MC10H606, MC100H606. Registered Hex TTL to PECL Translator

Transcription

1 Registered ex TT to PEC Translator Description The MC10/ is a 6 bit, registered, single supply TT to PEC translator. The device features differential PEC outputs as well as a choice between either a differential PEC clock input or a TT clock input. The asynchronous master reset control is a PEC level input. With its differential PEC outputs and TT inputs the 606 device is ideally suited for the transmit function of a PPI bus type board to board interface application. The on chip registers simplify the task of synchronizing the data between the two boards. The device is available in either EC standard: the MEC 10 device is compatible with MEC 10K logic levels, with a V CC of +5.0 V while the 100 device is compatible with 100K logic levels, with a V CC of +5.0 V. Features Differential 50 EC Outputs Choice Between Differential PEC or TT Clock Input Single Power Supply Multiple Power and Ground Pins to Minimize Noise Pb Free Packages are Available* FN SUFFIX CASE 776 MARKING DIAGRAM* 1 MCxxx606G AWYYWW xxx = 10 or 100 A = Assembly ocation W = Wafer ot YY = Year WW = Work Week G = Pb Free Package *For additional marking information, refer to Application Note AND8002/D. ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 5 of this data sheet. *For additional information on our Pb Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SODERRM/D. Semiconductor Components Industries, C, 2006 November, 2006 Rev. 6 1 Publication Order Number: MC10606/D

2 1 OF 6 BITS Table 1. TRUT TABE Dn T/ Qn+1 D n D Q Q n Q n X X = OW to IG Transition R T * V BB * 1. When using PEC inputs, T must be tied to ground (0 V). 2. When using only one PEC input, the unused PEC input must be tied to V BB, and T must be tied to ground (0 V). 3. When using T, both PEC inputs must be tied to ground (0 V). Figure 1. ogic Diagram D1 D2 V CCT D3 D4 D5 V CCE D0 T V BB V CCE Q0 Q0 GND Q1 Q1 Q2 Q2 Figure 2. Pinout: (Top View) Q5 Q5 Q4 Q4 V CCE Q3 Q3 Table 2. PIN NAMES PIN D0 D5, T Q0 Q5 Q0 Q5 V CCE V CCT GND FUNCTION TT Data Inputs Differential PEC Clock Input TT Clock Input PEC Master Reset Input True PEC Outputs Inverted PEC Outputs PEC V CC (+5.0 V) TT V CC (+5.0 V) TT/PEC Ground 2

3 Table PEC DC CARACTERISTICS (V CCT = V CCE = 5.0 V ± 5%) T A = 0 C T A = 25 C T A = 85 C Min Max Min Max Min Max I IN Input IG Current A I IN Input OW Current A V I Input IG Voltage (Note 4) V CCT = 5.0 V mv V I Input OW Voltage (Note 4) V CCT = 5.0 V mv V O Output IG Voltage (Note 4) V CCT = 5.0 V mv V O Output OW Voltage (Note 4) V CCT = 5.0 V mv V BB Reference Voltage (Note 4) V CCT = 5.0 V mv operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 4. PEC V I, V I, V O, V O V BB are given for V CCT = V CCE = 5.0 V and will vary 1:1 with the power supply. Table PEC DC CARACTERISTICS (V CCT = V CCE = 5.0 V ± 5%) T A = 0 C T A = 25 C T A = 85 C Min Max Min Max Min Max I IN Input IG Current A I IN Input OW Current A V I Input IG Voltage (Note 5) V CCT = 5.0 V mv V I Input OW Voltage (Note 5) V CCT = 5.0 V mv V O Output IG Voltage (Note 5) V CCT = 5.0 V mv V O Output OW Voltage (Note 5) V CCT = 5.0 V mv V BB Output Bias Voltage (Note 5) V CCT = 5.0 V mv operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 5. PEC V I, V I, V O, V O V BB are given for V CCT = V CCE = 5.0 V and will vary 1:1 with the power supply. Table 5. DC CARACTERISTICS (V CCT = V CCE = 5.0 V ± 5%) T A = 0 C T A = + 25 C T A = + 85 C Min Typ Max Min Typ Max Min Typ Max I CC Supply Current Outputs OW ma I CC Supply Current Outputs IG ma I GND Supply Current ma operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 3

4 Table 6. TT DC CARACTERISTICS (V CCT = V CCE = 5.0 V ± 5%) T A = 0 C T A = 25 C T A = 85 C Min Max Min Max Min Max V I Input IG Voltage V V I Input OW Voltage V V IK Input Clamp Voltage I IN = 18 ma V I I Input IG Current V IN = 2.7 V V IN = 7.0 V I I Input OW Current V IN = 0.5 V ma operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously V Table 7. AC CARACTERISTICS (V CCT = V CCE = 5.0 V ± 5%) T A = 0 C T A = + 25 C T A = + 85 C Min Typ Max Min Typ Max Min Typ Max t PD Propagation Delay T++ 50 to V CC 2.0 V ns t PD Propagation Delay T+ 50 to V CC 2.0 V ns t PD Propagation Delay to V CC 2.0 V ns t PD Propagation Delay + 50 to V CC 2.0 V ns t PD Propagation Delay + 50 to V CC 2.0 V ns t SKEW Device Skew Part to Part Within Device 50 to V CC 2.0 V t S Setup Time 50 to V CC 2.0 V ns t old Time 50 to V CC 2.0 V ns t PW Minimum Pulse Width 50 to V CC 2.0 V ns t PW Minimum Pulse Width 50 to V CC 2.0 V ns t r Rise Time 50 to V CC 2.0 V ns t f Fall Time 50 to V CC 2.0 V ns t RES/REC Reset/Recovery Time 50 to V CC 2.0 V ns operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously ns 4

5 ORDERING INFORMATION Device Package Shipping MC10606FN 37 s / Rail MC10606FNG (Pb Free) 37 s / Rail MC10606FNR2 500 / Tape & Reel MC10606FNR2G (Pb Free) 500 / Tape & Reel MC100606FN 37 s / Rail MC100606FNG (Pb Free) 37 s / Rail For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. Resource Reference of Application Notes AN1405/D EC Clock Distribution Techniques AN1406/D Designing with PEC (EC at +5.0 V) AN1503/D ECinPS I/O SPiCE Modeling Kit AN1504/D Metastability and the ECinPS Family AN1568/D Interfacing Between VDS and EC AN1672/D The EC Translator Guide AND8001/D Odd Number Counters Design AND8002/D Marking and Date Codes AND8020/D Termination of EC ogic Devices AND8066/D Interfacing with ECinPS AND8090/D AC Characteristics of EC Devices 5

6 PACKAGE DIMENSIONS FN SUFFIX PASTIC PCC PACKAGE CASE ISSUE E N Y BRK B U D M 28 1 V W D X VIEW D D G (0.250) S T M S N S A R C E K1 G G1 J VIEW S (0.100) T SEATING PANE K F (0.250) S T M S N S VIEW S NOTES: 1. DATUMS, M, AND N DETERMINED WERE TOP OF EAD SOUDER EXITS PASTIC BODY AT MOD PARTING INE. 2. DIMENSION G1, TRUE POSITION TO BE MEASURED AT DATUM T, SEATING PANE. 3. DIMENSIONS R AND U DO NOT INCUDE MOD FAS. AOWABE MOD FAS IS (0.250) PER SIDE. 4. DIMENSIONING AND TOERANCING PER ANSI Y14.5M, CONTROING DIMENSION: INC. 6. TE PACKAGE TOP MAY BE SMAER TAN TE PACKAGE BOTTOM BY UP TO (0.300). DIMENSIONS R AND U ARE DETERMINED AT TE OUTERMOST EXTREMES OF TE PASTIC BODY EXCUSIVE OF MOD FAS, TIE BAR BURRS, GATE BURRS AND INTEREAD FAS, BUT INCUDING ANY MISMATC BETWEEN TE TOP AND BOTTOM OF TE PASTIC BODY. 7. DIMENSION DOES NOT INCUDE DAMBAR PROTRUSION OR INTRUSION. TE DAMBAR PROTRUSION(S) SA NOT CAUSE TE DIMENSION TO BE GREATER TAN (0.940). TE DAMBAR INTRUSION(S) SA NOT CAUSE TE DIMENSION TO BE SMAER TAN (0.635). INCES MIIMETERS DIM MIN MAX MIN MAX A B C E F G BSC 1.27 BSC J K R U V W X Y G K

7 ECinPS is a trademark of Semiconductor Components Industries, C (SCIC). MEC 10 is a trademark of Motorola, Inc. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, C (SCIC). SCIC reserves the right to make changes without further notice to any products herein. SCIC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCIC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Typical parameters which may be provided in SCIC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including Typicals must be validated for each customer application by customer s technical experts. SCIC does not convey any license under its patent rights nor the rights of others. SCIC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCIC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCIC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCIC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCIC was negligent regarding the design or manufacture of the part. SCIC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBICATION ORDERING INFORMATION ITERATURE FUFIMENT: iterature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado USA Phone: or Toll Free USA/Canada Fax: or Toll Free USA/Canada orderlit@onsemi.com N. American Technical Support: Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: Japan Customer Focus Center Phone: ON Semiconductor Website: Order iterature: For additional information, please contact your local Sales Representative MC10606/D