NSG 4070C APPLICATION FOR MIL-STD 461G CS 114
|
|
- Allyson Lawson
- 6 years ago
- Views:
Transcription
1 out < +0 meter ch. < +0 ch. < +0 ch. < +7 M nd NSG 0C APPLICATION FOR MIL-STD G CS Test parameter Equipment Standard: MIL-STD G CS Frequency range: to 00 M Curve to : see diagrams Modulation: pulse modulation, 0 % duty cycle erification method: Measuring deviation max. db Test method: Substitution method with db current limitation Monitoring probe: Required for limiting the induced current Signal generation: NSG 0C-0 Modulator: included in NSG 0C-0 meter: x included in NSG 0C-0 amplifier: included in NSG 0C-0 Directional coupler: included in NSG 0C-0 Current injection probe: CIP A Monitoring probe: MD 0A : x PCJ 0B Termination: x 0 Ω 0 W Attenuation: db, db, 0 db, 0 db as shown in table Device control: incl. in NSG 0 user interface Software (optional): icd.control version. or higher WARNING: The power meter inputs are very sensitive. It is the user s responsibility to ensure that the selected test levels does not damage the equipment. Any hardware/setup changes should be calculated before starting the test. Calibration set-up for monitoring probe PCJ 0B NSG 0 NSG 0C-0 meter ch. Remarks: It is recommended to connect the MD 0 remote port with the user port of NSG 0 and select the function MD 0 adaptive probe in the NSG 0 firmware (version. or higher). The monitoring probe MD 0 will be calibrated in passive and active mode automatically. MD 0A + FIX MD0
2 Test level for MIL STD G CS curve # Test level for MIL STD G CS curve # , Frequency in M , Frequency in M 8 7 Test level for MIL STD G CS curve # Test level for MIL STD G CS curve # , Frequency in M , Frequency in M 7 8 Test level for MIL STD G CS curve # , Frequency in M Use of the attenuators on the and on the power meter channel of NSG 0C-0 Test level of MIL-STD-G CS Attenuator in db on CIP A Attenuator in db on power meter of NSG 0C-0 Curve # 0 Curve # 0 Curve # 0 0 Curve # 0 Curve # dbµa ( to 0 ) dbµa (0 to M) 0 Table : Use of the attenuators
3 out < +0 out < +0 out < +0 meter ch. < +0 ch. < +0 ch. < +7 meter ch. < +0 ch. < +0 ch. < +7 meter ch. < +0 ch. < +0 ch. < +7 M M M nd nd nd Calibration set-up for curve # to curve # and 77 dbµa (for 77 dbµa in the range 0 to M) NSG 0 NSG 0C-0 Please use the attenuator with values as given in Table to allow level setting above the amplifier noise. PCJ 0B meter ch. MD 0A + FIX MD0 CIP A Attenuator as required for the test level erification set-up for curve # to curve # and 77 dbµa (for 77 dbµa in the range 0 to M) NSG 0 NSG 0C-0 Please use the same attenuators and the same cables as used for system and probe PCJ 0B meter ch. MD 0A + FIX MD0 CIP A Attenuator as use for system calibration Test set-up for curve # to curve # and 77 dbµa (for 77 dbµa in the range 0 to M) supply unit PSU 00 NSG 0 NSG 0C-0 Please use the same attenuators and the same cables as used for system and probe meter ch. Attenuator as use for system calibration MD 0A CIP A power / signal cable
4 out < +0 out < +0 out < +0 meter ch. < +0 ch. < +0 ch. < +7 meter ch. < +0 ch. < +0 ch. < +7 meter ch. < +0 ch. < +0 ch. < +7 M M M nd nd nd Calibration set-up for curve # NSG 0 NSG 0C-0 Please use a 0 db attenuator to protect power meter channel. Remove the attenuator on the BCI probe. 0 db Attenuator PCJ 0B meter ch. MD 0A + FIX MD0 CIP A erification set-up for curve # NSG 0 NSG 0C-0 PCJ 0B meter ch. MD 0A + FIX MD0 CIP A Test set-up for curve # NSG 0 NSG 0C-0 supply unit PSU 00 meter ch. MD 0A CIP A power / signal cable
5 out < +0 out < +0 meter ch. < +0 ch. < +0 ch. < +7 meter ch. < +0 ch. < +0 ch. < +7 M M nd nd Calibration set-up for 77 dbµa in the range to 0 NSG 0 NSG 0C-0 Please remove the 0 db attenuator to protect power meter and the attenuator on the. PCJ 0B meter ch. MD 0A + FIX MD0 CIP A Test set-up for for 77 dbµa in the range to 0 NSG 0 NSG 0C-0 supply unit PSU 00 meter ch. MD 0A CIP A power / signal cable AMETEK CTS Europe GmbH Landsberger Str. Berlin Germany T F info.rf.cts@ametek.com December 07 Teseq Specifications subject to change without notice. Teseq is an ISO-registered company. Its products are designed and manufactured under the strict quality and environmental requirements of the ISO 00. This document has been carefully checked. However, Teseq does not assume any liability for errors or inaccuracies. 8- E0 MIL-STD G Dec. 07
Ultra-Small Footprint N-Channel FemtoFET MOSFET Test EVM
User's Guide SLPU007 December 07 Ultra-Small Footprint N-Channel FemtoFET MOSFET Test EVM Contents Introduction... Description... Electrical Performance Specifications... 4 Schematic... 4 Test Setup....
More information(Cat. No CFM) Product Data
(Cat. No. 1771-CFM) Product Data The CFM module interfaces Allen-Bradley programmable logic controllers (PLCs ) with magnetic pickups, single-channel shaft encoders, turbine flowmeters or any source of
More informationRheolabQC. Rotational Rheometer for Quality Control. ::: Intelligence in Rheometry
RheolabQC Rotational Rheometer for Quality Control ::: Intelligence in Rheometry RheolabQC The Powerful QC Instrument Viscosity measurement and rheological checks for quality control are made routine and
More informationPhysical Structure of Matter Hall effect in p-germanium with Cobra3. Solid-state Physics, Plasma Physics.
Physical Structure of Matter Solid-state Physics, Plasma Physics Hall effect in p-germanium with Cobra3 What you can learn about Semiconductor Band theory Forbidden zone Intrinsic conductivity Extrinsic
More informationCaution! Pay close attention to the special operation and safety instructions in the manual of the ultrasonic echoscope.
Ultrasonic B-Scan TEAS Related topics Sound velocity, reflection coefficient, ultrasonic echography, A-scan, B-scan, grey-scale dis-play, resolution, zone of focus, and image artefacts. Principle The fundamental
More informationIon-Chamber Survey Meter OD-02
Ion-Chamber Survey Meter OD-02 Dose and dose rate meter for measuring the ambient dose equivalent H*(10) and dose rate equivalent dh*(10)/dt as well as the directional dose equivalent H (0,07) and dose
More informationAN2970 Application note
Application note Principles of capacitive touch and proximity sensing technology The objective of this document is to present the principles of capacitive sensing and charge transfer used in STMicroelectronics
More informationISOCON-6. 24V AC or DC POWERED ISOLATING SIGNAL CONVERTER
ISOCON-6 24V AC or DC POWERED ISOLATING SIGNAL CONVERTER Whilst every effort has been taken to ensure the accuracy of this document, we accept no responsibility for damage, injury, loss or expense resulting
More informationThis chip is used for: power modules. Applications: drives G. Mechanical Parameters Raster size x 13.63
SIGC186T170R3 IGBT3 Power Chip Features: 1700V Trench & Field Stop technology low turn-off losses short tail current positive temperature coefficient easy paralleling This chip is used for: power modules
More informationShear waves in solid-state materials
Shear waves in solid-state materials TEAS Related topics Ultrasonic transmission measurement, propagation of ultrasound waves, ultrasound wave modes, shear waves, longitudinal and transverse waves, modulus
More informationPower Resistor for Mounting onto a Heatsink Thick Film Technology
Power Resistor for Mounting onto a Heatsink FEATURES 1 % tolerance available High power rating = 200 W Wide ohmic value range = 0.046 Ωto 1 MΩ Non inductive Easy mounting Low thermal radiation of the case
More informationTPM(A) Quick Startup Guide SIEMENS SINAMICS S120
Quick Startup Guide TPM(A) 00 110 SIEMENS SINAMICS S120 Version : 1.2 Date : 1 th December 200 File : 091_D012_0.doc Doc.No. : 091-D012-0 Technical changes reserved! Table of Contents TABLE OF CONTENTS...
More informationElectrical safety testing Checklist
ety al Check testing Check - Checklist EN) ctrical Electrical safety testing Checklist SOP - Electrical Check Copyright 2013 Eppendorf AG. All rights reserved, including graphics and images. No part of
More informationPower Resistors for Mounting Onto a Heatsink Thick Film Technology
Power Resistors for Mounting Onto a Heatsink Thick Film Technology DESIGN SUPPORT TOOLS click logo to get started FEATURES 1% tolerance available High power rating = 200 W Wide ohmic value range = 0.046
More information473-SHX Dew Point Mirror
Humidity and Temperature Reference Hygrometer For Temperature up to 125 C Precise and stable chilled mirror dew point mirror technology High temperature optical components High temperature sample fan Cable
More informationCHV Series Vector Control Inverter Options. Operating Instructions for Tension Control Card
CHV Series Vector Control Inverter Options Operating Instructions for Control Card 1. Model and Specifications 1.1 Model The model of tension card is CHV00ZL. CHV series inverter can conduct constant
More informationThis chip is used for: power modules. Applications: drives G. Mechanical Parameters Raster size 9.47 x 12.08
IGBT3 Power Chip Features: 1700V Trench + Field stop technology low switching losses and saturation losses soft turn off positive temperature coefficient easy paralleling This chip is used for: power modules
More informationPTC04-DB-HALL02. Daughter Board for Melexis PTC devices. Features and Benefits. Applications. Ordering Information. Accessories. 1. Functional Diagram
PTC0-DB-HALL0 Features and Benefits PTC0 interface board for testing devices: 0 0 0 Applications Experimental tool for Lab and Prototyping Production Equipment for Serial Programming Ordering Information
More informationPHOENIX CONTACT - 04/2016. Features
Signal conditioner Data sheet 100238_de_06 1 Description PHOENIX CONTACT - 04/2016 Features The MCR-C-UI-UI(-450)-DCI(-NC) 3-way isolation amplifier is used to electrically isolate and convert analog signals.
More informationSoftware BioScout-Calibrator June 2013
SARAD GmbH BioScout -Calibrator 1 Manual Software BioScout-Calibrator June 2013 SARAD GmbH Tel.: ++49 (0)351 / 6580712 Wiesbadener Straße 10 FAX: ++49 (0)351 / 6580718 D-01159 Dresden email: support@sarad.de
More informationSemi-automatic titrators PH-Burette. A great ph-meter with integrated burette. Incredible price! Infinite possibilities
Semi-automatic titrators PH-Burette. A great ph-meter with integrated burette. Incredible price! Infinite possibilities instruments 5 YEARS G U A R A N T E E Quality at a reasonable price The optimum combination
More informationCapaciTorr HV 200 HIGHLIGHTS
CapaciTorr HV 200 General Features High pumping speed for all active gases High sorption capacity and increased lifetime Costant pumping speed in HV, UHV and XHV Reversible pumping of hydrogen and its
More informationPascal ET is an handheld multifunction calibrator for the measurement and simulation of the following parameters: - pressure
DATASHEET Pascal ET Pascal ET is an handheld multifunction calibrator for the measurement and simulation of the following parameters: - pressure - electrical signals (ma, mv, V, ) - temperature (TC and
More informationHOW ADVANCED PYROMETERS INCREASE THERMAL PROCESS REPEATABILITY AND PRODUCT QUALITY
HOW ADVANCED PYROMETERS INCREASE THERMAL PROCESS REPEATABILITY AND PRODUCT QUALITY Accurate temperature measurement is key for controlling the stability and repeatability of many temperature-critical processes.
More informationSI Surging Ideas TVS Diode Application Note PROTECTION PRODUCTS. Layout Guidelines for adding ESD Protection in HDMI Receiver Applications
Layout Guidelines for adding ESD Protection in HDMI Receiver Applications The High Definition Multimedia Interface (HDMI) video signals are transmitted on very high speed differential pairs. These lines
More information30 W Power Resistor Thick Film Technology
30 W Power Resistor Thick Film Technology LTO series are the extension of RTO types. We used the direct ceramic mounting design (no metal tab) of our RCH power resistors applied to semiconductor packages.
More informationMAC Aura XB Acoustic Test Report
MAC Aura XB Acoustic Test Report 2017. Information subject to change without notice. HARMAN Professional and all affiliated companies disclaim liability for any injury, damage, direct or indirect loss,
More informationKeysight Technologies Measurement Uncertainty of VNA Based TDR/TDT Measurement. Application Note
Keysight Technologies Measurement Uncertainty of VNA Based TDR/TDT Measurement Application Note Table of Contents Introduction... 3 S-parameter measurement uncertainty of VNA... 4 Simplification of systematic
More informationLow-Voltage Single SPDT Analog Switch
Low-Voltage Single SPDT Analog Switch DG22 DESCRIPTION The DG22 is a single-pole/double-throw monolithic CMOS analog switch designed for high performance switching of analog signals. Combining low power,
More informationAcceleration/Velocity/Displacement VIBRATION METER
Acceleration/Velocity/Displacement VIBRATION METER Model : VB-8220 Your purchase of this VIBRATION METER marks a step forward for you into the field of precision measurement. Although this METER is a complex
More informationVNA Tools II S-parameter uncertainty calculation
VA Tools II S-parameter uncertainty calculation Michael Wollensack METAS 5. May 0 Michael Wollensack METAS Outline Introduction VA Measurement Model Database Uncertainty Visualization Results Michael Wollensack
More informationDrive electronics pq12
Drive electronics pq12 Amplifier module with constant current controller for proportional valves Control of one solenoid Easy mounting directly on bearing rails acc. to EN 50022 Standard voltage and current
More informationAcceleration, Velocity, Separate probe VIBRATION METER Model : VB-8202
Acceleration, Velocity, Separate probe VIBRATION METER Model : VB-8202 Your purchase of this VIBRATION METER marks a step forward for you into the field of precision measurement. Although this METER is
More informationE2T0 DVP
29-5-26 5116868-E2T DVP-11363-1 ENGLISH Thank you for choosing Delta s DVP series PLC. DVP4TC-E2 temperature measurement module receives 4 points of external thermocouple temperature sensors (J-type, K-type,
More informationPRODUCT SPECIFICATIONS
FEATURES AND BENEFITS* Up to 1,000,000 duty cycles or 10 year DC life 48V DC working voltage Active cell balancing Temperature output Overvoltage outputs available High power density TYPICAL APPLICATIONS
More informationINFORMATION TECHNOLOGY SYSTEMS SPDs FOR 19 TECHNOLOGY. NET Protector Surge Arrester. Protects switches, HUBs and telecommunication
Surge Arrester Protects switches, HUBs and telecommunication systems Class D according to EN 0 possible (Gigabit Ethernet) Variably equippable patch panels Units available with plug-in inputs and outputs
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 21501-2 First edition 2007-05-15 Determination of particle size distribution Single particle light interaction methods Part 2: Light scattering liquid-borne particle counter
More informationK D A A M P L I F I E R S F I R M W A R E U S E R G U I D E
K D A A M P L I F I E R S F I R M W A R E U S E R G U I D E T A B L E O F C O N T E N T S S E C T I O N 1 : P R E PA R I N G Y O U R F I L E S Via Network Router 3 S E C T I O N 2 : A C C E S S I N G T
More informationDewpoint Meter Data Sheet / Instructions
Paint Test Equipment Dewpoint Meter Data Sheet / Instructions Dewpoint Meter Information ISO 8502-4: Preparation of steel substrates before application of paints and related products. Tests for the assessment
More informationEppendorf BioSpectrometer 6135/6136/6137
nal Spectrometer Qualification 6135/6136/6137 - English N) rational Qualification - English Register your instrument! www.eppendorf.com/myeppendorf Eppendorf BioSpectrometer 6135/6136/6137 SOP - Operational
More information74VHCT138ATTR 3 TO 8 LINE DECODER (INVERTING)
3 TO 8 LINE DECODER (INVERTING) HIGH SPEED: t PD = 7.6 ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 4 µa (MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS: V IH = 2V (MIN.), V IL = 0.8V (MAX) POWER
More informationProduct data sheet Palas U-SMPS 1050 / 1100 / 1200
Product data sheet Palas U-SMPS 1050 / 1100 / 1200 Applications Filter test Aerosol research Environmental and climatic studies Inhalation experiments Interior and workplace measurements Benefits Particle
More informationThree Axis Magnetic Field Transducer x-h3x-xx_e3d-2.5khz-1-0.2t
DESCRIPTION: TYPICAL APPLICATIONS: The is a high accuracy magnetic flux density-toanalogue-voltage transducer with a highlevel and temperature compensated output signal for each of the three components
More informationCNY17F-4. Pb Pb-free. Optocoupler, Phototransistor Output, No Base Connection. Vishay Semiconductors
Optocoupler, Phototransistor Output, No Base Connection Features Breakdown Voltage, 500 V RMS No Base Terminal Connection for Improved Common Mode Interface Immunity Long Term Stability Industry Standard
More informationPower Resistor for Mounting onto a Heatsink Thick Film Technology
DIMENSIONS in millimeters Power Resistor for Mounting onto a Heatsink Thick Film Technology FEATURES 300 W at 85 C bottom case temperature Wide resistance range: 0.3 Ω to 900 kω E24 series Non inductive
More informationData Sheet / Instructions. Dewpoint MeterO
Data Sheet / Instructions Dewpoint MeterO Dewpoint Meter ISO 8502-4: Preparation of steel substrates before application of paints and related products. Tests for the assessment of surface cleanliness.
More informationLEP Hall effect in p-germanium with Cobra3
Hall effect in p-germanium with Cobra3 LEP 5.3.01-11 Related topics Semiconductor, band theory, forbidden zone, intrinsic conductivity, extrinsic conductivity, valence band, conduction band, Lorentz force,
More informationCapacitor in the AC circuit with Cobra3
Capacitor in the AC circuit with Cobra3 LEP Related Topics Capacitance, Kirchhoff s laws, Maxwell s equations, AC impedance, Phase displacement Principle A capacitor is connected in a circuit with a variable-frequency
More information- compressed air plants (refrigerating/adsorption dryers) - granulate dryers - medical gases - non-corrosive gases, e. g. nitrogen
INSTRUCTION MANUAL FA 510 The CS dew point sensor FA 510 with 3-wire technology 4 20 ma and RS 485 output enables a reliable and long-term stable monitoring of the dew point in industrial applications
More informationEvaluation Board for 8-/10-/12-Bit, Parallel Input, Dual-Channel, Current Output DAC EVAL-AD5428/AD5440/AD5447EB
Evaluation Board for 8-/0-/-Bit, Parallel Input, Dual-Channel, Current Output DAC EVAL-AD58/AD50/AD5EB FEATURES Operates from dual ± V and 5 V supplies On-board reference and output amplifiers Direct hookup
More informationPRODUCT SPECIFICATIONS
FEATURES AND BENEFITS* Up to 14 year DC life 56V DC working voltage Resistive cell balancing Overvoltage outputs High power density 4U, half-rack package UL registered TYPICAL APPLICATIONS UPS systems
More informationLIBSlab ANALYZERS ANALYZERS
ANALYZERS ANALYZERS Chemical multi-elemental analysis with LIBS in modular benchtop design LIBSlab LIBSpector compact sample chamber for the LIBS analysis of solid, liquid and gaseous samples. Sample chamber
More information566/568. Infrared Thermometers. Getting Started
566/568 Infrared Thermometers Getting Started PN 2812159 August 2007 Rev. 2, 4/08 2007-2008 Fluke Corporation. All rights reserved. Printed in China. Product specifications are subject to change without
More informationSubminiature Transmissive Optical Sensor with Phototransistor Output, RoHS Compliant, Released for Lead (Pb)-free Solder Process
TCPT12 Subminiature Transmissive Optical Sensor with Phototransistor Output, RoHS Compliant, Released for Lead (Pb)-free Solder Process Description The TCPT12 is a compact transmissive sensor that includes
More informationUltrasonic Gas Flow Meter
P r o d u c t i n f o r m at i o n FLOWSIC600 Ultrasonic Gas Flow Meter For custody transfer and process applications Analyzers and Process Instrumentation FLOWSIC600 For Custody Transfer and Process Applications
More informationCapaciTorr HV Pumps. making innovation happen,together
CapaciTorr HV Pumps making innovation happen,together CapaciTorr HV HIGHLIGHTS General Features High pumping speed for all active gases High sorption capacity and increased lifetime Constant pumping speed
More information2Ω, Quad, SPST, CMOS Analog Switches
9-73; Rev ; 4/ 2Ω, Quad, SPST, CMOS Analog Switches General Description The // quad analog switches feature.6ω max on-resistance (R ) when operating from a dual ±5V supply. R is matched between channels
More informationMultichannel Brake Infrared Temperature Sensor - Datasheet
The Izze-Racing Multichannel Brake Infrared Temperature Sensor is specifically designed to measure the highly transient surface temperature of a brake rotor at multiple points, making it possible to acquire
More informationSOT-363 Q 1 Q 2 TOP VIEW. Characteristic Symbol Value Unit I D. Characteristic Symbol Value Unit Drain Source Voltage V DSS -20 V
COMPLEMENTARY PAIR ENHANCEMENT MODE FIELD EFFECT TRANSISTOR Features Low On-Resistance Low Gate Threshold Voltage V GS(th) < 1V Low Input Capacitance Fast Switching Speed Low Input/Output Leakage Complementary
More informationHI-POWER / LED MICRO-08
HI-POWER / LED MICRO-08 FEATURES + Smallest form factor with up to 1.5W (500mA) output power + Ultra wide illumination field angle (FWHM 155 degree) + Low thermal resistance:
More informationSFH615A/SFH6156. Optocoupler, Phototransistor Output, High Reliability, 5300 V RMS. Vishay Semiconductors
Optocoupler, Phototransistor Output, High Reliability, 300 V RMS Features Excellent CTR Linearity Depending on Forward Current Isolation Test Voltage, 300 V RMS e3 Fast Switching Times Low CTR Degradation
More informationSOT-563 Q 1 Q 2 BOTTOM VIEW. Characteristic Symbol Value Unit Drain Source Voltage V DSS 20 V Gate-Source Voltage V GSS ±8 V T A = 25 C T A = 85 C
COMPLEMENTARY PAIR ENHANCEMENT MODE FIELD EFFECT TRANSISTOR Features Mechanical Data Low On-Resistance Low Gate Threshold Voltage V GS(th)
More informationAN3002 Thermocouple measurement
AN3002 Thermocouple measurement This application note illustrates the correct measurement of thermocouple sensors. Contents 1 Introduction......................................... 3 2 Test configuration....................................
More informationDG211. Features. SPST 4-Channel Analog Switch. Part Number Information. Functional Block Diagrams. Pinout. Data Sheet December 21, 2005 FN3118.
Data Sheet FN3118.4 SPST 4-Channel Analog Switch The is a low cost, CMOS monolithic, Quad SPST analog switch. It can be used in general purpose switching applications for communications, instrumentation,
More informationPower Resistor for Mounting onto a Heatsink Thick Film Technology
DIMENSIONS in millimeters Power Resistor for Mounting onto a Heatsink Thick Film Technology FEATURES 800 W at 85 C bottom case temperature Wide resistance range: 0.3 Ω to 900 kω E24 series Non inductive
More informationLOW HIGH OFF ON. Maxim Integrated Products 1
9-79; Rev ; /07 Low-Voltage, Quad, SPST General Description The MAX0/MAX/MAX are quad, low-voltage, single-pole/single-throw (SPST) analog switches. On-resistance (00Ω, max) is matched between switches
More informationMP112D GHz GaAs MMIC Attenuator. Datasheet
MP112D 0.1-15 GHz GaAs MMIC Attenuator Datasheet MP112D 0.1-15 GHz GaAs MMIC Attenuator MAIN FEATURES Operating range 0.1 to 15 GHz Insertion loss 4.5 db at 10 GHz Attenuation range 31.5 db (6 bit, 64
More informationApplication Note. Electrical. Optical
Application Note Electrical Vector Network Analyzer Port 1 Port 2 Electrical Electrical MX40G E-O Converter Optical O-E Device Under Test Using the MX40G: De Embedding Procedures One of the primary applications
More informationSurvey Meter OD-01 Address: Phone: Fax: URL:
Survey Meter OD-01 Dose meter and dose rate meter for the measurement of the ambient dose and dose rate equivalent H*(10), dh*(10)/dt and the directional dose and dose rate equivalent H'(0.07), dh'(0.07)/dt
More informationPowered-off Protection, 1, 1.8 V to 5.5 V, SPDT Analog Switch (2:1 Multiplexer)
DGE Powered-off Protection,,.8 V to 5.5 V, SPDT Analog Switch (: Multiplexer) DESCRIPTION The DGE is a high performance single-pole, double-throw (SPDT) analog switch designed for.8 V to 5.5 V operation
More informationLow Drop Voltage Regulator TLE
Low Drop Voltage Regulator TLE 4296-2 Features Two versions: 3.3 V, 5.0 V Output voltage tolerance ±4% Very low drop voltage Output current: 30 ma Inhibit input Low quiescent current consumption Wide operation
More informationACCEPTANCE PROCEDURE FOR ROMET ROTARY METER BODIES AND/OR MECHANICAL NON-CONVERTING AND CONVERTING MODULES
ACCEPTANCE PROCEDURE FOR ROMET ROTARY METER BODIES AND/OR MECHANICAL NON-CONVERTING AND CONVERTING MODULES (RPB-01) Approved by: Date: SECTION PAGE # 1.0 Scope 2.0 Definitions 3.0 References 4.0 Inspection
More informationVK2 volume flow controller Overview
New option with sound attenuator Maintenance-free VK2 volume flow controller that operates without an auxiliary power supply, for ventilation and air conditioning systems. Adjustable on site. Outstanding
More informationPowered-off Protection, 6, 1.8 V to 5.5 V, SPDT Analog Switch (2:1 Multiplexer)
Powered-off Protection,, 1. V to 5.5 V, SPDT Analog Switch (:1 Multiplexer) DESCRIPTION The is a high performance single-pole, double-throw (SPDT) analog switch designed for 1. V to 5.5 V operation with
More informationThis chip is used for: power module BSM 75GD120DN2. Emitter pad size 8 x ( 2.99 x 1.97 ) Thickness 200 µm. Wafer size 150 mm
IGBT Chip in NPT-technology Features: 1200V NPT technology low turn-off losses short tail current positive temperature coefficient easy paralleling integrated gate resistor This chip is used for: power
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 14850-1 First edition 2004-05-15 Nuclear energy Waste-packages activity measurement Part 1: High-resolution gamma spectrometry in integral mode with open geometry Énergie nucléaire
More informationLow-Voltage Single SPDT Analog Switch
Low-Voltage Single SPDT Analog Switch DG22 DESCRIPTION The DG22 is a single-pole/double-throw monolithic CMOS analog switch designed for high performance switching of analog signals. Combining low power,
More informationFATEK. FBs-1HLC. Precision Load Cell Module. Operation manual V1.1 06/07/2017 FATEK AUTOMATION CORP.
FATEK FBs-1HLC Precision Load Cell Module Operation manual V1.1 06/07/2017 FATEK AUTOMATION CORP. 1 Contents Chapter 1 1HLC module introduction... 3 1.1 Module specification... 3 1.2 Module appearance
More informationVMS-GeoMil. Background
Background When using a drilling rig for cone penetration testing, a mechanical clamp can be mounted to the drilling head (by means of a special transition piece). The depth than can be achieved depends
More informationSHENZHEN MORLAB COMMUNICATIONS TECHNOLOGY CO., LTD
SAR Reference Dipole Calibration Report Ref : ACR.189.7.16.SATU.A SHENZHEN MORLAB COMMUNICATIONS TECHNOLOGY CO., LTD FL3, BUILDING A, FEIYANG SCIENCE PARK, NO.8 LONGCHANG ROAD, BLOCK 67, BAOAN DISTRICT,
More informationWhite Paper. Perform Conductivity Measurements In Compliance with USP <645>
Perform Conductivity Measurements In Compliance with USP Water is the most widely used substance, raw material, or ingredient in the production, processing and formulation of compendial articles.
More information-202mA. Pin 1 D1. Diode. Part Number Case Packaging DMC21D1UDA-7B X2-DFN ,000/Tape & Reel
DMCDUDA COMPLEMENTARY PAIR ENHANCEMENT MODE MOSFET Product Summary Device BV DSS R DS(ON) max I D max T A = + C.99Ω @ V GS =.V ma Q V.Ω @ V GS =.V ma.8ω @ V GS =.8V 8mA.Ω @ V GS =.V 9mA Features and Benefits
More informationNEW! PCR next to me. Eppendorf Mastercycler nexus: combine, connect, control
NEW! PCR next to me Eppendorf Mastercycler nexus: combine, connect, control PCR next to me Eppendorf Mastercycler nexus family In the age of networking, the new Mastercycler nexus is your reliable companion
More informationODEON APPLICATION NOTE Calibration of Impulse Response Measurements
ODEON APPLICATION NOTE Calibration of Impulse Response Measurements Part 2 Free Field Method GK, CLC - May 2015 Scope In this application note we explain how to use the Free-field calibration tool in ODEON
More informationLecture 17 Date:
Lecture 17 Date: 09.03.017 The Quadrature Hybrid We began our discussion of dividers and couplers by considering important general properties of three- and four-port networks. This was followed by an analysis
More informationThe Fundamentals of Moisture Calibration
The Fundamentals of Moisture The following guide will provide you with a basic knowledge of humidity calibration, help you to understand your requirements and select an appropriate solution. 1 Why Humidity
More informationPower Resistor for Mounting onto a Heatsink Thick Film Technology
DIMENSIONS in millimeters Power Resistor for Mounting onto a Heatsink Thick Film Technology FEATURES LPS high power: 1 W Wide resistance range: 1 Ω to 1.3 kω E24 series Non inductive Easy mounting Low
More informationv = m / s Thermal Flow Sensors TA with thin-film sensor element Probes Probe Guides Measuring Tubes
Thermal Flow Sensors TA with thin-film sensor element Probes Probe Guides Measuring Tubes Examples of Application Flow measurements also in hazardous locations X zone 0 or zone 1 in clean rooms in air
More informationOperating Instructions for Digital Manometer. Model: MAN-SD
Operating Instructions for Digital Manometer Model: MAN-SD 1. Contents 1. Contents...2 2. Note...3 3. Instrument Inspection...3 4. Regulation Use...4 5. Operating Principle...4 6. Mechanical Connection...5
More informationO P E R A T I N G M A N U A L
OPERATING MANUAL WeatherJack OPERATING MANUAL 1-800-645-1061 The baud rate is 2400 ( 8 bits, 1 stop bit, no parity. Flow control = none) To make sure the unit is on line, send an X. the machine will respond
More informationPower Resistor for Mounting onto a Heatsink Thick Film Technology
Power Resistor for Mounting onto a Heatsink Thick Film Technology DESIGN SUPPORT TOOLS click logo to get started FEATURES 300 W at 85 C bottom case temperature Wide resistance range: 0.3 to 900 k E24 series
More informationFundamentals of Particle Counting
Fundamentals of Particle Counting 1 Particle Counting: Remains the most significant technique for determining the cleanliness level of a fluid Useful as a tool for qualification and monitoring cleanroom
More informationElectric amplifiers. RE 30044/02.12 Replaces: Type VT-VRPA X/V0/RTS-2STV. Component series 2X 1/8
Electric amplifiers RE 30044/02.12 Replaces: 11.02 1/8 Type VT-VRPA1-527-2X/V0/RTS-2STV Component series 2X Table of contents Contents Page Features 1 Ordering code, accessories 2 Front plate 2 Block diagram
More informationPower Resistors, for Mounting onto a Heatsink Thick Film Technology
RCH Manufactured in cermet thick fi lm technology, these power resistors exhibit remarkable characteristics and the series includes 4 types ranging from 5 W to 50 W Designed to be mounted onto a heatsink,
More informationSHENZHEN SEM.TEST TECHNOLOGY CO., LTD. 1/F, BUILDING A, HONGWEI INDUSTRIAL PARK, LIUXIAN 2ND ROAD BAO'AN DISTRICT SHENZHEN (518101), CHINA
COMOSAR E-Field Probe Calibration Report Ref : ACR.154.4.15.SATU.A SHENZHEN SEM.TEST TECHNOLOGY CO., LTD. 1/F, BUILDING A, HONGWEI INDUSTRIAL PARK, LIUXIAN 2ND ROAD BAO'AN DISTRICT SHENZHEN (518101), CHINA
More informationAccuracy Estimations of S-Parameter Measurements at the Wafer-Level
WORKSHOP WSF13 (EuMC/EuMIC) Determining Accuracy of Measurements at High Frequencies from Error to Uncertainty Accuracy Estimations of S-Parameter Measurements at the Wafer-Level H. Heuermann*, A. Rumiantsev**
More informationPower Resistor for Mounting onto a Heatsink Thick Film Technology
DIMENSIONS in millimeters Power Resistor for Mounting onto a Heatsink Thick Film Technology FEATURES LPS high power: 1 W Wide resistance range: 1 Ω to 1.3 kω E24 series Non inductive Easy mounting Low
More informationAnalyst Software. Automatic Optimization Tutorial
This document is provided to customers who have purchased AB Sciex equipment to use in the operation of such AB Sciex equipment. This document is copyright protected and any reproduction of this document
More informationPart Type differentiation Package 1N5550 V RRM = 200 V G-4 1N5551 V RRM = 400 V G-4 1N5552 V RRM = 600 V G-4
VISHAY 1N5550 to 1N5552 Standard Sinterglass Diode Features Cavity-free glass passivated junction High temperature metallurgically bonded construction Hermetically sealed package Medium switching for improved
More informationOptocoupler, Phototransistor Output, with Base Connection
Vishay Semiconductors Optocoupler, Phototransistor Output, FEATURES A 6 B Isolation test voltage 5300 V RMS Interfaces with common logic families C NC 2 3 V D E 5 4 C E Input-output coupling capacitance
More information