PINNING - TO220AC PIN CONFIGURATION SYMBOL. tab

Transcription

1 BY GENERAL DESCRIPTION QUICK REFERENCE DATA Glass-passivated double diffused SYMBOL PARAMETER MAX. UNIT rectifier diode in a plastic envelope featuring low forward voltage drop, V RRM Repetitive peak reverse voltage 15 V fast reverse recovery and soft V F Forward voltage 1.5 V recovery characteristic. The device is I F(AV) Average forward current A intended for use in TV receivers, I FSM Non-repetitive peak forward current 6 A series resonant switched mode t rr Reverse recovery.6 µs power supplies and other high voltage circuits. PINNING - TO2AC PIN CONFIGURATION SYMBOL PIN DESCRIPTION 1 cathode (k) 2 anode (a) tab a k tab cathode (k) 1 2 LIMITING VALUES Limiting values in accordance with the Absolute Maximum System (IEC 134). SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT V RSM Non-repetitive peak reverse voltage - 15 V V RRM Repetitive peak reverse voltage - 15 V V RWM Crest working reverse voltage - 13 V I F(AV) Average forward current 1 sinusoidal; a = 1.57; T mb 1 C - A I F(RMS) RMS forward current A I FRM Repetitive peak forward current sinusoidal; a = A I FSM Non-repetitive peak forward t = ms - 6 A current t = 8.3 ms - 66 A sinusoidal; T j = 15 C prior to surge; with reapplied V RWM() I 2 t I 2 t for fusing t = ms - 18 A 2 s T stg T j Storage temperature Operating junction temperature C C THERMAL RESISTANCES R th j-mb Thermal resistance junction to K/W mounting base R th j-a Thermal resistance junction to in free air K/W ambient 1 Neglecting switching and reverse current losses. October Rev 1.

2 BY STATIC CHARACTERISTICS T j = 25 C unless otherwise stated V F Forward voltage I F = A V I F = A; T j = 15 C V I R Reverse current V R = 13 V - µa V R = 13 V; T j = C µa DYNAMIC CHARACTERISTICS T j = 25 C unless otherwise stated t rr Reverse recovery I F = 2 A; V R 3 V; -di F /dt = A/µs µs Q s Reverse recovery charge I F = 2 A; V R 3 V; -di F /dt = A/µs µc V fr Peak forward recovery voltage I F = A; di F /dt = 3 A/µs V I F di F dt trr PF / W Vo = 1.16 V Rs =.34 Ohms.1.2 BY359.5 Tmb() / C 9 D = I R Qs 25% I rrm Fig.1. Definition of t rr, Q s and I rrm % D = T T t IF(AV) / A Fig.3. Maximum forward dissipation P F = f(i F(AV) ); square wave where I F(AV) =I F(RMS) x D. I I F PF / W BY359X Tmb() / C Vo = 1.16 V Rs =.34 ohms a = V F 13 V fr Fig.2. Definition of V fr V F IF(AV) / A Fig.4. Maximum forward dissipation P F = f(i F(AV) ); sinusoidal current waveform where a = form factor = I F(RMS) / I F(AV). October Rev 1.

3 BY IFS(RMS) / A IFSM BY Qs / uc IF = A 5A 2A 1A 3 1ms ms.1s 1s s / s Fig.5. Maximum non-repetitive rms forward current. I F = f(t p ); sinusoidal current waveform; T j = 15 C prior to surge with reapplied V RWM dif/dt (A/us) Fig.8. Maximum reverse recovery charge Q s = f(di F /dt); parameter T j 3 IF / A Tj=15C Zth j-mb / (K/W) Tj=25C 1 typ.1 P D VF / V Fig.6. Typical and imum forward characteristic I F = f(v F ); parameter T j.1 us us 1ms ms.1s 1s s / s Fig.9. Transient thermal impedance Z th = f(t p ) t trr / us 1. IF = A 5A 2A 1A dif/dt (A/us) Fig.7. Maximum reverse recovery t rr = f(di F /dt); parameter T j October Rev 1.

4 BY MECHANICAL DATA Dimensions in mm Net Mass: 2 g 4,5,3 3,7 1,3 2,8 5,9 min 3, not tinned 15,8 3, 13,5 min 1,3 (2x) 1 2 5,8,9 (2x),6 2,4 Fig.. TO2AC; pin 1 connected to mounting base. Notes 1. Accessories supplied on request: refer to mounting instructions for TO2 envelopes. 2. Epoxy meets UL94 V at 1/8". October Rev 1.

5 BY DEFINITIONS Data sheet status Objective specification Preliminary specification Limiting values This data sheet contains target or goal specifications for product development. This data sheet contains preliminary data; supplementary data may be published later. This data sheet contains final product specifications. Limiting values are given in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of this specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. Philips Electronics N.V All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, it is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent or other industrial or intellectual property rights. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. October Rev 1.