Precision Monolithic Low-Voltage CMOS Analog Switches

Transcription

1 G47L, G48L, G49L Precision Monolithic Low-Voltage MOS Analog Switches ESRIPTION The G47L, G48L, G49L are low voltage pin-for-pin compatible companion devices to the industry standard G47, G48, G49 with improved performance. Using BiMOS wafer fabrication technology allows the G47L, G48L, G49L to operate on single and dual supplies. Single supply voltage ranges from 3 V to 2 V while dual supply operation is recommended with ± 3 V to ± 6 V. ombining high speed (t ON : 28 ns), flat R ON over the analog signal range (6 ), minimal insertion lose (up to MHz), and excellent crosstalk and off-isolation performance (- 7 db at MHz), the G47L, G48L, G49L are ideally suited for audio and video signal switching. The G47L and G48L respond to opposite control logic as shown in the truth table. The G49L has an SPT configuration. FEATURES 2.7 thru 2 V single supply or ± 3- thru ± 6 dual supply Available On-resistance - R ON : 4 Fast switching - t ON : 28 ns Available - t OFF : 3 ns TTL, MOS compatible Low leakage: < pa Material categorization: For definitions of compliance please see /doc?9992 APPLIATIONS Precision automatic test equipment Precision data acquisition ommunication systems Battery powered systems omputer peripherals SSL, SLAM Audio and video signal routing BENEFITS Widest dynamic range Low signal errors and distortion Break-before-make switching action Simple interfacing FUNTIONAL BLOK IAGRAM AN P ONFIGURATION TRUTH TABLE G47L, G48L ual-in-line, MSOP-8 and SOI-8 N/NO 8 OM * 2 7 GN T op V iew * Not onnected Logic G47L G48L ON OFF OFF ON ORERG FORMATION (G47L, G48L) Temp. Range Package Part Number 8-Pin Narrow SOI 8-Pin MSOP G47LY G47LY-E3 G47LY-T G47LY-T-E3 G48LY G48LY-E3 G48LY-T G48LY-T-E3 G47LQ-T-E3 G48LQ-T-E3 G49L ual-in-line, MSOP-8 and SOI-8 OM 8 NO N 2 7 GN Top View TRUTH TABLE (G49L) Logic N NO ON OFF OFF ON ORERG FORMATION (G49L) Temp. Range Package Part Number G49LY G49LY-E3 8-Pin Narrow SOI - 4 to 8 G49LY-T G49LY-T-E3 8-Pin MSOP G49LQ-T-E3 * Pb containing terminations are not RoHS compliant, exemptions may apply ocument Number: 7763 S3-86-Rev. G, 9-Aug-3 THE PROUT ESRIBE HERE AN THIS OUMENT ARE SUBJET TO SPEIFI ISLAIMERS, SET FORTH AT /doc?9

2 G47L, G48L, G49L ABSOLUTE MAXIMUM RATGS Parameter Limit Unit to -.3 to 3 GN to 7 (GN -.3) to () +.3 V I N, OM, N, NO a -.3 to ( +.3) or 3 ma, whichever occurs first ontinuous urrent (Any Terminal) 3 Peak urrent, S or (Pulsed ms, % uty ycle) ma Storage Temperature (AK, Q, Y Suffix) - 6 to Power issipation (Packages) b 8-Pin SOI c 4 8-Pin MSOP c 32 8-Pin erip d 6 Notes: a. Signals on N, NO, OM, or exceeding or will be clamped by internal diodes. Limit forward diode current to maximum current ratings. b. All leads welded or soldered to P board. c. erate 6. mw/ above 2. d. erate 2 mw/ above 7. SPEIFIATIONS (Single Supply 2 V) Parameter Symbol Test onditions Unless Otherwise Specified = 2 V, = V = V, V = 2.4 V,.8 V f Temp. b Typ. c mw A Suffix Limits Suffix Limits - to 2-4 to 8 Min. d Max. d Min. d Max. d Analog Switch Analog Signal Range e V ANALOG 2 2 V On-Resistance R =.8 V, = V ON I NO, I N = ma, V OM = 2 V / 9 V Switch Off Leakage urrent I NO(off) I N(off) I OM(off) V OM = V / V V NO, V N = V / V hannel On Leakage urrent I OM(on) V NO, V N = V OM = V / V igital ontrol Input urrent I L or I H µa ynamic haracteristics Turn-On Time t ON R L = 3, L = 3 pf Turn-Off Time t OFF V NO, V N = V, see figure ns G49L only, V Break-Before-Make Time elay t N, V NO = V R L = 3, L = 3 pf 3 harge Injection e Q J V g = V, R g =, L = nf p Off-Isolation e OIRR - 7 R L =, L = pf, f = MHz hannel-to-hannel rosstalk e X TALK - 7 db Source Off apacitance e NO(off) N(off) V = or, f = MHz pf hannel-on apacitance e ON Power Supplies Positive Supply urrent I+ Negative Supply urrent I- V = or Logic Supply urrent I L Ground urrent I GN Unit na µa 2 ocument Number: 7763 S3-86-Rev. G, 9-Aug-3 THE PROUT ESRIBE HERE AN THIS OUMENT ARE SUBJET TO SPEIFI ISLAIMERS, SET FORTH AT /doc?9

3 G47L, G48L, G49L SPEIFIATIONS (ual Supply ± V) Parameter Symbol Test onditions Unless Otherwise Specified = V, = - V = V, V = 2.4 V,.8 V f Temp. b Typ. c A Suffix Limits Suffix Limits - to 2-4 to 8 Min. d Max. d Min. d Max. d Analog Switch Analog Signal Range e V ANALOG - - V On-Resistance R ON = V, = - V I NO, I N = ma, V OM = ± 3. V Switch Off Leakage urrent a I NO(off) I N(off) I OM(off) =., = -. V V OM = ± 4. V V NO, V N = ± 4. V hannel On =. V, = -. V Leakage urrent a I OM(on) V NO, V N = V OM = ± 4. V igital ontrol Input urrent a I L or I H µa ynamic haracteristics Turn-On Time e t ON R L = 3, L = 3 pf Turn-Off Time e t OFF V NO, V N = ± 3. V, see figure ns Break-Before-Make Time G49L only, V elay e t NO, V N = 3. V R L = 3, L = 3 pf R TransitionTime t L = 3, L = 3 pf TRANS V S = ± 3. V, V S2 = ± 3. V harge Injection e Q J V g = V, R g =, L = nf 3 p Off-Isolation e OIRR - 7 hannel-to-hannel R L =, L = pf, f = MHz db rosstalk e X TALK Unit na Source Off apacitance e NO(off) N(off) f = MHz.2 hannel-on apacitance e ON Power Supplies Positive Supply urrent e I+ Negative Supply urrent e I- V = or Logic Supply urrent e I L Ground urrent e I GN pf µa ocument Number: 7763 S3-86-Rev. G, 9-Aug-3 3 THE PROUT ESRIBE HERE AN THIS OUMENT ARE SUBJET TO SPEIFI ISLAIMERS, SET FORTH AT /doc?9

4 G47L, G48L, G49L SPEIFIATIONS (Single Supply V) Parameter Symbol Test onditions Unless Otherwise Specified = V, = V = V, V = 2.4 V,.8 V f Temp. b Typ. c A Suffix Limits - to 2 Suffix Limits - 4 to 8 Min. d Max. d Min. d Max. d Analog Switch Analog Signal Range e V ANALOG V On-Resistance e R ON = 4. V, I NO, I N = ma V OM = V, 3. V ynamic haracteristics Turn-On Time e t ON R L = 3, L = 3 pf Turn-Off Time e t OFF V NO, V N = 3. V, see figure ns Break-Before-Make Time G49L only, V elay e t NO, V N = 3. V R L = 3, L = 3 pf 9 harge Injection e Q J V g = V, R g =, L = nf.4 p Power Supplies Positive Supply urrent e I+ Negative Supply urrent e I- V = or Logic Supply urrent e I L Ground urrent e I GN Unit µa 4 ocument Number: 7763 S3-86-Rev. G, 9-Aug-3 THE PROUT ESRIBE HERE AN THIS OUMENT ARE SUBJET TO SPEIFI ISLAIMERS, SET FORTH AT /doc?9

5 G47L, G48L, G49L SPEIFIATIONS (Single Supply 3 V) Parameter Symbol Test onditions Unless Otherwise Specified = 3 V, = V = 3 V, V = 2 V,.4 V f Temp. b Typ. c A Suffix Limits - to 2 Suffix Limits - 4 to 8 Min. d Max. d Min. d Max. d Analog Switch Analog Signal Range e V ANALOG 3 3 V On-Resistance R ON = 2.7 V, = V I NO, I N = ma, V OM =. V, 2.2 V Switch Off Leakage urrent a I NO(off) I N(off) I OM(off) = 3.3, = V V OM =, 2 V, V NO, V N = 2, V hannel On = 3.3 V, = V Leakage urrent a I OM(on) V NO, V N = V OM = V, 2 V igital ontrol Input urrent a I L or I H µa ynamic haracteristics Turn-On Time t ON R L = 3, L = 3 pf Turn-Off Time t OFF V NO, V N =. V, see figure ns Break-Before-Make Time elay t G49L only, V NO, V N =. V R L = 3, L = 3 pf Notes: a. Leakage parameters are guaranteed by worst case test condition and not subject to production test. b. = 2, = as determined by the operating temperature suffix. c. Typical values are for ESIGN AI ONLY, not guaranteed nor subject to production testing. d. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet. e. Guaranteed by design, not subject to production test. f. V = input voltage to perform proper function harge Injection e Q J V g = V, R g =, L = nf p Off-Isolation e OIRR - 7 hannel-to-hannel R L =, L = pf, f = MHz db rosstalk e X TALK - 77 Source Off apacitance e NO(off) N(off) f = MHz.6 hannel On apacitance e (on) Unit na pf Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ocument Number: 7763 S3-86-Rev. G, 9-Aug-3 THE PROUT ESRIBE HERE AN THIS OUMENT ARE SUBJET TO SPEIFI ISLAIMERS, SET FORTH AT /doc?9

6 G47L, G48L, G49L TYPIAL HARATERISTIS (2, unless otherwise noted) - On-Resistance (Ω) R ON = 2.7 V T = 2 I S = ma = 4. V =.8 V - On-Resistance (Ω) R ON I S = ma E = 2.7 V A B A = 2 B = 8 = 2 = - 4 E = - = 4. V A B E V OM - Analog V oltage (V) R ON vs. V OM and Supply Voltage V OM - Analog V oltage (V) R ON vs. Analog Voltage and Temperature 3 2 V ± = ± V I S = ma V ± = ± V V = V R ON - On-Resistance (Ω) Supply urrent (na) I V O M - Analog Voltage (V) R ON vs. Analog Voltage and Temperature Temperature ( ) Supply urrent vs. Temperature m m = 2 V V - = V I+ - Supply urrent (na) µ µ µ n Leakage urrent (pa) I O M( on) I O M ( of f) n K K K M M Input Switching Frequency (Hz) Supply urrent vs. Input Switching Frequency Temperature ( ) Leakage urrent vs. Temperature 6 ocument Number: 7763 S3-86-Rev. G, 9-Aug-3 THE PROUT ESRIBE HERE AN THIS OUMENT ARE SUBJET TO SPEIFI ISLAIMERS, SET FORTH AT /doc?9

7 G47L, G48L, G49L TYPIAL HARATERISTIS (2, unless otherwise noted) 4 9 Leakage urrent (pa) 2-2 = 2 V V - = V I O M ( of f) /I O M( on) I NO ( o f f ) /I N( on) - Switching Time (ns) ton, toff t ON = 3 V t ON = V t ON = 2 V t OFF = V t OFF = 3 V t OFF = 2 V V OM, V NO, V N - Analog Voltage (V) Temperature ( ) Leakage vs. Analog Voltage Switching Time vs. Temperature and Single Supply Voltage Loss - Switching Time (ns) t ON, toff t ON = ± 3 V t ON = ± V t ON = ± 6 V t OFF = ± 3 V t OFF = ± 6 V t OFF = ± V Loss, OIRR, X TALK (db) OIRR X TALK = 3 V = V R L = - K M M M G Temperature ( ) Frequency (Hz) Switching Time vs. Temperature and ual Supply Voltage Insertion Loss, Off -Isolation rosstalk vs. Frequency - Switching Threshold (V) VT 2..8 = Supply V oltage (V) Switching Threshold vs. Supply Voltage Q - harge Injection (p) 2 = 2 V 8 6 = V 4 V = ± V 2 = 3 V V OM - Analog V oltage (V) harge Injection vs. Analog Voltage) ocument Number: 7763 S3-86-Rev. G, 9-Aug-3 7 THE PROUT ESRIBE HERE AN THIS OUMENT ARE SUBJET TO SPEIFI ISLAIMERS, SET FORTH AT /doc?9

8 G47L, G48L, G49L SHEMATI IAGRAM (Typical hannel) S V Level Shift/ rive GN Figure. TEST IRUITS Logic Input V H % t r < ns t f < ns Switch Input V NO or N GN OM R L 3 Ω Switch Output L 3 pf V OU T Switch Output V L V V OU T t ON 9 % t OFF.9 x V OU T L (includes fixture and stray capacitance) V OU T = V R L R L + R ON Note: Logic input waveform is inverted for switches that have the opposite logic sense control Figure 2. Switching Time Logic Input V H t r < ns t f < ns V NO NO OM V O V L V N N R L 3 Ω L 3 pf V N = V NO V O 9 % GN Switch Output V t t L (includes fixture and stray capacitance) Figure 3. Break-Before-Make (G49L) 8 ocument Number: 7763 S3-86-Rev. G, 9-Aug-3 THE PROUT ESRIBE HERE AN THIS OUMENT ARE SUBJET TO SPEIFI ISLAIMERS, SET FORTH AT /doc?9

9 G47L, G48L, G49L TEST IRUITS + V + V V S V S2 NO or N N or NO OM R L 3 Ω L 3 pf V O Logic Input V H V L V S V % t TR A N S t r < ns t f < ns t TR A N S 9 % GN Switch Output V S2 V 2 % L (includes fixture and stray capacitance) V O = V S R L R L + R ON Figure 4. Transition Time (G49L) ΔV O R g OM NO or N V O V O OFF ON OFF V g GN L nf Q = ΔV O x L dependent on switch configuration Input polarity determined by sense of switch. V = - Figure. harge Injection V + V S V V + NO or N OM R g = V or 2.4 V V OU T N or NO GN V - X TA L K Isolation = 2 log = RF bypass V OU T V Figure 6. rosstalk (G49L) ocument Number: 7763 S3-86-Rev. G, 9-Aug-3 9 THE PROUT ESRIBE HERE AN THIS OUMENT ARE SUBJET TO SPEIFI ISLAIMERS, SET FORTH AT /doc?9

10 G47L, G48L, G49L TEST IRUITS NO or N OM R g = Ω V, 2.4 V R L Ω GN Off Isolation = 2 log = RF Bypass V OM V NO/N Figure 7. Off Isolation OM Meter V, 2.4 V NO or N HP492A Impedance Analyzer or Equivalent GN f = MHz Figure 8. Source/rain apacitances maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and reliability data, see /ppg?7763. ocument Number: 7763 S3-86-Rev. G, 9-Aug-3 THE PROUT ESRIBE HERE AN THIS OUMENT ARE SUBJET TO SPEIFI ISLAIMERS, SET FORTH AT /doc?9

11 Package Information SOI (NARROW): 8-LEA JEE Part Number: MS E H S A.2 mm (Gage Plane) h x 4 All Leads e B A L q. mm.4" MILLIMETERS HES IM Min Max Min Max A A B E e.27 BS. BS H h L q 8 8 S EN: -627-Rev. I, -Sep-6 WG: 498 ocument Number: 792 -Sep-6

12 Package Information MSOP: 8 LEAS JEE Part Number: MO-87, (Variation AA and BA) (N/2) Tips) N N- A B 2X.2 E.6.48 Max etail B (Scale: 3/) ambar Protrusion..6 2 N/2 Top View b.8 M B S A S 7 b e See etail B e A With Plating c c.2 BS Parting Line L 4 etail A (Scale: 3/) NOTES:. ie thickness allowable is imensioning and tolerances per ANSI.Y4.M imensions and E do not include mold flash or protrusions, and are measured at atum plane -H-, mold flash or protrusions shall not exceed. mm per side. 4. imension is the length of terminal for soldering to a substrate.. Terminal positions are shown for reference only. 6. Formed leads shall be planar with respect to one another within. mm at seating plane. 7. The lead width dimension does not include ambar protrusion. Allowable ambar protrusion shall be.8 mm total in excess of the lead width dimension at maximum material condition. ambar cannot be located on the lower radius or the lead foot. Minimum space between protrusions and an adjacent lead to be.4 mm. See detail B and Section Section - to be determined at. mm to.2 mm from the lead tip. 9. ontrolling dimension: millimeters. 3 Side View.9. This part is compliant with JEE registration MO-87, variation AA and BA.. atums -A- and -B- to be determined atum plane -H-. 2. Exposed pad area in bottom side is the same as teh leadframe pad size. A.7 R. Min 2 Places Seating Plane. Seating Plane 6 Base Metal See etail A A 2. S Section - Scale: / (See Note 8) ς E 3 End View N = 8L MILLIMETERS im Min Nom Max Note A - -. A... A b b c c BS 3 E 4.9 BS E e.6 BS e.9 BS L N EN: T-28 Rev., -Jul-2 WG: 867 -H- -A- -- -B- ocument Number: Jul-2

13 Application Note 826 REOMMENE MIMUM PAS FOR SO-8.72 (4.369).28 (.7) APPLIATION NOTE.47 (.94).246 (6.248).2 (3.86).22 (.9). (.27) Recommended Minimum Pads imensions in Inches/(mm) Return to Index Return to Index ocument Number: Revision: 2-Jan-8

14 Legal isclaimer Notice Vishay isclaimer ALL PROUT, PROUT SPEIFIATIONS AN ATA ARE SUBJET TO HANGE WITHOUT NOTIE TO IMPROVE RELIABILITY, FUNTION OR ESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer s technical experts. Product specifications do not expand or otherwise modify Vishay s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. ustomers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. 27 VISHAY TERTEHNOLOGY,. ALL RIGHTS RESERVE Revision: 8-Feb-7 ocument Number: 9