PRODUCT: CERAMIC DISC CAPACITOR

Transcription

1 PRODUCT: CERAMIC DISC CAPACITOR TYPE: 50V, 100V, 500V, 1KV, 2KV, TEMPERATURE COMPENSATING CAPACITOR CUSTOMER: DOC. NO.: Ver.: 6 APPROVED BY CUSTOMER POE INTERNATIONAL CORPORATION 11F, NO. 480, RUEIGUANG RD., NEIHU CHIU TAIPEI, 114 TAIWAN, R.O.C.

2 50V, 100V, 500V, 1KV, 2KV TEMPERATURE COMPENSATING CERAMIC DISC CAPACITOR Ver: 6 Page: 1 1. SCOPE: THIS SPECIFICATION APPLIES TO TEMPERATURE COMPENSATING CERAMIC DISC CAPACITOR. 2. TEST CONDITIONS : UNLESS OTHERWISE SPECIFIED, ALL TESTS SHALL BE OPERATED AT THE STANDARD TEST CONDITIONS OF TEMPERATURE 5 TO 35 AND RELATIVE HUMIDITY 45% TO 85%. WHEN FAILS A TEST, RETEST BE OPERATED AT THE CONDITIONS OF TEMPERATURE 25 ± 2, RELATIVE HUMIDITY OF 60% TO 70% AND BAROMETRIC PRESSURE 860 TO 1060 MBAR. 3. HANDLE PROCEDURE : TO AVOID UNEXPECT TESTING RESULTS FROM OCCURRING, THE TESTED CAPACITOR MUST BE KEPT AT ROOM TEMPERATURE FOR AT LEAST 30 MINUTES AND COMPLETELY DISCHARGED. 4. TEST ITEMS : ITEM POST-TEST REQUIREMENTS TESTING PROCEDURE APPEARANCE STRUCTURE SIZE NO ABNORMALITIES AS SECTION 5. MARKING AS STATED IN SECTION 5 BETWEEN TERMINALS: NO ABNORMALITIES A. BELOW 1KV: 300% RATED VOLTAGE WITH 50mA MAX. CHARGING CURRENT FOR 1 5 SEC. B. 1KV & ABOVE: 200% RATED VOLTAGE WITH 50mA MAX. CHARGING CURRENT FOR 1 5 SEC. WITHSTAND VOLTAGE INSULATION RESISTANCE CAPACITANCE TEMPERATURE RANGE FACTOR BETWEEN TERMINAL AND ENCLOSURE : NO ABNORMALITIES M MIN TOLERANCE : C : ±0.25PF D : ±0.50PF J : ±5% K : ±10% PF & ABOVE BELOW 30PF C U & SL Q 1000 Q C SMALL METALLIC BALLS WITH 1mm DIAMETERS SHALL BE PUT ON A VESSEL AND THE TEST CAPACITOR SHALL BE SUBMERGED EXCEPT 2mm FROM THE TOP OF ITS COMPONENT BODY. THE TEST VOLTAGE SHALL BE APPLIED BETWEEN THE SHORT-CIRCUITED TERMINALS AND THE METALLIC BALLS. (APPLY 1.3KV DC OF RATED VOLTAGE BETWEEN TERMINALS AND ENCLOSURE FOR 1 5 SEC) INSULATION RESISTANCE SHALL BE MEASURED AT 60±5 SECONDS AFTER APPLIED VOLTAGE (RATED) RATED VOLTAGE: 50V=50V, 100V=100V, 500V & ABOVE=500V TESTING FREQUENCY : 1 MHZ ± 20% TESTING VOLTAGE : 1.0 VRMS AS ABOVE STIPULATION OF CAPACITANCE

3 50V, 100V, 500V, 1KV, 2KV TEMPERATURE COMPENSATING CERAMIC DISC CAPACITOR Ver: 6 Page: 2 ITEM POST-TEST REQUIREMENTS TESTING PROCEDURE TEMPERATURE CHARACTERISTIC TEMPERATURE COEFFICIENT : CH : 0±60 PPM/ PH : -150±60 PPM/ RH : -220±60 PPM/ SH : -330±60 PPM/ UJ : -750±120 PPM/ SL : PPM/ FOR (+20 ~+85 ) ACCORDING TO STEP 1 TO 5 IN ORDER, MEASURED CAPACITANCE WHEN TEMPERATURE REACH BALANCE AND TEMPERATURE COEFFICIENT SHALL BE CALCULATED ON THE FOLLOWING FORMULA : PPM/ =(C2-C1) 10E6/C1(T2-T1) STEP 1,3,5 : 25 STEP 2 : -25 (SL : 20 ) STEP 4 : 85 NOTE : C1 = CAPACITANCE AS STEP 3 C2 = CAPACITANCE AS STEP 2 OR 4 T1 = TEMPERATURE AS STEP 3 T2 = TEMPERATURE AS STEP 2 OR 4 TERMINAL STRENGTH SOLDERING HEAT RESISTANCE SOLDERABILITY CAPACITANCE TOLERANCE : WITHIN ±0.2% OR ±0.05PF, WHICHEVER IS LARGE TENSIBLE STRENGTH : NO BREAKDOWN BENDING STRENGTH : NO BREAKDOWN APPEARANCE : NO ABNORMALITIES CAP.CHANGE : WITHIN ±2.5% OR ±0.25PF, WHICHEVER IS LARGE. WITHSTAND VOLTAGE : (BETWEEN TERMINALS) NO ABNORMALITIES LEAD WIRE SHALL BE SOLDERED OVER 75 OF THE CIRCUMFERENTIAL DIRECTION. ACCORDING TO ABOVE STEP 1,3 & 5, CAPACITANCE TOLERANCE SHALL BE CALCULATED ON THE FOLLOWING FORMULA : C%=(G - S)/C1 NOTE : G = GREATEST CAPACITANCE AS TESTING RESULT OF STEP 1,3 & 5 S = LEAST CAPACITANCE AS TESTING RESULT OF STEP 1,3 & 5 C1 = CAPACITANCE AS STEP 3 WIRE DIA.0.5 M/M. LOADING WEIGHT 0.5 KGS, FOR 10±1 SECONDS. WIRE DIA.0.6 M/M. LOADING WEIGHT 1.0 KGS, FOR 10±1 SECONDS. WIRE DIA.0.5 mm, LOADING WEIGHT 0.25 KGS. WIRE DIA.0.6 mm, LOADING WEIGHT 0.5 KGS. (BENDING BACK AND FORTH 90 DEGREE TWICE) LEAD WIRE OR TERMINALS SHALL BE IMMERSED UP TO 2.0 M/M FORM BODY. (A) BODY DIA. 5.0mm: INTO THE MOLTEN SOLDER OF WHICH TEMPERATURE: 260(+5/-0) FOR 3.0±0.5 SECONDS. (B) BODY DIA. 5.0mm: INTO THE MOLTEN SOLDER OF WHICH TEMPERATURE 260(+5/-0) FOR 5~10 SECONDS. THEN LEAVE AT STANDARD TEST CONDITIONS FOR 1~2 HOURS, THEN MEASURED. WHEN SOLDERING CAPACITOR WITH A SOLDERING IRON, IT SHOULD BE PERFORMED IN FOLLOWING CONDITIONS. TEMPERATURE OF IRON-TIP: 350~400 SOLDERING IRON WATTAGE : 50W MAX. SOLDERING TIME : 3.5 SEC. MAX. TO COMPLY WITH JIS-C SOLDER TEMPERATURE255(+5/-0) AND DIPPING TIME 2±0.5 SECONDS FLUX : WEIGHT RATIO OF ROSIN 25%

4 50V, 100V, 500V, 1KV, 2KV TEMPERATURE COMPENSATING CERAMIC DISC CAPACITOR Ver: 6 Page: 3 ITEM POST-TEST REQUIREMENTS TESTING PROCEDURE HUMIDITY CHARACTERISTIC HUMIDITY LOADING HIGH TEMPERATURE LOADING APPEARANCE : NO ABNORMALITIES CAP. CHANGE : C U & SL : WITHIN ±5% OR ±0.5PF, WHICHEVER IS LARGE Q FACTOR : C U & SL : LESS THAN 10PF ==> Q C MORE THAN 10PF AND LESS THAN 30PF => Q C / 2 MORE THAN 30PF => Q 350 INSULATION RESISTANCE : 1000M MIN. APPEARANCE : NO ABNORMALITIES CAP.CHANGE : C U & SL : WITHIN ±7.5% OR ±0.75PF, WHICHEVER IS LARGE Q FACTOR : C U & SL : LESS THAN 30PF => Q C / 3 MORE THAN 30PF => Q 200 INSULATION RESISTANCE : 500M MIN. APPEARANCE : NO ABNORMALITIES CAP. CHANGE : C U & SL : WITHIN ±3% OR ±0.3PF, WHICHEVER IS LARGE Q FACTOR : C U & SL : LESS THAN 10PF => Q C MORE THAN 10PF & LESS THAN 30PF => Q C / 2 MORE THAN 30PF => Q 350 INSULATION RESISTANCE : 1000M MIN. CAPACITORS SHALL BE SUBJECTED TO A RELATIVE HUMIDITY OF 90 95% AT 40 ± 2 FOR 500(+24/-0) HOURS, THEN DRIED FOR 1 2 HOURS AND MEASURED. CAPACITORS SHALL BE SUBJECTED TO A RELATIVE HUMIDITY OF 90 95% AT 40±2 FOR 500(+24/-0) HOURS WITH RATED VOLTAGE APPLIED (LESS THAN 50mA), THAN DRIED FOR 1 2 HOURS AND MEASURED. CAPACITORS SHALL BE SUBJECTED TO A TEST OF: (A) BELOW 1KV: 200% RATED VOLTAGE WITH 50mA MAX. (B) 1KV & ABOVE: 150% RATED VOLTAGE WITH 50mA MAX. FOR 1000(+48/-0) HOURS AT 85 ± 2 (FOR C U & SL) AND THEN DRIED FOR 1 2 HOURS AND MEASURED.

5 50V, 100V, 500V, 1KV, 2KV TEMPERATURE COMPENSATING CERAMIC DISC CAPACITOR Ver: 6 Page: 4 5. Cap, Value vs. Rate voltage, product diameter & marking list: Manufacturing capacity list Cap. Value vs. Rate voltage, product diameter & type Photo: T.C CH (CLASS Temperature:-25 ~+85, T.C.C.: 0 60ppm) Rate voltage 50V & 100V 500V 1KV 2KV D D max. (mm) T max. (mm) R5 0R Packing T or B B T or B T or B T or B Coating PHENOL EPOXY Marking 1. Temperature characteristic CH No marking, but recognized by black color presented on the top of product. 2. Nominal capacitance Identified by 3-figure code. Ex. 5pF "5" 100 pf "101" 3. Capacitance 4. Rated voltage tolerance 5% J 50V Marked as underline 0.25pF C 500V No marking (is space.) 0.5pF D 1000V 2000V Marked 1kV Marked 2kV 5. Manufacturer s identification Shall be marked as " ", but D =6.0 mm and less in Dia shall be omitted.

6 50V, 100V, 500V, 1KV, 2KV TEMPERATURE COMPENSATING CERAMIC DISC CAPACITOR Ver: 6 Page: 5 Manufacturing capacity list Cap. Value vs. Rate voltage, product diameter & type Photo: T.C SL (CLASS Temperature:+20 ~+85, T.C.C.: +350 ~ -1000ppm) Rate voltage 50V 500V 1KV 2KV D D max. (mm) T max. (mm) Packing T or B T or B T or B T or B B Coating PHENOL EPOXY Marking 1. Temperature characteristic SL No marking. 2. Nominal capacitance Identified by 3-figure code. Ex. 5pF "5" 100 pf "101" 3. Capacitance 4. Rated voltage 5. Manufacturer's identification tolerance 5% J 50V Marked as underline 0.25pF C 500V No marking (is space.) 0.5pF D 1000V 2000V Marked 1kV Marked 2kV Shall be marked as " ", but D =6.0 mm and less in Dia shall be omitted.

7 50V, 100V, 500V, 1KV, 2KV TEMPERATURE COMPENSATING CERAMIC DISC CAPACITOR Ver: 6 Page: 6 Manufacturing capacity list Cap. Value vs. Rate voltage, product diameter & type Photo: T.C UJ (CLASS Temperature:-25 ~+85, T.C.C.: ppm) RH(CLASS Temperature:-25 ~+85, T.C.C.: ppm) Rate voltage 50V & 100V 500V 50V & 100V D D max. (mm) T max. (mm) Packing T or B T or B T or B Coating PHENOL Marking 1. Temperature characteristic 2. Nominal capacitance Recognized by color Identified by presented on the top of 3-figure code. product: Ex. 1. UJ by purple color 5pF "5" 2. RH by yellow 100 pf "101" color 3. Capacitance 4. Rated voltage tolerance 5% J 50V Marked as underline 0.25pF C 500V No marking (is space.) 0.5pF D 1000V 2000V Marked 1kV Marked 2kV 5. Manufacturer's identification Shall be marked as " ", but D =6.0 mm and less in Dia shall be omitted.

8 50V, 100V, 500V, 1KV, 2KV TEMPERATURE COMPENSATING CERAMIC DISC CAPACITOR Ver: 6 Page: 7 Manufacturing capacity list Cap. Value vs. Rate voltage, product diameter & type Photo: T.C PH (CLASS Temperature:-25 ~+85, T.C.C.: ppm) SH(CLASS Temperature:-25 ~+85, T.C.C.: ppm) Rate voltage 50V & 100V 500V 50V & 100V D D max. (mm) T max. (mm) Packing T or B B T or B Coating PHENO 1. Temperature 3. Capacitance 2. Nominal capacitance characteristic tolerance Marking Recognized by color Identified by 3-figure presented on the top code. of product: Ex. 1. PH: by orange color 5pF "5" 2.SH: by green color 100 pf "101" 4. Rated voltage 5% J 50V Marked as underline 0.25pF C 500V No marking (is space.) 0.5pF D 1000V 2000V Marked 1kV Marked 2kV 5. Manufacturer's identification Shall be marked as " ", but D =6.0 mm and less in Dia shall be omitted.

9 50V, 100V, 500V, 1KV, 2KV TEMPERATURE COMPENSATING CERAMIC DISC CAPACITOR Ver: 6 Page: 8 6. HOW TO ORDER CEAMIC DISC CAPACITOR TO ORDER, PLEASE SPECIFY PAN OVERSEAS PART NO. AS THE FOLLOWING EXAMPLE CH DIELECTRIC 500 VOLTAGE 101 CAPACITANCE J TOLERANCE 070 DIAMETER B KINK 20 LENGTH OR BAGGAGE C LENGTH TOLERANCE 7 PITCH B POWDER (CLASS ) T.C.(ppm/ ) CH( 0 60) CH SL ( ) PH ( ) RH ( ) SH ( ) TH ( ) UJ ( ) PH RH SH TH UJ CAPACITANCE 0.5 PF 0R5 1 PF PF PF uF uF 104 Reference 7.Kinked Lead Type Tapping COD TN AN Baggage & Pitch Length (CLASS ) T.C.( C% ) Y5E ( 4.7% ) YE Y5P ( 10% ) YP X7R ( 15% ) XR Z5U (+22-56%) Z5V (+22-82%) (CLASS ) T.C.( C% ) Y5V( %) Y5T(+22-33%) ZU ZV YV YT Y5R( 15% ) RY WV 16 VDC 25 VDC 50 VDC TOLERANCE 0.25 PF 0.50 PF 5 % 10 % 20 % % % C D J K M Z P DIAMETER 4 mm 5 mm 6 mm 10 mm 12 mm 15 mm 4E A B C D Length tolerance Length pith 100 VDC 500 VDC 1K VDC 2K VDC 3K VDC C P A B Coating

10 50V, 100V, 500V, 1KV, 2KV TEMPERATURE COMPENSATING CERAMIC DISC CAPACITOR Ver: 6 Page: 9 7. Kinked Lead Type 7-1.Disc size and lead style (unit mm) Lead type Lead Code Lead configuration Lead type Lead Code Lead configuration lead style B Type 4 lead style D Type 1 Vertical Straight B kink D lead short lead lead style X lead style M Type 5 Type 2 Outside kink lead X Double outside kink lead (GZ USE) M lead style H lead style Z Type 6 Type 3 Double Inside kink lead H outside kink lead Z (KS USE)

11 50V, 100V, 500V, 1KV, 2KV TEMPERATURE COMPENSATING CERAMIC DISC CAPACITOR Ver: 6 Page: 10 TAPING SPECIFICATIONS Item Symbol Specification Value Tolerance Remarks Body diameter D * max. See Cap. Value vs. Rate voltage, product Body thickness T * max. diameter & marking list. Lead-wire diameter d ,-0.05 Pitch of component P 12.7 ±1.0 Food hole pitch P ±0.3 Cumulative pitch erroe:1.0mm/20 pitch Food hole center to lead P ±0.7 To be measured at bottom of clinch Hole center to component center P ±1.3 Lead-to-lead distance F ,-0.2 Component alignment, F-R h 0 ±2.0 Tape width W ,-0.5 Hole-down tape width W min. Hole position W ,-0.5 Hole-down tape position W2 3.0 max Height of component form tape For straight lead type H center For kinked lead type H ±0.5 Component height H max. Lead-wire protrusion l 2.0 max. Food hole diameter D0 4.0 ±0.3 Total tape thickness t 0.7 ±0.2 Ground paper:0.5±0.1mm Length of sniped lead L 11.0 max. Coating rundown on leads For straight lead type C 1.5 max. For kinked lead type DR Don t exceed the kink lead These radial taped ceramic disc capacitors are designed especially for automatic insertion. The available types for radial typed are diameters 11.0 mm and under. THE PACKING FOR EPOXY COATING CAPACITOR WITH DISK DIAMETER OF 7 OR OVER 7 IS 1000 PCS PER BOX(AMMO) THE OTHER IS 2000 PCS PER BOX(AMMO) STRAIGHT LEAD TYPE AS WELL AS CONFIGURATIONS MEETS THE SPECIFICATION OF UNIVERSAL OR PANASERT ALSO AVAILABLE

12 50V, 100V, 500V, 1KV, 2KV TEMPERATURE COMPENSATING CERAMIC DISC CAPACITOR Ver: 6 Page: 11 8.Packaging 8-1.Pakaging Styles 1000pcs/bag Taping 2000pcs/box 9.Pb free showing Pb The mark is showing to all label

13 50V, 100V, 500V, 1KV, 2KV TEMPERATURE COMPENSATING CERAMIC DISC CAPACITOR Ver: 6 Page: 12 Caution 1.Caution(Rating) I. Operating Voltage When DC-rated capacitors are to be used in AC or ripple current circuits, be sure to maintain the Vp-p value of the applied voltage or the Vo-p which contains DC bias within the rated voltage range. When the voltage is applied to the circuit, starting or stopping may generate irregular voltage for a transit period because of resonance or switching. Be sure to use a capacitor with a rated voltage range that includes these irregular voltages. II. Operating Temperature and Self-generated Heat Keep the surface temperature of a capacitor below the upper limit of its rated operating temperature range. Be sure to take into account the heat generated by the capacitor itself. When the capacitor is used in a high frequency current, pulse current or similar current, it may self-generate heat due to dielectric loss. The frequency of the applied sine wave voltage should be less than 300kHz. The applied voltage load (*) should be such that the capacitor's self-generated heat is within 20 C at an atmosphere temperature of 25 C. When measuring, use a thermocouple of small thermal capacity-k of ø0.1mm in conditions where the capacitor is not affected by radiant heat from other components or surrounding ambient fluctuations. Excessive heat may lead to deterioration of the capacitor's characteristics and reliability. (Never attempt to perform measurement with the cooling fan running. Otherwise, accurate measurement cannot be ensured.) III. Fail-Safe When capacitor is broken, failure may result in a short circuit. Be sure to provide an appropriate fail-safe function like a fuse on your product if failure would follow an electric shock, fire or fume.

14 50V, 100V, 500V, 1KV, 2KV TEMPERATURE COMPENSATING CERAMIC DISC CAPACITOR Ver: 6 Page: 13 2.Caution (Storage and operating condition) I. Operating and storage environment The insulating coating of capacitors does not form a perfect seal; therefore, do not use or store capacitors in a corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the like are present. And avoid exposure to moisture. Before cleaning, bonding or molding this product, verify that these processes do not affect product quality by testing the performance of a cleaned, bonded or molded product in the intended equipment. Store the capacitors where the temperature and relative humidity do not exceed 10 to 40 degrees centigrade and 15 to 85 %. Use capacitors within 6 months. FAILURE TO FOLLOW THE ABOVE CAUTIONS MAY RESULT, WORST CASE, IN A SHORT CIRCUIT AND CAUSE FUMING OR PARTIAL DISPERSION WHEN THE PRODUCT IS USED. 3.Caution (Soldering and Mounting) I. Vibration and impact Do not expose a capacitor or its leads to excessive shock or vibration during use. II. Soldering When soldering this product to a PCB/PWB, do not exceed the solder heat resistance specification of the capacitor. Subjecting this product to excessive heating could melt the internal junction solder and may result in thermal shocks that can crack the ceramic element. When soldering capacitor with a soldering iron, it should be performed in following conditions. Temperature of iron-tip: 400 degrees C. max. Soldering iron wattage : 50W max. Soldering time : 3.5 sec. max. FAILURE TO FOLLOW THE ABOVE CAUTIONS MAY RESULT, WORST CASE, IN A SHORT CIRCUIT AND CAUSE FUMING OR PARTIAL DISPERSION WHEN THE PRODUCT IS USED. 4. Caution (Handling) Vibration and impact Do not expose a capacitor or its leads to excessive shock or vibration during use. FAILURE TO FOLLOW THE ABOVE CAUTIONS MAY RESULT, WORST CASE, IN A SHORT CIRCUIT AND CAUSE FUMING OR PARTIAL DISPERSION WHEN THE PRDUCT IS USED.

15 50V, 100V, 500V, 1KV, 2KV TEMPERATURE COMPENSATING CERAMIC DISC CAPACITOR Ver: 6 Page: 14 Notice 1.Notice (Soldering and Mounting) Cleaning (ultrasonic cleaning) To perform ultrasonic cleaning, observe the following conditions. Rinse bath capacity : Output of 20 watts per liter or less. Rinsing time : 5 min. maximum. Do not vibrate the PCB/PWB directly. Excessive ultrasonic cleaning may lead to fatigue destruction of the lead wires. 2.Notice (Rating) Capacitance change of capacitor I. Class 1 series (Temp. Char. SL CH ) Capacitance might change a little depending on the surrounding temperature or an applied voltage. Please contact us if you intend to use this product in a strict time constant circuit.

16 50V, 100V, 500V, 1KV, 2KV TEMPERATURE COMPENSATING CERAMIC DISC CAPACITOR Ver: 6 Page: 15 Appendix 1. DIELECTRIC VOLTAGE DIAMETER CAPACITANCE TOLERANCE LEAD OTHER (CLASS ) T.C.(ppm/ ) W.V CAPACITANCE COATING C H ( 0 ± 6 0 ) CH 16 VDC B 0.5 PF 0R5 EPOXY S L (+350~-1200) SL 25 VDC T 1 PF 010 (BULE) A P H (-150 ±60) PH 50 VDC U 10 PF 100 PHENOL R H (-220 ±60) RH 100 VDC A 100 PF 101 (ORANGE) T H (-470 ±60) TH 1 KVDC M 4700 PF 472 U J (-750 ±120) UJ 2 KVDC M KVDC M S H (-330 ±60) SH 500 VDC C 1000 PF 102 (CALSS ) T.C. ( C%) DIAMETER TOLERANCE Y5E ( ± 4. 7 % ) A 4 mm 4 ± 0.25 pf C Y5P ( ± 1 0 % ) B 5 mm 5 ± 0.50 pf D X7R ( ± 1 5 % ) X 6 mm 6 ± 5 % J Z5U (+22-56%) E 7 mm 7 ± 10 % K Z5V (+22-82%) F 8 mm 8 ± 20 % M 9 mm 9-20~+80% Z (CLASS ) 10 mm 0 0~+100 % P T.C. ( C%) 11 mm A LEAD CONFIGURATION Y5V (+22~-82%) FY 12 mm B Y5T (+22~-33%) D 13 mm C Y5R ( ± 1 5 % ) RY 14 mm D 15 mm E L STANDARD LEAD SPECIAL LEAD ITEM NO. LEAD CONF. LEAD LENGTH (mm) PITCH F (mm) ITEM NO. LEAD CONF. LEAD LENGTH (mm) PITCH F (mm) L1 BULK TAP. REEL TAP. AMMO 1 S 5 ± ± 0.8 BULK P2 S 18 ± ± S 5 ± ± 0.8 P3 S 15 ± ± 0.8 A S 5 ± 1 10 ± 1.0 P8 S 10 ± ± S 7 ± ± 0.8 P14 S 5 ± ± S 7 ± ± 0.8 P16 S 5 ± ± L 20 MIN. 2.5 ± 0.8 T2 H 15 ± ± L 20 MIN. 5.0 ± 0.8 T3 H 5 ± ± L 20 MIN. 6.4 ± 1.0 T4 H 20 MIN. 10 ± 1.0 C L 20 MIN. 10 ± 1.0 W4 L 20 MIN. 7.5 ± H 5 ± ± 0.8 X2 X 5 ± ± 1.0 B H 5 ± 1 10 ± 1.0 X3 X 5 ± 1 10 ± H 7 ± ± H 20 MIN. 5.0 ± 0.8 K L 2.5 ± 0.8 CUSTOMER SPECIFICATION TAPING R H ANY POSSIBLE PHYSICAL SPEC. L L CONFIGURATION CAN BE F L 2.5 ± 0.8 SPECIFIED, PAN OVERSEAS G L TAPING WILLBUILD THE PARTS TO H H SPEC MEET YOUR REQUIREMENTS G1 L1 H S X

17 50V, 100V, 500V, 1KV, 2KV TEMPERATURE COMPENSATING CERAMIC DISC CAPACITOR Ver: 6 Page: 16 Appendix 2. *Lead Style (Phenolic Resin Coating)(unit: mm) Lead type Lead Code Pith (F) Lead Length (L) Packing Lead Configuration Lead style L MIN. Type L Straight long lead Lead style S Type S Straight short lead Lead style H or B Type H or B Inside kink lead MIN MIN. C MIN. W MIN. K L Tap. Reel -0.2 Taping SPEC. F G Tap. Ammo A P P S S S P P P A A A A A A P P P B MIN B B B H H H H H H E5 5.0± E7 7.5± E0 10± T T T MIN. R Tap. Reel H Taping SPEC Tap. Ammo

18 50V, 100V, 500V, 1KV, 2KV TEMPERATURE COMPENSATING CERAMIC DISC CAPACITOR Ver: 6 Page: 17 Lead type Lead Code Pith (F) Lead Length (L) Packing Lead Configuration Lead style X Type X Outside kink lead Lead style D Type D Vertical kink short lead Lead style L1 Type L1 Straight long lead (1) X X X X X Q Q Q Q5 5.0± Q7 7.5± Q0 10± X X Taping SPEC D D D D D D Tap. Ammo D Taping SPEC. Tap. Ammo G MIN. G Taping SPEC. Tap. Ammo Lead style Z Type Z Double outside kink lead (1) Lead style XX Type XX Double outside kink lead (2) Z Z Z X X X

19 50V, 100V, 500V, 1KV, 2KV TEMPERATURE COMPENSATING CERAMIC DISC CAPACITOR Ver: 6 Page: 18 *Lead Style (Epoxy Resin Coating)(unit: mm) Lead type Lead Code Pith (F) Lead Length (L) Packing Lead Configuration Lead style L Type L Straight long lead 6A MIN. CA MIN. W4A MIN. L MIN. L MIN. L MIN. LA Tap. Reel Lead style S Type S Straight short lead Lead style H or B Type H or B Inside kink lead GA Taping SPEC. L7F Tap. Ammo L0T A AA A P8A P16A S7, A7, L7A S7S S7A S7W S7P S0, A0, L0A S0S S0A S0W S0P S1A S2A S3A A1A A2A A3A P5A P7A P0A A5A A7A A0A A BA A MIN. 0A T2A T3A T4A MIN. B5A B7, B7A B0, B0A H1A H2A H3A H5A H7A H0A E5A 5.0± E7A 7.5± E0A 10± RA Tap. Reel HA Taping SPEC Tap. Ammo

20 50V, 100V, 500V, 1KV, 2KV TEMPERATURE COMPENSATING CERAMIC DISC CAPACITOR Ver: 6 Page: 19 Lead type Lead Code Pith (F) Lead Length (L) Packing Lead Configuration Lead style X Type X Outside kink lead Lead style D Type D Vertical kink short lead X2A X3A X7, X7A X0, X0A Q1A Q2A Q3A Q5A 5.0± Q7A 7.5± Q0A 10± XA X1A X7F Taping SPEC. X0T D7, D7A D0, D0A D1A D2A D3A Tap. Ammo Lead style L1 Type L1 Straight long lead (1) DA D7F Taping SPEC. Tap. Ammo D0T G2A MIN. G1A Taping SPEC. Tap. Ammo Lead style Z Type Z Double outside kink lead (1) Lead style XX Type XX Double outside kink lead (2) Z1A Z2A Z3A X6A X4A X5A