Lead Type Disc Ceramic Capacitors (Safety Standard Certified) Resin Molding SMD Type Ceramic Capacitors (Safety Standard Certified)

Transcription

1 Type Disc Ceramic Capacitors (Safety Standard Certified) Resin Molding SMD Type Ceramic Capacitors (Safety Standard Certified)

2 EU RoHS Compliant All the products in this catalog comply with EU RoHS. EU RoHS is "the European Directive 0/65/EU on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment." For more details, please refer to our web page, "Murata's Approach for EU RoHS" ( compliance/rohs).

3 Contents Product specifications are as of 08. Part Numbering p Safety Standard Certified Resin Molding SMD Type Ceramic Capacitors for General Purpose Type EA (Reinforced Insulation) -Class X, Y- (Recommend) p5 Type EA and Test Methods p7 Type EA Complemant of Test Methods Type EA Packing p9 p0 Type EA!Caution p Type EA Notice p4 Safety Standard Certified Type Disc Ceramic Capacitors for General Purpose Type SA: AC400V (Basic Insulation) -Class X, Y- (Recommend) p5 4 Type RA: AC500V (Reinforced Insulation) -Class X, Y- (Recommend) p7 Type SA: AC400V / RA: AC500V and Test Methods p9 4 Type SA: AC50V or AC00V (Basic Insulation) -Class X, Y- (Recommend) p 5 Type RA: AC50V or AC00V (Reinforced Insulation) -Class X, Y- (Recommend) Type SA: AC50V or AC00V / RA: AC50V or AC00V and Test Methods p6 p9 5 6 Type RB (Reinforced Insulation) -Class X, Y- (Recommend) p Type RB: X: AC760V and Test Methods p5 7 8 Type KY (Basic Insulation) -Class X, Y- Type KX New Small Size (Reinforced Insulation) -Class X, Y- Type KY/KX and Test Methods p9 p4 p45 6 Characteristics Data (Typical Example) Packaging!Caution Notice p49 p5 p55 p58 7 Safety Standard Certified Type Disc Ceramic Capacitors for Automotive 9 Type KJ -Class X, Y- (For Automotive Use/AC Line Filter of PHEV/EV Charger) Type KJ and Test Methods p59 p60 8 Characteristics Data (Typical Example) Packaging!Caution Notice Type Disc Ceramic Capacitors (Safety Certified)/ Resin Molding SMD Type Ceramic Capacitors (Safety Certified) ISO9000 Certifications p64 p65 p66 p69 p70 9 Please check the MURATA website ( if you cannot find a part number in this catalog.

4 o Part Numbering Safety Standard Certified Resin Molding SMD Type Ceramic Capacitors for General Purpose (Part Number) DK E EA 0 M 86 R AH Product ID Series Category Product ID DK Code Outline Temperature Characteristics Code B E X Safety Standard Certified Temperature Characteristics B E SL Cap. or Temp. Coeff. Contents IEC ClassX, Y Temperature Range ±0% -5 to +85 C +0%, -55% +50 to -000ppm/ C +0 to +85 C 6 Tolerance Code K M 7Case Size Code 86 8Packaging Code R Tolerance ±0% ±0% Dimensions 8.0 x 6.0mm Packaging ø0mm Embossed Taping 4Rated Voltage/Safety Standard Certified Type Code EA Rated Voltage X: AC440V (r.m.s.), Y: AC50V (r.m.s.) or X: AC440V (r.m.s.), Y: AC00V (r.m.s.) (Safety Standard Certified Type EA) 9Individual Specification Code Expressed by four figures. 5 Expressed by three figures. The unit is pico-farad (pf). The first and second figures are significant digits, and the third figure expresses the number of zeros that follow the two numbers.

5 Safety Standard Certified Type Disc Ceramic Capacitors for General Purpose (Part Number) DE E KY M 6 N 7 A 8 9 F : Product ID Series Category 6 Tolerance Product Code Outline Contents ID Safety Standard IEC Class X, Y DE Certified IEC Class X, Y For Electrical Appliance and Material Safety Law of Japan, the first three digits (Product ID and Series Category) express "Series Name." For Safety Certified Capacitors, the first three digits express product code. The fourth figure expresses certified type shown in 4Safety Standard Certified Type column. Temperature Characteristics 4Rated Voltage/Safety Standard Certified Type Code RA RB KX SA KY Code B E F X Temperature Characteristics B E F SL Cap. or Temp. Coeff. Temperature Range ±0% +0%, -55% -5 to +85 C +0%, -80% +50 to -000ppm/ C +0 to +85 C Rated Voltage X: AC440V (r.m.s.), Y: AC50V (r.m.s.) or X: AC440V (r.m.s.), Y: AC00V (r.m.s.) or X: AC500V (r.m.s.), Y: AC500V (r.m.s.) (Safety Standard Certified Type RA) X: AC760V (r.m.s.), Y: AC500V (r.m.s.) (Safety Standard Certified Type RB) X: AC440V (r.m.s.), Y: AC50V (r.m.s.) or X: AC440V (r.m.s.), Y: AC00V (r.m.s.) (Safety Standard Certified Type KX) X: AC00V (r.m.s.), Y: AC50V (r.m.s.) or X: AC00V (r.m.s.), Y: AC00V (r.m.s.) or X: AC440V (r.m.s.), Y: AC400V (r.m.s.) (Safety Standard Certified Type SA) X: AC50V (r.m.s.), Y: AC50V (r.m.s.) or X: AC50V (r.m.s.), Y: AC00V (r.m.s.) (Safety Standard Certified Type KY) Code J K M 7 Style Code A A A4 B/J B/J B4/J4 N N N4 8Packaging Code A B Style Vertical Crimp Long Vertical Crimp Short Vertical Crimp Taping 9Individual Specification Code For part number that cannot be identified without "Individual Specification," it is added at the end of part number, expressed by three-digit alphanumerics. :Halogen-free Compatible Product Tolerance Spacing ±5% ±0% ±0% Dimensions (mm) Diameter ø0.6±0.05 ø0.6±0.05 ø0.6±0.05 Packaging Ammo Pack Taping Bulk Pitch of Components Expressed by three figures. The unit is pico-farad (pf). The first and second figures are significant digits, and the third figure expresses the number of zeros that follow the two numbers.

6 Safety Standard Certified Type Disc Ceramic Capacitors for Automotive (Part Number) DE 6 E KJ M 6 N 7 A 8 9 Product ID Series Category 7 Style Product ID DE The first three digits express product code. The fourth figure expresses certified type shown in 4Safety Standard Certified Type column. Temperature Characteristics Code B E 4Rated Voltage/Safety Standard Certified Type Code KJ Code 6 Outline Safety Standard Certified Contents Temperature Cap. Characteristics or Temp. Coeff. B E IEC Class X, Y ±0% +0%, -55% Rated Voltage Temperature Range -5 to +85 C X: AC440V (r.m.s.), Y: AC00V (r.m.s.) (Safety Standard Certified Type KJ) 5 Expressed by three figures. The unit is pico-farad (pf). The first and second figures are significant digits, and the third figure expresses the number of zeros that follow the two numbers. Code A B N 8Packaging Code A B Style Vertical Crimp Long Vertical Crimp Short Vertical Crimp Taping Spacing Dimensions (mm) Diameter 7.5 ø0.6±0.05 Packaging Ammo Pack Taping Bulk Pitch of Components 9Individual Specification Code For part number that cannot be identified without "Individual Specification," it is added at the end of part number, expressed by three-digit alphanumerics. 5 6 Tolerance Code K M Tolerance ±0% ±0% 4

7 Safety Standard Certified Resin Molding SMD Type Ceramic Capacitors for General Purpose Type EA (Reinforced Insulation) -Class X, Y SMD Type- (Recommend) Features. Small size and low height SMD. Operating temperature range guaranteed up to 5 C.. Dielectric strength: AC4000V 4. Class X/Y capacitors certified by ENEC (SEMKO)/UL/ CQC/KTC 5. Can be use with a component in appliances requiring reinforced insulation and double insulation based on UL49, IEC60065 and IEC Coated with flame-retardant halogen-free* epoxy resin (conforming to UL94V-0 standard). * Cl=900ppm max., Br=900ppm max. and Cl+Br=500ppm max. 7. Rated voltage: X: AC440V(r.m.s.), Y: AC50V(r.m.s.) or X: AC440V(r.m.s.), Y: AC00V(r.m.s.) W 0.75±0. 8.0±0.5 L.5±0. T (*0) (in mm) L:.4±0.5, W: 6.0±0.5, T:.5 max. The value marked with * is a reference. Applications Ideal for use as Y capacitors and primary-secondary coupling on the reduction in the size and thickness of power supply equipment. Do not use these products in any automotive power train or safety equipment including battery chargers for electric vehicles and plug-in hybrids. Only Murata products clearly stipulated as "for Automotive use" on its catalog can be used for automobile applications such as power train and safety equipment. Standard Certification Rated Voltage (50Vac) Standard No. ENEC (SEMKO) EN UL UL CQC IEC KTC KC Certified No. SE/6008- E79 CQC HU Rated Voltage 50Vac(r.m.s.) Marking Rated Voltage (50Vac) Example EA 0 X 440~ Y 50~ 5 5N Type Designation EA Nominal (Under 00pF: Actual value, 00pF and over: digit system) Company Name Code 5: Made in Thailand 4 Manufactured Date Code KTC Approval Mark Class Code XY Rated Voltage Mark 440~, 50~ Continued on the following page. 5

8 !Note Please read rating and!caution (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. Continued from the preceding page. Standard Certification Rated Voltage (00Vac) ENEC (SEMKO) UL CQC Standard No. EN UL IEC Certified No. SE/6008- E79 CQC Rated Voltage 00Vac(r.m.s.) Marking Rated Voltage (00Vac) Example Type Designation EA Nominal (Under 00pF: Actual value, 00pF and over: digit system) Company Name Code 5 5N 5: Made in Thailand 4 Manufactured Date Code Class Code XY Rated Voltage Mark 440~, 00~ EA 0 X 440~ Y 00~ Rated Voltage 50Vac Part Number AC Rated Voltage Temp. Dimension L Dimension W Body Thickness T DKXEA00K86RAH0 50Vac(r.m.s.) SL 0pF±0%.4±0.5mm 6.0±0.5mm.5mm max. DKXEA0K86RAH0 50Vac(r.m.s.) SL pf±0%.4±0.5mm 6.0±0.5mm.5mm max. DKXEA470K86RAH0 50Vac(r.m.s.) SL 47pF±0%.4±0.5mm 6.0±0.5mm.5mm max. DKBEA0K86RAH0 50Vac(r.m.s.) B 00pF±0%.4±0.5mm 6.0±0.5mm.5mm max. DKBEAK86RAH0 50Vac(r.m.s.) B 0pF±0%.4±0.5mm 6.0±0.5mm.5mm max. DKBEAK86RAH0 50Vac(r.m.s.) B 0pF±0%.4±0.5mm 6.0±0.5mm.5mm max. DKBEA47K86RAH0 50Vac(r.m.s.) B 470pF±0%.4±0.5mm 6.0±0.5mm.5mm max. DKBEA68K86RAH0 50Vac(r.m.s.) B 680pF±0%.4±0.5mm 6.0±0.5mm.5mm max. DKEEA0M86RAH0 50Vac(r.m.s.) E 000pF±0%.4±0.5mm 6.0±0.5mm.5mm max. DKEEA5M86RAH0 50Vac(r.m.s.) E 500pF±0%.4±0.5mm 6.0±0.5mm.5mm max. Murata part numbers might be changed. Therefore, please specify only the type name (EA) and capacitance of products in the part list when it is required for applying safety standard of electric equipments. Rated Voltage 00Vac Part Number AC Rated Voltage Temp. Dimension L Dimension W Body Thickness T DKXEA00K86RBH0 00Vac(r.m.s.) SL 0pF±0%.4±0.5mm 6.0±0.5mm.5mm max. DKXEA0K86RBH0 00Vac(r.m.s.) SL pf±0%.4±0.5mm 6.0±0.5mm.5mm max. DKXEA470K86RBH0 00Vac(r.m.s.) SL 47pF±0%.4±0.5mm 6.0±0.5mm.5mm max. DKBEA0K86RBH0 00Vac(r.m.s.) B 00pF±0%.4±0.5mm 6.0±0.5mm.5mm max. DKBEAK86RBH0 00Vac(r.m.s.) B 0pF±0%.4±0.5mm 6.0±0.5mm.5mm max. DKBEAK86RBH0 00Vac(r.m.s.) B 0pF±0%.4±0.5mm 6.0±0.5mm.5mm max. DKBEA47K86RBH0 00Vac(r.m.s.) B 470pF±0%.4±0.5mm 6.0±0.5mm.5mm max. DKBEA68K86RBH0 00Vac(r.m.s.) B 680pF±0%.4±0.5mm 6.0±0.5mm.5mm max. DKEEA0M86RBH0 00Vac(r.m.s.) E 000pF±0%.4±0.5mm 6.0±0.5mm.5mm max. DKEEA5M86RBH0 00Vac(r.m.s.) E 500pF±0%.4±0.5mm 6.0±0.5mm.5mm max. Murata part numbers might be changed. Therefore, please specify only the type name (EA) and capacitance of products in the part list when it is required for applying safety standard of electric equipments. 6 Continued on the following page.

9 Type EA and Test Methods Operating Temperature Range: -40 to +5 C No. Test Method No defects or abnormalities Dimensions Within specified dimension Dielectric Strength No defects or abnormalities 4 Insulation Resistance () 5 Within the specified tolerance 6 Dissipation Factor (D.F.) 0.05 max. 7 9 Solderability of Termination Temperature Characteristics 8 Vibration Resistance 0 Soldering Effect (Reflow) Adhesive strength of Termination D.F. 6000MΩ or more Temp. Coefficient SL: +50 to -000 ppm/ C (Temp. Range: +0 to +85 C) Cap. (Temp. Range: -5 to +85 C) Within the specified tolerance Pass the item No.6 75% of the terminations are to be soldered. s Within ±0% Dielectric Strength 000MΩ or more Pass the item No. No removal of the terminations or other defects should occur. Visual Inspection. Using calipers and micrometers. The capacitor shall not be damage when AC4000V(r.m.s.) is applied between the terminations for 60s. The insulation resistance shall be measured with DC500±50V within 60±5s of charging. The voltage should be applied to the capacitor through a resistor of MΩ. /D.F. shall be measured at 0 C with the frequency of ±0.kHz and a voltage of AC±0.V(r.m.s.). The capacitance measurement shall be made at each step in table. Perform the heat treatment at 50+0/-0 C for 60±5min and then let sit for 4±h at room condition*. Step Temp. ( C) 0± -5± 0± 4 85± Immerse the capacitor in the solution of ethanol (JIS K 80) and rosin (JIS K 590) (5% rosin in weight proportion). Immerse in solder solution for ±0.5s. Temp. of solder: 45±5 C Solder the capacitor to the Test Jig a (glass epoxy board) shown in "Complement of test method". Then apply 0N force in the direction of the arrow. 0N, 0±s 5 0± Solder the capacitor to the Test Jig a (glass epoxy board) shown in "Complement of test method". The capacitor shall be subjected to a simple harmonic motion having a total amplitude of.5mm, the frequency being varied uniformly between the approximate limits of 0 and 55Hz. The frequency range, from 0 to 55Hz and return to 0Hz, shall be traversed in approximately min. This motion shall be applied for a period of h in each of mutually perpendicular directions (total of 6h). Preheat the capacitor at 50 to 80 C for 90±0s. Reflow temp.: 0 C min. (max. temp.: 60 C) Reflow time: 0±0s. Reflow number of times: 4 times Let sit at room condition* for 4±h, then measure. of the sample has dropped to room temperature. Capacitor should be stored at 50+0/-0 C for h, and apply the AC4000V(r.m.s.) 60s then placed at room condition* for 4±h before initial measurements. Temperature Cycle D.F. Dielectric Strength Within ±5% SL: 0.05 max max. 000MΩ or more Pass the item No. * "Room condition" Temperature: 5 to 5 C, Relative humidity: 45 to 75%, Atmosphere pressure: 86 to 06kPa Fix the capacitor to the supporting Test Jig A (glass epoxy board) shown in "Complement of test method". Perform the 5 cycles according to the 4 heat treatments listed the following table. Step 4 Temp. ( C) -40± Room Temp. 5± Room Temp. Time (min.) 0± to 0± to Let sit for 4±h, at room condition*, then measure. Capacitor should be stored at 50+0/-0 C for h, and apply the AC4000V(r.m.s.) 60s then placed at room condition* for 4±h berore initial measurements. Continued on the following page. 7

10 Type EA and Test Methods Continued from the preceding page. No. Test Method Humidity (Steady state) 4 Humidity Loading 5 Life 6 Passive Flammability D.F. Dielectric Strength D.F. Dielectric Strength Dielectric Strength Within ±0% SL: 0.05 max. B, E: 0.05 max. 000MΩ or more Pass the item No. Within ±0% SL: 0.05 max. B, E: 0.05 max. 000MΩ or more Pass the item No. Within ±0% 000MΩ or more Pass the item No. The burning time should not exceeded the time 0s. The tissue paper should not ignite. Sit the capacitor at 40± C and relative humidity 90 to 95% for 500+4/-0h. Remove and let sit for 4±h at room condition*, then measure. Capacitor should be stored at 50+0/-0 C for h, and apply the AC4000V(r.m.s.) 60s then placed at room condition* for 4±h berore initial measurements. Apply the rated voltage at 40± C and relative humidity 90 to 95% for 500+4/-0h. Remove and let sit for 4±h at room condition*, then measure., E char. Capacitor should be stored at 50+0/-0 C for h, and apply the AC4000V(r.m.s.) 60s then placed at room condition* for 4±h berore initial measurements. Impulse Voltage test is performed. Each individual capacitor shall be subjected to a 8kV impulse (the voltage value means zero to peak) for times. Then the capacitors are applied to life test. 00 (%) T T T t Front time (T) =.μs=.67t Time to half-value (T) =50μs Apply voltage as Table for 000h at 5+/-0 C, relative humidity 50% max. Applied Voltage AC550V(r.m.s.), except that once each hour the voltage is increased to AC000V(r.m.s.) for 0.s. Remove and let sit for 4±h at room condition*, then measure. Capacitor should be stored at 50+0/-0 C for h, and apply the AC4000V(r.m.s.) 60s then placed at room condition* for 4±h berore initial measurements. The capacitor under test shall be held in the flame in the position which best promotes burning. Each specimen shall only be exposed once to the flame. Time of exposure to flame: 0s. Length of flame : ±mm Gas burner : Length 5mm min. Inside Dia. 0.5±0.mm Outside Dia. 0.9mm max. Gas : Butane gas Purity 95% min. Approximately 8mm Test Specimen burner flame 45 00±5mm Tissue Paper Wood board of approximately 0mm in thickness * "Room condition" Temperature: 5 to 5 C, Relative humidity: 45 to 75%, Atmosphere pressure: 86 to 06kPa Continued on the following page. 8

11 Type EA and Test Methods Continued from the preceding page. No. Test Method The capacitor shall be individually wrapped in at least one but more than two complete layers of cheesecloth. The capacitor shall be subjected to 0 discharges. The interval between successive discharges should be 5s. The UAC shall be maintained for min after the last discharge. S F L L R Tr S C UAC C L C L Cx Ct Ut 7 Active Flammability The cheesecloth should not be on fire. Oscilloscope C L Ct : R Ω Cx : Capacitor specimens UAC : UR F : UR : Rated Voltage Ut : Voltage impressed on the tank capacitor Ct Ux 5kV time Complement of Test Method Test Jig The test jig should be Jig A as described in and Test Methods. The specimen should be soldered by the conditions as described below. Soldering Method: Reflow soldering Solder: Sn-.0Ag-0.5Cu Test Jig A Solder resist Test Jig Copper foil (in mm) 9

12 Type EA Packing Packing. Dimension of Tape.0+/ /-0. ø.5+0./ /-0. B A.5+/ /-0. 4+/ /-0. A B (typ.) 4.0 max. (in mm). Dimension of Reel 9.4±.0.0±0.5 ø.0±0.8 80±.0 ø.0±0. 0±.0 5.4±.0 (in mm) () Part of the leader and part of the empty tape shall be attached to the end of the tape as follows. Vacant section: 60 min. Capacitor mounting unit Vacant section Direction of feed 90 min. 0 min. (in mm) () The top tape or cover tape and base tape are not attached at the end of the tape for a minimum of pitches. () Missing capacitors number within 0.% of the number per reel or pc, whichever is greater, and not continuous. (4) The top tape or cover tape and bottom tape shall not protrude beyond the edges of the tape and shall not cover sprocket holes. (5) Cumulative tolerance of sprocket holes, 0 pitches: ±0.mm. (6) Peeling off force: 0. to 0.6N in the direction shown on the follows. 65 to 80 Top Tape or Cover Tape Base Tape Minimum Quantity (Order in Sets Only) [Taping] (pcs./ammo Pack) Packing Qty Type EA,500 0

13 Type EA!Caution!Caution (Rating). Operating Voltage When DC-rated capacitors are to be used in AC or ripple current circuits, be sure to maintain the Vp-p value of the applied voltage or the Vo-p that contains DC bias within the rated voltage range. When the voltage is applied to the circuit, starting or stopping may generate irregular voltage for a transit period because of resonance or switching. Be sure to use a capacitor with a rated voltage range that includes these irregular voltages. Voltage DC Voltage DC+AC Voltage AC Voltage Pulse Voltage () Pulse Voltage () Positional Measurement V0-p V0-p Vp-p Vp-p Vp-p. Operating Temperature and Self-generated Heat (Apply to B/E/F ) Keep the surface temperature of a capacitor below the upper limit of its rated operating temperature range. Be sure to take into account the heat generated by the capacitor itself. When the capacitor is used in a highfrequency current, pulse current or similar current, it may have self-generated heat due to dielectric loss. Applied voltage load should be such that self-generated heat is within 0 C under the condition where the capacitor is subjected to an atmospheric temperature of 5 C. When measuring, use a thermocouple of small thermal capacity-k of ø0.mm under conditions where the capacitor is not affected by radiant heat from other components or wind from surroundings. Excessive heat may lead to deterioration of the capacitor's characteristics and reliability. (Never attempt to perform measurement with the cooling fan running. Otherwise, accurate measurement cannot be ensured.). Test Condition for Withstanding Voltage () Test Equipment Test equipment for AC withstanding voltage should be used with the performance of the wave similar to 50/60Hz sine wave. If the distorted sine wave or overload exceeding the specified voltage value is applied, a defect may be caused. Continued on the following page.

14 Type EA!Caution Continued from the preceding page. () Voltage Applied Method When the withstanding voltage is applied, the capacitor's lead or terminal should be firmly connected to the output of the withstanding voltage test equipment, and then the voltage should be raised from near zero to the test voltage. If the test voltage without the raise from near zero voltage would be applied directly to capacitor, test voltage should be applied with the zero cross.* At the end of the test time, the test voltage should be reduced to near zero, and then capacitor's lead or terminal should be taken off the output of the withstanding voltage test equipment. If the test voltage without the raise from near zero voltage would be applied directly to capacitor, the surge voltage may rise, and therefore, a defect may be caused. 0V Voltage sine wave zero cross *ZERO CROSS is the point where voltage sine wave passes 0V. See the figure at right. 4. Fail-Safe When the capacitor is broken, failure may result in a short circuit. Be sure to provide an appropriate fail-safe function like a fuse on your product if failure could result in an electric shock, fire or fuming. FAILURE TO FOLLOW THE ABOVE CAUTIONS MAY RESULT, WORST CASE, IN A SHORT CIRCUIT AND CAUSE FUMING OR PARTIAL DISPERSION WHEN THE PRODUCT IS USED.

15 Type EA!Caution!Caution (Storage and Operating Condition) Operating and Storage Environment The insulation coating of capacitors does not form a perfect seal; therefore, do not use or store capacitors in a corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the like are present. And avoid exposure to moisture. Before cleaning, bonding, or molding this product, verify that these processes do not affect product quality by testing the performance of a cleaned, bonded or molded product in the intended equipment. This one is MSL product. So, in order to avoid the absorption of moisture, capacitors are packed in moistureproof envelope. Store the capacitors in the following conditions at all times, and use within 6 months after delivered. Temperature: 0 to 0 C. Humidity: 60% max. Solder the enclosed capacitors within 68 hours after opening the moisture-proof package. After opening, store the capacitors in moisture-proof package with a desiccant and HIC card and keep the described condition. In case the storage period has been exceeded 6 months or the indicator color of a enclosed HIC card has changed when the package has been opened, perform baking (60 C x 68h) before soldering. FAILURE TO FOLLOW THE ABOVE CAUTIONS MAY RESULT, WORST CASE, IN A SHORT CIRCUIT AND CAUSE FUMING OR PARTIAL DISPERSION WHEN THE PRODUCT IS USED.!Caution (Soldering and Mounting). VIBRATION AND IMPACT Do not expose a capacitor or its leads to excessive shock or vibration during use.. SOLDERING () Reflow Soldering When soldering capacitor, it should be performed in following conditions. Soldering temperature: 0 to 60 C Soldering time: 0 to 0s. Preheating temperature: 70 C max. () Flow Soldering When soldering capacitor, it should be performed in following conditions. Soldering temperature: 60 C max. Soldering time: 5s max. Preheating temperature: 0 C max. Preheating time: 60s max. () Soldering Iron When soldering this product to a PCB/PWB, do not exceed the solder heat resistance specification of the capacitor. Subjecting this product to excessive heating could melt the internal junction solder and may result in thermal shocks that can crack the ceramic element. When soldering capacitor with a soldering iron, it should be performed in following conditions. Temperature of iron-tip: 400 C max. Soldering iron wattage: 50W max. Soldering time:.5s max.. BONDING, RESIN MOLDING AND COATING Before bonding, molding or coating this product, verify that these processes do not affect the quality of capacitor Standard Conditions for Reflow Soldering Temperature ( C) 60 C 0 C 70 C 50 C 0 C Preheating Soldering 60-0 s 0-0 s Gradual Cooling by testing the performance of the bonded, molded or coated product in the intended equipment. In case of the amount of applications, dryness / hardening conditions of adhesives and molding resins containing organic solvents (ethyl acetate, methyl ethyl ketone, toluene, etc.) are unsuitable, the outer coating resin of a capacitor is damaged by the organic solvents and it may result, worst case, in a short circuit. The variation in thickness of adhesive, molding resin or coating may cause a outer coating resin cracking and/or ceramic element cracking of a capacitor in a temperature cycling. FAILURE TO FOLLOW THE ABOVE CAUTIONS MAY RESULT, WORST CASE, IN A SHORT CIRCUIT AND CAUSE FUMING OR PARTIAL DISPERSION WHEN THE PRODUCT IS USED. Time

16 Type EA!Caution/Notice!Caution (Handling) VIBRATION AND IMPACT Do not expose a capacitor or its leads to excessive shock or vibration during use. FAILURE TO FOLLOW THE ABOVE CAUTIONS MAY RESULT, WORST CASE, IN A SHORT CIRCUIT AND CAUSE FUMING OR PARTIAL DISPERSION WHEN THE PRODUCT IS USED. Notice (Soldering and Mounting) CLEANING (ULTRASONIC CLEANING) To perform ultrasonic cleaning, observe the following conditions. Rinse bath capacity: Output of 0 watts per liter or less. Rinsing time: 5min maximum. Do not vibrate the PCB/PWB directly. Excessive ultrasonic cleaning may lead to fatigue destruction of the terminals. Notice (Rating). CAPACITANCE CHANGE OF CAPACITORS () Class capacitors might change a little depending on a surrounding temperature or an applied voltage. Please contact us if you use for the strict time constant circuit. () Class capacitors Class capacitors like temperature characteristic B, E and F have an aging characteristic, whereby the capacitor continually decreases its capacitance slightly if the capacitor leaves for a long time. Moreover, capacitance might change greatly depending on a surrounding temperature or an applied voltage. So, it is not likely to be able to use for the time constant circuit. Please contact us if you need a detail information.. PERFORMANCE CHECK BY EQUIPMENT Before using a capacitor, check that there is no problem in the equipment's performance and the specifications. Generally speaking, Class ceramic capacitors have voltage dependence characteristics and temperature dependence characteristics in capacitance. So, the capacitance value may change depending on the operating condition in a equipment. Therefore, be sure to confirm the apparatus performance of receiving influence in a capacitance value change of a capacitor, such as leakage current and noise suppression characteristic. Moreover, check the surge-proof ability of a capacitor in the equipment, if needed, because the surge voltage may exceed specific value by the inductance of the circuit. 4

17 Safety Standard Certified Type Disc Ceramic Capacitors for General Purpose Type SA: AC400V (Basic Insulation) -Class X, Y- (Recommend) Features. Impulse voltage guaranteed 8kV0-p.. Operating temperature range guaranteed up to 5 C.. Dielectric strength: AC600V 4. Class X/Y capacitors certified by ENEC(VDE)/UL/CQC. 5. Coated with flame-retardant halogen-free* epoxy resin (conforming to UL94V-0 standard). * Cl=900ppm max., Br=900ppm max. and Cl+Br=500ppm max. 6. Taping available for automatic insertion. 7. Rated Voltage: X: AC440V(r.m.s.), Y: AC400V(r.m.s.) [Bulk] Vertical Crimp Long (A) D max. e F±.0 T max. 5.0 min..0 max. ød (in mm) Code Coating Extension e ød A Up to the end of crimp 0.6±0.05 Applications D max. T max. Ideal for use as X/Y capacitors for AC line filters and primary-secondary coupling on switching power supplies and AC adapters. Do not use these products in any automotive power train or safety equipment including battery chargers for electric vehicles and plug-in hybrids. Only Murata products clearly stipulated as "for Automotive use" on its catalog can be used for automobile applications such as power train and safety equipment. [Bulk] Vertical Crimp Short (J) e F±0.8 Code J.5± Coating Extension e ød Up to the end of crimp.0 max. (in mm) ød 0.6±0.05 Standard Certification Marking ENEC (VDE) UL CQC Standard No. EN UL IEC Certified No E79 CQC Rated Voltage 400Vac(r.m.s.) 5 Example SA0M X 440~ Y 400~ 5D 5 4 Type Designation SA Nominal (Under 00pF: Actual value, 00pF and over: digit system) Tolerance 4 Company Name Code 5: Made in Thailand 5 Manufactured Date Code Class Code XY Rated Voltage Mark 440~, 400~ 5

18 Rated Voltage 400Vac Part Number AC Rated Voltage Temp. Body Dia. D Spacing F (mm) Body Thickness T Long Bulk Short Bulk DEXSA00KpppY0F 400Vac(r.m.s.) SL 0pF±0% 7.0mm max mm max. AB JB NA DEXSA50KpppY0F 400Vac(r.m.s.) SL 5pF±0% 6.0mm max mm max. AB JB NA DEXSA0KpppY0F 400Vac(r.m.s.) SL pf±0% 6.0mm max mm max. AB JB NA DEXSA0KpppY0F 400Vac(r.m.s.) SL pf±0% 7.0mm max mm max. AB JB NA DEXSA470KpppY0F 400Vac(r.m.s.) SL 47pF±0% 7.0mm max mm max. AB JB NA DEXSA680KpppY0F 400Vac(r.m.s.) SL 68pF±0% 9.0mm max mm max. AB JB NA DEBSA0KpppY0F 400Vac(r.m.s.) B 00pF±0% 6.0mm max mm max. AB JB NA DEBSA5KpppY0F 400Vac(r.m.s.) B 50pF±0% 6.0mm max mm max. AB JB NA DEBSAKpppY0F 400Vac(r.m.s.) B 0pF±0% 6.0mm max mm max. AB JB NA DEBSAKpppY0F 400Vac(r.m.s.) B 0pF±0% 6.0mm max mm max. AB JB NA DEBSA47KpppY0F 400Vac(r.m.s.) B 470pF±0% 7.0mm max mm max. AB JB NA DEBSA68KpppY0F 400Vac(r.m.s.) B 680pF±0% 8.0mm max mm max. AB JB NA DEESA0MpppY0F 400Vac(r.m.s.) E 000pF±0% 7.0mm max mm max. AB JB NA DEESA5MpppY0F 400Vac(r.m.s.) E 500pF±0% 8.0mm max mm max. AB JB NA DEESAMpppY0F 400Vac(r.m.s.) E 00pF±0% 9.0mm max mm max. AB JB NA DEESAMpppY0F 400Vac(r.m.s.) E 00pF±0%.0mm max mm max. AB JB NA DEESA47MpppY0F 400Vac(r.m.s.) E 4700pF±0%.0mm max mm max. AB JB NA DEESA0MpppY0F 400Vac(r.m.s.) E 0000pF±0% 7.0mm max mm max. AB JB N7A Taping Three blank columns are filled with the lead and packaging codes. Please refer to the columns on the right for the appropriate codes. Individual specification code "Y0F" express "simplicity marking and guarantee of dielectric strength between lead wires: AC600V." Murata part numbers might be changed depending on lead code or any other chagnes. Therefore, please specify only the type name (SA) and capacitance of products in the part list when it is required for applying safety standard of electric equipments. 6

19 Safety Standard Certified Type Disc Ceramic Capacitors for General Purpose Type RA: AC500V (Reinforced Insulation) -Class X, Y- (Recommend) Features D max. T max.. Impulse voltage guaranteed kv0-p.. Operating temperature range guaranteed up to 5 C.. Dielectric strength: AC4000V 4. Class X/Y capacitors certified by ENEC(VDE)/UL/CQC. 5. Can be use with a component in appliances requiring reinforced insulation and double insulation based on UL49, IEC60065 and IEC Coated with flame-retardant halogen-free* epoxy resin (conforming to UL94V-0 standard). * Cl=900ppm max., Br=900ppm max. and Cl+Br=500ppm max. 7. Taping available for automatic insertion. 8. Rated Voltage: X: AC500V(r.m.s.), Y: AC500V(r.m.s.) [Bulk] Vertical Crimp Long (A4) e F±.0 Code A4 5.0 min..0 max. ød (in mm) Coating Extension e ød Up to the end of crimp 0.6±0.05 D max. T max. Applications Ideal for use as X/Y capacitors for AC line filters and primary-secondary coupling on switching power supplies and AC adapters. e F±0.8.5± ød.0 max. Do not use these products in any automotive power train or safety equipment including battery chargers for electric vehicles and plug-in hybrids. Only Murata products clearly stipulated as "for Automotive use" on its catalog can be used for automobile applications such as power train and safety equipment. [Bulk] Vertical Crimp Short (J4) Code J4 Coating Extension e Up to the end of crimp (in mm) ød 0.6±0.05 Standard Certification Marking ENEC (VDE) UL CQC Standard No. EN UL IEC Certified No E79 CQC60085 Rated Voltage 500Vac(r.m.s.) 5 Example RA 47M X 500~ Y 500~ 5D 5 4 Type Designation RA Nominal (Under 00pF: Actual value, 00pF and over: digit system) Tolerance 4 Company Name Code 5: Made in Thailand 5 Manufactured Date Code Class Code XY Rated Voltage Mark 500~ 7

20 Rated Voltage 500Vac Part Number AC Rated Voltage Temp. Body Dia. D Spacing F (mm) Body Thickness T Long Bulk Short Bulk DEXRA00KpppQ0F 500Vac(r.m.s.) SL 0pF±0% 8.0mm max mm max. A4B J4B N4A DEXRA50KpppQ0F 500Vac(r.m.s.) SL 5pF±0% 6.0mm max mm max. A4B J4B N4A DEXRA0KpppQ0F 500Vac(r.m.s.) SL pf±0% 6.0mm max mm max. A4B J4B N4A DEXRA0KpppQ0F 500Vac(r.m.s.) SL pf±0% 7.0mm max mm max. A4B J4B N4A DEXRA470KpppQ0F 500Vac(r.m.s.) SL 47pF±0% 8.0mm max mm max. A4B J4B N4A DEXRA680KpppQ0F 500Vac(r.m.s.) SL 68pF±0% 9.0mm max mm max. A4B J4B N4A DEBRA0KpppQ0F 500Vac(r.m.s.) B 00pF±0% 6.0mm max mm max. A4B J4B N4A DEBRA5KpppQ0F 500Vac(r.m.s.) B 50pF±0% 8.0mm max mm max. A4B J4B N4A DEBRAKpppQ0F 500Vac(r.m.s.) B 0pF±0% 6.0mm max mm max. A4B J4B N4A DEBRAKpppQ0F 500Vac(r.m.s.) B 0pF±0% 7.0mm max mm max. A4B J4B N4A DEBRA47KpppQ0F 500Vac(r.m.s.) B 470pF±0% 8.0mm max mm max. A4B J4B N4A DEBRA68KpppQ0F 500Vac(r.m.s.) B 680pF±0% 9.0mm max mm max. A4B J4B N4A DEERA0MpppQ0F 500Vac(r.m.s.) E 000pF±0% 8.0mm max mm max. A4B J4B N4A DEERA5MpppQ0F 500Vac(r.m.s.) E 500pF±0% 9.0mm max mm max. A4B J4B N4A DEERAMpppQ0F 500Vac(r.m.s.) E 00pF±0%.0mm max mm max. A4B J4B N4A DEERAMpppQ0F 500Vac(r.m.s.) E 00pF±0%.0mm max mm max. A4B J4B N4A DEERA47MpppQ0F 500Vac(r.m.s.) E 4700pF±0% 4.0mm max mm max. A4B J4B N4A Taping Three blank columns are filled with the lead and packaging codes. Please refer to the columns on the right for the appropriate codes. Murata part numbers might be changed depending on lead code or any other chagnes. Therefore, please specify only the type name (RA) and capacitance of products in the part list when it is required for applying safety standard of electric equipments. 8

21 Type SA: AC400V / RA: AC500V and Test Methods Operating Temperature Range: -40 to +5 C No. Test Method and Dimensions No visible defect, and dimensions are within specified range. The capacitor should be visually inspected for evidence of defect. Dimensions should be measured with slide calipers. Marking To be easily legible Within specified tolerance 4 Dissipation Factor (D.F.).5% max. 5 Insulation Resistance () 0000MΩ min. The capacitor should be visually inspected. The capacitance, dissipation factor should be measured at 0 C with ±0.kHz and AC±0.V max. The insulation resistance should be measured with DC500±50V within 60±5s of charging. The voltage should be applied to the capacitor through a resistor of MΩ. The capacitor should not be damaged when the test voltages from Table are applied between the lead wires for 60s. Between Wires No failure Type SA RA <Table > Test Voltage AC600V(r.m.s.) 50/60Hz AC4000V(r.m.s.) 50/60Hz 6 Dielectric Strength Body Insulation No failure First, the terminals of the capacitor should be connected together. Then, as shown in the figure at right, a metal foil should be closely wrapped around the body of the capacitor to the distance of about to 4mm (in case of Type RA: to 6mm) from each terminal. Then, the capacitor should be inserted into a container filled with metal balls of about mm diameter. Finally, AC Metal Foil about to 4mm (in case of Type RA: to 6mm) Metal Balls voltage from Table is applied for 60s between the capacitor lead wires and metal balls. Type SA RA <Table > Test Voltage AC600V(r.m.s.) 50/60Hz AC4000V(r.m.s.) 50/60Hz 7 Temperature Characteristics B Within ±0% E Within 55% +0 (Temp. range: -5 to +85 C) Temperature Coefficient SL +50 to -000ppm/ C (Temp. range: +0 to +85 C) The capacitance measurement should be made at each step specified in Table. Step 4 5 <Table > Temperature (ºC) 0± -5± 0± 85± 0± 8 Solderability of s 9 Soldering Effect (Non-Preheat) Dielectric Strength wire should be soldered with uniform coating on the axial direction over /4 of the circumferential direction. Within ±0% 000MΩ min. Per 6 * "Room condition" Temperature: 5 to 5 C, Relative humidity: 45 to 75%, Atmosphere pressure: 86 to 06kPa The lead wire of a capacitor should be dipped into molten solder for ±0.5s. The depth of immersion is up to about.5 to.0mm from the root of lead wires. Temp. of solder: Free Solder (Sn-Ag-0.5Cu) 45±5 C Solder Temperature : 50±0 C or 60±5 C Immersion time :.5±0.5s (In case of 60±5 C : 0±s) The depth of immersion is up to about.5 to.0mm from the roof of lead wires. Heat Capacitor Shield.5 to.0mm Molten Solder Pre-treatment: Capacitor should be stored at 5± C for h, and apply the AC000V(r.m.s.) 60s (in case of Type RA, apply the AC4000V(r.m.s.) 60s) then placed at room condition* for 4±h before initial measurements. (Do not apply to SL char.) Post-treatment: Capacitor should be stored for to h at room condition*. Continued on the following page. 9

22 Type SA: AC400V / RA: AC500V and Test Methods Continued from the preceding page. No. Test Method 0 Soldering Effect (On-Preheat) Dielectric Strength Within ±0% 000MΩ min. Per 6 First the capacitor should be stored at 0+0/-5 C for 60+0/-5s. Then, as in the figure, the lead wires should be immersed in solder of 60+0/-5 C up to.5 to.0mm from the root of terminal for 7.5+0/-s. Pre-treatment: Heat Shield Capacitor.5 to.0mm Molten Solder Capacitor should be stored at 5± C for h, and apply the AC000V(r.m.s.) 60s (in case of Type RA, apply the AC4000V(r.m.s.) 60s) then placed at room condition* for 4±h before initial measurements. (Do not apply to SL char.) Post-treatment: Capacitor should be stored for to h at room condition*. Vibration Resistance D.F. Within the specified tolerance.5% max. The capacitor should be firmly soldered to the supporting lead wire and vibrated at a frequency range of 0 to 55Hz,.5mm in total amplitude, with about a -minute rate of vibration change from 0 to 55Hz and back to 0Hz. Apply for a total of 6h, h each in mutually perpendicular directions. Humidity (Under Steady State) D.F. B E SL B, E SL 000MΩ min. Within ±0% Within ±5% Within ± 5% D.F.< = 5.0% D.F.< =.5% Set the capacitor for 500±h at 40± C in 90 to 95% relative humidity. Pre-treatment: Capacitor should be stored at 5± C for h, and apply the AC000V(r.m.s.) 60s (in case of Type RA, apply the AC4000V(r.m.s.) 60s) then placed at room condition* for 4±h berore initial measurements. (Do not apply to SL char.) Post-treatment: Capacitor should be stored for to h at room condition*. Dielectric Strength Per 6 Humidity Loading D.F. Dielectric Strength B E SL B, E SL 000MΩ min. Per 6 Within ±0% Within ±5% Within ± 5% D.F.< = 5.0% D.F.< =.5% * "Room condition" Temperature: 5 to 5 C, Relative humidity: 45 to 75%, Atmosphere pressure: 86 to 06kPa Apply the AC440V (r.m.s.) (in case of Type RA: AC500V (r.m.s.)) for 500±h at 40± C in 90 to 95% relative humidity. Pre-treatment: Capacitor should be stored at 5± C for h, and apply the AC000V(r.m.s.) 60s (in case of Type RA, apply the AC4000V(r.m.s.) 60s) then placed at room condition* for 4±h berore initial measurements. (Do not apply to SL char.) Post-treatment: Capacitor should be stored for to h at room condition*. Continued on the following page. 0

23 Type SA: AC400V / RA: AC500V and Test Methods Continued from the preceding page. No. Test Method Within ±0% 000MΩ min. Impulse Voltage Each individual capacitor should be subjected to a 8kV (Type RA: kv) impulses for three times. Then the capacitors are applied to life test. 00 (%) Front time (T) =.μs=.67t Time to half-value (T) =50μs 0 0 T t T T Apply a voltage from Table 4 for 000h at 5+/-0 C, and relative humidity of 50% max. 4 Life Dielectric Strength Per 6 <Table 4> In Case of Type SA rated voltage: AC400V AC680V(r.m.s.) <50/60Hz> except that once each hour the voltage is increased to AC000V(r.m.s.) for 0. sec. In Case of Type RA rated voltage: AC500V AC850V(r.m.s.) <50/60Hz> except that once each hour the voltage is increased to AC000V(r.m.s.) for 0. sec. Pre-treatment: Capacitor should be stored at 5± C for h, and apply the AC000V(r.m.s.) 60s (in case of Type RA, apply the AC4000V(r.m.s.) 60s) then placed at room condition* for 4±h before initial measurements. (Do not apply to SL char.) Post-treatment: Capacitor should be stored for 4h at room condition*. 5 Robustness of Terminations Tensile Bending wire should not be cut off. Capacitor should not be broken. As shown in the figure at right, fix the body of the capacitor and apply a tensile weight gradually to each lead wire in the radial direction of the capacitor up to 0N and keep it for 0±s. Each lead wire should be subjected to 5N of weight and bent 90 at the point of egress, in one direction, then returned to its original position and bent 90 in the opposite direction at the rate of one bend in to s. W The capacitor should be individually wrapped in at least one but not more than two complete layers of cheesecloth. The capacitor should be subjected to 0 discharges. The interval between successive discharges should be 5s. The UAC should be maintained for min after the last discharge. S F L L R Tr S C UAC L C C L4 Cx Ct Ut 6 Active Flammability The cheesecloth should not be on fire. Oscilloscope C, : μf±0% C : 0.0μF±5% 0kV L to 4 :.5mH±0% 6A Rod core choke Ct : μf±5% 0kV R : 00Ω±% Cx : Capacitor under test UAC : UR±5% F : Fuse, Rated 0A UR : Rated Voltage Ut : Voltage applied to Ct Ux 5kV time * "Room condition" Temperature: 5 to 5 C, Relative humidity: 45 to 75%, Atmosphere pressure: 86 to 06kPa Continued on the following page.

24 Type SA: AC400V / RA: AC500V and Test Methods Continued from the preceding page. No. Test Method 7 Passive Flammability The burning time should not exceed 0s. The tissue paper should not ignite. The capacitor under test should be held in the flame in the position that best promotes burning. Each specimen should only be exposed once to the flame. Time of exposure to flame: 0s. Length of flame : ±mm Gas burner : Length 5mm min. Inside Dia. 0.5±0.mm Outside Dia. 0.9mm max. Gas : Butane gas Purity 95% min. About 8mm 45 00±5mm Test Specimen Tissue About 0mm Thick Board 8 Temperature and Immersion Cycle D.F. Dielectric Strength B E SL B, E SL 000MΩ min. Per 6 Within ±0% Within ±0% Within ± 5% D.F.< = 5.0% D.F.< =.5% The capacitor should be subjected to 5 temperature cycles, then consecutively to immersion cycles. Step 4 * "Room condition" Temperature: 5 to 5 C, Relative humidity: 45 to 75%, Atmosphere pressure: 86 to 06kPa Step <Temperature Cycle> Temperature (ºC) -40+0/- Room temp. 5+/-0 Room temp. <Immersion Cycle> Time Temperature (ºC) (min.) 65+5/-0 0± 5 5 Time (min.) 0 0 Cycle time: 500 cycles Immersion Water Clean water Salt water Cycle time: cycles Pre-treatment: Capacitor should be stored at 5±ºC for h, and apply the AC000V(r.m.s.) 60s (in case of Type RA, apply the AC4000V(r.m.s.) 60s) then placed at room condition* for 4±h. (Do not apply to SL char.) Post-treatment: Capacitor should be stored for 4±h at room condition*.

25 Safety Standard Certified Type Disc Ceramic Capacitors for General Purpose Type SA: AC50V or AC00V (Basic Insulation) -Class X, Y- (Recommend) Features D max. T max.. For some capacitance, reduced body size than current new "Type KY", reduced the diameter size ~mm.. Operating temperature range guaranteed up to 5 C.. Dielectric strength: AC000V (for lead spacing F=5mm) AC600V (for lead spacing F=7.5mm) 4. Class X/Y capacitors certified by ENEC(VDE)/UL/ CQC/KTC. 5. Coated with flame-retardant halogen-free* epoxy resin (conforming to UL94V-0 standard). * Cl=900ppm max., Br=900ppm max. and Cl+Br=500ppm max. 6. Taping available for automatic insertion. 7. Rated Voltage: X: AC00V(r.m.s.), Y: AC50V(r.m.s.) or X: AC00V(r.m.s.), Y: AC00V(r.m.s.) Applications Ideal for use as X/Y capacitors for AC line filters and primary-secondary coupling on switching power supplies and AC adapters. Do not use these products in any automotive power train or safety equipment including battery chargers for electric vehicles and plug-in hybrids. Only Murata products clearly stipulated as "for Automotive use" on its catalog can be used for automobile applications such as power train and safety equipment. [Bulk] Vertical Crimp Long (A, A) [Bulk] Vertical Crimp Short (J, J) e F±.0 Code 5.0 min. ød Coating Extension e A, A Up to the end of crimp e F±0.8 Code D max..5± T max. Coating Extension e J, J Up to the end of crimp ød.0 max. (in mm) ød 0.6± max. (in mm) ød 0.6± Standard Certification Rated Voltage (50Vac) ENEC (VDE) UL CQC KTC Standard No. EN UL IEC KC Certified No E79 CQC HU Rated Voltage 50Vac(r.m.s.) Marking Rated Voltage (50Vac) 5 Example SA0M X 00~ Y 50~ 5D 5 4 Type Designation SA Nominal (Under 00pF: Actual value, 00pF and over: digit system) Tolerance 4 Company Name Code 5: Made in Thailand 5 Manufactured Date Code Class Code XY Rated Voltage Mark 00~, 50~ Continued on the following page.

26 Continued from the preceding page. Standard Certification Rated Voltage (00Vac) ENEC (VDE) UL CQC Standard No. EN UL IEC Certified No E79 CQC Rated Voltage 00Vac(r.m.s.) Marking Rated Voltage (00Vac) 5 Example SA0M X 00~ Y 00~ 5D 5 4 Type Designation SA Nominal (Under 00pF: Actual value, 00pF and over: digit system) Tolerance 4 Company Name Code 5: Made in Thailand 5 Manufactured Date Code Class Code XY Rated Voltage Mark 00~ 4 Rated Voltage 50Vac Spacing F=7.5mm Part Number AC Rated Voltage Temp. Body Dia. D Spacing F (mm) Body Thickness T Long Bulk Short Bulk Taping DEXSA00KpppT0F 50Vac(r.m.s.) SL 0pF±0% 7.0mm max mm max. AB JB NA DEXSA50KpppT0F 50Vac(r.m.s.) SL 5pF±0% 6.0mm max mm max. AB JB NA DEXSA0KpppT0F 50Vac(r.m.s.) SL pf±0% 6.0mm max mm max. AB JB NA DEXSA0KpppT0F 50Vac(r.m.s.) SL pf±0% 7.0mm max mm max. AB JB NA DEXSA470KpppT0F 50Vac(r.m.s.) SL 47pF±0% 7.0mm max mm max. AB JB NA DEXSA680KpppT0F 50Vac(r.m.s.) SL 68pF±0% 8.0mm max mm max. AB JB NA DEBSA0KpppT0F 50Vac(r.m.s.) B 00pF±0% 6.0mm max mm max. AB JB NA DEBSA5KpppT0F 50Vac(r.m.s.) B 50pF±0% 6.0mm max mm max. AB JB NA DEBSAKpppT0F 50Vac(r.m.s.) B 0pF±0% 6.0mm max mm max. AB JB NA DEBSAKpppT0F 50Vac(r.m.s.) B 0pF±0% 6.0mm max mm max. AB JB NA DEBSA47KpppT0F 50Vac(r.m.s.) B 470pF±0% 7.0mm max mm max. AB JB NA DEBSA68KpppT0F 50Vac(r.m.s.) B 680pF±0% 7.0mm max mm max. AB JB NA DEESA0MpppT0F 50Vac(r.m.s.) E 000pF±0% 6.0mm max mm max. AB JB NA DEESA5MpppT0F 50Vac(r.m.s.) E 500pF±0% 7.0mm max mm max. AB JB NA DEESAMpppT0F 50Vac(r.m.s.) E 00pF±0% 8.0mm max mm max. AB JB NA DEESAMpppT0F 50Vac(r.m.s.) E 00pF±0% 9.0mm max mm max. AB JB NA DEESA47MpppT0F 50Vac(r.m.s.) E 4700pF±0% 0.0mm max mm max. AB JB NA DEESA0MpppT0F 50Vac(r.m.s.) E 0000pF±0% 5.0mm max mm max. AB JB N7A Three blank columns are filled with the lead and packaging codes. Please refer to the columns on the right for the appropriate codes. Individual specification code "T0F" express "simplicity marking and guarantee of dielectric strength between lead wires: AC600V." Murata part numbers might be changed depending on lead code or any other chagnes. Therefore, please specify only the type name (SA) and capacitance of products in the part list when it is required for applying safety standard of electric equipments. Continued on the following page. 4

27 Continued from the preceding page. Spacing F=5mm Part Number AC Rated Voltage Temp. Body Dia. D Spacing F (mm) Body Thickness T Long Bulk Short Bulk DEXSA00KpppT0F 50Vac(r.m.s.) SL 0pF±0% 7.0mm max mm max. AB JB NA DEXSA50KpppT0F 50Vac(r.m.s.) SL 5pF±0% 6.0mm max mm max. AB JB NA DEXSA0KpppT0F 50Vac(r.m.s.) SL pf±0% 6.0mm max mm max. AB JB NA DEXSA0KpppT0F 50Vac(r.m.s.) SL pf±0% 7.0mm max mm max. AB JB NA DEXSA470KpppT0F 50Vac(r.m.s.) SL 47pF±0% 7.0mm max mm max. AB JB NA DEXSA680KpppT0F 50Vac(r.m.s.) SL 68pF±0% 8.0mm max mm max. AB JB NA DEBSA0KpppT0F 50Vac(r.m.s.) B 00pF±0% 6.0mm max mm max. AB JB NA DEBSA5KpppT0F 50Vac(r.m.s.) B 50pF±0% 6.0mm max mm max. AB JB NA DEBSAKpppT0F 50Vac(r.m.s.) B 0pF±0% 6.0mm max mm max. AB JB NA DEBSAKpppT0F 50Vac(r.m.s.) B 0pF±0% 6.0mm max mm max. AB JB NA DEBSA47KpppT0F 50Vac(r.m.s.) B 470pF±0% 7.0mm max mm max. AB JB NA DEBSA68KpppT0F 50Vac(r.m.s.) B 680pF±0% 7.0mm max mm max. AB JB NA DEESA0MpppT0F 50Vac(r.m.s.) E 000pF±0% 6.0mm max mm max. AB JB NA DEESA5MpppT0F 50Vac(r.m.s.) E 500pF±0% 7.0mm max mm max. AB JB NA DEESAMpppT0F 50Vac(r.m.s.) E 00pF±0% 8.0mm max mm max. AB JB NA DEESAMpppT0F 50Vac(r.m.s.) E 00pF±0% 9.0mm max mm max. AB JB NA DEESA47MpppT0F 50Vac(r.m.s.) E 4700pF±0% 0.0mm max mm max. AB JB NA Taping Three blank columns are filled with the lead and packaging codes. Please refer to the columns on the right for the appropriate codes. Individual specification code "T0F" express "simplicity marking and guarantee of dielectric strength between lead wires: AC000V." Murata part numbers might be changed depending on lead code or any other chagnes. Therefore, please specify only the type name (SA) and capacitance of products in the part list when it is required for applying safety standard of electric equipments. 4 Rated Voltage 00Vac Spacing F=7.5mm Part Number AC Rated Voltage Temp. Body Dia. D Spacing F (mm) Body Thickness T Long Bulk Short Bulk DEXSA00KpppX0F 00Vac(r.m.s.) SL 0pF±0% 7.0mm max mm max. AB JB NA DEXSA50KpppX0F 00Vac(r.m.s.) SL 5pF±0% 6.0mm max mm max. AB JB NA DEXSA0KpppX0F 00Vac(r.m.s.) SL pf±0% 6.0mm max mm max. AB JB NA DEXSA0KpppX0F 00Vac(r.m.s.) SL pf±0% 7.0mm max mm max. AB JB NA DEXSA470KpppX0F 00Vac(r.m.s.) SL 47pF±0% 7.0mm max mm max. AB JB NA DEXSA680KpppX0F 00Vac(r.m.s.) SL 68pF±0% 8.0mm max mm max. AB JB NA DEBSA0KpppX0F 00Vac(r.m.s.) B 00pF±0% 6.0mm max mm max. AB JB NA DEBSA5KpppX0F 00Vac(r.m.s.) B 50pF±0% 6.0mm max mm max. AB JB NA DEBSAKpppX0F 00Vac(r.m.s.) B 0pF±0% 6.0mm max mm max. AB JB NA DEBSAKpppX0F 00Vac(r.m.s.) B 0pF±0% 6.0mm max mm max. AB JB NA DEBSA47KpppX0F 00Vac(r.m.s.) B 470pF±0% 7.0mm max mm max. AB JB NA DEBSA68KpppX0F 00Vac(r.m.s.) B 680pF±0% 7.0mm max mm max. AB JB NA DEESA0MpppX0F 00Vac(r.m.s.) E 000pF±0% 6.0mm max mm max. AB JB NA DEESA5MpppX0F 00Vac(r.m.s.) E 500pF±0% 7.0mm max mm max. AB JB NA DEESAMpppX0F 00Vac(r.m.s.) E 00pF±0% 8.0mm max mm max. AB JB NA DEESAMpppX0F 00Vac(r.m.s.) E 00pF±0% 9.0mm max mm max. AB JB NA DEESA47MpppX0F 00Vac(r.m.s.) E 4700pF±0% 0.0mm max mm max. AB JB NA DEESA0MpppX0F 00Vac(r.m.s.) E 0000pF±0% 5.0mm max mm max. AB JB N7A Three blank columns are filled with the lead and packaging codes. Please refer to the columns on the right for the appropriate codes. Individual specification code "X0F" express "simplicity marking and guarantee of dielectric strength between lead wires: AC600V." Murata part numbers might be changed depending on lead code or any other chagnes. Therefore, please specify only the type name (SA) and capacitance of products in the part list when it is required for applying safety standard of electric equipments. Taping 5