Chapter 2: Pressure Distribution in a Fluid
|
|
- Briana West
- 5 years ago
- Views:
Transcription
1 58:6 Chapter Professor Fred Stern Fall 6 Chapter : Pressure Distribution in a Fluid Pressure and pressure gradient In fluid statics, as well as in fluid dnamics, the forces acting on a portion of fluid (CV) bounded b a CS are of two kinds: bod forces and surface forces. Bod Forces: act on the entire bod of the fluid (force per unit volume). Surface Forces: act at the CS and are due to the surrounding medium (force/unit areastress). In general the surface forces can be resolved into two components: one normal and one tangential to the surface. Considering a cubical fluid element, we see that the stress in a moving fluid comprises a nd order tensor. σ Face σz σ Direction z
2 58:6 Chapter Professor Fred Stern Fall 6 σ ij σ σ σ z σ σ σ z σ z σ z σ zz Since b definition, a fluid cannot withstand a shear stress without moving (deformation), a stationar fluid must necessaril be completel free of shear stress (σij, i j). The onl non-zero stress is the normal stress, which is referred to as pressure: n σii-p σ n -p, which is compressive, as it should be since fluid cannot withstand tension. (Sign convention based on the fact that p> and in the direction of n) Or p p p z p n p (one value at a point, independent of direction; p is a scalar) i.e. normal stress (pressure) is isotropic. This can be easil seen b considering the equilibrium of a wedge shaped fluid element
3 58:6 Chapter Professor Fred Stern Fall 6 3 F : p dasinα p dasinα n p p n F : p dacosα + p dacosα W z n z Where: W γv V z l cosα z l sin α l pnda dl da z α pdasinα α dadld WρgVγV pzdacosα da / dl W p n γda cosα dl sin α p n p da n + p z p z cosα + for dl p da z γ dl sin α i.e. cosα γda cosα dl sin α p n p p p z Note: For a fluid in motion, the normal stress is different on each face and not equal to p. σ σ σzz -p B convention p is defined as the average of the normal stresses p ( σ + σ + σzz ) σii 3 3
4 58:6 Chapter Professor Fred Stern Fall 6 4 The fluid element eperiences a force on it as a result of the fluid pressure distribution if it varies spatiall. Consider the net force in the direction due to p(,t). d d dz The result will be similar for df and dfz; consequentl, we conclude: p ˆ p ˆ p df ˆ press i j k z Or: f p force per unit volume due to p(,t). Note: if pconstant, f.
5 58:6 Chapter Professor Fred Stern Fall 6 5 Equilibrium of a fluid element Consider now a fluid element which is acted upon b both surface forces and a bod force due to gravit df ρ gd or ρ g (per unit volume) grav f grav Application of Newton s law ields: ρd a ( f ) d ρa f f + bod f surface per unit d m a F f bod g and g gkˆ f ρg kˆ bod f f + f surface pressure viscous (includes f, since in general σij viscous pδij τij ρ z g + ) Viscous part f p pressure V V V f µ + + µ V viscous z For ρ, μconstant, the viscous force will have this form (chapter 4). V t ρa p+ ρ g+ µ V with + V V inertial pressure gradient gravit viscous a
6 58:6 Chapter Professor Fred Stern Fall 6 6 This is called the Navier-Stokes equation and will be discussed further in Chapter 4. Consider solving the N-S equation for p when a and V are known. p ρ g a + µ V B(, t ( ) ) This is simpl a first order PDE for p and can be solved readil. For the general case (V and p unknown), one must solve the NS and continuit equations, which is a formidable task since the NS equations are a sstem of nd order nonlinear PDEs. We now consider the following special cases: ) Hdrostatics ( V a ) V ) ) Rigid bod translation or rotation ( 3) Irrotational motion ( ( a) ( a) a vector identit V ) V if ρ constant V Euler equation Bernoulli equation also, V V ϕ if ρ const ϕ &.
7 58:6 Chapter Professor Fred Stern Fall 6 7 Case () Hdrostatic Pressure Distribution p ρg ρgk z g p p i.e. and p ρ g z dp ρgdz or p p ρ gdz g ρ( z) dz r g g r constant near earth's surface r liquids ρ constant (for one liquid) p -ρgz + constant gases ρ ρ(p,t) which is known from the equation of state: p ρrt ρ p/rt dp p g R dz T (z) which can be integrated if T T(z) is known as it is for the atmosphere.
8 58:6 Chapter Professor Fred Stern Fall 6 8 Manometr Manometers are devices that use liquid columns for measuring differences in pressure. A general procedure ma be followed in working all manometer problems:.) Start at one end (or a meniscus if the circuit is continuous) and write the pressure there in an appropriate unit or smbol if it is unknown..) Add to this the change in pressure (in the same unit) from one meniscus to the net (plus if the net meniscus is lower, minus if higher). 3.) Continue until the other end of the gage (or starting meniscus) is reached and equate the epression to the pressure at that point, known or unknown.
9 58:6 Chapter Professor Fred Stern Fall 6 9 Hdrostatic forces on plane surfaces The force on a bod due to a pressure distribution is: F pn da A where for a plane surface n constant and we need onl consider F noting that its direction is alwas towards the surface: F p da. A Consider a plane surface AB entirel submerged in a liquid such that the plane of the surface intersects the freesurface with an angle α. The centroid of the surface is denoted (, ). F γ sinαa pa Where p is the pressure at the centroid.
10 58:6 Chapter Professor Fred Stern Fall 6 To find the line of action of the force which we call the center of pressure (cp, cp) we equate the moment of the resultant force to that of the distributed force about an arbitrar ais. cpf df A Note: df γsinαda γ sinα da A da I moment of Inertia about O O o A A + I I moment of inertia WRT horizontal centroidal ais F pa γ sinαa cpγ sinαa γ sinα( A+ I) cp + I A and similarl for cp cp cp F df A I + A where I I product of I + A inertia Note that the coordinate sstem in the tet has its origin at the centroid and is related to the one just used b: tet and tet ( )
11 58:6 Chapter Professor Fred Stern Fall 6 Hdrostatic Forces on Curved Surfaces z In general, F A pn da Horizontal Components: F F i p n i da da F A p da da projection of n da onto a plane perpendicular to direction da projection of n da onto a plane perpendicular to direction The horizontal component of force acting on a curved surface is equal to the force acting on a vertical projection of that surface including both magnitude and line of action and can be determined b the methods developed for plane surfaces. F pn k da p da γ h daz δ γ z z A Az z Where h is the depth to an element area da of the surface. The vertical component of force acting on a curved surface is equal to the net weight of the total column of fluid directl above the curved surface and has a line of action through the centroid of the fluid volume.
12 58:6 Chapter Professor Fred Stern Fall 6 Eample Drum Gate hr-rcosθr(-cosθ) p γh γ R cosθ ( ) h n sinθ i+ cosθk da lrdθ π ( cosθ )( sinθiˆ cosθkˆ ) lrd + da F γr p π ( cosθ ) θdθ F.ˆ i F γlr sin γlr cosθ γrrl A p π + n θ π cos θ γlr 4 Same force as that on projection of gate onto vertical plane perpendicular direction
13 58:6 Chapter Professor Fred Stern Fall 6 3 ( ) cos cos z F lr d π γ θ θ θ γ π γ π γ γ θ θ θ γ π sin 4 sin R l lr lr lr Another approach: γ π π γ π γ π γ l R F F F F l R F lr l R l R F / / + Net weight of water above curved surface
14 58:6 Chapter Professor Fred Stern Fall 6 4 Hdrostatic Forces in Laered Fluids See tetbook.7 Buoanc and Stabilit Archimedes Principle F B F V ( ) F V () fluid weight above ABC fluid weight above ADC weight of fluid equivalent to the bod volume In general, FB ρg ( submerged volume). The line of action is through the centroid of the displaced volume, which is called the center of buoanc.
15 58:6 Chapter Professor Fred Stern Fall 6 5 Eample: Floating bod in heave motion L G ddraft ρ b B h b W ρ Weight of the block b Lb hg mg γ where is A displaced water volume b the block and γ is the specific weight of the liquid. W ρb ρw ρb > ρw ρ < ρ b ρb B ρblbhg ρwlbdg d ρ w : d : d : d W B h > h sink < h floating Instantaneous displaced water volume: V A wp.. F m B W γ γ γ A wp wp w h S b h
16 58:6 Chapter Professor Fred Stern Fall m+ γ A A wp wp.. γ + m Acosω t+ Bsinω t Use initial condition ( and B: Where n n.. t, ) to determine A. cosωn sin ωn t+ ω t ω n γ A m wp n period T π m π ω γa Spar Buo wp T is tuned to decrease response to ambient waves: we can increase T b increasing block mass m and/or decreasing waterline area A wp.
17 58:6 Chapter Professor Fred Stern Fall 6 7 Stabilit: Immersed Bodies Stable Neutral Unstable Condition for static equilibrium: () Fv and () M Condition () is met onl when C and G coincide, otherwise we can have either a righting moment (stable) or a heeling moment (unstable) when the bod is heeled. Stabilit: Floating Bodies For a floating bod the situation is more complicated since the center of buoanc will generall shift when the bod is rotated, depending upon the shape of the bod and the position in which it is floating.
18 58:6 Chapter Professor Fred Stern Fall 6 8 The center of buoanc (centroid of the displaced volume) shifts laterall to the right for the case shown because part of the original buoant volume AOB is transferred to a new buoant volume EOD. The point of intersection of the lines of action of the buoant force before and after heel is called the metacenter M and the distance GM is called the metacentric height. If GM is positive, that is, if M is above G, then the ship is stable; however, if GM is negative, then the ship is unstable.
19 58:6 Chapter Professor Fred Stern Fall 6 9 Consider a ship which has taken a small angle of heel α. αsmall heel angle. evaluate the lateral displacement of the center of buoanc, CC 3. then from trigonometr, we can solve for GM and evaluate the stabilit of the ship: centroid; CMGM+CG Recall that the center of buoanc is at the centroid of the displaced volume of fluid (moment of volume about - ais ship centerplane) d i i This can be evaluated convenientl as follows: moment of before heel (goes to zero due to smmetr of original buoant volume AKKD about centerplane) - moment of AOB + moment of EOD
20 58:6 Chapter Professor Fred Stern Fall 6 ( ) d ( d + ) AOB tan α d da tanα da DOE OA tanα da + tanα da tan OD α da ship waterplane area (moment of inertia of ship waterplane I, i.e, I zz ) I tanα CC ' I tan α CC ' CM tanα (from Section View) CM I
21 58:6 Chapter Professor Fred Stern Fall 6 GM CM CG, i.e. CMGM+CG GM I CG This equation is used to determine the stabilit of floating bodies: If GM is positive, the bod is stable If GM is negative, the bod is unstable
22 58:6 Chapter Professor Fred Stern Fall 6 Roll: The rotation of a ship about the longitudinal ais through the center of gravit. Consider smmetrical ship heeled to a ver small angle θ. Solve for the subsequent motion due onl to hdrostatic and gravitational forces. ( cos θˆj sinθiˆ ) ρ F b g M r M g g F b ( GCj ˆ + CC iˆ ) ( cosθˆj sinθiˆ ) ( GC sinθ + CC cosθ ) ( GC + GM ) sinθ kˆ GM sinθ kˆ kˆ ( ρ g Δ) Note: recall that M o F d, where d is the perpendicular distance from O to the line of action of F. d M G GZ GM sinθ O F
23 58:6 Chapter Professor Fred Stern Fall 6 3 CC' tan θ CM.. I θ M G sinθ cosθ I mass moment of inertia about long ais through G.. θ angular acceleration.. I θ+ GM sinθ.. GM for small θ : θ + θ I GM ρg GM mggm I I I k I definition of radius of gration m k I m GM I ggm k mk I The solution to this equation is, where. θo θ ( t) θ cosω t + sinω t o n n ωn θ the initial heel angle o for no initial velocit ω n natural frequenc ggm k ggm k
24 58:6 Chapter Professor Fred Stern Fall 6 4 Simple (undamped) harmonic oscillation: The period of the motion is T π ω n T πk ggm Note that large GM decreases the period of roll, which would make for an uncomfortable boat ride (high frequenc oscillation). Earlier we found that GM should be positive if a ship is to have transverse stabilit and, generall speaking, the stabilit is increased for larger positive GM. However, the present eample shows that one encounters a design tradeoff since large GM decreases the period of roll, which makes for an uncomfortable ride.
25 58:6 Chapter Professor Fred Stern Fall 6 5 Parametric Roll: The periodicit of the encounter wave causes variations of the metacentric height i.e. GMGM (t). Therefore:.. I θ+ GM () t θ Assuming GM ( t) GM + GMcos( ωt) :.. I θ+ ( GM + GMcos( ωt) ) θ.. θ+ ω + Cω cos( ω t) θ where ( n n e ) ω ggm GM ; ; ; ; and encounter wave freq. n C mg I mk ωe k GM B changing of variables ( τ ω t e ):.. θτ ( ) + δ ( + C cos τ ) θτ ( ) and ωn δ ωe This ordinar nd order differential equation where the restoring moment varies sinusoidall, is known as the Mathieu equation. This equation gives unbounded solution (i.e. it is unstable) when ωn n + δ n,,,3,.. ωe For the principle parametric roll resonance, n i.e. π π ω ω T T T T e n n e e n
26 58:6 Chapter Professor Fred Stern Fall 6 6 Case () Rigid Bod Translation or Rotation In rigid bod motion, all particles are in combined translation and/or rotation and there is no relative motion between particles; consequentl, there are no strains or strain rates and the viscous term drops out of the N-S equation ( µ V ). p ρ ( g a) from which we see that p and lines of constant pressure must be perpendicular to this direction (b definition, f is perpendicular to f constant). acts in the direction of ( a) g, Rigid bod of fluid translating or rotating
27 58:6 Chapter Professor Fred Stern Fall 6 7 The general case of rigid bod translation/rotation is as shown. If the center of rotation is at O where V V, the velocit of an arbitrar point P is: V V + Ω r where Ω the angular velocit vector and the acceleration is: dv dt a dv dω + Ω ( Ω r ) + r dt dt 3 acceleration of O centripetal acceleration of P relative to O 3 linear acceleration of P due to Ω Usuall, all these terms are not present. In fact, fluids can rarel move in rigid bod motion unless restrained b confining walls.
28 58:6 Chapter Professor Fred Stern Fall 6 8.) Uniform Linear Acceleration pconstant p ρ g a Constant ( ) p ρ a. a < p increase in +. a > p decrease in + p ρ + z ( g a ) z. a z > p decrease in +z. az < and az < g p decrease in +z but slower than g 3. a and a g z < > p increase in +z z ρ [( ) ] ^ ^ g + a k+ a i z
29 58:6 Chapter Professor Fred Stern Fall 6 9 unit vector in the direction of p: s p p g+ a k+ ai ( ) z ( ) z g+ a + a lines of constant pressure are perpendicular to p. n s j a k g a i ( + ) z + ( + z) a g a unit vector in direction of pconstant angle between n and aes: θ tan ( g a + a z ) In general the pressure variation with depth is greater than in ordinar hdrostatics; that is: dp ds ( ) z p s ρ a + g+ a which is > ρg G p ρgs + constant ρgs gage pressure
30 58:6 Chapter Professor Fred Stern Fall 6 3 ). Rigid Bod Rotation Consider a clindrical tank of liquid rotating at a constant rate Ω Ω k : p ρ ( g a) a Ω rω ( Ω r ) ^ er p ρ ( g a) gkˆ ρ + ρrω eˆ r i.e. p ρr Ω r p ρ g z
31 58:6 Chapter Professor Fred Stern Fall 6 3 and ρ p r Ω + f ( z) + c ρ p r Ω ρgz + Constant p z f ' ρg f ( z) ρgz + C The constant is determined b specifing the pressure at one point; sa, p p at (r,z) (,). ρ p p ρ gz + r Ω (Note: Pressure is linear in z and parabolic in r) Curves of constant pressure are given b: p p ρ g r Ω g z + a + br which are paraboloids of revolution, concave upward, with their minimum points on the ais of rotation. The position of the free surface is found, as it is for linear acceleration, b conserving the volume of fluid.
32 58:6 Chapter Professor Fred Stern Fall 6 3 The unit vector in the direction of p is: ρgkˆ + ρrω eˆ r sˆ ( ρg) + ( ρrω ) / [ ] z tanθ dz dr g rω slope of s θ r i.e. r C Ω g dz Ω z g dr r Ω z g ln r ep equation of p surfaces s
33 58:6 Chapter Professor Fred Stern Fall 6 33 Case (3) Pressure Distribution in Irrotational Flow; Bernoulli Equation ρa ( p) ρgkˆ + µ V ρ t + V V V ( p + γz) + µ ( p + γz) + µ [ ( V ) ( V )] Viscous term for ρconstant and ω, i.e., Potential flow solutions also solutions NS under such conditions!. Assuming inviscid flow: µ V V ρ + / V V V ( V ) ( p + γz) t Euler Equation. Assuming incompressible flow: ρconstant V t V + p + + gz V ω ρ V V V
34 58:6 Chapter Professor Fred Stern Fall Assuming stead flow: t B V V B ω p + + ρ gz Consider: B perpendicular B constant V ω perpendicular V and ω Therefore, Bconstant contains streamlines and vorte lines:
35 58:6 Chapter Professor Fred Stern Fall Assuming irrotational flow: ω B B constant (everwhere same constant) V V 5. Unstead irrotational flow ϕ ϕ ϕ ϕ ϕ ϕ p gz t ρ ϕ ϕ ϕ p gz B( t) t ρ B(t) time dependent constant
36 58:6 Chapter Professor Fred Stern Fall 6 36
37 58:6 Chapter Professor Fred Stern Fall 6 37 Larger speed/densit or smaller R require larger pressure gradient or elevation gradient normal to streamline.
38 58:6 Chapter Professor Fred Stern Fall 6 38 Flow Patterns: Streamlines, Streaklines, Pathlines ) A streamline is a line everwhere tangent to the velocit vector at a given instant. ) A pathline is the actual path traveled b a given fluid particle. 3) A streakline is the locus of particles which have earlier passed through a particular point.
39 58:6 Chapter Professor Fred Stern Fall 6 39 Note:. For stead flow, all 3 coincide.. For unstead flow, ψ(t) pattern changes with time, whereas pathlines and streaklines are generated as the passage of time. Streamline B definition we must have V dr which upon epansion ields the equation of the streamlines for a given time t t d u d dz ds s integration parameter v w So if (u,v,w) known, integrate with respect to s for tt with IC (,,z,t) at s and then eliminate s. Pathline The pathline is defined b integration of the relationship between velocit and displacement. d dt u d dt v dz dt w Integrate u,v,w with respect to t using IC ( eliminate t.,, z, t ) then
40 58:6 Chapter Professor Fred Stern Fall 6 4 Streakline To find the streakline, use the integrated result for the pathline retaining time as a parameter. Now, find the integration constant which causes the pathline to pass through (,, z ) for a sequence of times ξ < t. Then eliminate ξ. Eample: b: an idealized velocit distribution is given u v w + t + t calculate and plot: ) the streamlines ) the pathlines 3) the streaklines which pass through (,, z ) at t..) First, note that since w there is no motion in the z direction and the flow is -D d ds + t C s at ep( and eliminating s d ds + t s s ) C ep( ) + t + t (, ) : C C
41 58:6 Chapter Professor Fred Stern Fall 6 4 s ( + t)ln ( + t)ln n + t ( ) where n + t This is the equation of the streamlines which pass through (, ) for all times t..) To find the pathlines we integrate d d dt + t dt + t C ( + t) C ( + t) t (, ) (, ) : C C now eliminate t between the equations for (, ) [ + ( )] This is the pathline through (, ) at t and does not coincide with the streamline at t.
42 58:6 Chapter Professor Fred Stern Fall ) To find the streakline, we use the pathline equations to find the famil of particles that have passed through the point (, ) for all times t < ξ. : ] ) )( [( ) ( ) )( ( ) ( ) ( ) ( ) ( t t t t t C C t C t C ξ ξ ξ
43 58:6 Chapter Professor Fred Stern Fall 6 43 The Stream Function Powerful tool for -D flown in which V is obtained b differentiation of a scalar ψ which automaticall satisfies the continuit equation. Continuit boundar conditions (4 required): at infinit : on bod : u ψ U u v ψ v ψ ψ
44 58:6 Chapter Professor Fred Stern Fall 6 44 Irrotational Flow ψ on S : on S : B nd order linear Laplace equation ψ U + const. ψ const. u ψ φ v ψ φ Ψ and φ are orthogonal. dφ φ d + φ d ud + vd dψ ψ d + ψ d vd + ud d u i.e. d φ const v d dψ const
45 58:6 Chapter Professor Fred Stern Fall 6 45 Geometric Interpretation of ψ Besides its importance mathematicall ψ also has important geometric significance. ψ constant streamline Recall definition of a streamline: V dr i.e. d d u v ud vd compare with dψ dr diˆ + dj ˆ dψ ψ d + ψ d along a streamline vd + ud Or ψ constant along a streamline and curves of constant ψ are the flow streamlines. If we know ψ (, ) then we can plot ψ constant curves to show streamlines.
46 58:6 Chapter Professor Fred Stern Fall 6 46 Phsical Interpretation dq V. nda ( ˆ ψ ˆ ψ d ).( ˆ d i j i ˆj ) ds ds ds ψ d + ψ d dψ (note that ψ and Q have same dimensions: m 3 /s) i.e. change in d ψ is volume flu and across streamline Q V. nda dψ ψ ψ Consider flow between two streamlines: dq.
47 58:6 Chapter Professor Fred Stern Fall 6 47 Incompressible Plane Flow in Polar Coordinates continuit : ( rvr ) + ( vθ ) r r r θ or : ( rvr ) + ( vθ ) r θ ψ ψ sa: vr vθ r θ r ψ ψ then ( r ) + ( ) r r θ θ r as before dψ along a streamline and dq dψ volume flu change in stream function Incompressible aismmetric flow ( ) ( ) rv + v continuit : r r r z z ψ ψ sa : v v r r z z r r ψ ψ then : r + r r r z z r r as before dψ along a streamline and dq dψ
48 58:6 Chapter Professor Fred Stern Fall 6 48 Generalization Stead plane compressible flow: constant isa streamline and i.e. ) ( compare with SL compressibleflow stream function define : ) ( ) ( ψ ψ ψ ρ ψ ψ ψ ψ ρ ψ ρ ψ ψ ρ ψ ρ ρ ρ d d d d d d d vd ud v u v u Now: ). ( ). ( ψ ψ ρ ψ ρ da n V m d da n V dm Change in ψ is equivalent to the mass flu.
Chapter 2: Pressure Distribution in a Fluid
ME:56 Chapter Professor Fred Stern Fall 7 Chapter : Pressure Distribution in a Fluid Pressure and pressure gradient In fluid statics, as well as in fluid dnamics, the forces acting on a portion of fluid
More informationChapter 2: Pressure and Fluid Statics
57:00 Fluid Mechanics Chapter Professor Fred Stern Fall 008 1 Chapter : Pressure and Fluid Statics Pressure For a static fluid, the only stress is the normal stress since by definition a fluid subjected
More informationMethod of Images
. - Marine Hdrodnamics, Spring 5 Lecture 11. - Marine Hdrodnamics Lecture 11 3.11 - Method of Images m Potential for single source: φ = ln + π m ( ) Potential for source near a wall: φ = m ln +( ) +ln
More informationV (r,t) = i ˆ u( x, y,z,t) + ˆ j v( x, y,z,t) + k ˆ w( x, y, z,t)
IV. DIFFERENTIAL RELATIONS FOR A FLUID PARTICLE This chapter presents the development and application of the basic differential equations of fluid motion. Simplifications in the general equations and common
More informationFluid Mechanics II. Newton s second law applied to a control volume
Fluid Mechanics II Stead flow momentum equation Newton s second law applied to a control volume Fluids, either in a static or dnamic motion state, impose forces on immersed bodies and confining boundaries.
More informationApply mass and momentum conservation to a differential control volume. Simple classical solutions of NS equations
Module 5: Navier-Stokes Equations: Appl mass and momentum conservation to a differential control volume Derive the Navier-Stokes equations Simple classical solutions of NS equations Use dimensional analsis
More informationPressure in stationary and moving fluid Lab- Lab On- On Chip: Lecture 2
Pressure in stationary and moving fluid Lab-On-Chip: Lecture Lecture plan what is pressure e and how it s distributed in static fluid water pressure in engineering problems buoyancy y and archimedes law;
More informationEric G. Paterson. Spring 2005
Eric G. Paterson Department of Mechanical and Nuclear Engineering Pennsylvania State University Spring 2005 Reading and Homework Read Chapter 3. Homework Set #2 has been posted. Due date: Friday 21 January.
More informationChapter 3 Bernoulli Equation
1 Bernoulli Equation 3.1 Flow Patterns: Streamlines, Pathlines, Streaklines 1) A streamline, is a line that is everywhere tangent to the velocity vector at a given instant. Examples of streamlines around
More informationFLUID MECHANICS. 1. Division of Fluid Mechanics. Hydrostatics Aerostatics Hydrodynamics Gasdynamics. v velocity p pressure ρ density
FLUID MECHANICS. Diision of Fluid Mechanics elocit p pressure densit Hdrostatics Aerostatics Hdrodnamics asdnamics. Properties of fluids Comparison of solid substances and fluids solid fluid τ F A [Pa]
More informationChapter 3 Fluid Statics
Chapter 3 Fluid Statics 3.1 Pressure Pressure : The ratio of normal force to area at a point. Pressure often varies from point to point. Pressure is a scalar quantity; it has magnitude only It produces
More informationKINEMATIC RELATIONS IN DEFORMATION OF SOLIDS
Chapter 8 KINEMATIC RELATIONS IN DEFORMATION OF SOLIDS Figure 8.1: 195 196 CHAPTER 8. KINEMATIC RELATIONS IN DEFORMATION OF SOLIDS 8.1 Motivation In Chapter 3, the conservation of linear momentum for a
More informationHydrostatics. ENGR 5961 Fluid Mechanics I: Dr. Y.S. Muzychka
1 Hydrostatics 2 Introduction In Fluid Mechanics hydrostatics considers fluids at rest: typically fluid pressure on stationary bodies and surfaces, pressure measurements, buoyancy and flotation, and fluid
More informationLagrangian description from the perspective of a parcel moving within the flow. Streamline Eulerian, tangent line to instantaneous velocity field.
Chapter 2 Hydrostatics 2.1 Review Eulerian description from the perspective of fixed points within a reference frame. Lagrangian description from the perspective of a parcel moving within the flow. Streamline
More information1.1 The Equations of Motion
1.1 The Equations of Motion In Book I, balance of forces and moments acting on an component was enforced in order to ensure that the component was in equilibrium. Here, allowance is made for stresses which
More informationIn this section, mathematical description of the motion of fluid elements moving in a flow field is
Jun. 05, 015 Chapter 6. Differential Analysis of Fluid Flow 6.1 Fluid Element Kinematics In this section, mathematical description of the motion of fluid elements moving in a flow field is given. A small
More informationPressure in stationary and moving fluid. Lab-On-Chip: Lecture 2
Pressure in stationary and moving fluid Lab-On-Chip: Lecture Fluid Statics No shearing stress.no relative movement between adjacent fluid particles, i.e. static or moving as a single block Pressure at
More informationCHAPTER 3 Introduction to Fluids in Motion
CHAPTER 3 Introduction to Fluids in Motion FE-tpe Eam Review Problems: Problems 3- to 3-9 nˆ 0 ( n ˆi+ n ˆj) (3ˆi 4 ˆj) 0 or 3n 4n 0 3. (D) 3. (C) 3.3 (D) 3.4 (C) 3.5 (B) 3.6 (C) Also n n n + since ˆn
More informationx y plane is the plane in which the stresses act, yy xy xy Figure 3.5.1: non-zero stress components acting in the x y plane
3.5 Plane Stress This section is concerned with a special two-dimensional state of stress called plane stress. It is important for two reasons: () it arises in real components (particularl in thin components
More information5.1 Fluid momentum equation Hydrostatics Archimedes theorem The vorticity equation... 42
Chapter 5 Euler s equation Contents 5.1 Fluid momentum equation........................ 39 5. Hydrostatics................................ 40 5.3 Archimedes theorem........................... 41 5.4 The
More informationChapter 1 INTRODUCTION
Chapter 1 INTRODUCTION 1-1 The Fluid. 1-2 Dimensions. 1-3 Units. 1-4 Fluid Properties. 1 1-1 The Fluid: It is the substance that deforms continuously when subjected to a shear stress. Matter Solid Fluid
More informationChapter 5 Equilibrium of a Rigid Body Objectives
Chapter 5 Equilibrium of a Rigid Bod Objectives Develop the equations of equilibrium for a rigid bod Concept of the free-bod diagram for a rigid bod Solve rigid-bod equilibrium problems using the equations
More informationFluid Mechanics. du dy
FLUID MECHANICS Technical English - I 1 th week Fluid Mechanics FLUID STATICS FLUID DYNAMICS Fluid Statics or Hydrostatics is the study of fluids at rest. The main equation required for this is Newton's
More informationDIMENSIONS AND UNITS
DIMENSIONS AND UNITS A dimension is the measure by which a physical variable is expressed quantitatively. A unit is a particular way of attaching a number to the quantitative dimension. Primary Dimension
More informationEMA 3702 Mechanics & Materials Science (Mechanics of Materials) Chapter 4 Pure Bending
EA 3702 echanics & aterials Science (echanics of aterials) Chapter 4 Pure Bending Pure Bending Ch 2 Aial Loading & Parallel Loading: uniform normal stress and shearing stress distribution Ch 3 Torsion:
More informationFluid Statics. Pressure. Pressure
Pressure Fluid Statics Variation of Pressure with Position in a Fluid Measurement of Pressure Hydrostatic Thrusts on Submerged Surfaces Plane Surfaces Curved Surfaces ddendum First and Second Moment of
More informationLecture 4. Differential Analysis of Fluid Flow Navier-Stockes equation
Lecture 4 Differential Analysis of Fluid Flow Navier-Stockes equation Newton second law and conservation of momentum & momentum-of-momentum A jet of fluid deflected by an object puts a force on the object.
More informationFluid Mechanics-61341
An-Najah National University College of Engineering Fluid Mechanics-61341 Chapter [2] Fluid Statics 1 Fluid Mechanics-2nd Semester 2010- [2] Fluid Statics Fluid Statics Problems Fluid statics refers to
More informationMechanics Departmental Exam Last updated November 2013
Mechanics Departmental Eam Last updated November 213 1. Two satellites are moving about each other in circular orbits under the influence of their mutual gravitational attractions. The satellites have
More informationOffshore Hydromechanics Module 1
Offshore Hydromechanics Module 1 Dr. ir. Pepijn de Jong 4. Potential Flows part 2 Introduction Topics of Module 1 Problems of interest Chapter 1 Hydrostatics Chapter 2 Floating stability Chapter 2 Constant
More informationMAE 101A. Homework 7 - Solutions 3/12/2018
MAE 101A Homework 7 - Solutions 3/12/2018 Munson 6.31: The stream function for a two-dimensional, nonviscous, incompressible flow field is given by the expression ψ = 2(x y) where the stream function has
More informationDepartment of Physics
Department of Physics PHYS101-051 FINAL EXAM Test Code: 100 Tuesday, 4 January 006 in Building 54 Exam Duration: 3 hrs (from 1:30pm to 3:30pm) Name: Student Number: Section Number: Page 1 1. A car starts
More informationConservation of Linear Momentum for a Differential Control Volume
Conservation of Linear Momentum for a Differential Control Volume When we applied the rate-form of the conservation of mass equation to a differential control volume (open sstem in Cartesian coordinates,
More informationDistributed Forces: Moments of Inertia
Distributed Forces: Moments of nertia Contents ntroduction Moments of nertia of an Area Moments of nertia of an Area b ntegration Polar Moments of nertia Radius of Gration of an Area Sample Problems Parallel
More informationSOLID AND FLUID MECHANICS CPE LEVEL I TRAINING MODULE
www.iacpe.com Page : 1 of 120 Rev 01- Oct 2014 IACPE No 19, Jalan Bilal Mahmood 80100 Johor Bahru Malasia CPE LEVEL I The International of is providing the introduction to the Training Module for our review.
More informationKolmetz Handbook Process Equipment Design SOLID AND FLUID MECHANICS (ENGINEERING FUNDAMENTALS)
Page : 1 of 111 Rev 01 Guidelines for Processing Plant KLM Technolog #03-12 Block Aronia, Jalan Sri Perkasa 2 Taman Tampoi Utama 81200 Johor Bahru Malasia SOLUTIONS, STANDARDS AND SOFTWARE www.klmtechgroup.com
More informationENGI 4430 Advanced Calculus for Engineering Faculty of Engineering and Applied Science Problem Set 3 Solutions [Multiple Integration; Lines of Force]
ENGI 44 Advanced Calculus for Engineering Facult of Engineering and Applied Science Problem Set Solutions [Multiple Integration; Lines of Force]. Evaluate D da over the triangular region D that is bounded
More informationAnd similarly in the other directions, so the overall result is expressed compactly as,
SQEP Tutorial Session 5: T7S0 Relates to Knowledge & Skills.5,.8 Last Update: //3 Force on an element of area; Definition of principal stresses and strains; Definition of Tresca and Mises equivalent stresses;
More informationChapter 6 Equations of Continuity and Motion
Chapter 6 Equations of Continuity and Motion Derivation of 3-D Eq. conservation of mass Continuity Eq. conservation of momentum Eq. of motion Navier-Strokes Eq. 6.1 Continuity Equation Consider differential
More informationClassical Mechanics. Luis Anchordoqui
1 Rigid Body Motion Inertia Tensor Rotational Kinetic Energy Principal Axes of Rotation Steiner s Theorem Euler s Equations for a Rigid Body Eulerian Angles Review of Fundamental Equations 2 Rigid body
More informationP = ρ{ g a } + µ 2 V II. FLUID STATICS
II. FLUID STATICS From a force analysis on a triangular fluid element at rest, the following three concepts are easily developed: For a continuous, hydrostatic, shear free fluid: 1. Pressure is constant
More informationIntroduction to Marine Hydrodynamics
1896 1920 1987 2006 Introduction to Marine Hydrodynamics (NA235) Department of Naval Architecture and Ocean Engineering School of Naval Architecture, Ocean & Civil Engineering Shanghai Jiao Tong University
More informationCH.7. PLANE LINEAR ELASTICITY. Multimedia Course on Continuum Mechanics
CH.7. PLANE LINEAR ELASTICITY Multimedia Course on Continuum Mechanics Overview Plane Linear Elasticit Theor Plane Stress Simplifing Hpothesis Strain Field Constitutive Equation Displacement Field The
More informationChapter 14. Lecture 1 Fluid Mechanics. Dr. Armen Kocharian
Chapter 14 Lecture 1 Fluid Mechanics Dr. Armen Kocharian States of Matter Solid Has a definite volume and shape Liquid Has a definite volume but not a definite shape Gas unconfined Has neither a definite
More informationCHARACTERISTIC OF FLUIDS. A fluid is defined as a substance that deforms continuously when acted on by a shearing stress at any magnitude.
CHARACTERISTIC OF FLUIDS A fluid is defined as a substance that deforms continuously when acted on by a shearing stress at any magnitude. In a fluid at rest, normal stress is called pressure. 1 Dimensions,
More information10. The dimensional formula for c) 6% d) 7%
UNIT. One of the combinations from the fundamental phsical constants is hc G. The unit of this epression is a) kg b) m 3 c) s - d) m. If the error in the measurement of radius is %, then the error in the
More information( ) ( ) A i ˆj. What is the unit vector  that points in the direction of A? 1) The vector A is given by = ( 6.0m ) ˆ ( 8.0m ) Solution A D) 6 E) 6
A i ˆj. What is the unit vector  that points in the direction of A? 1) The vector A is given b ( 6.m ) ˆ ( 8.m ) A ˆ i ˆ ˆ j A ˆ i ˆ ˆ j C) A ˆ ( 1 ) ( i ˆ ˆ j) D) Aˆ.6 iˆ+.8 ˆj E) Aˆ.6 iˆ.8 ˆj A) (.6m
More informationFluid Mechanics. Forces on Fluid Elements. Fluid Elements - Definition:
Fluid Mechanics Chapter 2: Fluid Statics Lecture 3 Forces on Fluid Elements Fluid Elements - Definition: Fluid element can be defined as an infinitesimal region of the fluid continuum in isolation from
More informationSTATICS. Moments of Inertia VECTOR MECHANICS FOR ENGINEERS: Seventh Edition CHAPTER. Ferdinand P. Beer
00 The McGraw-Hill Companies, nc. All rights reserved. Seventh E CHAPTER VECTOR MECHANCS FOR ENGNEERS: 9 STATCS Ferdinand P. Beer E. Russell Johnston, Jr. Distributed Forces: Lecture Notes: J. Walt Oler
More informationy=1/4 x x=4y y=x 3 x=y 1/3 Example: 3.1 (1/2, 1/8) (1/2, 1/8) Find the area in the positive quadrant bounded by y = 1 x and y = x3
Eample: 3.1 Find the area in the positive quadrant bounded b 1 and 3 4 First find the points of intersection of the two curves: clearl the curves intersect at (, ) and at 1 4 3 1, 1 8 Select a strip at
More informationi.e. the conservation of mass, the conservation of linear momentum, the conservation of energy.
04/04/2017 LECTURE 33 Geometric Interpretation of Stream Function: In the last class, you came to know about the different types of boundary conditions that needs to be applied to solve the governing equations
More informationSTATICS. Moments of Inertia VECTOR MECHANICS FOR ENGINEERS: Ninth Edition CHAPTER. Ferdinand P. Beer E. Russell Johnston, Jr.
N E 9 Distributed CHAPTER VECTOR MECHANCS FOR ENGNEERS: STATCS Ferdinand P. Beer E. Russell Johnston, Jr. Lecture Notes: J. Walt Oler Teas Tech Universit Forces: Moments of nertia Contents ntroduction
More informationAll that begins... peace be upon you
All that begins... peace be upon you School of Mechanical Engineering Mechanics of Fluids & Engineering Computing SKMM 2313 Mechanics of Fluids 1 Pressure Distribution in a Fluid «An excerpt (mostly) from
More informationCONSERVATION OF ENERGY FOR ACONTINUUM
Chapter 6 CONSERVATION OF ENERGY FOR ACONTINUUM Figure 6.1: 6.1 Conservation of Energ In order to define conservation of energ, we will follow a derivation similar to those in previous chapters, using
More informationLECTURE NOTES - III. Prof. Dr. Atıl BULU
LECTURE NOTES - III «FLUID MECHANICS» Istanbul Technical University College of Civil Engineering Civil Engineering Department Hydraulics Division CHAPTER KINEMATICS OF FLUIDS.. FLUID IN MOTION Fluid motion
More informationstorage tank, or the hull of a ship at rest, is subjected to fluid pressure distributed over its surface.
Hydrostatic Forces on Submerged Plane Surfaces Hydrostatic forces mean forces exerted by fluid at rest. - A plate exposed to a liquid, such as a gate valve in a dam, the wall of a liquid storage tank,
More informationBuoyancy and Stability of Immersed and Floating Bodies
Buoyancy and Stability of Immersed and Floating Bodies 9. 12. 2016 Hyunse Yoon, Ph.D. Associate Research Scientist IIHR-Hydroscience & Engineering Review: Pressure Force on a Plane Surface The resultant
More informationPHY 5246: Theoretical Dynamics, Fall Assignment # 9, Solutions. y CM (θ = 0) = 2 ρ m
PHY 546: Theoretical Dnamics, Fall 5 Assignment # 9, Solutions Graded Problems Problem (.a) l l/ l/ CM θ x In order to find the equation of motion of the triangle, we need to write the Lagrangian, with
More informationME 101: Engineering Mechanics
ME 0: Engineering Mechanics Rajib Kumar Bhattacharja Department of Civil Engineering ndian nstitute of Technolog Guwahati M Block : Room No 005 : Tel: 8 www.iitg.ernet.in/rkbc Area Moments of nertia Parallel
More informationAE301 Aerodynamics I UNIT B: Theory of Aerodynamics
AE301 Aerodynamics I UNIT B: Theory of Aerodynamics ROAD MAP... B-1: Mathematics for Aerodynamics B-: Flow Field Representations B-3: Potential Flow Analysis B-4: Applications of Potential Flow Analysis
More informationChapter 4: Fluid Kinematics
Overview Fluid kinematics deals with the motion of fluids without considering the forces and moments which create the motion. Items discussed in this Chapter. Material derivative and its relationship to
More informationThe Bernoulli Equation
The Bernoulli Equation The most used and the most abused equation in fluid mechanics. Newton s Second Law: F = ma In general, most real flows are 3-D, unsteady (x, y, z, t; r,θ, z, t; etc) Let consider
More informationσ = F/A. (1.2) σ xy σ yy σ zx σ xz σ yz σ, (1.3) The use of the opposite convention should cause no problem because σ ij = σ ji.
Cambridge Universit Press 978-1-107-00452-8 - Metal Forming: Mechanics Metallurg, Fourth Edition Ecerpt 1 Stress Strain An understing of stress strain is essential for the analsis of metal forming operations.
More informationChapter 14. Fluid Mechanics
Chapter 14 Fluid Mechanics States of Matter Solid Has a definite volume and shape Liquid Has a definite volume but not a definite shape Gas unconfined Has neither a definite volume nor shape All of these
More informationFundamentals of Fluid Dynamics: Ideal Flow Theory & Basic Aerodynamics
Fundamentals of Fluid Dynamics: Ideal Flow Theory & Basic Aerodynamics Introductory Course on Multiphysics Modelling TOMASZ G. ZIELIŃSKI (after: D.J. ACHESON s Elementary Fluid Dynamics ) bluebox.ippt.pan.pl/
More informationWhere does Bernoulli's Equation come from?
Where does Bernoulli's Equation come from? Introduction By now, you have seen the following equation many times, using it to solve simple fluid problems. P ρ + v + gz = constant (along a streamline) This
More informationSurvey of Wave Types and Characteristics
Seminar: Vibrations and Structure-Borne Sound in Civil Engineering Theor and Applications Surve of Wave Tpes and Characteristics Xiuu Gao April 1 st, 2006 Abstract Mechanical waves are waves which propagate
More informationFLUID MECHANICS. Chapter 3 Elementary Fluid Dynamics - The Bernoulli Equation
FLUID MECHANICS Chapter 3 Elementary Fluid Dynamics - The Bernoulli Equation CHAP 3. ELEMENTARY FLUID DYNAMICS - THE BERNOULLI EQUATION CONTENTS 3. Newton s Second Law 3. F = ma along a Streamline 3.3
More informationTHE HEATED LAMINAR VERTICAL JET IN A LIQUID WITH POWER-LAW TEMPERATURE DEPENDENCE OF DENSITY. V. A. Sharifulin.
THE HEATED LAMINAR VERTICAL JET IN A LIQUID WITH POWER-LAW TEMPERATURE DEPENDENCE OF DENSITY 1. Introduction V. A. Sharifulin Perm State Technical Universit, Perm, Russia e-mail: sharifulin@perm.ru Water
More informationSEAKEEPING AND MANEUVERING Prof. Dr. S. Beji 2
SEAKEEPING AND MANEUVERING Prof. Dr. S. Beji 2 Ship Motions Ship motions in a seaway are very complicated but can be broken down into 6-degrees of freedom motions relative to 3 mutually perpendicular axes
More information2 4πε ( ) ( r θ. , symmetric about the x-axis, as shown in Figure What is the electric field E at the origin O?
p E( r, θ) = cosθ 3 ( sinθ ˆi + cosθ ˆj ) + sinθ cosθ ˆi + ( cos θ 1) ˆj r ( ) ( p = cosθ sinθ ˆi + cosθ ˆj + sinθ cosθ ˆi sinθ ˆj 3 r where the trigonometric identit ( θ ) vectors ˆr and cos 1 = sin θ
More informationWater Flow in Open Channels
The Islamic Universit of Gaza Facult of Engineering Civil Engineering Department Hdraulics - ECIV 33 Chapter 6 Water Flow in Open Channels Introduction An open channel is a duct in which the liquid flows
More informationPHY4116 From Newton to Einstein. Mid-Term Test, 10a.m. Wed. 16 th Nov Duration: 50 minutes. There are 25 marks in Section A and 25 in Section B.
PHY46 From Newton to Einstein Mid-Term Test, 0a.m. Wed. 6 th Nov. 06 Duration: 50 minutes. There are 5 marks in Section A and 5 in Section B. Use g = 0 ms in numerical calculations. You ma use the following
More informationFluid Mechanics (ME 201) 1
Fluid Mechanics (ME 201) 1 9 Forces on Submered Bodies 9.1 Net Force on a Submered Plane Surfaces In this section, we will compute the forces actin on a plane surface. We consider a surface oriented at
More informationHydrostatic. Pressure distribution in a static fluid and its effects on solid surfaces and on floating and submerged bodies.
Hydrostatic Pressure distribution in a static fluid and its effects on solid surfaces and on floating and submerged bodies. M. Bahrami ENSC 283 Spring 2009 1 Fluid at rest hydrostatic condition: when a
More informationMULTIPLE-CHOICE PROBLEMS:(Two marks per answer) (Circle the Letter Beside the Most Correct Answer in the Questions Below.)
MULTIPLE-CHOICE PROLEMS:(Two marks per answer) (Circle the Letter eside the Most Correct Answer in the Questions elow.) 1. The absolute viscosity µ of a fluid is primarily a function of: a. Density. b.
More informationChapter 10. Rotation of a Rigid Object about a Fixed Axis
Chapter 10 Rotation of a Rigid Object about a Fixed Axis Angular Position Axis of rotation is the center of the disc Choose a fixed reference line. Point P is at a fixed distance r from the origin. A small
More informationRotational Kinematics and Dynamics. UCVTS AIT Physics
Rotational Kinematics and Dynamics UCVTS AIT Physics Angular Position Axis of rotation is the center of the disc Choose a fixed reference line Point P is at a fixed distance r from the origin Angular Position,
More informationModule 2: Governing Equations and Hypersonic Relations
Module 2: Governing Equations and Hypersonic Relations Lecture -2: Mass Conservation Equation 2.1 The Differential Equation for mass conservation: Let consider an infinitely small elemental control volume
More informationGeometry and Motion of Isotropic Harmonic Oscillators (Ch. 9 and Ch. 11 of Unit 1)
Lecture Revised.. from..0 Geometr and Motion of Isotropic Harmonic Oscillators (Ch. and Ch. of Unit ) Geometr of idealized Sophomore-phsics Earth Coulomb field outside Isotropic Harmonic Oscillator (IHO)
More information2. Supports which resist forces in two directions. Fig Hinge. Rough Surface. Fig Rocker. Roller. Frictionless Surface
4. Structural Equilibrium 4.1 ntroduction n statics, it becomes convenient to ignore the small deformation and displacement. We pretend that the materials used are rigid, having the propert or infinite
More informationBasics Concepts and Ideas First Order Differential Equations. Dr. Omar R. Daoud
Basics Concepts and Ideas First Order Differential Equations Dr. Omar R. Daoud Differential Equations Man Phsical laws and relations appear mathematicall in the form of Differentia Equations The are one
More informationAPPLIED MECHANICS I Resultant of Concurrent Forces Consider a body acted upon by co-planar forces as shown in Fig 1.1(a).
PPLIED MECHNICS I 1. Introduction to Mechanics Mechanics is a science that describes and predicts the conditions of rest or motion of bodies under the action of forces. It is divided into three parts 1.
More informationMECHANICS OF MATERIALS REVIEW
MCHANICS OF MATRIALS RVIW Notation: - normal stress (psi or Pa) - shear stress (psi or Pa) - normal strain (in/in or m/m) - shearing strain (in/in or m/m) I - area moment of inertia (in 4 or m 4 ) J -
More informationChapter 13 TORSION OF THIN-WALLED BARS WHICH HAVE THE CROSS SECTIONS PREVENTED FROM WARPING (Prevented or non-uniform torsion)
Chapter 13 TORSION OF THIN-WALLED BARS WHICH HAVE THE CROSS SECTIONS PREVENTED FROM WARPING (Prevented or non-uniform torsion) 13.1 GENERALS In our previous chapter named Pure (uniform) Torsion, it was
More informationUNSTEADY LOW REYNOLDS NUMBER FLOW PAST TWO ROTATING CIRCULAR CYLINDERS BY A VORTEX METHOD
Proceedings of the 3rd ASME/JSME Joint Fluids Engineering Conference Jul 8-23, 999, San Francisco, California FEDSM99-8 UNSTEADY LOW REYNOLDS NUMBER FLOW PAST TWO ROTATING CIRCULAR CYLINDERS BY A VORTEX
More informationCHAPTER 3 Applications of Differentiation
CHAPTER Applications of Differentiation Section. Etrema on an Interval.............. 0 Section. Rolle s Theorem and the Mean Value Theorem. 07 Section. Increasing and Decreasing Functions and the First
More informationPHYSICS PART II SECTION- I. Straight objective Type
PHYSICS PAT II SECTION- I Straight objective Tpe This section contains 9 multiple choice questions numbered to 1. Each question has choices,, (C) and, out of which ONLY ONE is correct.. A parallel plate
More informationσ = F/A. (1.2) σ xy σ yy σ zy , (1.3) σ xz σ yz σ zz The use of the opposite convention should cause no problem because σ ij = σ ji.
Cambridge Universit Press 978-0-521-88121-0 - Metal Forming: Mechanics Metallurg, Third Edition Ecerpt 1 Stress Strain An understing of stress strain is essential for analzing metal forming operations.
More informationCONSERVATION LAWS AND CONSERVED QUANTITIES FOR LAMINAR RADIAL JETS WITH SWIRL
Mathematical and Computational Applications,Vol. 15, No. 4, pp. 742-761, 21. c Association for Scientific Research CONSERVATION LAWS AND CONSERVED QUANTITIES FOR LAMINAR RADIAL JETS WITH SWIRL R. Naz 1,
More informationFluid Mechanics for International Engineers HW #4: Conservation of Linear Momentum and Conservation of Energy
2141-365 Fluid Mechanics for International Engineers 1 Problem 1 RTT and Time Rate of Change of Linear Momentum and The Corresponding Eternal Force Notation: Here a material volume (MV) is referred to
More informationME 321: FLUID MECHANICS-I
6/07/08 ME 3: LUID MECHANI-I Dr. A.B.M. Toufique Hasan Professor Department of Mechanical Engineering Bangladesh Universit of Engineering & Technolog (BUET), Dhaka Lecture- 4/07/08 Momentum Principle teacher.buet.ac.bd/toufiquehasan/
More informationFluid Mechanics Discussion. Prepared By: Dr.Khalil M. Al-Astal Eng.Ahmed S. Al-Agha Eng.Ruba M. Awad
Discussion Prepared By: Dr.Khalil M. Al-Astal Eng.Ahmed S. Al-Agha Eng.Ruba M. Awad 2014-2015 Chapter (1) Fluids and their Properties Fluids and their Properties Fluids (Liquids or gases) which a substance
More informationUNIT II. Buoyancy and Kinematics of Fluid Motion
SIDDHARTH GROUP OF INSTITUTIONS :: PUTTUR Siddharth Nagar, Narayanavanam Road 517583 QUESTION BANK (DESCRIPTIVE) Subject with Code : FM(15A01305) Year & Sem: II-B.Tech & I-Sem Course & Branch: B.Tech -
More information3.8 The First Law of Thermodynamics and the Energy Equation
CEE 3310 Control Volume Analysis, Sep 30, 2011 65 Review Conservation of angular momentum 1-D form ( r F )ext = [ˆ ] ( r v)d + ( r v) out ṁ out ( r v) in ṁ in t CV 3.8 The First Law of Thermodynamics and
More informationGame Physics. Game and Media Technology Master Program - Utrecht University. Dr. Nicolas Pronost
Game and Media Technology Master Program - Utrecht University Dr. Nicolas Pronost Essential physics for game developers Introduction The primary issues Let s move virtual objects Kinematics: description
More informationLecture 15 Strain and stress in beams
Spring, 2019 ME 323 Mechanics of Materials Lecture 15 Strain and stress in beams Reading assignment: 6.1 6.2 News: Instructor: Prof. Marcial Gonzalez Last modified: 1/6/19 9:42:38 PM Beam theory (@ ME
More information2.6 Force reacts with planar object in fluid
2.6 Force reacts with planar object in fluid Fluid surface Specific weight (γ) => Object sinks in fluid => C is center of gravity or Centroid => P is center of pressure (always under C) => x axis is cross
More informationSteven Burian Civil & Environmental Engineering September 25, 2013
Fundamentals of Engineering (FE) Exam Mechanics Steven Burian Civil & Environmental Engineering September 25, 2013 s and FE Morning ( Mechanics) A. Flow measurement 7% of FE Morning B. properties Session
More informationAMME2261: Fluid Mechanics 1 Course Notes
Module 1 Introduction and Fluid Properties Introduction Matter can be one of two states: solid or fluid. A fluid is a substance that deforms continuously under the application of a shear stress, no matter
More information