Safety Rules and directions for use of pullers. Mechanical Pullers

Transcription

1

2 Safety Rules and directions for use of pullers Special: Pullers with Quick-Action- Nut EXTRA Decision criterias for the identification of a suitable puller: - gripping possibility determine, whether outside or inside - application-causes whether two or three-armed - dimensions and relative sizes compare with table data and select the right suitable puller Always use a larger and stronger puller in the case of doubt. Keep spindle clean and oiled, Set pullers reliably, Tighten firmly all bolt connections at the puller, if necessary use a fastening clamp against slipping of hooks. Keep danger zone shielded to exclude all risks. For your own security and for durability of the puller do not exceed: - table statements - ( ) - ( t / KN) The data and are determined with new pullers and are in accordance of valid safety regulations and are average values. Practice-conditioned wear and unfavourable circumstances may reduce these values. Please consider legal regulations for technical products. Grease-Hydraulic-Spindles Impact screwdriver prohibited. Accident risk by uncontrolled operation of pressure screws. For safety reasons turn always the pressure screws with a wrench pivot in accordance to table data. Tighten firmly all bolt connections at the puller. Oil-Hydraulic - control your work always with manometer - t-pullers use with t-hydraulics only - do never exceed the operating pressure of 700 bar for the complete hydraulic system (1 bar = 1 Kg/cm2 = N/cm2) Secure carefully the danger zone and keep it shielded. Tighten firmly all bolt connections at the puller. Details of dimensions and weights correspond with the present technical standard and are average values. Due to advancement we must subject to change. Qualität ISO 9001 NEXUS-Werkzeugfabrik Justus Schmidt GmbH&Co.KG Postfach 0 0 D-27 Remscheid TEL +9 (0) 2191/ 99-0 FAX +9 (0) 2191/ info@nexus.de

3 Contents of Article- NEXUS- page 0-F - 0-F0 0-FM - 0-F0M M M M M - - -SP -0H - -SPH -M - -SPM SP -0H - 7 -SPH -M - -SPM -0P - -SPP M - -0M -S - -S0 -SM - -S0M M - -0M 1 1-E,7 1-N 2 7 9, G , SP-0-0 NEXUS- page -0BUE S - 0 -S -H H1 - -H -HD -HS - -HS -M1 - -M -S -S -ST 1 7 1,, , , S 1-S H 0 -LH B,1-S SN - 1 -H -M 7, NEXUS- page NEXUS- page NEXUS- page NEXUS- page -P, -PK Pullers with Pullers with Pullers for -S,-SK Quick-Action Grease-Hydraulic Nut EXTRA Spindles Oil-Hydraulics 1-K 7 1-N1 7 E0-F H - HM 1-S E0-F0 -SPH HM T P, -2P , 12 1-N1 1-SN 1-29-S , 0 9, F2-0 F2-0 F2-0M F2-0M F- - F-SP F, F1 G, GS HO19- HO19- S 1 S-DIV 0 S-ST 1 S1 S S-1 E0-FM - E0-F0M E E1-0 E1-M - E1-0M E2- - E E2-M - E2-0M E E-0 E-M - 2 E-0M E-S - 21 E-S0 E-SM - 2 E-S0M E E-0 E-M - 2 E-0M E-0 21 E-0, E-1-1 E-2, E E-2 E-S E-S E-ST E1-0 2 E1-0, E1-1 - E1-2, E E1-2 E1-S 2 E1-S ES-0-19 ES- ES-ST ES1-0- ES H - -SPH -0P - -SPP -H -H1 - -H -HS 7 7 1,,9 1- A 1- B 1- T 1- V -H 9 9,9 0 -LH 0 -H 7 19-H 19-H 1 7 F2-0 F2-0 F2-0M F2-0M F- - F-SP F, F1 HM HM 9 HM 70 HM 71 HM1 72 HO HO11 7 HO HO 9 HO 70 HO 71 HO1 72 HO19,1 HP HY HY11 7 HY HY 9 HY 70 HY 71 HY1 72 HZ, HZ-,1, HZ- 1, Individual parts H H H H H H H H H H 000 H H H H H H H H H Name of Articles page page Pullers with: page Scissor-Action Arms... Ball Bearing Extractors... Krallex-Pullers Side Clamp...,, Ball Bearing Extractor Sets arm,-arm, 1-2,, 0 Slide Haer...,, 2, Krallex-Pullers -FUSS-..., 21,, 0 Spread-Adjuster... Ball Joint Extractors for: Krallex-Pullers -SCHAFT-..., 21,, 0 Cars, Vans... 7,, 9, Krallex-Pullers with Leg-Clamp Self-Centering-Pullers..., 1,, Medium Trucks... 7, 9, Separators / Pullers..., 2, Heavy Trucks... 1 Mini-Pullers..., 1 Release+Push Out Set... Needle Bearing Extractors Ball Joint Separators Fork Type... Nut Splitters... 7 Bolt Extractor Sets... Cam Shaft Wheels Puller Set... Counter Stay Devices... 7 Flange Spreader Set... 7 Flange Type Axle Puller... Grease-Hydraulic-Spindles-Program, 1, 7, 1-0 Internal Extractors Oil-Hydraulic-Program..., 1, 1-72 Passenger Car-V-Belt-Pulley Puller-Set with Groovehooks... Puller Chuck... Pullers for heavy work..., Quick-Action-Nut EXTRA Pullers 1,, 19,, 21, 2, 2 Side Clamp... Slide Haers... Spindles / Tie Rods... Spring-Compressors... Stearing Wheel Puller... Stud Pullers... Universal-Pullers 2-arm, -arm , 1, 1,,,, 0 Wheel-Hub-Pullers... Windscreen-Wiper-Arm-Puller-Set... 2 Workshop-Sets, Stands, Sales-Display, 9,, 11, 1,, 2, 2, 7,,, 9 Oil-Hydraulic Grease-Hydraulic EAN-Code-List on request 1

4 Grease-Hydraulic Oil-Hydraulic Grease-Hydraulic Oil-Hydraulic General view Internal Extractors multiple slots page page, 7 Slide Haers page 7 Universal-Pullers with Quick-Action-Nut EXTRA 2-arm -arm 2-arm -arm page page 1 page 1 page Mini-Pullers also for Battery Terminals, Windscreen-Wiper-Arms page page 1 Separators and Pullers page 2 page Ball Joint Separators Fork Type Separator-/ Puller Sets Ball Joint Extractors page page Spring- Compressors page Mini-Pullers 2- / -arm Ball Joint Extractors for cars, vans page 7 Internal Extractors, -arm great spread Counter Stay Devices page 7 Pullers, adjustable legs 2- / -arm page 2 Separator Pullers Pullers with Side Clamp with Side Clamp page page Ball Joint Extractor adjustable for cars page 9 Workshop-Sets page 9,, 9 Pullers 2-arm page Ball Joint Extractors, adjustable for cars, van, medium trucks page 9 Stud Pullers Flange Spreader Set Nut Splitters mechanical / hydraulic Stearing Wheel Pullers page page 7 page 7 page 2

5 NEW Needle Bearing Extractor Sets page, 2,0 2-arm page 1-2 Krallex-Pullers -arm page, 2 Ball Bearing Extractors page Ball Bearing Extractor Sets page 11 NEW General view Side Clamp with Quick-Action-Nut EXTRA for Universal-Pullers, 2-arm page 19, 21, 2, 2 page 1, 19 page 2 NEW with Spread-Adjuster Pullers self centering page page Ram Grease -Hydraulic page 7 Puller Set for Cam Shaft Wheels page Ball Joint Extractor, adjustable for vans and medium trucks Pullers self centering page page 1 Pullers, double ended / reversible legs 2- / -arm Groovehooks page 2 page 29 Puller with Krallex- Passenger Car-V-Belt-Pulley Puller-Set with Groovehooks Legs, Leg Clamp page page Ball Joint Extractor, adjustable for heavy trucks, busses, low floor busses NEW NEW Pullers, adjustable legs 2- / -arm NEW Ball Joint Extractors, adjustable with Grease-Hydraulic or Oil-Hydraulic page, 1 Oil-Hydraulic Grease-Hydraulic Release + Push Out Set Four-guide-rod-front-axle for cars: Audi, VW, Quattros page Pullers with Scissor-Action Arms Universal-Windscreen-Wiper-Arm-Puller-Set page page 2

6 Grease-Hydraulic - Program - Program General view Ram Grease-Hydraulic t / 1 t page 7 Nut Splitters Grease-Hydraulic page 7 Grease-Hydraulic-Spindle t / 0 KN t / 0 KN UN 1 1/2 x 1 page Grease-Hydraulic-Spindle t / 0 KN G 1/2 x page Grease-Hydraulic-Spindle t / 0 KN G / x page Grease- Hydraulic-Spindle 1 t / KN G 1 x 11 page Grease-Hydraulic System-Pullers page, 9 Universal-Pullers page, Universal-Pullers page Universal-Pullers, Beam-arms are radially adjustable page 7 Pullers, -arm page 0 Ball Joint Extractor, adjustable for vans, medium trucks page Ball Joint Extractor, adjustable for heavy trucks, busses, low floor busses page 1

7 Oil-Hydraulic - Program General view Hydraulic Hand Pump mechanical pneumatic electrical page Hydraulic Cylinders page, Hydraulic Hollow Piston Cylinder Hydraulic Cylinder with Spindle Flat-Cylinders Ball Joint Extractor, adjustable for vans, medium / heavy trucks, busses, low floor busses page, 1 Universal-Pullers with Oil-Hydraulic page Universal-Pullers with Oil-Hydraulic, Beam-arms are radially adjustable page 70 Pullers, - / -arm Beam-arms are radially adjustable page 71 Oil-Hydraulic Pullers, -arm page 7,, 9 Pullers, - / -arm Beam-arms are radially adjustable page 72

8 1 Internal Extractors multiple slots 1 - E Internal Extractors, -arm with great spread sturdy design with 1 - E, 1 - E 7, 1 - E spread T C A A min. - T Counter Stay Device suitable for Slide Haer adapterthread C 1 with Counter Stay Device 1-0 A 1-0 A B 1-0 B C 1-1 A 1-1 A B 1-2 A 1-2 A B 1-2 C 1 - A 1 - B 1 - A 1 - E 1 - B 1 - A 1 - B 1 - A 1 - A B 1 - E A 1-7 B 1 - E Counter Stay Device A , 2 -, - Slide Haer 2-01 Slide Haer 2-01A Slide Haerer 2-02 Slide Haer 2-02A 2-0 M M M M M M M M M M M M M M M M M M M M M M G / G / G / G / ,0 0,0 0,0 0,0 0,0 0,0 0,0 0,07 0,09 0,09 0,09 0,11 0,11 0,11 0, 0,2 0,2 0,2 0,2 0,29 0, 0,1 0,7 0, 0, 1, Succession

9 1 - E Internal Extractors, -arm with great spread sturdy design with 1-E,-E7,-E spread E 1 - E E A min T 0 Counter Stay Device 2-1,-1A,-1, 2-1,, -2,-,- 2-, - suitable for Slide Haer 2-01,-01A,-02,-02A 2-02A, A, -0 C adapterthread C M G / G / T A with Counter Stay Device ,2 0,7 1, 2 Counter Stay Devices for Internal Extractors , A 2- suitable for Internal Extractors adapterthread C min. - spindles A 2-1, A to - B + 1- E 1-0A to - B + 1- E 1- B to - 7B + 1- E, - E7 1-7A to - 7B + 1- E7 1-7A to - 7B + 1- E7, - E 1-7A to - 7B + 1- E7, - E M M M + G / G / G / G / M1 x 1, x M1 x 1, x M2 x 1, x M2 x 1, x M2 x 1, x G1/2 x x ,7 1,0 1, 1,,7, 2-0 Slide Haers for Internal Extractors 2-01A 2-02 suitable for Internal Extractors adapterthread C Slide Haer weight of Haer measurements of rod A A A to - 2B + 1- E 1-0A to - B + 1- E 1-2C to - B + 1- E 1-2C to - 7B + 1- E,-E7,-E 1-7A to - 7B + 1- E7, - E M M M M + G / G / x 0,2 0 x 0 0,7 x 0,7 x 0,7 0 x 1,7 x 0 x 0 1 x 0 1 x 0 1 x 0 0, 0,9 1, 1, 2, Internal Extractor Sets: page 9 and 9 7

10 1 - N Needle Bearing Extractor Sets in box also for ball bearings and bushings 1-N SK 1-N SK for bores: dia., 1, 1 for cars: Audi, BMW, Citroen, Fiat, Ford, DB, Opel, Peugeot, Porsche, Renault, Rover, Saab, Volvo, VW, Nissan, Datsun, Toyota... Needle Bearing Extractor Sets 1-NS Slide Haer with Holder 1-N Pair of legs with distance wedge for example: Bushing contents 1 - N SK 1 - N SG for bores: dia., 1, 1 for bores: dia pair of legs, distance wedges, 1 slide haer with holder pair of legs, distance wedges, 1 slide haer with holder 1,0 2,00 Pair of legs with distance wedge ( = pair of legs with 1 distance wedge ) 1 - N 11 for bores: dia N 1 - N 1 - N 1 - N N N 1 - N N N for BMW, Opel for Audi for Audi, DB, Ford, Opel, Porsche, VW 0,11 0, 0, 0, 0, 0, 0, 0,1 0,1 0,1 Holder, loose 1 - N 0 adapter-thread M for all legs 0, Slide Haer with Holder 1 - N S adapter-thread M for all legs 1, 9 Taper Roller Bearing Pullers for inner rings of taper roller bearings Detailed table of use with bearing-numbers on request Intructions for use: Place the gripping edge of the two segments carefully behind the rolls of inner ring of taper roller bearing. Clamp both segments with collar firmly. Use a suitable two or three leg puller for pulling off the integrated whole.

11 0 Internal Extractor- / Puller - Sets -A -S -K 0-N -B Internal Extractor- / Puller- Sets in metal box 0-G min. - contents - A - B - C - K - S 0 - G 0 - K 0 - N pieces: 1-1A, -2A, -A, -A, -A, -A, pieces: 1-1A, -2A, -A, -A, -A, -A, -E7, 2-1, -2 pieces: 1-1A, -2A, -A, -A, -A, -A, -E7, -E, 2-1, - 7 pieces: 1-1A, -2A, -A, -A, -A, 2-01, -1 pieces: 1-2A1, -A, -E, -E7, 2-1, pieces: 1-1A, -2A, -A, -A, -A, -A, -E7, -E, 2-1, -, -1, -2, 1-1, pieces: 1-1A, -2A, -A, -A, -A, -A, 2-1, -1, 1-1, pieces: 1-1A, -2A, -A, -A, -A, -A, -E7, 2-1, -2, -1, -2, 1-1,,,0,00,,0,00 7, 1, 9

12 0 / 1 Ball Bearing Extractors for easy removal of ball bearings seated on a shaft or in a housing Instructions for use: Insert the pulling legs between the balls in the outer bearing race. Apply tension to the legs by turning spindle. Extractor = Beam with spindle and grip Extractor without legs Extractor without legs Extractor without legs Extractor without legs Extractor without legs Legs ( = pieces ) corresponding legs see table below 0, 0, 0, 0,9 1,2 for extractor Examples of use , - 0-2, -, -, - 0 -, ,1 0,1 0,2 0,2 0, 0, 0, 0, Table of Ball Bearing Extractors 0 / 1 extractor leg for ISO Ball Bearings * 2* * 9* * * * * * Ball Bearings with ( * ) are removed by means of bracing parts to be fixed on leg-tip ( 1- ) Non-listed bearings on request Ball Bearing Extractor Set in metal box contents for ISO Ball Bearing 0 - G pieces: 0-1 to -, 1-1 to ,00

13 Ball Bearing Extractor Sets 2-1 Ball Bearing Extractor Sets, -arm with radially adjustable arms, in box NEW for ISO - Ball Bearings Capable of removing bearings from blind housings without dismantling machinery of removing running shaft. Also capable of removing bearings from running shaft, when not enough space for outside gripping. e.g.: SKF, FAG, Timken, NTN and comparable bearings from other bearing manufacturers min. - Leg ( = pieces ) Leg-tip: dia. spindle thread x-length To KN Contents 1 pieces: 1 beam -arm leg sets ( pieces each ) leg extensions screw pins 1 spindle 2 spindle extensions H1 2-H2 2-H 2-H 2-H 2-H M x 1, x ,, 9 11, 2-1K H1 2-H2 2-H M x 1, x ,0 Contents pieces: 1 beam -arm, leg sets ( pieces each ) leg extensions screw pins 1 spindle 2 spindle extensions Instructions for use: Between the balls drill a hole into the cage. Put the legs into this hole and turn them by Firstly fit right size of one leg with the rigid arm of beam - Fit this leg into the hole - Fit spindle in middle of running shaft with light tension Following fit the remaining two legs into the hole and into the beam arms. - Fix the radially adjustable arms of the beam in right position - with round nut on top of the beam fix the arms at the beam to form an integrated whole Patent pending Advantages: -arm working! Possible assembling upto -arm working. Arms radially adjustable depending to number of balls. Easy handling by one worker - form an integrated whole for safe pulling - no twisting of legs - no sideslip Unlimited reach by optional additonal leg extensions. rigid connection: one arm with beam two radially adjustable arms ( screw pins for fasten of legs ) red points are references for assembling Start with rigid arm and fit spindle in middle of running shaft with light tension. Keep your hands free for assembling of remaining legs. standard reach 90 leg extension: plus 9 for unlimited reach 11

14 90 Pullers, 2-arm Inside and outside use , min Legs ( = 1 pair ) inside min ,, for 90-1, , , spindles M x 1, x 0 M x 1, x 0 G 1/2 x x 2 G 1/2 x x 2 G / x x 20 G / x x 20 legs a b c d,,, ,9 1,0 2,7,0, 7, 0, 1,1 2,7 9 Puller, 2-arm with Krallex-Legs with integrated Leg-Clamp Patent pending NEW Advantage of Krallex-Legs: for extreme narrow spaces Advantage of Leg-Clamp: to prevent slipping out of position min. - spindle leg a b c d , M x 90 2, 2, 0, Leg ( = 1 pair ) for , 0 2, 0,2 Puller, 2-arm with Special-Krallex-Legs with integrated Leg-Clamp for extreme narrow spaces t KN SP , 1 M x 90 2, 1 0, Special-Leg ( = 1 pair ) for 91 SP SP 2, 0 1 0,2

15 Universal-Pullers page 0 0-1, page page 0 0-2, page /00 - page /00 -, page /00 - page 2 0/700 - page Puller-Set with Special-Legs 1-1 page 1 1-1, page page 1 1-2, page 1 Universal-Pullers with Quick-Action-Nut EXTRA E-1 page E1-1 page Krallex-Pullers page page E-1, page E1-1, page page page E-2 page E1-2 page page page E-2, page E1-2, page page page Krallex-Pullers with Quick-Action-Nut EXTRA FUSS- 2 -SCHAFT- Pullers for heavy work mechanical mechanical Grease- Hydraulic- Spindle page 0-90 / , E 1, E1 page / S,E-S 1-S,E1-S page /00 -M page /7 -M page /0 E- page 19 E- page 19 E- page 19 E-2 page 19 -H page Oil-Hydraulic 2 E1- page 2 E1- page 2 E1- page 2 E1-2 page 2 HY page Universal-Pullers with parallel gripping legs

16 Universal-Pullers, 2-arm Inside and outside use parallel gripping with legs for standard reach See table for extended legs, if more reach is necessary Variants: more power with Hydraulics B B A C A min. - B inside C min. - spindles legs a b c d - 1-1, - 2-2, - -, ,,,, M x 1, x 0 M x 1, x 0 G 1/2 x x 2 G 1/2 x x 2 G / x x 20 G / x x 20 G / x x 20 G 1 x 11 x ,0 1,2,0, 7,,,0 2,7 Legs ( = 1 pair ) for -1, , , , -1. 0, 0, 1,0 1, , , , , 1, 2, SP to 00 adjustable -, -., - -, -., - -, -., - -, -., - -, -., -,,1, 7,, SP 2 0 to 700 adjustable ,,0 7,,,0 fitting Oil-Hydraulics up to page 2 fitting Grease-Hydraulic up to page

17 E Universal-Pullers, 2-arm with Quick-Action-Nut EXTRA Inside and outside use parallel gripping with legs for standard reach See table for extended legs, if more reach is necessary Variants: more power with Grease-Hydraulic- Spindle B B A C A min. - B inside C min. - spindles legs a b c d E - 1 E - 1, E - 2 E - 2, ,,,, M x 1, x 0 M x 1, x 0 G 1/2 x x 2 G 1/2 x x ,0 1,2,0, Legs ( = 1 pair ) E 1-90 E 1-0 E 1 - E for E-1, E-1. E-1, E-1. E-1, E-1. E-1, E-1. 0, 0, 1,0 1,2 E 2 - E 2-0 E E-2, E-2. E-2, E-2. E-2, E , 1, 2, fitting Grease-Hydraulic up to page 1

18 1 Universal-Pullers, -arm Inside and outside use parallel gripping with legs for standard reach See table for extended legs, if more reach is necessary Variants: more power with Grease-Hydraulic- Spindle B A A min. - B spindles legs a b c d , , ,, M x 1, x 0 M x 1, x 0 G 1/2 x x 2 G 1/2 x x , 1,,,0 Legs ( = pieces ) for 1 - M 1-0 M 1 - M 1-0 M , , , , 1-1, 0,7 0,9 1, 1, 2 - M 2-0 M 2-0 M , 1-2, 1-2, 1-2, 1-2, 1-2, ,9 2,, - ST S - ST Sales-Display and Workshop-Stand Universal-Pullers, 2-arm A min. - B contents - ST S - ST S - ST 1 S - ST 2 S - ST pieces: -1, -1., -2, -2., - pieces: 1-2, -1, -1., -2, -2, pieces: -1, 2x -1., -2, -2, pieces: 1-, -1, -1., -2, -2, pieces: -1, -1., -2, -2,,, 11,,7, 1 fitting Grease-Hydraulic up to page

19 E1 Universal-Pullers, -arm with Quick-Action-Nut EXTRA Inside and outside use parallel gripping with legs for standard reach See table for extended legs, if more reach is necessary Variants: more power with Grease-Hydraulic- Spindle B A A min. - B spindles legs a b c d E1-1 E1-1, E1-2 E1-2, ,, M x 1, x 0 M x 1, x 0 G 1/2 x x 2 G 1/2 x x , 1,,,0 Legs ( = pieces ) for E1 - M E1-0 M E1 - M E1-0 M 0 0 E1-1, E1-1. E1-1, E1-1. E1-1, E1-1. E1-1, E1-1, 0,7 1,0 1, 1, E2 - M E2-0 M E2-0 M 0 0 E1-2, E1-2, E1-2, E1-2, E1-2, E1-2, ,0 2,, E - ST ES - ST Sales-Display and Workshop-Stand Universal-Pullers, 2-arm with Quick-Action-Nut EXTRA min. - contents E - ST ES - ST ES - ST 1 ES - ST 2 ES - ST pieces: E-1, E-1., E-2, E-2., - pieces: 1-2, E-1, E-1., E-2, E-2, pieces: E-1, 2x E-1., E-2, E-2, pieces: E1-, E-1, E-1., E-2, E-2, pieces: E-1, E-1., E-2, E-2,,, 11,,7, fitting Grease-Hydraulic up to page

20 Krallex-Pullers with parallel gripping legs - Krallex-Pullers, 2-arm Leg-tip flat Leg-body narrow parallel gripping with legs for standard reach See table for extended legs, if more reach is necessary Variants: B A A min. - B spindles legs a b c d ,,,, M x 1, x 0 M x 1, x 0 G 1/2 x x 2 G 1/2 x x 2,, 1,0 1,2,0, Legs ( = 1 pair ) for -, - -, - -, - -, - -, -2 -, -2 -, -2,,,, 0, 0, 1,0 1,2 1, 1, 2, S S1 Krallex-Puller-Sets, 2- and -arm Leg-tip flat Leg-body narrow various reach 2-arm S - 0 S - 0, min / / / 0 a 2,0 2,0 2,0,2 S - S / / / 0,, 2,0,2 S-0, S1- Info: S-DIV - One for all purposes - page 0 -arm S1-0 S1-0, S1 - S / / / 0 / / / 0 2,0 2,0,, 2,7, 2,7, 1

21 Krallex-Pullers with parallel gripping legs E - Krallex-Pullers, 2-arm with Quick-Action-Nut EXTRA Leg-tip flat Leg-body narrow parallel gripping with legs for standard reach See table for extended legs, if more reach is necessary Variants: B A A min. - B spindles legs a b c d E - E - E - E ,,,, M x 1, x 0 M x 1, x 0 G 1/2 x x 2 G 1/2 x x 2,, 1,0 1,2,0, Legs ( = 1 pair ) for E - E - 0 E - E - 0 E - E - 0 E E-, E- E-, E- E-, E- E-, E- E-, E-2 E-, E-2 E-, E-2,,,, 0, 0, 1,0 1,2 1, 1, 2, ES ES1 Krallex-Puller-Sets, 2- and -arm with Quick-Action-Nut EXTRA Leg-tip flat Leg-body narrow various reach 2-arm ES - 0 ES - 0, min / / / 0 a 2,0 2,0 2,0,2 ES - ES / / / 0,, 2,0,2 -arm ES1-0 ES1-0, / / / 0 2,0 2,0 2,7, ES-0, ES1- ES1 - ES / / / 0,, 2,7, 19

22 Krallex-Pullers with parallel gripping legs FUSS - Krallex-Pullers, 2-arm Leg-tip extreme flat Leg-body narrow 2 min. - spindles legs a b c d - 0-0, ,, M x 1, x 0 M x 1, x ,0 1,2 Krallex-Legs - FUSS - ( = 1 pair ) for 0 - F 0 - F F 0 - F , -0, -0, -0, -0, -0, -0, -0, , 0, 1,0 1,2 - S - SCHAFT - Krallex-Pullers, 2-arm Leg-body extreme narrow Leg-tip flat min. - spindles legs a b c d - S - S , 2, Mx1, x 0 Mx1, x 0,, 1,0 1,2 Krallex-Legs - SCHAFT - ( = 1 pair ) - S - S S - S 0 0 for -S, -S -S, -S -S, -S -S, -S,,,, 0, 0, 1,0 1,

23 Krallex-Pullers with parallel gripping legs E FUSS - Krallex-Pullers, 2-arm with Quick-Action-Nut EXTRA Leg-tip extreme flat Leg-body narrow 2 min. - spindles legs a b c d E - 0 E - 0, ,, M x 1, x 0 M x 1, x ,0 1,2 Krallex-Legs - FUSS - ( = 1 pair ) E0 - F E0 - F 0 0 E0 - F E0 - F 0 0 for E-0, E-0, E-0, E-0, E-0, E-0, E-0, E-0, , 0, 1,0 1,2 E - S - SCHAFT - Krallex-Pullers, 2-arm with Quick-Action-Nut EXTRA Leg-body extreme narrow Leg-tip flat min. - spindles legs a b c d E - S E - S , 2, Mx1, x 0 Mx1, x 0,, 1,0 1,2 Krallex-Legs - SCHAFT - ( = 1 pair ) E - S E - S 0 0 E - S E - S 0 0 for E-S, E-S E-S, E-S E-S, E-S E-S, E-S,,,, 0, 0, 1,0 1, 21

24 Krallex-Pullers with parallel gripping legs 1 - Krallex-Pullers, -arm Leg-tip flat Leg-body narrow parallel gripping with legs for standard reach min See table for extended legs, if more reach is necessary 90 90,0,0,, 0 0 spindles M x 1, x 0 M x 1, x 0 G 1/2 x x 2 G 1/2 x x 2 legs a b c d,, 1, 1,,,0 Krallex-Legs ( = pieces ) for - M - 0 M - M - 0 M - M - 0 M - 0 M , 1-1-, 1-1-, 1-1-, 1-1-, , , 1-2,,,, 0,7 0,9 1, 1, 1,9 2,, FUSS - Krallex-Pullers, -arm Leg-tip extreme flat Leg-body narrow 2 min. - spindles legs a b c d , M x 1, x 0 M x 1, x , 1, Krallex-Legs - FUSS - ( = pieces ) 0 - F M 0 - F 0 M F M 0 - F 0 M 0 for 1-0, 1-0, 1-0, 1-0, 1-0, 1-0, 1-0, 1-0, ,7 0,9 1, 1, 1 - S - SCHAFT - Krallex-Pullers, -arm Leg-body extreme narrow Leg-tip flat 1 - S 1 - S M x 1, x 0 M x 1, x 0,, 1, 1, Krallex-Legs - SCHAFT - ( = pieces ) - S M - S 0 M 0 - S M - S 0 M 0 for 1-S, 1-S 1-S, 1-S 1-S, 1-S 1-S, 1-S,,,, 0,7 0,9 1, 1,

25 Krallex-Pullers with parallel gripping legs E1 - E1 - E1 - E1 - E1-2 min Krallex-Pullers, -arm with Quick-Action-Nut EXTRA Leg-tip flat Leg-body narrow parallel gripping with legs for standard reach See table for extended legs, if more reach is necessary 90 90,0,0,, 0 0 spindles M x 1, x 0 M x 1, x 0 G 1/2 x x 2 G 1/2 x x 2 legs a b c d,, 1, 1,,,0 Krallex-Legs ( = pieces ) E - M E - 0 M E - M E - 0 M E - M E - 0 M E - 0 M for E1-, E1- E1-, E1- E1-, E1- E1-, E1- E1-, E1-2 E1-, E1-2 E1-, E1-2,,,, 0,7 0,9 1, 1, 1,9 2,, E1-0 - FUSS - Krallex-Pullers, -arm with Quick-Action-Nut EXTRA Leg-tip extreme flat Leg-body narrow 2 min. - spindles legs a b c d E1-0 E1-0, M x 1, x 0 M x 1, x , 1, Krallex-Legs - FUSS - ( = pieces ) E0 - F M E0 - F 0 M 0 E0 - F M E0 - F 0 M 0 for E1-0, E1-0, E1-0, E1-0, E1-0, E1-0, E1-0, E1-0, ,7 0,9 1, 1, E1 - S - SCHAFT - Krallex-Pullers, -arm with Quick-Action-Nut EXTRA Leg-body extreme narrow Leg-tip flat E1 - S E1 - S M x 1, x 0 M x 1, x 0,, 1, 1, Krallex-Legs - SCHAFT - ( = pieces ) E - S M E - S 0 M 0 E - S M E - S 0 M 0 for E1-S, E1-S E1-S, E1-S E1-S, E1-S E1-S, E1-S,,,, 0,7 0,9 1, 1, 2

26 Krallex-Pullers with parallel gripping legs - 0BUE Side Clamp for 2-arm Universal-Pullers 0 spread Examples of use - 0BUE for pullers with 0 spread 0, S1 Krallex-Puller-Sets, 2- and -arm in box ES1 Krallex-Puller-Sets, 2- and -arm with Quick-Action-Nut EXTRA in box S1-11 ES1-11 S1-11 S1 - S1-1 S1-1 min legtip a, 2,0, 2,0 2,0 2,0 2,2 2,2 ES1-11 ES1 - ES1-1 ES1-1 min legtip a, 2,0, 2,0 2,0 2,0 2,2 2,2 2

27 - M Universal-Pullers, -arm sturdy design for heavy duty work, exchangeable legs for more reach, legs are always parallel gripping more power with Hydraulics - M 1 - M 2 - M min spindles G 1 x 11 x G 1 x 11 x G 1 x 11 x legs a b c d 21 Legs ( = pieces ) - M - 0 M 0-0 M 0-00 M 00 - SP M adjustable 0 to 00 for -M1, -M2, -M -M1, -M2, -M -M1, -M2, -M -M1, -M2, -M -M1, -M2, -M,0 7, 9, 11,7,7 - M Universal-Puller, -arm sturdy design for heavy duty work, exchangeable legs for more reach, legs are always parallel gripping Beam-Arms are radially adjustable more power with Hydraulics min. - - M spindles legs a b c d 0 1 G 1 x 11 x , Legs ( = pieces ) - M - 0 M 0-0 M 0-00 M 00 - SP M adjustable 7 to 7 for -M -M -M -M -M , 9,0 11,0,,0 fitting Oil-Hydraulics up to page 2 fitting Grease-Hydraulic up to page

28 11 Pullers, 2-arm adjustable legs, during lever action legs press closely under the parts to be removed min. - spindles legs a b c d ,,0 M x 1, x 0 M1 x 1, x , ,0 2, 11 Pullers, -arm adjustable legs, during lever action legs press closely under the parts to be removed min. - spindles legs a b c d ,0, M x 1, x 0 M1 x 1, x , ,,1 2

29 11 Pullers, 2-arm with Side Clamp Puller for Inner Races of front wheel hubs page spindles legs a b c d , M1 x 1, x 0 G 1/2 x x 2 G 1/2 x x 2 M1 x 1, x , ,7 2,, 1,9 119 Separator Pullers, 2-arm with Side Clamp double ended / reversible legs spindles legs a b c d M1 x 1, x 2 G 1/2 x x 0 G 1/2 x x ,,1,

30 1 2 Pullers, 2-arm double ended / reversible legs, one end broad, other end narrow, during lever action legs press closely under the part to be removed min. - spindles legs a b c d ,,0 M x 1, x 0 M1 x 1, x ,9 2,2 Pullers, -arm double ended / reversible legs, one end broad, other end narrow, during lever action legs press closely under the part to be removed min. - spindles legs a b c d ,0, M x 1, x 0 M1 x 1, x ,2 2,9 2

31 Pullers, 2- and -arm sturdy design, adjustable legs, during lever action legs press closely under the part to be removed Puller with Grease- Hydraulic- Spindle -H page 0 more power with Grease- Hydraulic- Spindle 2-arm min. - spindles legs a b c d ,,, M x M x 1, x 0 M1 x 1, x 2 G 1/2 x x 0 G 1/2 x x 0 G 1/2 x x 0 G 1/2 x x 0 G 1/2 x x 0 G 1/2 x x 0 G 1/2 x x , 1,2 2,,,1,,9 7,0, 11,0 -arm min. - spindles legs a b c d ,0,0, M x M x 1, x 0 M1 x 1, x 2 G 1/2 x x 0 G 1/2 x x 0 G 1/2 x x 0 G 1/2 x x 0 G 1/2 x x 0 G 1/2 x x 0 G 1/2 x x , 1,7,9 7,,, 9,,0 11, 1,0 fitting Grease-Hydraulic up to page 29

32 1 Mini-Pullers, 2-arm sturdy design, adjustable legs, during lever action legs press closely under the part to be removed, also for windscreen-wiper-arms for medium trucks and heavy trucks T min spindles M x M x legs a b c d 1, 2,2, 7 1, 0,2 0,2 1 - B Pullers, -arm with Spread-Adjuster self centering min. - spindles legs a b c d 1 - B 1 - B 1 - B ,,0, M x M x M x 1 1 1, 0, 0, 0, 1 - S Pullers, -arm with Slide Haer with Spread-Adjuster self centering adapterthread M min. - legs a b c d 1 - S 1 - S 1 - S ,,0, 1 1 1, 1, 1,7 2,0

33 1-1 Mini-Pullers, 2-arm self centering, during lever action legs press closely under the part to be removed min. - spindles legs a b c d / ,0 1,2 2,0 M x M x M x 1 1 1, 0,1 0,2 0, 1 - Mini-Pullers, -arm self centering, during lever action legs press closely under the part to be removed min. - spindles legs a b c d / ,2 1, 2, M x M x M x 1 1 1, 0,2 0, 0, 1

34 Universal-Windscreen-Wiper-Arm-Puller-Set 2 - SN Universal-Windscreen-Wiper-Arm-Puller-Set in box for approx. wipers, 0 cars, make of cars for cars and trucks Contents: grippers 2-G1 to -G 1 drive - B - ( beam, spindle ) 2-B 1 spindle-cap 2-D1 1 hollow-cap 2-D2 for wipers with water-nozzle in centre of the hub 1 spindle-extension NEU 2-D 1 puller 2-U1 with Krallex-legs and leg-spanner 2 special-legs 2U1SP SN 2,2 Cars: Audi, Alfa-Romeo, BMW, Chrysler-Jeep, Citroen, Chevrolet-Daewoo, Daihatsu, Fiat, Ford, Honda, Hyundai, Jaguar, KIA, Land Rover, Mazda, MG-Rover, MB, Mitsubishi, Nissan, Opel, Peugeot, Porsche, Renault, Saab, Seat, Skoda, Smart, Suzuki, Toyota, Volvo, VW... Trucks: MAN, MB, Scania... Application-table for 2 - SN on request Puller-Sets for any make of cars and types available Component parts for individual combinations - for make of cars and types - for wipers front ( right / left ) and back Application-table on request Grippers 2-G1 2-G2 2-G 2-G 2-G 2-G 2-G7 2-G drive - H - 2-H body with slide haer drive - B - 2-B body with spindle 2-D1 spindle-cap 2-D2 hollow-cap for wiper with water-nozzle in the centre 2-D spindleextension 2-U1 puller with Krallex-legs and leg-spanner 2U1SP-0 special-legs narrow body 2

35 Pullers, 2- and -arm self centering 2-arm -1 - min. - spindles legs a b c d ,,0, M x 1 x 90 M x 1 x 1 M x 1, x , , 0, 0,1 -arm ,,0, M x 1 x 90 M x 1 x 1 M x 1, x , , 0, 0,0 Pullers, 2- and -arm self centering Pullers, -arm with Spread-Adjuster self centering 1-B page -1-2-arm min. - spindles legs a b c d ,,0,,0 M x 1, x M x 1, x 19 M1 x 1, x 2 M x 2 x , 1, 2,00,0 -arm ,,0,,0 M x 1, x M x 1, x 19 M1 x 1, x 2 M x 2 x ,91 1,9 2,0,

36 Flange Type Axle Puller with Slide Haer adapterthread for bolt haer haer rod weight 1 - to 0 x 1,7 Universal-Wheel-Hub-Pullers 1 x M1 x 1,,7-1- spindles leg-tip hole for bolt to 2 to 2 to legs legs legs G / x x 2 G / x x 2 G / x x ,,, to 0 to 0 to legs legs legs G / x x 2 G / x x 2 G / x x ,,1, - M Universal-Puller, -arm sturdy design for heavy duty work, exchangeable legs for more reach, legs are always parallel gripping Beam-Arms are radially adjustable more power with Hydraulics min. - - M spindles legs a b c d 0 1 G 1 x 11 x , Legs ( = pieces ) - M - 0 M 0-0 M 0-00 M 00 - SP M adjustable 7 to 7 for -M -M -M -M -M , 9,0 11,0,,0 fitting Oil-Hydraulics up to page 2 fitting Grease-Hydraulic up to page

37 Universal-Spring-Compressors, also for MacPherson with safety guard, (as per SZGI PfG 9/.92) Release + Push Out Set for Four-guide-rod front axle: Audi, VW, Quattros for spring for spring S1 opening 1 opening S P /-PK page -S0/ - S2 page 1-S1 page 1-S2 page Ball Joint Separators Fork Type opening opening opening opening opening page 1-2 page 1- page 1- page 1- page Ball Joint Extractors opening opening opening opening opening opening Universal Ball Joint Extractors for cars medium trucks Ball Joint Extractors / - Sets for cars medium trucks Ball Joint Extractors for vans medium trucks t / KN 17-1 page page 0 opening 1-1 page page opening 17- page 2/2/ 1-K page T page page opening opening 19- page P page 9 opening 19-2P page Pullers for chassis of passenger cars and trucks Ball Joint Extractors for heavy trucks busses low floor busses opening 11 t / KN 19- page 1 Pullers for chassis of passenger cars and trucks

38 Spring-Compressors - P Universal-Spring-Compressor with safety guard - to remove coil springs quickly and safe min. - A A Instructions for use: Hook the spring tensions into position on opposite sides of the spring to cover as many turns as possible. Using a spanner or impact wrench, tighten the 19 spindle driver heads alternately. Install the new coil spring. Using the drive heads alternately, release the tension on the spring evenly. vehicles with unladen weight of The spring-compressor meets the requirements of the Safety regulations for vehicle maintenance (SZGI PfG 9/.9) working range spindles - P , M1 x 2 x , Universal-Spring-Compressor with Plastic-Coated Hooks with safety guard - PK , M1 x 2 x , - S Universal-Spring-Compressors with safety guard - to remove coil springs quickly and safe A Instructions for use: Hook the spring tensions into position on opposite sides of the spring to cover as many turns as possible. Using a spanner or impact wrench, tighten the 19 spindle driver heads alternately. Install the new coil spring. Using the drive heads alternately, release the tension on the spring evenly. The spring-compressor meets the requirements of the Safety regulations for vehicle maintenance (SZGI PfG 9/.9) min. - A vehicles with unladen weight of working range spindles - S0 - S1 - S , 1, 1, M1 x 20 M1 x 0 M1 x 0 2, 2, 2,9 Universal-Spring-Compressors with Plastic-Coated Hooks with safety guard - SK 0 - SK 1 - SK , 1, 1, M1 x 20 M1 x 0 M1 x 0 2, 2,9,0

39 Ball Joint Extractors for cars, medium trucks 1 A Ball Joint Extractors A C C 1-1 for Audi, Alfa-Romeo, BMW, Citroen, Fiat, Ford, Honda, MB, Opel, Peugeot, Renault, Saab, Seat, Skoda, Volvo, VW for Audi-A, -A, -A, VW-Passat, Opel-Movano for Ducato from 199, MB-Sprinter, VW-LT from A opening C spindles M1 x 1, x 0 M1 x 1, x 0 M1 x 1, x , 0, 0,9 1 - K Ball Joint Extractor Set in box for cars and medium trucks A opening 1 - K 2 / 2 / / / C contents 1-1, 1-2, 1-2,9 1 - N1 A Ball Joint Extractor B C A opening C B spindles 1 - N1 2 0 M x 1, x 0 0, 7

40 Ball Joint Extractors for cars, medium trucks, trucks 1 - S A Release + Push Out Set Release tool 1-S1 Push out tool 1-S2 B Release + Push Out Set B A to release and remove the linkage-stub attachment screw from the wheel-bearing shell of Four-guide-rod front axle of: Audi-A, -A, -A, all types of Quattros, VW-Passat, Skoda-Superb contents A B opening spindles 1 - S Release tool 1-S1 Push out tool 1-S M x 1, x 0 M9 x 1, x 1 1,7 Spare parts 1 - S1 Release tool 1 1 M x 1, x 0 1,1 1 - S2 Push out tool 90 M9 x 1, x 1 0, 1 Ball Joint Separators Fork Type A opening L length L A ,9 0,9 1,1 1, 1, 17 Ball Joint Extractors B C A A opening for VW-Bus T ( Ball joint at top cross steerage ) 17 - T C B spindles M x 1, x 0 M1 x 1, x 0 M1 x 1, x 7 G 1/2 x x 1 G / x x , 0,7 1,0 2,1 2, 20 G 1/2 x x 1 2,1

41 Ball Joint Extractors for cars, medium trucks 1-1 Universal Ball Joint Extractor adjustable A opening C height A C for cars: Audi, Alfa-Romeo, BMW, Citroen, Fiat, Ford, Honda, MB, Opel, Peugeot, Renault, Saab, Seat, Skoda, Volvo, VW pin adjustable spindle pressure spindle 70, M x 1, x M x 1, x 19 0,9 19-1P 19-2P Universal Ball Joint Extractors adjustable 19-1P A C for cars, medium trucks: Audi, Alfa-Romeo, BMW, Citroen, Fiat, Ford, Honda, MB, Opel, Peugeot, Renault, Saab, Seat, Skoda, Volvo, VW also for Aluminium - undercarriage at Audi, BMW, Porsche A 19-2P C A opening C height pressure spindle 19-1P 19-2P ,, M1 x 1, x 70 M1 x 1, x 90 1, 1, Info: Ball Joint Extractor Set 1-K in box for cars, vans and medium trucks page 7 9

42 Ball Joint Extractor for vans, medium trucks 19 - Ball Joint Extractor adjustable, mechanical tested by truck workshops for heavy duty work Grease-Hydraulic Oil-Hydraulic Grease-Hydraulic Oil-Hydraulic anvil A C opening height C A 19 - H Ball Joint Extractor adjustable with Grease-Hydraulic-Spindle t ( KN ) for bolts - thread UN-1 1/2 x H 90 HO19 - t ( KN ) HO19 - HM19 - HZ - pressure spindle adjusting spindle 19-H A C HM19- A opening C height A C for vans and medium trucks: MB Atego up to t MAN M0 Iveco Renault Scania Volvo DAF Spindle / anvil for reversible use Anvil adjustable and for tightening for bolts - Instructions for use: Insert the extractor between the ball cup and steering arm, adjust lever parallel to the fork, tighten with anvil and turn the spindle or activate hydraulic to remove. adjusting spindle M1 x 1, x 0 G1/2 x x 1,7 Grease-Hydraulic-Spindle page 90 Extractor - WITHOUT - Hydraulic-Cylinder 90 Extractor - WITH - Hydraulic-Cylinder HZ - t / KN cylinder for handpumps stroke 11, height:, thread / - 1 NPT 90 pressure spindle Ball Joint Extractor adjustable without or with Oil-Hydraulic-Cylinder for bolts -,7,,1 1, fitting Oil-Hydraulics up to page 2 fitting Grease-Hydraulic up to page

43 Ball Joint Extractor for heavy trucks, busses 19 - Ball Joint Extractor adjustable, mechanical tested by truck workshops for heavy duty work anvil adjusting spindle pressure spindle C A for heavy trucks, busses, low floor busses: MB ACTROS, Atego from 1 t, SK, O, -N, -GN (Nflb.) MAN F0, TG, A2, low floor busses Iveco Euro-Star, -Tech, Turbo-Star Renault Scania and, Icarus Volvo DAF Spindle / anvil for reversible use Anvil adjustable and for tightening 11 for bolts - Instructions for use: Insert the extractor between the ball cup and steering arm, adjust lever parallel to the fork, tighten with anvil and turn the spindle or activate hydraulic to remove. A opening C height adjusting spindle pressure spindle M2 x 1, x G/ x x 1, 19 - H t ( KN ) 19 - H 11 HO19 - t ( KN ) HM19- HO19 - HM19 - HZ - HZ - A opening 19-H C height t / KN cylinder for handpumps t / KN cylinder for handpumps A C Ball Joint Extractor adjustable with Grease-Hydraulic-Spindle for bolts - thread UN-1 1/2 x 1 Grease-Hydraulic-Spindle page Ball Joint Extractor adjustable without or with Oil-Hydraulic-Cylinder for bolts - C A Extractor - WITHOUT - Hydraulic-Cylinder Extractor - WITH - Hydraulic-Cylinder HZ - stroke 11, height, thread / - 1 NPT stroke 11, height 1, thread / - 1 NPT 7,0,0 7, 1, 2, Oil-Hydraulic Grease-Hydraulic fitting Oil-Hydraulics up to page 2 fitting Grease-Hydraulic up to page 1

44 0 Separators A A for pullers G adapter-thread for puller G adapterthread zu 2 Instructions for use: 1. Tapered knife edges of separator 0 fit behind bearing and remove by tightening both nuts in turn 2. Turn tie rods of device 2 into adapterthread of separator 0. Pull with centre spindle of device 2 / slide rods in combination with puller M M M 1 M x 1, M x 1, M 2 x 1, M x 0 M x 1 M1 x 1, x 10 M x 1, x 0 M2 x 1, x M2 x 1, x , 0,7 1,9,2,0 1, 2 Pullers for Separators tie rod more power with Hydraulics G adapter-thread for separators G adapterthread zu 0 spindles tie rod M M M 1 M x 1, M x 1, M 2 x 1, , M x 1, x 0 M x 1, x 0 G 1/2 x x 2 G 1/2 x x 2 G / x x 20 G 1 x 11 x 70 M x M x M1 x 20 M x 1, x 70 M x 1, x 70 M2 x 1, x 0, 1,1 2,7,2, 1,7 Extensions for Tie Rods for Pullers 2 ( = 1 pair ) extension plus for pullers G adapter-thread for 0 M M M 1 M x 1, M x 1, M 2 x 1, extensionmeasures M x lg M x lg M1 x lg M x 1, x lg M x 1, x lg M2 x 1, x lg 0,2 0,2 0, 0,7 0,7 2,7 2 fitting Oil-Hydraulics up to page 2 fitting Grease-Hydraulic up to page

45 S Separator- / Puller Sets in box -2 contents S / pieces: 0-0, 2-0, 2-00 pieces: 0-1, 2-1, 2- pieces: 0-2, 2-2, 2- pieces: 0-, 2-, 2- pieces: 0-, 2-, 2- pieces: 0-0, 0-1, 2-1, 2- pieces: -1, -2, 1-, 2-0, -1, 0-2 2,,0 7,, 29,0 2, 1,0 0 Internal Extractor- / Puller Sets in box 0-N 0-G min. - contents 0 - G 0 - K 0 - N pieces: 1-1A, -2A, -A, -A, -A, -A, -E7, -E, 2-1, -, -1, -2, 1-1, pieces: 1-1A, -2A, -A, -A, -A, -A, 2-1, -1, 1-1, pieces: 1-1A, -2A, -A, -A, -A, -A, -E7, 2-1, -2, -1, -2, 1-1,,0 7, 1,

46 12 Stearing Wheel Puller, -arm with ring min spindle 0 70 M x 1, x 0 1,9 Stearing Wheel Puller, 2-arm with short and long legs and spindle cap min. - spindle leg a b c d N1 for Audi, VW Dieselmotors TDI-, -, - Petrolmotors V, V from 9 2, M x 1, x 0, 11 7, 0,9 Puller Set for Cam Shaft Wheels with 2 standard-legs and 2 special-legs Leg-combinations for: wheels with spokes standard-leg standard-leg wheels with spokes - Cylinder-Motors - Cylinder-Motors standard-leg special-leg with opening: wheels with spokes - Cylinder-Motors Complete set standard-leg special-leg with opening: 2 min. - spindles 1 - N1 0 2, M x 1, x 0,9 Puller Chuck for inner rings of ball bearings min. - spindle tip spindle x M x 1, x 0 1,

47 1 - SN Passenger Car-V-Belt-Pulley Puller-Set in box supplementary with Groovehooks Combination-variants: variant Z : with Groovehooks short or long beam with groovehooks with short beam: with long beam: 0 to 1 to 2 NEW Groovehooks suit into the grooves of V-Belt Pulley variant A : for V-Belt Pulleys with thread holes short or long beam with screws min. - 0 / min. 9-2 exchangeable spindle extensions pressure plate short pressure plate medium + pressure plate long + 7 variant B : for V-Belt Pulleys without thread holes short or long beam with standard-legs and / or extensions min. 2 - / min SN 2 x standard-legs, reach with short screws 2 x extensions plus = up to reach with long screws Contents: 1 long beam 1 short beam 1 spindle pressure plates: short, medium, long 2 standard-legs 2 extensions 2 short screws 2 long screws 2 groovehooks 2,7

48 29 - S Bolt Extractor Sets in plastic box 29 - S 29 - S 0 Stud Pullers right- / left drive contents pieces pieces 0,11 0,2 drive , 0, 0, 1 Stud Puller right- / left drive large reach drive , Stud Puller Set in metal box drive / 1 piece puller - G for,,, 21 u. 1/2 1,2 Individual Parts /2 0, /2 0, /2 0, /2 0,2

49 - S1 Flange Spreader Set for spreading of pipe connecting DIN-flanges for renewal of gaskets and other maintenance work Flange Spreader Set ( = 1 pair ) see illustration for screws Instructions for use: Apply the spreaders diametrically. Place spreader jaws into the free bolt holes and tighten screws until spreader is in position. Tighten both screws simultan to wide gap evenly, permitting easy work between the flanges. Back off screws to allow flanges to rejoin accurately. spindle - S1 0-0 M1 to M2 M2 x 1, x 1 2, always used in pairs only 10 Individual Parts - 1-1H - 1SP 1 piece flange spreader 1 pair jaws 1 spindle M2 x1, with wedge 2, 0,9 0, Nut Splitters Grease-Hydraulic t -1 for nuts in quality class up to t -2 - additional inductive hardening of the cutting edge - rolled channel walls Instructions for use: 1. Place the cutting edge of chisel 90 to the flat of the nut and in line with the bolt shaft. Clamp it into position with the adjustable anvil. 2. Slowly, with interruptions, turn the pressure bolt into the splitter body to allow the hydraulic force to build up and take effect. A light tap with a haer on the anvil when under tension will increase the splitting effect. If stroke of the chisel is insufficient turn out the pressure bolt to its limit, readjust the anvil and retighten the pressure bolt.. After splitting the nut turn the pressure bolt back to its initial position ( A ). The chisel does not retract automatically, it must be pushed back ( B ). pressure bolt Grease-Hydraulic anvil B A min. - for nuts with thread pressure bolt anvil M to M M to M2 0 M x M x 1, x 0 M x 1, x M x 1, x 0 0, 2, 11 Nut Splitters, mechanical for nuts in quality class up to min. - for nuts with thread spindles to M to M to M1 to M2 0 0 M x M x 1, x M1 x 1, x M1 x 1, x 0 0, 0,2 0, 0,1 7

50 Pullers with Scissor-Action Arms self centering min. - spindles legs a b c d / / 0 1 / ,,, 1 M x M x 1, x 0 M x 1, x 2,,,,, , 0,9 1,1-1 SP Pullers with Scissor-Action Arms and with Special-Legs min. - spindles legs a b c d - 1 SP - SP / 1 / 1 1 1,0 2,0 M x M x 1, x 2,,,, , 1,0 Spindle Extensions - D1 - D plus plus + + for -1, -1SP -2, -, -SP1 0,0 0,0 Puller with Krallex-Legs Side Clamp Spindle cap for inner races of front wheel hubs min. - spindle leg a b c d ,2 M1 x 1, x , 1,9

51 Sets, Sales-Display, Workshop-Stands for Automotive, Industry - S Internal Extractor Sets page 9 0/1 Ball Bearing Extractor Set page 0 Puller- and Internal Extractor Sets page Ball Bearing Extractor Sets page 11 ES1-11 Krallex-Puller-Sets with Quick-Action-Nut EXTRA page 2 Workshop-Displays for automotive and industry Assortments on request 1-SN Passenger Car-V-Belt-Pulley Puller-Set page 2-SN Universal-Windscreen- Wiper-Arm-Puller-Set page 2 Separator- / Puller- Sets page Separator- / Puller Sets page -ST Sales-Display Workshop-Stand page 1, Workshop-Stands for automotive and industry Assortments on request 9

52 Spindles, Tie Rods B A A B Spindle - 1 S - 2 S - S - S Spindle M G 1 Spindle M G 1 - G 0-1 Spindle M G ,2 0, 1, 2,2 0,0 0,0 0,1 0,2 Spindle M 1 x 1, G 17-1 G G 2 1 Spindle G 1/2 x G G G 0-21 G - 21 Spindle G / x G 2 G - 2 G - L 2 A B ,2 0, 0, 0, 0, 0, 0, 1,0 1, 1,7 Spindle M x 1, G 17-1 G - HS G - 1 G 0 - GS-1S ,1 0,2 0,2 0, 0, Spindle G 1 x 11 G - G ,2 2, Spindle M 1 x 1, G G G ,1 0,1 0,2 Tie Rods G 2-1 G 2-2 G M M 1 M x 1, 0,2 0, 1,0 Universal-Puller-Set, 2-arm - One for all purposes - with different Leg-Sets 2 Standard-Legs 2 Krallex-Legs (, ) 2 Krallex-Legs special - FUSS - ( 2 ) 2 Krallex-Legs special - SCHAFT - ( ) min. - S-DIV - 0 2, 0

53 Assembly instruction for replacing mechanical spindle against Grease-Hydraulic-Spindle: Loosen first Depth Bolt, then unscrew entire cap ( largely), spindle body turn in pullers pivot, screw on cap again up to the notice and secure by tightening the Depth Bolt. Function: Puller be set, link up mechanically ( largely) and secure puller position. Pressure screw turn in press pivot. Impact screwdriver prohibited. If piston stroke is not sufficient for release, repeat processing steps: Turn back pressure screw, link up mechanically again and turn pressure screw again in press pivot. Grease-Hydraulic Safety reference: Secure puller position and tighten firmly all bolt connections before working, otherwise slipping danger. Grease-Hydraulic Program 1

54 Hydraulic Rams Nut Splitters, Grease-Hydraulic t / 0 KN 1 t / KN t / 0 KN stroke: 1t / KN stroke: 7 - M - M - M - M2-0 page 7-1 page 7-1 page 7-2 page 7 Puller-System, 2-arm Grease-Hydraulic-Spindles with Thread UN 1 1/2 x 1 t / 0 KN t / 0 KN page and -9 Ball Joint Extractor, adjustable for medium trucks opening 1-A1 page, 9 1-A2 page, A page, 9 1-A page, A page, H page Puller-System, -arm heavy trucks, low floor busses Grease-Hydraulic t / 0 KN -HS2 Thread G 1/2 x page 0-1-A page, A page, A page, F-2 page -2 1-A page, F-2, page A0 page, F1-2 page opening H page F1-2, page -HS Thread G / x page t / 0 KN / F- page / F-, page / F- page 1 t / KN -HS Thread G 1 x 11 page / 1 2 1/ 7 /0 -H/-H7 page 0 -H page -H1/-H page -H page 7 2 Pullers with Grease-Hydraulic-Spindles

55 1 - t / 0 KN Thread UN 1 1/2 x 1 Grease-Hydraulic-Spindle Info: Puller-System 1 page, stroke pressure-spindle pressure-spindle total length thread M x 90 1, 1 Grease-Hydraulic-Spindle t / 0 KN Thread UN 1 1/2 x 1 Info: Puller-System 1 page, 9 stroke pressure-spindle pressure-spindle total length thread M x 1, x 0 1, Spindle Extensions 1 - V V 1 - V plus + 0 plus + plus + for 1-, 1 1-, 1 1-, 1 0,1 0, 0, - HS 2 Grease-Hydraulic- Spindle t / 0 KN - HS 2 - HS t / 0 KN - HS Thread G 1/2 x total length M x 90 1,1 pressure-spindle Thread G / x pressure-spindle stroke stroke total length 0 0 M x 90 1, Grease-Hydraulic- Spindle pressure-spindle thread pressure-spindle thread Depth Bolt Depth Bolt Grease-Hydraulic - HS Grease-Hydraulic- Spindle Depth Bolt 1 t / KN Thread G 1 x 11 - HS stroke pressure-spindle pressure-spindle total length thread M x 1, x, Spindle Extensions - HD 1 - HD 2 - HD plus + 0 plus + plus + 0, 1, 1, Assembly instruction for replacing mechanical spindle against Grease-Hydraulic-Spindle: Loosen first Depth Bolt, then unscrew entire cap ( largely), spindle body turn in pullers pivot, screw on cap again up to the notice and secure by tightening the Depth Bolt. Function: Puller be set, link up mechanically ( largely) and secure puller position. Pressure screw turn in press pivot. Impact screwdriver prohibited. If piston stroke is not sufficient for release, repeat processing steps: Turn back pressure screw, link up mechanically again and turn pressure screw again in press pivot. Safety reference: Tighten firmly all bolt connections before working, otherwise slipping danger.

56 F - 2 F - 2, Universal-Pullers, 2-arm with Grease-Hydraulic-Spindle -HS2 Thread G 1/2 x Legs are parallel gripping and fixed on beam t / 0 KN min. - pressure-spindle pressure-spindle thread legs a b c d F - 2 F - 2, M x 90 M x ,, Legs ( = 1 pair ) F2-0 F2-0 2 for F-2 F-2, 1 1 1, 2, Grease-Hydraulic F1-2 F1-2, t / 0 KN Universal-Pullers, -arm with Grease-Hydraulic-Spindle -HS2 Thread G 1/2 x Legs are parallel gripping and fixed on beam min. - pressure-spindle pressure-spindle thread legs a b c d F1-2 F1-2, M x 90 M x ,0, Legs ( = pieces ) for F2-0 M F2-0 M 2 F1-2 F1-2, 1 1 2,, Assembly instruction for replacing mechanical spindle against Grease-Hydraulic-Spindle: Loosen first Depth Bolt, then unscrew entire cap ( largely), spindle body turn in pullers pivot, screw on cap again up to the notice and secure by tightening the Depth Bolt. Function: Puller be set, link up mechanically ( largely) and secure puller position. Pressure screw turn in press pivot. Impact screwdriver prohibited. If piston stroke is not sufficient for release, repeat processing steps: Turn back pressure screw, link up mechanically again and turn pressure screw again in press pivot. Safety reference: Tighten firmly all bolt connections before working, otherwise slipping danger.

57 F - F -, F - Universal-Pullers, 2-arm with Grease-Hydraulic-Spindle -HS Thread G / x Legs are parallel gripping and fixed on beam t / 0 KN min. - pressure-spindle pressure-spindle thread legs a b c d F - F -, F M x 90 M x 90 M x 90,0 9,0, Legs ( = 1 pair ) F - 1 F F - 0 F - 00 F - SP adjustable 2 to for F-, -, + - F-, -, + - F-, -, + - F-, -, + - F-, -, + - Assembly instruction for replacing mechanical spindle against Grease-Hydraulic-Spindle: Loosen first Depth Bolt, then unscrew entire cap ( largely), spindle body turn in pullers pivot, screw on cap again up to the notice and secure by tightening the Depth Bolt. Function: Puller be set, link up mechanically ( largely) and secure puller position. Pressure screw turn in press pivot. Impact screwdriver prohibited. If piston stroke is not sufficient for release, repeat processing steps: Turn back pressure screw, link up mechanically again and turn pressure screw again in press pivot. Safety reference: Tighten firmly all bolt connections before working, otherwise slipping danger.,,1, 7,, Grease-Hydraulic 1 t / KN Info: Universal-Puller, -arm + - H with Grease-Hydraulic-Spindle -HS Thread G 1 x 11 heavy execution Legs are parallel gripping and fixed on beam Beam-Arms are radially adjustable page 7

58 - H Universal-Puller, 2-arm with Grease-Hydraulic-Spindle -HS Thread G 1 x 11 Legs are parallel gripping and fixed on beam 1 t / KN min. - pressure-spindle pressure-spindle thread leg a b c d - H M x 1, x 0,0 Legs ( = 1 pair ) - 0 P - 0 P - 00 P - SP P adjustable 2 2 to for -H -H -H -H ,0 7,, 21, Grease-Hydraulic - H Universal-Pullers, -arm with Grease-Hydraulic-Spindle -HS Thread G 1 x 11 Legs are parallel gripping and fixed on beam 1 t / KN min. - pressure-spindle pressure-spindle thread legs a b c d - H 1 - H 2 - H M x 1, x M x 1, x M x 1, x,0 2, 2,0 Legs ( = pieces ) - 0 H 1-0 H 2-00 H - SP H adjustable 1 to for -H1, -H2, -H -H1, -H2, -H -H1, -H2, -H -H1, -H2, -H 7, 9, 11,7,7 Assembly instruction for replacing mechanical spindle against Grease-Hydraulic-Spindle: Loosen first Depth Bolt, then unscrew entire cap ( largely), spindle body turn in pullers pivot, screw on cap again up to the notice and secure by tightening the Depth Bolt. Function: Puller be set, link up mechanically ( largely) and secure puller position. Pressure screw turn in press pivot. Impact screwdriver prohibited. If piston stroke is not sufficient for release, repeat processing steps: Turn back pressure screw, link up mechanically again and turn pressure screw again in press pivot. Safety reference: Tighten firmly all bolt connections before working, otherwise slipping danger.

59 - H Universal-Puller, -arm + with Grease-Hydraulic-Spindle -HS Thread G 1 x 11 heavy execution Legs are parallel gripping and fixed on beam Special feature: Beam-arms are radially adjustable, exchangeable, -arm usable 1 t / KN min. - pressure-spindle pressure-spindle thread legs a b c d - H M x 1, x 7, Legs ( = pieces ) - 0 H 1-0 H 2-00 H - SP H adjustable to 0 for -H -H -H -H Assembly instruction for replacing mechanical spindle against Grease-Hydraulic-Spindle: Loosen first Depth Bolt, then unscrew entire cap ( largely), spindle body turn in pullers pivot, screw on cap again up to the notice and secure by tightening the Depth Bolt. Function: Puller be set, link up mechanically ( largely) and secure puller position. Pressure screw turn in press pivot. Impact screwdriver prohibited. If piston stroke is not sufficient for release, repeat processing steps: Turn back pressure screw, link up mechanically again and turn pressure screw again in press pivot. Safety reference: Tighten firmly all bolt connections before working, otherwise slipping danger ,0 11,0,,0 Grease-Hydraulic Ram Grease-Hydraulic for mechanical pullers Function: Puller be set together with Ram, link up mechanically and secure puller position. Pressure spindle turn in Ram pivot. Impact screwdriver prohibited. If piston stroke is not sufficient for release, repeat processing steps: Turn back pressure spindle, link up mechanically again and turn pressure spindle again in Ram pivot. t / 0 KN -0 1 t / KN -1 stroke pressure-spindle pressure-spindle thread M x 1, x 0 M x 1, x 0, 1, 7

60 Grease-Hydraulic-Spindles for Puller-System t / 0 KN Thread UN 1 1/2 x stoke pressure-spindle pressure-spindle thread thread 0 0 UN 1 1/2 x1 M x 90 1, 1 t / 0 KN Thread UN 1 1/2 x 1 1 Spindle Extensions 1 - V V 1 - V stoke pressure-spindle pressure-spindle thread thread 0 0 UN 1 1/2 x1 1 M x 1, x 0 1, for plus , 1 0,1 plus + 1-, 1 0, plus + 1-, 1 0, Function: Puller be set, link up mechanically ( largely) and secure puller position. Pressure screw turn in press pivot. Impact screwdriver prohibited. If piston stroke is not sufficient for release, repeat processing steps: Turn back pressure screw, link up mechanically again and turn pressure screw again in press pivot. Grease-Hydraulic 1 - A Puller-System, 2-arm with Grease-Hydraulic-Spindle 1- self-centering t / 0 KN 2-arm 1 - A A A 1 - A 1 - A min pressure spindle thread grease-hydraulik spindle UN 1 1/2 x 1 UN 1 1/2 x 1 UN 1 1/2 x 1 UN 1 1/2 x 1 UN 1 1/2 x 1 legs a b c d,,,1,0, Puller-System, -arm with Grease-Hydraulic-Spindle 1- self-centering t / 0 KN -arm min. - pressure spindle thread grease-hydraulik spindle legs a b c d 1 - A 1 - A 1 - A 1 - A 1 - A UN 1 1/2 x 1 UN 1 1/2 x 1 UN 1 1/2 x 1 UN 1 1/2 x 1 UN 1 1/2 x 1,,1,1,0,

61 Grease-Hydraulic-Spindle for Puller-System t / 0 KN t / 0 KN Thread UN 1 1/2 x 1 Individual Parts 1-A 11 Leg 1 piece for to suitable for pullers 1-A1, 1-A 0, 1-A Leg 1 piece for to 0 suitable for pullers 1-A2, 1-A 0, 1-A Leg 0 1 piece for to 190 suitable for pullers 1-A, 1-A 0,9 1-A Leg 1 piece for to 2 suitable for pullers 1-A, 1-A 0,9 1-A Leg 0 1 piece for to suitable for pullers 1-A, 1-A0 1,0 1-A 0 Puller, 2-arm , plus extension piece 1-V 1-A 2 1-A 70 1-A 72 1-A 7 1-A 0 Leg 2 1 piece with nut and washer suitable for puller 1-A0 Puller, 2-arm with tie rods plus extension piece 1-V Tie Rods 20 Extensions plus 0 1 pair with protection nut suitable for puller 1-A70 1 pair suitable for puller 1-A70 Internal Extractor ,, 2,1 1,7 2, Grease-Hydraulic 1-B 1 2-arm Beam without thread part, with bolts and nuts suitable for pullers 1-A1 to 1-A 0, 1-B -arm Beam without thread part, with bolts and nuts suitable for pullers 1-A to 1-A0 0, 1-B 11 Thread Part for beam 1-B1, 1-B 0, 1-T Beam, 2-arm for pullers 1-A0, 1-A70,1 1-V 0 Extension plus 0 for spindle 1 0,1 1-V Extension plus for spindle 1 0, 1-V Extension plus for spindle 1 0, 0-2 Separator - 11 for use with puller 1-A70 1,9 0- Separator - 1 for use with puller 1-A70,2 Sets on request 9

62 - H Pullers, -arm with Grease-Hydraulic-Spindle -HS Thread G 1 x 11 heavy execution Legs are vertically adjustable During lever action legs press closely under the part to be removed 1 t / KN min. - pressurespindle pressure-spindle thread legs a b c d Grease-Hydraulic - H - H - H - H - H 7 Legs ( = pieces ) - LH - LH - LH - LH - LH for -H, -H, -H, -H, -H7 -H, -H, -H, -H, -H7 -H, -H, -H, -H, -H7 -H, -H, -H, -H, -H7 -H, -H, -H, -H, -H7 M x 1, x M x 1, x M x 1, x M x 1, x M x 1, x,,,0, 1,0,7,0,,0, Assembly instruction for replacing mechanical spindle against Grease-Hydraulic-Spindle: Loosen first Depth Bolt, then unscrew entire cap ( largely), spindle body turn in pullers pivot, screw on cap again up to the notice and secure by tightening the Depth Bolt. Function: Puller be set, link up mechanically ( largely) and secure puller position. Pressure screw turn in press pivot. Impact screwdriver prohibited. If piston stroke is not sufficient for release, repeat processing steps: Turn back pressure screw, link up mechanically again and turn pressure screw again in press pivot. Safety reference: Tighten firmly all bolt connections before working, otherwise slipping danger. 1 t / KN Info: Universal-Puller, -arm + - H with Grease-Hydraulic-Spindle -HS Thread G 1 x 11 heavy execution Legs are parallel gripping and fixed on beam Beam-Arms are radially adjustable page 7 0

63 Oil-H -Hydrauli ydraulic Program Tighten collar firmly before working, otherwise slipping danger. Beam-Arms are - radially adjustable - exchangeable - expandable to four arms Safety reference: Secure puller position and tighten firmly all bolt connections before working, otherwise slipping danger. Oil-Hydraulic 1

64 Pumps, mech., pneum., electrical Hydraulic Cylinders, Hollow Piston Cylinders pressure 700 bar pressure 700 bar pressure 700 bar pressure 700 bar HP-1 HP-2 HP- ( manometer 1, m hose couplings ) page HZ-0 t / KN HZ-1 1t / KN HZ- t / KN HZ- t / KN HZ-11 t / 0KN page page page HZ-2 t / KN HZ- t / 0KN HZ- 0t / 00KN 2-arm -arm - 2 to pressure 700 bar page t / KN HY - 1 t / KN HY -1 t / 0 KN HY to 00 pressure 700 bar page 7 t / KN HY 11-1 t / KN HY 11-1 t / 0 KN HY 11-2-arm -arm t / KN pressure 700 bar HY - page t / 0 KN pressure 700 bar HY - page 0 t / 00 KN pressure 700 bar HY -0 page t / KN pressure 700 bar HY - page 9 t / 0 KN pressure 700 bar HY - page 9 0 t / 00 KN pressure 700 bar HY -0 page 9 -arm to 00 to 00 1 t / KN pressure 700 bar t / 0 KN pressure 700 bar HY -1 page 70 HY - page 70 -arm + Ball Joint Extractor, adjustable for medium trucks Opening Oil-Hydraulic -arm t / KN pressure 700 bar HY 1- page 72 1 t / KN pressure 700 bar HY -1 page t / 0 KN pressure 700 bar HY 1- page 72 t / 0 KN pressure 700 bar HY - page t / 00 KN pressure 700 bar HY 1-0 page 72 heavy trucks, low floor busses 90 t / KN pressure 700 bar HM19- page Opening 11 t / KN pressure 700 bar HM19- page 1 2 Oil-Hydraulic-Pullers, Pumps, Cylinders, Hollow Pistons

65 HP - 1 Hydraulic Hand Pump single speed pump for use with single acting cylinders, features a finger tip control valve for instant release or pumping action, with internal relief to protect circuit components, usable reservoir : cm = 0, litre, handle effort approx: 0 kp with manometer 1, m high pressure hose with couplings pressure: 700 bar connecting thread volume per stroke measurements fitting cylinders HP - 1 /-1 NPT 2,2 cm L B H 119 HZ-0, HZ-1, HZ-2, HZ-, HZ-, HZ-, HZ-11, HZ- with oil 9,0 HP - 2 Hydraulic Pump, pneumatic operates on 1,7 to, bar shop air, for use with single acting cylinders, with internal relief to protect circuit components, usable reservoir : 1 cm = 2,01 litre with manometer 1, m high pressure hose with couplings pressure: 700 bar connecting thread volume per stroke measurements fitting cylinders HP - 2 /-1 NPT 0, at bar 0,1 at 700 bar L B 0 H HZ-0, HZ-1, HZ-2, HZ-, HZ-, HZ-, HZ-11, HZ- with oil 11,0 HP - pressure: 700 bar connecting thread volume litre / minute Hydraulic Pump, electrical double speed pump for use with single acting cylinders, usable reservoir : 1900 cm = 1,9 litre motor: 0,7 kw - 0/2 Volt, 0/0 Hertz, single phase (,2 Ampere ) / 2 way valve ( push, stop and back ) with m remote control first step bar second step 700 bar with manometer 1, m high pressure hose with couplings measurements fitting cylinders Oil-Hydraulic HP - /-1 NPT 1. step:,1 2. step: 0,2 L 2 B 2 H 2 HZ-0, HZ-1, HZ-2, HZ-, HZ-, HZ-, HZ-11, HZ- with oil 11,0

66 HZ - 0 G Hydraulic Cylinder single acting with spring return high quality alloyed steel exchangeable piston cap necessary min. oil volume: cm = 0, litre t / KN pressure: 700 bar stroke G thread hose / coupling connecting thread measurements cylinder / length fitting pumps HZ UNC 2 1/ x / -1 NPT 27 / HP-1, HP-2, HP-, HZ - 1 G Hydraulic Cylinder single acting with spring return high quality alloyed steel exchangeable piston cap necessary min. oil volume: cm = 0, litre 1 t / KN pressure: 700 bar stroke G thread hose / coupling connecting thread measurements cylinder / length fitting pumps HZ - 1 M x 2 / -1 NPT 1 / 2 HP-1, HP-2, HP- 7,0 HZ - 11 G Spindle Hydraulic Cylinder single acting with spring return necessary min. oil volume: 0 cm = 0, litre t / 0 KN pressure: 700 bar stroke G thread hose / coupling connecting thread measurements length fitting pumps HZ G 1 x 11 / -1 NPT 0 HP-1, HP-2, HP-, Oil-Hydraulic HZ - HZ - t / KN t / KN stroke pressure: 700 bar hose / coupling thread Flat-Cylinders single acting with spring return min. oil volume: cm / litre measurements cylinder fitting pumps HZ - HZ - 11 t / KN t / KN / -1 NPT / -1 NPT 1 / 0,01 2 / 0, HP-1, HP-2, HP- HP-1, HP-2, HP- 1, 2,

67 HZ - 2 G Hydraulic Hollow Piston Cylinder with Spindle single acting with spring return the nickelplated middle tube for a long life necessary min. oil volume: cm = 0, litre for pressing and dragging 70 t / KN pressure: 700 bar strocke G spindle-thread hose / coupling connecting thread measurements cylinder spindle fitting pumps HZ UNC 1 - / - 1 NPT 70 HP-1, HP-2, HP-, HZ - G Hydraulic Hollow Piston Cylinder with Spindle single acting with spring return the nickelplated middle tube for a long life necessary min. oil volume: 29 cm = 0,29 litre for pressing and dragging 790 t / 0 KN pressure: 700 bar strocke G spindle-thread hose / coupling connecting thread measurements cylinder spindle fitting pumps HZ - UNC 1 1/ -7 / - 1 NPT 790 HP-1, HP-2, HP- 1,2 HZ - Hydraulic Hollow Piston Cylinder with Spindle single acting with spring return the nickelplated middle tube for a long life necessary min. oil volume: 2 cm = 0,2 litre for pressing and dragging G 27 0 t / 00 KN pressure: 700 bar 97 Oil-Hydraulic strocke G spindle-thread hose / coupling connecting thread measurements cylinder spindle fitting pumps HZ - 7 UNS 1 / - 1/2 / - 1 NPT HP-1, HP-2, HP-,

68 HY Universal-Pullers, 2-arm Legs are parallel gripping Safety reference: Before pulling make sure that all screws and nuts are fastened HY- HY-1 t / KN pressure: 700 bar HY- stroke Puller HY - HM - HO - Individual Part H Legs see below 1 t / KN 2 with Hydraulic Cylinder HZ-0 UNC 2 1/ x ( page ) Hand Pump HP-1 ( page ) with manometer, 1,0 1, m hose with couplings 2 with Hydraulic Cylinder HZ-0 UNC 2 1/ x ( page ),0 2 without hydraulic parts,0 pressure: 700 bar 1 beam for HY-, HM-, HO- 1,0 stroke Puller HY - 1 HM - 1 HO with Hydraulic Cylinder HZ-1 Mx2 ( page ) Hand Pump HP-1 ( page ) with manometer,,0 1, m hose with couplings 2 2 with Hydraulic Cylinder HZ-1 Mx2 ( page ) without hydraulic parts 2,0 19,0 Individual Part H Legs see below 1 beam for HY-1, HM-1, HO-1 1,0 t / 0 KN pressure: 700 bar stroke Puller Oil-Hydraulic HY - HM - HO - 2 with Hydraulic Cylinder HZ-11 G1 x11 ( page ) 0,0 Hand Pump HP-1 ( page ) with manometer, 1, m hose with couplings 2 with Hydraulic Cylinder HZ-11 G1 x11 ( page ) 2,0 2 without hydraulic parts 21, Individual Part H beam for HY-, HM-, HO- 1,0 Legs ( = 1 pair) for HY-, -1, -, HM-, -1, -, HO-, -1, - HY-, -1, -, HM-, -1, -, HO-, -1, - HY-, -1, -, HM-, -1, -, HO-, -1, - HY-, -1, -, HM-, -1, -, HO-, -1, -,,0 7,,

69 HY11 Pullers, -arm Legs are vertically adjustable Safety reference: Before pulling make sure that all screws and nuts are fastened HY11- HY11-1 HY11- t / KN pressure: 700 bar stroke Puller HY11 - HM11 - HO 11-0 with Hydraulic Cylinder HZ-0 UNC 2 1/ x ( page ) Hand Pump HP-1 ( page ) with manometer, 1 2,0 1,m hose with couplings 0 with Hydraulic Cylinder HZ-0 UNC 2 1/ x ( page ),0 0 without hydraulic parts 9, Individual Part H Legs see below 1 t / KN 1 beam with plates a. screws for HY11-, HM11-, HO11-,0 pressure: 700 bar stroke Puller HY11-1 HM11-1 HO with Hydraulic Cylinder HZ-1 Mx2 ( page ) Hand Pump HP-1 ( page ) with manometer, 2, 1,m hose with couplings 0 0 with Hydraulic Cylinder HZ-1 Mx2 ( page ) without hydraulic parts, 7, Individual Part H Legs see below t / 0 KN pressure: 700 bar 1 beam with plates a. screws for HY11-1, HM11-1, HO11-1 stroke Puller, HY11 - HM11 - HO 11 - Legs ( = pieces ) H H 0 00 H 0 00 H with Hydraulic Cylinder HZ-11 G1 x11 ( page ) 0,0 Hand Pump HP-1 ( page ) with manometer, 1,m hose with couplings 0 with Hydraulic Cylinder HZ-11 G1 x11 ( page ),0 0 without hydraulic parts, Individual Part H beam with plates a. screws for HY11-, HM11-, HO11-, for HY11-, -1, -, HM11-, -1, -, HO11-, -1, - HY11-, -1, -, HM11-, -1, -, HO11-, -1, - HY11-, -1, -, HM11-, -1, -, HO11-, -1, - HY11-, -1, -, HM11-, -1, -, HO11-, -1, -,0,,0, Oil-Hydraulic 7

70 HY Pullers, 2-arm Legs are vertically adjustable Safety reference: Before pulling make sure that all screws and nuts are fastened t / KN HY- pressure: 700 bar stroke Puller HY - HM - HO with Hollow Piston Cyl. HZ-2 UNC 1 - ( page ) Hand Pump HP-1 ( page ) with manometer, 9 1,1 1, m hose with couplings 290 with Hollow Piston Cyl. HZ-2 UNC 1 - ( page ),1 290 without hydraulic parts 11, Individual Parts H H beam with plates a. screws for HY-, HM-, HO- 1 leg for HY-, HM-, HO-,0, t / 0 KN pressure: 700 bar stroke Puller HY HM - HO with Hollow Piston Cyl. HZ- UNC 1 1/ - 7 ( page ) Hand Pump HP-1 ( page ) with manometer,,0 1, m hose with couplings 0 with Hollow Piston Cyl. HZ- UNC 1 1/ - 7 ( page ),0 0 without hydraulic parts,0 Individual Parts H H beam with plates a. screws for HY-, HM-, HO- 1 leg for HY-, HM-, HO-,0, Oil-Hydraulic 0 t / 00 KN stroke Puller HY HM - 0 HO pressure: 700 bar 700 with Hollow Piston Cyl. HZ- UNS 1 / - 1/2 ( page ) Hand Pump HP-1 ( page ) with manometer, 7,0 1, m hose with couplings 700 with Hollow Piston Cyl. HZ- UNS 1 / - 1/2 ( page ) 90, 700 without hydraulic parts 0,0 Individual Parts H 000 H beam with plates a. screws for HY-0, HM-0, HO-0 1 leg for HY-0, HM-0, HO-0 1,0,0

71 HY Pullers, -arm Legs are vertically adjustable Safety reference: Before pulling make sure that all screws and nuts are fastened t / KN pressure: 700 bar HY- stroke Puller HY - HM - HO with Hollow Piston Cyl. HZ-2 UNC 1 - ( page ) Hand Pump HP-1 ( page ) with manometer, 9, 1, m hose with couplings 290 with Hollow Piston Cyl. HZ-2 UNC 1 - ( page ), 290 without hydraulic parts,0 Individual Parts H H beam with plates a. screws for HY-, HM-, HO- 1 leg for HY-, HM-, HO- 7,0, t / 0 KN stroke Puller HY HM - HO pressure: 700 bar 0 with Hollow Piston Cyl. HZ- UNC 1 1/ - 7 ( page ) Hand Pump HP-1 ( page ) with manometer,,0 1, m hose with couplings 0 0 with Hollow Piston Cyl. HZ- UNC 1 1/ - 7 ( page ) without hydraulic parts,0,0 Individual Parts H H beam with plates a. screws for HY-, HM-, HO- 1 leg for HY-, HM-, HO- 11,, 0 t / 00 KN stroke Puller HY HM - 0 HO pressure: 700 bar 700 with Hollow Piston Cyl. HZ- UNS 1 / - 1/2 ( page ) 7 0,0 Hand Pump HP-1 ( page ) with manometer, 1, m hose with couplings 700 with Hollow Piston Cyl. HZ- UNS 1 / - 1/2 ( page ) 1, 700 without hydraulic parts 70,0 Oil-Hydraulic Individual Parts H H beam with plates a. screws for HY-0, HM-0, HO-0 1 leg for HY-0, HM-0, HO-0,0,0 9

72 HY - 1 Pullers, -arm + Legs are parallel gripping Special feature: Beam-arms are radially adjustable, exchangeable, -arm usable Safety reference: Before pulling make sure that all screws and nuts are fastened 1 t / KN pressure: 700 bar HY-1 stroke Puller HY HM - 1 HO with Hydraulic Cylinder HZ-1 Mx2 ( page ) 1,0 Hand Pump HP-1 ( page ) with manometer, 1, m hose with couplings with Hydraulic Cylinder HZ-1 Mx2 ( page ),0 without hydraulic parts,0 Individual Parts H H M - 0 M - 0 M - 00 M beam with brace ring for HY-1, HM-1, HO-1 1 beam-arm for HY-1, HM-1, HO-1 legs for HY-1, HM-1, HO-1 legs for HY-1, HM-1, HO-1 legs for HY-1, HM-1, HO-1 legs for HY-1, HM-1, HO-1,0 7,0, 9,0 11,0, HY - Pullers, -arm + Legs are parallel gripping Special feature: Beam-arms are radially adjustable, exchangeable, -arm usable t / 0 KN Safety reference: Before pulling make sure that all screws and nuts are fastened pressure: 700 bar HY- Oil-Hydraulic stroke Puller HY - HM - HO - Individual Parts H 000 H M - 0 M - 0 M - 00 M with Hydraulic Cylinder HZ-11 G1 x11 ( page ) 0,0 Hand Pump HP-1 ( page ) with manometer, 1, m hose with couplings with Hydraulic Cylinder HZ-11 G1 x11 ( page ) 7,0 without hydraulic parts, beam with brace ring for HY-, HM-, HO- 1 beam-arm for HY-, HM-, HO- legs for HY-, HM-, HO- legs for HY-, HM-, HO- legs for HY-, HM-, HO- legs for HY-, HM-, HO-, 7,0, 9,0 11,0, 70

73 HY - 1 Puller, -arm + Legs are vertically adjustable Special feature: Beam-arms are radially adjustable, exchangeable, -arm usable Safety reference: Before pulling make sure that all screws and nuts are fastened 1 t / KN pressure: 700 bar HY-1 stroke Puller HY HM - 1 HO with Hydraulic Cylinder HZ-1 Mx2 ( page ) 1,0 Hand Pump HP-1 ( page ) with manometer, 1, m hose with couplings with Hydraulic Cylinder HZ-1 Mx2 ( page ) 29,0 without hydraulic parts,0 Individual Parts H 000 H 001 H beam with brace ring for HY-1, HM-1, HO-1 1 beam-arm with plates a. screws for HY-1, HM-1,HO-1 1 leg for HY-1, HM-1, HO-1,0,0, HY - Pullers, -arm + Legs are vertically adjustable Special feature: Beam-arms are radially adjustable, exchangeable, -arm usable Safety reference: Before pulling make sure that all screws and nuts are fastened t / 0 KN stroke Puller HY - 00 HM - HO pressure: 700 bar HY- with Hydraulic Cylinder HZ-11 G1 x11 ( page ) Hand Pump HP-1 ( page ) with manometer, 0 7, 1, m hose with couplings with Hydraulic Cylinder HZ-11 G1 x11 ( page ) 2, without hydraulic parts 2,0 Oil-Hydraulic Individual Parts H H 001 H beam with brace ring for HY-, HM-, HO- 1 beam-arm with plates a. screws for HY-, HM-, HO- 1 leg for HY-, HM-, HO-,,0, 71

74 HY1 Pullers, -arm + Legs are vertically adjustable Special feature: Beam-arms are radially adjustable, exchangeable, -arm usable Safety reference: Before pulling make sure that all screws and nuts are fastened t / KN pressure: 700 bar HY1- stroke Puller HY1-00 HM1 - HO with Hollow Piston Cyl. HZ-2 UNC 1 - ( page ) Hand Pump HP-1 ( page ) with manometer, 9 7,0 1, m hose with couplings 0 with Hollow Piston Cyl. HZ-2 UNC 1 - ( page ),0 0 without hydraulic parts,0 Individual Parts H H H t / 0 KN pressure: 700 bar 1 beam with brace ring and flange for HY1-, HM1-, HO1-1 beam-arm with plates and screws for HY1-, HM1-, HO1-1 Leg for HY1-, HM1-, HO1-1,0,0, stroke Puller HY1-70 HM1 - HO with Hollow Piston Cyl. HZ- UNC 1 1/ - 7 ( page ) 7,0 Hand Pump HP-1 ( page ) with manometer, 1, m hose with couplings with Hollow Piston Cyl. HZ- UNC 1 1/ - 7 ( page ) 7,0 without hydraulic parts 2,0 Oil-Hydraulic Individual Parts H 000 H 001 H t / 00 KN stroke Puller HY1-0 0 HM1-0 HO pressure: 700 bar Individual Parts H 000 H 001 H beam with brace ring and flange for HY1-, HM1-, HO1-1 beam-arm with plates and screws for HY1-, HM1-, HO1-1 leg for HY1-, HM1-, HO1-0 with Hollow Piston Cyl. HZ- UNS 1 / - 1/2 ( page ) 7 1,0 Hand Pump HP-1 ( page ) with manometer, 1, m hose with couplings 0 with Hollow Piston Cyl. HZ- UNS 1 / - 1/2 ( page ) 7,0 0 without hydraulic parts,0 1 beam with brace ring and flange for HY1-0, HM1-0, HO1-0 1 beam-arm with plates and screws for HY1-0, HM1-0, HO1-0 1 leg for HY1-0, HM1-0, HO1-0,0,0,,0,0,0 72

75

76