HCE Series Miniature amplified pressure sensors
|
|
|
- Alexia Harvey
- 5 years ago
- Views:
Transcription
1 FEATURES 10 to 5, absolute, gage or differential pressure Barometric pressure ranges Digital SPI bus and analog output Precision ASIC signal conditioning Calibred and temperure compensed Mched pressure volumes Miniure SMD housings RoHS compliant SPECIFICATIONS Maximum rings ELECTRICAL CONNECTION Supply voltage S HCE DC HCE DC max DC current Sink 1 ma Source 1 ma Lead specificions Average preheing temperure gradient.5 K/s Soak time ca. 3 min Time above 17 C 50 s Time above 30 C 40 s Time above 50 C 15 s Peak temperure 60 C Cooling temperure gradient -3.5 K/s out s GND MISO CLK SS MOSI Temperure ranges 6 Compensed C Opering C Storage C Humidity limits (non-condensing) %RH E / 1165 / F 1/11
2 PRESSURE SENSOR CHARACTERISTICS (T A = 5 C) Part no. Opering pressure, 5 Proof pressure 3 Burst pressur e 4, 5 HCEM010...B ± HCEM00...B ± HCEM050...B ± HCEM100...B ± HCEM00...B ±00 HCEM500...B ±500 HCEB001...B ±1 3 5 HCEM010...U HCEM00...U HCEM050...U HCEM100...U HCEM00...U HCEM500...U HCEB001...U HCEB00...U HCEB005...U H CE0611AR (a) 3 5 H CE0811AR (a) 3 5 Other pressure ranges are available on request. Please contact First Sensor. Specificion notes: 1. Total accuracy is the combined error from offset and span calibrion, linearity, pressure hysteresis, and temperure effects. Linearity is the measured deviion based on a straight line. Hysteresis is the maximum output difference any point within the opering pressure range for increasing and decreasing pressure. Calibrion errors include the deviion of offset and full scale from nominal values.. Scale Span (FSS) is the algebraic difference between the output signal for the highest and lowest specified pressure. 3. Proof pressure is the maximum pressure which may be applied without causing durable shifts of the electrical parameters of the sensing element. 4. Burst pressure is the maximum pressure which may be applied without causing damage to the sensing element or leaks to the housing. 5. The HCE common mode pressure is for all devices up to 500 and 7 for all other devices. Common mode pressure is the maximum pressure th can be applied to both s of a differential pressure sensor simultaneously without damaging the sensor housing. 6. Extended temperure ranges on request. Please contact First Sensor. 7. delay time between pressure change the pressure die and signal change the output. 8. The response time depends on the adjusted internal A/D resolution of the sensor. For 14 bit it is typ. 1 ms. Other A/D resolutions and reponse times are available on request. Please contact First Sensor for further informion. 9. Sensors with lower current consumption are available on request. Please contact First Sensor for further informion. E / 1165 / F /11
3 PERFORMANCE CHARACTERISTICS ( s = 5.0, T A = 5 C, analog output signal is riometric to S, digital output signal is not riometric to S, pressure applied to high pressure ) All HCE...5 devices ( S = 5.0) s 1 Total accuracy ( C) HCE , HCE ±1. 0 %FSS all other devices ±0. 5 7, 8 Response delay 1 ms 8 A/D resolution 14 bit D/A resolution 11 9 Current consumption (no load) 5 ma HCE...R...5 (ometric devices) HCE...B...5 (bidirectional devices) D IGITAL PERFORMANC E C HARACTERISTIC S min. specified pressure C BC6 6CCC 6DD min. specified pressure HCE...U...5 (unidirectional devices) D IGITAL PERFORMANC E C HARACTERISTIC S 05E E C49 6CCC 6D4F D IGITAL PERFORMANC E C HARAC TERISTIC A1C 6666 max. specified pressure 6C49 6CCC 6D4F min. specified pressure 05E E max. specified pressure min. specified pressure E / 1165 / F 3/11
4 PERFORMANCE CHARACTERISTICS ( s = 3.0, T A = 5 C, analog output signal is riometric to S, digital output signal is not riometric to S, pressure applied to high pressure ) All HCE...3 devices ( S = 3.0) s 1 Total accuracy ( C) HCE , HCE ±1. 0 %FSS all other devices ±0. 5 7, 8 Response delay 1 ms 8 A/D resolution 14 bit D/A resolution 11 9 Current consumption (no load) 3 ma HCE...R...3 (ometric devices) HCE...B...3 (bidirectional devices) D IGITAL PERFORMANC E C HARACTERISTIC S min. specified pressure 09D0 0AAA 0B F5 5FFF 60D9 min. specified pressure HCE...U...3 (unidirectional devices) D IGITAL PERFORMANC E C HARACTERISTIC S 0A3D 0AAA 0B F9 5FFF 606C D IGITAL PERFORMANC E C HARAC TERISTIC 34E C 5555 max. specified pressure 5F9 5FFF 606C min. specified pressure 0A3D 0AAA 0B max. specified pressure min. specified pressure E / 1165 / F 4/11
5 SPI - SERIAL PERIPHERAL INTERFACE Introduction The HCE is capable to genere a digital output signal. The device runs a cyclic program, which will store a corrected sensor value with 14 bit resolution about every 500 µs within the output registers of the internal ASIC. This cyclic program runs independent from the bus communicion. In order to use the pressure sensor for digital signal readout, it should be connected to a SPI Master device. SPI specifies four signals: The clock (CLK) is genered by the master and input to all slaves. MOSI carries da from master to slave. MISO carries da from slave back to master. A slave select line (SS) allows individual selection of a slave device. SPI Modes A pair of parameters called clock polarity (CPOL) and clock phase (CPHA) determine the edges of the clock signal on which the da are driven and sampled. Each of the two parameters has two possible stes, which allows for four possible combinions, all of which are incompible with one another. In general the HCE series sups all combinions of clock phase (CPHA) and polarity (CPOL). By default it is programmed to CPHA = 0 and CPOL = 0, which means th da transmission starts with the rising first clock edge (see Fig 1). Slave select The falling edge of the SS line indices the beginning of the transfer. Additionally the SS line must not be neged and reasserted between the three bytes to be transmitted. Da operion The MOSI line should always be set to high level. So there is no da transmission from master to slave. Because of internal configurion the slave will answer the first byte with an FFxh. The second and third byte contain the 15 bit pressure informion (see Fig. ). For further informion please refer to First Sensor's SPI bus applicion note SCK cycle SCK (CPOL=0) MOSI MSB LSB MISO MSB LSB SS Sampling Fig. 1: Example of a standard 1 byte SPI da transfer for CPHA=0 and CPOL=0 MOSI MISO Da Byte 1 Da Byte Da Byte X X X X X X X X X P14 P13 P1 P11 P10 P9 P8 P7 P6 P5 P4 P3 P P1 P0 Relevant da Fig. : 3 byte da stream between HCE sensor and master containing the pressure value as a 15 bit informion E / 1165 / F 5/11
6 SPI - SERIAL PERIPHERAL INTERFACE (cont.) Interface parameters Parameter S ymbol Input high level Input low level 0 10 % of s low level 10 Pull-up resistor 500 Ω Load MISO C MIS O 400 Input each pin C SPI_IN 10 pf Signal clock frequency fs CK 100* 640 khz MISO hold time after SCK sample slope tspi_hd_mis O 00 ns MOSI setup time before SCK sample slope tspi_su_mos I / fclk / SS setup time before SCK sample slope tspi_su_s S 10 ns / SS hold time after SCK sample slope tspi_hd_s S 1/ fclk * recommended Note: First Sensor recommends communicion speeds of least 100 khz (max. 640 khz). Please contact us for further informion. SCK (CPOL=0) t SPI_SU_SS t SPI_SU_MOSI t SPI_HD_MISO t SPI_HD_SS MOSI MISO SS Fig. 3: Timing characteristics E / 1165 / F 6/11
7 PHYSICAL DIMENSIONS AND ELECTRICAL CONNECTIONS HCE...E8... SMD dual, same side, straight s Ø s GND 3 out HCE...E9... SMD dual, same side, bed s s GND 3 out Ø.0 E / 1165 / F 7/11
8 PHYSICAL DIMENSIONS AND ELECTRICAL CONNECTIONS (cont.) HCE...H8... SMD single, straight s GND 3 out Ø.00 HCE...H9... SMD single, bed s GND 3 out Ø.0 E / 1165 / F 8/11
9 PHYSICAL DIMENSIONS AND ELECTRICAL CONNECTIONS (cont.) HCE...Q8... SMD dual, opposite side, straight s HCE...Q9... SMD dual, opposite side, bed s s GND 3 out Ø s GND 3 out Ø E / 1165 / F 9/11
10 HOUSING OPTIONS Different housing options are available on request. Please contact First Sensor. Dual Inline Packages (DIP) (Sample package shown: DIP dual, same side) Single Inline Packages (SIL) (Sample package shown: SIL dual, same side) Ø E / 1165 / F Ø.00 10/11
11 ORDERING INFORMATION Options Example: Series Pressure range HCE A* Pressure mode D l M010 M00 M050 M100 M00 M500 B001 Calibrio n Housing Porting Grade oltage Absolute B B idirectional E * SMD, s, 8* Straight P Prime 3 3 Differentia U U nidirectiona l same side 9* * Barbed G G age R* 0 B arometric H* * SMD, 1 50 Q * SMD, s, 100 opposite side ( B001A) 1 a B00 B005 5 * only available for pressure ranges 0611, 0811, B001, B00 * for pressure ranges 0611, 0811 Housings Q only available up to 1. Please contact First Sensor. * standard for differential devices, "D" ** standard for absolute and gage devices, "A" and "G" * standard for devices up to 500 and ometric ranges ** standard for devices from 1 HCE M050 D B E 8 P 5 Note: Devices highlighted in grey are preferred stock items Custom specific pressure ranges and mechanical or electronic sensor modificions are widely available: I C, switching and custom specific outputs Dual inline packages (DIP) Single inline packages (SIL)... etc. Please contact First Sensor for further informion. First Sensor reserves the right to make changes to any products herein. First Sensor does not assume any liability arising out of the applicion or use of any product or circuit described herein, neither does it convey any license under its pent rights nor the rights of others. E / 1165 / F 11/11
HME Series Amplified pressure sensors
FEATURE 100 to 10, 1 to 10 psi, gage or differential pressure Increased media compatibility 1 Digital PI bus output Precision AIC signal conditioning Calibrated and temperature compensated DIP housings
HCL Series Miniature compensated low pressure sensors
FEATURES 0... 5 to 0... 5, differential or gage Calibrated and temperature compensated Matched pressure volumes Miniature SMT and SIL housings RoHS compliant SPECIFICATIONS Maximum ratings EQUIVALENT CIRCUIT
HDO Series Precision compensated pressure sensors
FEATURES to, absolute, gage or differential pressure Calibrated and temperature compensated High impedance for low power applications Sm SMD packages RoHS compliant MEDIA COMPATIBILITY To be used with
HMA Series Amplified pressure sensors
FEATURES 00 to 0 bar, to 0 psi gage or differential pressure Increased media compatibility Analog output Precision ASIC signal conditioning Calibrated and temperature compensated 2 SIL and DIP housings
LME series digital low differential pressure sensors
The LME differential low pressure sensors are based on thermal flow measurement of gas through a micro-flow channel integrated within the sensor chip. The innovative LME technology features superior sensitivity
HRO Series Precision compensated pressure sensors
Precision compensated sensors FEATURES to, O to, differential Precision temperature compensated Calibrated offset and span RoHS compliant Quality Management System according to ISO 8:00 and ISO 0:008 MEDIA
Amplified Low Pressure Sensors
Amplified Low Pressure Sensors 1 mbar (0.4 In H2O) to 60 In H2O Pressure Sensors Features 0 to 1 mbar to 0 to 60 In H2O Pressure Ranges Ratiometric 4 Output Temperature Compensated Calibrated Zero and
MS4525HRD (High Resolution Digital)
MS4525HRD (High Resolution Digital) Integrated Digital Pressure Sensor (24-bit Σ ADC) Fast Conversion Down to 1 ms Low Power, 1 µa (standby < 0.15 µa) Supply Voltage: 1.8 to 3.6V Pressure Range: 1 to 150
RCO Series Precision compensated pressure sensors
FEATURES 0...0 m to 0..., to 0, differential, gage or absolute Temperature compensated Calibrated zero and span High for low power applications Sensortechnics PRO services MEDIA COMPATIBILITY To be used
RDO Series Precision compensated pressure sensors
FEATURES 0...0 to, inch H O to 0...00, differential, gage or absolute Temperature compensated Calibrated zero and span High impedance for low power applications Sm DIP packages Sensortechnics PRO services
Differential Pressure Sensor
Differential Pressure Sensor MDP200 Series Features Pressure range up to ±500Pa with high accuracy of ±3.0% m.v. Pressure based on thermal micro-flow measurement Outstanding hysteresis and repeatability
Amplified Low Pressure Sensors
Amplified Low Pressure Sensors 1 mbar (0.4 In H2O) to 60 In H2O Pressure Sensors Features 0 to 1 mbar to 0 to 60 In H2O Pressure Ranges Ratiometric 4 Output Temperature Compensated Calibrated Zero and
SPECIFICATION. Messrs. DATE 20 June, 2013 No. V AP4, AG4 Pressure Sensor
DATE 20 June, 2013 No. Messrs. SPECIFICATION Model: AP4, AG4 Pressure Sensor Project: Distributor: Preliminary Edition rev. 1.00 This document has a possibility to be revised without notice. Reference:
MS4525HRD (High Resolution Digital) Integrated Digital Pressure Sensor (24-bit Σ ADC) Fast Conversion Down to 1 ms Low Power, 1 µa (standby < 0.15 µa)
Integrated Digital Pressure Sensor (24-bit Σ ADC) Fast Conversion Down to 1 ms Low Power, 1 µa (standby < 0.15 µa) Supply Voltage: 1.8 to 3.6V Pressure Range: 1 to 150 PSI I 2 C and SPI Interface up to
BTEL5000 / PTUL5000 Series Precision very low differential pressure transmitters
FETURES to, to differential pressure...6 or... m Precision temperature compensated and calibrated Rugged aluminium housing Female /8" BSP and /8" NPT fittings MEDI CMPTIBILITY Pressure inlet: Non-corrosive,
BLC Series - Basic Compact Pressure Sensor Series. Introduction
Sensors CoBeam TM Technology. The device provides a high output Features & Applications... signal at a low operating voltage and reduces the overall supply Standard Pressure Ranges... voltage while maintaining
Low Pressure Sensor Amplified Analog Output SM6295-BCM-S
Low Pressure Sensor Amplified Analog Output SM6295-BCM-S-040-000 FEATURES Pressure range from 0 to 40 cmh 2 O 5.0 V operation Amplified analog output (10 to 90%Vdd) Compensated temperature range: 0 to
BTE5000 / PTE5000 / PTU5000 Series Precision differential pressure transmitters
FEATURES 5 mbar to 0 bar, 0. to 50 psi differential pressure...6 or...0 ma Precision temperature compensated and calibrated Rugged aluminium housing Female /8" BSP and /8" NPT fittings MEDIA COMPATIBILITY
PART TEMP RANGE PIN-PACKAGE
9-0850; Rev 4; 6/0 Ω μ INT INT μ PART TEMP RANGE PIN-PACKAGE MAX7359ETG+ -40 C to +85 C 24 TQFN-EP* MAX7359EWA+ -40 C to +85 C 25 WLP * TOP VIEW AD0 GND IC COL0 8 7 6 5 4 3 INPUT +62V TO +36V V CC MAX7359
AWM3000 Series Mass flow sensor for gases
FEATURES Ranges 0...30 to 0...±1000 1 or 0...0. to 0... "H O (0... to 0... mbar).. V,..3.7 V, 4...0 ma output Actual mass flow sensing Low differential pressure sensing SERVICE To be used with dry gases
ADVANCED INFORMATION MS4525HRD (High Resolution Digital)
Integrated Digital Pressure Sensor (24-bit Σ ADC) Fast Conversion Down to 1 ms Low Power, 1 µa (standby < 0.15 µa) Supply Voltage: 1.8 to 3.6V Pressure Range: 1 to 150 PSI I 2 C and SPI Interface up to
Millivolt Output Pressure Sensors
Millivolt Output Pressure Sensors H-Grade Pressure Sensors Features 0 to 4 H2O to 0 to 100 Pressure Ranges % linearity...high accuracy version Temperature Compensated Calibrated Zero and Span General Description
Low Voltage 2-1 Mux, Level Translator ADG3232
Low Voltage 2-1 Mux, Level Translator ADG3232 FEATURES Operates from 1.65 V to 3.6 V Supply Rails Unidirectional Signal Path, Bidirectional Level Translation Tiny 8-Lead SOT-23 Package Short Circuit Protection
NTE74HC299 Integrated Circuit TTL High Speed CMOS, 8 Bit Universal Shift Register with 3 State Output
NTE74HC299 Integrated Circuit TTL High Speed CMOS, 8 Bit Universal Shift Register with 3 State Output Description: The NTE74HC299 is an 8 bit shift/storage register with three state bus interface capability
LV5217GP. Specifications. Bi-CMOS IC 3ch LED Driver. Absolute Maximum Ratings at Ta = 25 C. Ordering number : ENA0833A.
Ordering number : ENA0833A LV5217GP Bi-CMOS IC 3ch LED Driver Overview This LV5217GP is 3-channel LED driver for cell phones. Each LED driver current can be adjusted by I2C bus. LV5217GP can perform various
SX Series Pressure sensors
FEATURES 0...1 to 0...150 Absolute, differential and gage devices High impedance bridge Low power consumption for battery operation APPLICATIONS Industrial controls Pneumatic controls Medical instrumentation
NTE40194B Integrated Circuit CMOS, 4 Bit Bidirectional Universal Shift Register
NTE4194B Integrated Circuit CMOS, 4Bit Bidirectional Universal Shift Register Description: The NTE4194B is a universal shift register in a 16Lead DIP type package featuring parallel inputs, parallel outputs
SERIALLY PROGRAMMABLE CLOCK SOURCE. Features
DATASHEET ICS307-03 Description The ICS307-03 is a dynamic, serially programmable clock source which is flexible and takes up minimal board space. Output frequencies are programmed via a 3-wire SPI port.
DM74S373 DM74S374 3-STATE Octal D-Type Transparent Latches and Edge-Triggered Flip-Flops
3-STATE Octal D-Type Transparent Latches and Edge-Triggered Flip-Flops General Description These 8-bit registers feature totem-pole 3-STATE outputs designed specifically for driving highly-capacitive or
NTE4035B Integrated Circuit CMOS, 4 Bit Parallel In/Parallel Out Shift Register
NTE4035B Integrated Circuit CMOS, 4 Bit Parallel In/Parallel Out Shift Register Description: The NTE4035B is a 4 bit shift register in a 16 Lead DIP type package constructed with MOS P Channel an N Channel
Small Gage Pressure Sensor
Small Gage Pressure Sensor FEATURES Improved stability with integrated field shields Small SO8 surface-mount package 90 millivolt output Constant current or constant voltage drive Ported configuration
I2 C Compatible Digital Potentiometers AD5241/AD5242
a Preliminary Technical ata FEATURES Position Potentiometer Replacement 0K, 00K, M, Ohm Internal Power ON Mid-Scale Preset +. to +.V Single-Supply; ±.V ual-supply Operation I C Compatible Interface APPLICATIONS
74LVC574A Octal D-type flip-flop with 5-volt tolerant inputs/outputs; positive edge-trigger (3-State)
INTEGRATED CIRCUITS inputs/outputs; positive edge-trigger (3-State) 1998 Jul 29 FEATURES 5-volt tolerant inputs/outputs, for interfacing with 5-volt logic Supply voltage range of 2.7 to 3.6 Complies with
4-PIN PHOTOTRANSISTOR OPTOCOUPLERS
PACKAGE HAA84 SCHEMATIC 4 COLLECTOR 4 2 3 EMITTER DESCRIPTION The HAA84 Series consists of two gallium arsenide infrared emitting diodes, connected in inverse parallel, driving a single silicon phototransistor
Small Absolute Pressure Sensor
Small Absolute Pressure Sensor SM5420E Series FEATURES Improved stability with integrated field shields Small SO8 surface-mount package 95 millivolt span Constant current or constant voltage drive or non-ported
PI4GTL bit bidirectional low voltage translator
Features 2-bit bidirectional translator Less than 1.5 ns maximum propagation delay to accommodate Standard mode and Fast mode I2Cbus devices and multiple masters Allows voltage level translation between
8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash. ATtiny25 ATtiny25V. Appendix B. Appendix B ATtiny25/V Specification at +125 C
Appendix B ATtiny25/ Specification at +125 C This document contains information specific to devices operating at temperatures up to 125 C. Only deviations are covered in this appendix, all other information
Small, Gauge Pressure Sensor
Small, Gauge Pressure Sensor SM5G-GG Series FEATURES Improved stability with integrated field shields Small SO8 surface-mount package 90 millivolt output Constant current or constant voltage drive Ported
9-Channel 64steps Constant-Current LED Driver with SPI Control. Features
BCT3119 with SPI Control General Description The BCT3119 is a constant current driver incorporating shift register and data latch. This CMOS device is designed for LED display applications. The max output
74LVC823A 9-bit D-type flip-flop with 5-volt tolerant inputs/outputs; positive-edge trigger (3-State)
INTEGRATED CIRCUITS inputs/outputs; positive-edge trigger (3-State) 1998 Sep 24 FEATURES 5-volt tolerant inputs/outputs, for interfacing with 5-volt logic Supply voltage range of 2.7V to 3.6V Complies
UNISONIC TECHNOLOGIES CO., LTD L16B45 Preliminary CMOS IC
UNISONIC TECHNOLOGIES CO., LTD L16B45 Preliminary CMOS IC 16-BIT CONSTANT CURRENT LED SINK DRIVER DESCRIPTION The UTC L16B45 is designed for LED displays. UTC L16B45 contains a serial buffer and data latches
MM74C150 MM82C19 16-Line to 1-Line Multiplexer 3-STATE 16-Line to 1-Line Multiplexer
MM74C150 MM82C19 16-Line to 1-Line Multiplexer 3-STATE 16-Line to 1-Line Multiplexer General Description The MM74C150 and MM82C19 multiplex 16 digital lines to 1 output. A 4-bit address code determines
4-PIN PHOTOTRANSISTOR OPTOCOUPLERS
PACKAGE HAA84 SCHEMATIC 4 COLLECTOR 4 2 3 EMITTER DESCRIPTION The HAA84 Series consists of two gallium arsenide infrared emitting diodes, connected in inverse parallel, driving a single silicon phototransistor
INT RST TEMP RANGE PIN- PACKAGE TOP MARK PKG CODE PART. -40 C to +125 C -40 C to +125 C 16 QSOP E16-4 MAX7323AEE+ 16 TQFN-EP* 3mm x 3mm MAX7323ATE+
19-3806; Rev 1; 7/07 INT RST Ω μ PART MAX7323AEE+ MAX7323ATE+ * TEMP RANGE -40 C to +125 C -40 C to +125 C PIN- PACKAGE TOP MARK PKG CODE 16 QSOP E16-4 16 TQFN-EP* 3mm x 3mm ADE T1633-4 PART INPUTS INTERRUPT
NTE74HC165 Integrated Circuit TTL High Speed CMOS, 8 Bit Parallel In/Serial Out Shift Register
NTE74HC165 Integrated Circuit TTL High Speed CMOS, 8 Bit Parallel In/Serial Out Shift Register Description: The NTE74HC165 is an 8 bit parallel in/serial out shift register in a 16 Lead DIP type package
NTE74177 Integrated Circuit TTL 35Mhz Presettable Binary Counter/Latch
NTE74177 Integrated Circuit TTL 35Mhz Presettable Binary Counter/Latch Description: The NTE74177 is a high speed monolithic counter in a 14 Lead plastic DIP type package consisting of four DC coupled master
5-V Low Drop Fixed Voltage Regulator TLE 4279
5-V Low Drop Fixed Voltage Regulator TLE 4279 Features Output voltage tolerance ±2% 15 ma current capability Very low current consumption Early warning Reset output low down to V Q = 1 V Overtemperature
NTE74HC109 Integrated Circuit TTL High Speed CMOS, Dual J K Positive Edge Triggered Flip Flop w/set & Reset
NTE74HC109 Integrated Circuit TTL High Speed CMOS, Dual J K Positive Edge Triggered Flip Flop w/set & Reset Description: The NTE74HC109 is a dual J K flip flip with set and reset in a 16 Lead plastic DIP
5-V Low Drop Fixed Voltage Regulator TLE 4275
5-V Low Drop Fixed Voltage Regulator TLE 4275 Features Output voltage 5 V ± 2% Very low current consumption Power-on and undervoltage reset Reset low down to V Q = 1 V Very low-drop voltage Short-circuit-proof
DM74LS373 DM74LS374 3-STATE Octal D-Type Transparent Latches and Edge-Triggered Flip-Flops
DM74LS373 DM74LS374 3-STATE Octal D-Type Transparent Latches and Edge-Triggered Flip-Flops General Description These 8-bit registers feature totem-pole 3-STATE outputs designed specifically for driving
NTE74176 Integrated Circuit TTL 35Mhz Presettable Decade Counter/Latch
NTE74176 Integrated Circuit TTL 35Mhz Presettable Decade Counter/Latch Description: The NTE74176 is a high speed monolithic counter in a 14 Lead plastic DIP type package consisting of four DC coupled master
PRODUCT OVERVIEW REF. IN 16 BIPOLAR OFFSET 17 REGISTER 74LS75 REGISTER 74LS75 BITS LSB
FEATURES -Bit resolution Integral nonlinearity error ±/LSB, max. Differential nonlinearity error ±/LSB, max. MIL-STD- high-reliability versions available Input register μs fast output settling time Guaranteed
DATA SHEET. Thermocouple module with digital I²C-Interface - THMOD-I²C. Characteristic features. Areas of application. Features.
Description Characteristic features Industrial temperature measuring method Wide measuring range, -270...+1360 C Digital I²C-interface Simple integration to micro-controller Scope of supply with thermocouple,
LE Ω SECOND SOURCE BLEED RESISTORS PART. Maxim Integrated Products 1 MAX4800A MAX4802A. TQFP 7mm x 7mm ; Rev 0; 5/08 N.C. (RGND) TOP VIEW GND
19-4120; Rev 0; 5/08 Ω Ω μ TOP VIEW DIN VDD GND (RGND) VNN 36 35 34 33 32 31 30 29 28 27 26 25 PART BED RESISTORS SECOND SOURCE PIN- PACKAGE CXZ+* No 26 CSBGA CQI+ No HV2203PJ-G 28 PLCC CCM+* No HV2203FG-G
S-4670A. 128-bit THERMAL HEAD DRIVER FEATURES BLOCK DIAGRAM. Rev. 1.1
Rev. 1.1 128-bit THERMAL HEAD DRIVER S-4670A The S-4670A is a CMOS thermal head driver containing 128-bit (64 x 2) shift registers and latches. High speed operation at 16 MHz clock frequency together with
NTE74HC173 Integrated Circuit TTL High Speed CMOS, 4 Bit D Type Flip Flop with 3 State Outputs
NTE74HC173 Integrated Circuit TTL High Speed CMOS, 4 Bit D Type Flip Flop with 3 State Outputs Description: The NTE74HC173 is an high speed 3 State Quad D Type Flip Flop in a 16 Lead DIP type package that
ATS177. General Description. Features. Applications. Ordering Information SINGLE OUTPUT HALL EFFECT LATCH ATS177 - P L - X - X
Features General Description 3.5V to 20V DC operation voltage Temperature compensation Wide operating voltage range Open-Collector pre-driver 25mA maximum sinking output current Reverse polarity protection
Dual Low Dropout Voltage Regulator
Dual Low Dropout Voltage Regulator TLE 4473 GV55-2 Features Stand-by output 190 ma; 5 V ± 2% Main output: 300 ma, 5 V tracked to the stand-by output Low quiescent current consumption Disable function separately
ATS276 X - P X - B - X. Lead Free L : Lead Free G : Green
Features General Description On-Chip Hall Sensor with Two Different Sensitivity and Hysteresis Settings for ATS276 3.5V to 2V Operating Voltage 4mA (avg.) Output Sink Current Built-in Protecting Diode
MM74C85 4-Bit Magnitude Comparator
4-Bit Magnitude Comparator General Description The MM74C85 is a four-bit magnitude comparator which will perform comparison of straight binary or BCD codes. The circuit consists of eight comparing inputs
NJU BIT PARALLEL TO SERIAL CONVERTER PRELIMINARY PACKAGE OUTLINE GENERAL DESCRIPTION PIN CONFIGURATION FEATURES BLOCK DIAGRAM
PRELIMINARY 11-BIT PARALLEL TO SERIAL CONVERTER GENERAL DESCRIPTION The NJU3754 is an 11-bit parallel to serial converter especially applying to MCU input port expander. It can operate from 2.7V to 5.5V.
54AC174/54ACT174 Hex D Flip-Flop with Master Reset
54AC174/54ACT174 Hex D Flip-Flop with Master Reset General Description The AC/ ACT174 is a high-speed hex D flip-flop. The device is used primarily as a 6-bit edge-triggered storage register. The information
3.3 V 64K X 16 CMOS SRAM
September 2006 Advance Information AS7C31026C 3.3 V 64K X 16 CMOS SRAM Features Industrial (-40 o to 85 o C) temperature Organization: 65,536 words 16 bits Center power and ground pins for low noise High
NTE4501 Integrated Circuit CMOS, Dual 4 Input NAND Gate, 2 Input NOR/OR Gate, 8 Input AND/NAND Gate
NTE4501 Integrated Circuit CMOS, Dual 4 Input NAND Gate, 2 Input NOR/OR Gate, 8 Input AND/NAND Gate Description: The NTE4501 is a triple gate device in a 16 Lead DIP type package constructed with MOS P
onlinecomponents.com
54AC299 54ACT299 8-Input Universal Shift/Storage Register with Common Parallel I/O Pins General Description The AC/ ACT299 is an 8-bit universal shift/storage register with TRI-STATE outputs. Four modes
Low Drop Voltage Regulator TLE 4295
Low Drop Voltage Regulator TLE 4295 Features Four versions: 2.6 V, 3.0 V, 3.3 V, 5.0 V tolerance ±4% Very low drop voltage Output current: 30 ma Power fail output Low quiescent current consumption Wide
DS 300. Electronic Pressure Switch. with IO-Link interface. Stainless Steel Sensor. accuracy according to IEC 60770: 0.35 % FSO.
DS 00 Electronic Pressure Switch with IO-Link interface Stainless Steel Sensor accuracy according to IEC 60770: 0.5 % FSO Nominal pressure from 0... 00 mbar up to 0... 600 bar Digital output signal IO-Link
INTEGRATED CIRCUITS. PCK2002P 533 MHz PCI-X clock buffer. Product data Supersedes data of 2001 May Dec 13. Philips Semiconductors
INTEGRATED CIRCUITS Supersedes data of 2001 May 09 2002 Dec 13 Philips Semiconductors FEATURES General purpose and PCI-X 1:4 clock buffer 8-pin TSSOP package See PCK2001 for 48-pin 1:18 buffer part See
HIGH SPEED-10 MBit/s LOGIC GATE OPTOCOUPLERS
DESCRIPTION The / optocouplers consist of an AlGaAS LED, optically coupled to a very high speed integrated photo-detector logic gate with a strobable output. The devices are housed in a compact small-outline
MS BA01 PTH Fusion Sensor
PRELIMINARY MS8607-02BA01 PTH Fusion Sensor Integrated pressure, temperature and humidity sensor QFN package 5 x 3 x 1 mm 3 Operating range: 10 to 2000 mbar, 0%RH to 100%RH, -40 to 85 C High-resolution
SDT800-STR. Description. Features. Agency Approvals. Applications. Absolute Maximum Ratings. Schematic Diagram. Ordering Information
Description The consists of two phototransistors, each optically coupled to a light emitting diode for DC input operation. Optical coupling between the input IR LED and output phototransistor allows for
5-V Low Drop Voltage Regulator TLE 4290
5-V Low Drop Voltage Regulator TLE 429 Features Output voltage 5 V ± 2% Very low current consumption 45 ma current capability Power Good Feature Very low-drop voltage Short-circuit-proof Reverse polarity
,- # (%& ( = 0,% % <,( #, $ <<,( > 0,% #% ( - + % ,'3-% & '% #% <,( #, $ <<,(,9 (% +('$ %(- $'$ & " ( (- +' $%(& 2,#. = '%% ($ (- +' $ '%("
FEATURES!" #$$ % %&' % '( $ %( )$*++$ '(% $ *++$ %(%,- *(% (./ *( #'% # *( 0% ( *( % #$$ *( '( + 2' %( $ '( 2! '3 ((&!( *( 4 '3.%" / '3 3.% 7" 28" 9' 9,*: $ 9,*: $% (+'( / *(.( # ( 2(- %3 # $((% # ;' '3$-,(
Standard Products UT54ACS74/UT54ACTS74 Dual D Flip-Flops with Clear & Preset. Datasheet November 2010
Standard Products UT54ACS74/UT54ACTS74 Dual D Flip-Flops with Clear & Preset Datasheet November 2010 www.aeroflex.com/logic FEATURES 1.2μ CMOS - Latchup immune High speed Low power consumption Single 5
74ACT825 8-Bit D-Type Flip-Flop
8-Bit D-Type Flip-Flop General Description The ACT825 is an 8-bit buffered register. They have Clock Enable and Clear features which are ideal for parity bus interfacing in high performance microprogramming
TC4013BP,TC4013BF,TC4013BFN
TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC4013BP,TC4013BF,TC4013BFN TC4013B Dual D-Type Flip Flop TC4013B contains two independent circuits of D type flip-flop. The input level applied
MS BA01. PHT Combination Sensor SPECIFICATIONS
SPECIFICATIONS Integrated pressure, humidity and temperature sensor QFN package 5 x 3 x 1 mm 3 Operating range: 10 to 2000 mbar, 0%RH to 100%RH, -40 to 85 C High-resolution module: 0.016 mbar, 0.04%RH,
MC1403, B. Low Voltage Reference PRECISION LOW VOLTAGE REFERENCE
Low Voltage Reference A precision bandgap voltage reference designed for critical instrumentation and D/A converter applications. This unit is designed to work with D/A converters, up to bits in accuracy,
74LCX16374 Low Voltage 16-Bit D-Type Flip-Flop with 5V Tolerant Inputs and Outputs
74LCX16374 Low oltage 16-Bit D-Type Flip-Flop with 5 Tolerant Inputs and Outputs General Description The LCX16374 contains sixteen non-inverting D-type flip-flops with 3-STATE outputs and is intended for
Standard Products UT54ACS109/UT54ACTS109 Dual J-K Flip-Flops. Datasheet November 2010
Standard Products UT54ACS109/UT54ACTS109 Dual J-K Flip-Flops Datasheet November 2010 www.aeroflex.com/logic FEATURES 1.2μ CMOS - Latchup immune High speed Low power consumption Single 5 volt supply Available
TEA6422 BUS-CONTROLLED AUDIO MATRIX
BUS-CONTROLLED AUDIO MATRIX 6 Stereo Inputs 3 Stereo Ouputs Gain Control db/mute for each Output Cascadable ( different addresses) Serial Bus Controlled Very Low Noise Very Low Distorsion Fully ESD Protected
Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. DS0026 Dual High-Speed MOS Driver General Description DS0026 is a low cost
MS BA Altimeter and diving pressure sensor
MS5803-07BA Altimeter and diving pressure sensor Excellent accuracy for both altimeter and diving applications until 70m depth Operating range: 0 to 7 bar, -20 to +85 C High resolution module, 0.4m air
UT54ACTQ16374 RadHard CMOS 16-bit D Flip-Flop TTL Inputs, and Three-State Outputs Datasheet
Standard Products UT54ACTQ16374 RadHard CMOS 16-bit D Flip-Flop TTL Inputs, and Three-State Outputs Datasheet May 16, 212 www.aeroflex.com/radhard FEATURES 16 non-inverting D flip-flops with three-state
5-V Low Drop Fixed Voltage Regulator TLE
5-V Low Drop Fixed Voltage Regulator TLE 427-2 Features Output voltage tolerance ±2% 65 ma output current capability Low-drop voltage Reset functionality Adjustable reset time Suitable for use in automotive
MM74C90 MM74C93 4-Bit Decade Counter 4-Bit Binary Counter
4-Bit Decade Counter 4-Bit Binary Counter General Description The MM74C90 decade counter and the MM74C93 binary counter and complementary MOS (CMOS) integrated circuits constructed with N- and P-channel
INTEGRATED CIRCUITS. 74F521 8-bit identity comparator. Product specification May 15. IC15 Data Handbook
INTEGRATED CIRCUITS 1990 May IC Data Handbook FEATURES Compares two 8-bit words in 6.5ns typical Expandable to any word length DESCRIPTION The is an expandable 8-bit comparator. It compares two words of
UNISONIC TECHNOLOGIES CO., LTD U74HC164
UNISONIC TECHNOLOGIES CO., LTD 8-BIT SERIAL-IN AND PARALLEL-OUT SHIFT REGISTER DIP-14 DESCRIPTION The is an 8-bit edge-triggered shift registers with serial input and parallel output. A LOW-to-HIGH transition
3.3V Power Supply Isolated Current Sensor with Common Mode Field Rejection
Fully Integrated Current Sensor IC 3.3V Power Supply Isolated Current Sensor with Common Mode Field Rejection Description The Senko Micro s provides economical and precise solutions for AC or DC current
Optocoupler, Phototransistor Output, with Base Connection
Vishay Semiconductors Optocoupler, Phototransistor Output, FEATURES A 6 B Isolation test voltage 5300 V RMS Interfaces with common logic families C NC 2 3 V D E 5 4 C E Input-output coupling capacitance
Low Drop Voltage Regulator TLE
Low Drop Voltage Regulator TLE 4296-2 Features Two versions: 3.3 V, 5.0 V Output voltage tolerance ±4% Very low drop voltage Output current: 30 ma Inhibit input Low quiescent current consumption Wide operation
FPF1007-FPF1009 IntelliMAX Advanced Load Products
FPF07-FPF09 IntelliMAX Advanced Load Products Features 1.2 to 5.5 V Input Voltage Range Typical R ON = 30 mω at = 5.5 V Typical R ON = 40 mω at = 3.3 V Fixed Three Different Turn-on Rise Time µs / 80 µs
MM74C00 MM74C02 MM74C04 Quad 2-Input NAND Gate Quad 2-Input NOR Gate Hex Inverter
MM74C00 MM74C02 MM74C04 Quad 2-Input NAND Gate Quad 2-Input NOR Gate Hex Inverter General Description The MM74C00, MM74C02, and MM74C04 logic gates employ complementary MOS (CMOS) to achieve wide power
DS0026 Dual High-Speed MOS Driver
Dual High-Speed MOS Driver General Description DS0026 is a low cost monolithic high speed two phase MOS clock driver and interface circuit. Unique circuit design provides both very high speed operation
MM74C00 MM74C02 MM74C04 Quad 2-Input NAND Gate Quad 2-Input NOR Gate Hex Inverter
MM74C00 MM74C02 MM74C04 Quad 2-Input NAND Gate Quad 2-Input NOR Gate Hex Inverter General Description The MM74C00, MM74C02, and MM74C04 logic gates employ complementary MOS (CMOS) to achieve wide power
74LCXH Low Voltage 16-Bit D-Type Flip-Flop with Bushold and 26Ω Series Resistors in Outputs
February 2001 Revised October 2001 74LCXH162374 Low oltage 16-Bit D-Type Flip-Flop with Bushold and 26Ω Series Resistors in Outputs General Description The LCXH162374 contains sixteen non-inverting D-type
MS BA Miniature 14 bar Module
High resolution module, 0.2 mbar Fast conversion down to ms Low power, µa (standby < 0.5 µa) Integrated digital pressure sensor (24 bit ΔΣ AC) Supply voltage.8 to 3.6 V Operating range: 0 to 4 bar, -40
HCF4035B 4 STAGE PARALLEL IN/PARALLEL OUT SHIFT REGISTER
4 STAGE PARALLEL IN/PARALLEL OUT SHIFT REGISTER 4 STAGE CLOCKED SHIFT OPERATION SYNCHRONOUS PARALLEL ENTRY ON ALL 4 STAGES JK INPUTS ON FIRST STAGE ASYNCHRONOUS TRUE/COMPLEMENT CONTROL ON ALL OUTPUTS STATIC
MS BA01 Variometer Module, with LCP cap
High resolution module, 10 cm Fast conversion down to 1 ms Low power, 1 µa (standby < 0.15 µa) QFN package 5.0 x 3.0 x 1.7 mm 3 Supply voltage 1.8 to 3.6 V Integrated digital pressure sensor (24 bit ΔΣ
54AC258 54ACT258 Quad 2-Input Multiplexer with TRI-STATE Outputs
54AC258 54ACT258 Quad 2-Input Multiplexer with TRI-STATE Outputs General Description The AC/ ACT258 is a quad 2-input multiplexer with TRI-STATE outputs. Four bits of data from two sources can be selected