APPLICATION FOR TEST REPORT. On Behalf of. : Global Tech China Limited. LED Flood Light. Model: X with PIR, 40300XX without PIR

Transcription

1 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS ALICATIO FOR TEST REORT On Behalf of Global Tech China Limited LED Flood Light Model: X with IR, 40300XX without IR repared For : Global Tech China Limited 3 Flat A, Wai Yip Industrial Building, 171 Wai Yip Street, Kwun Tong, Kowloon, Hong Kong repared By : Shenzhen LCS Compliance Testing Laboratory Ltd. 1F., Xingyuan Industrial ark, Tongda Road, Bao an Blvd., Bao an District, Shenzhen, Guangdong, China Date of Test : May 06, 2013 May 17, 2013 Date of Report : May 17, 2013 Report umber : LCS TS

2 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS TEST REORT E Luminaires art 2: articular requirements Section Five Floodlights Report reference o...: LCS TS Tested by(name + signature)...: Olivia Yang Approved by(name + signature)...: Hart Qiu Date of issue...: May 17, 2013 Contents...: 52 pages Testing laboratory ame... : Shenzhen LCS Compliance Testing Laboratory Ltd. Address... : 1F., Xingyuan Industrial ark, Tongda Road, Bao an Blvd., Bao an District, Shenzhen, Guangdong, China Testing location...: As above Client ame...: Global Tech China Limited Address...: 3 Flat A, Wai Yip Industrial Building,171 Wai Yip Street, Kwun Tong, Kowloon, Hong Kong Manufacturer ame...: Global Tech China Limited Address...: 3 Flat A, Wai Yip Industrial Building,171 Wai Yip Street, Kwun Tong, Kowloon, Hong Kong Test specification Standard...: E : 1998; E : 2008+A11: 2009; E 62031: 2008; E 62493: 2010 Test procedure...: Compliance with E : 1998; E : 2008+A11: 2009; E 62031: 2008; E 62493: 2010 on-standard test method...:.a. Test item Description...: LED Flood Light Trade Mark...: Mighty Lite Model and/or type reference...: X with IR, 40300XX without IR Rating(s)...: Input: 230V~, 50Hz, 0.63mA, ower consumption: 15W age 1 of 52

3 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS Test item particulars Classification of installation and use.: Supply Connection.. : Class II Terminal block Test case verdicts Test case does not apply to the test object : Test item does meet the requirement...: Test item does not meet the requirement...: (/A) (ass) F(Fail) Testing Date of receipt of test item...: May 06, 2013 Date(s) of performance of test...: May 06, 2013 May 17, 2013 General remarks This report shall not be reproduced except in full without the written approval of the testing laboratory. The test results presented in this report relate only to the item tested. Clause numbers between brackets refer to clauses in IEC (E ). "(see remark #)" refers to a remark appended to the report. "(see Annex #)" refers to an annex appended to the report. Throughout this report a comma is used as the decimal separator. Remark 1. Rubbing for 15 s with a piece of cloth soaked with water. And a further 15 s with a piece of cloth soaked with petroleum. 2. All models are similar except their power and appearance. All tests were conducted on model X with IR. 3. The report includes Attachment o. 1: Report of E Attachment o. 2: Report of E Attachment 3: 4 pages of product photos. age 2 of 52

4 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS Copy of marking plate Mighty Lite LED Flood light Model: X with IR Input: 230V~, 50Hz ower consumption: 15W Global Tech China Limited MADE I CHIA age 3 of 52

5 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS E (0) General test requirements 5.2 (0.1) Information for luminaires design considered Yes [ ] o [ ] 5.2 (0.3) More sections applicable 230V 5.4 (2) CLASSIFICATIO 5.4 (2.2) Type of protection...: Class II 5.4 (2.3) Degree of protection...: I (2.4) Luminaire suitable for direct mounting on normally flammable surfaces...: Luminaire not suitable for direct mounting on normally flammable surfaces....: Fixed luminaire 5.4 (2.5) Luminaire for normal use...: Yes o Luminaire for rough service...: o 5.5 (3) MARKIG 5.5 (3.2) Markings on luminaires See marking label osition of the marking Bottom of the product Format of symbols/text The height of symbols more than 5mm, text more than 2mm 5.5 (-) Additional information Language of instructions In English a) Operating position, if not universal. b) Weight and overall dimensions of the floodlight. c) Maximum projected area of the floodlight. d) Range of mounting heights. e) Suitability for use indoors. Indoor or outdoor 5.5 (3.3.1) Combination luminaires ot combination luminaire 5.5 (3.3.2) ominal frequency in Hz 50Hz 5.5 (3.3.3) Operating temperature Ambient temperature: (3.3.4) Symbol or warning notice 5.5 (3.3.5) Wiring diagram 5.5 (3.3.6) Special conditions o such special conditions 5.5 (3.3.7) Metal halid lamp luminaire warning 5.5 (3.3.8) Limitation for semi-luminaires age 4 of 52

6 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS E (3.3.9) ower factor and supply current ower factor : 0.919, supply current : 0.63A 5.5 (3.3.10) Suitability for use indoors Use outdoor or indoor 5.5 (3.3.11) Luminaires with remote control ot such construction 5.5 (3.3.12) Clip-mounted luminaire - warning 5.5 (3.3.13) Specifications of protective shields 5.5 (3.3.14) Symbol for nature of supply ~ 5.5 (3.3.15) Rated current of socket outlet o socket outlet 5.5 (3.3.16) Rough service luminaire ormal service luminaire 5.5 (3.3.17) Mounting instruction for type Y, Type Z and some type X attachments 5.5 (3.3.18) on-ordinary luminaires with VC cable 5.5 (3.3.19) rotective conductor current in instruction if applicable 5.5 (3.3.20) rovided with information if not intended to be mounted within arms reach 5.5 (3.4) Test with water 15s Test with hexane 15s Legible after test Still legible. Label attached Still attached. 5.6 (4) COSTRUCTIO 5.6 (4.2) Components replaceable without difficulty All components can not be replaced 5.6 (4.3) Wireways smooth and free from sharp edges 5.6 (4.4) Lamp holders o lamp holder 5.6 (4.4.1) Integral lamp holder 5.6 (4.4.2) Wiring connection 5.6 (4.4.3) Lamp holder for end-to-end mounting 5.6 (4.4.4) ositioning - pressure test ()..: After test the lamp holder comply with relevant standard sheets and show no damage age 5 of 52

7 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS E After test on singal-capped lampholder the lampholder have not moved form its position and show no permanent deformation - bending test () : After test the lamholder have not moved from its position and show no permanent deformation 5.6 (4.4.5) eak pulse voltage o ignitors 5.6 (4.4.6) Centre contact o ignitors 5.6 (4.4.7) arts in rough service luminaires resistant to tracking ot for rough service 5.6 (4.4.8) Lamp connectors o lamp connector 5.6 (4.4.9) Caps and bases correctly used 5.6 (4.5) Starter holders o starter holders Starter holder in luminaries other than Class II Starter holder Class II construction 5.6 (4.6) Terminal blocks Tails Unsecured blocks 5.6 (4.7) Terminals and supply connections 5.6 (4.7.1) Contact to metal parts 5.6 (4.7.2) Location stranded wires 8 mm test live conductor 8 mm test earth conductor 5.6 (4.7.3) Terminals for supply conductors 5.6 ( ) Welded connections - stranded or solider conductor - spot welding - welding between wires - type Z attachment - mechanical test according to electrical test according to hest test according to and (4.7.4) Terminals other than supply connection age 6 of 52

8 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS E (4.7.5) Heat-resistant wiring/sleeves 5.6 (4.7.6) Multi-pole plug - test at (4.8) Switches: o switches - adequate rating - adequate fixing - polarized supply - Compliance with for electronic switches 5.6 (4.9) Insulating lining and sleeves 5.6 (4.9.1) Retainment Method of fixing : Insulation sleeves 5.6 (4.9.2) Insulated linings and sleeves Resistant to temperature >20 to the wire temperature or a) & c) Insulation resistance and electric strength Comply with requirements b) Ageing test. Temperature ( )...: 5.6 (4.10) Insulation of Class II luminaires Class II appliance 5.6 (4.10.1) o contact, mounting surface - accessible metal parts - wiring of basic insulation Safe installation fixed luminaires Capacitors and switches lastic shell Interference suppression capacitors according to IEC (4.10.2) Assembly gaps: - not coincidental - no straight access with test probe 5.6 (4.10.3) Retainment of insulation: - fixed - unable to be replaced; luminaire inoperative - sleeves retained in position - lining in lamp holder 5.6 (4.11) Electrical connections 5.6 (4.11.1) Contact pressure o pressure transmitted to the insulating material 5.6 (4.11.2) Screws: - Self-tapping screws - thread-cutting screws age 7 of 52

9 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS E (4.11.3) Screw locking: - spring washer - rivets o rivet provided 5.6 (4.11.4) Material of current-carrying parts > 50% copper 5.6 (4.11.5) o contact to wood or mounting surface o wood 5.6 (4.11.6) Electro-mechanical contact systems o such construction 5.6 (4.12) Mechanical connections and glands 5.6 (4.12.1) Screw not made of soft metal Screws of insulating material Torque test: torque (m); part Torque test: torque (m); part Torque test: torque (m); part 5.6 (4.12.2) Screw with diameter < 3 mm screw into metal Fixed enclosure; 3.85mm, 1.2m 5.6 (4.12.4) Locked connections: - fixed arms; torque (m)...: - lampholder; torque (m)...: - push-button switches; torque (m)...: o such switches 5.6 (4.12.5) Screwed glands; force ()...: 5.6 (4.13) Mechanical strength 5.6 (4.13.1) Impact tests: - fragile parts; energy (m)...: 0.5m for glasses enclosure - other parts; energy (m)...: 0.7m for metal enclosure 1) live parts Inaccessible 2) linings o linings provided 3) protection 4) covers o such covers 5.6 (4.13.2) Metal parts enclosing live parts shall have adequate mechanical strength 5.6 (4.13.3) Straight test finger (4.13.4) Rough service luminaires ormal service luminaires I 54 or higher a) fixed b) hand-held age 8 of 52

10 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS E c) delivered with a stand d) for temporary installations and suitable for mounting on a stand 5.6 (4.13.6) Tumbling barrel 5.6 (4.14) Suspensions and adjusting devices 5.6 (4.14.1) Mechanical load: A) four times the weight B) torque 2.5 m C) bracket arm; force ()...: D) load track-mounted luminaires E) clip-mounted luminaires, glass-shelve; thickness (mm)...: metal rod; diameter (mm)...: 5.6 (4.14.2) Load to flexible cables: mass (kg)...: stress in conductors (/mm²)...: Mass (kg) of semi-luminaires...: Bending moment (m) of semi-luminaires : 5.6 (4.14.3) Adjusting devices: - flexing test; number of cycles...: - strands broken - electric strength test afterwards 5.6 (4.14.4) Telescopic tubes: cords not fixed to tube; no strain on conductors o such tubes 5.6 (4.14.5) Guide pulleys o such construction 5.6 (4.14.6) Strain on socket-outlets ot such unit 5.6 (4.15) Flammable materials: - glow-wire test spacing 30 mm - screen withstanding test of screen dimensions - no fiercely burning material - thermal protection - electronic circuits exempted 5.6 (4.15.2) Luminaires made of thermoplastic material age 9 of 52

11 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS E a) construction b) temperature sensing control c) surface temperature 5.6 (4.16) Luminaires for mounting on normally flammable surfaces o lamp control gear 5.6 (4.16.1) Lamp control gear shall spacing: - spacing 10 mm - spacing 35 mm 5.6 (4.16.2) Thermal protection: - in lamp control gear - external Internal - fixed position - temperature marked lamp control gear 5.6 (4.16.3) Design to satisfy the test of (4.17) Drain holes o drain holes Clearance at least 5 mm 5.6 (4.18) Resistance to corrosion: 5.6 (4.18.1) - rust-resistance ainted with rust-resistance material 5.6 (4.18.2) - season cracking in copper 5.6 (4.18.3) - corrosion of aluminium o aluminium used 5.6 (4.19) Ignitors compatible with ballast o ignitors used 5.6 (4.20) Rough service vibration...: ot such appliance 5.6 (4.21) rotective shield 5.6 (4.21.1) Shield fitted Shield of glass if tungsten halogen lamps 5.6 (4.21.2) articles from a shattering lamp not impair safety 5.6 (4.21.3) o direct path 5.6 (4.21.4) Impact test on shield Glow-wire test on lamp compartment 5.6 (4.22) Attachments to lamps o such attachments 5.6 (4.23) Semi-luminaires comply with Class II ot such appliance 5.6 (4.24) UV radiation for tungsten halogen lamps and metal halide lamps (Annex ) o such appliance age 10 of 52

12 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS E (4.25) o sharp point edges o sharp points or edges 5.6 (4.26) Short-circuit protection 5.6 (4.26.1) Uninsulated accessible SELV parts 5.6 (4.26.2) Short circuit test 5.6 (4.26.3) Test chain according to figure (-) Floodlights for use outdoors shall have protection against the ingress of moisture at least equivalent to IX (-) Lampholder brackets and lamp supports where used shall withstand normal usage throughout the life of the floodlight. They shall accept and retain lamps which are within the dimensional tolerances stated in the appropriate IEC publication where applicable, and locate the lamp or lamps in the designed relationship to the optical control devices in the floodlight (-) When provision is made for alternative sizes of lamps or light centre positions, the adjusting means shall be positive and firmly retained in the selected position (-) Refractors, reflectors or any other light controlling components shall be so marked or constructed that they can be fitted or replaced only in the correct relationship to the light source (-) The means for attaching the floodlight to its support shall be appropriate to the weight of the floodlight. For floodlights for use above ground level outdoors, the connection shall withstand wind speeds of 150 km/h on the projected surface of the floodlight assembly without undue deflection. arts of floodlights for mounting heights 3 m or higher which are fixed other than with at least two devices, 5.6.6(-) Where means for angular adjustment are provided, there shall be provision for positive locking after any such adjustments have been effected (-) Floodlights for use outdoors shall be resistant to the vibrations which may occur during normal use (-) Glass covers shall either consist of a glass that fractures into small pieces, or shall be provided with a guard of sufficiently small mesh or the use of a film-coated glass that retains glass fragments. I64 <3m age 11 of 52

13 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS E (11) CREEAGE DISTACES AD CLEARACES Working voltage (V)...: 230V~ Voltage form Sinusoidal [ ] on-sinusoidal [ ] TI < 600 [ ] > 600 [ ] Impusle withstand category (normal category II) (category III annex U) Category II Rated pulse voltage (kv)...: <2.0kV (1) Current-carrying parts of different polarity: cr (mm); cl (mm)...: (2) Current-carrying parts and accessible parts: cr (mm); cl (mm)...: (3) arts becoming live due to breakdown of basic insulation and metal parts: cr (mm); cl (mm)...: (4) Outer surface of cable where it is clamp and metal parts: cr (mm); cl (mm)...: (5)not used (6) Current-carrying parts and supporting surface: cr (mm); cl (mm)...: cl>3.5mm, limit: 1.5mm cr>3.5mm, limit: 2.5mm cl>7.5mm, limit: 3.0mm cr>7.5mm, limit: 5.0mm cl>7.5mm, limit: 3.0mm cr>7.5mm, limit: 5.0mm 5.8 (7) ROVISIO FOR EARTHIG 5.8 ( ) Accessible Metal parts metal parts in contact with supporting surface Resistance < 0.5Ω Self-tapping screws used Thread-forming screws Thread-forming screws used in a grove Earth markes contact first 5.8 ( ) Earth continuity in joints etc. 5.8 (7.2.4) Locking of clamping means Compliance with Terminal blocks with integrated screwless earthing contacts tested according Annex V 5.8 (7.2.5) Earth terminal integral part of Connector age 12 of 52

14 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS E socket 5.8 (7.2.6) Earth terminal adjacent to mains terminals 5.8 (7.2.7) Electrolytic Corrosion of the earth terminal Ordinary luminaire. 5.8 (7.2.8) Material of earth terminal Contact surface bare metal 5.8 (7.2.10) Class II luminaire for looping-in Double or reinforced insulation to functional earth 5.8 (7.2.11) Earthing core coloured green-yellow Length of earth conductor 5.9 (14) SCREW TERMIALS Separately approved: component list See annex 1 art of the luminaire See annex (15) SCREWLESS TERMIALS -- Separately approved: component list See annex 1 art of the luminaire See annex (5) EXTERAL AD ITERAL WIRIG 5.10 (5.2) Supply connection and external wiring 5.10 (5.2.1) Means of connection...: Terminal block 5.10 (5.2.2) Type of cable...: ominal cross-section area (mm 2 ) Cables equal to IEC and IEC (5.2.3) Type of attachment, X,Y or Z 5.10 (5.2.5) Type Z not connected to screws 5.10 (5.2.6) Cable entries - suitable for introduction - adequate degree of protection 5.10 (5.2.7) Cable entries through rigid material have rounded edges 5.10 (5.2.8) Insulating bushings: - suitably fixed - material in bushings age 13 of 52

15 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS E material not likely to deteriorate - tubes or guard made of insulating material 5.10 (5.2.9) Locking of screw bushings 5.10 (5.2.10) Cord anchorage: - covering protected from abrasion - clear how to be effective - no mechanical or thermal stress - no tying of cables into knots etc. - insulating material or lining 5.10 ( ) Cord anchorage for type X attachment cord a) at least one part fixed b) types of cable c) no damaging of the cable d) whole cable can be mounted e) no touching of clamping screws f) metal screw not directly on cable g) replacement without special tool Glands not used as anchorage Labyrinth type anchorage 5.10 ( ) Adequate cord anchorages for type Y and type Z attachments 5.10 ( ) Tests: - impossible to push cable; unsafe - pull test: 25 times; pull () - torque test: torque (m) - displacement 2 mm - no movement of conductors - no damage of cable or cord 5.10 (5.2.11) External wiring passing into luminaire 5.10 (5.2.12) Looping-in terminals ot looping-in appliance 5.10 (5.2.13) Wire ends not tinned Wire ends tinned: no cold flow 5.10 (5.2.14) Mains plug same protection Class III luminaire plug age 14 of 52

16 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS E (5.2.16) Appliance inlets (IEC 60320) o appliance inlet Appliance couplers of class II type 5.10 (5.2.17) o standardized in interconnecting cables assembled 5.10 (5.2.18) Used plug in accordance with - IEC other standard 5.10 (5.3) Internal wiring 5.10 (5.3.1) Internal wiring of suitable size and type Through wiring - not delivered/ mounting instruction - factory assembled - socket outlet loaded (A)...: - temperatures...: Green-yellow for earth only 5.10 ( ) Internal wiring connected directly to fixed wiring Cross-Sectional area (mm 2 ) 24AWG Insulation thickness >0.6mm Extra insulation added where necessary 5.10 ( ) Internal wiring connected to fixed wiring via internal current-limited device Adequate cross-section area and insulation thickness 5.10 ( ) Double or reinforced insulation for class II Class II appliance ( ) Conductors without insulation 5.10 ( ) SELV current-carrying parts 5.10 ( ) Insulation thickness other than VC or rubber 5.10 (5.3.2) Sharp edges etc. o moving parts of switches etc. Joints, raising/lowering devices Telescopic tubes etc. o twisting over (5.3.3) Insulating bushings - suitable fixed age 15 of 52

17 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS E material in bushings - material not likely to deteriorate - cables with protective sheath 5.10 (5.3.4) Joints and Junctions effectively insulated 5.10 (5.3.5) Strain on internal wiring 5.10 (5.3.6) Wire carriers 5.10 (5.3.7) Wire ends not tinned Wire ends tinned: no cold flow 5.11 (8) ROTECTIO AGAIST ELECTRIC SHOCK 5.11 (8.2.1) Live parts not accessible with standard test finger Basic insulated parts not used on the outer surface without appropriate protection Basic insulated parts not accessible with standard test finger on portable and adjustable luminaires Basic insulated parts not accessible with ø50mm probe from outside, within arms reach, on wall-mounted luminaires Lamp and startholders in portable and adjustable luminaires comply with double or reinforced insulation requirements Basic insulation only accessible under lamp or starter replacement Double-ended tungsten filament lamp Insulation lacquer not reliable Double-ended high pressure discharge lamp Relevant warming according to fitted to the luminaire 5.11 (8.2.2) ortable luminaire adjusted in most unfavourable position Fixed luminaire 5.11 (8.2.3 a) Class II luminaire: - basic insulated metal parts not accessible during starter or lamp replacement - basic insulated not accessible other than during starter or lamp replacement - glass protective shields not used as supplementary insulation age 16 of 52

18 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS E (8.2.3b) BC lampholder of metal in class I luminaires shall be earthed 5.11 (8.2.3c) Class III luminaires with expose SELV parts: Ordinary luminaire : - touch current - no-load voltage - other than ordinary luminaire: - nominal voltage 5.11 (8.2.4) ortable luminaire: - protection independent of supporting surface - terminal block completely covered 5.11 (8.2.5) Compliance with the standard test finger or relevant probe 5.11 (8.2.6) Covers reliably secured Cover not removable without tool 5.11 (8.2.7) Discharging of capacitors >0.5 μf ortable plug connected luminaire with capacitor Discharge device on or within capacitor Discharge device mounted separately 5.12 (12) EDURACE TEST AD THERMAL TEST 5.12 (12.3) Endurance test: - mounting-position...: In draught-proof enclosure - test temperature ( C)...: 35ºC - total duration (h)...: 240hrs. Totally 10 cycles, each 24h, the first 6 cycles in normal operation, the 7th cycle in abnormal operation. - supply voltage: Un factor; calculated voltage (V)...: 230VX1.1 - lamp used...: LED lamp 5.12 (12.3.2) After endurance test: - no part unserviceable - luminaire not unsafe - no damage to track system - marking legible age 17 of 52

19 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS E no cracks, deformation etc (12.4) Thermal test (normal operation) (see table 12.4 ) 5.12 (12.5) Thermal test (abnormal operation) Short-circuit of starter contacts Lamps removed and not replaced 5.12 (12.6) Thermal test (failed lamp control gear condition): 5.12 (12.6.1) Through wiring or looping-in wiring loaded by a current of (A) - case of abnormal conditions...: o electronic circuit - electronic ballast - measured winding temperature ( C): at 1.1 Un - measured mounting surface temperature ( C): at 1,1 Un...: - calculated mounting surface temperature( C) - track-mounted luminaires 5.12 (12.6.2) Temperature sensing control: - manual reset cut-out - auto reset cut-out - track-mounted luminaires 5.12 (12.7) Thermal test (failed ballast or transformer in plastic luminaires): 5.12 (12.7.1) Luminaire without temperature sensing control 5.12 ( ) Luminaire with fluorescent lamp 70W Test method or Annex V Test according to : - case of abnormal conditions - Ballast failure at supply voltage (V) - Components retained in place after the test - Test with standard test finger after the test Test according to Annex V: - case of abnormal conditions - measured winding temperature ( ): at 1.1 Un... : age 18 of 52

20 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS E measured temperature of fixing point/exposed part ( ): at 1.1Un... : - calculated temperature of fixing point/exposed part ( )...: Ball-pressure test: - part tested; temperature ( )... : - part tested; temperature ( )... : 5.12 ( ) Luminaire with discharge lamp, fluorescent lamp > 70W, transformer > 10 VA - case of abnormal conditions - measured winding temperature ( ): at 1.1 Un. : - measured temperature of fixing point/exposed part ( ): at 1.1 Un... : - calculated temperature of fixing point/exposed part ( ) : Ball-pressure test: - part tested; temperature ( )... : - part tested; temperature ( )... : 5.12 ( ) Luminaire with short circuit proof transformers 10 VA - case of abnormal conditions - Components retained in place after the test - Test with standard test finger after the test 5.12 (12.7.2) Luminaire with temperature sensing control - thermal link - manual reset cut-out - auto reset cut-out - case of abnormal conditions - highest measured temperature of fixing point/exposed part ( ):... : Ball-pressure test: - part tested; temperature ( )... : - part tested; temperature ( )... : When applying the limits in the tables 12-1 to 12-6 of section 12 of IEC to floodlights for use outdoors, 10 C shall be deducted from the temperatures measured age 19 of 52

21 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS E on the floodlight in the test enclosure to allow for the effects of natural air movement which occur in the working environment of the floodlight (9) RESISTACE TO DUST, SOLID OBJECTS AD MOISTURE 5.13 (9.2) Tests for ingress of dust, solid objects and moisture: - classification according to I...: I64 - mounting position during test...: - fixing screws tightened; torque (m)...: - tests according to clauses...: electric strength a) no deposit in dust-proof luminaire b) no talcum in dust-tight luminaire c) no trace of water on current-carrying parts or SELV parts or where it could become a hazard d) i) For luminaires without drain holes no water entry d) ii) For luminaires with drain holes no hazardous water entry e) no water in watertight luminaire f ) no contact with live parts (I 2X) f) no entry into enclosure (I 3X and I 4X) f) no contact with live parts (I3X and I4X) g) no trace of water on part of lamp requiring protection from splashing water h) no damage of protective shield or glass envelope 5.13 (9.3) Humidity test 48h Relative humidity 93%, temperature 25, 48h, followed by electric strength test 5.14 (10) ISULATIO RESISTACE AD ELECTRIC STREGTH 5.14 (10.2.1) Insulation resistance test: Cable or cord covered by metal foil or replaced by a metal rod of mm Ø... : Insulation resistance: SELV: - between current-carrying parts of different polarity... : Class II > 100MΩ, limit: 1MΩ age 20 of 52

22 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS E between current-carrying parts and mounting surface... : - between current-carrying parts and metal parts of the luminaire... : Other than SELV: > 100MΩ, limit: 1MΩ > 100MΩ, limit: 1MΩ - between live parts of different polarity...: > 100MΩ, limit: 2MΩ - between live parts and mounting surface: > 100MΩ, limit: 4MΩ - between live parts and metal parts... : > 100MΩ, limit: 4MΩ - between live parts of different polarity through action of a switch... : 5.14 (10.2.2) Electric strength test: Dummy lamp Luminaires with ignitors after 24 h test Luminaires with manual ignitors Test voltage (V): SELV: - between current-carrying parts of different 500Vac, 1min,no breakdown polarity... : - between current-carrying parts and mounting surface... : 500Vac, 1min,no breakdown - between current-carrying parts and metal parts of the luminaire... : 500Vac, 1min,no breakdown Other than SELV: - between live parts of different polarity... : 1460Vac, 1min,no breakdown - between live parts and mounting surface: 2920Vac, 1min,no breakdown - between live parts and metal parts... : 2920Vac, 1min,no breakdown 5.14 (10.3) Touch current (ma)...: 0.14mA<0.7mA 5.15 (13) RESISTACE TO HEAT, FIRE AD TRACKIG 5.15 (13.2.1) Ball-pressure test: - part tested; temperature ( C)...: CB, 125 C, 0.8mm - part tested; temperature ( C)...: Terminal block, 125 C, 0.6mm - part tested; temperature ( C)...: Bobbin of transformer, 125 C, 0.8mm 5.15 (13.3.1) eedle flame test (10 s): - part tested...: CB, Bobbin of transformer, Terminal block, no burnting - part tested...: 5.15 (13.3.2) Glow-wire test (650 C): age 21 of 52

23 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS E part tested...: CB, Bobbin of transformer, Terminal block, no burnting - part tested...: 5.15 (13.4.2) Tracking test: part tested...: 1.5 (3) MARKIG CEELEC COMMO MODIFICATIOS (E) ( ) Adequate warning on the package 1.10 (5) EXTERAL AD ITERAL WIRIG 1.10 (5.2.1) Connecting leads - without a means for connection to the supply - terminal block specified - relevant information provided - compliance with 4.6, 4.7.1, 4.7.2, , 11.2,12 and 13.2 of art (5.2.2) Cables equal to HD21 S2 or HD22 S2 ZB AEX ZB, SECIAL ATIOAL CODITIOS (E) (3.3) DK: power supply cord with label IT: warning label on Class 0 luminaire (4.5.1) DK: socket-outlets (5.2.1) CY, DK, FI, SE, GB: type of plug ZC AEX ZC, ATIOAL DEVIATIOS (E) (4&5) FR: Shuttered socket-outlets 10/16A (13.3) GB: Requirements according to United Kingdom Building Regulation (13.3.2) FR: Glow-wire test 850 alt. 750 for luminaires in premises open to public or 960 for luminaires in emergency exits -- age 22 of 52

24 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS Tables Object/part no. Internal wiring Transformer (T1) Bobbin Insulation Tape rimary Winding Secondary winding Insulating tube VARISH Fuse Resistor AEX 1: components Manufacturer/ trademark Dongguan Liuquan Electrical roducts Co Ltd ShenzhenHuaHong Xuan Electronics Co., Ltd Chang Chun lastics Co., Ltd. SuZou Mailaduona Electric Material Co., Ltd. Shantou Shengang Electrical Industrial Co., Ltd. Dah Jin Technology Co., Ltd. Chang Yuan Electronics (Shen Zhen)Co., Ltd. Wu Jiang Taihu Insulating Material Co Ltd Shenzhen Guohua Electronics Co., Ltd. Type/model Technical data Standard Mark(s) of conformity AWG, 200, 300V UL 758 UL DS-310-F Class B -- Test with appliance T375J V-0, 130 UL 94 UL E59481 JY312(#) Rating Thermal mm, 130 UL 510 UL E UEW/U 130 UL 1446 UL E TLW-B 130 UL 1446 UL E CB-TT-T/CB-TT- S 200V, 300 C UL 224 UL E T C UL 1446 UL E FR 5Ω, 1/2W -- Test with appliance Inductor I-Mag I-MAG mH E Test with appliance - Winding Tai-I Electric Wire & Cable Co Ltd - Bobbin Sumitomo Chemical Co., Ltd CB Terminal block Shenzhen Jove Enterprise Co Ltd Hongshang lastics Electron Co Ltd UEW 130 C UL 1446 UL E4012 V-0, 150 UL 94 UL JYE-S4(e) V-0, 130 C UL 95/UL 746C UL E CE 1 2.6mm, 300VAC,16A UL 486 UL 0.75mm 2 E age 23 of 52

25 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS Tables Y-capacitor X-capacitor RV1 Enclosure Shantou High- ew Technology Dev. Zone Songtian Enterprise Co., Ltd. Tenta Electric Industrial Co. Ltd. Dain Electronics Co., Ltd. Guangxi ew Future Information Industry Co., Ltd. Huizhou Wote Advanced Materials Co Ltd. CE Series Max pf, 250V~ E VDE MEX AC 275 V, 0.47uF E VDE MEX AC 275 V, 0.1uF E VDE D 130 C, 350V, 470pF IEC ; VDE IEC ; IEC C/ABS V-0, 90 UL 94 UL E Temperature( ) of part AEX 2: temperature measurements, thermal tests of Section 12 Type reference...: X with IR Lamp used.....: LED lamp Lamp control gear used......: -- Mounting position of luminaire......: Fixed mounted Supply wattage (W)...: 15W Supply current (A)..: 0.63A Calculated power factor..: Table: measured temperatures corrected for ta = 25 : - abnormal operating mode...: - test 1: rated voltage....: - test 2: 1.06 times rated voltage or 1,05 times Rated wattage : - test 3: Load on wiring to socket-outlet, 1.06 times voltage or 1.05 times wattage...: - test 4: 1,1 times rated voltage or 1,05 times rated wattage...: Through wiring or looping-in wiring loaded by current of A during the test...: V normal operation X230V -- Clause 12.4 normal Clause 12.5 abnormal Test 1 Test 2 Test 3 Limits( ) Test 4 Limit ( ) Internal wire Outside enclosure CB age 24 of 52

26 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS Tables Surface 1m distance from lamp Transformer winding Transformer bobbin Y-capacitors X-capacitor Ambient AEX 3: screw terminals (part of the luminaire) -- (14) SCREW TERMIALS -- (14.2) Type of terminal illar terminal Rated current (A) 16A ( ) One or more conductors Three conductors ( ) Special preparation ( ) Terminal size Cross-sectional area (mm²) (14.3.3) Conductor space (mm) 0.75mm 2 (14.4) Mechanical tests (14.4.1) Minimum distance (14.4.2) Cannot slip out (14.4.3) Special preparation (14.4.4) ominal diameter of thread (metric ISO thread) : External wiring o soft metal (14.4.5) Corrosion (14.4.6) ominal diameter of thread (mm) 0.75mm 2 Torque (m) (14.4.7) Between metal surfaces Lug terminal Mantle terminal ull test; pull () (14.4.8) Without undue damage AEX 4: screwless terminals -- (15) SCREWLESS TERMIALS -- (15.2) Type of terminal... : Rated current (A)... : (15.3.1) Material (15.3.2) Clamping (15.3.3) Stop age 25 of 52

27 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS Tables (15.3.4) Unprepared conductors (15.3.5) ressure on insulating material (15.3.6) Clear connection method (15.3.7) Clamping independently (15.3.8) Fixed in position ( ) Conductor size Type of conductor (15.5.1) Terminals internal wiring ( ) ull test spring-type terminals (4, 4 samples) ( ) ull test pin or tab terminals (4, 4 samples) Insertion force not exceeding 50 (15.5.2) ermanent connections: pull-off test (20 ) (15.6) Electrical tests -- Voltage drop (mv) after 1 h (4 samples)... : Voltage drop (mv) after 10th alt. 25th cycle (4 samples)... : Voltage drop (mv) after 50th alt. 100th cycle (4 samples)... : After ageing, voltage drop (mv) after 10th alt. 25th cycle (4 samples)... : After ageing, voltage drop (mv) after 50th alt. 100th cycle (4 samples)... : (15.7) Terminals external wiring Terminal size and rating (15.8.1) ull test spring-type terminals (4 samples); pull () ull test pin or tab terminals (4 samples); pull () (15.9) Contact resistance test Voltage drop (mv) after 1 h terminal voltage drop (mv) Voltage drop of two inseparable joints Voltage drop after 10th alt. 25th cycle Max. allowed voltage drop (mv)... : terminal voltage drop (mv) age 26 of 52

28 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS Tables Voltage drop after 50th alt. 100th cycle Max. allowed voltage drop (mv)... : terminal voltage drop (mv) Continued ageing: voltage drop after 10th alt. 25th cycle Max. allowed voltage drop (mv)... : terminal voltage drop (mv) Continued ageing: voltage drop after 50th alt. 100th cycle Max. allowed voltage drop (mv)... : terminal voltage drop (mv) AEX 5 EMF The tested product also complies to the requirements of E 62493: Limit Measured max.: 0.17 age 27 of 52

29 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS Attachment o.1 TEST REORT E hotobiological safety of lamps and lamp systems Report reference o....: See report E Tested by(name + signature)...: See report E Approved by(name + signature)...: See report E Date of issue...: See report E Contents...: See report E Testing laboratory ame... : See report E Address... : See report E Testing location...: See report E Client ame...: See report E Address...: See report E Manufacturer ame...: See report E Address...: See report E Test specification Standard...: E 62471: 2008 Test procedure...: Compliance with E 62471: 2008 on-standard test method...:.a. Test item Description...: See report E Trademark...: See report E Model and/or type reference...: See report E Rating(s)...: See report E age 28 of 52

30 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS E SCOE More sections applicable... Yes [ ] o [ ] 4 EXOSURE LIMITS 4.1 General The exposure limits in this standard apply to continuous sources where the exposure duration is not less than 0,01 ms and not more than any 8-hour period, and should be used as guides in the control of exposure. The values should not be regarded as precisely defined lines between safe and unsafe levels. detailed spectral data of a light source are generally required only if the luminance of the source exceeds 104 cd m Specific factors involved in the determination and application of retinal exposure limits See clause upil diameter Angular subtense of source and measurement field-of-view 4.3 Hazard exposure limits Actinic UV hazard exposure limit for the skin and eye The limits for exposure to ultraviolet radiation incident upon the unprotected skin or eye apply to exposure within any 8- hour period. To protect against injury of the eye or skin from ultraviolet radiation exposure produced by a broadband source, the effective integrated spectral irradiance, Es, of the light source shall not exceed the levels defined by: 400 Es t = Eλ ( λ t) SUV( λ)δt Δλ J m -2, 200 t The permissible time for exposure to ultraviolet radiation incident upon the unprotected eye or skin shall be computed by: t max 30 = E s LED light source ear-uv hazard exposure limit for the eye age 29 of 52

31 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS E For the spectral region 315 nm to 400 nm (UV-A) the total radiant exposure to the eye shall not exceed J m -2 for exposure times less than 1000 s. For exposure times greater than 1000 s (approximately 16 minutes) the UV-A irradiance for the unprotected eye, EUVA, shall not exceed 10 W m E t = Eλ ( λ t) Δt Δλ 1000 SUV, 315 J m -2 ( (t < 1000 s) t The permissible time for exposure to ultraviolet radiation incident upon the unprotected eye for times less than 1000 s, shall be computed by: t max 1000 E S UVA Retinal blue light hazard exposure limit To protect against retinal photochemical injury from chronic blue-light exposure, the integrated spectral radiance of the light source weighted against the blue-light hazard function, B(λ), i.e., the blue light weighted radiance, LB, shall not exceed the levels defined by: L t = L ( λ t) B Δt Δλ 1 B J m -2 sr -1 B 700 λ, 300 t ( λ) 4 (for t 10 s ) 700 For t>10 4 S λ ( λ) Δλ 100 W m -2 sr L = L B Retinal blue light hazard exposure limit - small source Thus the spectral irradiance at the eye Eλ, weighted against the blue-light hazard function B(λ) (see Table 4.2) shall not exceed the levels defined by: 700 EB t= Eλ ( λ t) B( λ) Δt Δλ , 300 t E = Eλ B( λ) Δλ 1 B 300 (for t 100s) For t 100s Retinal thermal hazard exposure limit age 30 of 52

32 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS E To protect against retinal thermal injury, the integrated spectral radiance of the light source, L λ,weighted by the burn hazard weighting function B( λ ) (from Figure 4.2 and Table 4.2), i.e., the burn hazard weighted radiance, shall not exceed the levels defined by: LR = Lλ B( λ) Δλ J m α t 2 sr -1 10us t 10s Retinal thermal hazard exposure limit weak visual stimulus For an infrared heat lamp or any nearinfrared source where a weak visual stimulus is inadequate to activate the aversion response, the near infrared (780 nm to 1400 nm) radiance, LIR, as viewed by the eye for exposure times greater than 10 s shall be limited to: t>10s LIR = Lλ B( λ) Δλ J m -2 sr -1 α Infrared radiation hazard exposure limits for the eye To avoid thermal injury of the cornea and possible delayed effects upon the lens of the eye (cataractogenesis), ocular exposure to infrared radiation, EIR, over the wavelength range 780 nm to 3000 nm, for times less than 1000 s, shall not exceed: IR 3000 T 1000s 0.75 λ Δλ 1800 W m E = E t For times greater than 1000 s the limit becomes: 3000 T>1000s EIR = E λ Δλ 100 W m Thermal hazard exposure limit for the skin Visible and infrared radiant exposure (380 nm to 3000 nm) of the skin shall be limited to: 3000 EH t = Eλ ( λ, t) Δλ t 380 t 0.25 age 31 of 52

33 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS E MEASUREMET OF LAMS AD LAM SYSTEMS 5.1 Measurement conditions Measurement conditions shall be reported as part of the evaluation against the exposure limits and the assignment of risk classification Lamp ageing (seasoning)... Seasoning of lamps shall be done as stated in the appropriate IEC lamp standard Test environment... For specific test conditions, see the appropriate IEC lamp standard or in the absence of such standards, the appropriate national standards or manufacturer s recommendations Extraneous radiation... Careful checks should be made to ensure that extraneous sources of radiation and reflections do not add significantly to the measurement results Lamp operation... Operation of the test lamp shall be provided in accordance with: --the appropriate IEC lamp standard. --the lamp manufacturer s recommendation Lamp system operation... The power source for operation of the test lamp shall be provided in accordance with --the appropriate IEC standard. -- the lamp manufacturer s recommendation 5.2 Measurement procedure Irradiance measurements... minimum input aperture diameter of 7 mm maximum input aperture diameter of 50 mm The measurement shall be made in that position of the beam giving the maximum reading. The measurement instrument is adequate calibrated Radiance measurements Standard method... The measurement made with an optical system age 32 of 52

34 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS E The instrument shall be calibrated to read in absolute incident radiant power per unit receiving area and per unit solid angle of acceptance averaged over the field of view (FOV) of the instrument Alternative method... Alternative to an imaging radiance set-up, an irradiance measurement set-up with a circular field stop placed at the source can be used to perform radiance measurements Measurement of source size... The determination of a, the angle subtended ba a source, requires the determination of the 50% emission point of the source ulse width measurement for pulsed sources... The determination of Δt, the nominal pulse duration of a source, requires the determination of the time during which the emission is > 50% of its peak value Analysis methods Weighting curve interpolations... The standardize interpolated values, use linear interpolation on the log of given values to obtion intermediate point at the wavelength internals de-sired. See table Calculations... The calculation of source hazard values shall be performed by weighting the spectral scan by the appropriate function and calculating the total weighted energy Measurement uncertainty... The quality of all measurement results must be quantified by an analysis of the uncertainty. See annex C 6 LAM CLASSIFICATIO For the purposes of this standard it was decided that the values shall be reported as follows: for lamps intended for general lighting service (GLS), the hazard values shall be reported as either irradiance or radiance values at a distance which produces an illuminance of 500 lux, but not at a distance less than 200 mm; age 33 of 52

35 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS E for all other light sources, including pulsed lamp sources, the hazard values shall be reported at a distance of 200 mm. 6.1 Continuous wave lamps Class I Laser roduct Exempt group the exempt group are lamps, which does not pose any photobiological. This requirement is met by any lamp that does not pose --an actinic ultraviolet hazard (Es) within 8- hours exposure (30000 s), nor --a near-uv hazard (EUVA) within 1000 s, (about 16 min) nor --a retinal blue-light hazard (LB) within s (about 2,8 h), nor --a retinal thermal hazard (LR) within 10 s, nor --an infrared radiation hazard for the eye (EIR) within 1000 s Risk Group 1 (Low-Risk) In this group are lamps, which exceeds the limited for the except group but that does not pose: --an actinic ultraviolet hazard (Es) within s, nor --a near ultraviolet hazard (EUVA) within 300 s, nor --a retinal blue-light hazard (LB) within 100 s, nor --a retinal thermal hazard (LR) within 10 s, nor --an infrared radiation hazard for the eye (EIR) within 100 s. lamps that emit infrared radiation without a strong visual stimulus (i.e., less than 10 cd m -2 ) and do not pose a near-infrared retinal hazard (LIR), within 100 s are in Risk Group 1 (Low-Risk) Risk Group 2 (Moderate-Risk) This requirement is met by any lamp that exceeds the limits for risk Group 1, but that does not pose: --an actinic ultraviolet hazard (Es) within 1000 s exposure, nor --a near ultraviolet hazard (EUVA) within 100 s, nor --a retinal blue-light hazard (LB) within 0,25 s (aversion response), nor --a retinal thermal hazard (LR) within 0,25 s (aversion response), nor --an infrared radiation hazard for the eye (EIR) within 10 s. age 34 of 52

36 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS E lamps that emit infrared radiation without a strong visual stimulus (i.e., less than 10 cd m -2 ) and do not pose a near infrared retinal hazard (LIR) within 10 s are in Risk Group 2 (Moderate-Risk) Risk Group 3 (High-Risk) Lamps which exceed the limits for Risk Group 2 (Moderate-Risk) are in Risk Group3 (High-Risk). 6.2 ulsed lamps ulsed lamp criteria shall apply to a single pulse and to any group of pulses within 0 25 second A pulsed lamp shall be evaluated at the highest nominal energy loading as specified by the manufacturer The risk group determination of the lamp being tested shall be made as follows: -- A lamp that exceeds the exposure limit shall be classified as belonging to Risk Group 3 (High-Risk). -- For single pulsed lamps, a lamp whose weighted radiant exposure or weighted radiance dose is below the EL shall be classified as belonging to the Exempt Group. -- For repetitively pulsed lamps, a lamp whose weighted radiant exposure or weighted radiance dose is below the EL, shall be evaluated using the Continuous wave risk criteria discussed in clause 6.1, using time averaged values of the pulsed emission. AEX A SUMMARY OF BIOLOGICAL EFFECTS -- Bioeffect datasheet #1: Infrared cataract A.1 Bioeffect: IFRARED CATARACT also known as "industrial heat cataract, "furnaceman's cataract", or "glassblower's cataract". A.1.1 Organ/Site: Eye/Crystalline Lens. A.1.2 A.1.3 A.1.4 Spectral range: 700 nm to 1400 nm and possibly to 3000 nm. eak of action spectrum: ot known; probably between nm. State of knowledge: Limited threshold data available for acute cataract for rabbit at 1064 nm (Wolbarsht, 1992) and lr-a region (itts and Cullen, 1981); no data for man. Degree of additivity and action spectrum unknown. Good epidemiological evidence (Lydahl, 1984). age 35 of 52

37 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS E A.1.5 A.1.6 Time course: oticeable clouding of the lens generally following years of chronic high-level exposure, the elapsed time depending upon how much difference between exposure and threshold, heavy exposures producing reaction in shortest time. Mechanism: Generally presumed to be thermal, although recent evidence suggests possible photochemical reaction - details not understood. The lens may be heated either from direct irradiation (Vogt, 1919) or by conductive heating from the heated iris (Goldman, 1983). A.1.7 Symptoms: Clouding of vision. A.1.8 A.1.9 eeded information: Action spectrum, if existent, for acute and for effects of concomitant ultraviolet radiation exposure; additivity of multiple exposures, and the possibility of delayed effects from recurrent exposures. Experience with lamps: Accidental injury is not known, even from exposure to heat lamps. Limited population exposed. A.1.10 Key references Bioeffect datasheet #2 -- A.2 Bioeffect A.2.1 Organ/Site A.2.2 Spectral range A.2.3 eak of action spectrum A.2.4 State of knowledge A.2.5 Time course A.2.6 Mechanism A.2.7 Symptoms A.2.8 eeded information A.2.9 Experience with lamps A.2.10 Key references Bioeffect datasheet #3 -- A.3 Bioeffect A.3.1 Organ/Site A.3.2 Spectral range A.3.3 eak of action spectrum A.3.4 State of knowledge age 36 of 52

38 SHEZHE LCS COMLIACE TESTIG LABORATORY LTD. REORT O.: LCS TS E A.3.5 Time course A.3.6 Mechanism A.3.7 Symptoms A.3.8 eeded information A.3.9 Experience with lamps A.3.10 Key references Bioeffect datasheet #4 -- A.4 Bioeffect A.4.1 Organ/Site A.4.2 Spectral range A.4.3 eak of action spectrum A.4.4 State of knowledge A.4.5 Time course A.4.6 Mechanism A.4.7 Symptoms A.3.8 eeded information A.4.9 Experience with lamps A.4.10 Key references Bioeffect datasheet #5 -- A.5 Bioeffect A.5.1 Organ/Site A.5.2 Spectral range A.5.3 eak of action spectrum A.5.4 State of knowledge A.5.5 Time course A.5.6 Mechanism A.5.7 Symptoms A.5.8 eeded information A.5.9 Experience with lamps A.5.10 Key references AEX B MEASUREMET METHOD B.1 Instrumentation B.1.1 Double monochromator: Recommended instrument B.1.2 Broadband detectors B.2 Instrument limitations B.2.1 oise equivalent irradiance age 37 of 52