Solutions to Problems in Chapter 5
|
|
- Joella Morrison
- 5 years ago
- Views:
Transcription
1 Appendix E Solutions to Problems in Chapter 5 E. Problem 5. Properties of the two-port network The network is mismatched at both ports (s 0 and s 0). The network is reciprocal (s s ). The network is symmetrical (s s and s s ) The network is lossless, since its matrix is a unitary matrix. (S T S I). The unitary matrix condition yields S T S ( 5 j j (( 5 Reflection loss and insertion loss 5 ) + ( 0 ) ( 5 j j 5 ) 0 ( 5 ) ) + ( ) ) (E.) ( ) 0 I (E.) 0 The reflection losses at port and port are RL 0 lg 8.3 db and RL 0 lg 8.3 db (E.3) s s The insertion loss is given by IL 0 lg db and IL 0 lg db (E.4) s s Renormalization of scattering matrix from 50 Ω to 00 Ω The set of equations required for the renormalization is given in Section (S S 50 Ω and S new S 00 Ω ).
2 APPENDIX E. SOLUTIONS TO PROBLEMS IN CHAPTER 5 S new ( ( (s r) ( rs ) + rs s s r ) ) ( det S s r ) (s r) ( rs ) + rs s (E.5) where det S ( rs ) ( rs ) r s s (E.6) and r,new,new + (E.7) Using the given values we get r 3 Hence, the renormalized matrix is S new ( ) 7 j4 5 j4 7 and det S 00 7 ( 0.8 ) j0.96 j (E.8) (E.9) Validation by circuit simulation (ADS) We will validate our result by using a circuit simulator (ADS from Agilent, Inc.). First, we write our initial scattering parameter in a snp-file (see Section 5.7). snp-files (n number of ports) contain frequency dependent scattering parameters from simulation or measurement in ASCII format. Here, we use the file to define scattering parameters. Figure E.: sp-file for s-parameter definition Figure E. shows the sp-file. Lines with an exclamation mark (!) are comment line. The line with the sharp symbol (#) defines the format of the subsequent data lines: frequency in GHz (GHz), s-parameters (S) are given with magnitude and phase (MA). The port reference impedance (R) is 50 Ω (50). In our problem the s-parameters do not vary with frequency. In order to calculate and plot the parameters with ADS an arbitrary frequency range from GHz to GHz is chosen. The s-parameter data is give in decimal nomination. We use the previously defined sp-file in a circuit simulation. Figure E. shows the schematic. The two-port network is connected to 50 Ω as well as 00 Ω terminals. Figure E.3 shows the simulation results. The upper two plots show the s-parameters normalized to 50 Ω. The absolute values (magnitude) correspond to the given values of 5/ 0.385
3 APPENDIX E. SOLUTIONS TO PROBLEMS IN CHAPTER 5 3 Figure E.: Schematic for renormalization of scattering parameters and / The phases are zero degree (positive real value) for the reflection coefficients and 90 degree (positive imaginary value) for the transmission coefficients. The lower two plots show the s-parameters for a reference value of 00 Ω. The absolute values are 0.8 and The faces are 80 degree (negative real values) for the reflection coefficients and 90 degree (positive imaginary values) for the transmission coefficients. The results agree with our calculated values in Equation E.9.
4 APPENDIX E. SOLUTIONS TO PROBLEMS IN CHAPTER 5 4 Figure E.3: Simulation results: s-parameters for 50 Ω (upper plots) and s-parameters for,new 00 Ω (lower plots)
5 APPENDIX E. SOLUTIONS TO PROBLEMS IN CHAPTER 5 5 E. Problem 5. Antenna input impedance The reflection coefficient r A of an antenna is determined by its input impedance Z A and the port reference impedance. Solving Equation E.0 for Z A yields r A Z A Z A + (E.0) We rewrite the given reflection coefficient r A Z A + r A r A (E.) r A 0.4e j0 0.4 (cos(0 ) j sin(0 )) Re {r A } + j Im {r A } j0.7 Substituting our result in Equation E. yields + r A + Re {r A } + j Im {r A } Z A r A Re {r A } j Im {r A } (E.) (E.) ( + Re {r A } + j Im {r A }) ( Re {r A } + j Im {r A }) ( Re {r A }) + (Im {r A }) (E.4) (Re {r A }) (Im {r A }) + j Im {r A } ( Re {r A }) + (Im {r A }) (0.9 j33.5) Ω (E.5) Reflection coefficient for port reference impedance of,new 75 Ω The reflection coefficient with respect to a port reference impedance of,new 75 Ω is r A,new Z A,new Z A +,new Re {Z A} + j Im {Z A },new Re {Z A } + j Im {Z A } +,new (Re {Z A},new + j Im {Z A }) (Re {Z A } +,new j Im {Z A }) (Re {Z A } +,new ) + (Im {Z A }) (E.6) (E.7) j0.534 (E.8) Hence, magnitude and phase of the reflection coefficient are r A,new (Re {r A,new }) + (Im {r A,new }) 0.4 (E.9) ( ) Im {ra,new } r A,new arctan (E.0) Re {r A,new } Reflected and accepted power The reflected power is The accepted power is P acc P b s P a W (E.) ( s ) P a W (E.)
6 APPENDIX E. SOLUTIONS TO PROBLEMS IN CHAPTER 5 6 Validation by circuit simulation We apply a circuit simulator (ADS from Agilent, Inc.) in order to validate our results. First, we define a sp-file for the reflection coefficient with a reference impedance of 50 Ω (see Figure E.4). Once again, we chose an arbitrary frequency range from to GHz for the s- parameter representation. Figure E.4: sp-file with reflection coefficient (port reference impedance 50 Ω) Figure E.5: ADS schematic The schematic of the circuit is shown in Figure E.5. The s-parameter and impedance results are displayed in Figure E.6. There is good agreement between circuit simulation and calculation.
7 APPENDIX E. SOLUTIONS TO PROBLEMS IN CHAPTER 5 7 Figure E.6: (a) Magnitude and (b) phase of reflection coefficients for port reference impedances of 50 Ω (red) and 75 Ω (blue). (c) Real and imaginary part of reflection coefficients. (d) Real and imaginary part of input impedance.
8 APPENDIX E. SOLUTIONS TO PROBLEMS IN CHAPTER 5 8 E.3 Problem 5.3 Scattering matrix of a two port network with series impedance Figure E.7 shows a circuit with a two-port network consisting of a series impedance Z. Example 5.3 (see book page 7) gives us the procedure to calculate the scattering matrix. First, we need the input impedance. Z in Z + (E.3) The reflection coefficient then becomes s Z in Z in + + Z s (E.4) Since the network is symmetrical we get s s. Z in Two-port network U0 U Z0 Z Figure E.7: Two-port network with a series impedance Z The transmission coefficient s is given as s U U 0 Z0 + Z + + Z s (E.5) The voltage ratio U /U 0 is determined by the voltage divider rule. Due to reciprocity we get s s. Hence, the scattering matrix S is ( ) Z Z0 S (E.6) + Z Z Special cases We evaluate our result by looking at two special cases. First, we consider a short circuit (Z 0), i.e. the two-port network becomes a direct through-connection. The scattering matrix then is ( ) 0 S (E.7) 0
9 APPENDIX E. SOLUTIONS TO PROBLEMS IN CHAPTER 5 9 As expected there is no reflection (s ii 0) and full transmission ( s ij ). Next, we consider an open connection (Z ). The scattering matrix now reads ( ) 0 S (E.8) 0 As expected there is full reflection ( s ii ) and no transmission (s ij 0). Scattering matrix of T-network Z in T-network Z U Z 0 U U 0 x Z 3 Z Figure E.8: Two-port circuit with a T-network Figure E.8 shows the circuit. First, we need the input impedance. Z in Z + Z 3 (Z + ) Z + Z 3 (Z + ) Z 3 + Z + After a short calculation the input reflection coefficient is s Z in Z in + Z Z + Z Z 3 + Z Z 3 + Z Z Z0 Z Z + Z Z 3 + Z Z 3 + Z + Z + Z 3 + Z0 By swapping the indices and we get the output reflection coefficient. (E.9) (E.30) (E.3) s Z Z + Z Z 3 + Z Z 3 Z + Z Z 0 Z Z + Z Z 3 + Z Z 3 + Z + Z + Z 3 + Z 0 (E.3) The calculation of the transmission factors involves the voltage ratio U /U 0. With an auxiliary quantity U x we first determine the following voltage ratios. Finally, we get U U x s U U 0 Z + and Z0 U U x Ux U x U 0 Z 3 (Z + ) + Z + Z 3 (Z + ) Z 3 (Z + ) + Z + Z 3 (Z + ) (E.33) U 0 Z + (E.34) Z 3 Z Z + Z Z 3 + Z Z 3 + Z + Z + Z 3 + Z0 s (E.35) Due to reciprocity we find s s.
10 APPENDIX E. SOLUTIONS TO PROBLEMS IN CHAPTER 5 0 Special case Z 3 0 In order to validate our formula we consider the case Z 3 0. In this case we expect zero transmission s ij 0 and indeed Equation E.35 is zero. Equation E.3 becomes s Z in Z Z + Z Z Z0 Z in + Z Z + Z + Z + Z0 Z (Z ) + (Z ) Z (Z + ) + (Z + ) (Z + ) (Z ) (Z + ) (Z + ) Z Z + (E.36) (E.37) Since the input impedance is Z in Z our result is correct. Scattering matrix of a π-network Z in -network Z 3 U Z 0 Z U Z U 0 x Figure E.9: Two-port circuit with a π-network Figure E.9 shows the π-network. First, we calculate the input impedance. Z in Z (Z 3 + Z ) (E.38) The input reflection coefficient becomes s Z in Z in + Z Z Z 3 + Z Z 3 Z Z 3 Z Z0 Z Z0 Z 3Z0 Z Z Z 3 + Z Z + Z Z 3 + Z Z 3 + Z Z0 + Z Z0 + Z 3Z0 (E.39) (E.40) In order to calculate the output reflection coefficient we swap indices and. s Z Z Z 3 Z Z 3 + Z Z 3 Z Z 0 Z Z 0 Z 3Z 0 Z Z Z 3 + Z Z + Z Z 3 + Z Z 3 + Z Z 0 + Z Z 0 + Z 3Z 0 (E.4) The calculation of the transmission factors involves the voltage ratio U /U 0. With an auxiliary quantity U x we first determine the following voltage ratios. U U x Z Z 3 + Z and U x U 0 Z (Z 3 + Z ) + Z (Z 3 + Z ) (E.4)
11 APPENDIX E. SOLUTIONS TO PROBLEMS IN CHAPTER 5 Finally, we get Z0 s U U Ux U 0 U x U 0 Z Z (Z 3 + Z ) Z 3 + Z + Z (Z 3 + Z ) Z Z Z Z Z 3 + Z Z + Z Z 3 + Z Z 3 + Z Z0 + Z Z0 + Z 3Z0 (E.43) (E.44) s (E.45) Due to reciprocity we find s s. Special case Z 0 Let us consider the case Z 0 (short circuit). Now, the input reflection coefficient in Equation E.40 becomes s Z Z 3 Z Z 0 Z 3Z 0 Z Z 3 + Z Z 0 + Z 3Z 0 (E.46) This represents the short circuit (r ) at port. The output reflection coefficient in Equation E.4 is now s Z Z 3 Z Z 3 Z Z 3 (Z + Z 3 ) Z Z 3 + Z + Z 3 Z Z 3 + (Z + Z 3 ) Z Z 3 Z + Z 3 Z Z 3 Z Z 3 Z + Z Z Z + Z 3 (E.47) (E.48) This result is correct since the output impedance is Z Z 3. Finally, Equation E.45 gives us zero transmission which is correct. E.4 Problem 5.4 Figure E.0 shows us the signal flow graph of the circuit in Figure 5.5 (book page 85). a e j s x, e j b e j s x, s x, e j b s x, a Figure E.0: Signal flow graph
12 APPENDIX E. SOLUTIONS TO PROBLEMS IN CHAPTER 5 The signal flow graph gives us the following scattering parameters. s b a s x, e jβ(l +l ) s x, e jβl (E.49) a 0 s b a s x, e jβ(l +l ) s x, e jβl (E.50) a 0 s b s x, e jβ(l +l ) (E.5) s b a a 0 a a 0 s x, e jβ(l +l ) (E.5) The transmission lines only modify the phase of the scattering parameters. If the lengths of the lines are known the effect can be compensated. E.5 Problem 5.5 We will derive the equation for the wave source in Figure 5.4 (book page 77). We repeat the representation in Figure E. for convenience. Voltage source Signal flow graph Equations U 0 b a b0 b a r b b r a 0 U Z b0 Z Z Z Z r Z Z Figure E.: Signal flow graph of a voltage source Reflection coefficient r The reflection coefficient is determined by the input impedance of the circuit. The ideal voltage source represents a short circuit. Therefore, the input impedance is and the reflection coefficient is r + (E.53) Wave source The circuit in Figure E. includes an ideal voltage source and is therefore an active circuit. Consequently, there is an outgoing wave b even though there is no incoming wave a. This is expressed by the term b 0 in the following equation. b b 0 + r a (E.54)
13 APPENDIX E. SOLUTIONS TO PROBLEMS IN CHAPTER 5 I U 0 U b a Z 0 Figure E.: Voltage, current and power waves In order to calculate the term b 0, we consider the relation between voltage U and current I and power waves a and b (see Figure E.). The relation between power waves a and b and voltage U and current I is given as b U I and a U + I (E.55) The voltage is determined by the voltage divider rule. The current is given by Ohm s law. U + U 0 (E.56) Therefore, we get and I U 0 + (E.57) a U + I U 0 + ( U 0 ) 0 (E.58) ( + ) b U I U 0 ( U 0 ) ( + ) The term b 0 represents the active part in the signal flow graph. E.6 Problem 5.6 Z0 U0 + b 0 (E.59) Figure E. shows a network with two two-port networks: the first network has a forward gain G f and the feedback network has a gain of G r. From Figure E. we derive the following two relations. This gives us X X + G r Y and Y G f X (E.60) Y G f X (E.6) G cl where G cl G f G r is the closed loop gain. If we apply the result to the signal flow graph in Figure 5. (book page 75), we get s x b a (E.6) s x s y
14 APPENDIX E. SOLUTIONS TO PROBLEMS IN CHAPTER 5 4 X X ' G f Y G r Figure E.: Network with feedback E.7 Problem 5.7 We will calculate reflection coefficients and impedances of the circuit in Figure E.4. We assume the following parameters. f GHz The input impedance Z in is (E.63) 50 Ω (Port reference impedance) (E.64) Z A 00 Ω + jωl 00 Ω + j00 Ω where L 5.9 nh (E.65) Z where C 5 pf (E.66) jωc Z in The reflection coefficient is jωc ( jωc ) + (ωc ) (4.4 j.65) Ω (E.67) r Z in Z in + Re {Z in} + Im {Z in } Z 0 + j Im {Z in} (Re {Z in } + ) + Im {Z in } (E.68) e 8.5 (E.69) Zin r Z in r U 0 Z, ZA Figure E.4: Network In order to determine the reflection coefficient r we first consider the reflection coefficient r at the end of the line. r Z A Z A + Re {Z A} + Im {Z A } Z 0 + j Im {Z A} (Re {Z A } + ) + Im {Z A } 0.6 e j9.75 (E.70) (E.7)
15 APPENDIX E. SOLUTIONS TO PROBLEMS IN CHAPTER 5 5 At the input of the transmission line we get r r e jβl 0.6 e j9.75 e j e j8.4 r (E.7) If we compare the reflection coefficients r and r we see that r r (complex conjugate matching). Using a Smith-Chart gives us the input impedance Z in (see Figure E.5). We apply a commercial circuit simulator (ADS by Agilent, inc.). The electrical line length is 0.363λ The load impedance is represented by a black diamond the input impedance is depicted by a red square. We read from the diagram Z in (4.8 + j.56) Ω Z in (E.73) Impedances Z in and Z in as well as reflection coefficients r and r show complex conjugate values. Figure E.5: Smith chart and input impedance Z in Circuit simulation We will validate our result by performing a circuit simulation. In our previous calculation we considered a frequeny of f GHz. Now we extend the frequency range from 00 MHz to GHz. Figure E.6 shows the schematic. The results are given in Figure E.7. The upper diagrams in Figure E.7 show reflection coefficients (magnitude and phase) as well as input impedances (real and imaginary part). In order to compare the results with our simulation we have to look at a frequency of f GHz (indicated by markers). The simulation results agree with our previously calculated values.
16 APPENDIX E. SOLUTIONS TO PROBLEMS IN CHAPTER 5 6 Figure E.6: Schematic Figure E.7: Simulation results: s-parameters and impedances
17 APPENDIX E. SOLUTIONS TO PROBLEMS IN CHAPTER 5 7 E.8 Problem 5.8 A three-port network shall have the following three properties: matching at all ports (s ii 0), reciprocity (s ij s ji ) and no losses (S T S I). From these requirements the matrix equation 0 s s 0 s s 0 0 s 0 s 3 s 0 s s s 3 0 s s gives us the following set of equations (E.74) s + s (E.75) s s 3 0 (E.76) s s 3 0 (E.77) s 3 s 0 (E.78) s + s 3 (E.79) s s 0 (E.80) s 3 s 0 (E.8) s s 0 (E.8) s + s 3 (E.83) From Equations E.76 and E.77 we get (for s 3 0): s s (E.84) From Equation E.80 we then conclude: s s 0 (E.85) This result contradicts Equation E.75 since s + s 0 (Conflict for s 3 0) (E.86) The conflict can be solved for s 3 0. This implies (Equation E.79) and (Equation E.83) This result contradicts Equation E.75 since s (E.87) s (E.88) s + s (Conflict for s 3 0) (E.89) The set of equations shows that a three-port network cannot satisfy the following conditions simultaneously
18 APPENDIX E. SOLUTIONS TO PROBLEMS IN CHAPTER 5 8 matching at all ports (s ii 0), reciprocity (s ij s ji ) and losslessness. (Last modified: 0.0.0)
Solutions to Problems in Chapter 6
Appendix F Solutions to Problems in Chapter 6 F.1 Problem 6.1 Short-circuited transmission lines Section 6.2.1 (book page 193) describes the method to determine the overall length of the transmission line
More informationMicrowave Network Analysis Lecture 1: The Scattering Parameters
Microwave Network Analysis Lecture : The Scattering Parameters ELC 305a Fall 0 Department of Electronics and Communications Engineering Faculty of Engineering Cairo University Outline Review on Network
More informationTransmission line equations in phasor form
Transmission line equations in phasor form Kenneth H. Carpenter Department of Electrical and Computer Engineering Kansas State University November 19, 2004 The text for this class presents transmission
More informationModule 13: Network Analysis and Directional Couplers
Module 13: Network Analysis and Directional Couplers 13.2 Network theory two port networks, S-parameters, Z-parameters, Y-parameters The study of two port networks is important in the field of electrical
More informationTRANSMISSION LINES AND MATCHING
TRANSMISSION LINES AND MATCHING for High-Frequency Circuit Design Elective by Michael Tse September 2003 Contents Basic models The Telegrapher s equations and solutions Transmission line equations The
More informationLAB MANUAL EXPERIMENT NO. 7
LAB MANUAL EXPERIMENT NO. 7 Aim of the Experiment: Concept of Generalized N-port scattering parameters, and formulation of these parameters into 2-port reflection and transmission coefficients. Requirement:
More informationECE 391 supplemental notes - #11. Adding a Lumped Series Element
ECE 391 supplemental notes - #11 Adding a umped Series Element Consider the following T-line circuit: Z R,1! Z,2! Z z in,1 = r in,1 + jx in,1 Z in,1 = z in,1 Z,1 z = Z Z,2 zin,2 = r in,2 + jx in,2 z,1
More informationLowpass L Matching Network Designer
Lowpass L Matching Network Designer V S L V L I S j*x S C j*x L Table of Contents I. General Impedance Matching II. Impedance Transformation for Power Amplifiers III. Inputs IV. Calculations V. Outputs
More informationINF5481 RF Circuit, Theory and Design Assignment #3
INF548 RF Circuit, Theory and Design ssignment #3 Problem We have the two port network in figure, which is a cascade of two identical networks consisting of a single shunt and series impedance. Find the
More informationECE357H1S ELECTROMAGNETIC FIELDS TERM TEST 1. 8 February 2016, 19:00 20:00. Examiner: Prof. Sean V. Hum
UNIVERSITY OF TORONTO FACULTY OF APPLIED SCIENCE AND ENGINEERING The Edward S. Rogers Sr. Department of Electrical and Computer Engineering ECE57HS ELECTROMAGNETIC FIELDS TERM TEST 8 February 6, 9:00 :00
More informationScattering Parameters
Berkeley Scattering Parameters Prof. Ali M. Niknejad U.C. Berkeley Copyright c 2016 by Ali M. Niknejad September 7, 2017 1 / 57 Scattering Parameters 2 / 57 Scattering Matrix Voltages and currents are
More informationFINAL EXAM IN FYS-3007
Page 1 of 4 pages + chart FINAL EXAM IN FYS-007 Exam in : Fys-007 Microwave Techniques Date : Tuesday, May 1, 2011 Time : 09.00 1.00 Place : Åsgårdveien 9 Approved remedies : All non-living and non-communicating
More informationLecture 4: R-L-C Circuits and Resonant Circuits
Lecture 4: R-L-C Circuits and Resonant Circuits RLC series circuit: What's V R? Simplest way to solve for V is to use voltage divider equation in complex notation: V X L X C V R = in R R + X C + X L L
More informationLecture 13 Date:
ecture 3 Date: 6.09.204 The Signal Flow Graph (Contd.) Impedance Matching and Tuning Tpe Matching Network Example Signal Flow Graph (contd.) Splitting Rule Now consider the three equations SFG a a b 2
More informationTransmission Line Theory
S. R. Zinka zinka@vit.ac.in School of Electronics Engineering Vellore Institute of Technology April 26, 2013 Outline 1 Free Space as a TX Line 2 TX Line Connected to a Load 3 Some Special Cases 4 Smith
More informationarxiv: v1 [physics.acc-ph] 19 Jan 2012
RF engineering basic concepts: the Smith chart F. Caspers CERN, Geneva, Switzerland arxiv:68v [physics.acc-ph] 9 Jan Motivation Abstract The Smith chart is a very valuable and important tool that facilitates
More informationEE 205 Dr. A. Zidouri. Electric Circuits II. Two-Port Circuits Two-Port Parameters. Lecture #42
EE 05 Dr. A. Zidouri Electric Circuits Two-Port Circuits Two-Port Parameters Lecture #4-1 - EE 05 Dr. A. Zidouri The material to be covered in this lecture is as follows: o ntroduction to two-port circuits
More informationA UNEQUAL COUPLED-LINE WILKINSON POWER DI- VIDER FOR ARBITRARY TERMINATED IMPEDANCES
Progress In Electromagnetics Research, Vol. 117, 181 194, 211 A UNEQUAL COUPLED-LINE WILKINSON POWER DI- VIDER FOR ARBITRARY TERMINATED IMPEDANCES Y. Wu * and Y. Liu School of Electronic Engineering, Beijing
More informationR-L-C Circuits and Resonant Circuits
P517/617 Lec4, P1 R-L-C Circuits and Resonant Circuits Consider the following RLC series circuit What's R? Simplest way to solve for is to use voltage divider equation in complex notation. X L X C in 0
More informationIMPEDANCE and NETWORKS. Transformers. Networks. A method of analysing complex networks. Y-parameters and S-parameters
IMPEDANCE and NETWORKS Transformers Networks A method of analysing complex networks Y-parameters and S-parameters 1 ENGN4545/ENGN6545: Radiofrequency Engineering L#7 Transformers Combining the effects
More informationIntroduction. A microwave circuit is an interconnection of components whose size is comparable with the wavelength at the operation frequency
Introduction A microwave circuit is an interconnection of components whose size is comparable with the wavelength at the operation frequency Type of Components: Interconnection: it is not an ideal connection
More informationLecture 12. Microwave Networks and Scattering Parameters
Lecture Microwave Networs and cattering Parameters Optional Reading: teer ection 6.3 to 6.6 Pozar ection 4.3 ElecEng4FJ4 LECTURE : MICROWAE NETWORK AND -PARAMETER Microwave Networs: oltages and Currents
More informationy(d) = j
Problem 2.66 A 0-Ω transmission line is to be matched to a computer terminal with Z L = ( j25) Ω by inserting an appropriate reactance in parallel with the line. If f = 800 MHz and ε r = 4, determine the
More informationSinusoidal Steady State Analysis (AC Analysis) Part I
Sinusoidal Steady State Analysis (AC Analysis) Part I Amin Electronics and Electrical Communications Engineering Department (EECE) Cairo University elc.n102.eng@gmail.com http://scholar.cu.edu.eg/refky/
More informationLecture 7: Two-Ports (2)
Lecture 7: Two-Ports (2) Amin Arbabian Jan M. Rabaey EE142 Fall 2010 Sept. 16 th, 2010 Announcements HW3 Posted, due Thursday September 23 rd, 330pm EE142 drop box. Office hours Two-Port notes by Professor
More informationand Ee = E ; 0 they are separated by a dielectric material having u = io-s S/m, µ, = µ, 0
602 CHAPTER 11 TRANSMISSION LINES 11.10 Two identical pulses each of magnitude 12 V and width 2 µs are incident at t = 0 on a lossless transmission line of length 400 m terminated with a load. If the two
More informationDesign of SPUDT and RSPUDT SAW Filters
Dr. A.S.Rukhlenko Design of SPUDT and RSPUDT SAW Filters Rukhlenko@bluewin.ch www.intrasaw.com Neuchâtel, 2005 1 Outline Introduction 1. Single Phase Unidirectional SAW Transducer (SPUDT) 2. SPUDT Design
More informationImaginary Impedance Axis. Real Impedance Axis. Smith Chart. The circles, tangent to the right side of the chart, are constant resistance circles
The Smith Chart The Smith Chart is simply a graphical calculator for computing impedance as a function of reflection coefficient. Many problems can be easily visualized with the Smith Chart The Smith chart
More informationTwo Port Networks. Definition of 2-Port Network A two-port network is an electrical network with two separate ports for input and output
Two Port Networks Definition of 2-Port Network A two-port network is an electrical network with two separate ports for input and output What is a Port? It is a pair of terminals through which a current
More informationSeries & Parallel Resistors 3/17/2015 1
Series & Parallel Resistors 3/17/2015 1 Series Resistors & Voltage Division Consider the single-loop circuit as shown in figure. The two resistors are in series, since the same current i flows in both
More informationIPC-TM-650 TEST METHODS MANUAL
ASSOCIATION CONNECTING ELECTRONICS INDUSTRIES 3000 Lakeside Drive, Suite 309S Bannockburn, IL 60015-1219 TEST METHODS MANUAL Number High Frequency Testing to Determine Permittivity and Loss Originating
More informationECE Microwave Engineering
ECE 537-635 Microwave Engineering Fall 8 Prof. David R. Jackson Dept. of ECE Adapted from notes by Prof. Jeffery T. Williams Notes Power Dividers and Circulators Power Dividers and Couplers A power divider
More informationFour Ports. 1 ENGN4545/ENGN6545: Radiofrequency Engineering L#16
Four Ports Theorems of four port networks 180 o and 90 o Hybrids Directional couplers Transmission line transformers, Four port striplines Rat-races, Wilkinsons, Magic-T s Circulators, Diplexers and Filter
More informationECE 107: Electromagnetism
ECE 107: Electromagnetism Set 2: Transmission lines Instructor: Prof. Vitaliy Lomakin Department of Electrical and Computer Engineering University of California, San Diego, CA 92093 1 Outline Transmission
More informationLecture 2 - Transmission Line Theory
Lecture 2 - Transmission Line Theory Microwave Active Circuit Analysis and Design Clive Poole and Izzat Darwazeh Academic Press Inc. Poole-Darwazeh 2015 Lecture 2 - Transmission Line Theory Slide1 of 54
More informationMatched, Lossless, Reciprocal Devices
/3/7 Matched reciprocal lossless 73 /9 Matched, Lossless, Reciprocal Devices As we discussed earlier, a device can be lossless or reciprocal. In addition, we can likewise classify it as being matched.
More informationMatched, Lossless, Reciprocal Devices
/6/009 Matched reciprocal lossless present / Matched, Lossless, Reciprocal Devices As we discussed earlier, a device can be lossless or reciprocal. In addition, we can likewise classify it as being matched.
More informationLecture 23: Basic Properties of Dividers and Couplers.
Whites, EE 48/58 Lecture 23 age of 9 Lecture 23: Basic roperties of Dividers and Couplers. For the remainder of this course we re going to investigate a plethora of microwave devices and circuits both
More informationEECS 242: Amplifier Design Examples
EECS 242: Amplifier Design Examples Small-Signal Transistor Model Intrinsic transistor model Using basic equations, let s assume we have the following process: f T = 100 GHz A v0 = 10, V t = 0.3V, V gs
More informationECE 546 Lecture 13 Scattering Parameters
ECE 546 Lecture 3 Scattering Parameters Spring 08 Jose E. Schutt-Aine Electrical & Computer Engineering University of Illinois jesa@illinois.edu ECE 546 Jose Schutt Aine Transfer Function Representation
More informationTransmission Lines in the Frequency Domain
Berkeley Transmission Lines in the Frequency Domain Prof. Ali M. Niknejad U.C. Berkeley Copyright c 2016 by Ali M. Niknejad August 30, 2017 1 / 38 Why Sinusoidal Steady-State? 2 / 38 Time Harmonic Steady-State
More informationPulses in transmission lines
Pulses in transmission lines Physics 401, Fall 013 Eugene V. Colla Definition Distributed parameters networ Pulses in transmission line Wave equation and wave propagation eflections. esistive load Thévenin's
More informationEE 40: Introduction to Microelectronic Circuits Spring 2008: Midterm 2
EE 4: Introduction to Microelectronic Circuits Spring 8: Midterm Venkat Anantharam 3/9/8 Total Time Allotted : min Total Points:. This is a closed book exam. However, you are allowed to bring two pages
More informationTwo-Port Networks Admittance Parameters CHAPTER16 THE LEARNING GOALS FOR THIS CHAPTER ARE THAT STUDENTS SHOULD BE ABLE TO:
CHAPTER16 Two-Port Networks THE LEARNING GOALS FOR THIS CHAPTER ARE THAT STUDENTS SHOULD BE ABLE TO: Calculate the admittance, impedance, hybrid, and transmission parameter for two-port networks. Convert
More informationExperiment 06 - Extraction of Transmission Line Parameters
ECE 451 Automated Microwave Measurements Laboratory Experiment 06 - Extraction of Transmission Line Parameters 1 Introduction With the increase in both speed and complexity of mordern circuits, modeling
More informationError Correction in Vector Network Analyzers
Error Correction in Vector Network Analyzers Thomas C. Baier, DG8SAQ May 19, 2009 Abstract This article describes systematic errors encountered in vector network analysis and how they can be mathematically
More informationMicrowave Network Analysis
Prof. Dr. Mohammad Tariqul Islam titareq@gmail.my tariqul@ukm.edu.my Microwave Network Analysis 1 Text Book D.M. Pozar, Microwave engineering, 3 rd edition, 2005 by John-Wiley & Sons. Fawwaz T. ILABY,
More informationNetwork Graphs and Tellegen s Theorem
Networ Graphs and Tellegen s Theorem The concepts of a graph Cut sets and Kirchhoff s current laws Loops and Kirchhoff s voltage laws Tellegen s Theorem The concepts of a graph The analysis of a complex
More informationAdvancements in mm-wave On-Wafer Measurements: A Commercial Multi-Line TRL Calibration Author: Leonard Hayden Presenter: Gavin Fisher
Advancements in mm-wave On-Wafer Measurements: A Commercial Multi-Line TRL Calibration Author: Leonard Hayden Presenter: Gavin Fisher The title of this section is A Commercial Multi-Line TRL Calibration
More informationContents. Transmission Lines The Smith Chart Vector Network Analyser (VNA) ü structure ü calibration ü operation. Measurements
Contents Transmission Lines The Smith Chart Vector Network Analyser (VNA) ü structure ü calibration ü operation Measurements Göran Jönsson, EIT 2015-04-27 Vector Network Analysis 2 Waves on Lines If the
More informationWaves on Lines. Contents. ! Transmission Lines! The Smith Chart! Vector Network Analyser (VNA) ! Measurements
Waves on Lines If the wavelength to be considered is significantly greater compared to the size of the circuit the voltage will be independent of the location. amplitude d! distance but this is not true
More informationAC analysis - many examples
AC analysis - many examples The basic method for AC analysis:. epresent the AC sources as complex numbers: ( ). Convert resistors, capacitors, and inductors into their respective impedances: resistor Z
More informationBerkeley. The Smith Chart. Prof. Ali M. Niknejad. U.C. Berkeley Copyright c 2017 by Ali M. Niknejad. September 14, 2017
Berkeley The Smith Chart Prof. Ali M. Niknejad U.C. Berkeley Copyright c 17 by Ali M. Niknejad September 14, 17 1 / 29 The Smith Chart The Smith Chart is simply a graphical calculator for computing impedance
More informationChapter - 7 Power Dividers and Couplers
4//7 7_1 Basic Properties of Dividers and Couplers 1/ Chapter - 7 Power Dividers and Couplers One of the most fundamental problems in microwave engineering is how to efficiently divide signal power. 1.
More informationTHE MINIMUM LOSS OF IMPEDANCE MATCHING TWO-PORTS
THE MINIMUM LOSS OF IMPEDANCE MATCHING TWO-PORTS By J. SOLYMOSI Institute of Communication Electronics, Technical University, Budapest Received FebrucTv 27, 1979 Presented by Prof. Dr. S. CSIBI 1. Characterization
More informationA Novel Tunable Dual-Band Bandstop Filter (DBBSF) Using BST Capacitors and Tuning Diode
Progress In Electromagnetics Research C, Vol. 67, 59 69, 2016 A Novel Tunable Dual-Band Bandstop Filter (DBBSF) Using BST Capacitors and Tuning Diode Hassan Aldeeb and Thottam S. Kalkur * Abstract A novel
More informationSurface Mount Chip Capacitors
Features High '' Factor at high frequencies High RF power capabilities Low High self resonant frequencies Excellent stability across temperature range Small size High Frequency Measurement and Performance
More informationMicrowave Network Analysis
Microwave Network Analysis S R Zinka zinka@hyderabadbits-pilaniacin Department of Electrical & Electronics Engineering BITS Pilani, Hyderbad Campus May 7, 2015 RF & Microwave Engineering, Dept of EEE,
More informationLectures: Lumped element filters (also applies to low frequency filters) Stub Filters Stepped Impedance Filters Coupled Line Filters
ECE 580/680 Microwave Filter Design Lectures: Lumped element filters (also applies to low frequency filters) Stub Filters Stepped Impedance Filters Coupled Line Filters Lumped Element Filters Text Section
More informationECE145A/218A Course Notes
ECE145A/218A Course Notes Last note set: Introduction to transmission lines 1. Transmission lines are a linear system - superposition can be used 2. Wave equation permits forward and reverse wave propagation
More informationInternational Distinguished Lecturer Program
U 005-006 International Distinguished Lecturer Program Ken-ya Hashimoto Chiba University Sponsored by The Institute of Electrical and Electronics Engineers (IEEE) Ultrasonics, Ferroelectrics and Frequency
More informationContents. ! Transmission Lines! The Smith Chart! Vector Network Analyser (VNA) ! Measurements. ! structure! calibration! operation
Contents! Transmission Lines! The Smith Chart! Vector Network Analyser (VNA)! structure! calibration! operation! Measurements Göran Jönsson, EIT 2009-11-16 Network Analysis 2! Waves on Lines! If the wavelength
More information1.3 Sinusoidal Steady State
1.3 Sinusoidal Steady State Electromagnetics applications can be divided into two broad classes: Time-domain: Excitation is not sinusoidal (pulsed, broadband, etc.) Ultrawideband communications Pulsed
More informationChapter 5 Steady-State Sinusoidal Analysis
Chapter 5 Steady-State Sinusoidal Analysis Chapter 5 Steady-State Sinusoidal Analysis 1. Identify the frequency, angular frequency, peak value, rms value, and phase of a sinusoidal signal. 2. Solve steady-state
More informationAPPENDIX: TRANSMISSION LINE MODELLING AND PORT-BASED CIRCUITS
APPENDIX: TRANSMISSION LINE MODELLING AND PORT-BASED CIRCUITS A. MODELLING TRANSMISSION LINES THROUGH CIRCUITS In Chapter 5 we introduced the so-called basic rule for modelling circuital systems through
More informationLecture Outline. Shorted line (Z L = 0) Open circuit line (Z L = ) Matched line (Z L = Z 0 ) 9/28/2017. EE 4347 Applied Electromagnetics.
9/8/17 Course Instructor Dr. Raymond C. Rumpf Office: A 337 Phone: (915) 747 6958 E Mail: rcrumpf@utep.edu EE 4347 Applied Electromagnetics Topic 4b Transmission ine Behavior Transmission These ine notes
More informationRF Engineering Basic Concepts: The Smith Chart
RF Engineering Basic Concepts: The Smith Chart F. Caspers CERN, Geneva, Switzerland Motivation Abstract The Smith chart is a very valuable and important tool that facilitates interpretation of S-parameter
More informationLecture (5) Power Factor,threephase circuits, and Per Unit Calculations
Lecture (5) Power Factor,threephase circuits, and Per Unit Calculations 5-1 Repeating the Example on Power Factor Correction (Given last Class) P? Q? S? Light Motor From source 1000 volts @ 60 Htz 10kW
More informationCHAPTER 6 STEADY-STATE ANALYSIS OF SINGLE-PHASE SELF-EXCITED INDUCTION GENERATORS
79 CHAPTER 6 STEADY-STATE ANALYSIS OF SINGLE-PHASE SELF-EXCITED INDUCTION GENERATORS 6.. INTRODUCTION The steady-state analysis of six-phase and three-phase self-excited induction generators has been presented
More informationSinusoidal Steady-State Analysis
Sinusoidal Steady-State Analysis Mauro Forti October 27, 2018 Constitutive Relations in the Frequency Domain Consider a network with independent voltage and current sources at the same angular frequency
More informationElectricity and Light Pre Lab Questions
Electricity and Light Pre Lab Questions The pre lab questions can be answered by reading the theory and procedure for the related lab. You are strongly encouraged to answers these questions on your own.
More informationProgress In Electromagnetics Research C, Vol. 33, , 2012
Progress In Electromagnetics Research C, Vol. 33, 213 227, 2012 MAXIMUM BANDWIDTH PERFORMANCE FOR AN IDEAL LUMPED-ELEMENT CIRCULATOR H. Dong *, J. L. Young, J. R. Smith, and B. Aldecoa Department of Electrical
More informationHow to measure complex impedance at high frequencies where phase measurement is unreliable.
Objectives In this course you will learn the following Various applications of transmission lines. How to measure complex impedance at high frequencies where phase measurement is unreliable. How and why
More informationRipple Method for Evaluating Residual Errors
Ripple Method for Evaluating Residual Errors H. Heuermann Univ. of Applied Sciences Aachen, Institute of High Frequency Tech., Eupener Str. 7, D-5266 Aachen, Germany Heuermann@FH-Aachen.de Heuermann HF-Technik
More informationANTENNAS and MICROWAVES ENGINEERING (650427)
Philadelphia University Faculty of Engineering Communication and Electronics Engineering ANTENNAS and MICROWAVES ENGINEERING (65427) Part 2 Dr. Omar R Daoud 1 General Considerations It is a two-port network
More information2.5 Operations With Complex Numbers in Rectangular Form
2.5 Operations With Complex Numbers in Rectangular Form The computer-generated image shown is called a fractal. Fractals are used in many ways, such as making realistic computer images for movies and squeezing
More informationMicrowave Oscillators Design
Microwave Oscillators Design Oscillators Classification Feedback Oscillators β Α Oscillation Condition: Gloop = A β(jω 0 ) = 1 Gloop(jω 0 ) = 1, Gloop(jω 0 )=2nπ Negative resistance oscillators Most used
More informationVoltage reflection coefficient Γ. L e V V. = e. At the load Γ (l = 0) ; Γ = V V
of 3 Smith hart Tutorial Part To begin with we start with the definition of SWR, which is the ratio of the reflected voltage over the incident voltage. The Reflection coefficient Γ is simply the complex
More informationCURRENT SOURCES EXAMPLE 1 Find the source voltage Vs and the current I1 for the circuit shown below SOURCE CONVERSIONS
CURRENT SOURCES EXAMPLE 1 Find the source voltage Vs and the current I1 for the circuit shown below EXAMPLE 2 Find the source voltage Vs and the current I1 for the circuit shown below SOURCE CONVERSIONS
More informationKimmo Silvonen, Transmission lines, ver
Kimmo Silvonen, Transmission lines, ver. 13.10.2008 1 1 Basic Theory The increasing operating and clock frequencies require transmission line theory to be considered more and more often! 1.1 Some practical
More informationDual-Polarization Scattering at Transmission-Line Junctions
Interaction Notes Note 605 21 January 2008 Dual-Polarization Scattering at ransmission-line Junctions Carl E. Baum University of New Mexico Department of Electrical and Computer Engineering Albuquerque
More information55:041 Electronic Circuits The University of Iowa Fall Final Exam
Final Exam Name: Score Max: 135 Question 1 (1 point unless otherwise noted) a. What is the maximum theoretical efficiency for a class-b amplifier? Answer: 78% b. The abbreviation/term ESR is often encountered
More informationElectric Circuit Theory
Electric Circuit Theory Nam Ki Min nkmin@korea.ac.kr 010-9419-2320 Chapter 18 Two-Port Circuits Nam Ki Min nkmin@korea.ac.kr 010-9419-2320 Contents and Objectives 3 Chapter Contents 18.1 The Terminal Equations
More informationEE Power Gain and Amplifier Design 10/31/2017
EE 40458 Power Gain and Amplifier Design 10/31/017 Motivation Brief recap: We ve studied matching networks (several types, how to design them, bandwidth, how they work, etc ) Studied network analysis techniques
More informationBlack Box Modelling of Power Transistors in the Frequency Domain
Jan Verspecht bvba Mechelstraat 17 B-1745 Opwijk Belgium email: contact@janverspecht.com web: http://www.janverspecht.com Black Box Modelling of Power Transistors in the Frequency Domain Jan Verspecht
More informationQuantifying and Verifying trace stability of vector network analyzers at frequencies below 1GHz
1 Quantifying and Verifying trace stability of vector network analyzers at frequencies below 1GHz Hamdi Mani, Chris Groppi, Judd Bowman Abstract we describe measurements done to check the low frequency
More informationIntroduction to Network Analysis of Microwave Circuits
1 Introduction to Network Analysis of Microwave Circuits ABSTRACT Network presentation has been used as a technique in the analysis of lowfrequency electrical electronic circuits. The same technique is
More informationPrepared by: Eng. Talal F. Skaik
Islamic University of Gaza Faculty of Engineering Electrical & Computer Dept. Prepared by: Eng. Talal F. Skaik Microwaves Lab Experiment #3 Single Stub Matching Objectives: Understanding Impedance Matching,
More informationContents. Transmission Lines The Smith Chart Vector Network Analyser (VNA) ü structure ü calibration ü operation. Measurements
Contents Transmission Lines The Smith Chart Vector Network Analyser (VNA) ü structure ü calibration ü operation Measurements Göran Jönsson, EIT 2017-05-12 Vector Network Analysis 2 Waves on Lines If the
More information(amperes) = (coulombs) (3.1) (seconds) Time varying current. (volts) =
3 Electrical Circuits 3. Basic Concepts Electric charge coulomb of negative change contains 624 0 8 electrons. Current ampere is a steady flow of coulomb of change pass a given point in a conductor in
More informationScattering at One-Dimensional-Transmission-Line Junctions
Interaction Notes Note 603 15 March 007 Scattering at One-Dimensional-ransmission-Line Junctions Carl E. Baum University of New Mexico Department of Electrical and Computer Engineering Albuquerque New
More informationLeft-Handed (LH) Structures and Retrodirective Meta-Surface
Left-Handed (LH Structures and Retrodirective Meta-Surface Christophe Caloz, Lei Liu, Ryan Miyamoto and Tatsuo Itoh Electrical Engineering Department University of California, Los Angeles AGENDA I. LH
More informationSTUDY OF LOSS EFFECT OF TRANSMISSION LINES AND VALIDITY OF A SPICE MODEL IN ELECTROMAG- NETIC TOPOLOGY
Progress In Electromagnetics Research, PIER 90, 89 103, 2009 STUDY OF LOSS EFFECT OF TRANSMISSION LINES AND VALIDITY OF A SPICE MODEL IN ELECTROMAG- NETIC TOPOLOGY H. Xie, J. Wang, R. Fan, andy. Liu Department
More informationWhat s Your (real or imaginary) LCR IQ?
Chroma Systems Solutions, Inc. What s Your (real or imaginary) LCR IQ? 11021, 11025 LCR Meter Keywords:. Impedance, Inductance, Capacitance, Resistance, Admittance, Conductance, Dissipation Factor, 4-Terminal
More informationTECHNO INDIA BATANAGAR
TECHNO INDIA BATANAGAR ( DEPARTMENT OF ELECTRONICS & COMMUNICATION ENGINEERING) QUESTION BANK- 2018 1.Vector Calculus Assistant Professor 9432183958.mukherjee@tib.edu.in 1. When the operator operates on
More informationECE414/514 Electronics Packaging Spring 2012 Lecture 6 Electrical D: Transmission lines (Crosstalk) Lecture topics
ECE414/514 Electronics Packaging Spring 2012 Lecture 6 Electrical D: Transmission lines (Crosstalk) James E. Morris Dept of Electrical & Computer Engineering Portland State University 1 Lecture topics
More informationSmith Chart The quarter-wave transformer
Smith Chart The quarter-wave transformer We will cover these topics The Smith Chart The Quarter-Wave Transformer Watcharapan Suwansan8suk #3 EIE/ENE 450 Applied Communica8ons and Transmission Lines King
More informationMidterm Exam (closed book/notes) Tuesday, February 23, 2010
University of California, Berkeley Spring 2010 EE 42/100 Prof. A. Niknejad Midterm Exam (closed book/notes) Tuesday, February 23, 2010 Guidelines: Closed book. You may use a calculator. Do not unstaple
More informationSmith Chart Figure 1 Figure 1.
Smith Chart The Smith chart appeared in 1939 as a graph-based method of simplifying the complex math (that is, calculations involving variables of the form x + jy) needed to describe the characteristics
More informationIII. The STM-8 Loop - Work in progress
III. The STM-8 Loop - Work in progress This contains the loop functions for a velocity input. The interaction between, forward gain, feedback function, loop gain and transfer function are well displayed.
More information