RIGHT ANGLE SURFACE MOUNT INFRARED PHOTOTRANSISTOR

Transcription

1 PACKAGE DIMENSIONS.16 (3.).11 (.8).43 (1.1).3 (.9) FRONT. (.).87 (.).71 (1.8).39 (1.).87 (.).71 (1.8) TOP.3 (.9) R.17 (.4) COLLECTOR MARK 1 NOTE:.16 (.4) BACK 1. Emitter. Collector 3. Tolerance of ±.1 (.) on all non nominal dimensions unless otherwise specified. 4. Dimensions for all drawings are in inches (mm). SCHEMATIC COLLECTOR 1 EMITTER DESCRIPTION is a phototransistor in miniature SMD package molded in a water clear plastic with right angle lens. FEATURES NPN Silicon Phototransistor Right Angle Surface Mount Package Matched Emitters: QTLP61CIR Available in.31 (8mm) width tape on 7 (178mm) diameter reel;, units per reel High Photo Sensitivity Low Junction Capacitance Fast Response Time Water Clear Lens Page 1 of 6

2 ABSOLUTE MAXIMUM RATINGS (T A = C unless otherwise specified) Parameter Symbol Rating Unit Operating Temperature T OPR - to +8 C Storage Temperature T STG -4 to +9 C Soldering Temperature (Iron) (,3,4) T SOL-I 4 for sec C Soldering Temperature (Flow) (,3) T SOL-F 6 for 1 sec C Collector Emitter Voltage V CE 3 V Emitter Collector Voltage V EC V Power Dissipation (1) P D 7 mw Notes: 1. At C or below.. RMA flux is recommended. 3. Methanol or isopropyl alcohols are recommended as cleaning agents. 4. Pulse conditions: tp = 1µs, T = 1 ms. ELECTRICAL / OPTICAL CHARACTERISTICS (T A = C) PARAMETER TEST CONDITIONS (λ P = 94nm) SYMBOL MIN. TYP. MAX. UNITS Peak Sensitivity Wavelength λps 86 nm Reception Angle Θ ±8 Deg. Dark Current V CE = V, Ee = I D 1 na Collector-Emitter Breakdown I C = 1µA, Ee = BV CEO 3 V Emitter-Collector Breakdown I E = 1µA, Ee = BV ECO V On-State Collector Current Ee = 1 mw/cm V CE = V I C(ON).1. ma Saturation Voltage Ee = 1 mw/cm I C = ma V CE(SAT).4 V Rise Time V CE = V, RL = 1Ω t r 1 µs Fall Time I C = 1mA t f 1 µs Page of 6

3 TYPICAL PERFORMANCE CURVES Fig. 1 Collector Power Dissipation vs. Ambient Temperature Fig. Collector Dark Current vs. Ambient Temperature Collector Power Dissipation PC (mw) Ambient Temperature T A ( C) Collector Dark Current (A) Ambient Temperature T A ( C) Fig. 3 Relative Collector Current vs. Ambient Temperature Fig. 4 Collector Current vs. Irradiance 1. Fig. Spectral Sensitivity Relative Spectral Sensitivity Relative Collector Current (%) V CE = V Ee=1 mw/cm Ambient Temperature T A ( C) 3. Fig. 6 Collector Current vs. Collector-Emitter Voltage Collector Current IC (ma) Collector Current IC (ma) V CE = V Ta = C Irradiance Ee (mw/cm ) 3 H=.mW/cm. H=1.mW/cm 1. 1 H=1.mW/cm. H=.mW/cm Wavelength λ (nm) Collector-Emitter Voltage VCE (V) Page 3 of 6

4 RECOMMENDED PRINTED CIRCUIT BOARD PATTERN.3 (.9).3 (.9).8 (.).8 (.).9 (1.) Light Emitting Direction.9 (1.).3 (.9).3 (.9).79 (.).79 (.).197 (.).197 (.) Mounting Example RECOMMENDED IR REFLOW SOLDERING PROFILE Classification Reflow Profile (JEDEC J-STD-C) 3 Temperature ( C) C Preheat 6 18s Ramp-up 3 C/sec max. 6 1s Ramp-down 6 C/sec max. 6 C 1 3s 48s max 1 1 Time (sec) Page 4 of 6

5 TAPE AND REEL DIMENSIONS.± Ø18±1 Ø6.±..±. Ø Progressive direction 1.7.±. 4. Ø1..±.3±.1 3.± Emitter Collector Dimensional tolerance is ±.1mm unless otherwise specified Angle: ±. Unit: mm Page of 6

6 EMITTING DIODE DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user.. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Page 6 of 6