SST Tag: Message: (32 characters)

Transcription

1 , Rev AA June 213 ROSEMOUNT 395FB Information Customer: Rosemount 395 MultiVariable Configuration Data Sheet Contact Name: Customer Phone: Customer Approval Sign-Off: Model No (1) Customer Fax: Customer PO: SST Tag: Transmitter Information (optional) Software Tag: (8 characters) Descriptor: Message: (16 characters) (32 characters) Date: Day (numeric) Month (numeric) Year (numeric) Transmitter Information Transmitter Address (Range 1 247) Baud Rate (Select one) Process Temperature Setup Temperature mode options: Normal - The transmitter will report the measured RTD temperature value. Fixed/Backup - The transmitter reports the Fixed/Backup temperature value if the RTD fails or in the absence of an RTD measurement Enter a value to be used for Backup (RTD Failure) or Fixed (No RTD): Fixed/Backup Temperature (Units are selected in the Outputs section below) Outputs Units: Differential Pressure: inh 2 6 F (Inches of 6 F) PA (Pascals) kpa (Kilopascals) inh 2 68 F Static Pressure: PSI (Pounds per square inch) kpa (Kilopascals) MPa (Megapascals) Process Temperature: Fahrenheit Celsius Trim Value Lower (LTV) Upper (UTV) Default Values Differential Pressure: LRL, URL Static Pressure: atmosphere, URL (absolute) Process Temperature:, URL (gage), LRL, URL

2 Rosemount 395 MultiVariable Configuration Data Sheet , Rev AA June 213 Operation Limit Lower Upper Default Values Differential Pressure:, URL Static Pressure:, URL Process Temperature: LRL, URL Lower and upper operating limits must be within the minimum and maximum range limits as stated in the Range Limits Table (see page 3). (1) A complete model number is required before Rosemount Inc. can process the order. Damping (in seconds) Differential Pressure: (select one) Static Pressure: (select one) Process Temperature: (select one) S.O.: CHAMP: For Rosemount Use Only LI DATE: ADMIN: Units inh 2 O psi Pa kpa MPa 395FB MultiVariable Transmitter Range Limits Range 2 DP Span Range 3 DP Span Range 3 (AP) Range C (GP) Span Range 4 (AP) Range D (GP) Span min. max min. max min. max min. max

3 , Rev AA June 213 Rosemount 395 MultiVariable ROSEMOUNT 395FC Information Customer: Customer Phone: Customer Approval Sign-Off: Contact Name: Customer Fax: Customer PO: Model No (1) Tag Information (optional) Wired Tag: (5 lines of 17 characters) Permanent (3 lines of 25 characters): Meter I.D. (1 characters) Meter Description (3 characters) Transmitter Information Engineering Units U.S. Metric Differential Pressure: inh 2 O at 6 F kpa Static Pressure: psi kpa Process Temperature: Fahrenheit Celsius Flow Foot 3 / hour Meter 3 / hour Station Name (2 characters) (395FC ) Meter Address 1 (1 255) Group 2 (1 255) Baud Rate (6, 12, 24, 48, 96, 19.2K) (1) A complete model number is required before Rosemount Inc. can process the order. 3

4 Rosemount 395 MultiVariable Configuration Data Sheet , Rev AA June 213 Meter Setup Pipe ID: ( in / mm) at reference temperature ( F / C) Pipe Material: Carbon Steel SST Monel Orifice Plate ID: ( in / mm) at reference temperature F / C) Orifice Material: Carbon Steel SST Monel Low Flow Cutoff: ( inh 2 O / kpa) Averaging Technique: Flow Dependent Linear Flow Weighted Linear Flow Dependent Formulaic Flow Weighted Formulaic Choose desired characterization method and only enter values for that method. Detail Characterization Method (AGA8 1992) Default Value N 2 CO 2 C1 C2 C3 nc4 ic4 nc5 ic5 C6 C7 C8 C9 C1 H 2 S H 2 O He O 2 CO H 2 Nitrogen mole percent Carbon Dioxide mole percent Methane mole percent Ethane mole percent Propane mole percent n-butane mole percent i-butane mole percent n-pentane mole percent i-pentane mole percent Hexane Heptane Octane Nonane Decane Hydrogen Sulfide mole percent Water mole percent Helium Oxygen mole percent Carbon monoxide mole percent Hydrogen mole percent Gross Characterization Method, Option Code 1 (AGA8 Gr-Hv-CO 2 ) Specific Gravity Heating Value Units Basis CO 2 Mole % H 2 Mole % CO Mole % BTU/Lb Dry Gross Characterization Method, Option Code 2 (AGA8 Gr-CO 2 -N 2 ) Specific Gravity Heating Value Units Basis N 2 Mole % CO 2 Mole % H 2 Mole % CO Mole % BTU/Lb Dry BTU/CF Wet BTU/CF Wet 4

5 , Rev AA June 213 Rosemount 395 MultiVariable Pressure Tap Gauge Absolute Upstream Downstream Base Conditions Base Pressure: (14.73 psi / kpa) Base Temperature: (6 F / C) Elevation: (5 feet / meters) Latitude: (35 degrees ) Viscosity: (.1268 Cp ) Sp Heat Ratio: (1.3 ) Atmospheric Pressure Calculate based on entered parameters Enter (14.45 psi / kpa) Flow Alarms Disable Enable Low Alarm (MCF/day / km 3 /day) High Alarm (MCF/day / km 3 /day) PV Fault Values DP: Last Good Value User-Specified Fault Value SP: Last Good Value User-Specified Fault Value T: Last Good Value User-Specified Fault Value History Contract Hour: ( 23 integer) ( = midnight ) Logged Parameters (Select any number of variables. Selected parameters apply to both daily logs and variable logs.) Total Flow Minimum Static Pressure Other: Total Flow Time Average Process Temperature Other: Total Energy Average Heating Value Other: Average Flow Rate Average Compressibility Factor Other: Average Energy Rate Average Integral Value Other: Average Differential Pressure Average C Prime or Integral Multiplier Value (IMV) Other: Maximum Differential Pressure Specific Gravity (Relative Density) Other: Minimum Differential Pressure Maximum Process Temperature Other: Average Static Pressure Minimum Process Temperature Other: Maximum Static Pressure Uncorrected Flow Rate 5

6 , Rev AA June 213 LCD Display Information (Only enter if LCD meter ordered.) Display Parameters (Select any number of variables.) Flow Rate Totalized Energy Yesterday Other: Differential Pressure Mole Percent CO 2 Other: Totalized Flow Today Mole Percent N 2 Other: Totalized Flow Yesterday Orifice Bore at 68 F Other: Static Pressure Date and Time Other: Temperature Heating Value Other: Energy Flow Rate Specific Gravity (Relative Density) Other: Totalized Energy Today Special Calibration (Optional) Default values indicate standard calibration. Enter lower trim and upper trim values if special calibration is desired: Trim Value Lower (LTV) Upper (UTV) Default Values Differential Pressure:, URL Static Pressure:, URL Process Temperature (fixed): F S.O.: CHAMP: For Rosemount Use Only LI DATE: ADMIN: 395FC Flow Transmitter Range Units Differential Pressure Range 2 Span Absolute Pressure Range 3 Span Absolute Pressure Range 4 Span Units min max Units min max min max in H 2 O psia kpa MPa in H 2 O (1) 1 1 kpa (1) (1) Range 3. Standard Terms and Conditions of Sale can be found at The Emerson logo is a trade mark and service mark of Emerson Electric Co. Rosemount, Annubar, ProPlate, and the Rosemount logotype are registered trademarks of Rosemount Inc. Engineering Assistant is a registered trademark of AMS Suite. Emerson Process Management Rosemount Measurement 82 Market Boulevard Chanhassen MN USA Tel (USA) Tel (International) Fax Emerson Process Management Rosemount Measurement 13 Concord Terrace, Suite 4 Sunrise Florida USA Tel Rev AA, 6/13 Emerson Process Management Blegistrasse 23 P.O. Box 146 CH 6341 Baar Switzerland Tel +41 () Fax +41 () Emerson FZE P.O. Box 1733 Jebel Ali Free Zone Dubai UAE Tel Fax Emerson Process Management Asia Pacific Pte Ltd 1 Pandan Crescent Singapore Tel Fax Service Support Hot line: Enquiries@AP.EmersonProcess.com