Gauge Gauge.119" thick 07 7 Guage.179" thick

Transcription

1 SQURE STEEL STRIGHT POLES (SSP) Specifications The Square Steel Straight Pole has been successfully installed in projects of all types for over 30 years and has become the most popular and economical pole option for all site lighting applications including retail, commercial, industrial and residential projects. Dimensions Shaft Size The popularity of this series is due to its full offering of sizes, heights and standard colors with complete offering of mounting options, accessories and select styles/colors stocked for immediate shipping. Square Steel Straight Shaft One piece construction 2 3/8 OD tenon, Open Top or Factory drilled Side Mount Options available Steel ase Plate 3 size options for anchor bolts. ll anchor bolts fully galvanized with 2 nuts and washer (bolts ordered as separate line item and paper template included as component of pole) Square base cover available (ordered as separate line item) Pole finished in weather proof powder coast paint in 4 standard colors 3 x 5 Gasketed hand hole standard Pole Height 3" 5" 10" 15.5" Tenon Top Pole Open Top Pole Ordering Information Ordering Example: SES T-0-D SES Series Height Size Gauge Mounting Drilling Color SES Square Steel Straight Pole Feet Feet Feet Feet Feet Note: Custom Pole heights available, just note required height (pole will be cut down to required height from next tallest pole heights offered) 40 4"x4" Shaft "x5" Shaft Gauge.119" thick 07 7 Guage.179" thick T 2 3/8" OD Tenon OT Open Top Pole 2 Drill T 2 7/8" OD Tenon 1. vailable in 11 gauge only 2. Open Top Poles include a pole cap 3. detailed drawing of custom drill pattern required must be submitted at time of ordering 0 No Drilling for Tenon and Open Top Pole 2 Drill Pattern 2 6 Drill Pattern 6 26 Drill Pattern 26 C Custom Drill Pattern 3 4 Drill Pattern Viper Small D WH L PS Dark ronze White lack Platinum Silver 3 Drill Pattern Viper Large ll Rights Reserved. Specifications subject to change without notice. Printed in U.S.. SLS /17

2 SQURE STEEL STRIGHT POLES (SSP) Ordering Information Pole Ht. ft m Nominal Shaft Dim. 70 Wind Load Rating Wall Thick. olt Circle (Sug.) olt Circle olt Sq. ase Plate (sq.) nchor olt Size olt Proj. Pole Wt (lbs) SES XX-XX " " 11" 8-11" " 10.25x0.75" 3/4x30x3" 4" 91 SES XX-XX " " 11" " " 12x1" 3/4x30x3" 4" 106 SES XX-XX " " 11" 8-11" " 10.25x0.75" 3/4x30x3" 4" 104 SES XX-XX " " 11" " " 12x1" 3/4x30x3" 4" 122 SES XX-XX " " 11" 8-11" " 10.25x0.75" 3/4x30x3" 4" 116 SES XX-XX " " 11" " " 12x1" 3/4x30x3" 4" 138 SES XX-XX " " 11" 8-11" " 10.25x0.75" 3/4x30x3" 4" 128 SES XX-XX " " 11" " " 12x1" 3/4x30x3" 4" 153 SES XX-XX " " 11" " " 12x1" 3/4x30x3" 4" 214 SES XX-XX " " 11" 8-11" " 10.25x0.75" 3/4x30x3" 4" 147 SES XX-XX " " 11" " " 12x1" 3/4x30x3" 4" 175 SES XX-XX " " 12" " 6-8.4" 12x1" 3/4x30x3" 4" 243 SES XX-XX " " 11" 8-11" " 10.25x0.75" 3/4x30x3" 4" 160 SES XX-XX " " 11" " " 12x1" 3/4x30x3" 4" 191 SES XX-XX " " 11" " " 12x1" 3/4x30x3" 4" 266 SES XX-XX " NR NR.119" 12" 8-11" " 10.25x0.75" 3/4x30x3" 4" 190 SES XX-XX " NR.119" 11" " " 12x1" 1x36x4" 4" 231 SES XX-XX " " 11" " " 12x1" 1x36x4" 4" 324 SES XX-XX " NR.179" 12" " " 12x1" 1x36x4" 4" llowable EP with 1.3 gust factor; To determine max; pole loading weight, multiply allowable EP by 30 lbs; Published allowable EP values based upon calculations of Spaulding Lighting llowable EP values for project requiring SHTO methodology are available upon request. Notes: Factory supplied template must be used when setting anchor bolts; Hubbell Lighting will deny any claim for incorrect anchorage placement resulting from failure to use factory supplied template anchor bolts. Stocked Poles olt Circle Diagram SES18401TD SES18401TWH SES18401TL SES22507TL SES22507TD SES22507TPS SES25501TD SES25507TL SES25507TD SES28507TD SES28507TL POLE-SES-18ftX4inSQ-11G-TENON-DRK RONZE POLE-SES-18ftX4inSQ-11G-TENON-WHITE POLE-SES-18ftX4inSQ-11G-TENON-LCK POLE-SES-22ftX5inSQ-7G-TENON-LCK POLE-SES-22ftX5inSQ-7G-TENON-DRK RONZE POLE-SES-22ftX5inSQ-7G-TENON-PLTINUM SILVER POLE-SES-25ftX5inSQ-11G-TENON-DRK RONZE POLE-SES-25ftX5inSQ-7G-TENON-LCK POLE-SES-25ftX5inSQ-7G-TENON-DRK RONZE POLE-SES-28ftX5inSQ-7G-TENON-DRK RONZE POLE-SES-28ftX5inSQ-7G-TENON-LCK olt Square Measurement Measurement vertical or horizontal from the center of the bolt to the center of the bolt. 4 Square Pole (10 olt Circle) (Min..C. = 8 ) (MX..C ) olt Circle Measurement Measure diagonal from the center of the bolt to the center of the bolt. Suggested ; bolt circle Square Pole (11 olt Circle) (Min..C. = 10 ) (Max..C. = 13.5 ) ll listed SES poles use paper template It s the contractors responsibilty to ensure that new poles will fit existing bases ll Rights Reserved. Specifications subject to change without notice. Printed in U.S.. SLS /17

3 SQURE STEEL STRIGHT POLES (SSP) ccessories Pole Cap Tenon Hand Hole Cover ase Cover T (2 3/8" OD) Order as a separate line item Pole ase Covers for Square Poles SC-4-XX /2" Sq x 5" Deep (use on 4" sq poles) 4" POLE CP " POLE CP " POLE CP Note: T Tenons are factory installed. For installation into open top poles, use TT1 tenon top adapter Note: Hand hole cover included with all new poles. Replacement parts: (2) (1) (3"x5") SC-4L-XX /4" Sq x 5" Deep (use on 4" sq poles) SC-5-XX /4" Sq x 5" Deep (use on 5" sq poles) SC-6-XX /4" Sq x 5" Deep (use on 6" sq poles) 1. Replace XX with two letter color designation nchorage Order as a separate line item 3/4" x 30" x 3" nchor olt T-30M38 qty: 4 1" x 36" x 4" nchor olt T-36M38 qty: 4 ase Detail Flat Washer ase Plate Flat Washer Hex Nut nchor olt Hex Nut Grout with drain Optional Level Foundation olt Projection Engineering of footing by others Note 1" x 42" nchor olt T-30M38 qty: 4 Fabricated from hight tensile steel, each anchor bolt has two nuts and two washers; Galvanized anchor bolts are hot dipped; (Galvanized includes threaded portion plus six inches minimum); nchor olt template included with pole purchase. Replacement Nut/Washer Kit /4" T30 Set " T36 Set /4" T42 Set Drill pattern Confirm proper mounting before ordering SIDE MOUNTING LOCTIONS VIPER DRILL PTTERN POLE TOP POLE TOP C D 4 Suggested distance from top of pole 2.50 Ø5/8 2X Ø5/ E F Denotes handhole location Rectangular rm Ø4 Pole Ø5 Pole Ø6 Pole Ø.875 HOLE X2 Ø HOLES Ø HOLES X26 drill pattern is a combination of both the X2 and X6 drill patterns #6 DRILL PTTERN X ll Rights Reserved. Specifications subject to change without notice. Printed in U.S.. SLS /17

4 SQURE STEEL STRIGHT POLES (SSP) Mounting rackets Order s accessories Side Mounting Locations EP Weight TTF-XX-XX 1,2 RET-XX 1,2 TET-XX 1,2,3 4" Square pole top tenon adapter 2 3/8" OD slipfitter for max. four fixtures (90 ) 4" Round pole top tenon adapter 2 3/8" OD slipfitter for max. four fixtures (90 ) Three sided pole top tenon adapter 2 3/8" OD slipfitter for max. three fixtures (120 ) 0.4ft 2 20lbs. 0.04m 2 9kgs. 0.2ft 2 20lbs. 0.02m 2 9kgs. 20lbs. 9kgs. TTF-XX-XX TTF-VIPER-XX SET-XX TTF-10 Single TTF-29 Twin 90 TTF-28 Twin 180 TTF-39 Triple 90 TTF-49 Quad 90 TTFViper Triple 90 plugged on 2 sides RET-XX TET-XX TTF-VIPER-XX 4" Square pole top tenon adapter 2 3/8" OD slipfitter for max. fixture (90 0) Drilled 3 sides for Viper and plugged on two sides 1 Replace X or XX with color designation 2 ll fitters drilled with drill pattern 26 (except for TTFVIPER). ny other drill pattern must be designated at time of ordering. 3 Must use 10" arm on fixture for 120 mounting Tenon Insert for single fixture mounting or tenon adapters TT14-XX 1,2,3 2 3/8" OD Tenon top adapter for 4" square open top poles, (slips 9" into pole aligns with #6 drill pattern) TT15-XX 1,2,3 2 3/8" OD Tenon top adapter for 5" square open top poles, (slips 9" into pole aligns with #6 drill pattern) 1 TT1 not required with tenon top pole. Use only for retrofit (specify 4" or 5" pole). 2 Replace XX with two letter color designation 3 Installed with one through bolt supplied with fitter. May require field drilling of pole for proper installation. 7" 4" TT-1* Two Fixture Mounting racket " I.D. internet adapter for standard round tenons. vailable in multiple finishes as shown. Use with SES series poles Maximum Weight Per Tenon EP Weight lbs (kg) Ft 2 (m 2 ) lbs. (kg) Twin (27.2) 1.2 (0.1) 24 (10.9) TT2-XX 1 24" 30" 610mm 762mm Three Fixture Mounting racket " I.D. internet adapter for standard round tenons. vailable in multiple finishes as shown. Use with SES series poles Maximum Weight Per Tenon EP Weight lbs (kg) Ft 2 (m 2 ) lbs. (kg) Triple (27.2) 2.3 (0.2) 44 (19.9) TT3-XX 1 ll Rights Reserved. Specifications subject to change without notice. Printed in U.S.. SLS /17 C C 24" 54" 610mm 1372mm

5 SQURE STEEL STRIGHT POLES (SSP) Mounting rackets Order s accessories Four Fixture Mounting racket " I.D. internet adapter for standard round tenons. vailable in multiple finishes as shown. Use with SES series poles Maximum Weight Per Tenon EP Weight lbs (kg) Ft 2 (m 2 ) lbs. (kg) Quad (27.2) 3.4 (0.3) 64 (29) TT-4-XX 1 D D 24" 78" 610mm 1981mm Four Fixture Mounting racket (90 ) Square 4" bottom with 2 1 / 2 " I.D. internet adapter for standard round tenons. vailable in multiple finishes as shown. Use with SES series poles Maximum Weight Per Tenon EP Weight lbs (kg) Ft 2 (m 2 ) lbs. (kg) Quad (27.2) 2.8 (0.3) 46 (20.8) TT-4X-XX 1 (90 ) 24" 30" 610mm 762mm TPR Series " I.D. internet adapter for standard round tenons. vailable in multiple finishes as shown. Use with SES series poles EP Weight ft 2 (m 2 ) lbs. (kg.) TPR-2-XX 1,5 2 1/2" to 2" pipe size tenon reducer 6 (2.7) TPR-3-XX 2,5 3" to 2" pipe size reducer 8 (3.6) TPR-4-XX 3.5 4" to 2" pipe size tenon reducer 9 (4.1) 1 racket slips over pole creating 2 3/8 OD Tenon (lower ID = 3 1/16") 2 racket slips over pole creating 2 3/8 OD Tenon (lower ID = ID = 3 1/2") 3 racket slips over pole creating 2 3/8 OD Tenon (lower ID = ID = 4 5/8") 4 Will not fit in 3 guage poles 5 Replace XX with two letter color designation TPR Series Ø.53 THRU Ø 3.50 WELD Ø.31 (2) PLCS THRU Ø 4.50 Ø 2.38 (2" PIPE) 285- Series " I.D. internet adapter for standard round tenons. vailable in multiple finishes as shown. Use with SES series poles 285- Series 4.25 WELD Ø 4.25 Ø 2.38 (2" PIPE) XX 1 3 1/2" to 2 3/8" Reducer (OD for both dimensions) XX 1 4 1/2" to 2 3/8" Reducer (OD for both dimensions) Ø.41 Ø.62 (2) PLCS THRU THRU 3.59 ID ll Rights Reserved. Specifications subject to change without notice. Printed in U.S.. SLS /17

6 SQURE STEEL STRIGHT POLES (SSP) Mid Pole racket Options Order s accessories 12" floodlight bracket for pole mounting FL-12-XX 1,2 (bracket requires internal pole access) 24" floodlight bracket for pole mounting FL-24-XX 1,2 (bracket requires internal pole access) 2 Mounting Hardware by others FL-12/ /8" OD tenon hole spacing 4 1/4 3 Sq. tubing 12"/ 24" 4041 Heavy-duty steel wall/pole bracket 2" pipe (2 3/8" OD) tenon fitting for use with slipfitter units or 4024C; In dark bronze finish Mounting Hardware by Others C 8 1/4" 9 1/2" 11" 210mm 241mm 279mm 4041 C S-302-XX 1 Slipfits 1 1/2" or 2" pipe (1.9" OD or 2 3/8" OD) with 1/2" N.P.S.M. hub; ronze.6(0.3) 1/2-14 NPT Threaded Entry 1/4-20 UNC SET SCREW S C Steel Slipfitter for 2 pipe, 2 3/8 OD yoke mount, bronze finish 1/2 OLTS TORQUE: FT-LS CM53 Steel Slipfitter for 2 pipe, 2 3/8 OD yoke mount, gray finish CM38 Steel Slipfitter for 2 pipe, 2 3/8 OD yoke mount, galvanized finish 4024C Pole Slip Fitter (1) Hardware Kit (1): Set Screw (3) 14/3 Cord Grip (1) 16/3 Cord grip (1) 1/2-13 Screw (2) 3/8 Nut (3) 1/2 Nut (2) Split Washer (2) 5 4 TTWM-XX 1 Wall Mount racket with 2 3/8" OD Tenon 2 Mounting hardware by others 1/2-13 SPILT WSHER (2) 1/2-13 SCREW (2) 3" SIDE MOUNT RCKET SSY Ø 2.38 (2" PIPE) SURFCE DRILL PTTERN REFERENCE /2-13 NUT (2) 2.50 Ø Ø.56 (2) PLCS TTWM ll Rights Reserved. Specifications subject to change without notice. Printed in U.S.. SLS /17

7 SQURE STEEL STRIGHT POLES (SSP) Pole Introduction Pole Selection Guide Poles should initially be selected, according to lighting application needs, and second, but equally important, according to the structural requirements imposed on the pole by the lighting fixtures, bracketry and wind. efore attempting to make this selection, it would be helpful to have an understanding of the terminology, such as steady or sustained wind velocity, gust velocity, EP, special wind region, and maximum weight. Then a step-by-step procedure can be followed to select the proper pole for your particular requirements. STEDY WIND OR SUSTINED WIND VELOCITY This is the maximum steady wind velocity expressed in likely to occur in a specific location. Refer to isotach wind map on the next page for the wind velocity in your location. Isotach maps are provided for reference only. Consult local authorities to determine the maximum velocities in your area. GUST VELOCITY Our isotach maps represent two different methods of addressing wind speed gusts. We have used the fastest-mile wind speeds for years. These have a 1.3 gust factor in the calculations to account for gusting. s technology has improved the ability to accurately measure wind speeds for short durations, the gusts associated to a sustained wind speed have lessened. We are now moving toward 3-second-gust wind speed maps. The results are typically higher steady/sustained wind speeds with lower factors for gusts. The gust factors are different depending on the wind speed map selected. EFFECTIVE PROJECTED RE Effective Projected rea (EP) is the exposed surface area of a fixture and bracket multiplied by a shape factor which varies depending on the shape of the fixture and bracket. For example, a large rectangular fixture will present more resistance to the wind than will a round or cylindrical shape. SPECIL WIND REGIONS Many locations such as mountainous areas, coastal areas and areas surrounding the Great Lakes exhibit wind velocities considerably higher than the surrounding areas. Consult local authorities to determine maximum wind velocities and select equipment accordingly. MXIMUM WEIGHT This is the maximum allowable weight based on EP loads. The weight is based on 30 pounds per square foot of EP. Weight exceeding the 30 pound per foot of EP may reduce the allowable EP rating of the pole. POLE SELECTION PROCEDURE With an understanding of the parameters for pole selection, you can follow this simple step-by-step procedure and, with confidence, select a pole to meet your particular requirements. 1. Determine the site location and steady wind velocity by referring to the appropriate isotach map. If the steady wind exceeds those listed, consult factory. The isotach maps are provided for reference only. Consult local authorities to determine the maximum velocities in your area. 2. Total the EP for the required luminaires and bracketry. 3. Total the weight of the luminaires and bracketry. 4. Compare steps 2 and 3 with the maximum allowable EP and weight tables shown for the style, material, and height pole required. The maximum allowable must be equal to or exceed the totals from steps 2 and 3. POLE SELECTION CONCERNS Caution: These selection methods are guidelines only. Hubbell Lighting assumes no responsibility for selection and recommends you consult qualified professionals for verification of overall system design, site suitability, foundation considerations and applica ble code and regulatory conformances. Maintenance: The facility owner s/manager s regular scheduled maintenance program must include initial and regular follow-up inspections for structural dam age, broken welds, tampering, nut loosening, missing wire covers, dangling electrical wiring, internal or external corrosion, foundation settlement, excessive shaft deflection and vibration for all lighting poles. Immediate repair or replacement may be necessary. Overloading: Do not overload poles by attaching flags, banners, or any items that can add excessive wind or mechanical load to designed pole assemblies. Observation: Installation and local area conditions can dramatically affect lighting pole performance. Excessive vibration may result from some wind and mounting conditions. Only individuals with local knowledge, who have observed or inspected the site can effectively evaluate site specific issues. Consult the factory for information on vibration dampers, spe cial corrosion, foundation settlement, excessive shaft deflection and vibration for all lighting poles. Immedi ate repair or replacement may be necessary. ll Rights Reserved. Specifications subject to change without notice. Printed in U.S.. SLS /17

8 SQURE STEEL STRIGHT POLES (SSP) Wind Speed Wind Map United States and Canada Special Wind Region (Consult Local uthorities) Florida region wind map above is based upon 3-second gust winds and the 2010 Florida uilding Code NOTES llowable EP, to determine max pole loading weight, multiply allowable EP by 30 lbs. NOTES: The tables for allowable pole EP are based on the SCE 7-05 Wind Map or the Florida Region Wind Map for the 2010 Florida uilding Code. The Wind Maps are intended only as a general guide and Values cannot be are used based in conjunction 50 year with mean other maps. recurrence lways consult interval local 30 authorities The to determine Wind Map maximum is intended wind velocities, only as gusting a general and unique guide. wind lways conditions for each specific application above llowable grade. pole EP for jobsite wind conditions must be equal to or greater than consult the total EP local for authorities fixtures, arms, to and determine accessories maximum to be assembled wind to the pole. Responsibility lies with the specifier for Hawaii correct pole has selection. an 105 Installation mph wind of poles velocity. without luminaires or attachment of any velocities, unauthorized gusting accessories and unique to poles wind is discouraged conditions and shall for each void the manufacturer s warranty specific application. Puerto Wind speeds Rico and has listed a 125 EPs mph are for wind ground velocity. mounted installations. Poles mounted on structures (such as bridges and buildings) must consider vibration and coefficient of height factors beyond this Caution general guide; must Consult be exercised local and in federal determining standards wind velocities CUTION: Wind speeds and listed EPs are for ground in Wind special Induced wind Vibration areas brought such as: on by steady, unidirectional winds and other unpredictable mounted aerodynamic installations. forces Poles are mounted not included on in structures wind velocity (such ratings. Consult Hubbell Lighting s Pole Vibration pplication Mountainous Guide for Regions environmental risk factors and design considerations. as bridges and buildings) must consider vibration and coefficient of height factors beyond this general guide. Extreme reas Wind surrounding Events like, the Hurricanes, Great Lakes Typhoons, or other Cyclones, large or Tornadoes bodies may expose poles to flying debris, wind shear or other detrimental effects not included in wind velocity ratings Consult SHTO standards. of water or open land. Extreme Wind Events: Hurricanes, Typhoons, Cyclones, or STEDY/SUSTINED reas subject to extreme WIND wind VELOCITY conditions, (Miles such as Per Hour, for Tornadoes KM/hr expose - multiply poles to values flying debris, by 1.61) wind shear, and hurricanes, typhoons, cyclones, and tornadoes. other unpredictable aerodynamic forces not indicated by reas adjacent to airports. the wind velocity ratings. Hawaii ny specific has an area 80 with a known wind velocity or suspected abnormally Pole Strength Limited Warranty: Standard, unmodified Kim high intermittent wind condition caused by geography, lighting Poles installed as recommended, undamaged by Puerto adjacent Rico structures, has a 95 or other specific wind velocity local conditions corrosion, or lack of maintenance, shall withstand steady Use that caution may not in be determining recorded National wind velocities Weather Service in special wind conditions areas such as provided as mountainous on page 2 (llowable areas, coastal Pole areas and areas surrounding records. EP). Installation of poles without luminaires, or attachment the Great Lakes llowable pole EP for jobsite wind conditions must be of any unauthorized accessories to poles shall void this Isotach equal to or map greater is provided than fixture for EP. reference Responsibility only. lies Consult with local warranty. authorities to determine the maximum velocities in your area the specifier for correct pole selection based on SHTO wind map and job location. Note The maximum allowable EP and weights are listed for each pole; The EP and weights are listed in this Selection Guide for each luminaire and bracket For information on SHTO Standards for Lighting Equipment contact: merican ssociation of State Highway and Transportation Officials 444 N. Capitol Street, NW, Suite 249 (202) SHTO standards used are found in the following publications: I-LTS-3 Standard Specification For Structural Support For Highway Signs, Luminaires nd Traffic Signals, (1994) I-LPH Guide for Standardizing Highway Lighting Pole Hardware, (1980) I-GL-5 n Informational Guide for Roadway Lighting, (1984) ll Rights Reserved. Specifications subject to change without notice. Printed in U.S.. SLS /17