MC10EL35, MC100EL35. 5V ECL JK Flip Flop

Transcription

1 M0E35, M00E35 5V E JK Flip Flop escription The M0E/00E35 is a high speed JK flip-flop. The J/K data enters the master portion of the flip-flop when the clock is OW and is transferred to the slave, and thus the outputs, upon a positive transition of the clock. The reset pin is asynchronous and is activated with a logic IG. The 00 Series contains temperature compensation. Features 525 ps Propagation elay 2.2G z Toggle Frequency ES Protection: > kv uman Body Model, > 00 V Machine Model PE Mode Operating Range: V = 4.2 V to 5.7 with V EE = 0 V NE Mode Operating Range: V = 0 V with V EE = 4.2 V to 5.7 V Internal Input Pulldown Resistors on J, K, K, and R Meets or Exceeds JEE Spec EI/JES7 I atchup Test Moisture Sensitivity evel For dditional Information, see pplication Note N003/ Flammability Rating: U 94 V 0.25 in, Oxygen Index 2 to 34 Transistor ount = devices Pb Free Packages are vailable SOI SUFFIX SE 75 TSSOP T SUFFIX SE 94R FN MN SUFFIX SE 506 MRKING IGRMS* E35 YW 35 YW 4W M 4 KE35 YW K35 YW 2 M 4 = M0 = Wafer ot K = M00 Y = Year 4W = M0 W = Work Week 2 = M00 M = ate ode = ssembly ocation = Pb Free Package (Note: Microdot may be in either location) *For additional marking information, refer to pplication Note N002/. ORERING INFORMTION See detailed ordering and shipping information in the package dimensions section on page 5 of this data sheet. Semiconductor omponents Industries,, 200 ugust, 200 Rev. 7 Publication Order Number: M0E35/

2 M0E35, M00E35 J J V K 2 K 7 Q K 3 6 Q R R 4 5 V EE Figure. ogic iagram and Pinout ssignment Table. PIN ESRIPTION J K R K PIN E Input E Input E Reset E lock Input Q, Q E ata Outputs V V EE EP Positive Supply Negative Supply FUNTION (FN only) Thermal exposed pad must be connected to a sufficient thermal conduit. Electrically connect to the most negative supply (GN) or leave unconnected, floating open. Table. TRUT TBE J* K* R* K Qn+ X X Z Z Z Z X Qn Qn Table 2. MXIMUM RTINGS Symbol Parameter ondition ondition 2 Rating Unit V PE Mode Power Supply V EE = 0 V V V EE NE Mode Power Supply V = 0 V V V I PE Mode Input Voltage NE Mode Input Voltage V EE = 0 V V = 0 V I out Output urrent ontinuous Surge V I V 6 V I V EE 6 T Operating Temperature Range 40 to +5 T stg Storage Temperature Range 65 to +50 J Thermal Resistance (Junction to mbient) 0 lfpm 500 lfpm SOI SOI J Thermal Resistance (Junction to ase) Standard Board SOI 4 to 44 /W J Thermal Resistance (Junction to mbient) 0 lfpm 500 lfpm TSSOP TSSOP J Thermal Resistance (Junction to ase) Standard Board TSSOP 4 to 44 ± 5% /W J Thermal Resistance (Junction to mbient) 0 lfpm 500 lfpm FN FN V V m m /W /W /W /W /W /W T sol Wave Solder Pb Pb Free <2 to 3 24 <2 to J Thermal Resistance (Junction to ase) (Note ) FN 35 to 40 /W Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating onditions is not implied. Extended exposure to stresses above the Recommended Operating onditions may affect device reliability.. JEE standard multilayer board 2S2P (2 signal, 2 power) 2

3 M0E35, M00E35 Table 3. 0E SERIES PE RTERISTIS V = 5.0 V; V EE = 0 V (Note 2) Symbol haracteristic Min Typ Max Min Typ Max Min Typ Max Unit I EE Power Supply urrent m V O Output IG Voltage (Note 3) mv V O Output OW Voltage (Note 3) mv V I Input IG Voltage mv V I Input OW Voltage mv I I Input IG urrent I I Input OW urrent NOTE: evice will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit operating temperature range. Functional operation of the device exceeding these conditions is not implied. evice specification limit 2. Input and output parameters vary : with V. V EE can vary V / 0.5 V. 3. Outputs are terminated through a 50 resistor to V 2.0 V. Table 4. 0E SERIES NE RTERISTIS V = 0 V; V EE = 5.0 V (Note 4) Symbol haracteristic Min Typ Max Min Typ Max Min Typ Max Unit I EE Power Supply urrent m V O Output IG Voltage (Note 5) mv V O Output OW Voltage (Note 5) mv V I Input IG Voltage mv V I Input OW Voltage mv I I Input IG urrent I I Input OW urrent NOTE: evice will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit operating temperature range. Functional operation of the device exceeding these conditions is not implied. evice specification limit 4. Input and output parameters vary : with V. V EE can vary V / 0.5 V. 5. Outputs are terminated through a 50 resistor to V 2.0 V. Table 5. 00E SERIES PE RTERISTIS V = 5.0 V; V EE = 0 V (Note 6) Symbol haracteristic Min Typ Max Min Typ Max Min Typ Max Unit I EE Power Supply urrent m V O Output IG Voltage (Note 7) mv V O Output OW Voltage (Note 7) mv V I Input IG Voltage (Single Ended) mv V I Input OW Voltage (Single Ended) mv I I Input IG urrent I I Input OW urrent NOTE: evice will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit operating temperature range. Functional operation of the device exceeding these conditions is not implied. evice specification limit 6. Input and output parameters vary : with V. V EE can vary +0. V / 0.5 V. 7. Outputs are terminated through a 50 resistor to V 2.0 V. 3

4 M0E35, M00E35 Table 6. 00E SERIES NE RTERISTIS V = 0 V; V EE = 5.0 V (Note ) Symbol haracteristic Min Typ Max Min Typ Max Min Typ Max Unit I EE Power Supply urrent m V O Output IG Voltage (Note 9) mv V O Output OW Voltage (Note 9) mv V I Input IG Voltage (Single Ended) mv V I Input OW Voltage (Single Ended) mv I I Input IG urrent I I Input OW urrent NOTE: evice will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit operating temperature range. Functional operation of the device exceeding these conditions is not implied. evice specification limit. Input and output parameters vary : with V. V EE can vary +0. V / 0.5 V. 9. Outputs are terminated through a 50 resistor to V 2.0 V. Table 7. RTERISTIS V = 5.0 V; V EE = 0 V or V = 0 V; V EE = 5.0 V (Note 0) Symbol haracteristic Min Typ Max Min Typ Max Min Typ Max Unit f max Maximum Toggle Frequency Gz t P Propagation elay K t P to Output MR ps t S Setup Time J, K ps t old Time J, K ps t RR Reset Recovery ps t PW Minimum Pulse Width K, Reset ps t JITTER ycle to ycle Jitter ps t r t f Output Rise/Fall Times Q (20% 0%) ps NOTE: evice will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit operating temperature range. Functional operation of the device exceeding these conditions is not implied. evice specification limit 0.0 Series: V EE can vary V / 0.5 V. 00 Series: V EE can vary +0. V / 0.5 V. Q Z o = 50 river evice Receiver evice Q Z o = V TT V TT = V 3.0 V Figure 2. Typical Termination for Output river and evice Evaluation (See pplication Note N020/ Termination of E ogic evices.) 4

5 M0E35, M00E35 ORERING INFORMTION evice Package Shipping M0E35 SOI 9 Units / Rail M0E35G SOI 9 Units / Rail M0E35R2 SOI 2500 / Tape & Reel M0E35R2G SOI 2500 / Tape & Reel M0E35T TSSOP 00 Units / Rail M0E35TG TSSOP 00 Units / Rail M0E35TR2 TSSOP 2500 / Tape & Reel M0E35TR2G TSSOP 2500 / Tape & Reel M0E35MNR4 FN 000 / Tape & Reel M0E35MNR4G FN 000 / Tape & Reel M00E35 SOI 9 Units / Rail M00E35G SOI 9 Units / Rail M00E35R2 SOI 2500 / Tape & Reel M00E35R2G SOI 2500 / Tape & Reel M00E35T TSSOP 00 Units / Rail M00E35TG TSSOP 00 Units / Rail M00E35TR2 TSSOP 2500 / Tape & Reel M00E35TR2G TSSOP 2500 / Tape & Reel M00E35MNR4 FN 000 / Tape & Reel M00E35MNR4G FN 000 / Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BR0/. Resource Reference of pplication Notes N405/ E lock istribution Techniques N406/ esigning with PE (E at +5.0 V) N503/ EinPS I/O SPiE Modeling Kit N504/ Metastability and the EinPS Family N56/ Interfacing Between VS and E N672/ The E Translator Guide N00/ Odd Number ounters esign N002/ Marking and ate odes N020/ Termination of E ogic evices N066/ Interfacing with EinPS N090/ haracteristics of E evices 5

6 M0E35, M00E35 PKGE IMENSIONS X B Y 5 4 S 0.25 (0.00) M Y SOI NB SE ISSUE M K NOTES:. IMENSIONING N TOERNING PER NSI Y4.5M, ONTROING IMENSION: MIIMETER. 3. IMENSION N B O NOT INUE MO PROTRUSION. 4. MXIMUM MO PROTRUSION 0.5 (0.006) PER SIE. 5. IMENSION OES NOT INUE MBR PROTRUSION. OWBE MBR PROTRUSION S BE 0.27 (0.005) TOT IN EXESS OF TE IMENSION T MXIMUM MTERI ONITION TRU RE OBSOETE. NEW STNR IS Z G 0.25 (0.00) M Z Y S X S SETING PNE 0.0 (0.004) N X 45 M J MIIMETERS INES IM MIN MX MIN MX B G.27 BS BS J K M 0 0 N S SOERING FOOTPRINT* SE 6: mm inches *For additional information on our Pb Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOERRM/. 6

7 M0E35, M00E35 PKGE IMENSIONS TSSOP T SUFFIX PSTI TSSOP PKGE SE 94R 02 ISSUE 0.5 (0.006) T 0.5 (0.006) T U U S 2X /2 PIN IENT S 5 x V K REF (0.004) M T U S V S B U F 0.25 (0.00) M NOTES:. IMENSIONING N TOERNING PER NSI Y4.5M, ONTROING IMENSION: MIIMETER. 3. IMENSION OES NOT INUE MO FS. PROTRUSIONS OR GTE BURRS. MO FS OR GTE BURRS S NOT EXEE 0.5 (0.006) PER SIE. 4. IMENSION B OES NOT INUE INTERE FS OR PROTRUSION. INTERE FS OR PROTRUSION S NOT EXEE 0.25 (0.00) PER SIE. 5. TERMIN NUMBERS RE SOWN FOR REFERENE ONY. 6. IMENSION N B RE TO BE ETERMINE T TUM PNE -W (0.004) T SETING PNE G ETI E ETI E W MIIMETERS INES IM MIN MX MIN MX B F G 0.65 BS BS K BS 0.93 BS M

8 M0E35, M00E35 PKGE IMENSIONS FN SE ISSUE PIN ONE REFERENE B NOTES:. IMENSIONING N TOERNING PER SME Y4.5M, ONTROING IMENSION: MIIMETERS. 3. IMENSION b PPIES TO PTE TERMIN N IS MESURE BETWEEN 0.25 N 0.30 MM FROM TERMIN. 4. OPNRITY PPIES TO TE EXPOSE P S WE S TE TERMINS. 2 X X 0.0 ÇÇÇÇ ÇÇÇÇ ÇÇÇÇ TOP VIEW E MIIMETERS IM MIN MX REF b BS E 2.00 BS E e 0.50 BS K X SETING PNE 0.0 SIE VIEW (3) 2 e/2 4 X e E2 K 5 X b B NOTE 3 BOTTOM VIEW EinPS is a trademark of Semiconductor omponents INdustries, (SI). ON Semiconductor and are registered trademarks of Semiconductor omponents Industries, (SI). SI reserves the right to make changes without further notice to any products herein. SI makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SI assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Typical parameters which may be provided in SI data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. ll operating parameters, including Typicals must be validated for each customer application by customer s technical experts. SI does not convey any license under its patent rights nor the rights of others. SI products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SI product could create a situation where personal injury or death may occur. Should Buyer purchase or use SI products for any such unintended or unauthorized application, Buyer shall indemnify and hold SI and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SI was negligent regarding the design or manufacture of the part. SI is an Equal Opportunity/ffirmative ction Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBITION ORERING INFORMTION ITERTURE FUFIMENT: iterature istribution enter for ON Semiconductor P.O. Box 563, enver, olorado 027 US Phone: or Toll Free US/anada Fax: or Toll Free US/anada orderlit@onsemi.com N. merican Technical Support: Toll Free US/anada Europe, Middle East and frica Technical Support: Phone: Japan ustomer Focus enter Phone: ON Semiconductor Website: Order iterature: For additional information, please contact your local Sales Representative M0E35/