HALFEN FRAMING CHANNELS AND ACCESSORIES FRAMING

Transcription

1 HAEN RAMING CHANNES AND ACCESSORIES RAMING

2 HAEN RAMING SYSTEMS Product range - Overview pages - pages - pages - Heav dut framing sstems data Z Q Medium dut framing sstems pages - 0 pages - 0 pages - 0 Ma. tensile / transv. tens. Ma. load force Compr. member pages - page 8 page 9 data pages - Ma. tensile / transv. tens. force Z Q Ma. load Compr. member ight dut framing sstems data Ma. tensile / transv. tens. force Q Z Ma. load Compr. member page 8 page 9 pages - page 8 page 9 pages 8-8 page - pages - 9 pages 0 - page 8 Halfen cast-in channels and accessories page 8 page 8 page 8 pages 8-8 iing parts nut he head bolt and Washer HCS - AS lateral reinforcement HCS - RS frame stand pages - HCS - R pipe clamp fiing he head bolt nut and iing parts KON cantilever arm HCS - R pipe clamp fiing he head bolt nut and iing parts KON cantilever arm he head bolt nut and iing parts HCS - RAD - - für Da 8, HCS - RAD - - für Da 9, HAEN-DEHA Vertriebsgesellschaft mbh iebigstr. 0 angenfeld Tel. 0/90-0 a. Tel. 0/90- To draw no.: Construction account: Requested deliver date: No. pieces Stock no. Tpe/ channel Date of order: Compan: Deliver adress: inish ength Name: Comments Tel.: a: Price [ / piece] pages 9-9 VA composite anchor (pin) pages 9-00 page 0

3 HAEN RAMING SYSTEMS Inde HAEN raming channels, HAEN T-head bolts Heav dut framing sstems Medium dut framing sstems ight dut framing sstems page: HAEN raming sstem accessories page: Threaded rods, he-head bolts, nuts, accessories Clamps, beam clamps Ductwork supports and accessories Design properties, materials, corrosion protection Materials, design tpes / finishes of HAEN s and T-head bolts Section properties of HAEN raming channels (plain back and slotted); other data oading capacit of HAEN s as compression members oading capacit data for HAEN T-head bolts page: HAEN Support structures, ittings, Sstem POWERCICK HAEN POWERCICK raming Sstem ; Sstem (heav dut) Sstem and (medium dut), Standard sstems Sstem (light dut) Sstem 8 (light dut) HAEN Cantilevers Cantilevers KON Pipe clamps, pipe support Pipe clamps, pipe clamp - fiing sets, HAEN Combisstem HCS Pipe supports Pipe weights, support spacings, dimensionings of pipe clamps (tables) Tpical bridge drainage fiing details Notes, work aid iing to cast-in HAEN s Specification wording eamples Order form page: page: - page: page: Inde A - Z 0

4 HAEN RAMING SYSTEMS iing (Introduction) Adjustable HAEN channel fiing sstems offer a whole range of benefits: Non-slip bolting at an point with Halfen T-head bolts. Corrosion protection remains intact after bolting. Can be adjusted or etended on site without an need for machining (it is therefore not restricted b different hole settings when changes are made to components). Several different thread diameters can be used in one channel. High corrosion protection of structural components through hot-dip galvanising (piece galvanisation). Alternativel, pre-galvanised versions are available for lower corrosion protection requirements. A large selection of standard channels with ecellent load bearing characteristics. HAEN raming channels represent support structures and fiing materials all in one. - HAEN Qualit Management Sstem certified acc. to DIN EN 900, Certificate no. QS 8 HH for the locations in German, Switerland and Ponan / Poland. Using HAEN raming channels uneconomic procedures are avoided such as: - costl machining and corrosion protection on finished structural units during retrofitting or on-site adaptation. - time-consuming hole setting calculations for structural parts requiring large numbers of bolts. - costl manufacture of purpose-made bolted structures. e.g. M e = 0 mm

5 HAEN RAMING SYSTEMS Steel (Introduction) Adjustable HAEN support structures offer a whole range of benefits: Efficient and economical production of modular sstem support structures, made-tomeasure and supplied with all the necessar bolts and fittings. Precision on-site adaptation made simple (reducing time needed for planning and observing production tolerances). ow-cost full adjustable standard products which can replace a whole range of epensive structural parts. Special designs are possible for all structural parts depending on the quantities involved. height adjustable laterall adjustable An component can be replaced at an time without an fuss Using HAEN Support structures uneconomic procedures are avoided such as: - comple design work on constructions where conditions are subject to change or in cases where structural components need to be mounted so as to be easil replaceable. - elaborate adaptation work where wide construction tolerances or on-site retrofitting is required. - uneconomical purpose-made structural components. Requ. position Actual position

6 HAEN RAMING CHANNES AND ACCESSORIES Heav Dut raming s Halfen hot rolled channels Z up to kn Product features The hot rolling process makes these Halfen channels ideall suitable for: dnamic loads welding heav loads Due to their abilit to withstand dnamic loads the hot rolled HAEN s are also well suited to fleible mounting of components in machines, vehicles etc. up to, kn HM /8 pages 8 - HM / Q up to 9 kn HM 0/0 suitable for welding Select the most economic channel depending on the loading. HM 0/ HZM 8/ HZM 9/0 High load distribution, shear force Q up to 9 kn, tensile force Z up to kn and force in longitudinal direction up to, kn. Material/construction: Mild steel, hot-dip galvanised (), Zinc coating 0 µm or mill finish (wb). Stainless steel version: W./.0 (A) All hot rolled HAEN s are available both as framing channels and also as HTA cast-in channels ( p. 9). Both versions use the same bolts and thread plates. HM HM = surface mounted, HTA = cast in HTA Concrete

7 HAEN RAMING CHANNES AND ACCESSORIES Heav Dut raming s for hot rolled Halfen channels Product features or ever hot rolled HAEN there are matching Halfen T-head bolts and locking plates (from M up to M 0, depending on channel). High degree of safet: HSR - HAEN T-head bolts are nibbed and and therefore non-slip. Up to, kn (with safet factor n = )perbolt when used in mild steel channels (material qualit = hot-dip galvanised and wb = mill finish). Corrosion protection provided b galvanising remains full intact even after assembl. Selection of HAEN T-head bolts and locking plates Tpe HSR with nib pages 9-9 Tpe HS Tpe GWP pages 9-9 There is a large selection of Stainless steel HS HAEN T-head bolts and GWP locking plates (from M 8 up to M 0,depending on section) for all Stainless steel channels. Twist protection due to the hook-head shape of the profile lips in conjunction with the hook-head bolts and locking plates. Unintential twisting of the bolts resp. locking plates, e.g. due to vibrations, is impossible. HAEN locking plates allow the use of an kind of bolts.

8 HAEN RAMING CHANNES /8 HM /8 hot rolled,, 8, bolt length l Nominal dimensions HM /8 Back-to-back channels to order HM /8 D Material, finish for eplan. see p. ength: 00 mm Stock no HM /8 wb A Bolt-accessories Standard = To order = Cross weight section G [kg/m] Z Q VUS /9 Washers for direct assembl A [cm²] Moment of inertia I [cm ] Order eample: HM / Other channel data, design properties Ma. tensile / Ma. load transverse compression data load member pages - page 8 page 9 VUS /9 I [cm ] Section modulus W [cm³] W [cm³] Ma. perm. point loading ma ma Bending capacit at span or Stock no see note on p. [m] 0,0,00 [cm],0 8,8,,99 8,0,,08,0,0,0,, Subject to alterations page 8

9 HAEN T-HEAD BOTS AND ACCESSORIES for /8 HS /8 Halfen T-head bolt incl. nut 8 ength l M 0 M ength l Mat. ength l Mat Order eample: HS /8 - M 00 - M M 0 M ength l Mat. ength l Mat. ength l Mat A-0 A-0 l HSR /8 Halfen T-head bolt with nibs incl. nut l Halfen T-head bolts - load capacities Thread Ø M 0 M M M 0 8 Ma. pull out per T-head bolt Grade.,0 8,8 0,, S Material/finish Halfen T-head bolts ( S. ): = h.d. galvanised, strength grade. = electroplated, strength grade. 8.8 = h.d. galvanised, strength grade 8.8 A-0 = Stainless steel grade A-0 ength l M 0 GWP /8 ocking plates ength l Mat. Thread M Order eample: HSR /8 - M M M 0 Order eample: GWP /8 - M 0 Grade 8.8, 8, 0,0 9,0 for mild steel channels Note: Do not eceed channel load capacit! See also p. - 9 (design properties). d Ma. longitudinal load per Halfen T-head bolt Tpe HS, grade. Tpe HS, grade 8.8 Tpe HSR, grade 8.8 tightening tightening tightening torque torque ( = ) torque [Nm] [Nm] [Nm], 0, 00, 00,0 00,8 80, 00 8,9 000, 00 0,9 00 b a i l requ. t mv perm. load Halfen t-head bolt S Thread M M M 0 Ma. pull out per T-head bolt S Grade A - 0 = Standard = To order - Calculation of bolt length l requ. for Halfen T-head bolts: lrequ. = required bolt length i m v = profile lip = nut = spare ~mm t = clamping thickness ( t l - l A Thread M M M 0 loading capacit 9,,,0 for stainless steel channels required deduction) Ma. longitudinal load per Halfen T-head bolt Grade A - 0 a b l deduct. d tightening torque [Nm] 8,8,0 00 9

10 HAEN RAMING CHANNES / HM / hot rolled,,, Material, finish for eplan. see p. Stock no HM / wb A ength: 00 mm Standard weight = To order = G [kg/m] Cross section A [cm²] Moment of inertia Order eample: HM / Section modulus Ma. perm. point loading or Stock no. ma Bending capacit at span [m] ma I I W W 0,0,00 [cm ] [cm ] [cm³] [cm³] [cm],0,9, 9,,,9 9,9,0,0 8,,, see note on p. Nominal dimensions Other channel data, design properties HM / Back-to-back channels to order HM / D Base channel for Sstem Series HAEN Sstem Series page HAEN Series Cantilevers page HAEN Series ittings page data Z Q pages - page 8 page 9 -accessories SDM /8 Sound attenuator page 0 Ma. tensile / transverse load Bolt-accessories VUS / Washer for direct assembl Ma. load compression member HPE / end cap VUS / page PA - closer strip page Subject to alterations page 0

11 l HAEN T-HEAD BOTS AND ACCESSORIES for / HS 0/0 Halfen T-head bolt incl. nut Halfen T-head bolt with nibs incl. nut l HSR 0/0 Halfen T-head bolts - load capacities ength l 0 Order eample: HS 0/0 -M 0- ength l 0 0 Ma. pull out per T-head bolt S M0 ength l Mat M ength l Mat M M M0 M M M0 ength l Mat. ength l Mat. ength l Mat. ength l Mat. ength l Mat. ength l Mat A-0 0 A-0 M0 ength l Mat. Material / finish Halfen T-head bolts ( p. ): = h.d. galvanised, strength grade. = electroplated, strength grade. 8.8 = h.d. galvanised, strength grade = electroplated, strength grade 8.8 A-0 = Stainless steel grade A-0 Tpe HS, grade. GWP 0/0 ocking plates d for mild steel channels Ma. longitudinal load per Halfen T-head bolt b Tpe HSR, grade 8.8 Grade Grade tightening tightening. 8.8 torque ( = ) torque Thread Ø [Nm] [Nm] M 0,, 0, M 9, 9, 0, M,, 0,9 0,0 00 M 0,0,, 0, 00 Note: Do not eceed channel load capacit! See also p. - 9 (design properties) a Thread M 8 M 0 M M Order eample: GWP 0/0 -M- perm. load Thread loading capacit M 8,0 M 0, M 9, S M 9, Ma. pull out per T-head bolt S Grade A - 0, 9,,,0 A-0 A-0 A-0 = Standard = To order A Thread M 8 M 0 M M A-0 A-0 A-0 A-0 A-0 for stainless steel channels Grade A - 0 0, 0, 0,9, Calculation of bolt length lrequ. p. 9 a,,,, 00 b Ma. longitudinal load per Halfen T-head bolt A-0 A-0 A-0 A-0 A-0 0 A-0 d tightening torque [Nm] 0 0

12 HAEN RAMING CHANNES s 0/0 and 9/0 HM 0/0 hot rolled, 8 Nominal dimensions 9 0 Material, finish for eplan. see p. Stock no HM 0/0 wb A HM 9/0 wb A A Standard = To order = Cross weight section G [kg/m] A [cm²] Moment of inertia ength: 00 mm Order eample: HM 0/ Material: Stainless steel W., Material order code HCR, on request. Other channel data, design properties Section modulus Ma. perm. point loading ma or Stock no. Bending capacit at span [m] ma I I W W 0,0,00 [cm ] [cm ] [cm³] [cm³] [cm],0,,,,,,8,0 9,0,,,,0,9,,9,,,9,,, see note on p. HM 9/0 cold rolled, HM 0/0 Back-to-back channels to order, Nominal dimensions 0 HM 0/0 D 0 data Ma. tensile / transverse load Q Z pages - page 8 page 9 -accessories SDM /8 Sound attenuator page 0 Ma. load compression member Bolt-accessories VUS / SIC 0/0 Washer for direct assembl ock washers PA - closer strip page VUS / SIC 0/0 Subject to alterations page page

13 l HAEN T-HEAD BOTS AND ACCESSORIES for s 0/0 (hot rolled) and 9/0 (cold rolled) HS 0/0 Halfen T-head bolt incl. nut l HSR 0/0 Halfen T-head bolt with nibs incl. nut Halfen T-head bolts - load capacities ength l Order eample: HS 0/0 -M 0- High corrosion resistant Stainless steel T-head bolts HS 0/0, material order code HCR, on request. ength l 0 0 Ma. pull out per T-head bolt M0 ength l Mat M ength l Mat Material / finish Halfen T-head bolts ( p. ) : = h.d. galvanised, strength grade. = electroplated, strength grade. 8.8 = h.d. galvanised, strength grade = electroplated, strength grade 8.8 A-0 = Stainless steel grade A-0 M M M0 M M M0 ength l Mat. ength l Mat. ength l Mat. ength l Mat. ength l Mat. ength l Mat A-0 0 A M0 ength l Mat GWP 0/0 ocking plates d for mild steel channels Ma. longitudinal load per Halfen T-head bolt b a Thread M 8 M 0 M M Order eample: GWP 0/0 -M- perm. load Thread M 8 M 0 M S M Ma. pull out per T-head bolt A Thread M 8 M 0 M M loading capacit,0, 9, 9, for stainless steel channels Calculation of bolt length lrequ. p. 9 Ma. longitudinal load per Halfen T-head bolt S Tpe HS, grade. Tpe HSR, grade 8.8 S Grade Grade tightening tightening Grade Grade tightening. 8.8 torque ( = ) torque A - 0 A - 0 torque Thread Ø [Nm] [Nm] [Nm] M 0,, 0,, 0, M 9, 9, 0, 9, 0, M,, 0,9 0,0 00, 0,9 0 M 0,0,, 0, 00,0, 0 Note: Do not eceed channel load capacit! See also p. - 9 (design properties). = Standard = To order A-0 A-0 A A-0 A-0 A-0 A-0 A-0 00 a b,,,, A-0 A-0 A-0 A-0 A-0 0 A-0 d

14 HAEN RAMING CHANNES s 0/, 0/ and HM 0/ hot rolled 9,, 8 Material, finish for eplan. see p. HM 0/ Stock no Standard = To order = Cross weight section G [kg/m] A [cm²] Moment of inertia I [cm ] I [cm ] Section modulus W [cm³] W [cm³] Ma. perm. point loading ma ma [cm] Bending capacit at span 0,0 [m],00,0, Nominal dimensions HM 0/ cold rolled HM 0/ Back-to-back channels to order HM 0/ HM 0 HM (C 0) cold rolled 8 9, 8 Nominal dimensions HM 0/ D, Subject to alterations wb ,,0,0,8,,9,,0,, 0, A HM 0/ wb ,08,,0,0,,0,8,0,,0 0, A A ength: 00 mm Order eample: HM 0/ or Stock no see note on p. Other channel data, design properties -accessories Ma. tensile / Ma. load Sound attenuator transverse compression data SDM / load member Q Z pages - page 8 page 9 Bolt-accessories VUS 0/ Washer for direct assembl HM wb ength: 000 mm page page 0 SIC 0/ ock washers page The cold rolled profile HM is intended to be used for pre-dominantl static loads. or dnamic load the profile HM 0/ is to be used. Material, finish for eplan. see p. Stock no Standard = To order = Cross weight section G [kg/m], A [cm²],98 VUS 0/ SIC 0/ Moment of inertia I [cm ], I [cm ],9 Section modulus W [cm³] Order eample: HM W [cm³] Ma. perm. point loading or Stock no. 0,0 [cm] Bending capacit at span [m], see note on p. urther design properties: pages - 9; accessories: same as HM 0/ (see above),0, ma, ma,0,8 0,8,0 0,

15 l HAEN T-HEAD BOTS AND ACCESSORIES for s 0/ and HS 0/ ength l M 0 M M M 0 M M Halfen T-head bolt ength l Mat. ength l Mat. ength l Mat. ength l Mat. ength l Mat. incl. nut A-0 0 A-0 0 A A-0 0 A-0 0 A A-0 0 A-0 0 A i 0i A A A-0 80 A-0 80 i 80i A-0 80i A A-0 00 A A-0 0 A-0 i = eft hand thread A Order code: HS 0/ - M 0 - Calculation of bolt length lrequ. p. 9, HSR 0/ Halfen T-head bolt with nibs incl. nut l Halfen T-head bolts - load capacities Thread Ø M 0 M M, Ma. pull out per T-head bolt ength l M GWP 0/ A ength l Mat. ocking plates Thread Thread M M 8 M 8 Order code: M 0 M 0 HSR 0/ - M M M Material/finish Halfen T-head bolts ( p. ): = h.d. galvanised, strength grade. = electroplated, strength grade. 8.8 = h.d. galvanised, strength grade 8.8 A-0 = Stainless steel grade A-0 S Tp HS, grade. Tp HS, grade 8.8 Tp HSR, grade 8.8 grade grade tightening tightening tightening. 8.8 torque torque ( = ) torque [Nm] [Nm] [Nm],, 0,, 8 9, 9, 0,, 0,, 0,9 0,0 00,0 00 d for mild steel channels Ma. longitudinal load per Halfen T-head bolt b a Order code: GWP 0/ - M 0 - perm. load S Thread M M 8 M 0 M Ma. pull out per T-head bolt S a loading capacit,,0, 9, for stainless steel channels b Ma. longitudinal load per Halfen T-head bolt d 0 0 0, grade A - 0 grade A - 0 tightening torque [Nm], 0, 9, 0,, 0,9 0 Note: Do not eceed channel load capacit! See also p. - 9 (design properties). = Standard = To order

16 HAEN RAMING CHANNES s HZM 8/ and 9/0 HZM 8/ toothed, hot rolled NEW! 8 Material, finish for eplan. see p. Stock no HZM 8/ Standard = To order = Cross weight section G [kg/m] A [cm²] Moment of inertia I [cm ] I [cm ] Section modulus W [cm³] W [cm³] Ma. perm. point loading ma ma [cm] Bending capacit at span [m] 0,0,00,0 8 wb ength: 00 mm,,09,,,9,,0 0, Order eample: HZM 8/ or Stock no., 0, see note on p. Nominal dimensions HZM 8/ Other channel data, design properties Ma. tensile / Ma. longitud. transverse data tensile load load Z pages - page 8 Q page 8 Toothing mm -accessories SDM / Sound attenuator page 0 HZM 9/0 toothed, hot rolled NEW! 0 Nominal dimensions HZM 9/0 9 Material, finish for eplan. see p ength: 00 mm Stock no HZM 8/ wb Standard = To order = Z pages - page 8 Cross weight section G [kg/m] Q A [cm²] Moment of inertia I [cm ] page 8 I [cm ] Section modulus Order eample: HZM 9/ Other channel data, design properties Ma. tensile / Ma. longitud. transverse data tensile load load W [cm³] mm Toothing W [cm³] Ma. perm. point loading ma or Stock no. ma Bending capacit at span [m] 0,0,00 [cm],,98,0, 0,9, 8,0,,0 0, 0, see note on p. Subject to alterations

17 l l l l HAEN T-HEAD BOTS AND ACCESSORIES for s HZM 8/ and 9/0 Toothed bolts incl. nut Hammer-head bolts incl. nut load in all directions oad vertical to longitudinal direction for 8/ for Ch. 9/0 for 8/ for 9/0 9 0,, position marking at shank end of Halfen bolts: notches = Tpe HZS, toothed notch = Tp HS, smooth ength l Q Q Q Q Q Q Q Q Q Q Q Q GWP 8/ d Q Q Bolt-accessories for s HZM 8/ VUS 0/ Washer for direct assembl page b SIC 8/ ock washers a page GWP 8/ Perm. load capacities for Halfen T-head bolts, requ. tightening torque, perm. bending moment fits to 8/ fits to 9/0 Refered to leading edge of channel resp. concrete. In case of bending with additional tensile load, calculate with superposition: Halfen T-head bolts:, grade 8.8 tightening torque Thread M M 8 M 0 M M M M M M 0 M M M M 8 M Material Material Material Material Material Material Material Material Material Material load ranges Note: 8.8 resp.. = galvanic special coating for particularl long-lasting corrosion protection, allowed to make up for hot-dip galvanised (cp. approval. DIBt Z-.-9 Halfen s, Att. Tab. ); grade 8.8 resp... ocking plates GWP HZS 8/ HZS 9/0 HS 8/ HS 8/ HS 8/ HS 9/0 M for 8/ page o HZS HS, grade. Perm. Perm. bending tightening Perm. tensile/ in all directions moment per bolt torque transverse load VUS 0/ SIC 8/ Perm. bending moment per bolt.... requ. hole adjacent element [Nm] [Nm] [Nm], [Nm],0 8,0,0 9, 0,0 80 9,, 9,, 0, 0,, for 9/0 page 9 o. perm. ( - M/perm.M) d T-head bolts HS (= smooth) are not suitable to loading direction (loads in longitudinal direction). Do not eceed channel load capacit ( pages - 9). b a perm. perm. M M Bolt-accessories for s HZM 9/0 US Washer for direct assembl page approved for dnamic loads Calculation of bolt length lrequ. p. 9 = perm. tensile force = perm. bending moment = eisting tensile force = eisting bending moment SIC 9/0 ock washers US DIN SIC 9/0 page

18 HAEN RAMING CHANNES s 0/0 and 8 HM bw. H 0/0 cold rolled HM 8 cold rolled, Nominal dimensions HM 0/0 HM 8 0 H 0/0 slotted Nominal dimensions Subject to alterations Cold rolled profiles are intended to be used for pre-dominantl static loads. or dnamic load hot-rolled profiles (pages 8 - ) are to be used. Material, finish for eplan. see p. ength: 000 mm Stock no. pages - Standard = To order = HM 0/ wb A H 0/ wb A Z Cross weight section page 8 Q pages - Moment of inertia page 9 Section modulus Order eample: HM 0/0 - A Other channel data, design properties Material, finish data Ma. tensile / transverse load Standard = G [kg/m],, Cross weight section Ma. load compression member Moment of inertia page 0 page 0 Ma. perm. point loading ma or Stock no. page Bending capacit at span [m] see note on p. -accessories SDM /8 PA HPE 0/0 Sound attenuator closer end cap strip Section modulus Ma. perm. point loading page page Bending capacit at span for Stock To eplan. no. order [m] see p. = ma G A I I W W 0,0,00 [kg/m] [cm²] [cm ] [cm ] [cm³] [cm³] [cm],0 HM wb ,,9,9 9,,9,0,,0,, 0, ength: 000 mm Order eample: HM or Stock no see note on p. Other channel data, design properties -accessories data A [cm²],, I [cm ] 8,, I [cm ],0, W [cm³],9, W [cm³],, ma,, SDM /8 Sound attenuator 0,0 [cm],0,0 ma,9,8,00,,9 PA closer strip,0,0, 8

19 l HAEN T-HEAD BOTS AND ACCESSORIES for s 0/0 and 8 HS 0/0 Halfen T-head bolt incl. nut 8 d 0 i = left hand thread GWP 0/0 ocking plates b Thread Ø M 0 M M M 0 GWP 0/0 ocking plates Halfen T-head bolts - load capacities a grade., 9,,,0 ength l Order code: Ma. pull out per T-head bolt S Order code: Material / finish Halfen T-head bolts ( p. ) = electroplated, str. gr.. = h.d. galvanised, str. gr.. A-0 = Stainless steel A-0 Thread M M 8 M 0 M M Thread M 8 M 0 M M grade 8.8, 9,,, M ength l Mat. ength l Mat. ength l Mat. ength l Mat. ength l Mat. ength l Mat A-0 0 A-0 A loading capacit Thread Thread M, M 8 M 8,0 M 0 M 0, M S M, M M, Thread abd Thread M 8, M 8,0 M 0, M 0, M, M 9, M, M 9, GWP 0/0 - M - for mild steel channels M Ma. longitudinal load per Halfen T-head bolt Tp HS, grade. tightening torque [Nm] 0, 0, 0,9 0, 0 M Note: Do not eceed channel load capacit! See also p. - 9 (design properties) HS 0/0 - M M Ma. pull out per T-head bolt Bolt-accessories VUS / SIC 0/0 Washer for direct assembl ock washers S M page for stainless steel channels grade A - 0 grade A - 0 tightening torque [Nm], 0, 9, 0,, 0,9 0,0, 0 = Standard = To order A-0 A-0 A-0 M Ma. longitudinal load per Halfen T-head bolt A-0 A-0 A-0 A-0 A-0 M 0 00 Calculation of bolt length lrequ. p. 9 page A-0 A-0 A-0 A-0 A-0 0 A-0 VUS / SIC 0/0 9

20 HAEN RAMING CHANNES / HZ / toothed, slotted Due to the toothed profile lips the channel is suitable for high loadings also in longitudinal direction. Base channel für Sstems Series Techn. Catalogue PC POWERCICK 8 0, toothing HZ / 9, 9, Nominal dimensions Product data Material, finish for eplan. see p. Stock no HZ / Standard weight = G [kg/m] Cross section A [cm²] Moment of inertia I [cm ] I [cm ] Section modulus W [cm³] W [cm³] Ma. perm. point loading ma ma Bending capacit at span [m] 0,0,00,0 [cm] Other channel data, design properties data Ma. load compression member - toothed, slotted see note on p. ength: 000 mm ength: 000 mm,,09,0,9 0,0,,, 8,, accessories SDM /8 PA Sound attenuator closer strip HPE / end cap pages - page 9 ocking plates, Halfen T-head bolts HZS / GWP / Order eample: HZ / or Stock no S HAEN Subject to alterations page 0 page page page 0

21 HAEN RAMING SYSTEM ACCESSORIES for / Basic channels kn POWERCICK bolt set pre-assembled in all fittings ocking plate with "bite" kn kn / / / HAEN POWERCICK ONE COMBINED SYSTEM for economical supports - Heav dut support sstem / - Medium dut support sstem / pages ight dut support sstem / All locking plates and bolts of Sstem fit to Sstem as well page GWP / kn GWP /SN HZS / Product range, technical details see Techn. catalogue PC HAEN POWERCICK

22 HAEN RAMING CHANNES AND ACCESSORIES Medium Dut raming Sstems HAEN raming s Sstem Series (Selection) / Product features With its numerous connecting parts and identical-format channels this sstem is especiall suitable for complete assemblies ( HAEN POWERCICK raming Sstem) low cost in-house stock-keeping One locking plate fits all Sstem HAEN s - both standard or toothed. / D ocking plate GWP / Base channel / /, /8 HZ / Heav Dut raming Sstems p. 0 ocking plate with 'bite'. The flamehardened teeth bite into the channel lips. High longitudinal loading capacit. Corrosion protection remains intact even after assembl. Suitable for all bolts with metric standard thread. When fitting smaller components (e.g. HAEN ittings) it is recommended that pre-assembled springless locking plates are used ( p. ). ocking plates with springs or HAEN Bolts are best suited for all fiing situations, especiall for larger structures.

23 HAEN RAMING CHANNES AND ACCESSORIES Medium Dut raming Sstems Base channel / Material / finish: wb sv = mill finish = hot-dip galvanised, inc coating > 0 µm, = pre-galvanised inc coating > 0 µm, A = A stainless steel To make fitting easier the locking plates and HAEN T-head bolts should be pre-mounted on the fittings to be attached. (Material data p. ) Associated framing sstems: - HAEN ittings p. - HAEN POWERCICK raming Sstem (Techn. catalogue HAEN POWERCICK raming Sstem, Notes p. ) - HAEN Cantilevers p. ocking plate Tpe GWP / p. Heagon head screw HSK - M p. Toothed channels provide shock-resistant fiing for non-slip connections and higher safet requirements.

24 HAEN RAMING CHANNES / HM resp. H /, HM / H / Nominal dimensions HM / D 0 8 Base channel for Sstem Series HAEN Sstem Series: page - 9 HAEN Series Cantilevers: page HAEN Series ittings: page Material, finish for eplan. see p. ength: 000 mm Note: Toothed profiles / page Stock no. Z Q pages - page 8 page 9 page Standard = To order = HM / wb sv A H / wb sv A HM/D wb A Cross weight section Moment of inertia S Section modulus Order eample: H / Other channel data, design properties data Ma. tensile / transverse load Ma. load compression member ocking plates, Halfen T-head bolts GWP / HZS / G [kg/m],,, A [cm²],,98 I [cm ],,0 I [cm ] 9, 9,,,8 8, W [cm³],0,8 8, page 0 W [cm³],, 8,9 SDM /8 Sound attenuator Ma. perm. point loading ma,,, or Stock no. ma -accessories PA closer strip page Bending capacit at span [m] 0,0,00 [cm] 8,0,0,0,,,9,,,,0,,, see note on p. HPE / end cap page

25 HAEN RAMING CHANNES / HM resp. H /, Material, finish for eplan. see p. Stock no. Standard = To order = Cross weight section G [kg/m] A [cm²] Moment of inertia I [cm ] I [cm ] Section modulus W [cm³] W [cm³] Ma. perm. point loading ma ma Bending capacit at span [m] 0,0,00 [cm],0 HM / H / Nominal dimensions HM / D Subject to alterations 0 8 HM / wb sv A H / wb sv A HM/D wb A ength: 000 mm Note: Toothed profile / page Z pages - page 8 page Order eample: Other channel data, design properties data,80,,0 Ma. tensile / transverse load Q,0,9,9,9 0,99, ocking plates, Halfen T-head bolts GWP / and / HZS / and / H / or Stock no see note on p. S,, 0, 0,9 0,89,9 -accessories SDM /8 Sound attenuator page 0,8,,,,,,0,0,0 PA closer strip page,8,, 0, 0,, 0, 0,, HPE / end cap page

26 HAEN RAMING CHANNES /, toothed HZM resp. HZ / toothed, Nominal dimensions HZM / HZ / HZM / D 0 8 Base channel for Sstem Series, toothed HAEN POWERCICK raming Sstem : page - 9 HAEN Series ittings: page Due to positive locking the profile is especiall suited when increased loading capacities in longitudinal direction are required, particularl in Stainless steel. Material, finish for eplan. see p. ength: 000 mm Stock no. Z Q pages - page 8 page 9 GWP / and / HZS / and / page Standard = To order = HZM / wb A HZ / wb A HZM/D wb A Cross weight section Order eample: Moment of inertia Other channel data, design properties data G [kg/m],, Ma. tensile / transverse load A [cm²],,90 ocking plates, Halfen T-head bolts I [cm ],9,8 S I [cm ] 9,0 9,0 Section modulus SDM /8 Sound attenuator Ma. perm. point loading PA closer strip page 0 page Bending capacit at span [m] HZM / - A or Stock no see note on p. Ma. load compression member W [cm³],9,9 W [cm³],,8 ma,, ma -accessories 0,0,00 [cm],0,0,,,,,0,,, 8,8 8, 8,90,,0,8,0,,, HPE / end cap page

27 HAEN RAMING CHANNES /, toothed HZM resp. HZ /, toothed, Due to positive locking the profile is especiall suited when increased loading capacities in longitudinal direction are required, particularl in Stainless steel. Material, finish for eplan. see p. Stock no. Standard = To order = Cross weight section G [kg/m] A [cm²] Moment of inertia I [cm ] I [cm ] Section modulus W [cm³] W [cm³] Ma. perm. point loading ma ma Bending capacit at span [m] 0,0,00 [cm],0 Nominal dimensions HZM / HZ / 0 8 HZM / wb A HZ / wb A HZM/D wb A ,9,,,8 ength: Order eample: HZM /: 00 mm HZ /: 000 mm HZM /D: 00 mm, 0,9,, 0,9 0,8,,9,8,,,00,8,,,0,,,,,,0,0 HZM / - A - 00 or Stock no see note on p.,, 0, 0, 0, 0, HZM / D Subject to alterations Other channel data, design properties data Z pages - page 8 page Ma. tensile / transverse load Q ocking plates, Halfen T-head bolts GWP / and / HZS / and / S -accessories SDM /8 Sound attenuator PA closer strip page 0 page HPE / end cap page

28 HAEN RAMING CHANNES / HM resp. H / Material, finish for eplan. see p. Stock no. Standard = To order = Cross weight section G [kg/m] A [cm²] Moment of inertia I [cm ] I [cm ] Section modulus W [cm³] W [cm³] Ma. perm. point loading ma ma Bending capacit at span [m],00,00 [cm],00, Nominal dimensions HM / wb sv H / wb sv HM / D wb ength: 000 mm Order eample: HM / or Stock no see note on p. Possible bulging, tilting and buckling must be prevented b appropriate measurements.,,,8,,99 0,8,0,,0,9,,, 8, 08,,,,9,,, 9,0 8,0 9,0,,,,,,,,0,0 HM / 0 H / HM / D 0 Other channel data, design properties data pages - Halfen T-head bolts HS / for mounting to the back of slotted channel ocking plates, Halfen T-head bolts GWP / HZS / page -accessories SDM /8 Sound attenuator S PA closer strip Subject to alterations page page 0 page 8

29 HAEN RAMING CHANNES /8 HM resp. H /8, 8 Material, finish for eplan. see p. Stock no. Standard = To order = HM / wb sv H / wb sv Cross weight section G [kg/m],,9 A [cm²],9,0 Moment of inertia I [cm ],0 I [cm ],00,0,9 Section modulus W [cm³] 9, 8,8 W [cm³] 8, 8,0 Ma. perm. point loading ma,, ma Bending capacit at span [m],00,00 [cm] 8,0,0 8,,,,,00,, ength: 000 mm Order eample: HM / or Stock no see note on p. Possible bulging, tilting and buckling must be prevented b appropriate measurements. Nominal dimensions HM /8 0 H /8 0 Other channel data, design properties data pages - Halfen T-head bolts HS / for mounting to the back of slotted channel ocking plates, Halfen T-head bolts GWP / HZS / page -accessories SDM /8 Sound attenuator PA closer strip S Subject to alterations page page 0 page 9

30 HAEN RAMING CHANNES s H / and / H /, Material, finish for eplan. see p. Stock no. Standard = To order = H / sv Cross weight section G [kg/m], A [cm²],9 Moment of inertia I [cm ], I [cm ],0 Section modulus W [cm³],0 W [cm³],9 Ma. perm. point loading ma,8 ma 0,0 [cm] 9,0 Bending capacit at span, [m],00,,0,0 H / Nominal dimensions 0 8 ength: 000 mm Order eample: H / - sv or Stock no see note on p. ocking plates, Halfen T-head bolts GWP / HZS / S -accessories SDM /8 Sound attenuator PA closer strip HPE / end cap page page 0 page page H /, H / Nominal dimensions 0 Subject to alterations 8 Material, finish for eplan. see p. Stock no. ength: 000 mm page Standard = To order = H / sv Cross weight section G [kg/m], A [cm²], Moment of inertia I [cm ] 0, S Section modulus -accessories SDM /8 Sound attenuator Ma. perm. point loading PA closer strip page 0 page Bending capacit at span [m] Order eample: H / - sv or Stock no see note on p. ocking plates, Halfen T-head bolts GWP / HZS / I [cm ], W [cm³] 0, W [cm³],8 ma,8 ma 0,0 [cm],0,,00 0, HPE / end cap page,0 0, 0

31 HAEN T-HEAD BOTS AND OCKING PATES for s / to /8 GWP / GWP /SN GWP /SH HZS / Dim. GWP / HZS / for all s with short spring with long spring for all s Series for toothed Chs. incl. nut, and Series for s for s (order nut GWP / and / for toothed b /, / / separatel) s / and b d HZS and / ( Note: / ( Note: Tpe HS / l d d d Tpe HS / without toothing l without toothing b b p. ) S. ) A d / b A 8.8 A Thread Thread Thread Thread Thr. l Thr. l Thread Thread Thr. l Thr. l M M M M /0 M M M M 8 M 8 M 8 M 8 M8 0 M 8 0 8/0 M 8 M 8 M 0 M 0 M0 M0 M0 M0 M0 0 M0 0 9/0 M0 M0 M 80 M* M M M 0 M 0 9/0 M M M M M 00 9/0 M 0 M 0 M M /0 M 00 M M M M 0 /0 M M Calculation of bolt length Perm. load capacities of ocking plates and Halfen T-head bolts Sstem Series lrequ. p. 9 Ma. pull out Ma. longitudinal load per Halfen T-head bolt resp. locking plate for mild steel channels per Halfen T-head bolt Tpes GWP / (not for thread M) and HZS / Material:, Note: Do not eceed HZS HZS channel / / load capacit! Thread M M 8 M0 M M M, ocking plates, for Stainless Steel s Material: Stainless Steel A Thread M M 8 M0 M M GWP / GWP / -SH, -SN GWP / GWP /, Halfen T-head bolts HZS / HZS / = plain form, fits to all s Series Does not fit to / Values in brackets for Tpes GWP / and HZS / S for all channels a. Series,0,0,0 9,0,0,0 Ma. pull out per Halfen T-head bolt, for s 0, HM/H /, /, /, /8,0,,,0,0,, for s HZM/HZ /,/, /,,0,0,0,0, Ma. longitudinal load per Halfen T-head bolt HZS / GWP GWP S / / Note: for s at tightening Do not eceed channel ocking plates Halfen T-head bolts torque load capacit! for s GWP GWP HZS HM/H HZM/HZ / / / [Nm],0 0,,,,0 0,,0,0,0,,,0,0,,0 (0),0,0,0,0 (80),0, at tightening torque [Nm] 8 0 at tightening torque [Nm],,0,,0 (0),0 (80) Insert dimension M (b = 0mm) from channel end = Standard d = mm at material A * = also deliverable in h.d. galvanised () Design perperties

32 HAEN RAMING CHANNES AND ACCESSORIES ight Dut raming Sstems Cold rolled HAEN raming s Z up to, kn up to,0 kn Q up to, kn Product features The light dut HAEN raming channels generall have a flat profile shape. The are particularl well suited for: combinations bolt / channel, where the materials and fittings are supplied b ourself - the channels will be tpicall integrated in our own construction, for optimum construction! A large range of channels (HM 8/ to HM 0/) plus locking plates (M to M ) is available. suitable for contact welding due to eas access from above. Select the most economic channel depending on the loading pages - 9 p. 8 HM 8/8 p. p. 8 HM 8/ HM / p. 0 p. HM 8/ HM / p. p. 0 HM 0/ HM Welded or bolted-on HAEN raming channels allow eas assembl on-site as well as for 'construction kit' structures. Note: If high load alternation (dnamic loads) occurs, hot rolled channels, e.g. HM 0/, are to be used.

33 HAEN RAMING CHANNES AND ACCESSORIES ight Dut raming Sstems for ight Dut HAEN s Product features There are matching HAEN T-head bolts and locking plates in a range of sies for all HAEN s. Several HAEN s take the same tpe of HAEN T-head bolt. or eample: 8/8 8 8 / 8/ 8 HS 8/ GWP 8/ Selection of HAEN T-head bolts and locking plates Tpe HS Tpe GWP pages - pages - A number of light dut HAEN raming channels are also available as HTA s for casting into concrete. page 9 HM or H Concrete HTA

34 HAEN RAMING CHANNES / HM / H /, = plain back = slotted back 8 Nominal dimensions Material, finish for eplan. see p. Stock no. ength: 000 mm Standard = To order = HM / wb A H / wb A Cross weight section G [kg/m],9,00 A [cm²],9, Order eample: Moment of inertia I [cm ],, I [cm ],8,8 Section modulus W [cm³],8,9 W [cm³],, Ma. perm. point loading ma,, ma Bending capacit at span [m] 0,0,00 [cm],0 HM / or Stock no see note on p.,0,0,9,,9,,0 0,8 HM / H / 0 0 Base channel for Sstem Series HAEN Sstem Series: page 0 - HAEN Series Cantilevers: page HAEN Series ittings: page Other channel data, design properties data Ma. tensile / transverse load Z Q Ma. load compression member -accessories SDM / Sound attenuator PA 8 H closer strip HPE / end cap Subject to alterations pages - page 8 page 9 page 0 page page

35 l HAEN T-HEAD BOTS AND ACCESSORIES for / HS 8/ Halfen T-head bolts incl. nut i = eft hand thread GWP 8/ ocking plates d b Halfen T-head bolts - load capacities 0, Thread Ø M 0 M M a grade., 9,, ength l S i i Order eample: HS 8/ - M M 0 80 Thread M M 8 M 0 M Order eample: GWP 8/ - M 0 - perm. load S Ma. pull out per T-head bolt grade 8.8, 9,, M 0 M M M 0 M M ength l Mat. ength l Mat. ength l Mat. ength l Mat. ength l Mat. ength l Mat Thread M M 8 M 0 M for mild steel channels grade. 0, 0, 0, A Thread M M 8 M 0 M loading capacit,,0,, Ma. longitudinal load per Halfen T-head bolt tightening torque [Nm] a,,,, grade 8.8,,,0 b,,,, tightening torque [Nm] d Bolt-accessories SIC ock washers for bolt HS 8/ Note: Do not eceed channel load capacit! See also p. - 9 (design properties). = Standard = to order SIC page Ma. pull out per T-head bolt grade A/A - 0, 9,, S for stainless steel channels grade A/A - 0 8,,, A-0 A-0 A-0 A-0 grade A/A - 0/0 0, 0, 0,9 Material/finish T-head bolts ( S. ) = h.d. galvanised, strength grade. = electroplated, strength grade. 8.8 = h.d. galvanised, strength grade = electroplated, strength grade 8.8 A-0 = Stainless steel grade A-0 A-0 = Stainless steel grade A-0 A-0 = Stainless steel grade A-0 A-0 = Stainless steel grade A-0 Ma. longitudinal load per Halfen T-head bolt A-0 0 A-0 0 A-0 0 A-0 0 A-0 0 A-0 0 A-0 0i A-0 0 A i tightening torque [Nm] 0 A-0 A-0 A-0 A-0 A-0 0 A-0 0 A-0 0 A-0 0 A-0 0 A-0 0 A-0 0i A-0 0 A i A-0 00 A-0 0 A-0 A-0 A-0 00 A-0 Calculation of bolt length lrequ. p. 9

36 HAEN RAMING CHANNES 8/ HM 8/ Nominal dimensions 8 8 Material, finish for eplan. see p. Stock no. Standard = To order = HM 8/ wb A A Cross weight section G [kg/m] A [cm²] Moment of inertia I [cm ] I [cm ] Section modulus W [cm³] ength: 000 mm Order eample: HM 8/ Material: Stainless steel W., Material order code HCR, on request. W [cm³] Ma. perm. point loading ma or Stock no. ma Bending capacit at span [m] 0,0,00 [cm],0,, 0,9,0 0,8,,8,0, 0, 0, see note on p. HM 8/ Other channel data, design properties data Ma. tensile / transverse load -accessories SDM / Sound attenuator PA 8 H closer strip Z Q pages - page 8 page 0 page

37 l HAEN T-HEAD BOTS AND ACCESSORIES for 8/ HS 8/ Halfen T-head bolts incl. nut d b 0, i = eft hand thread GWP 8/ ocking plates Halfen T-head bolts - load capacities a Thread Ø M 0 M M grade., 9,, ength l Order eample: HS 8/ - M M 0 80 High corrosion resistant Stainless steel T-head bolts HS 8/, order code HCR, on request. A a Thread Thread M M, M 8 M 8, M 0 M 0, M M, Order eample: GWP 8/ - - M 0 perm. load S i i S Ma. pull out per T-head bolt grade 8.8, 9,, M 0 M M M 0 M M ength l Mat. ength l Mat. ength l Mat. ength l Mat. ength l Mat. ength l Mat Thread M M 8 M 0 M for mild steel channels grade. 0, 0, 0, loading capacit,,0,, Ma. longitudinal load per Halfen T-head bolt tightening torque [Nm] grade 8.8,,,0 tightening torque [Nm] Bolt-accessories SIC ock washers for bolt HS 8/ Note: Do not eceed channel load capacit! See also p. - 9 (design properties). = Standard = to order b,,,, d 8.8 SIC page Ma. pull out per T-head bolt grade A/A - 0, 9,, S for stainless steel channels grade A/A - 0 8,,, A-0 A-0 A-0 A-0 grade A/A - 0/0 0, 0, 0,9 Material/finish T-head bolts ( S. ) = h.d. galvanised, strength grade. = electroplated, strength grade. 8.8 = h.d. galvanised, strength grade = electroplated, strength grade 8.8 A-0 = Stainless steel grade A-0 A-0 = Stainless steel grade A-0 A-0 = Stainless steel grade A-0 A-0 = Stainless steel grade A-0 HCR = Stainless steel W.9 HCR-0 Ma. longitudinal load per Halfen T-head bolt A-0 0 A-0 0 A-0 0 A-0 0 A-0 0 A-0 0 A-0 0i A-0 0 A i tightening torque [Nm] 0 A-0 A-0 A-0 A-0 A-0 0 A-0 0 A-0 0 A-0 0 A-0 0 A-0 0 A-0 0i A-0 0 A i A-0 00 A-0 0 A-0 A-0 A-0 00 A-0 Calculation of bolt length lrequ. p. 9

38 HAEN RAMING CHANNES s 8/8 and / HM 8/8 H 8/8 Nominal dimensions HM 8/8 H 8/8, HM / H / Base channel for Sstem 8 Series HM / H / Nominal dimensions Subject to alterations HAEN 8 Series ittings: page,, Material, finish for eplan. see p. HM 8/ wb sv ,, A H 8/ wb sv ,, A ength: 000 mm Order eample: Stock no. Standard = To order = pages - page 9 Cross weight section Moment of inertia Other channel data, design properties Material, finish data data Standard = G [kg/m] A [cm²] Cross weight section Ma. tensile / transverse load Section modulus page 0 SDM 8/ Sound attenuator Ma. perm. point loading [cm] Bending capacit at span [m] HM 8/ or Stock no see note on p. Moment of inertia -accessories Section modulus SDM 8/ Sound attenuator Ma. perm. point loading HPE 8/8 end cap page Bending capacit at span for Stock To eplan. no. order [m] see p. = ma G A I I W W 0,0,00,0 [kg/m] [cm²] [cm ] [cm ] [cm³] [cm³] [cm] HM / sv ,8,0 0,9,8 0, 0,9,0 0,0,0 0, 0, H / , 0,89 0,, 0, 0,89,0 0,0 0,90 0,0 0,8 sv ength: 000 mm Order eample: HM / - sv or Stock no see note on p. Other channel data, design properties -accessories Ma. tensile / transverse load I [cm ],0, I [cm ],0,98 W [cm³] W [cm³] 0,0 HPE / end cap pages - page 9 page 0 page,08 0,9,9, ma,0,0 ma,0, ma,9,,00 0,9 0,,0 0, 0, 8

39 l HAEN T-HEAD BOTS AND ACCESSORIES for s 8/8 and / HS 8/ Halfen T-head bolts incl. nut, i = left hand thread ength l i M M 8 M 0 M M 8 M 0 ength l Mat. ength l Mat. ength l Mat. ength l Mat. ength l Mat. ength l Mat A-0 0 A-0 A-0 A A-0 0 A A-0 0 A A A A A-0 0 i A A A A Oder eample: HS 8/ - M A-0 A-0 A-0 Calculation of bolt length lrequ. p. 9 GWP 8/ ocking plate d b a Halfen T-head bolts - load capacities M M8 M0 M Order eample: GWP 8/ -M8- grade.,,0, 9, Thread M M 8 M 0 perm. load S S Ma. pull out per T-head bolt grade 8.8, 8,, 9, Thread M M 8 M 0 grade. 0, 0, 0, 0, Thread M M 8 M 0 tightening torque [Nm],,0,,0,, loading capacit,9,8,0 for mild steel channels Ma. longitudinal load per Halfen T-head bolt grade 8.8 0, 0,,, tightening torque [Nm] Note: Do not eceed channel load capacit! See also p. - 9 (design properties). Assembl note: irst insert locking plate to channel, then screw in thread bar. A 8 a b d Bolt-accessories SIC ock washers for bolt HS 8/ SIC 8/ page Ma. pull out per T-head bolt grade A/A - 0,,0, 9, S for stainless steel channels grade A/A - 0,0, 8,, grade A/A - 0/0 0, 0, 0, 0, Material/finish T-head bolts ( S. ) = h.d. galvanised, strength grade. = electroplated, strength grade. 8.8 = h.d. galvanised, strength grade = electroplated, strength grade 8.8 A-0 = Stainless steel grade A-0 A-0 = Stainless steel grade A-0 A-0 = Stainless steel grade A-0 A-0 = Stainless steel grade A-0 Ma. longitudinal load per Halfen T-head bolt tightening torque [Nm] 8 = Standard = to order Assembl note: Insert locking plate inclined through channel chase. 9

40 HAEN RAMING CHANNES s 8/ and HM HM 8/ H 8/, 8 Material, finish for eplan. see p. Stock no. Standard = To order = Cross weight section G [kg/m] A [cm²] Moment of inertia I [cm ] I [cm ] Section modulus W [cm³] W [cm³] Ma. perm. point loading ma ma [cm] Bending capacit at span 0,0 [m],00,0 Nominal dimensions HM 8/ HM ( C 0), HM H 8/ 0 Nominal dimensions 0 9 HM 8/ wb A A H 8/ wb A A ength: 00 mm Order eample: HM 8/ Material: Stainless steel W. / W.9, Material order code HCR, on request. Other channel data, design properties Ma. tensile / Ma. load data transverse compression load member Z Q pages - page 8 page 9 page 0 Material, finish for eplan. see p. HM Stock no wb ength: 000 mm Standard = To order =,0 0,8 Cross weight section G [kg/m] 0,,, A [cm²] 0,9 0,8 0, Other channel data, design properties: pages - Moment of inertia I [cm ] 0,0 Order eample: HM ,, I [cm ], 0, 0,0 -accessories SDM 8/ Sound attenuator Section modulus W [cm³] 0,,0 0,98 or Stock no. W [cm³] 0,8,9,9 Ma. perm. point loading ma, or Stock no. 8,,0 ma see note on p. 0,0 [cm], 0,8 0,9 Bending capacit at span 0,9 0, 0, [m],00 0, 0,09 0,08,0 0, see note on p. Subject to alterations 0

41 l HAEN T-HEAD BOTS AND ACCESSORIES for s 8/ and HS 8/ Halfen T-head bolts incl. nut (not for HM ), i = left hand thread ength l i M M 8 M 0 M M 8 M 0 ength l Mat. ength l Mat. ength l Mat. ength l Mat. ength l Mat. ength l Mat A-0 0 A-0 A-0 A A-0 0 A A-0 0 A A A A A-0 0i A A A A Order eample: HS 8/ - M High corrosion resistant Halfen T-head bolts HS 8/, order code HCR, on request A-0 A-0 A-0 Calculation of bolt length lrequ. p. 9 GWP 8/ ocking plates for Chs. 8/ and (C 0) d b a Halfen T-head bolts - load capacities M M8 M0 M Thread M M 8 M 0 Order eample: GWP 8/ -M8- grade.,,0, 9, perm. load S S Ma. pull out per T-head bolt grade 8.8, 8,, 9, Thread M M 8 M 0 grade. 0, 0, 0, 0, A Thread M M 8 M 0 for mild steel channels tightening torque [Nm],,0,,0,, loading capacit,9,8,0 Ma. longitudinal load per Halfen T-head bolt grade 8.8 0, 0,,, tightening torque [Nm] Note: Do not eceed channel load capacit! See also p. - 9 (design properties). Assembl note: irst insert locking plate to channel, then screw in thread bar. 8 a b d Bolt-accessories SIC ock washers for bolt HS 8/ SIC 8/ page Ma. pull out per T-head bolt grade A/A - 0,,0, 9, S for stainless steel channels grade A/A - 0 grade A/A - 0/0 0, 0, 0, 0, Material/finish T-head bolts ( S. ) = h.d. galvanised, strength grade. = electroplated, strength grade. 8.8 = h.d. galvanised, strength grade = electroplated, strength grade 8.8 A-0 = Stainless steel grade A-0 A-0 = Stainless steel grade A-0 A-0 = Stainless steel grade A-0 A-0 = Stainless steel grade A-0 HCR = Stainless steel W.9 HCR-0 Ma. longitudinal load per Halfen T-head bolt tightening torque [Nm],0, 8 8,, = Standard = to order Assembl note: Insert locking plate inclined through channel chase.

42 HAEN RAMING CHANNES 0/ HM 0/ H 0/, Nominal dimensions 0 0 Material, finish for eplan. see p. Stock no. HM 0/ wb A H 0/ 08.. wb A Standard = To order = Cross weight section G [kg/m] 0, 0, A [cm²] 0, 0, Moment of inertia I [cm ] 0, 0,09 I [cm ] 0, 0, Section modulus W [cm³] 0, 0, W [cm³] 0, 0, Ma. perm. point loading ma,, ma Bending capacit at span [m] 0,0,00 [cm],8, 0, 0,9 0,0 0,0,0 0,0 0,0 HM 0/ H 0/ 0 9 ength: 000 mm Order eample: Other channel data, design properties data HM 0/ or Stock no see note on p. pages - Subject to alterations

43 HAEN T-HEAD BOTS AND ACCESSORIES for 0/ HS 0/ Halfen T-head bolts incl. nut, ength l M ength l Mat. M 8 ength l Mat. M 8 ength l Mat A A A A Oder eample: HS 0/ - M Material / finish Halfen T-head bolts ( p. ) = electroplated, Strength grade. A-0 = Stainless steel grade A-0 Calculation of bolt length lrequ. p. 9 GWP 0/ ocking plates for 0/ d b a A a b d Thread Thread M M 9 M M 9 Order eample: GWP 0/ -M- Bolt-accessories SIC 0/ ock washers Halfen T-head bolts - load capacities Thread Ø Ma. pull out per T-head bolt grade. S perm. load S grade. Thread M M for mild steel channels Ma. longitudinal load per Halfen T-head bolt loading capacit,,9 tightening torque [Nm] M, 0, M 8,0 0, 8 Note: Do not eceed channel load capacit! See also p. - 9 (design properties). Ma. pull out per T-head bolt S grade A - 0,0, SIC 0/ page for stainless steel channels Ma. longitudinal load per Halfen T-head bolt grade A - 0 0, 0, tightening torque [Nm] 8 = Standard = to order Subject to alterations

44 HAEN RAMING SYSTEMS ACCESSORIES Threaded Rods, Heagon Head Bolts, Nuts, Washers GWS Threaded rod DIN 9 HSK He head bolt DIN 9 or EN 0 (without nut) S He head bolts are used in combination with HAEN locking plates ( pages9-) S m electroplated A ength oad strength grade. Stainless steel A cap. Thread Thread M M 000, M 8 M 8 000,0 M 0 M 0 000, M M 000 9, M M 000, M 0 M 0 000,0 M 000 8,8 Order eample: GWS - M electroplated, s.gr. 8.8 Dimension M M M 8 M 8 0 M 0 0 M 0 0 M 0 M 0 0 M 0 0 M M M 0 M 0 M 0 M 0 M 80 M 90 M 0 M 0 M 90 A Stainless steel A Dimension M 8 M 0 0 M 0 M M 0 M 0 M 0 M 80 M 0 M 0 M 90 S DIN S EN MU A S/m S/m e Heagon nut electroplated s.gr. 8 Stainless steel A DIN ISO DIN 9 or Thread Thread ISO 0 M M 0/ 0/, (= DIN EN 0) M 8 M 8 /, /,,0 M 0 M 0 / 8 / 9, 9, M M 9/0 8/,9 M M / /,, e M 0 M 0 0/ 0/9, M /9 /, A S/m S/m e Stainless steel A DIN EN Thread M 8 /, /,,0 M 0 / 8 / 9, 9, M 9/0 8/,9 M / /,, US Washers DIN 0, 90 d D S US Washers DIN d D S HJV Adjustment coupler DIN d d electroplated for bolt M M 8 M 0 M M M M 0 Order eample: US - M - -DIN 90 electroplated for bolt M M 8 M 0 M M M 0 M M M 0 h.d. galvanised for bolt M 8 M 0 M 0 M M M M Order eample: US - - M - DIN h.d. galvanised Tpe Ma. recomm. load t A D d s Stainless steel A for bolt, M 8 8, M 0 0 0,,, M M 0 A D d s Stainless steel A for bolt M,, M 8 8,, M 0 0, M, M 0 M 0 M 0 8 A D d s Stainless steel A for bolt 8,, 0,, 0 A t b d Stainless steel A Tpe 0, 8 0, 0 0,0 b Tpical installation: fiing of a suspended load under a reinforced concrete bridge. Cross section HJV

45 HAEN RAMING SYSTEMS ACCESSORIES Coupler Sleeves, Ring Nuts, Square washers VBM Coupler sleeves, rounded D - -A D oad cap. electroplated Stainless steel A Thread Thread M M 0/0, M 8 M 8 / 0,0 M 0 M 0 /, M M /0 0 9, M M / 0, M 0 M 0 / 0,0 Order eample: VBM - A - M OES Ee sleeve d M - d electroplated Thread M M 8 8 M 0 0 M M Order eample: OES - - M 80 oad cap.,,00,00, 8,0 SKM Heagonal rod coupler with view hole SPH f s Turnbuckle with righthand / lefthand thread D ock washer Application: to secure HAEN T-head bolts against unscrewing during fitting. - -A S oad cap. h.d. galvanised Stainless steel A Thread Thread M 0 M 0 0, M M 0 9, M M 0, Order eample: SKM - - M -A -A Stainless steel A Stainless steel A Thread M ength M 0 M M 9 M 9 f = min. Screw-in-depth M: 0 mm M: mm M M Perm. load: kn M M Perm. load: 0 kn Order eample: SPH - A - M SIC - electropl. Thread M ength M 0 M -A Stainless steel A Stock no. Stock no. Tpe Dimension SIC-0/0 - SIC-0/0-A 0/0 M, M0 SIC-0/ - SIC-0/-A 8/ 0/ M SIC-8/ - SIC-8/-A 8/ M SIC- 9/ 0 - SIC-9/0-A 9/0 M SIC-8/- SIC-8/-A 8/ 0/ M, M0 SIC-8/ - SIC-8/-A 8/ M8, M0 SIC-0/ - SIC-0/-A 0/ M8 Order eample: SIC - 8/- Assembl diagram: HAEN HAEN T-head bolt SIC ock washer D für M its to Halfen bolt D für M RM Ring nut DIN 8 VUS VUS 0/ for channel 0/; HZA a / VUS 9/0 for channel /, 9/0 a for channel /, 0/0 a VUS /9 for channel /8, /9 a VUS / for all Chs. Series a M Square washers VUS / Order eample: - d C, electropl. Thread M 8 0 M 0 M 0 M d M 0 0 oad cap.,,,,0,0 Order eample: RM - - M Recomm. maimum working load with centre pull out Dimension D for finish - / -A Recomm. maimum centre pull out in accordance with DIN 8 - -A a b d h.d. galvanised Stainless steel A for bolts: for bolts: M 0 M M M 0 0 d M M 0 0 b M 0 M 0 M M d M M b M 0 M 0 M M 0 0 M 0 M d b M 0 M 0 M M d M M b M 0 M 0 M M 0 0 d M 0 M b M M 0 0 VUS / - - M 0

46 HAEN RAMING SYSTEMS ACCESSORIES End Cap, Closer Strip end cap (plastic) HAEN Tpe HPE / Colour: blue Tpe HPE Colour: black Tpe HPE / Tpe HPE / Colour: black Designation HPE / HPE / HPE 0/0 HPE / HPE / HPE / HPE 8/8 HPE / Order eample: or Stock. no. Stock no HPE / fits to / / 0/0 / / / 8/8 / Application of the end cap: HAEN PA closer strip Tpe: Qual. / finish: PVC, hard ( Plastic) ( KS) Qual. / finish: steel, pregalvanised ( sv) PA 9 9 white PA, gre PA 8 H,, gre fits to channel: fits to channel: fits to channel: 0/0, 0/0 / /, 8, 8/ all Chs. Series Tpe Order eample: or Stock no. Assembl diagram: ength PA - - KS PA - - sv PA - - KS PA - 8H - KS PA Section slit to prevent dirt getting into interior of channel. = Standard Stock no PA - - KS HAEN raming channel e.g. HM /

47 HAEN RAMING SYSTEMS ACCESSORIES HAEN Beam Clamps HVT, U-clamp Plate, Halfen T-head bolt for -back Assembl Beam clamp, used in pairs for s /, / and / D Ø 0 0 S 8 HVT - 8 load capacit per clamp pair:, kn Clamp thickness: mm, Beam clamp, used in pairs for s / D, / and /8 HVT - 8 load capacit per clamp pair:, kn Clamp thickness: mm Designation Stock no. Designation Stock no. Designation HVT HVT A for H /:, kn per clamp pair KUS U-clamp plate, fits to all HAEN s Series HS / Halfen T-head bolt incl. nut, for all Chs. Series Insertion through slotted channel back also possible for channels H /8 and H / Halfen T-head bolts - load capacities Ma. pull out per T-head bolt for mild steel channels h.d. galv., str.gr. Tpe Stock no. KUS Thread Ø grade. grade. tightening torque [Nm] M 0, 0, M 8,0 0, Note: Do not eceed channel load capacit! See also pages - 9 (design properties). 0 HVT HVT A S grade A - 0 e.g. Chs. /8 or / Note: T-head bolts HZS / and / for s / to /8 page. Beam clamp, used in pairs tightening torque Nm for all s /.. 0 HVT - 89 load capacit per clamp pair:,0 kn Clamp thickness: mm Stock no. HVT HVT A = h.d. galv., str.gr. A = Stainless steel A = packing unit [pieces] Assembl diagram U-clamp plate M 0 M M 0 M ength l Mat. ength l Mat. ength l Mat. ength l Mat. A-0 A-0 0 Ma. longitudinal load per Halfen T-head bolt KUS Ma. pull out per T-head bolt, 9, for stainless steel channels Ma. longitudinal load per Halfen T-head bolt grade A - 0 0, 0, Material / finish Halfen T-head bolts ( p. ) = h.d. galv., str.gr.. = electropl., str.gr.. A-0 = Stainless steel A-0 tightening torque [Nm] = Standard = to order

48 HAEN RAMING SYSTEMS ACCESSORIES Beam Clamps Beam clamps Sstem Series Beam clamp with teeth for interlocking load transmission, used in pairs 9 Ø 8 HCS TK HCS TK - HCS TK - load cap. per clamp pair -8kN,depending on bolt load cap. per clamp pair 8 kn load cap. per clamp pair kn Designation Stock no. Designation Stock no. Designation Stock no. HCS TK- HCS TK-- HCS TK-- Application eamples: = h.d. galvanised = packing unit [pieces] Ma. tightening torque 0-90 Nm, depending on bolt Important for assembl: h = -0 mm lange thickness Beam flange width + ( 0 mm) beam clamps used for one fitting h 0 mm 0 mm Beam clamps used in pairs Ma. tightening torque 90 Nm Ma. tightening torque Nm 8

49 HAEN RAMING SYSTEMS ACCESSORIES Beam Clamps KP - S Beam clamps, St - forged a b feuerverinkt Tp Bestell-Nr No. 0 No. No Heelwidth n without heel 0 for T-head bolt Ø l a M 0,0 M 0, M 0 0,0 b Dimensions c 8 Ø d 8 8 h k m 9 8,0,,,0 Perm. load at perm. = N/mm ²,, 0,0 recommended use with other beams, s flange thickn. t Standard Chs. I S A, A S - S 9 n Ø d No No Order eample: without heel M 0, 9,, M, 9 9,, without heel M, 9 9,, KP - S - Nr. - or Stock no m Assembl diagram : Tpe KP - S c No ,0 0,0 0, A - A - A - Heel k h HAEN raming channel oad scheme KP - S KP - 0 Beam clamps (formerl DIN 8) To be discontinued T-head bolt M 80 is required Do not eceed channel load capacit! Check flange thickness first! h.d. galvanised Stock no. Tpe / / / / / / h Clamping heigth h HAEN T-head bolt e.g. HS 0/0 Washer e.g. US DIN HAEN Beam clamp e.g. KP HAEN raming channel e.g. H 0/0 HAEN ocking plate e.g. GWP 0/0 Threaded rod with lock nut and square washer VUS Perm. load =,0 T-head bolt M 0, grade. =, T-head bolt M 0, grade 8.8 Order eample: KP - 0/0 - or Stock no oad scheme KP - 0 e.g. H 0/0 recommended use with Standard channel Standard channel crane / running I I PB rails A, S, S A00, S 9, A A0, S S The heel preventes twisting of the beam clamp b slotting into the channel slit. tg HAEN raming channel Assembl diagram : Tpe KP - 0 9

50 HAEN RAMING SYSTEMS ACCESSORIES Sound Attenuator, Ductwork Suspensions SDM Sound attenuator d cm cutting or roll b Ø Material: Elastomer - technical qualit (EPDM) ± Shore Standard Tpe b/d Stock no SDM /8 - roll 0000 SDM /8 - cm - piece 0000 SDM / - roll SDM / - cm - piece SDM 8/ - roll SDM 8/ - cm - piece Order eample meter length: Order eample cm - piece: its to with slid width Tpe its to threaded rod Please indicate length [m] when ordering. The product is kept in stock length of 0m SDM/-roll, m or Stock no. SDM / - cm - piece or Stock no. 0/0, / /8 8 / 8/8, /, 8/ Ø M Ø M 0 Ø M , m Assembl diagram SDM: SDM itting elements for ductwork suspensions iing point to concrete constructions: HAEN raming channel ( p. 9-9) to steel beam: beam clamp Threaded rod electroplated Seite Sound attenuator Material: EPDM (see above) HAEN slotted channel h.d. galvanised, pre-galvanised to accomodate load in accordance with table p. - Washers, nuts electroplated p. end cap HPE p. 0

51 HAEN RAMING SYSTEMS Ductwork Suspensions Selection of s, perm. loads Assembl diagram: see detail / B (total) / Using dowels observe construction regulations for concrete tension one! Observe fire regulations! Acc. to DIN 0 reduced load capacities! Detail: iing to HAEN raming channel HAEN raming channel e.g. HTA 8/ ( p. 9) ocking plate GWP 8/ ( p. ) Washer US ( p. ) 00 mm 00 mm HPE ( p. ) Threaded rod GWS with lock nut ( p. ) Eample: Tpe H 0/0 H / H / H 8/8 H / H 8/ 0 H 0/0 0 (total) Threaded rod [kg] Thread 0,0 000 M-M 8,0 800 M-M,0 00 M-M,0 00 M0-M, 0 M0-M, 0 M8 q = 0 kg/m H /, Sound attenuator Tpe SDM /8 SDM /8 SDM / SDM 8/ SDM 8/ SDM 8/ Ch. End cap Tpe HPE 0/0 HPE / HPE / HPE 8/8 HPE / (total) H / 8 = weight per metre suspension distance [kg/m m] HAEN channels Tpe HTA 0/ HTA 8/ HTA 8/ HTA 8/ HTA 8/ HTA 8/, iing to concrete B Dowel (acc. to official approval certificate) Press. one Tension one M - M M - M M M 0 M 0 M 8 8 H 8/8 8 M M 0 M 0 M 8 Ductwork 000/ 00 mm Wall thickness 0 mm Weigth per metre 0 kg/m Suspension distance, m (total) 0,0, 0,0 kg ~, kn selected: Ch. H 8/8 (perm. (total) =,0 KN) H / iing to Steel beam Beam clamp HCS TK- ( S. 8) HAEN raming H 0/0, HS 0/0 M Beam clamp HVT - 8 ( p. ) HAEN raming H / H 8/ 8

52 HAEN RAMING SYSTEMS Materials, inishs HAEN s Heav Dut raming Sstems Medium Dut raming Sstems ight Dut raming Sstems Material / finish: hot rolled pages - cold rolled pages - pages - Order code mill finish wb Hot rolled: Material SJRG (RS t -), DIN EN 00; cold rolled: Material SJR (St -), DIN EN 00 mill finish Material SJR (St -), DIN EN 00 resp. equivalent steel grade acc. to British Standard BS 9, Sect.., 99 mill finish Material SJR (St -), DIN EN 00 mill finish hot-dip galvanised DIN EN ISO suitable for outdoor applic. pre-galvanised EN 0 suitable for inddor applic. Stainless steel DIN EN 0088 resp. DIBt approval certificate Z-0.- sv A A HCR Hot rolled: Material SJRG (RSt -), DIN EN 00; Cold rolled: Material SJR (St -), DIN EN 00 hot-dip galvanised, inc coating min. 0m Material. /.0, DIN 0 Material SJR (S t -), DIN EN 00 resp. equivalent steel grade acc. to British Standard BS 9, Sect.., 99 hot-dip galvanised, inc coating min. 0m Material e E 80 G Z NA EN 0 pre-galvanised, inc coating min. 0m Material. /.0, DIN 0 Material SJR (St -), DIN EN 00 hot-dip galvanised, inc coating min. 0m Material e E 80 G Z NA EN 0 pre-galvanised, inc coating min. 0m Material.0 DIN 0 Material. /.0, DIN 0 HCR = high corrosion resistant Stainless steel; Material.9 or., DIN EN 0088, for s 8/, 8/ and 9/0 on request.

53 HAEN RAMING SYSTEMS HAEN T-head Bolts, Assembl T-head bolts, : Halfen bolts for increased securit during assembl: The new S- shape of the head provides additional securit for correct locking of bolt inside the channel; avoiding an risk of turning during assembl, even when differing profile widths occur due to manufacturing tolerances. During the period of change to the new bolt shape, both bolts are supplied. Patents pending. Material / finish: Tpes HS, HSR, HZS incl. nut pages 9-9,, - HalfenT-headbolts ocking plates Tpe GWP pages 9-9,, - Heagon head bolts Tpe HSK DIN 9 resp. EN 0 page Heagon nut Tpe MU DIN 9 or DIN EN 0 page Order code hot dip galvanised, inc coating min. m, strength grade. according to DIN ISO hot dip galvanised, inc coating min. m, strength grade 8 acc. to DIN ISO Hot-dip galvanised DIN 09, for threaded parts DIN Part 0 Zinc electroplating DIN 09, DIN EN 0, DIN EN ISO 0 Stainless steel DIN EN 0088 resp. DIBt approval certificate Z A A-0 A-0 A A-0 A-0 HCR hot dip galvanised, inc coating min. m, strength grade 8.8 according to DIN ISO inc electroplating, inc coating min. m, strength grade. according to DIN ISO inc electroplating, inc coating min. m, strength grade 8.8 according to DIN ISO Grade A-0, DIN, Part Grade A-0, DIN, Part Grade A-0, DIN, Part Grade A-0 DIN, Part Material No..9, grade HCR-0 acc. to DIN EN ISO 0- (on req.) inc and chrome electroplating, inc coating min. m Stainless steel A inc electroplating, inc coating appro. m, strength grade 8.8 according to DIN ISO Stainless steel A - 0 inc and chrome electroplating, inc coating min. m, strength grade 8 according to DIN ISO Stainless steel A Stainless steel A

54 HAEN RAMING SYSTEMS HAEN raming s, plain back Heav Dut raming Sstems ight Dut raming Sstems Medium Dut raming Sstems HM../.. e e HM /8 HM / HM 0/0 HM 0/ HM /8 D HM / D HM 0/0 D HM 0/ D Heav Dut raming Sstems HZM../.. cold rolled hot rolled Tpe HZM 8/ NEW! HZM 9/0 NEW! HM 9/0 HM 0/ HM 0/0 HM 8 HM (C0) HM / HZM / HM / HZM / HM /8 HM / HM / D HZM / D HM / D HZM / D HM / D HM / HM 8/ HM (C0) HM 8/8 HM / HM 8/ HM 0/ Standard to order not available wb = mill finish sv = pre-galvan. = h.d. galvan. HAEN raming channels, plain back: toothing HM../.. weight Cross section NEW! hot rolled cold rolled p. 0 A A G [kg/m] 8,8,9,,, 9,9,,,,,0,08,,,,,,80,9,8,9,,,0,8,8,9, 0,, 0,8,0 0, A [cm²],,,,0,, 8,,9,09,98,9,,,9,98,,,0,,9,,,,9, 8,,9, 0,9,,0, 0, HZ / Centre of load e [cm],,8,,,8,0,00,0,,,,,8,,,,8,,,,,,,0,0,0,0,0 0,9,8,8 0,88 0, e [cm],,,,0,8,0,00,0 0,9 0,88,,0,, 0,9,9, 0,8 0,8,80,9,,,0,0,0, 0,9 0,8,, 0, 0,8 Medium Dut raming Sstems cold rolled Moment of inertia I [cm ],99 9,,,0,,9,9,,0 0,8, 0,9 0,0,0 0,9 0,8 0, I [cm ] 8,0,,,8 0,0,,9 8,, 8, 0,,9,,0,,,,9,0,0 8,,0,9 9,,,9 9, 9,0,,,00,0,8 8,, 8,8, 0,,,0 08,,,8,0,,0,8, 0, HM /.. W [cm³],,9,,,, 9,,,9 0,9,,,9,9,0,0,9 0,9 0,9 9,,9 8, 8,,9,8,,8 0,8 0,,08 0, 0, 0, Section modulus W [cm³],08 9,9,8,9, 8,,,8,,,,0,,0,,,,8, 8,, 8,9 8,90,,,9,, 0,8,9 0,9,0 0, W pl, [cm³] 8,8,09,,9,88,,8,9,,,,0,,,,,,0,, 8,8,9,,8,8,,, 0,, 0,89 0, 0, ma. perm. point loading ma ight Dut raming Sstems cold rolled ma,0,0,0,,0,0,0,,0 8,0,9,8,,,,,,,,,,,,,,,,8,,0,,9, HM../.. [cm] to follow see right page

55 HAEN RAMING SYSTEMS HAEN raming s, plain back Heav Dut raming Sstems ight Dut raming Sstems Medium Dut raming Sstems e e = HM /8 HM / HM 0/0 HM 0/ = HM /8 D * HM / D * HM 0/0 D * HM 0/ D * = HZM 8/ HZM 9/0 [m] Bending load capacit at span [m] Observe minimum distance ae between end and load point (T-head bolt, locking plate): Heav and medium dut framing sstems: ae 0 mm light dut framing sstems: ae mm Do not eceed T-head bolt load capacit (p. 0 - ) and ma. point loading at channel slot (p. + ). The lowest value is base of calculation. q [m] matching HAEN T-head bolts matching ocking plates q [kn/m] Tpe Thread Tpe Thread 0,0m,00m,0m 0,0m,00m,0m 0,0m,00m,0m,0,,, 8,,0,0,0 9,0 HS / HSR /8 M0-M0 GWP /8 M-M ,,,,,0,, 8,, HS / HSR 0/0 M0-M0 GWP 0/0 M 8-M 0-,,,,9, 0, 9,0,, HS / HSR 0/0 M0-M0 GWP 0/0 M 8-M -,, 0,9,0 0, 0,9,, 0, HS / HSR 0/ M0-M GWP 0/ M -M -,00m,00m,00m,00m,00m,00m,00m,00m,00m,,,,,9,9,,, HS / HSR /8 M0-M0 GWP /8 M-M0 8-9,,, 0,,,0,,,8 HS / HSR 0/0 M0-M0 GWP 0/0 M 8-M 0-,,,,, 0,9,8,9 0,8 HS / HSR 0/0 M0-M0 GWP 0/0 M 8-M -,, 0,, 0,8 0,,, 0, HS / HSR 0/ M0-M GWP 0/ M -M - 0,0m,00m,0m 0,0m,00m,0m 0,0m,00m,0m,, 0,,0 0,8 0,,, 0, HZS / HS 8/ M-M GWP 8/ M-M0 -, 0, 0,, 0, 0,,0,0 0, HZS / HS 9/0 M GWP 8/ M 8-M - HM 9/0,,,0,, 0,,,, HS 0/0 M0-M0 GWP 0/0 M 8-M - HM 0/,,0 0,,9 0, 0,,, 0, HS 0/ M0-M GWP 0/ M -M - HM 0/0,9,,0,,,,8,9, HS 0/0 M0-M0 GWP 0/()0 M -M 8-9 HM 8,, 0,, 0,9 0,,, 0, HS 0/0 M0-M0 GWP 0/()0 M -M 8-9 HM (C0),8 0,9 0,, 0, 0,8,, 0, HS 0/ M0-M GWP 0/ M -M = 0,0m,00m,0m 0,0m,00m,0m 0,0m,00m,0m HM /,,,,0,0,0,0,,8 HZS /, / M 8-M GWP / M -M HZM /,,,,0,0 0,9 0,,, HZS /, / M 8-M GWP / M -M HM /,8 0, 0,, 0, 0,,0,0 0, HZS /, / M 8-M GWP / M -M HZM /, 0, 0,, 0, 0,,0,0 0, HZS /, / M 8-M GWP / M -M =,00m,00m,00m,00m,00m,00m,00m,00m,00m HM /8 * HM / * 8,,,,,,,,9,,, 0, 8,,,,, 0, HZS /, / HZS /, / M 8-M M 8-M =,00m,0m,00m,00m,0m,00m,00m,0m,00m HM / D * HZM / D * HM / D * HZM / D *,,0,,,9,,,,, 0, 0,,,,,,, 0, 0,,8, 0, 0,,9,,8,8,,,,,, 0, 0, HZS /, / HZS /, / HZS /, / HZS /, / M 8-M M 8-M M 8-M M 8-M HM / D *, 0,,,,,,8,, HZS /, / M 8-M = 0,0m,00m,0m 0,0m,00m,0m 0,0m,00m,0m HM / HM 8/ HM (C0) HM 8/8 HM / HM 8/ HM 0/,9, 0,9,9, 0,8 0,,9 0, 0, 0,9 0, 0, 0,0,0 0,9 0,0 0, 0, 0,09 0,0,0,0 0,8, 0,8 0,9 0,, 0, 0,09 0, 0,0 0, 0,0 0, 0, 0,0 0, 0, 0,0 0,0,8,,0,8,, 0,,9 0,9 0,, 0,8 0, 0,0, 0,0 0,08 0, 0, 0,0 0,0 HS 8/ HS 8/ HS 8/ HS 8/ HS 8/ HS 0/ M0-M M0-M M -M M -M M -M M -M 8 GWP / GWP / GWP / GWP / GWP / GWP / GWP / GWP 8/ GWP 8/ GWP 8/ GWP 8/ GWP 8/ GWP 8/ GWP 0/ M -M M -M M -M M -M M -M M -M M -M All load bearing values are calculated elastic-plastic according to DIN Part safet coefficient =,. Defleion l/ 0. Other accessories see page M -M - M -M0 - M -M0 0- M -M0 8-9 M -M0 8-9 M -M0 0- M-M - Acc. to ma. perm. point loading: Ma = ma. bending load capacit on the channel lips. *) Possible bulging, tilting and buckling must be prevented b appropriate measurements.

56 HAEN RAMING SYSTEMS HAEN raming s, slotted e e Standard to order not available Tpe wb = mill finish sv = pre-galvan. = h.d. galvan. A A weight G [kg/m] Cross section A [cm²] Centre of load e e [cm] [cm] Moment of inertia I [cm ] I [cm ] W [cm³] Section modulus W [cm³] W pl, [cm³] ma. perm. point loading ma ma [cm] H.D. r. Ss. ight D. r. Ss. Medium Dut r. Sstems H 0/ 0 HZ / H / HZ / H / HZ / H /8 H / H / H 8/8 H / H 8/ H 0/ HAEN raming s, slotted: H 0/0 Hole sies and spacing cold rolled All load bearing values are calculated elastic-plastic according to DIN Part safet coefficient =,. Defleion l/ 0. Heav Dut raming Sstems A a Other hole sies and spacings on request; e.g. 8/8 also with R Ø or 0 ever 0 mm. D HZ /,,,,,,,9,,00, 0, 0,8 0, 0,,09,98,90,9,8,0,99,,8 0,89, 0,,9,0,,8,,,9,,8,9,9 0,9 0,,9,9,99,9 0,9 0,9,0,0,,, 0, 0,9,,0,0,8 0,99 0,9,0,,,9 9, 9,0,,,9,0,,8,9,,,,,98 0,9,,,0 0,, 0, 0,89 0,, 0 0,, 0,0 0,98 0,,9 0,09 0, 0, 0, 0,9, Observe minimum distance ae between end and load point (T-head bolt, locking plate): Heav and medium dut framing sstems: ae 0 mm light dut framing sstems: ae mm Medium Dut raming Sstems H/HZ /.. ight Dut raming Sstems H.. /.. Heav Dut raming Sstems Medium Dut raming Sstems ight Dut raming Sstems D A a D A a D A a H H / HZ H 0/ / 8 0 / / / 8 0 8/8, 0 / 8 0 /, 0 / 8 0 8/ 9 0 / / 9 0 / 0 0 0, 0,0,8,9 0,89 0,8 8,8,,,,,8,,9 8,0,,8,,8,0,,,0,,,,,,,,,,,0,0,0,0,0,0 8,0 to follow see right page

57 HAEN RAMING SYSTEMS HAEN raming s, slotted H.D. r. Ss. ight D. r. Ss. Medium Dut r. Sstems e e H 0/ 0 HZ / H / HZ / H / HZ / See note on page. = [m] Bending load capacit at span [m] Do not eceed T-head bolt load capacit (p. 0 - ) and ma. point loading at channel slot (p. + ). The lowest value is base of calculation. Acc. to ma. perm. point loading: Ma = ma. bending load capacit on the channel lips. *) Possible bulging, tilting and buckling must be prevented b appropriate measurements. q [m] q [kn/m] 0,0m,00m,0m 0,0m,00m,0m 0,0m,00m,0m,8,,,,,,9 8,,, 0, 0,,,,, 0, 0,,,,,,,,,,8, 0, 0,,0, 0,8 0,8 0, 0,,, 9, 9,,, matching HAEN T-head bolts matching ocking plates Tpe Thread Tpe Thread,, 0,8 0,8,, 0, 0, HZS /, / HZS /, / HZS /, / HZS /, / M 8-M M 8-M M 8-M M 8-M GWP / GWP / GWP / GWP / =,00m,00m,00m,00m,00m,00m,00m,00m,00m H /8 H /,,,,,,0,,,8,, 0,,,,,8, 0, HZS /, / HZS /, / M 8-M M 8-M GWP / GWP / = 0,0m,00m,0m 0,0m,00m,0m 0,0m,00m,0m H / H 8/8 H / H 8/ H 0/,, 0,90 0,9 0,9, 0, 0,0 0, 0,0 0,88 0, 0,8 0,08 0,0,, 0,8 0, 0,, 0, 0, 0,0 0,0 0, 0,9 0,0 0,0 0,0,,, 0, 0,,, 0, 0,8 0,08 0,9 0, 0,9 0,08 0,0 HS HS HS HS HS 8/ 8/ 8/ 8/ 0/ M0-M M -M M -M M -M M -M 8 GWP 8/ GWP 8/ GWP 8/ GWP 8/ GWP 0/,8,8,8, HS 0/0 GWP 0/0 M0-M0 GWP 0/0 HZS /, / M 8-M GWP / M -M M -M M -M M -M M -M M -M Other accessories see page M -M 8-9 M -M M -M - M -M0 8-9 M -M0 8-9 M -M0 0- M -M -

58 HAEN RAMING SYSTEMS oad Capacit Values for HAEN raming s oad capacit values for welded-on HAEN raming channels Tpe Welding seams iing space hot rolled cold rolled HM /8 HM / HM 0/0 HM 0/ HZM 8/ HZM 9/0 HM 0/0 HZM / HZM / HM / HM / HM / HM 8/ HM 8/ NEW! NEW! aw lw oad capacit Q Z tensile transverse ew load load 0 0 Z Q 00,0 9, 00,0,9 00,0,0 0,, 00,0, 0 8,0, ,,,,,,,8,,9,,,,,,, longitud. tensile load, ever angle,0 8,0,0,0 Values do not appl for Stainless steel channels p. 0 Values do not appl for Stainless steel channels p. oad capacities given for cold rolled channels, welded in cold formed areas, refer to secondar, non safet-relevant applications. Perm. loads in longitudinal direction for smooth (untoothed) framing channels pages 0 - HAEN raming channels Tpe HM welded to steel parts aw aw pull area Z Q transverse pull area 0 Q HAEN raming channels Tpe HM bolted to concrete elements transverse pull area 0 0 pull area Z 0 0 The transverse capacit values appl for transverse load on front edge of the channel. Where the load is higher (e.g. spaced fiing), the additional bolt bending moment should be included and superimposed on the transverse pull loads. Eample p. 9 ew Z ew Q ew Pull loads in the least effective position oad spacing ew Transverse pull loads in the least effective position oad spacing ew ew Z ew Q ew Q transverse pull area 0 Q Q 8

59 HAEN RAMING SYSTEMS oad Capacit Values for HAEN raming s Perm. bending moments for T-head bolts taken from front edge of channel Thread M M 8 M 0 M M M 0 M M M 0 M T [Nm],0,0 0,0,, 8, 9,,9 99,9 P. l = sk e M T Note: The bending moment of T-head bolt MT must not eceed the perm. elbow support moment MS of HAEN. Perm. elbow support moment for HAEN s oad capacit values for HAEN raming channels as compression members Buckling detection acc. to DIN = permitted working load Part safet factor for forces f =,, E = N/mm² - load applied to = permitted working load point P Part safet factor for forces f =,, E = N/mm² HAEN data Perm. working load at member length : A e I W Wpl i min Tpe [cm²] [cm] [cm ] [cm³] [cm³] [cm] HM /8,,,99, 8,8, 0,,,,9 9,, 8,,, 0, HM /,,8 9,,9,09,,, 9,0, 0,0,,9,,8, HM / D,,,9,,, 8,,9,,8 0,9,,,,,8 HM 0/0,,,,,,,9,9, 8,,8,,, HM 0/,0,,0,,9 0,8, 8,9,,,,8 S HM 0/0,,8 8,,9,,,9 9,,, 8,,,,,,8 H 0/0,,9,,,8,8 9,,, 9,,0,,,,8, Note: At higher ecentricit, the ma. load should be calculated in terms of buckling in accordance to DIN grade 8.8 A - 0 A - 0 A - 0 A - 0 M T [Nm] M T [Nm] M T [Nm],,8,8,, 9,,9 8, 8,,,,8,0 8,8 8,,,,,,,8 9, HZ / HM/HZM / HM/HZM /D HZ/H / HM / H / HM 8/8 H 8/8 HM / H /,09,,,90,9,,,8,0 0,89 /8 / 0/0 0/ 8/ 9/0 0/0 8 MS [Nm] ,0,0 0,0,,8,,8,0,8,8,9,8,9,9,,8,,,0, 0,9 0,,9 8,,9,8,9,08 0,9 0, 0,,,,0,,,, 0,89 0, M S / / 8/ 8/8 / 8/ 0/,,,8,,, 0,99 0,9 0,9 0,9,8,9,,,, 8,,,, MS [Nm] ,,,,,8 9,,,9,,9,,, 9,8 8,,,,,,8 Eample: HM / K = 0 e.g. HSR 0/0 M 0 k. 8.8 Q =,0 kn HAEN HM / perm. M S = 0 Nm > 0 Nm perm. Q =,90 kn >,00 kn (page 8) HAEN HSR 0/0 - M, k. 8.8 perm. M T = Nm > 0 Nm actual Q =, ( - 0/) ( page S ) =,8 kn >,00 kn or bolt bending with additional pull, diagonal pull or transverse pull, the loads should be overlaid: Z, Q perm. Z, Q ( - M/ perm. M) perm. Z, Q = perm. pull resp. diagonal pull resp. transverse load perm. M = perm. bending moment T-head bolt Z, Q = eisting pull resp. diagonal pull resp. transverse load M = eisting bending moment T-head bolt, 8, 0,,,,,8,,, 9,,,,,,8,0,,,,8,,,8,,0,,,,,, 9,,,9, 0,, 9

60 HAEN RAMING SYSTEMS Heav and ight Dut raming Sstems HAEN T-head bolts Tpe HS, HSR - load capacities Pull out loads Note: S Generall the ma. loads of HAEN s are lower than those of T-head bolts ( pages - 9). T-head bolts Tpe HS ongitudinal loads T-head bolts Tpe HSR with nibs Tpe HS: The ma. load is a theoretical value and depends on a number of other factors. Tpe HSR: Because of T-head bolt nibs a friction-tpe connection is assured. Important: Do not eceed tightening torque of T-head bolt. T-head bolts Tpe HZS 8/ and 9/0, nibbed. its to channels HZM 8/ resp. 9/0 NEW! page Transverse pull page 8 Q Generall the open C channels determine the values. Perm. transverse loads depend on the construction. See also transverse load on welded channels on p. 8. Notes, Working Help Pipe Clamps, Pipe Supports Cantilever Arms for mild steel channels Halfen T-head bolts, Material:, HS tpicall grade. or grade of each bolt: See tpe selection on p. 9 - for stainless steel channels Stainless steel grades A - 0/ 0, A - 0/ 0 or grade of each bolt: See tpe selection on p. 9 - grade 8.8 Stainless steel Halfen T-head bolts, Material: A, A HS HS HS HSR Thread M M 8 M 0 M M M 0 M M M 0 Thread M M 8 M 0 M M M 0 M M M 0 Ma. pull out per T-head bolt grade.,,0, 9,,,0 8,8 0,, Ma. pull out per T-head bolt A - 0 A - 0,,0, 9,,,0 8,8 0,, S Ma. longitudinal load per Halfen T-head bolt S Tpe HS, grade. Tpe HS, grade 8.8 Tpe HSR, grade 8.8 grade at tightening at tightening at tightening 8.8 torque torque ( = ) torque [Nm] [Nm] [Nm], 0, 0, 0 8, 0, 8 0,, 0,, 8 9, 0,, 0, 0,9 0,0 00,0 00,, 0, 00, 00 8,,0 00,8 80 0,0, 00 8, ,0, 00 A - 0 A - 0,0, 8,,,,8 Ma. longitudinal load per Halfen T-head bolt A - 0/0 A - 0/0 0, 0, 0, 0, 0,9,,0 at tightening torque [Nm] Hafen T-head bolt with nibs. Permitted load as per official report MPA Baden- Württemberg from 0..98,,0. Calculated load capacit with safet coefficient,0. or constructions loaded in longitudinal direction, Halfen T-head bolts with nibs, Tpe HSR (p. 9 -, ; not in Stainless steel), are to be used. 0

61 HAEN RAMING SYSTEMS Sstem Series for Medium oading HAEN ocking plates and T-head bolts Sstem Series - load capacities Pull out loads S Generall the ma. loads of HAEN s are lower than those of T-head bolts ( pages - 9). ongitudinal loads In mild steel channels, the permissible load in longitudinal direction is higher than in stainless steel channels - due to the increased grip of flame-hardened locking-plate-teeth into the channel lips. or stainless steel, we recommend toothed channels. Important: Do not eceed tightening torque of T-head bolt. Transverse pull page 8 Q Generall the open C channels determine the values. Perm. transverse loads depend on the construction. See also transverse load on welded channels on p. 8. Availabilit for mild steel channels Material:, d d, b,, b = Standard = to order, 0, ocking plates 0 d,, for stainless steel channels Material: Stainless steel A Thread GWP / Thread M M 8 M 0 M M M GWP / -SH, -SN GWP / GWP / b HZS / T-head bolts HZS /,, HZS / = plain form, fits to all s Series M M 8 M 0 M M HZS / Dim. d/ b / 0 8/ 0 9/ 0 / 0 9/ 0 / 0 HZS / Ma. pull out per T-head bolt S for all s Series Do not eceed channel load capacit.,0,0,0 9,0,0,0 - see below Ma. pull out per T-head bolt Do not fit to s / Insert GWP /-M (b = 0mm) from channel end. HZS /-M = forged, without toothing, ma. longitudinal load: kn for s HM/H /, / /, /8,0,,,0,0, Ma. longitudinal load per Halfen T-head bolt for toothed s HZM/HZ /,/,,0,0,0,0, Ma. longitudinal load per Halfen T-head bolt at tightening torque [Nm] 8 0 (0) (80) GWP GWP S / / for s for toothed s ocking plates T-head bolts Dim. Do not eceed HM/H at tightening HZM/HZ GWP GWP HZS d/ b channel load capacit. /, / torque /, / / / / [Nm] / 0,0 0,,, 8/ 0,0 0,,0,0 9/ 0,0,,,0 9/ 0,0,,0 (0),0 / 0,0,0,0 (80),0 at tightening torque [Nm],,0,,0 (0),0 (80) Values in brackets for Tpes GWP / and HZS / Ma. load in longitudinal direction does not appl to T-head bolts HS / and locking plates GWP /

62 HAEN RAMING SYSTEMS HAEN POWERCICK raming Sstem Never has so little given so much: THREE SIZES - one sstem POWERCICK SYSTEM Suitable for pipes with nominal diameters up to 0 mm or 00 mm on agreed applications kg Catalogues PC and PC -P POWERCICK SYSTEM Suitable for pipes with nominal diameters up to 80 mm or 0 mm with short spans or agreed applications kg Catalogue PC POWERCICK SYSTEM Suitable for pipes with nominal diameters up to mm Catalogue PC POWERCICK ACCESSORIES Cantilevers, pipe clamps, sliding supports Catalogue PC Z kg kg kg kg kg

63 HAEN RAMING SYSTEMS HAEN POWERCICK raming Sstem for Heav Dut HZ / toothed Application eamples of Support structures HAEN POWERCICK raming Sstem kg kg Bolt set Powerclick pre-assembled in all fittings Also suitable: locking plates and T-head bolts of Sstem page GWP / GWP /SN HZS / Base channel: HZ / kn Slotting: 8 distance 0 mm HZ / or further informations see Technical Information PC HAEN POWERCICK 9,, 9, Bolt set Powerclick or locking plate GWP / plus Heagon head bolt M kg data: Bending capacit at span [m] 0,0,00,0, 8,, kg kg page 9 kg Ma. load compression member Thrd. M Other channel data, design properties pages - 9 kg S kg Ma. longitudinal load per T-head bolt:, ocking plate GWP / at tightening torque 0 Nm at tightening torque,0 0 Nm

64 HAEN RAMING SYSTEMS HAEN Sstem Series for Heav Dut, Overview HAEN ittings Sstem Series Angle fittings, fiing plate, screw connection tie etc. pcs. HVT - 8 combined to binder HVT - 8 Components to assembl, Sstem Series Eamples HM / Beam with angle fittings HVT - HM / rame constructions: will be manufactured to our measurements HM /D HVT /8 Assembl channel rings: Manufacturing of channel rings and lateral channel slotting also to our measurements Articulated brace Deliver times on request. Base channel for channel rings and support structures: HM / HM / Back-to-back channel HM / D on request Tpe HSR Articulated beam ring, HSR 0/ M 0 (h.d. galvanised) HS 0/0 - A-0 - M 0 (Stainless steel A) Beam with shoe fittings, increased load capacit data: Bending capacit at span [m] Ma. load compression member Articulated cantilever HVT / Eternal radius as measure specification Ma. longitudinal load per T-head bolt Tpe HS, grade A-0 Tpe HSR, grade 8.8 resp. grade. 0,0,00,0 at tightening at tightening Thrd. torque torque 8,,, page 9 load capacities back-to-back channels M,0 00 Nm 0,9 0 Nm,, 9,0 page 9 Other channel data pages - ; design properties pages 8-9 slot inside

65 HAEN RAMING SYSTEMS HAEN ittings Sstem Series HM / hot rolled All T-head bolts and locking plates of Tpe 0/0 are suitable. HVT - ittings Sstem Series, fit to /, hole-ø 8 mm 90 HVT HVT HVT - - HVT HVT - - HSR 0/0 M, M0 with nibs HVT HVT - - HVT -8 combined to binder HVT HVT HS 0/0 M0-M0 GWP 0/0 M8-M Curved channels and channel rings on request Unless otherwise stated, the following dimesions appl for all fittings. R Ø Application eamples: All part sketches show onl one of man possible applications. Designation V = hot dip galvanised HVT---V HVT---V HVT---V HVT---V HVT---V HVT---V HVT---V HVT--8-V HVT--9-V Stock no Designation Stock no A = Stainless steel W./.0 HVT---A 000 HVT---A 000 HVT---A 000 HVT---A 000 HVT---A 000 HVT---A 000 HVT---A 000 HVT--8-A 0008 HVT--9-A 0009 to order

66 HAEN RAMING SYSTEMS Sstems and Series, Standard Sstems for Medium Dut, Overview HAEN POWERCICK is a standard support sstem for pipe assembl. All fittings are pre-converted with HA- EN T-head bolts. Using POWERCICK, assembl times are reduced about 0%, and because of free sstem adjustment costl workarounds become redundant. The efficient dimensioning of POWER- CICK Sstem assures the same strength like conventional constructions, but is more fleible. HAEN POWERCICK copes with ever situation with standard sstem solutions.. The catalogue HAEN POWERCICK raming Sstem Series offers further information. With clearl arranged data it is an important planning aid for users. Ever accessor part is introduced separatel with all technical data. Above all, the HAEN Planning Service will support our project. POWERCICK makes it eas. or all applications onl a few different com- ponents, for all channels onl one and the same HAEN T-head bolt is necessar. The bolt is pre-assembled within the fittings, is to be fied in no time at all and is partiall load bearing even before tightening. Because of the eas weight of the components no lifting devices are required. Due to the fleible adjusting site tolerances can be easili compensated. HAEN POWERCICK raming Sstem Series Components, read to assembl, for medium dut HAEN POWERCICK raming Sstem Series kg pages 8-9 HAEN Ring Sstem Series