Important Instructions

Transcription

1 Important Instructions Subject Use With Cabinet Hardmount Trunnion Replacement Cabinet Hardmount 8-60 Pound Washer-Extractors and Kits F77000, F7700, F7700, F7700, F7700, F7700, F9P and F9P WARNING This kit is to be installed in accordance with the manufacturer s instructions and all codes and requirements of the authority having jurisdiction. In Canada, this conversion/installation shall be carried out in accordance with the requirements of the provincial authorities having jurisdiction and in accordance with the requirements of the CAN/CGA-B9. and CAN/CGA- B9. installation code. Failure to follow instructions could result in serious injury, death or property damage. The qualified agency performing this work assumes all responsibility for this kit installation. W0R To reduce the risk of electric shock, fire, explosion, serious injury or death: Disconnect electric power to the machine before servicing. Never start the machine with any guards/panels removed. Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the machine is properly grounded. W6 Kit F77000 (*C8 -Speed/*C0 -Speed Models built through /6/06) consists of: - F60770 Trunnion - F79000 Gasket Kit 9 - F70 Shell Band Seal ft - F Shell Band Gasket - F00 RTV Sealant - F0 Fiber Locknut /-0 - F07 Flat Washer /, 9/x - F08 Screw /-0x - F8P Hardware Kit 6 - F09 Fiber Locknut /- 6 - F099 Screw /-x" 6 - F8 Flat Washer /,.x. - F880 Retaining Compound R Important Instructions Kit F7700 (*C8 -Speed/*C8 Variable Speed/*C0 -Speed Models built starting / 7/06/*C -Speed) consists of: - F6099 Trunnion - F79000 Gasket Kit 9 - F70 Shell Band Seal - F Shell Band Gasket ft - F00 RTV Sealant - F0 Fiber Locknut /-0 - F07 Flat Washer /, 9/x - F08 Screw /-0x - F8P Hardware Kit 6 - F09 Fiber Locknut /- 6 - F099 Screw /-x" 6 - F8 Flat Washer /,.x. - F880 Retaining Compound R Important Instructions (continued) RSPC P.O. Box 990 Ripon, WI Page of 8 Form No R December 008

2 Kit F7700 (*C7 -Speed/*C0 -Speed/ *C -Speed/*C0 -Speed/*C0 Variable Speed Models built through 0//07) consists of: - F60 Trunnion - F79000 Gasket Kit 9 - F70 Shell Band Seal - F Shell Band Gasket ft - F00 RTV Sealant - F0 Fiber Locknut /-0 - F07 Flat Washer /, 9/x - F08 Screw /-0x - F8P Hardware Kit 6 - F00 Fiber Locknut 9/6-6 - F0987 Screw 9/6-x- /" 6 - F Flat Washer 9/6,.78x - F880 Retaining Compound R Important Instructions Kit F7700 (*C7 Variable Speed/ *C -Speed/* Variable Speed/ *C0 - Speed/*C0 Variable Speed Models built starting 0//07) consists of: - F6077 Trunnion - F79000 Gasket Kit 9 - F70 Shell Band Seal - F Shell Band Gasket ft - F00 RTV Sealant - F0 Fiber Locknut /-0 - F07 Flat Washer /, 9/x - F08 Screw /-0x - F8P Hardware Kit 6 - F00 Fiber Locknut 9/6-6 - F0987 Screw 9/6-x- /" 6 - F Flat Washer 9/6,.78x - F880 Retaining Compound R Important Instructions Kit F7700 (*C0 -Speed) consists of: - F608 Trunnion - F79000 Gasket Kit 9 - F70 Shell Band Seal ft - F Shell Band Gasket - F00 RTV Sealant - F0 Fiber Locknut /-0 - F07 Flat Washer /, 9/x - F08 Screw /-0x - F8P Hardware Kit 6 - F00 Fiber Locknut 9/6-6 - F0987 Screw 9/6-x- /" 6 - F Flat Washer 9/6,.78x - F880 Retaining Compound R Important Instructions Kit F7700 (*C0 -Speed/*C0 Variable Speed/*C60 -Speed/*C60 Variable Speed) consists of: - F609 Trunnion - F79000 Gasket Kit 9 - F70 Shell Band Seal ft - F Shell Band Gasket - F00 RTV Sealant - F0 Fiber Locknut /-0 - F07 Flat Washer /, 9/x - F08 Screw /-0x - F8P Hardware Kit 6 - F00 Fiber Locknut 9/6-6 - F0987 Screw 9/6-x- /" 6 - F Flat Washer 9/6,.78x - F880 Retaining Compound R Important Instructions Page of 8 (-06-6R)

3 Trunnion Upgrade Kit F9P (*C8 and *C0 Models built through /6/06) consists of: - F80 Basket Assembly - F6099 Trunnion Assembly - F79000 Gasket Kit 9 F70 Shell Band Seal ft - F Shell Band Gasket - F00 RTV Sealant - F0 Fiber Locknut /-0 - F07 Flat Washer /, 9/x - F08 Screw /-0x - F8P Hardware Kit 6 -F09 Fiber Locknut /- 6 - F099 Screw /-x" 6 - F8 Flat Washer /,.x. - F880 Retaining Compound R Important Instructions Trunnion Upgrade Kit F9P (*C0 Models built through 0//07) consists of: - F8600 Basket Assembly - F6077 Trunnion Assembly - F79000 Gasket Kit 9 F70 Shell Band Seal ft - F Shell Band Gasket - F00 RTV Sealant - F0 Fiber Locknut /-0 - F07 Flat Washer /, 9/x - F08 Screw /-0x - F8P Hardware Kit 6 -F09 Fiber Locknut /- 6 - F099 Screw /-x" 6 - F8 Flat Washer /,.x. - F880 Retaining Compound R Important Instructions Additional Materials and Tools Needed: Short mm Allen Wrench Denatured Alcohol Emery Cloth Loctite 60 (Green) F60 Basket Pulley Puller Tool Rubber Mallet - Bolts (To insert in trunnion removal holes) Micrometer Tape Measure Penetrating Oil (i.e., WD0) Permanent Marker Long-Handled Socket Wrench with Socket Screwdriver Long mm Allen Wrench F707 M DP-60 Epoxy F609 Basket Puller Tool 0-0 Ft-lb Torque Wrench Sledge Hammer F006 Grease Cartridge Basket Insertion Adapter Tool 96P - *C8/*C0/*C 97P - *C7/*C0/*C/*C0 98P - *C0/*C60 0P Basket Insertion Guide Rod Tool Basket Puller Kit F *C8/*C0/*C F *C7/*C0/*C/*C0 F *C0/*C60 IMPORTANT: This kit must be installed by a qualified service person. IMPORTANT: When reference is made to directions (right or left) in this instruction, it is from operator s position facing front of machine. IMPORTANT: Minimum of two service technicians required to complete installation. Page of 8 (-06-6R)

4 Preparation Work. Clear area around and at the rear of the machine.. Open door.. Disconnect electrical power to machine.. Turn OFF hot and cold water inlet supply and remove hoses from machine.. Remove front panel and rear panel. Refer to Figure.. Remove shell band gasket. Refer to Figure. 6 7 CHM0K 8 CHM0K Front Panel Door Door Lock Cover Door Bezel Rear Panel Figure 6. Remove door lock cover and L-catch. 7. Remove nuts and lockwashers from door lock plate and remove door lock from shell front. 8. Disconnect door lock assembly. 9. Mark location, with permanent marker, of the shell front with relation to shell. This will be the position location for reassembly of the shell front and to ensure the door is level. 0. Mark location of shell band and bolt location where they meet shell. Door Assembly Shell Front with Door Bezel Shell Band Gasket Shell Band Basket 6 Seal Sleeve 7 Trunnion Assembly 8 Shell Figure. Remove shell front, door and door bezel assembly together. Refer to Figure. Page of 8 (-06-6R)

5 Removing Trunnion Assembly. Remove belt from motor and basket pulleys. Refer to Figure Remove key. 7. Using Basket Puller Tool, remove basket. 8. Remove 6 screws attaching trunnion to frame. 9. Insert screws (removed in Step 8) into the trunnion removal holes and torque evenly in a cross pattern to force trunnion from frame. Remove trunnion assembly from frame. 0. Remove burrs from shaft with fine emery cloth ( grit). When completed, clean shaft with a clean rag dipped in solvent and apply a film of WD-0.. Scrape off old sealant from shell back. Clean shell back with soap and water, if needed. Wipe area with denatured alcohol. Allow area to dry. Installing Trunnion Assembly. Inspect shaft and seal sleeve for excessive wear. Replace if necessary.. Apply F00 RTV Sealant to back of shell where trunnion will be installed. Amount should be sufficient to seal trunnion without causing excess sealant to contaminate main seals. Refer to Figure and Figure. Key Pulley Washer Bolt Belt 6 Motor CHM99K PHM99K Figure. Remove bolt and washer from end of shaft.. Remove basket pulley from shaft using F60 Basket Pulley Puller Tool and F609 Basket Puller Tool. a. Place F60 Basket Pulley Puller Tool behind pulley. b. Attach arms of F609 Basket Puller Tool to inside of F60 Basket Pulley Puller Tool and align center screw. c. Tighten center screw, pulling pulley off basket shaft. d. Mount F60 Basket Pulley Puller Tool arms against inside of frame and align center screw. e. Tighten center screw, pushing basket forward. Frame-Bearing Plate Shell Back RTV Sealant Figure CHM006K Page of 8 (-06-6R)

6 . Apply F880 Retaining Compound to part of trunnion that will fit inside frame-bearing plate hole. Refer to Figure Apply a /8 inch bead of F707 M DP-60 Epoxy to each screw around the entire screw shank / inch above screw head. Refer to Figure 6 7. From inside shell, insert screws into shell back and into frame bearing plate. Epoxy should expand /6 inch to /8 inch from screw head when it is pressed flush against the shell back. Refer to Figure 6. /6 in. to /8 in. 6 Shell Back Frame-Bearing Plate Retaining Compound (Pre-Applied at Manufacturer) Trunnion Assembly Grease (Pre-Applied at Manufacturer) 6 RTV Sealant 7 Retaining Compound (/8 Inch Bead) Figure. Clean 6 new screws (supplied with kit) with denatured alcohol and wipe dry. CHM008K / in. Screw M DP-60 Epoxy Shell Back Figure 6 CHM00K 8. Prevent epoxy from dripping into seal area. 9. Mount trunnion onto frame over screws inserted in Step. Insert 6 new flat washers (supplied with kit) onto screws. Apply Loctite 60 (green) to 6 new fiber locknuts (supplied with kit) and torque them alternately (criss-cross pattern) and in even increments onto screws. Torque *C8- machines to 7 Ft-Lb. Torque *C7-60 machines to 0 Ft-Lb. Page 6 of 8 (-06-6R)

7 Installing Basket NOTE: Steps 0 - must be completed within minutes of applying retaining compound due to cure time. 0. Apply grease liberally to basket seal collar and apply /8 inch bead F880 Retaining Compound to front bearing journal near the leading edge and to rear bearing journal. Refer to Figure Reinstall shell band with F70 Shell Band Seal and hardware, supplied with kit, in the o clock position, or the location marked in Step Check basket front to shell front centering alignment at the o clock, 6 o clock, 9 o clock, and o clock positions. Basket centering should be evenly spaced and should not vary by more than /8 inch. Refer to Figure 8. /8 in. minimum Retaining Compound Applied to Front Bearing Journal Retaining Compound Applied to Rear Bearing Journal Shaft Basket Grease Applied to Basket Seal Collar Figure 7 CHM09K. Attach Basket Insertion Adapter Tool (96P, 97P, or 98P) and 0P Basket Insertion Guide Rod Tool to shaft and insert basket into shell. Guide basket insertion tools and shaft through trunnion assembly. Basket Front Shell Front Figure 8 CHM0K If the alignment is off at the o clock position, remove or shell mounting washers from each side. Refer to Figure 9. If the alignment is off at the 6 o clock position, add or shell mounting washers to each side. Refer to Figure 9. If the alignment is off at the o clock or 9 o clock positions, adjust the shell to the right or left as needed. Refer to Figure 9. IMPORTANT: Avoid contact with seal lips.. Remove basket insertion tools.. Reinstall basket pulley and belt in the reverse order of removal. NOTE: It may be necessary to use Basket Puller Tool (F79800, F79800, or F79800) to pull in the basket fully.. Align pulley and check belt tension. Refer to Operation/Maintenance manual for belt tension and alignment specifications.. Install F Shell Band Gasket around shell seat. Add RTV sealant as needed to fill uneven spaces. 6. Reinstall shell front, door and door bezel assembly. Mounting Washers Figure 9 CHM0K Page 7 of 8 (-06-6R)

8 9. Using measurement recorded earlier, set shell to basket gap. Gap should be between /6 inch ( mm) to /8 inch (9. mm). Refer to Figure 0. /6 in. to /8 in. Reassembling Machine 0. Apply RTV sealant around shell front screw holes used to attach door lock assembly.. Reinstall door lock assembly and L-catch.. Reinstall door lock cover.. Reinstall front and back panels.. Restore power to machine and reconnect water lines.. Run machine through test cycle. NOTE: Excessive play, looseness or noise may indicate improper parts or assembly. 6. Check to verify water is not leaking at trunnion bolt locations or shell band seal. 7. Verify door lock operates properly. Refer to Operation/Maintenance manual for instructions on testing door lock. Basket Shell Front Figure 0 CHM00K NOTE: To decrease the gap, tap the inside of the basket lip toward the shell with a rubber mallet. Do not distort shell front as this may cause door seal leaks. Page 8 of 8 (-06-6R)