Pure Substance. Properties of Pure Substances & Equations of State. Vapour-Liquid-Solid Phase Equilibrium
|
|
- Sophia Richard
- 6 years ago
- Views:
Transcription
1 Pure Substance Properties of Pure Substances & Equations of State Dr. d. Zahurul Haq Professor Department of echanical Engineering Bangladesh University of Engineering & Technology (BUET) Dhaka-1000, Bangladesh E 201: Basic Thermodynamics A pure substance is one that has a homogeneous and invariable chemical composition. It may exist in more than one phase, but the chemical composition is the same in all phases. Liquid water, a mixture of liquid water and water vapour (steam), and a mixture of ice and liquid water are all pure substances; every phase has the same chemical composition. A mixture of liquid air and gaseous air is not a pure substance as the composition of the liquid phase is different from that of the vapour phase. Sometimes a mixture of gases, such as air, is considered a pure substance as long as there is no change of phase. Strictly speaking, this is not true. Dr. d. Zahurul Haq (BUET) EOS E 201 (2013) 1 / 19 c Vapour-Liquid-Solid Phase Equilibrium T357 T358 T359 T360 T361 1 Compressed (P > P sat (T)) or subcooled liquid (T < T sat (P)). 2 Saturated liquid (T = T sat (P)). 3 Saturated liquid-vapour mixture (T = T sat (P)). 4 Saturated vapour (T = T sat (P)). 5 Superheated vapour (T > T sat (P)). c Dr. d. Zahurul Haq (BUET) EOS E 201 (2013) 2 / 19 Saturation temperature, T sat is the temperature at which vaporization takes place at a given pressure. This pressure is called the saturation pressure, P sat for the given temperature. If a substance exists as liquid at T sat and P sat is called a saturated liquid. If the temperature of the liquid is lower than the saturation temperature for the existing pressure, it is called either a sub-cooled liquid (implying T < T sat (P) or a compressed liquid (implying P > P sat (P)). When a substance exists as part liquid and part vapour at the saturation temperature, its quality, x is defined as the ratio of the mass of vapour to the total mass. If a substance exists as vapour at T sat, it is called saturated vapour. When the vapour is at T > T sat, it is said to exist as superheated vapour. c Dr. d. Zahurul Haq (BUET) EOS E 201 (2013) 3 / 19 c Dr. d. Zahurul Haq (BUET) EOS E 201 (2013) 4 / 19
2 T089 T048 T362 Temperature-Pressure diagram for water Critical Point Triple Point T c [ o C] P c [Pa] T [ o C] P [kpa] H 2 O CO O H c Dr. d. Zahurul Haq (BUET) EOS E 201 (2013) 5 / 19 c Dr. d. Zahurul Haq (BUET) EOS E 201 (2013) 6 / 19 Phase Equilibrium: Gibb s Phase Rule T096 x = mv m f +m g v = v f + x(v fg ) = v f + x(v g v f ) x quality m f mass of liquid m g mass of vapour c Dr. d. Zahurul Haq (BUET) EOS E 201 (2013) 7 / 19 Gibb s Phase Rule The number of degrees of freedom within a heterogeneous mixture of pure substances is given by Gibb s phase rule as f C P f = C P + 2 number of degrees of freedom number of components (pure substances) in the mixture number of phases A homogeneous (P = 1) pure substance (C =1) requires f = = 2 intensive properties to fix its state. A homogeneous (P = 1) mixture of two pure substances (C = 2) requires f = = 3 intensive properties to fix its state. A two-phase (P = 2) pure substance (C = 1) f = = 1: Each phase requires one intensive property to fix its state & one intensive property can be varied independently. c Dr. d. Zahurul Haq (BUET) EOS E 201 (2013) 8 / 19
3 c T017 P-T phase diagram is composed of three unique curves: 1 Fusion line region of 2-phase solid-liquid equilibrium, 2 Vaporization line region of 2-phase liquid-vapour equilibrium, 3 Sublimation line region of 2-phase solid-vapour equilibrium. These three lines intersect at one point, called the triple point, which is the only point where all three phases can be in equilibrium Dr. d. Zahurul Haq (BUET) simultaneously. EOS E 201 (2013) 9 / 19 T090 P-v-T diagram for a substance that expands on freezing (e.g. water) c Dr. d. Zahurul Haq (BUET) EOS E 201 (2013) 10 / 19 T018 At triple point of a pure substance, C = 1, P = 3, and the number of degrees of freedom are f = = 0; i.e., there is no flexibility in the thermodynamic state & none of the properties can be varied & still keep the system at the triple point. At critical point, the densities of the liquid & the vapour phases become equal and, consequently, where the physical interface between the liquid & the vapour disappears. c Dr. d. Zahurul Haq (BUET) EOS E 201 (2013) 11 / 19 T092 P-v-T diagram for a substance that contracts on freezing (e.g. CO 2 ) c Dr. d. Zahurul Haq (BUET) EOS E 201 (2013) 12 / 19
4 Equations of State (EOS) For simple compressible substances, any intensive property is solely a function of two other independent intensive properties. Equations of State (EOS) have the following form: Ideal-gas EOS: PV = mrt Pv = f(p,v,t) = 0 PV = nr u T [ ] Ru T = RT P = ρrt T046 Expands on freezing (e.g. H 2 O) T047 Contracts on freezing (e.g. CO 2 ) c Dr. d. Zahurul Haq (BUET) EOS E 201 (2013) 13 / 19 van der Waals Equation v b a v 2 b = account for the volume occupied by gas molecules a = account for intermolecular forces of attraction. P pressure [kpa] V volume [m 3 ] T temperature [K] R u universal gas constant, kj/kmol.k R specific gas constant, [kj/kg.k] molecular weight [kg/kmol] c Dr. d. Zahurul Haq (BUET) EOS E 201 (2013) 14 / 19 Generalized Compressibility Chart Departure from ideal gas Z Pv RT, for ideal gas, Z = 1 Reduced properties, P R P P c & T R T T c At critical point: ( ) ( P v T = 2 P v )T = 0 2 = v c = 3b, a = 27 R 2 Tc 2 64 P c, b = RTc 8P c Z c = Pcvc RT c = 3 8 = c T097 Dr. d. Zahurul Haq (BUET) EOS E 201 (2013) 15 / 19 T094 c Dr. d. Zahurul Haq (BUET) EOS E 201 (2013) 16 / 19
5 Example: Sp. volume of Water at 20.0 Pa & 520 o C Ideal Gas Law: R = Ru v ideal = RT P = 8314/18 = J/kg-K = (461.89)( ) = m 3 /kg Compressibility Chart: P R = = 0.905, T R = = 1.23 From chart: Z = v = Zv ideal = (0.83)(0.183) = m 3 /kg Tabulated value, based on experimental data: v = m 3 /kg Other Equations of State Viral Equation Redlich-Kwong Equation Z = Pv RT = 1+ B v + C v 2 + D v 3 + v b a = R2 Tc 2.5 P c Beattie-Bridgeman Equation a v(v + b) T b = RT c P c v 2 (1 e)(v + B) A v 2 ( ) ( ) where, A = A 0 1 a v, B = B0 1 b v, e = c vt 3 c Dr. d. Zahurul Haq (BUET) EOS E 201 (2013) 17 / 19 c Dr. d. Zahurul Haq (BUET) EOS E 201 (2013) 18 / 19 Estimate pressure exerted by 3.7 kg CO in a m 3 container at 215 K 1 Using ideal gas law: = = 28 kg/kmol. R = Ru P = mrt V = 8314/28= J/kg-K = (3kg)( J kg )(215K) Nm 0.03 m 3 J 1bar = 78.7 bar N m 2 2 Using van der Waals Eq.: P = 66.9 bar. given, a = bar.m 6 /kmol 2 & b = m 3 /kmol 3 Using Redlich-Kwong Eq.: P = 69.2 bar. given, a = bar.m 6.K 1/2 /kmol 2 & b = m 3 /kmol 4 NIST Table P = bar. c Dr. d. Zahurul Haq (BUET) EOS E 201 (2013) 19 / 19
Pure Substance. Properties of Pure Substances & Equations of State. Vapour-Liquid-Solid Phase Equilibrium
Pure Substance Properties of Pure Substances & Equations of State Dr. d. Zahurul Haq Professor Department of echanical Engineering Bangladesh University of Engineering & Technology (BUET) Dhaka-1000, Bangladesh
More informationChapter 3 PROPERTIES OF PURE SUBSTANCES
Thermodynamics: An Engineering Approach Seventh Edition Yunus A. Cengel, Michael A. Boles McGraw-Hill, 2011 Chapter 3 PROPERTIES OF PURE SUBSTANCES Copyright The McGraw-Hill Companies, Inc. Permission
More informationChapter 3 PROPERTIES OF PURE SUBSTANCES
Thermodynamics: An Engineering Approach Seventh Edition in SI Units Yunus A. Cengel, Michael A. Boles McGraw-Hill, 2011 Chapter 3 PROPERTIES OF PURE SUBSTANCES Copyright The McGraw-Hill Companies, Inc.
More informationPROPERTIES OF PURE SUBSTANCES. Chapter 3. Mehmet Kanoglu. Thermodynamics: An Engineering Approach, 6 th Edition. Yunus A. Cengel, Michael A.
Thermodynamics: An Engineering Approach, 6 th Edition Yunus A. Cengel, Michael A. Boles McGraw-Hill, 2008 Chapter 3 PROPERTIES OF PURE SUBSTANCES Mehmet Kanoglu Copyright The McGraw-Hill Companies, Inc.
More informationChapter 3 PROPERTIES OF PURE SUBSTANCES
Chapter 3 PROPERTIES OF PURE SUBSTANCES PURE SUBSTANCE Pure substance: A substance that has a fixed chemical composition throughout. Air is a mixture of several gases, but it is considered to be a pure
More informationChapter 3 PROPERTIES OF PURE SUBSTANCES SUMMARY
Chapter 3 PROPERTIES OF PURE SUBSTANCES SUMMARY PURE SUBSTANCE Pure substance: A substance that has a fixed chemical composition throughout. Compressed liquid (sub-cooled liquid): A substance that it is
More informationChapter 3 PROPERTIES OF PURE SUBSTANCES. Thermodynamics: An Engineering Approach, 6 th Edition Yunus A. Cengel, Michael A. Boles McGraw-Hill, 2008
Chapter 3 PROPERTIES OF PURE SUBSTANCES Thermodynamics: An Engineering Approach, 6 th Edition Yunus A. Cengel, Michael A. Boles McGraw-Hill, 2008 Objectives Introduce the concept of a pure substance. Discuss
More informationThermodynamics I. Properties of Pure Substances
Thermodynamics I Properties of Pure Substances Dr.-Eng. Zayed Al-Hamamre 1 Content Pure substance Phases of a pure substance Phase-change processes of pure substances o Compressed liquid, Saturated liquid,
More informationBasic Thermodynamics Module 1
Basic Thermodynamics Module 1 Lecture 9: Thermodynamic Properties of Fluids Thermodynamic Properties of fluids Most useful properties: Properties like pressure, volume and temperature which can be measured
More informationCHAPTER. Properties of Pure Substances
CHAPTER 2 Properties of Pure Substances A Pure Substance Is a substance that is chemically homogenous and fixed in chemical composition.(e.g. water, nitrogen, air & etc.) mixture of oil and water is not
More informationEvaluating properties of pure substances
Evaluating properties of pure substances Pure substance A pure substance has the same chemical composition throughout. Are the following confined in a fixed volume pure substances: Ice (single component,
More informationThermodynamics I Chapter 2 Properties of Pure Substances
Thermodynamics I Chapter 2 Properties of Pure Substances Mohsin Mohd Sies Fakulti Kejuruteraan Mekanikal, Universiti Teknologi Malaysia Properties of Pure Substances (Motivation) To quantify the changes
More informationPhase Diagrams. Department of Mechanical Engineering Indian Institute of Technology Kanpur Kanpur India
Phase Diagrams 1 Increasing the temperature isobarically T-v diagram of constant-pressure phase-change processes of a pure substance at various pressures numerical values are for water. 2 Temperature -
More informationwater Plays dominant role in radiation All three phases emit and absorb in longwave radiation
4.,4. water Plays dominant role in radiation All three phases emit and absorb in longwave radiation Some shortwave (solar) radiation is absorbed by all phases of water Principal role in the shortwave radiation
More informationEVALUATING PROPERTIES FOR A PURE SUBSTANCES. By Ertanto Vetra
EVALUATING PROPERTIES FOR A PURE SUBSTANCES 1 By Ertanto Vetra Outlines - TV, PV, PT, PVT Diagram - Property Tables - Introduction to Enthalpy - Reference State & Reference Values - Ideal Gas Equation
More informationPure Substance Properties and Equation of State
Pure Substance Properties and Equation of State Pure Substance Content Pure Substance A substance that has a fixed chemical composition throughout is called a pure substance. Water, nitrogen, helium, and
More informationConsequences of Second Law of Thermodynamics. Entropy. Clausius Inequity
onsequences of Second Law of hermodynamics Dr. Md. Zahurul Haq Professor Department of Mechanical Engineering Bangladesh University of Engineering & echnology BUE Dhaka-000, Bangladesh zahurul@me.buet.ac.bd
More informationc Dr. Md. Zahurul Haq (BUET) Thermodynamic Processes & Efficiency ME 6101 (2017) 2 / 25 T145 = Q + W cv + i h 2 = h (V2 1 V 2 2)
Thermodynamic Processes & Isentropic Efficiency Dr. Md. Zahurul Haq Professor Department of Mechanical Engineering Bangladesh University of Engineering & Technology (BUET Dhaka-1000, Bangladesh zahurul@me.buet.ac.bd
More informationMAHALAKSHMI ENGINEERING COLLEGE
MAHALAKSHMI ENGINEERING COLLEGE TIRUCHIRAPALLI 621 213. Department: Mechanical Subject Code: ME2202 Semester: III Subject Name: ENGG. THERMODYNAMICS UNIT-I Basic Concept and First Law 1. What do you understand
More informationConsequences of Second Law of Thermodynamics. Entropy. Clausius Inequity
onsequences of Second Law of hermodynamics Dr. Md. Zahurul Haq Professor Department of Mechanical Engineering Bangladesh University of Engineering & echnology BUE Dhaka-000, Bangladesh zahurul@me.buet.ac.bd
More informationT718. c Dr. Md. Zahurul Haq (BUET) HX: Energy Balance and LMTD ME 307 (2018) 2/ 21 T793
HX: Energy Balance and LMTD Dr. Md. Zahurul Haq Professor Department of Mechanical Engineering Bangladesh University of Engineering & Technology (BUET) Dhaka-000, Bangladesh http://zahurul.buet.ac.bd/
More information1. Heterogeneous Systems and Chemical Equilibrium
1. Heterogeneous Systems and Chemical Equilibrium The preceding section involved only single phase systems. For it to be in thermodynamic equilibrium, a homogeneous system must be in thermal equilibrium
More informationc Dr. Md. Zahurul Haq (BUET) Entropy ME 203 (2017) 2 / 27 T037
onsequences of Second Law of hermodynamics Dr. Md. Zahurul Haq Professor Department of Mechanical Engineering Bangladesh University of Engineering & echnology BUE Dhaka-000, Bangladesh zahurul@me.buet.ac.bd
More informationV i = component volume of component i. T282. c Dr. Md. Zahurul Haq (BUET) Gas Mixture ME 203 (2017) 6 / 22. Moist Air T284
Ideal Gas ixtures Properties of Homogeeous ixtures & Pyschrometry Dr. d. Zahurul Haq Professor Departmet of echaical Egieerig Bagladesh Uiversity of Egieerig & Techology (BUET) Dhaka-000, Bagladesh zahurul@me.buet.ac.bd
More informationChapter 12 PROPERTY RELATIONS. Department of Mechanical Engineering
Chapter 12 THERMODYNAMIC PROPERTY RELATIONS Dr Ali Jawarneh Department of Mechanical Engineering Hashemite University it Objectives Develop fundamental relations between commonly encountered thermodynamic
More informationIndex to Tables in SI Units
Index to Tables in SI Units Table A-1 Atomic or Molecular Weights and Critical Properties of Selected Elements and Compounds 926 Table A-2 Properties of Saturated Water (Liquid Vapor): Temperature Table
More informationGAS. Outline. Experiments. Device for in-class thought experiments to prove 1 st law. First law of thermodynamics Closed systems (no mass flow)
Outline First law of thermodynamics Closed systems (no mass flow) Device for in-class thought experiments to prove 1 st law Rubber stops GAS Features: Quasi-equlibrium expansion/compression Constant volume
More informationThermodynamics I Spring 1432/1433H (2011/2012H) Saturday, Wednesday 8:00am - 10:00am & Monday 8:00am - 9:00am MEP 261 Class ZA
Thermodynamics I Spring 1432/1433H (2011/2012H) Saturday, Wednesday 8:00am - 10:00am & Monday 8:00am - 9:00am MEP 261 Class ZA Dr. Walid A. Aissa Associate Professor, Mech. Engg. Dept. Faculty of Engineering
More informationME 201 Thermodynamics
Spring 01 ME 01 Thermodynamics Property Evaluation Practice Problems II Solutions 1. Air at 100 K and 1 MPa goes to MPa isenthapically. Determine the entropy change. Substance Type: Ideal Gas (air) Process:
More informationESO201A: Thermodynamics
ESO201A: Thermodynamics First Semester 2015-2016 Mid-Semester Examination Instructor: Sameer Khandekar Time: 120 mins Marks: 250 Solve sub-parts of a question serially. Question #1 (60 marks): One kmol
More informationUpon successful completion of this unit, the students should be able to:
Unit 9. Liquids and Solids - ANSWERS Upon successful completion of this unit, the students should be able to: 9.1 List the various intermolecular attractions in liquids and solids (dipole-dipole, London
More informationFuel, Air, and Combustion Thermodynamics
Chapter 3 Fuel, Air, and Combustion Thermodynamics 3.1) What is the molecular weight, enthalpy (kj/kg), and entropy (kj/kg K) of a gas mixture at P = 1000 kpa and T = 500 K, if the mixture contains the
More informationME6301- ENGINEERING THERMODYNAMICS UNIT I BASIC CONCEPT AND FIRST LAW PART-A
ME6301- ENGINEERING THERMODYNAMICS UNIT I BASIC CONCEPT AND FIRST LAW PART-A 1. What is meant by thermodynamics system? (A/M 2006) Thermodynamics system is defined as any space or matter or group of matter
More informationTHERMODYNAMICS, FLUID AND PLANT PROCESSES. The tutorials are drawn from other subjects so the solutions are identified by the appropriate tutorial.
THERMODYNAMICS, FLUID AND PLANT PROCESSES The tutorials are drawn from other subjects so the solutions are identified by the appropriate tutorial. THERMODYNAMICS TUTORIAL 1 LIQUIDS VAPOURS - GASES SAE
More informationChemical Engineering Thermodynamics
Chemical Engineering Thermodynamics P Liquid P x 1 sat P 1 T sat T 2 T x 1 T x 1 T y 1 Liquid Vapour sat P 2 P x 1 P y 1 P y 1 Vapour sat T 1 x, y 1 1 x, y 1 1 Pradeep Ahuja Contents CHEMICAL ENGINEERING
More informationME 201 Thermodynamics
8 ME 0 Thermodynamics Practice Problems or Property Evaluation For each process described below provide the temperature, pressure, and speciic volume at each state and the change in enthalpy, internal
More informationT098. c Dr. Md. Zahurul Haq (BUET) First Law of Thermodynamics ME 201 (2012) 2 / 26
Conservation of Energy for a Closed System Dr. Md. Zahurul Haq Professor Department of Mechanical Engineering Bangladesh University of Engineering & Technology (BUET Dhaka-, Bangladesh zahurul@me.buet.ac.bd
More informationCHAPTER 7 ENTROPY. Copyright Hany A. Al-Ansary and S. I. Abdel-Khalik (2014) 1
CHAPTER 7 ENTROPY S. I. Abdel-Khalik (2014) 1 ENTROPY The Clausius Inequality The Clausius inequality states that for for all cycles, reversible or irreversible, engines or refrigerators: For internally-reversible
More informationR13. II B. Tech I Semester Regular Examinations, Jan THERMODYNAMICS (Com. to ME, AE, AME) PART- A
SET - 1 II B. Tech I Semester Regular Examinations, Jan - 2015 THERMODYNAMICS (Com. to ME, AE, AME) Time: 3 hours Max. Marks: 70 Note 1. Question Paper consists of two parts (Part-A and Part-B) 2. Answer
More informationME 2322 Thermodynamics I PRE-LECTURE Lesson 10 Complete the items below Name:
Lesson 10 1. (5 pt) If P > P sat (T), the phase is a subcooled liquid. 2. (5 pt) if P < P sat (T), the phase is superheated vapor. 3. (5 pt) if T > T sat (P), the phase is superheated vapor. 4. (5 pt)
More informationEng Thermodynamics I conservation of mass; 2. conservation of energy (1st Law of Thermodynamics); and 3. the 2nd Law of Thermodynamics.
Eng3901 - Thermodynamics I 1 1 Introduction 1.1 Thermodynamics Thermodynamics is the study of the relationships between heat transfer, work interactions, kinetic and potential energies, and the properties
More informationCHEMISTRY Topic #2: Thermochemistry and Electrochemistry What Makes Reactions Go? Fall 2018 Dr. Susan Findlay See Exercises in Topic 8
CHEMISTRY 2000 Topic #2: Thermochemistry and Electrochemistry What Makes Reactions Go? Fall 208 Dr. Susan Findlay See Exercises in Topic 8 Vapour Pressure of Pure Substances When you leave wet dishes on
More informationMARIA COLLEGE OF ENGINEERING AND TECHNOLOGY
MARIA COLLEGE OF ENGINEERING AND TECHNOLOGY ATTOOR ENGINEERING THERMODYNAMICS (TWO MARK QUESTION BANK) UNIT 1 (BASIC COMCEPTS AND FIRST LAW) 1. Define the term thermal engineering. Thermal engineering
More informationq = m. C p. T q = heat (Joules) m = mass (g) C p = specific heat (J/g.o C) T = change in temp. ( o C) UNIT 11 - SOLIDS, LIQUIDS, & PHASE CHANGES
HEAT ENERGY NOTES UNIT 11 - SOLIDS, LIQUIDS, & PHASE CHANGES SECTION (A): same temp or change? SECTION (B): same temp or change? temp is called the energy difference at same temp = SECTION (C): same temp
More informationThermodynamic Properties
Thermodynamic Properties (TP) Thermodynamic Properties Define and articulate some of the critical language and concepts of Thermodynamics Distinguish between the universe, system, surroundings, and boundary
More informationDuncan. Q = m. C p. T. Q = heat (Joules) m = mass (g) C p = specific heat capacity (J/g.o C) T = change in temp. ( o C)
HEAT ENERGY NOTES SECTION (A): phase(s) of matter = SECTION (B): phase(s) of matter = energy difference at same temp = temp is called the SECTION (C): phase(s) of matter = SECTION (D): phase(s) of matter
More informationBasic Thermodynamics Prof. S. K. Som Department of Mechanical Engineering Indian Institute of Technology, Kharagpur. Lecture No 16
Basic Thermodynamics Prof. S. K. Som Department of Mechanical Engineering Indian Institute of Technology, Kharagpur Lecture No 16 Properties of Pure Substances-I Good afternoon. In the last class, we were
More informationFig Note the three different types of systems based on the type of boundary between system and surroundings.
CHAPTER 1 LECTURE NOTES System, Surroundings, and States Fig. 1.4 Note the three different types of systems based on the type of boundary between system and surroundings. Intensive and Extensive Properties
More informationName Date Class THE NATURE OF GASES
13.1 THE NATURE OF GASES Section Review Objectives Describe the assumptions of the kinetic theory as it applies to gases Interpret gas pressure in terms of kinetic theory Define the relationship between
More informationChapter 11 Gases 1 Copyright McGraw-Hill 2009
Chapter 11 Gases Copyright McGraw-Hill 2009 1 11.1 Properties of Gases The properties of a gas are almost independent of its identity. (Gas molecules behave as if no other molecules are present.) Compressible
More information5.60 Thermodynamics & Kinetics Spring 2008
MIT OpenCourseWare http://ocw.mit.edu 5.60 Thermodynamics & Kinetics Spring 2008 For information about citing these materials or our Terms of Use, visit: http://ocw.mit.edu/terms. 5.60 Spring 2008 Lecture
More informationMME 2010 METALLURGICAL THERMODYNAMICS II. Fundamentals of Thermodynamics for Systems of Constant Composition
MME 2010 METALLURGICAL THERMODYNAMICS II Fundamentals of Thermodynamics for Systems of Constant Composition Thermodynamics addresses two types of problems: 1- Computation of energy difference between two
More informationEquations of State. Equations of State (EoS)
Equations of State (EoS) Equations of State From molecular considerations, identify which intermolecular interactions are significant (including estimating relative strengths of dipole moments, polarizability,
More informationCHEMISTRY - TRO 4E CH.11 - LIQUIDS, SOLIDS & INTERMOLECULAR FORCES
!! www.clutchprep.com CONCEPT: INTERMOLECULAR FORCES When looking at a molecular substance such as H 2 O you will discover two types of electrostatic forces at work: forces exist within a molecule and
More informationQUIZZES RIEPJCPIγPJEJJJY
Che 3021 Thermodynamics I QUIZZES RIEPJCPIγPJEJJJY QUIZ 1. Find Molecular Weights: 1 1 CO 2 2 NaCl 3 Aspirin C 9 H 8 O 4 CO2 = NaCl = C9H8O4 = PIgPJC Quiz 1. Temperature conversion 1 Convert 94 o F, to
More informationName: Self Assessment - Preparatory
Name: Self Assessment - Preparatory 1. I have read the chapter before coming to the discussion session today. 2. I am able to state that a system is simply a space or mass that I choose to study. 3. I
More informationThe physical state of a substance can be changed by increasing or decreasing its temperature.
Chemistry Lecture #63: Changes of State The physical state of a substance can be changed by increasing or decreasing its temperature. For example, a solid substance can be converted into a liquid by heating
More informationUBMCC11 - THERMODYNAMICS. B.E (Marine Engineering) B 16 BASIC CONCEPTS AND FIRST LAW PART- A
UBMCC11 - THERMODYNAMICS B.E (Marine Engineering) B 16 UNIT I BASIC CONCEPTS AND FIRST LAW PART- A 1. What do you understand by pure substance? 2. Define thermodynamic system. 3. Name the different types
More informationGases. Characteristics of Gases. Unlike liquids and solids, gases
Gases Characteristics of Gases Unlike liquids and solids, gases expand to fill their containers; are highly compressible; have extremely low densities. 1 Pressure Pressure is the amount of force applied
More informationMAE 110A. Homework 3: Solutions 10/20/2017
MAE 110A Homework 3: Solutions 10/20/2017 3.10: For H 2O, determine the specified property at the indicated state. Locate the state on a sketch of the T-v diagram. Given a) T 140 C, v 0.5 m 3 kg b) p 30MPa,
More informationChapter 6 The States of Matter. Examples of Physical Properties of Three States of Matter
Chapter 6 The States of Matter Examples of Physical Properties of Three States of Matter 1 Three States of Matter Solids: Fixed shape, fixed volume, particles are held rigidly in place. Liquids: Variable
More informationThe Clausius-Clapeyron and the Kelvin Equations
PhD Environmental Fluid Mechanics Physics of the Atmosphere University of Trieste International Center for Theoretical Physics The Clausius-Clapeyron and the Kelvin Equations by Dario B. Giaiotti and Fulvio
More informationChapter 4. Energy Analysis of Closed Systems
Chapter 4 Energy Analysis of Closed Systems The first law of thermodynamics is an expression of the conservation of energy principle. Energy can cross the boundaries of a closed system in the form of heat
More informationFundamentals of Thermodynamics SI Version
Solution Manual Chapter 2 Fundamentals of hermodynamics SI Version Borgnakke Sonntag 8e Updated July 2013 2 Borgnakke and Sonntag CONEN CHAPER 2 SUBSECION PROB NO. Concept problems 1-15 Phase diagrams,
More informationPhases of matter and phase diagrams
Phases of matter and phase diagrams Transition to Supercritical CO2 Water Ice Vapor Pressure and Boiling Point Liquids boil when the external pressure equals the vapor pressure. Temperature of boiling
More informationDEPARTMENT OF MECHANICAL ENGINEERING ME6301-ENGINEERING THERMODYNAMICS
SYED AMMAL ENGINEERING COLLEGE (Approved by the AICTE, New Delhi, Govt. of Tamilnadu and Affiliated to Anna University, chennai) Established in 1998 - An ISO 9001:2008 Certified Institution Dr. E.M.Abdullah
More information12. Heat of melting and evaporation of water
VS 12. Heat of melting and evaporation of water 12.1 Introduction The change of the physical state of a substance in general requires the absorption or release of heat. In this case, one speaks of a first
More informationCHEMISTRY. Chapter 11 Intermolecular Forces Liquids and Solids
CHEMISTRY The Central Science 8 th Edition Chapter 11 Liquids and Solids Kozet YAPSAKLI States of Matter difference between states of matter is the distance between particles. In the solid and liquid states
More informationChemical Principles by Steven Zumdahl (5 e )
Chemical Principles by Steven Zumdahl (5 e ) 1 Chapter 1 Chemistry The Science of Change Chemistry is the study of the composition of matter, its chemical and physical properties, the chemical and physical
More informationClass XI Chapter 5 States of Matter Chemistry
Question 5.1: What will be the minimum pressure required to compress 500 dm 3 of air at 1 bar to 200 dm 3 at 30 C? Initial pressure, p 1 = 1 bar Initial volume, V 1 = 500 dm 3 Final volume, V 2 = 200 dm
More informationis more suitable for a quantitative description of the deviation from ideal gas behaviour.
Real and ideal gases (1) Gases which obey gas laws or ideal gas equation ( PV nrt ) at all temperatures and pressures are called ideal or perfect gases. Almost all gases deviate from the ideal behaviour
More informationChemistry B11 Chapter 6 Gases, Liquids, and Solids
Chapter 6 Gases, Liquids, and Solids States of matter: the physical state of matter depends on a balance between the kinetic energy of particles, which tends to keep them apart, and the attractive forces
More informationEDEXCEL NATIONAL CERTIFICATE/DIPLOMA SCIENCE FOR TECHNICIANS OUTCOME 3 - ENERGY TUTORIAL 2 HEAT
EDEXCEL NATIONAL CERTIFICATE/DIPLOMA SCIENCE FOR TECHNICIANS OUTCOME 3 - ENERGY TUTORIAL 2 HEAT 3. Energy Mechanical work, energy and power: work - energy relationship, gravitational potential energy,
More informationName Date Class STATES OF MATTER
13 STATES OF MATTER Chapter Test A A. Matching Match each description in Column B with the correct term in Column A. Write the letter of the correct description on the line. Column A Column B 1. amorphous
More informationCopyright 2018 Dan Dill 1
TP CO 2 gas at 1 atm, 0 is heated to 1 atm, 60 ; then compressed to 75 atm, 60 ; then cooled to 75 atm, 0 ; then expanded to 73 atm, 0. 1. gas 2. supercritical fluid 3. liquid 4. solid Lecture CH2 A2 (MWF
More informationLecture Presentation. Chapter 10. Gases. James F. Kirby Quinnipiac University Hamden, CT Pearson Education, Inc.
Lecture Presentation Chapter 10 James F. Kirby Quinnipiac University Hamden, CT Characteristics of Physical properties of gases are all similar. Composed mainly of nonmetallic elements with simple formulas
More informationTemperature and Its Measurement
Temperature and Its Measurement When the physical properties are no longer changing, the objects are said to be in thermal equilibrium. Two or more objects in thermal equilibrium have the same temperature.
More informationThermodynamics of solids 5. Unary systems. Kwangheon Park Kyung Hee University Department of Nuclear Engineering
Thermodynamics of solids 5. Unary systems Kwangheon ark Kyung Hee University Department of Nuclear Engineering 5.1. Unary heterogeneous system definition Unary system: one component system. Unary heterogeneous
More informationStates of matter Part 2
Physical Pharmacy Lecture 2 States of matter Part 2 Assistant Lecturer in Pharmaceutics Overview The Liquid State General properties Liquefaction of gases Vapor pressure of liquids Boiling point The Solid
More informationLecture Phase transformations. Fys2160,
Lecture 12 01.10.2018 Phase transformations Fys2160, 2018 1 A phase transformation Discontinuous change in the properties of substance when the environent is changed infinitesimaly. Change between phases
More informationHomework - Lecture 11.
Homework - Lecture 11. Name: Topic: Heat Capacity and Specific Heat Type: Numerical 1. Two liquids, A and B, are mixed together, and the resulting temperature is 22 C. If liquid A has mass m and was initially
More informationName Date Class STATES OF MATTER. Match the correct state of matter with each description of water by writing a letter on each line.
10 STATES OF MATTER SECTION 10.1 THE NATURE OF GASES (pages 267 272) This section describes how the kinetic theory applies to gases. It defines gas pressure and explains how temperature is related to the
More informationCHAPTER 12 GASES AND KINETIC-MOLECULAR THEORY
. Pressure CHAPER GASES AND KINEIC-MOLECULAR HEORY. Boyle s Law: he -P Relationship 3. Charles Law: he - Relationship 4. Standard &P 5. he Combined Gas Law Equation 6. Avogadro s Law and the Standard Molar
More information0.5 kpa (1000 Pa/kPa) *A. A = 70*9.81 N/500 N/m 2 = 1.37 m 2
AREN 2110 Spring 2010 Homework #2: Due Friday, Jan 29, 6 PM Solutions 1. Consider a 70-kg woman who has a total footprint area of 400 cm2. She wishes to walk on the snow, but the snow cannot withstand
More informationProblem Set #10 Assigned November 8, 2013 Due Friday, November 15, 2013 Please show all work for credit To Hand in
Problem Set #10 Assigned November 8, 2013 Due Friday, November 15, 2013 Please show all work for credit To Hand in 1. 2. 1 3. 4. The vapor pressure of an unknown solid is approximately given by ln(p/torr)
More informationFUNDAMENTALS OF THERMODYNAMICS AND HEAT TRANSFER
FUNDAMENTALS OF THERMODYNAMICS AND HEAT TRANSFER Lecture 2: Evaluating properties Pierwsza strona STATES OF THE MATTER Phase is a quantity is of matter that is homogeneous throughout in both chemical composition
More informationPure Substances Phase Change, Property Tables and Diagrams
Pure Substances Phase Change, Property Tables and Diagrams In this chapter we consider the property values and relationships of a pure substance (such as water) which can exist in three phases - solid,
More informationChapter 8 Phase Diagram, Relative Stability of Solid, Liquid, and Gas
Chapter 8 Phase Diagram, Relative Stability of Solid, Liquid, and Gas Three states of matter: solid, liquid, gas (plasma) At low T: Solid is most stable. At high T: liquid or gas is most stable. Ex: Most
More informationAP Chemistry Ch 5 Gases
AP Chemistry Ch 5 Gases Barometer - invented by Evangelista Torricelli in 1643; uses the height of a column of mercury to measure gas pressure (especially atmospheric) Manometer- a device for measuring
More informationChapter 2 Solutions. 2.1 (D) Pressure and temperature are dependent during phase change and independent when in a single phase.
Chater Solutions.1 (D) Pressure and temerature are deendent during hase change and indeendent when in a single hase.. (B) Sublimation is the direct conversion of a solid to a gas. To observe this rocess,
More informationPhysics Nov Phase Transitions
Physics 301 11-Nov-1999 15-1 Phase Transitions Phase transitions occur throughout physics. We are all familiar with melting ice and boiling water. But other kinds of phase transitions occur as well. Some
More informationCHAPTER (2) FLUID PROPERTIES SUMMARY DR. MUNZER EBAID MECH.ENG.DEPT.
CHAPTER () SUMMARY DR. MUNZER EBAID MECH.ENG.DEPT. 08/1/010 DR.MUNZER EBAID 1 System Is defined as a given quantity of matter. Extensive Property Can be identified when it is Dependent on the total mass
More informationThermal Physics. Temperature (Definition #1): a measure of the average random kinetic energy of all the particles of a system Units: o C, K
Thermal Physics Internal Energy: total potential energy and random kinetic energy of the molecules of a substance Symbol: U Units: J Internal Kinetic Energy: arises from random translational, vibrational,
More informationUnit 10: Part 1: Polarity and Intermolecular Forces
Unit 10: Part 1: Polarity and Intermolecular Forces Name: Block: Intermolecular Forces of Attraction and Phase Changes Intramolecular Bonding: attractive forces that occur between atoms WITHIN a molecule;
More informationEngineering Thermodynamics
David Ng Summer 2017 Contents 1 July 5, 2017 3 1.1 Thermodynamics................................ 3 2 July 7, 2017 3 2.1 Properties.................................... 3 3 July 10, 2017 4 3.1 Systems.....................................
More informationThermodynamics Introduction and Basic Concepts
Thermodynamics Introduction and Basic Concepts by Asst. Prof. Channarong Asavatesanupap Mechanical Engineering Department Faculty of Engineering Thammasat University 2 What is Thermodynamics? Thermodynamics
More informationChem 4501 Introduction to Thermodynamics, 3 Credits Kinetics, and Statistical Mechanics
Chem 4501 Introduction to hermodynamics, 3 Credits Kinetics, and Statistical Mechanics Module Number 2 Active Learning Answers and Optional Problems/Solutions 1. McQuarrie and Simon, 2-6. Paraphrase: How
More informationThermodynamics 1 Lecture Note 1
Thermodynamics 1 Lecture Note 1 March 02, 2015 Kwang Kim Yonsei University kbkim@yonsei.ac.kr 39 8 7 34 53 Y O N Se I 88.91 16.00 14.01 78.96 126.9 Scientific Thinking - System under investigation - Description
More informationLecture 6. NONELECTROLYTE SOLUTONS
Lecture 6. NONELECTROLYTE SOLUTONS NONELECTROLYTE SOLUTIONS SOLUTIONS single phase homogeneous mixture of two or more components NONELECTROLYTES do not contain ionic species. CONCENTRATION UNITS percent
More informationPhase Changes and Latent Heat
Review Questions Why can a person remove a piece of dry aluminum foil from a hot oven with bare fingers without getting burned, yet will be burned doing so if the foil is wet. Equal quantities of alcohol
More information