- Bartholomew McCarthy
- 5 years ago
- Views:
Transcription
1 INCH-POUND September 00 SUPERSEDING MIL-PRF-7/7B 1 June 88 PERFORMNCE SPECIFICTION SHEET TRNSFORMERS, UDIO FREQUENCY, ULTR-MINITURE This specification is approved for use by all Departments and gencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification and MIL-PRF-7. Inches mm NOTES: 1. Dimensions are in inches.. Metric equivalents are given for general information only.. Marking shall be on the side of the case.. and secondary electrical values, specified in table I, shall be marked as applicable.. Dots on circuit indicate polarity. FIGURE 1. Dimensions and. MSC N/ 1 of 7 FSC 90 DISTRIBUTION STTEMENT. pproved for public release; distribution is unlimited.
2 REQUIREMENTS: Electrical ratings: See table I. Working voltage (peak): 100 volts. Frequency range: 00 Hz to 7 khz. Design and construction: Dimensions and : See figure 1. Duty cycle: Continuous. Terminals: Solid wire. Composition: Copper clad steel. Diameter: inch ±0.001 (0.1 ±0.0 mm). Length: 0 inch ±0. (. ±6. mm). Final finish: Tinned, 100 percent, electroplated in accordance with STM B. Weight: grams max. ltitude: 10,000 feet, maximum. Operating temperature range: - C to +10 C. Terminal strength: MIL-STD-0, method 11, test condition,.0 pounds. Thermal shock: cycles, method 107, MIL-STD-0, test condition -1. Vibration (high frequency): MIL-STD-0, method 0, test condition B. Dielectric withstanding voltage: t sea level: 00 V rms. t barometric pressure: 00 V rms. Electrical characteristics: No load (center tap ): ±1 percent at 1 volt, khz across the primary. Harmonic distortion: Total harmonic content of output shall be a maximum of percent at the specified power level (see table I). Insertion loss: t the specified power level (see table I), the insertion loss shall be a maximum of.0 db at 1 khz. Frequency response: ± db at the rated source and load s (see table 1) with mw level output and a reference frequency of 1 khz over a frequency range of 00 Hz to 7 khz.. Polarity: dditive when appropriate terminals are connected. For, connect terminals and, and 6. For B, connect terminals and (see figure 1, s and B).
3 TBLE I. Electrical ratings. 1/ Dash ct 0 ct ct 8 ct 80 ct 10 ct 10 ct 10 ct ct 00 ct 00 ct 00 ct 00 ct 00 ct 0 ct Impedance connec- tion 8 ct 0 ct ct ct 1.8 ct 60 ct 10 ct 1 ct 1 00 ct 1 ct 1 00 ct 1.8 ct 10 ct 00 ct 000 ct 1.8 ct dc dc connec- tion :secondary 1.8:1 :1 1.8:1 1.8:1.06:1 1..:1 :1 1.:1 1: :1.: :1.16:1 1.8: :. 1:.16 6.:1.6:1.16:1 1.8:1.16:1 :1 :1 :1.6:1 :1.16:1.16:1 :1 6..8:1 :1 8:1.6:1.:1 :1 :1.9:1.8:1 : :1.6:1.8:1 :1 1.6: :1 11.:1 6.:1.6:1 See footnotes at end of table.
4 TBLE I. Electrical ratings Continued. 1/ Dash ct 900 ct 1060 ct ct 1.8 ct 0 ct 8 ct 00 ct 1.8 ct 1.8 ct 8 ct 1 ct 1.8 ct 1.8 ct 1 ct ct 8 ct dc dc :secondary.1 :1.7:1.:1 :1 1. 7:1.6:1 7.9:1.08:1 1.:1 9..7: :1 1.:1 11.:1 :1 1.8:1 11.:1 1.8:1 :1 1.8:1 :1 8.9:1 7:1.6:1 : :1 1.8:1 8.16:1 :1.:1 18.:1 8.9:1 :1 18.:1.:1. :1.:1.6:1.:1 1.6:1 B / B / B / B / B / See footnotes at end of table
5 TBLE I. Electrical ratings Continued. 1/ Dash ct 000 ct 000 ct 000 ct 000 ct 000 ct 000 ct ct 000 ct 000 ct 000 ct 000 ct 000 ct ct 9000 ct 1.8 ct 00 ct dc dc :secondary 1: 1.8:1.8:1 :1.1.16:1 1.:1 8.66:1.:1 :1 :1.8:1.8:1 8:1 :1 7:1.7:1.08:1.16:1.89:1 :1 :1 :1 :1 1.6:1.16:1 :1 6.:1 :1.:1.:1 7:1.6:1 0:1.66:1 6:1 0:1 0: :1 8.16:1 6.:1.77:1 B / B / B / B / B / B / See footnotes at end of table.
6 TBLE I. Electrical ratings - Continued. 1/ 6 Das h ,000 ct 1,000 ct 1,000 ct 1,000 ct 1,000 ct 1,000 ct 16,000 ct 0,000 ct 0,000 ct 0,000 ct 0,000 ct 0,000 ct 0,000 ct ct 000 ct 7 1,000 ct 1,000 ct 000 ct dc dc :secondary.8:1.: :1 :1 1.:1 :1 6.:1.77:1 :1.7:1 : :1.7:1.8:1.:1 :1 1.: :1.:1 :1 8:1 1.6:1 11.:1 8.9:1 :1.8:1 B / B / 1/ Qualification testing and approval to M7/7-0 and M7/7-11 shall be sufficient to grant approval to M7/7-001 through M7/7-11. / Includes electrostatic shield. Shield terminal shall be. Voltage ratio shall be to 1 at 0 khz.
7 Self-resonance: The self-resonant frequency shall be greater than 10 khz when measured with the secondaries carrying the specified load and the secondary voltage observed. Power output in watts (max):. at 00 Hz and higher,. at 00 and higher,.6 at 1 khz and higher. Marking location: See figure 1. Part or Identifying Number (PIN): M7/7- (dash number from table I) Custodians: Preparing activity: rmy - CR DL - CC Navy - EC ir Force - 11 (Project ) DL - CC Review activities: rmy - R, CR Navy - S, MC, OS ir Force
PERFORMANCE SPECIFICATION SHEET
INCH-POUND MIL-PRF-49464/1C 24 June 2009 SUPERSEDING MIL-PRF-49464/1B 3 June 2004 PERFORMANCE SPECIFICATION SHEET CAPACITORS, CHIP, SINGLE LAYER, FIXED UNENCAPSULATED, CERAMIC DIELECTRIC, ESTABLISHED RELIABILITY,
More informationPERFORMANCE SPECIFICATION SHEET
INCH-POUND MIL-PRF-39003/1H 17 May 1996 SUPERSEDING MIL-PRF-39003/1G 31 January 1992 PERFORMANCE SPECIFICATION SHEET CAPACITOR, FIXED, ELECTROLYTIC (SOLID ELECTROLYTE), TANTALUM (POLARIZED, SINTERED SLUG),
More informationPERFORMANCE SPECIFICATION SHEET SWITCHES, THERMOSTATIC, (BIMETALLIC), TYPE I, SINGLE POLE, SINGLE THROW (SPST), 5 AMPERES
INCH-POUND MIL-PRF-24236/2J 17 April 2018 SUPERSEDING MIL-PRF-24236/2J w/amendment 2 10 January 2017 PERFORMANCE SPECIFICATION SHEET SWITCHES, THERMOSTATIC, (BIMETALLIC), TYPE I, SINGLE POLE, SINGLE THROW
More informationPERFORMANCE SPECIFICATION SHEET
INCH-POUND MIL-PRF-22885/77F 2 August 2018 SUPERSEDING MIL-PRF-22885/77E 25 April 2013 PERFORMANCE SPECIFICATION SHEET SWITCHES, PUSH BUTTON, ILLUMINATED, 4-LAMP, 0.75 SQUARE, 7.5 AMPERES, AND LOW LEVEL
More informationDETAIL SPECIFICATION SHEET
INCH POUND MIL DTL 28803/1E 1 September 2018 SUPERSEDING MIL D 28803/1E 4 September 2013 DETAIL SPECIFICATION SHEET DISPLAY, OPTOELECTRONIC, SEGMENTED READOUT, BACKLIGHTED, STYLE II (LIGHT EMITTING DIODE),
More informationPERFORMANCE SPECIFICATION SHEET
INCH-POUND MIL-PRF-22885/90C 17 MARCH 1999 SUPERSEDING MIL-S-22885/90B 23 June 1989 PERFORMANCE SPECIFICATION SHEET SWITCH, PUSHBUTTON, ILLUMINATED, 4-LAMP 0.750 SQUARE, LOW LEVEL TO 7 AMPERES, (DRIPPROOF,
More informationMILITARY SPECIFICATION MICROCIRCUITS, DIGITAL, BIPOLAR, TTL, DECODERS MONOLITHIC SILICON. Inactive for new design after 7 September 1995.
INCH-POUND 16 February 2005 SUPERSEDING MIL-M-38510/10C 3 March 1986 MILITARY SPECIFICATION MICROCIRCUITS, DIGITAL, BIPOLAR, TTL, DECODERS MONOLITHIC SILICON This specification is approved for use by all
More informationMILITARY SPECIFICATION MICROCIRCUITS, LINEAR, LOW OFFSET OPERATIONAL AMPLIFIERS, MONOLITHIC SILICON
INCH-POUND MIL-M-38510/135G 22 March 2010 SUPERSEDING MIL-M-38510/135F 8 April 2008 MILITARY SPECIFICATION MICROCIRCUITS, LINEAR, LOW OFFSET OPERATIONAL AMPLIFIERS, MONOLITHIC SILICON Reactivated after
More informationMILITARY SPECIFICATION MICROCIRCUITS, DIGITAL, BIPOLAR, SCHOTTKY TTL, FLIP-FLOPS, CASCADABLE, MONOLITHIC SILICON
INCH-POUND 2 November 2005 SUPERSEDING MIL-M-38510/71C 23 July 1984 MILITARY SPECIFICATION MICROCIRCUITS, DIGITAL, BIPOLAR, SCHOTTKY TTL, FLIP-FLOPS, CASCADABLE, MONOLITHIC SILICON This specification is
More informationSTANDARD MICROCIRCUIT DRAWING MICROCIRCUIT, LINEAR, 4-CHANNEL DIFFERENTIAL, ANALOG MULTIPLEXER, MONOLITHIC SILICON
REVISIONS LTR DESCRIPTION DTE (YR-MO-D) PPROVED Update boilerplate paragraphs to current MIL-PRF-38535 requirements. Delete references to device class M requirements. - ro 12-10-29 C. SFFLE REV REV REV
More informationMICROCIRCUITS, DIGITAL, TTL, FLIP-FLOPS, MONOLITHIC SILICON. Inactive for new design after 7 September 1995
MILITARY SPECIFICATION INCH-POUND MIL-M-38510/2G 8 February 2005 SUPERSEDING MIL-M-38510/2E 24 December 1974 MIL-M-0038510/2F (USAF) 24 OCTOBER 1975 MICROCIRCUITS, DIGITAL, TTL, FLIP-FLOPS, MONOLITHIC
More informationReactivated after 17 Jan and may be used for new and existing designs and acquisitions.
C-POUND MI-M-38510/653 17 January 2006 SUPERSEDG MI-M-38510/653 15 January 1988 MIITRY SPECIFICTION MICROCIRCUITS, DIGIT, IG-SPEED CMOS, FIP-FOPS, MONOITIC SIICON, POSITIVE OGIC This specification is approved
More informationREVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED. A Delete all match referenced tests as specified under Table I. - ro C.
REVISIONS LTR DESCRIPTION DTE (YR-MO-D) PPROVED Delete all match referenced tests as specified under Table I. - ro 16-04-04 C. SFFLE REV REV REV STTUS REV OF S 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/
More informationDEPARTMENT OF DEFENSE TEST METHOD STANDARD METHOD 304, RESISTANCE-TEMPERATURE CHARACTERISTIC
INCH-POUND MIL-STD-202-304 18 April 2015 SUPERSEDING MIL-STD-202G w/change 2 (IN PART) 28 June 2013 (see 6.1) DEPARTMENT OF DEFENSE TEST METHOD STANDARD METHOD 304, RESISTANCE-TEMPERATURE CHARACTERISTIC
More informationSTANDARD MICROCIRCUIT DRAWING MICROCIRCUIT, LINEAR, CMOS 8-BIT DAC WITH OUTPUT AMPLIFIER, MONOLITHIC SILICON
REVISIONS LTR DESCRIPTION DTE (YR-MO-D) PPROVED Drawing updated to reflect current requirements. - ro 03-01-28 R. MONNIN REV REV REV STTUS REV OF S 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/ STNDRD MICROCIRCUIT
More informationMILITARY SPECIFICATION MICROCIRCUITS, DIGITAL, BIPOLAR, TTL, MONOSTABLE MULTIVIBRATORS, MONOLITHIC SILICON
INCH-POUND MIL-M-38510/12J 22 February 2005 SUPERSEDING MIL-M-38510/12H 16 December 2003 MILITARY SPECIFICATION MICROCIRCUITS, DIGITAL, BIPOLAR, TTL, MONOSTABLE MULTIVIBRATORS, MONOLITHIC SILICON This
More informationMILITARY SPECIFICATION MICROCIRCUITS, LINEAR, CMOS/ANALOG MULTIPLEXERS/DEMULTIPLEXERS WITH OVERVOLTAGE PROTECTION, MONOLITHIC SILICON, POSITIVE LOGIC
INCH-POUND 12 October 2005 SUPERSEDING MIL-M-38510/190C 22 October 1986 MILITARY SPECIFICATION MICROCIRCUITS, LINEAR, CMOS/ANALOG MULTIPLEXERS/DEMULTIPLEXERS WITH OVERVOLTAGE PROTECTION, MONOLITHIC SILICON,
More informationMICROCIRCUIT, HYBRID, CMOS, LINEAR, ANALOG MULTIPLEXER, 64 CHANNEL, +3.3 TO +5 VOLT
REVISIONS LTR DESCRIPTION DTE (YR-MO-D) PPROVED REV REV 15 16 17 18 19 20 REV STTUS REV OF S 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/ STNDRD MICROCIRCUIT DRWING THIS DRWING IS VILBLE FOR USE BY LL DEPRTMENTS
More informationSeries FEATURES AND BENEFITS INTRODUCTION. Figure 1 Power Derating Curve. Table 1 Tolerance and TCR vs. Resistance
The 303143 Series Ultra The High-Precision 303143 Series Fixed Resistor Z-Foil Z201 Ultra High-Precision Fixed Resistor Z-Foil Z201 Screen/Test Flow as modified from S-311-P813 Proposed by NASA FEATURES
More informationSERIAL ATA POWER CONNECTOR 1.27 mm PITCH
: 1.27 mm PITCH TBLE OF CONTENTS 1.0 SCOPE 2.0 PPLICBLE DOCUMENTS 3.0 MTERIL SPECIFICTIONS 3.1 DESIGN ND CONSTRUCTION 3.2 MTERILS 4.0 PERFORMNCE ND TEST 5.0 TEST REQUIREMENTS ND PROCEDURES SHT 1 2 3 4
More informationMICROCIRCUITS, DIGITAL, BIPOLAR LOW-POWER SCHOTTKY TTL, FLIP-FLOPS, CASCADABLE, MONOLITHIC SILICON. Inactive for new design after 18 April 1997.
INCH-POUND MIL-M-38510/301F 4 March 2004 SUPERSEDING MIL-M-38510/301E 14 February 2003 MILITARY SPECIFICATION MICROCIRCUITS, DIGITAL, BIPOLAR LOW-POWER SCHOTTKY TTL, FLIP-FLOPS, CASCADABLE, MONOLITHIC
More informationSeries CCT-58S Multi-Throw DC 18 GHz, SP7T & SP8T Normally Open Coaxial Switch
PART NUMBER CCT-58S DESCRIPTION Commercial Normally Open Multi-throw, DC-18 GHz The CCT-58S/CT-58S is an internally terminated, broadband, multi-throw, electromechanical coaxial switch designed to switch
More informationMICROCIRCUITS, DIGITAL, LOW-POWER SCHOTTKY TTL, COUNTERS, MONOLITHIC SILICON. Inactive for new design after 18 April 1997.
INCH-POUND MIL-M-38510/315D 27 October 2003 SUPERSEDING MIL-M-38510/315C 17 JANUARY 1984 MILITARY SPECIFICATION MICROCIRCUITS, DIGITAL, LOW-POWER SCHOTTKY TTL, COUNTERS, MONOLITHIC SILICON This specification
More informationMilitary Qualified 10AT Series Snap Action Precision Position Switches
Military Qualified 10AT Series Snap Action Precision Position Switches FEATURES Stainless steel, hermetic seal construction Rated up to 4 amps, 30VDC MIL-PRF-8805 qualified Various mounting configurations
More informationProduct Data Sheet PD-0037-B
Product Data Sheet PD-0037-B 3M Shielded Compact Ribbon (SCR) Connector 3M Shielded Compact Ribbon (SCR) Boardmount Right Angle 36110-2220 XX 3 Electronic Solutions Division Page: 1 of 12 Table of Contents
More informationChip Inductors. LCCM Series Chip Common Mode Filter FEATURES CONSTRUCTION
FEATURES Small wire wound chip inductor with ferrite core and 2 common mode lines. Highly effective in noise suppression High common-mode impedance at noise band an low differential mode impedance at signal
More informationREVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED REV SHEET REV SHEET 15 REV STATUS OF SHEETS SHEET
REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED REV REV 15 REV STATUS REV OF S 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A MICROCIRCUIT DRAWING PREPARED BY Greg Cecil CHECKED BY Greg Cecil http://www.landandmaritime.dla.mil/
More informationProduct Series Specification Document
Product Series 3.96mm pitch board-to-board connectors - Socket SCOPE This document covers 3.96mm socket connectors. The connector will perform to the specifications outlined. All tests have been performed
More informationSuperTan Extended (STE) Capacitors, Wet Tantalum Capacitors with Hermetic Seal
SuperTan Extended () Capacitors, Wet Tantalum Capacitors with Hermetic Seal FEATURES SuperTan Extended () represents a major breakthrough in wet tantalum capacitor Available technology. Its unique cathode
More informationMICROCIRCUITS, DIGITAL, BIPOLAR, ADVANCED SCHOTTKY TTL, DECADE COUNTERS, MONOLITHIC SILICON
INCH-POUND MIL-M-38510/344A 14 April 2004 SUPERSEDING MIL-M-38510/344 12 June 1986 MILITARY SPECIFICATION MICROCIRCUITS, DIGITAL, BIPOLAR, ADVANCED SCHOTTKY TTL, DECADE COUNTERS, MONOLITHIC SILICON This
More informationAMERICAN CAPACITOR CORPORATION METALLIZED POLYPROPYLENE CAPACITORS ENVIRONMENTAL DATA
AMERICAN CAPACITOR CORPORATION ENVIRONMENTAL DATA SERIES N ENGINEERING DATA SHEET APPLICATIONS The N series Metallized Polypropylene capacitors are ideally suited for applications requiring low Dissipation
More informationFEATURES. Note 138D 306 X0 006 C 2 E3 MODEL CAPACITANCE CAPACITANCE TOLERANCE DC VOLTAGE RATING AT +85 C
Wet Tantalum Capacitors Silver Case TANTALEX Capacitors Hermetically-Sealed FEURES Terminations: axial, standard tin / lead (SnPb), 100 % tin (RoHS-compliant) available Available Model is the commercial
More information(Note 1) RH1086M ADJ 15V CAPACITOR(S) NOT SHOWN BOTTOM VIEW BOTTOM VIEW V IN ADJ 2 INPUT 1 FINAL SPECIFICATIONS SUBJECT TO CHANGE
RH086M and. Low Dropout Positive djustable Regulators DESCRIPTION The RH086M positive adjustable regulator is designed to provide for the H package and. for the K package with higher efficiency than currently
More informationPRODUCT SPECIFICATION
1 of 10 H 1.0 GENERAL THIS SPECIFICATION COVERS.039 INCHES VERTICAL DDR II SOCKETS WITH BLANKED / FORMED CONTACT DESIGNED FOR PRINTED WIRING BOARD TO DUAL IN-LINE MEMORY MODULE INTERCONNECTION. IN ALL
More information3M Pak 10 Plug, PK10 series PK10-XXXPX-X-DA. 3M Pak 10 Socket, PK10 series PK10-XXXSX-X-DA
Page of 8 M Pak 0 Plug, PK0 series PK0-XXXPX-X-DA M Pak 0 Socket, PK0 series PK0-XXXSX-X-DA Product Specification Revised 08-0- Page of 8 Table of Contents Title Page.............................................................................
More information3.1 Materials The housing is 316 stainless steel (excluding the connector shell which is 303 or better).
Change NO. LTR Description Author Date Approved Date 10448 A Update Standards, Change Probe Dims. JWS 6-7-12 JWS 6-7-12 10485 B Add Figure 2 for Probes Longer Than 3 Inches JWS 12-3-12 JWS 12-3-12 10497
More informationPRODUCT SPECIFICATIONS
PRODUCT SCIFICATIONS CUSTOMER : CUSTOMER'S REFERENCE : 3/34 3/35 3/36 Series DESCRIPTIONS : SHENGXIN TY : METALLIZED POLYESTER FILM CAPACITOR-BOX series Fig. w T T W H.5max P 20min H S L0.5max Fig Fig2.
More informationATC 200 A Series BX Ceramic Multilayer Capacitors
200 A Series BX Ceramic Multilayer Capacitors Case A Size Capacitance Range (.055" x.055") 5 pf to 0.01 µf Low ESR/ESL Mid-K Rugged High Reliability Construction Extended VDC Available, the industry leader,
More informationSolid Tantalum SMD Capacitors TANTAMOUNT, Hi-Rel COTS, Low ESR, Metal Case
Solid Tantalum SMD Capacitors TANTAMOUNT, Hi-Rel COTS, Low ESR, Metal Case PERFORMANCE CHARACTERISTICS Operating Temperature: -55 C to +125 C (above 85 C, voltage derating is required) Capacitance Range:
More informationMetallized PPS Capacitors for extreme capacitance stability. 1 min / 23 C B
Replaces CKM 501 B series Applications & Characteristics Railway signalling High-temperature (125 C) High capacitance stability Harmonized circuits Filtering High-reliability circuits Security applications
More informationInterference suppression film capacitors MKP 336 1
MKP RADIAL POTTED TYPE PITCH /15/22.5/27.5 mm l b h lt P d t CBA196 Fig.1 Simplified outlines. FEATURES to 27.5 mm lead pitch Supplied loose in box and taped on reel Consists of a low-inductive wound cell
More informationProduct Data Sheet PD-0053-A
Product Data Sheet PD-0053-A 3M Mini D Ribbon (MDR) Connector MDR Surface Mount 102XX-1210 XE 102XX-1S10 XE Page: 1 of 11 Table of Contents 1.0 SCOPE...2 2.0 PRODUCT TESTED...2 3.0 GENERAL CONDITIONS...2
More informationMOLEX TAIWAN LTD ( GC ) TITLE : SINGLE PORT UP-RIGHT TYPE USB CONNECTOR
SINGLE PORT UP-RIGHT TYPE USB CONNECTOR 971205 1 of 8 1.0 SCOPE This specification covers the USB series product. 2.0 APPLICABLE DOCUMENTS The following documents form a part of this specification to the
More informationPRODUCT SPECIFICATION
Page 1 Page 2 1.0 SCOPE. This specification covers performance, tests and quality requirements for the SIM Card Connector SIM 2055 (Receiver Type, 6-Pin, SMT, 1.8 & 2.2mm Profiles). 2.0 PRODUCT NAME AND
More informationAPPLICATION NOTES FOR MULTILAYER CERAMIC CAPACITORS
APPLICATION NOTES FOR MULTILAYER CERAMIC CAPITORS ELECTRICAL CHARTERISTICS The fundamental electrical properties of multilayer ceramic capacitors are as follows: Polarity: Multilayer ceramic capacitors
More informationPERFORMANCE SPECIFICATION SHEET
INCH-POUND MIL-PRF-64266/21 w/ AMENDMENT 1 1 December 2014 MIL-PRF-64266/21 6 November 2013 PERFORMANCE SPECIFICATION SHEET CONNECTORS, FIBER OPTIC, CIRCULAR, PLUG AND RECEPTACLE STYLE, MULTIPLE REMOVABLE
More informationWet Tantalum Capacitors, High Energy, Ultra High Capacitance, -55 C to +125 C Operation
Wet Tantalum Capacitors, High Energy, Ultra High Capacitance, -55 C to +125 C Operation FEATURES High energy, very high capacitance design All tantalum, hermetically sealed case Available Utilizes proven
More informationTRM Professional Multianode
Tantalum Ultra Low Capacitor FEATURES Improved reliability 0.5%/1khrs (twice better than standard) reduced by 25% to 0.0075 CV Robust against higher thermo-mechanical stresses during assembly process Multi-anode
More informationDLA LAND AND MARITIME COLUMBUS, OHIO TITLE MICROCIRCUIT, LINEAR, CMOS SPDT SWITCH, MONOLITHIC SILICON REVISIONS
REVISIONS LTR DESCRIPTION DTE PPROVED Prepared in accordance with SME Y14.24 Vendor item drawing REV PGE REV PGE REV STTUS OF PGES REV PGE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 PMIC N/ PREPRED BY RICK OFFICER
More informationTHB AC Filtering Metalized Polypropylene Film Capacitor Radial Type 85 C / 85 % RH 1000 h at U NAC
THB AC Filtering Metalized Polypropylene Film Capacitor Radial Type 85 C / 85 % RH 00 h at U NAC FEATURES High robustness under high humidity THB 85 C, 85 % RH, 00 h at rated U NAC UL 8 (electrical pending)
More informationSeries CCR-39S Multi-Throw DC-12 GHz, SP9T & SP10T Latching Coaxial Switch
PART NUMBER CCR-39S DESCRIPTION Commercial Latching Multi-throw, DC-12GHz The CCR-39Sis a broadband, multi-throw, electromechanical coaxial switch designed to switch a microwave signal from a common input
More informationProduct Specification
Product Specification NUMBER TDD2 HYBRID CAPACITOR ISSUE 01 REVISION E ECC-13-029 DATE 10-1-13 1.0 Scope This document contains specific electrical, mechanical, and environmental requirements and specifications
More information3M Pak 50 Boardmount Socket, P50 series P50-XXXS-XXX-EA. 3M Pak 50 Boardmount Plug, P50 series P50-XXXP-XXX-EA
Page of 8 3M Pak 50 Boardmount Socket, P50 series P50-XXXS-XXX-EA 3M Pak 50 Boardmount Plug, P50 series P50-XXXP-XXX-EA Product Specification 78-50-0-7 Revised 08-09- Page of 8 Table of Contents Title
More informationREVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A
REVISIONS LTR DESCRIPTION DTE (YR-MO-D) PPROVED dd paragraphs 1.5, 4.4.4.1, and 4.4.4.2 for radiation hardened requirements. Make change to Input voltage Enable (EN) maximum limit as specified under paragraph
More information7000 SERIES THUMBWHEEL SWITCHES
7000 SERIES THUMBWHEEL SWITCHES The combines heavy-duty construction and a compact package size. Designed to meet demanding military performance specifications, the switch features a unique one-piece housing
More informationRESOLVER (D/R) CONVERTERS
HIGH POWER 1-BIT digital-to- RESOLVER (D/R) CONVERTERS FEATURES Make sure the next Card you purchase has... VA Drive Capacity 8-Bit/-Byte Double Buffered Transparent Latch Resolution: 1 Bits Accuracy:
More informationMetal Case Hermetically-Sealed Metalized Polyester-Film Capacitors
Type 28P Metal Case Hermetically-Sealed Metalized Polyester-Film Capacitors EECTRICA SPECIFICATIONS Operating Temperature: -55 C to +25 C Capacitance Range: 0.00 μf to 2.0 μf Voltage Range: 00 VC to 400
More information303139, FEATURES INTRODUCTION. TABLE 1 - TOLERANCE AND TCR VS. RESISTANCE VALUE (- 55 C to C, + 25 C ref.)
303139, 303140 Models # 303139 and 303140 - Molded Surface Mount Space and Military Grade Resistors SMRxDZ with Screen/Test Flow in Compliance with EEE-INST-002, (Tables 2A and 3A, Film/Foil, Level 1)
More informationMULTILAYER CERAMIC CAPACITORS/AXIAL & RADIAL LEADED
MULTILAYER CERAMIC CAPACITORS/AXIAL & RADIAL LEADED Multilayer ceramic capacitors are available in a variety of physical sizes and configurations, including leaded devices and surface mounted chips. Leaded
More informationWet Tantalum Capacitors, High Energy, Ultra High Capacitance, -55 C to +125 C Operation
Wet Tantalum Capacitors, High Energy, Ultra High Capacitance, -55 C to +125 C Operation FEATURES High energy, very high capacitance design All tantalum, hermetically sealed case Utilizes proven SuperTan
More informationSpecifications: The shelf life of product is within 6 months. Features Description Test Conditions Requirements
Specifications: Operating Temperature Range : -25 C to+70 C Storage Temperature Range : -30 C to +80 C Current Range : 50mA, 12V DC The shelf life of product is within 6 months Test Sequence: Appearance
More informationMOTOR WIRING DATA From National Electrical Code 3 PHASE SQUIRREL CAGE INDUCTION MOTORS 230 Volt 460 Volt Min. # Max. Rating
MOTOR WIRING DATA From National Electrical Code PHASE SQUIRREL CAGE INDUCTION MOTORS 20 Volt 0 Volt Min. # Max. Rating Min. Size Size of Full Size Wire Conduit Branch Circuit Load Wire AWG (inches) Fuses
More informationSeries CCR-39S Multi-Throw DC-12 GHz, SP9T & SP10T Latching Coaxial Switch
COAX SWITCHES Series CCR-39S PART NUMBER CCR-39S DESCRIPTION Commercial Latching Multi-throw, DC-12GHz The CCR-39Sis a broadband, multi-throw, electromechanical coaxial switch designed to switch a microwave
More informationDEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO TITLE MICROCIRCUIT, DIGITAL, DUAL RETRIGGERABLE MONOSTABLE MULTIVIBRATOR, MONOLITHIC SILICON REVISIONS
REVISIONS LTR DESCRIPTION DTE PPROVED Update boilerplate to current MIL-PRF-38535 requirements. - PHN 14-06-24 Thomas M. Hess CURRENT DESIGN CTIVITY CGE CODE HS CHNGED NMES TO: DL LND ND MRITIME 43218-3990
More informationSolid Tantalum Chip Capacitors TANTAMOUNT, Low Profile, Conformal Coated, Maximum CV
Solid Tantalum Chip Capacitors TANTAMOUNT, Low Profile, Conformal Coated, Maximum CV FEATURES New case size offerings. 2mm height Terminations: Tin (2) standard. Low ESR 8mm, 12mm tape and reel packaging
More informationCERAMIC CONFORMALLY COATED/AXIAL
CERAMIC CONFORMALLY COATED/AXIAL AXIMAX & GOLD MAX GENERAL SPECIFICATIONS Working Voltage: Axial (WVDC) C0G 50, 100, 200 X7R 25, 50, 100, 200, 250 Z5U 50, 100 Radial (WVDC) C0G 50, 100, 200, 500, 1k, 1.5k,
More information5730A High Performance Multifunction Calibrator. Extended specifications
730A High Performance Multifunction Calibrator Extended specifications General Specifications Warm-Up Time... Twice the time since last warmed up, to a maximum of 30 minutes. System Installation... Rack
More informationPERFORMANCE SPECIFICATION SHEET
INCH-POUND MIL-PRF-64266/13A w/ Amendment 1 1 December 2014 SUPERSEDING MIL-PRF-64266/13A 15 October 2013 PERFORMANCE SPECIFICATION SHEET CONNECTORS, FIBER OPTIC, CIRCULAR, PLUG AND RECEPTACLE STYLE, MULTIPLE
More informationSolid Tantalum Surface Mount Chip Capacitors TANTAMOUNT, Molded Case, for Medical Instruments
Solid Tantalum Surface Mount Chip Capacitors TANTAMOUNT, Molded Case, for Medical Instruments FEATURES For non-life support medical applications High reliability Weibull grading options DC leakage at 0.005
More informationAUTOMOTIVE CURRENT TRANSDUCER OPEN LOOP TECHNOLOGY HC6H 400-S/SP1
AUTOMOTIVE CURRENT TRANSDUCER OPEN LOOP TECHNOLOGY HC6H 400-S/SP1 Picture of product with pencil Introduction The HC6H family is for the electronic measurement of DC, AC or pulsed currents in high power
More informationSeries CCR-39S Multi-Throw DC-12 GHz, SP7T & SP8T Latching Coaxial Switch
PART NUMBER CCR-39S DESCRIPTION Commercial Latching Multi-throw, DC-12GHz The CCR-39S is a broadband, multi-throw, electromechanical coaxial switch designed to switch a microwave signal from a common input
More informationDLA LAND AND MARITIME COLUMBUS, OHIO TITLE MICROCIRCUIT, LINEAR, VOLTAGE REFERENCE, MONOLITHIC SILICON
REVISIONS LTR DESCRIPTION DTE PPROVED Make change to the lead finish from -01XB to -01XE. Update document paragraphs to current requirements. - ro 17-08-15 C. SFFLE Prepared in accordance with SME Y14.24
More informationELECTROMAGNETIC OSCILLATIONS AND ALTERNATING CURRENT
Chapter 31: ELECTROMAGNETIC OSCILLATIONS AND ALTERNATING CURRENT 1 A charged capacitor and an inductor are connected in series At time t = 0 the current is zero, but the capacitor is charged If T is the
More informationKH600. 1GHz, Differential Input/Output Amplifier. Features. Description. Applications. Typical Application
KH 1GHz, Differential Input/Output Amplifier www.cadeka.com Features DC - 1GHz bandwidth Fixed 1dB (V/V) gain 1Ω (differential) inputs and outputs -7/-dBc nd/3rd HD at MHz ma output current 9V pp into
More informationMILITARY SPECIFICATION MICROCIRCUITS, DIGITAL, SCHOTTKY TTL, ARITHMETIC LOGIC UNIT / FUNCTION GENERATORS, MONOLITHIC SILICON
C OUND MI-M-38510/78 7 September 2005 SUERSED MI-M-38510/78 6 JUNE 1984 MIITRY SECIFICTION MICROCIRCUITS, DIIT, SCOTTKY TT, RITMETIC OIC UNIT / FUNCTION ENERTORS, MONOITIC SIICON This specification is
More informationUnit 11 Wire Tables and Conductor Sizes
Wire Tables and Conductor Sizes Objectives: Discuss factors that determine conductor ampacity. Discuss resistance of wire. Determine insulation characteristics. Use temperature correction factors. Determine
More informationMULTILAYER CHIP CERAMIC CAPACITOR
MULTILAYER CHIP CERAMIC CAPACITOR ( :) 1000V 1.5 50mA 5S 1000V 2000V 1.2 50mA 5S 2000V 1.2 10mA 5S DC-DC 1206 CG 100 J 202 N T (PF) ( ) 0603 0.60 0.30 1.60 0.80 0805 0.08 0.05 2.00 1.25 1206 0.12 0.06
More informationDATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS General Purpose & High Capacitance Class 2, X7R
Product Specification May 12, 17 V.18 DATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS General Purpose & High Capacitance Class 2, 6.3 V TO 50 V 100 pf to 22 µf RoHS compliant & Halogen Free Product
More informationI INCH- POUND j MIL-STD-1399(NAVY SECTION 302A 29 February 1988 SUPERSEDING DOD-STD-1399(NAVY) SECTION March 1972 (See 6.3) MILITARY STANDARD
I INCH- POUND j MIL-STD-1399(NAVY SUPERSEDING DOD-STD-1399(NAVY) SECTION 302 20 March 1972 (See 6.3) MILITARY STANDARD INTERFACE STANDARD FOR SHIPBOARD SYSTEMS SECTION 302 WEATHER ENVIRONMENT AMSC N/A
More informationSMPS STACKED CAPACITORS CATALOG 1001
SMPS STCKED CPCITORS CTLOG 01 NOTE: DSCC DRWING 876 HS BEEN CNCELLED www.dscc.dla.mil/downloads/ MilSpec/DsccDwg/876.pdf Mil-PRF-970 capacitors are preferred over DSCC-DWG-876 capacitors. The Mil-PRF-
More informationREVISIONS SYMBOL DESCRIPTION DATE APPROVAL - A
REVISIONS SYMBOL DESCRIPTION DATE APPROVAL - A B C D E F Initial Release Revised numbering scheme, separated electrical and mechanical, editorial changes throughout Corrected typographical errors in PIN
More informationELECTRO MAGNETIC INDUCTION
ELECTRO MAGNETIC INDUCTION 1) A Circular coil is placed near a current carrying conductor. The induced current is anti clock wise when the coil is, 1. Stationary 2. Moved away from the conductor 3. Moved
More informationCGS ALUMINUM ELECTROLYTIC CAPACITORS
CGS ALUMINUM ELECTROLYTIC CAPACITORS EXTREME APPLICATON HIGHLIGHTS APPLICATION Capacitance 50-500,000µF U.P.S Systems Voltage 15 to 500 WVDc Inverters/P.C.U.s. -10%, + 20% Tolerance and Motor Special Controls
More informationREVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED. A Update to current requirements. Editorial changes throughout. - gap Raymond Monnin
REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update to current requirements. Editorial changes throughout. - gap 06-10-05 Raymond Monnin Remove class M references. Update drawing to current MIL-PRF-38535
More informationMILITARY SPECIFICATION MICROCIRCUITS, DIGITAL, CMOS 4096 BIT STATIC RANDOM ACCESS MEMORY (RAM) MONOLITHIC SILICON
INCH POUND 23 JANUARY 2006 SUPERSEDING MIL-M-38510/289 4 DECEMBER 1986 MILITARY SPECIFICATION MICROCIRCUITS, DIGITAL, CMOS 4096 BIT STATIC RANDOM ACCESS MEMORY (RAM) MONOLITHIC SILICON This specification
More informationRF LOADS FIXED COAXIAL DC 22 GHz DETAIL SPECIFICATION
1/ 11 Titre / Title RF LOADS FIXED COAXIAL DC 22 GHz Rédigé par / Written by Responsabilité / Responsibility Date Signature S. POIZAT Space Project Manager Vérifié par / Verified by V. EUDELINE Space B.
More informationApplications. RoHS Compliant (6/6) according to Directive 2002/95/EC when ordered with 100% Sn solder or gold plated.
T513 Multiple Anode Low COTS MnO2 Series Overview The T513 Series is suitable for the Commercial Offthe-Shelf (COTS) requirements of industrial, telecom, defense and aerospace markets. This surface mount
More informationDEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO TITLE MICROCIRCUIT, LINEAR, PRECISION LOW DROPOUT CONTROLLER, MONOLITHIC SILICON REVISIONS
REVISIONS LTR DESCRIPTION DTE PPROVED Update the boilerplate paragraphs. - ro 09-02-19 R. HEBER B dd footnote 1/ to Table I. Update document paragraphs to current requirements. - ro 15-02-05 C. SFFLE CURRENT
More informationDIM. A (+ 0,05 0,51) .135 ±.015 (3,43 ± 0,38) COMMON LUG INTEGRAL ASSEMBLY NUT, DO NOT REMOVE 1/4-32 UNEF-2A THREAD
Multi-Deck SERIES 0 SERIES 0 0." Diameter, / Amp, Standard, Military SR FEATURES Proven Quality in Thousands of Applications Gold-plated Contact System 0,,, 0 and 0 Angle Options MIL Qualified Versions
More informationList... Package outline... Features Mechanical data... Maximum ratings... Rating and characteristic curves... Pinning information...
List List... Package outline... 1 Features... Mechanical data... Maximum ratings... Rating and characteristic curves... 3 Pinning information... 4 Marking... 4 Tube packing... 4 Suggested thermal profiles
More informationV V I H. T Part Number Marking
Phillip Havens Oct 2008 SIDCtor Protection Thyristors SDP Biased Series - 5x6 QN RoHS Pb e3 Description This new SDP Biased series provides overvoltage protection for applications such as VDSL2, DSL2,
More informationLT R1. Quad Matched Resistor Network. Applications. Typical Application
Quad Matched Resistor Network Features n Excellent Matching A-Grade: 0.0% Matching B-Grade: 0.0% Matching n 0.ppm/ C Matching Temperature Drift n ±V Operating Voltage (±0V Abs Max) n ppm/ C Absolute Resistor
More informationMetallized polyester film capacitors MKT 470
MKT RADIAL POTTED TYPE PITCH 5 mm CBA141 Fig.1 Simplified outlines. FEATURES Low-inductive wound cell of metallized (PETP) film Potted with epoxy resin in a flame-retardant case Radial leads of solder-coated
More informationProduct Specification HYCAP HIGH TEMP, EXTREME SHOCK &VIBRATION. Family >>> HCD HC2D HC3D Max mass 18g 15g 15.5g
CPCITOR HYCP HIGH TEMP, &VIBRTION DTE 3/14/16 1.0 SCOPE This document contains specific electrical, mechanical, and environmental requirements and specifications for double- sealed, axial- leaded hybrid
More informationSTANDARD MICROCIRCUIT DRAWING MICROCIRCUIT, LINEAR, PRECISION TIMER, MONOLITHIC SILICON
REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED REV REV 15 16 17 REV STATUS REV OF S 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS
More informationQualification Test Report
Qualification Test Report 501-97 28Jun10 Rev E Connector, Shielded, Miniature Circular DIN, PCB Mounted 1. INTRODUCTION 1.1. Purpose Testing was performed on Tyco Electronics Mini DIN Printed Circuit Board
More informationREVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED
REVISIONS LTR DESCRIPTION DTE (YR-MO-D) PPROVED Make corrections to figure 2 terminal connections. Pin 10, delete TMODE and replace with PG. Pin 11, delete GND and replace with TMODE. - ro 13-10-09 C.
More informationThis specification covers the requirements for product performance, test methods and quality assurance provisions of FG Terminal.
DESIGN OBJECTIVES The product described in this document has not been fully tested to ensure conformance to the requirements outlined below. Therefore AMP Ltd makes no representation or warranty, express
More informationPRODUCT SPECIFICATION
CONNECTOR CONNECTOR 1 of 6 CONNECTOR 1.0 SCOPE This Product Specification covers the dip type for 13pins slimline SATA receptacle connector. 2.0 PRODUCT DESCRIPTION 2.1 PRODUCT NAME AND SERIES NUMER(S)
More informationDATA SHEET. BGY115A; BGY115B; BGY115C/P; BGY115D UHF amplifier modules DISCRETE SEMICONDUCTORS May 13
DISCRETE SEMICONDUCTORS DATA SHEET Supersedes data of May 994 File under Discrete Semiconductors, SC9 996 May 3 FEATURES 6 V nominal supply voltage996 May 3. W output power (BGY5A, BGY5B and BGY5D).4 W
More information